Get Controls -> Operating the Switches Around the Steering Wheel Guide for Honda Jazz 4 Door Third Generation (2016-2020)

18 FIT JAZZ-32T5A6100.book 164 ページ２０１７年８月２３日　水曜日　午前１１時２４分

Operating the Switches Around the Steering Wheel

Models without keyless access system

Ignition Switch

1Ignition Switch

Manual transmission models

3

WARNING

(0 LOCK: Insert and remove the key in this

position.

Removing the key from the ignition switch

while driving locks the steering. This can

cause you to lose control of the vehicle.

(q ACCESSORY: Operate the audio system and

other accessories in this position.

(w ON: This is the position when driving.

Remove the key from the ignition switch

only when parked.

(e START: This position is for starting the engine.

The switch returns to ON (w when you let go of

the key.

Continuously variable transmission models

You cannot take the key out unless the shift lever is

in (P.

All models

If you open the driver's door when the key is in LOCK

(0 or ACCESSORY (q, the following symbol appears

on the multi-information display:

• In LOCK (0: symbol

• In ACCESSORY (q: symbol

If the key won’t turn from LOCK (0 to ACCESSORY

(q, turn the key while moving the steering wheel left

and right. The steering wheel will unlock, allowing

the key to turn.

164

18 FIT JAZZ-32T5A6100.book 165 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluENGINE START/STOP Button

Models with keyless access system

ENGINE START/STOP Button

1ENGINE START/STOP Button

ENGINE START/STOP Button Operating Range

You can start the engine when the keyless remote is

inside the vehicle.

Changing the Power Mode

■

Continuously Variable Transmission

VEHICLE OFF (LOCK)

Manual Transmission

Operating Range

The button is off.

The steering wheel is locked.

The power to all electrical

components is turned off.

ACCESSORY

The button blinks (in red).

Operate the audio system and

other accessories in this

position.

The engine may also run if the keyless remote is close

to the door or window, even if it is outside the

vehicle.

ON mode:

ON

The button is on (in red), if the engine is running.

The button blinks (in red).

All electrical components can

be used.

If the battery of the keyless remote is getting low, the

engine may not start when you push the ENGINE

START/STOP button. If the engine does not start,

refer to the following link.

Without depressing

the brake pedal

Without depressing

the clutch pedal

2 If the Keyless Remote Battery is Weak

P. 560

Press the button.

Press the button without the shift lever in (P.

Shift to (P then press the button.

Continued

165

18 FIT JAZZ-32T5A6100.book 166 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluENGINE START/STOP Button

1ENGINE START/STOP Button

Automatic Power Off

■

If the power mode does not change from VEHICLE

OFF to ACCESSORY, press the ENGINE START/STOP

button while moving the steering wheel left and

right. The steering wheel will unlock, allowing the

mode to change.

If you leave the vehicle for 30 to 60 minutes with the shift lever in (P^*1and the

power mode in ACCESSORY, the vehicle automatically goes into the mode similar to

VEHICLE OFF (LOCK) to avoid draining the battery.

When in this mode:

The steering wheel does not lock.

You cannot lock or unlock doors with the remote transmitter or the keyless access

system.

Do not leave the power mode in ACCESSORY or ON

when you get out.

Press the ENGINE START/STOP button twice to switch the mode to VEHICLE OFF

(LOCK).

2 Changing the Power Mode P. 165

*1: Continuously variable transmission models

166

18 FIT JAZZ-32T5A6100.book 167 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluENGINE START/STOP Button

Power Mode Reminder

■

If you open the driver’s door when the power mode is set to ACCESSORY, a warning

beep sounds.

1Keyless Remote Reminder

Keyless Remote Reminder

■

When the keyless remote is within the system’s

operational range, and the driver’s door is closed, the

warning function cancels.

Warning buzzers may sound from inside and/

or outside the vehicle to remind you that the

keyless remote is out of the vehicle. If the

buzzer continues even after the remote is put

back inside, place it to be within its

operational range.

If the keyless remote is taken out of the vehicle after

the engine has been started, you can no longer

change the ENGINE START/STOP button mode or

restart the engine. Always make sure if the remote is

in your vehicle when you operate the ENGINE

START/STOP button.

■ When the power mode is in ON

If the keyless remote is taken out of the

vehicle, and the driver’s door is closed, a

warning buzzer sound from both inside and

outside the vehicle. A warning symbol on the

multi-information display notifies the driver

inside that the remote is outside of the

vehicle.

Removing the keyless remote from the vehicle

through a window does not activate the warning

buzzer.

Do not put the keyless remote on the dashboard or in

the glove box. It may cause the warning buzzer to go

off. Under some other conditions that can prevent

the vehicle from locating the remote, the warning

buzzer may also go off even if the remote is within

the system’s operational range.

■ When the power mode is in

ACCESSORY

If the keyless remote is taken out of the

vehicle, and all the doors are closed, a

warning buzzer sounds from outside the

vehicle.

167

18 FIT JAZZ-32T5A6100.book 168 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluIgnition Switch and Power Mode Comparison

Ignition Switch and Power Mode Comparison

Ignition Switch

Position

LOCK (0

(with/without

the key)

ACCESSORY (q

ON (w

START (e

●

Without Keyless

Access System

Engine is turned off and

power is shut down.

The steering wheel is

locked.

No electrical

components can be

used.

Engine is turned off.

Some electrical

components such as the

audio system and the

accessory power socket

can be operated.

Normal key position

while driving.

All electrical components

can be used.

Use this position to start

the engine.

The ignition switch

returns to ON (w

position when you

release the key.

●

Power Mode

VEHICLE OFF

(LOCK)

ACCESSORY

ON

START

Button is: Blinking On

With Keyless Access Button-Off

Button-Blinking in red

(engine is turned off)

On in red (engine is

Button-On in red

The mode automatically

returns to ON after the

engine starts.

●

System and ENGINE

START/STOP

Button

Engine is turned off and

Engine is turned off.

Some electrical

●

power is shut down.

The steering wheel is

locked.

●

components such as the running)

●

audio system and the

accessory power socket

can be operated.

All electrical components

can be used.

No electrical

components can be

used.

168

18 FIT JAZZ-32T5A6100.book 169 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluTurn Signals

Turn Signals

The turn signals can be used when the ignition

switch is in ON (w^*1.

Right Turn

■ One touch turn signal

When you lightly push up or down and release

the turn signal lever, the exterior turn signals

and turn signal indicator blink three times.

Left Turn

This feature can be used when signalling for a

lane change.

*1: Models with the keyless access system have an ENGINE START/STOP button instead of an ignition

switch.

169

18 FIT JAZZ-32T5A6100.book 170 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluLight Switches

Light Switches

1Light Switches

Manual Operation

■

Models without keyless access system

If you remove the key from the ignition switch while

the lights are on, a chime sounds when the driver’s

door is opened.

Rotating the light switch turns the lights on

and off, regardless of the position of the

ignition switch^*1.

High Beams

Models with keyless access system

■ High beams

Push the lever forward until you hear a click.

■ Low beams

If you leave the power mode in VEHICLE OFF (LOCK)

while the lights are on, a chime sounds when the

driver’s door is opened.

When in high beams, pull the lever back to

return to low beams.

■ Flashing the high beams

Pull the lever back, and release it.

■ Lights off

Flashing the high beams

Low Beams

When the lights are on, the lights on indicator in the

instrument panel will be on.

2 Lights On Indicator P. 98

Turns on position, tail, and rear

licence plate lights

Turns on headlights, position,

tail, and rear licence plate lights

Do not leave the lights on when the engine is off

because it will cause the battery to discharge.

Turn the lever to OFF either when:

• The shift lever is in (P^*2.

• The parking brake is applied.

To turn the lights on again, turn the lever to

OFF to cancel the lights off mode. Even if you

do not cancel the lights off mode, the lights

come on automatically when:

• The shift lever is moved out of (P^*2.

• The parking brake is released.

• The vehicle starts to move.

If you sense that the level of the headlights is

abnormal, have your vehicle inspected by a dealer.

*1: Models with the keyless access system have an ENGINE START/STOP button instead of an ignition

switch.

*2: Continuously variable transmission models

170

18 FIT JAZZ-32T5A6100.book 171 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluLight Switches

1Automatic Operation (automatic lighting control)

Automatic Operation (automatic lighting control)

■

We recommend that you turn on the lights manually

when driving at night, in a dense fog, or in dark areas

such as long tunnels or parking facilities.

Automatic lighting control can be used when

the ignition switch is in ON (w^*1.

When the light switch is in AUTO, the

headlights and other exterior lights will switch

on and off automatically depending on the

ambient brightness.

The light sensor is in the location shown below.

Do not cover this light sensor with anything;

otherwise, the automatic lighting system may not

work properly.

Models with front sensor camera

Light Sensor

The headlights comes on when you unlock a door in dark areas with the headlight

switch in AUTO.

u Once you lock the door, the headlights will go off.

Automatic Lighting Off Feature

■

The headlights, all other exterior lights, and the instrument panel lights turn off 15

seconds after you remove the key or set the power mode to VEHICLE OFF (LOCK),

take the remote with you, and close the driver’s door.

Models without front sensor camera

Light Sensor

However, when the switch is in

, the position lights remain on.

If you turn the ignition switch to LOCK (0^*1with the headlight switch on, but do

not open the door, the lights turn off after 10 minutes (3 minutes, if the switch is in

the AUTO position).

The lights turn on again when you unlock or open the driver’s door. If you unlock

the door, but do not open it within 15 seconds, the lights go off. If you open the

driver’s door, you will hear a lights on reminder chime.

1Automatic Lighting Off Feature

You can change the headlight auto off timer setting.

2 Customized Features P. 131

*1: Models with the keyless access system have an ENGINE START/STOP button instead of an ignition switch.

171

18 FIT JAZZ-32T5A6100.book 172 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluFog Lights

Fog Lights

■ Front fog lights^*

Can be used when the position lights or the headlights are on.

■ Rear fog light

Can be used when the headlights or the front fog lights are on.

Front and Rear Fog Lights Switch^*

■

■ To turn the front fog lights on

Rotate the switch up from the OFF position to

the

position. The

indicator comes on.

■ To turn the front and rear fog lights on

Rotate the switch one position up from the

position. The

and

indicator comes on.

Front and Rear

Fog Lights Switch

■ To turn the rear fog light on

Rotate the switch down from the OFF

position. The

indicator comes on.

* Not available on all models

172

18 FIT JAZZ-32T5A6100.book 173 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluFog Lights

Rear Fog Lights^*

■

■ To turn the rear fog light on

Rotate the switch to . The

comes on.

indicator

Rear Fog Light Switch

* Not available on all models

173

18 FIT JAZZ-32T5A6100.book 174 ページ２０１７年８月２３日　水曜日　午前１１時２４分

*

uuOperating the Switches Around the Steering WheeluHeadlight Adjuster

Headlight Adjuster^*

*

You can adjust the vertical angle of the low

beam headlights when the ignition switch is in

ON (w^*1.

1Headlight Adjuster

Models with LED low beam headlights

Your vehicle is equipped with the automatic

headlight adjusting system that automatically adjusts

the vertical angle of the low beam headlights. If you

find a significant change in the vertical angle of the

headlights, there may be a problem with the system.

Have your vehicle checked by a dealer.

Turn the adjusting dial to select an

appropriate angle of the headlights.

The larger dial number indicates the lower

angle.

You may need to alter the headlight beam

distribution.

2 Adjusting Headlight Distribution P. 451

■ To select the adjusting dial position

Refer to the below table for the appropriate dial position for your vehicle's riding

and loading conditions.

Condition

Dial position

A driver

A driver and a front passenger

0

1

Five persons in the front and rear seats

Five persons in the front and rear seats and luggage in

the luggage area, within the limit of maximum

permissible axle weight and maximum permissible

vehicle weight

A driver and luggage in the luggage area, within the

limits of maximum permissible axle weight and

maximum permissible vehicle weight

2

3

*1: Models with the keyless access system have an ENGINE START/STOP button instead of an ignition

switch.

* Not available on all models

174

18 FIT JAZZ-32T5A6100.book 175 ページ２０１７年８月２３日　水曜日　午前１１時２４分

*

uuOperating the Switches Around the Steering WheeluAuto High-Beam (High Beam Support System)

Auto High-Beam (High Beam Support System)^*

*

Using a camera mounted to the inside of the windshield, this system detects light

sources ahead of the vehicle. Depending on the light source, the system

automatically switches the headlights to high beam for optimal visibility at night.

1Auto High-Beam (High Beam Support System)

The auto high-beam determines when to change the

headlight beams by responding to the brightness of

the lights ahead of your vehicle. In the following

cases, the system may not respond to the lights

properly:

The system operates when:

■The headlight switch is in AUTO.

• The brightness of the lights from the preceding or

oncoming vehicle is intense or poor.

• Visibility is poor due to the weather (rain, snow,

fog, windscreen frost, etc.).

■The lever is in the low beam position.

■The low beams are on and the system

recognizes that you are driving at night.

■The vehicle speed is above 40 km/h (25 mph).

• Other light sources, such as streetlights and electric

billboards are illuminating the road ahead.

• The brightness level of the road ahead constantly

changes.

• The road is bumpy or with many curves.

• A vehicle cuts in front of you, or a vehicle in front

of you is not in the preceding or oncoming

direction.

How it works

When the camera detects lights coming from a preceding or oncoming vehicle, the

headlights remain in low beam.

• Your vehicle is tilted with a heavy load in the rear.

When the camera detects no lights coming from a preceding or oncoming vehicle,

the headlights change to high beam.

If you find the timing of beam changes inconvenient

for driving, change the headlight beams manually.

The view angle or distance that the camera can detect lights ahead differs

depending on conditions, such as the brightness of the lights and the weather.

If you do not want the system to be activated at any

time when the headlight switch is in AUTO, consult a

dealer.

* Not available on all models

Continued

175

18 FIT JAZZ-32T5A6100.book 176 ページ２０１７年８月２３日　水曜日　午前１１時２４分

*

uuOperating the Switches Around the Steering WheeluAuto High-Beam (High Beam Support System)

1Operating the System

Operating the System

■

For the auto high-beam to work properly:

• Do not place an object that reflects light on the

dashboard.

• Keep the windscreen around the camera clean.

When cleaning the windscreen, be careful not to

apply the windscreen cleanser to the camera lens.

• Do not attach an object, sticker or film to the area

around the camera.

To activate the system, turn the headlight

switch to AUTO and then set the headlights

to low beam. The auto high-beam indicator

will come on.

2 Light Switches P. 170

• Do not touch the camera lens.

If the camera receives a strong impact, or repairing of

the area near the camera is required, consult a dealer.

Headlight Switch

To help reduce the likelihood that high interior

temperatures will cause the camera system to shut

off, when parking, find a shady area or face the front

of the vehicle away from the sun.

If you use a reflective sun shade, do not allow it to

cover the camera housing. Covering the camera can

concentrate heat on the camera.

The high beams remain on unless:

• You have been driving below 24km/h (15mph) for an extended amount of time.

• The speed of the vehicle drops below 10km/h (6mph).

• The windshield wipers have been running at a high speed for more than a few

seconds.

• You enter a well lit location.

If the

message appears:

The high beams come back on once the condition that caused them to turn off no

longer exists.

• Use the heating and cooling system^*/climate

control system^*to cool down the interior and, if

necessary, also use defroster mode with the air

flow directed towards the camera.

• Start driving the vehicle to lower the windscreen

temperature, which cools down the area around

the camera.

* Not available on all models

176

18 FIT JAZZ-32T5A6100.book 177 ページ２０１７年８月２３日　水曜日　午前１１時２４分

*

uuOperating the Switches Around the Steering WheeluAuto High-Beam (High Beam Support System)

If needed, you can temporarily turn the high beams off manually. Turn on the high

beams by pushing the lever forward until you hear a click, or flash the high beams

once by pulling the lever toward you. To turn the high beams back on, repeat one

of the procedures.

If you want the auto high-beam operation to resume at once, pull and hold the lever

towards you for a few seconds.

1Operating the System

If the

message appears:

• Park your vehicle in a safe place, and clean the

windscreen. If the message does not disappear

after you have cleaned the windscreen and driven

for a while, have your vehicle checked by a dealer.

177

18 FIT JAZZ-32T5A6100.book 178 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluDaytime Running Lights

Daytime Running Lights

The position^*/daytime running lights come on when the following conditions have

been met:

• The ignition switch is in ON (w^*1.

• The headlight switch is in AUTO.

Turning off the ignition switch or setting the power mode to VEHICLE OFF will turn

off the daytime running lights.

The daytime running lights are off once the headlight switch is turned on, or when

the head light switch is in AUTO and it is getting darker outside.

*1: Models with the keyless access system have an ENGINE START/STOP button instead of an ignition

switch.

* Not available on all models

178

18 FIT JAZZ-32T5A6100.book 179 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluWipers and Washers

Wipers and Washers

The windscreen wipers and washers can be

1Wipers and Washers

used when the ignition switch is in ON (w^*1.

NOTICE

Do not use the wipers when the windscreen is dry.

The windscreen will get scratched, or the rubber

blades will get damaged.

■ MIST

The wipers run at high speed until you release

the lever.

Pull to use

washer.

Turn the washers off if no washer fluid comes out.

The pump may get damaged.

■ Wiper switch (OFF, AUTO, LO, HI)

Change the wiper switch setting according to

the amount of rain.

The wiper motor may stop motor operation

temporarily to prevent an overload. Wiper operation

will return to normal within a few minutes, once the

circuit has returned to normal.

MIST

OFF

2 Automatic Intermittent Wipers P. 180

■ Washer

AUTO: Automatic

intermittent operation

LO: Low speed wipe

Sprays while you pull the lever toward you.

When you release the lever for more than one

second, the spray stops, the wipers sweep two

or three more times to clear the windscreen,

then stop.

NOTICE

In cold weather, the blades may freeze to the

windscreen, becoming stuck.

Operating the wipers in this condition may damage

the wipers. Use the demister to warm the

windscreen, then turn the wipers on.

HI: High speed wipe

If the wipers stop operating due to any obstacle such

as the build-up of snow, park the vehicle in a safe

place.

Rotate the wiper switch to OFF, and turn the ignition

switch to ACCESSORY (q or LOCK (0^*1, then

remove the obstacle.

*1: Models with the keyless access system have an ENGINE START/STOP button instead of an ignition

switch.

Continued

179

18 FIT JAZZ-32T5A6100.book 180 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluWipers and Washers

1Automatic Intermittent Wipers

Automatic Intermittent Wipers

■

The rainfall sensor is in the location shown below.

When you push the lever down to AUTO, the

windscreen wipers sweep once, and go into

the automatic mode.

Rainfall Sensor

The wipers operate intermittently, at low

speed, or at high speed and stops in

accordance with the amount of rainfall the

rainfall sensor detects.

Adjustment Ring

■ AUTO sensitivity adjustment

When the wiper function is set to AUTO, you

can adjust the sensitivity of the rain fall sensor

(using the adjustment ring) so that wipers will

operate in accordance with your preference.

AUTO should always be turned OFF before the

following situation in order to prevent severe damage

to the wiper system:

• Cleaning the windshield

• Driving through a car wash

• No rain present

Sensor sensitivity

Low sensitivity

High sensitivity

180

18 FIT JAZZ-32T5A6100.book 181 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluWipers and Washers

Rear Wiper/Washer

■

The rear wiper and washer can be used when

the ignition switch is in ON (w^*1.

■ Wiper switch (OFF, INT, ON)

Change the wiper switch setting according to

the amount of rain.

■ Washer (

)

Sprays while you rotate the switch to this

position.

Hold it to activate the wiper and to spray the

washer. Once released, it stops operating

after a few more sweeps.

INT: Intermittent

ON

OFF

Washer

■ Operating in reverse

When you shift the transmission to (R with the windscreen wipers activated, the

rear wiper operates automatically as follows even if its switch is off.

Front Wiper Position

Rear Wiper Operation

AUTO (Intermittent)

Intermittent

LO (Low speed wipe)

HI (High speed wipe)

Continuous

*1: Models with the keyless access system have an ENGINE START/STOP button instead of an ignition

switch.

181

18 FIT JAZZ-32T5A6100.book 182 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluBrightness Control

Brightness Control

When the ignition switch is in ON (w^*1, you

1Brightness Control

can use the

instrument panel brightness.

Brighten: Turn the knob to the right.

Dim: Turn the knob to the left.

(Select/Reset) knob to adjust

Instrument panel brightness varies, depending on

whether the exterior lights are on or off. The

instrument panel dims to reduce glare when they are

on.

To cancels the reduced instrument panel brightness

when the exterior lights are on, turn the knob to the

right until the brightness display is up to max, the

beeper sounds.

You will hear a beeper when the brightness

reaches minimum or maximum. Several

seconds after you have adjusted the

brightness, you will be returned to the

previous screen.

(Select/Reset) Knob

The brightness can be set differently for when the

exterior lights are on, and when they are off.

■ Brightness level indicator

The brightness level is shown on the multi-

information display while you are adjusting it.

*1: Models with the keyless access system have an ENGINE START/STOP button instead of an ignition

switch.

182

18 FIT JAZZ-32T5A6100.book 183 ページ２０１７年８月２３日　水曜日　午前１１時２４分

*

uuOperating the Switches Around the Steering WheeluRear Demister/Heated Door Mirror

Rear Demister/Heated Door Mirror^*

*

Press the rear demister and heated door mirror button or touch the icon to defog

the rear window and mirrors when the ignition switch is in ON (w^*1.

1Rear Demister/Heated Door Mirror

NOTICE

When cleaning the inside of the rear window, be

careful not to damage the heating wires.

It is critical to wipe the window from side to side

along the demister heating wires.

Models with heating and cooling system

This system consumes a lot of power, so turn it off

when the window has been demisted or deiced.

Also, do not use the system for a long period when

the engine is idling. This may weaken the battery,

making it difficult to start the engine.

Models with climate control system

The rear demister and heated door mirrors

automatically switch off after 10-30 minutes

depending on the outside temperature.

However, if the outside temperature is 0°C or

below, they do not automatically switch off.

*1: Models with the keyless access system have an ENGINE START/STOP button instead of an ignition

switch.

* Not available on all models

183

18 FIT JAZZ-32T5A6100.book 184 ページ２０１７年８月２３日　水曜日　午前１１時２４分

uuOperating the Switches Around the Steering WheeluAdjusting the Steering Wheel

Adjusting the Steering Wheel

The steering wheel height and distance from your body can be adjusted so that you

can comfortably grip the steering wheel in an appropriate driving posture.

1. Pull the steering wheel adjustment lever up.

1Adjusting the Steering Wheel

3

WARNING

u The steering wheel adjustment lever is

Adjusting the steering wheel position while

driving may cause you to lose control of the

vehicle and be seriously injured in a crash.

To adjust

under the steering column.

2. Move the steering wheel up or down, and

in or out.

Adjust the steering wheel only when the

vehicle is stopped.

To lock

u Make sure you can see the instrument

panel gauges and indicators.

Lever

Height and Distance

3. Push the steering wheel adjustment lever

down to lock the steering wheel in position.

u After adjusting the position, make sure

you have securely locked the steering

wheel in place by trying to move it up,

down, in, and out.

184

Controls -> Operating the Switches Around the Steering Wheel for Your Honda Jazz 4 Door Third Generation (2016-2020)

Related Topics

Popular Owner Manuals

Latest Owner Manuals