2009-2015 Hyundai Ix35 SUV Maintenance User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Maintenance for Your Hyundai Ix35 SUV First Generation (2009-2015)

Engine compartment / 7-2  
Maintenance services / 7-3  
Owner maintenance / 7-4  
Scheduled maintenance service / 7-6  
Explanation of scheduled maintenance items / 7-18  
Engine oil / 7-21  
Engine coolant / 7-22  
Brake/clutch fluid / 7-25  
Washer fluid / 7-26  
Parking brake / 7-27  
Air cleaner / 7-28  
Climate control air filter / 7-29  
Wiper blades / 7-31  
Battery / 7-34  
Tires and wheels / 7-37  
Fuses / 7-50  
Light bulbs / 7-59  
Maintenance  
7
Appearance care / 7-66  
Emission control system / 7-72  
California perchlorate notice / 7-75  
Maintenance  
ENGINE COMPARTMENT  
1. Engine coolant reservoir  
2. Engine oil filler cap  
3. Brake/Clutch* fluid reservoir  
4. Air cleaner  
5. Fuse box  
6. Negative battery terminal  
7. Positive battery terminal  
8. Radiator cap  
9. Engine oil dipstick  
10. Windshield washer fluid reservoir  
* : if equipped  
* The actual engine room in the vehicle may differ from the illustration.  
OLM079001  
7 2  
Maintenance  
MAINTENANCE SERVICES  
You should exercise the utmost care to  
prevent damage to your vehicle and  
injury to yourself whenever performing  
any maintenance or inspection proce-  
dures.  
Owner’s responsibility  
Owner maintenance precautions  
Improper or incomplete service may  
result in problems. This section gives  
instructions only for the maintenance  
items that are easy to perform.  
✽
NOTICE  
Maintenance Service and Record  
Retention are the owner's responsibility.  
Should you have any doubts concerning  
the inspection or servicing of your vehi-  
cle, we strongly recommend that you  
have an authorized HYUNDAI dealer  
perform this work.  
As explained earlier in this section, sev-  
eral procedures can be done only by an  
authorized HYUNDAI dealer with special  
tools.  
You should retain documents that show  
proper maintenance has been performed  
on your vehicle in accordance with the  
scheduled maintenance service charts  
shown on the following pages. You need  
this information to establish your compli-  
ance with the servicing and maintenance  
requirements of your vehicle warranties.  
An authorized HYUNDAI dealer has fac-  
tory-trained technicians and genuine  
HYUNDAI parts to service your vehicle  
properly. For expert advice and quality  
service, see an authorized HYUNDAI  
dealer.  
✽
NOTICE  
Improper owner maintenance during the  
warranty period may affect warranty  
coverage. For details, read the separate  
Detailed warranty information is provided  
in your Owner’s Handbook & Warranty  
Information booklet.  
Owner’s Handbook  
&
Warranty  
Information booklet provided with the  
vehicle. If you're unsure about any serv-  
icing or maintenance procedure, have it  
done by an authorized HYUNDAI dealer.  
Inadequate, incomplete or insufficient  
servicing may result in operational prob-  
lems with your vehicle that could lead to  
vehicle damage, an accident, or person-  
al injury.  
Repairs and adjustments required as a  
result of improper maintenance or a lack  
of required maintenance are not covered.  
We recommend you have your vehicle  
maintained and repaired by an author-  
ized HYUNDAI dealer. An authorized  
HYUNDAI dealer meets HYUNDAI’s high  
service quality standards and receives  
technical support from HYUNDAI in  
order to provide you with a high level of  
service satisfaction.  
7 3  
Maintenance  
OWNER MAINTENANCE  
The following lists are vehicle checks and  
inspections that should be performed by  
the owner or an authorized HYUNDAI  
dealer at the frequencies indicated to  
help ensure safe, dependable operation  
of your vehicle.  
Owner maintenance schedule  
WARNING - Maintenance  
work  
When you stop for fuel:  
• Check the engine oil level.  
• Performing maintenance work on  
a vehicle can be dangerous. You  
can be seriously injured while  
performing some maintenance  
procedures. If you lack sufficient  
knowledge and experience or the  
proper tools and equipment to do  
the work, have it done by an  
authorized HYUNDAI dealer.  
• Check the coolant level in coolant  
reservoir.  
• Check the windshield washer fluid  
level.  
• Look for low or under-inflated tires.  
Any adverse conditions should be  
brought to the attention of your dealer as  
soon as possible.  
These Owner Maintenance Checks are  
generally not covered by warranties and  
you may be charged for labor, parts and  
lubricants used.  
WARNING  
Be careful when checking your  
engine coolant level when the  
engine is hot. Scalding hot coolant  
and steam may blow out under  
pressure. This could cause burns  
or other serious injury.  
• Working under the hood with the  
engine running is dangerous. It  
becomes even more dangerous  
when you wear jewelry or loose  
clothing. These can become  
entangled in moving parts and  
result in injury. Therefore, if you  
must run the engine while work-  
ing under the hood, make certain  
that you remove all jewelry (espe-  
cially rings, bracelets, watches,  
and necklaces) and all neckties,  
scarves, and similar loose cloth-  
ing before getting near the  
engine or cooling fans.  
7 4  
Maintenance  
While operating your vehicle:  
At least monthly:  
• Check the coolant level in the engine  
coolant reservoir.  
At least once a year:  
• Clean the body and door drain holes.  
• Note any changes in the sound of the  
exhaust or any smell of exhaust fumes  
in the vehicle.  
• Lubricate the door hinges and checks,  
and hood hinges.  
• Check the operation of all exterior  
lights, including the stoplights, turn sig-  
nals and hazard warning flashers.  
• Check for vibrations in the steering  
wheel. Notice any increased steering  
effort or looseness in the steering  
wheel, or change in its straight-ahead  
position.  
• Lubricate the door and hood locks and  
latches.  
• Check the inflation pressures of all  
tires including the spare.  
• Lubricate the door rubber weather-  
strips.  
• Check the air conditioning system.  
• Notice if your vehicle constantly turns  
slightly or “pulls” to one side when trav-  
eling on smooth, level road.  
At least twice a year  
(i.e., every Spring and Fall):  
• Inspect and lubricate the automatic  
transaxle linkage and controls.  
• Check the radiator, heater and air con-  
ditioning hoses for leaks or damage.  
• Clean the battery and terminals.  
• Check the brake/clutch* fluid level.  
* : if equipped  
• When stopping, listen and check for  
unusual sounds, pulling to one side,  
increased brake pedal travel or “hard-  
to-push” brake pedal.  
• Check the windshield washer spray  
and wiper operation. Clean the wiper  
blades with clean cloth dampened with  
washer fluid.  
• If any slipping or changes in the oper-  
ation of your transaxle occurs, check  
the transaxle fluid level.  
• Check the headlight alignment.  
• Check the muffler, exhaust pipes,  
shields and clamps.  
• Check the automatic transaxle P  
(Park) function.  
• Check the parking brake.  
• Check the lap/shoulder belts for wear  
and function.  
• Check for fluid leaks under your vehicle  
(water dripping from the air condition-  
ing system during or after use is nor-  
mal).  
• Check for worn tires and loose wheel  
lug nuts.  
7 5  
Maintenance  
SCHEDULED MAINTENANCE SERVICE  
Follow Normal Maintenance Schedule if  
the vehicle is usually operated where  
none of the following conditions apply. If  
any of the following conditions apply, fol-  
low Maintenance Under Severe Usage  
Conditions.  
If your vehicle is operated under the  
above conditions, you should inspect,  
replace or refill more frequently than the  
following Normal Maintenance Schedule.  
After 120 months or 150,000 miles  
(240,000 km) continue to follow the pre-  
scribed maintenance intervals.  
• Repeated short distance driving.  
• Driving in dusty conditions or sandy  
areas.  
• Extensive use of brakes.  
• Driving in areas where salt or other  
corrosive materials are being used.  
• Driving on rough or muddy roads.  
• Driving in mountainous areas.  
• Extended periods of idling or low  
speed operation.  
• Driving for a prolonged period in cold  
temperatures and/or extremely humid  
climates.  
• More than 50% driving in heavy city  
traffic during hot weather above 90°F  
(32°C).  
7 6  
Maintenance  
NORMAL MAINTENANCE SCHEDULE  
The following maintenance services must be performed to ensure good emission control and performance. Keep receipts for all  
vehicle emission services to protect your warranty. Where both mileage and time are shown, the frequency of service is deter-  
mined by whichever occurs first.  
7,500 miles (12,000 km) or 6 months  
❑ Inspect air cleaner filter  
22,500 miles (36,000 km) or 18 months  
❑ Inspect air cleaner filter  
❑ Inspect vacuum hose  
❑ Inspect vacuum hose  
❑ Replace engine oil and filter  
(7,500 miles (12,000 km) or 12 months)  
❑ Replace engine oil and filter  
(22,500 miles (36,000 km) or 36 months)  
15,000 miles (24,000 km) or 12 months  
❑ Inspect air cleaner filter  
❑ Inspect vacuum hose  
❑ Inspect air conditioning refrigerant  
❑ Inspect brake hoses and lines  
❑ Inspect drive shafts and boots  
❑ Inspect electronic throttle control  
❑ Inspect exhaust pipe and muffler  
❑ Inspect front brake disc/pads, calipers  
❑ Inspect propeller shaft (AWD)  
❑ Inspect rear brake disc/pads  
❑ Inspect steering gear box, linkage & boots/lower arm ball joint,  
upper arm ball joint  
❑ Inspect suspension mounting bolts  
❑ Replace climate control air filter (for evaporator and blower unit)  
❑ Replace engine oil and filter  
(15,000 miles (24,000 km) or 24 months)  
7 7  
Maintenance  
NORMAL MAINTENANCE SCHEDULE (CONT.)  
37,500 miles (60,000 km) or 30 months  
❑ Inspect air cleaner filter  
30,000 miles (48,000 km) or 24 months  
❑ Inspect vacuum hose  
❑ Inspect vacuum hose  
❑ Inspect air conditioning refrigerant  
❑ Inspect brake hoses and lines  
❑ Inspect drive shafts and boots  
❑ Inspect electronic throttle control  
❑ Inspect exhaust pipe and muffler  
❑ Inspect front brake disc/pads, calipers  
❑ Inspect propeller shaft (AWD)  
❑ Inspect rear brake disc/pads  
❑ Inspect manual transaxle fluid (if equipped)  
❑ Inspect rear axle oil (AWD) *2  
❑ Inspect transfer case oil (AWD) *2  
❑ Replace engine oil and filter  
(37,500 miles (60,000 km) or 60 months)  
*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but peri-  
odic inspection is recommended for this maintenance schedule depends on  
fuel quality. If there are some important safety matters like fuel flow restric-  
tion, surging, loss of power, hard starting problem etc, replace the fuel filter  
immediately regardless of maintenance schedule and consult an authorized  
HYUNDAI dealer for details.  
❑ Inspect steering gear box, linkage & boots/lower arm ball joint,  
upper arm ball joint  
❑ Inspect suspension mounting bolts  
❑ Inspect brake/clutch (if equipped) fluid  
❑ Inspect fuel filter *1  
*2 : Transfer case oil and rear axle oil should be changed anytime they have been  
submerged in water.  
❑ Inspect fuel lines, fuel hoses and connections  
❑ Inspect fuel tank air filter (if equipped) *1  
❑ Inspect parking brake  
❑ Inspect vapor hose and fuel filler cap, fuel tank  
❑ Replace climate control air filter (for evaporator and blower unit)  
❑ Replace air cleaner filter  
❑ Replace engine oil and filter  
(30,000 miles (48,000 km) or 48 months)  
7 8  
Maintenance  
NORMAL MAINTENANCE SCHEDULE (CONT.)  
45,000 miles (72,000 km) or 36 months  
52,500 miles (84,000 km) or 42 months  
❑ Inspect air cleaner filter  
❑ Inspect air cleaner filter  
❑ Inspect vacuum hose  
❑ Inspect vacuum hose  
❑ Inspect air conditioning refrigerant  
❑ Inspect brake hoses and lines  
❑ Inspect drive shafts and boots  
❑ Inspect electronic throttle control  
❑ Inspect exhaust pipe and muffler  
❑ Inspect front brake disc/pads, calipers  
❑ Inspect propeller shaft (AWD)  
❑ Inspect rear brake disc/pads  
❑ Replace engine oil and filter  
(52,500 miles (84,000 km) or 84 months)  
❑ Inspect steering gear box, linkage & boots/lower arm ball joint,  
upper arm ball joint  
❑ Inspect suspension mounting bolts  
❑ Replace climate control air filter (for evaporator and blower unit)  
❑ Replace engine oil and filter  
(45,000 miles (72,000 km) or 72 months)  
7 9  
Maintenance  
NORMAL MAINTENANCE SCHEDULE (CONT.)  
60,000 miles (96,000 km) or 48 months  
67,500 miles (108,000 km) or 54 months  
❑ Inspect air cleaner filter  
❑ Inspect vacuum hose  
❑ Inspect air conditioning refrigerant  
❑ Inspect brake hoses and lines  
❑ Inspect drive shafts and boots  
❑ Inspect electronic throttle control  
❑ Inspect exhaust pipe and muffler  
❑ Inspect front brake disc/pads, calipers  
❑ Inspect propeller shaft (AWD)  
❑ Inspect rear brake disc/pads  
❑ Inspect vacuum hose  
❑ Replace engine oil and filter  
(67,500 miles (108,000 km) or 108 months)  
*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but  
periodic inspection is recommended for this maintenance schedule depends  
on fuel quality. If there are some important safety matters like fuel flow  
restriction, surging, loss of power, hard starting problem etc, replace the fuel  
filter immediately regardless of maintenance schedule and consult an  
authorized HYUNDAI dealer for details.  
*3 : Inspect for excessive tappet noise and/or engine vibration and adjust if nec-  
essary.  
*4 : The drive belt should be replaced when cracks occur or tension is reduced  
excessively.  
❑ Inspect steering gear box, linkage & boots/lower arm ball joint,  
upper arm ball joint  
❑ Inspect suspension mounting bolts  
❑ Inspect brake/clutch (if equipped) fluid  
❑ Inspect fuel filter *1  
❑ Inspect fuel lines, fuel hoses and connections  
❑ Inspect fuel tank air filter (if equipped) *1  
❑ Inspect parking brake  
❑ Inspect vapor hose and fuel filler cap, fuel tank  
❑ Inspect valve clearance *3  
❑ Inspect drive belts  
(First, 60,000 miles (96,000 km) or 72 months  
after every 15,000 miles (24,000 km) or 24 months) *4  
❑ Replace climate control air filter (for evaporator and blower unit)  
❑ Replace air cleaner filter  
❑ Replace engine oil and filter  
(60,000 miles (96,000 km) or 96 months)  
7 10  
Maintenance  
NORMAL MAINTENANCE SCHEDULE (CONT.)  
75,000 miles (120,000 km) or 60 months  
82,500 miles (132,000 km) or 66 months  
❑ Inspect air cleaner filter  
❑ Inspect air cleaner filter  
❑ Inspect vacuum hose  
❑ Inspect vacuum hose  
❑ Inspect air conditioning refrigerant  
❑ Inspect brake hoses and lines  
❑ Inspect drive shafts and boots  
❑ Inspect electronic throttle control  
❑ Inspect exhaust pipe and muffler  
❑ Inspect front brake disc/pads, calipers  
❑ Inspect propeller shaft (AWD)  
❑ Inspect rear brake disc/pads  
❑ Replace engine oil and filter  
(82,500 miles (132,000 km) or 132 months)  
❑ Inspect steering gear box, linkage & boots/lower arm ball joint,  
upper arm ball joint  
❑ Inspect suspension mounting bolts  
❑ Inspect manual transaxle fluid (if equipped)  
❑ Inspect rear axle oil (AWD) *2  
❑ Inspect transfer case oil (AWD) *2  
❑ Inspect drive belts  
(First, 60,000 miles (96,000 km) or 72 months  
after every 15,000 miles (24,000 km) or 24 months)*4  
❑ Replace climate control air filter (for evaporator and blower unit)  
❑ Replace engine oil and filter  
(75,000 miles (120,000 km) or 120 months)  
*2 : Transfer case oil and rear axle oil should be changed anytime they have been  
submerged in water.  
*4 : The drive belt should be replaced when cracks occur or tension is reduced  
excessively.  
7 11  
Maintenance  
NORMAL MAINTENANCE SCHEDULE (CONT.)  
90,000 miles (144,000 km) or 72 months  
97,500 miles (156,000 km) or 78 months  
❑ Inspect air cleaner filter  
❑ Inspect vacuum hose  
❑ Inspect air conditioning refrigerant  
❑ Inspect brake hoses and lines  
❑ Inspect drive shafts and boots  
❑ Inspect electronic throttle control  
❑ Inspect exhaust pipe and muffler  
❑ Inspect front brake disc/pads, calipers  
❑ Inspect propeller shaft (AWD)  
❑ Inspect rear brake disc/pads  
❑ Inspect vacuum hose  
❑ Replace engine oil and filter  
(97,500 miles (156,000 km) or 156 months)  
*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but  
periodic inspection is recommended for this maintenance schedule depends  
on fuel quality. If there are some important safety matters like fuel flow  
restriction, surging, loss of power, hard starting problem etc, replace the fuel  
filter immediately regardless of maintenance schedule and consult an author-  
ized HYUNDAI dealer for details.  
*4 : The drive belt should be replaced when cracks occur or tension is reduced  
excessively.  
❑ Inspect steering gear box, linkage & boots/lower arm ball joint,  
upper arm ball joint  
❑ Inspect suspension mounting bolts  
❑ Inspect brake/clutch (if equipped) fluid  
❑ Inspect fuel filter *1  
❑ Inspect fuel lines, fuel hoses and connections  
❑ Inspect fuel tank air filter (if equipped) *1  
❑ Inspect parking brake  
❑ Inspect vapor hose and fuel filler cap, fuel tank  
❑ Inspect drive belts  
(First, 60,000 miles (96,000 km) or 72 months  
after every 15,000 miles (24,000 km) or 24 months)*4  
❑ Replace climate control air filter (for evaporator and blower unit)  
❑ Replace air cleaner filter  
❑ Replace engine oil and filter  
(90,000 miles (144,000 km) or 144 months)  
7 12  
Maintenance  
NORMAL MAINTENANCE SCHEDULE (CONT.)  
105,000 miles (168,000 km) or 84 months  
112,500 miles (180,000 km) or 90 months  
❑ Inspect air cleaner filter  
❑ Inspect air cleaner filter  
❑ Inspect vacuum hose  
❑ Inspect vacuum hose  
❑ Inspect air conditioning refrigerant  
❑ Inspect brake hoses and lines  
❑ Inspect drive shafts and boots  
❑ Inspect electronic throttle control  
❑ Inspect exhaust pipe and muffler  
❑ Inspect front brake disc/pads, calipers  
❑ Inspect propeller shaft (AWD)  
❑ Inspect rear brake disc/pads  
❑ Inspect manual transaxle fluid (if equipped)  
❑ Inspect rear axle oil (AWD) *2  
❑ Inspect transfer case oil (AWD) *2  
❑ Replace engine oil and filter  
(112,500 miles (180,000 km) or 180 months)  
*2 : Transfer case oil and rear axle oil should be changed anytime they have been  
submerged in water.  
*4 : The drive belt should be replaced when cracks occur or tension is reduced  
excessively.  
❑ Inspect steering gear box, linkage & boots/lower arm ball joint,  
upper arm ball joint  
❑ Inspect suspension mounting bolts  
❑ Inspect drive belts  
(First, 60,000 miles (96,000 km) or 72 months  
after every 15,000 miles (24,000 km) or 24 months) *4  
❑ Replace climate control air filter (for evaporator and blower unit)  
❑ Replace spark plugs (iridium coated)  
❑ Replace engine oil and filter  
(105,000 miles (168,000 km) or 168 months)  
7 13  
Maintenance  
NORMAL MAINTENANCE SCHEDULE (CONT.)  
120,000 miles (192,000 km) or 96 months  
127,500 miles (204,000 km) or 102 months  
❑ Inspect air cleaner filter  
❑ Inspect vacuum hose  
❑ Inspect air conditioning refrigerant  
❑ Inspect brake hoses and lines  
❑ Inspect drive shafts and boots  
❑ Inspect electronic throttle control  
❑ Inspect exhaust pipe and muffler  
❑ Inspect front brake disc/pads, calipers  
❑ Inspect propeller shaft (AWD)  
❑ Inspect vacuum hose  
❑ Replace engine oil and filter  
(127,500 miles (204,000 km) or 204 months)  
*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but  
periodic inspection is recommended for this maintenance schedule depends  
on fuel quality. If there are some important safety matters like fuel flow  
restriction, surging, loss of power, hard starting problem etc, replace the fuel  
filter immediately regardless of maintenance schedule and consult an  
authorized HYUNDAI dealer for details.  
*3 : Inspect for excessive tappet noise and/or engine vibration and adjust if nec-  
essary.  
*4 : The drive belt should be replaced when cracks occur or tension is reduced  
excessively.  
❑ Inspect rear brake disc/pads  
❑ Inspect steering gear box, linkage & boots/lower arm ball joint,  
upper arm ball joint  
❑ Inspect suspension mounting bolts  
❑ Inspect brake/clutch (if equipped) fluid  
❑ Inspect fuel filter *1  
❑ Inspect fuel lines, fuel hoses and connections  
❑ Inspect fuel tank air filter (if equipped) *1  
❑ Inspect parking brake  
❑ Inspect vapor hose and fuel filler cap, fuel tank  
❑ Inspect valve clearance *3  
❑ Inspect drive belts  
(First, 60,000 miles (96,000 km) or 72 months  
after every 15,000 miles (24,000 km) or 24 months)*4  
❑ Replace climate control air filter (for evaporator and blower unit)  
❑ Replace air cleaner filter  
❑ Replace engine oil and filter  
(120,000 miles (192,000 km) or 192 months)  
❑ Replace coolant (First, 120,000 miles (192,000 km) or 120 months  
after every 30,000 miles (48,000 km) or 24 months)  
7 14  
Maintenance  
NORMAL MAINTENANCE SCHEDULE (CONT.)  
135,000 miles (216,000 km) or 108 months  
142,500 miles (228,000 km) or 114 months  
❑ Inspect air cleaner filter  
❑ Inspect air cleaner filter  
❑ Inspect vacuum hose  
❑ Inspect vacuum hose  
❑ Inspect air conditioning refrigerant  
❑ Inspect brake hoses and lines  
❑ Inspect drive shafts and boots  
❑ Inspect electronic throttle control  
❑ Inspect exhaust pipe and muffler  
❑ Inspect front brake disc/pads, calipers  
❑ Inspect propeller shaft (AWD)  
❑ Inspect rear brake disc/pads  
❑ Replace engine oil and filter  
(142,500 miles (228,000 km) or 228 months)  
*4 : The drive belt should be replaced when cracks occur or tension is reduced  
excessively.  
❑ Inspect steering gear box, linkage & boots/lower arm ball joint,  
upper arm ball joint  
❑ Inspect suspension mounting bolts  
❑ Inspect drive belts  
(First, 60,000 miles (96,000 km) or 72 months  
after every 15,000 miles (24,000 km) or 24 months)*4  
❑ Replace climate control air filter (for evaporator and blower unit)  
❑ Replace engine oil and filter  
(135,000 miles (216,000 km) or 216 months)  
7 15  
Maintenance  
NORMAL MAINTENANCE SCHEDULE (CONT.)  
150,000 miles (240,000 km) or 120 months  
(Continued)  
❑ Replace climate control air filter (for evaporator and blower unit)  
❑ Replace air cleaner filter  
❑ Inspect vacuum hose  
❑ Inspect air conditioning refrigerant  
❑ Inspect brake hoses and lines  
❑ Inspect drive shafts and boots  
❑ Inspect electronic throttle control  
❑ Inspect exhaust pipe and muffler  
❑ Inspect front brake disc/pads, calipers  
❑ Inspect propeller shaft (AWD)  
❑ Inspect rear brake disc/pads  
❑ Replace engine oil and filter  
(150,000 miles (240,000 km) or 240 months)  
❑ Replace coolant (First, 120,000 miles (192,000 km) or 120 months  
after every 30,000 miles (48,000 km) or 24 months)  
No check, No service required  
❑ Inspect steering gear box, linkage & boots/lower arm ball joint,  
upper arm ball joint  
❑ Automatic transaxle fluid (if equipped)  
*1 : Fuel filter & Fuel tank air filter are considered to be maintenance free but  
periodic inspection is recommended for this maintenance schedule depends  
on fuel quality. If there are some important safety matters like fuel flow  
restriction, surging, loss of power, hard starting problem etc, replace the fuel  
filter immediately regardless of maintenance schedule and consult an  
authorized HYUNDAI dealer for details.  
❑ Inspect suspension mounting bolts  
❑ Inspect brake/clutch (if equipped) fluid  
❑ Inspect fuel filter *1  
❑ Inspect fuel lines, fuel hoses and connections  
❑ Inspect fuel tank air filter (if equipped) *1  
❑ Inspect parking brake  
*2 : Transfer case oil and rear axle oil should be changed anytime they have been  
submerged in water.  
*4 : The drive belt should be replaced when cracks occur or tension is reduced  
excessively.  
❑ Inspect vapor hose and fuel filler cap, fuel tank  
❑ Inspect manual transaxle fluid (if equipped)  
❑ Inspect rear axle oil (AWD) *2  
❑ Inspect transfer case oil (AWD) *2  
❑ Inspect drive belts  
(First, 60,000 miles (96,000 km) or 72 months  
after every 15,000 miles (24,000 km) or 24 months)*4  
(Continued)  
7 16  
Maintenance  
MAINTENANCE UNDER SEVERE USAGE CONDITIONS  
The following items must be serviced more frequently on cars normally used under severe driving conditions. Refer to the chart  
below for the appropriate maintenance intervals.  
R : Replace  
I : Inspect and, after inspection, clean, adjust, repair or replace if necessary  
MAINTENANCE  
OPERATION  
MAINTENANCE ITEM  
MAINTENANCE INTERVALS  
DRIVING CONDITION  
ENGINE OIL AND FILTER  
AIR CLEANER FILTER  
R
R
R
R
R
I
EVERY 3,750 MILES (6,000 KM) OR 6 MONTHS  
MORE FREQUENTLY  
A, B, C, D, E, F, G, H, I, K  
C, E  
SPARK PLUGS  
MORE FREQUENTLY  
B, H  
AUTOMATIC TRANSAXLE FLUID  
MANUAL TRANSAXLE FLUID  
FRONT BRAKE DISC/PADS, CALIPERS  
REAR BRAKE DISC /PADS  
PARKING BRAKE  
EVERY 60,000 MILES (96,000 KM)  
EVERY 75,000 MILES (120,000 KM)  
MORE FREQUENTLY  
A, C, E, F, G, I  
A, C, E, F, G, I  
C, D, G, H  
I
MORE FREQUENTLY  
C, D, G, H  
I
MORE FREQUENTLY  
C, D, G, H  
STEERING GEAR BOX, LINKAGE & BOOTS/  
LOWER ARM BALL JOINT, UPPER ARM BALL JOINT  
I
MORE FREQUENTLY  
C, D, E, F, G, H, I  
DRIVE SHAFTS AND BOOTS  
TRANSFER CASE OIL (AWD)  
REAR AXLE OIL (AWD)  
I
EVERY 7,500 MILES (12,000 KM) OR 6 MONTHS  
EVERY 75,000 MILES (120,000 KM)  
C, D, E, F, G, H, I, J  
C, D, E, G, H, I, J  
C, D, E, G, H, I, J  
R
R
EVERY 75,000 MILES (120,000 KM)  
CLIMATE CONTROL AIR FILTER  
(FOR EVAPORATOR AND BLOWER UNIT)  
R
I
MORE FREQUENTLY  
C, E  
C, E  
PROPELLER SHAFT  
EVERY 7,500 MILES (12,000 KM) OR 6 MONTHS  
SEVERE DRIVING CONDITIONS  
A - Repeatedly driving short distance of less than 5 miles (8 km) in normal tem-  
perature or less than 10 miles (16 km) in freezing temperature  
B - Extensive engine idling or low speed driving for long distances  
C - Driving on rough, dusty, muddy, unpaved, graveled or salt- spread roads  
D - Driving in areas using salt or other corrosive materials or in very cold weather  
E - Driving in sandy areas  
F - Driving in heavy traffic area over 90°F (32°C)  
G - Driving on uphill, downhill, or mountain road  
H - Towing a Trailer, or using a camper, or roof rack  
I - Driving as a patrol car, taxi, other commercial use or vehicle towing  
J - Driving over 106 mph (170 km/h)  
K - Frequently driving in stop-and-go conditions  
7 17  
Maintenance  
EXPLANATION OF SCHEDULED MAINTENANCE ITEMS  
Engine oil and filter  
Fuel filter (cartridge)  
Fuel lines, fuel hoses and con-  
nections  
The engine oil and filter should be  
changed at the intervals specified in the  
maintenance schedule. If the vehicle is  
being driven in severe conditions, more  
frequent oil and filter changes are  
required.  
A clogged filter can limit the speed at  
which the vehicle may be driven, damage  
the emission system and cause multiple  
issues such as hard starting. If an exces-  
sive amount of foreign matter accumu-  
lates in the fuel tank, the filter may  
require replacement more frequently.  
Check the fuel lines, fuel hoses and con-  
nections for leakage and damage. Have  
an authorized HYUNDAI dealer replace  
any damaged or leaking parts immedi-  
ately.  
After installing a new filter, run the engine  
for several minutes, and check for leaks  
at the connections. Fuel filters should be  
installed by an authorized HYUNDAI  
dealer.  
Drive belts  
Vapor hose and fuel filler cap  
Inspect all drive belts for evidence of  
cuts, cracks, excessive wear or oil satu-  
ration and replace if necessary. Drive  
belts should be checked periodically for  
proper tension and adjusted as neces-  
sary.  
The vapor hose and fuel filler cap should  
be inspected at those intervals specified  
in the maintenance schedule. Make sure  
that a new vapor hose or fuel filler cap is  
correctly replaced.  
7 18  
Maintenance  
Vacuum crankcase ventilation  
hoses  
Air cleaner filter  
Coolant  
A Genuine HYUNDAI air cleaner filter is  
recommended when the filter is  
replaced.  
The coolant should be changed at the  
intervals specified in the maintenance  
schedule.  
Inspect the surface of hoses for evidence  
of heat and/or mechanical damage. Hard  
and brittle rubber, cracking, tears, cuts,  
abrasions, and excessive swelling indi-  
cate deterioration. Particular attention  
should be paid to examine those hose  
surfaces nearest to high heat sources,  
such as the exhaust manifold.  
Manual transaxle fluid  
(if equipped)  
Spark plugs  
Make sure to install new spark plugs of  
the correct heat range.  
Inspect the manual transaxle fluid  
according to the maintenance schedule.  
Valve clearance  
Inspect the hose routing to assure that  
the hoses do not come in contact with  
any heat source, sharp edges or moving  
component which might cause heat dam-  
age or mechanical wear. Inspect all hose  
connections, such as clamps and cou-  
plings, to make sure they are secure, and  
that no leaks are present. Hoses should  
be replaced immediately if there is any  
evidence of deterioration or damage.  
Automatic transaxle fluid  
(if equipped)  
Inspect for excessive valve noise and/or  
engine vibration and adjust if necessary.  
An authorized HYUNDAI dealer should  
perform the operation.  
Automatic transaxle fluid should not be  
checked under normal usage conditions.  
But in severe conditions, the fluid should  
be changed at an authorized HYUNDAI  
dealer in accordance to the scheduled  
maintenance at the beginning of this  
chapter.  
Cooling system  
Check for cooling system components,  
such as radiator, coolant reservoir, hoses  
and connections for leakage and dam-  
age. Replace any damaged parts.  
✽
NOTICE  
Automatic transaxle fluid color is basi-  
cally red.  
As the vehicle is driven, the automatic  
transaxle fluid will begin to look darker.  
It is normal condition and you should  
not judge the need to replace the fluid  
based upon the changed color.  
7 19  
Maintenance  
Parking brake  
Steering gear box, linkage &  
boots/lower arm ball joint  
CAUTION  
Inspect the parking brake system includ-  
ing the parking brake pedal and cables.  
The use of a non-specified fluid  
could result in transaxle malfunc-  
tion and failure.  
With the vehicle stopped and engine off,  
check for excessive free-play in the  
steering wheel.  
Brake discs, pads, calipers and  
rotors  
Use only specified automatic  
transaxle  
Check the linkage for bends or damage.  
Check the dust boots and ball joints for  
deterioration, cracks, or damage.  
Replace any damaged parts.  
fluid.  
(Refer  
to  
Check the pads for excessive wear, discs  
for run out and wear, and calipers for fluid  
leakage.  
“Recommended lubricants and  
capacities” in section 8.)  
Brake hoses and lines  
Drive shafts and boots  
Exhaust pipe and muffler  
Visually check for proper installation,  
chafing, cracks, deterioration and any  
leakage. Replace any deteriorated or  
damaged parts immediately.  
Check the drive shafts, boots and clamps  
for cracks, deterioration, or damage.  
Replace any damaged parts and, if nec-  
essary, repack the grease.  
Visually inspect the exhaust pipes, muf-  
fler and hangers for cracks, deterioration,  
or damage. Start the engine and listen  
carefully for any exhaust gas leakage.  
Tighten connections or replace parts as  
necessary.  
Brake/Clutch* fluid  
Air conditioning refrigerant  
Check the brake fluid level in the brake  
fluid reservoir. The level should be  
between “MIN” and “MAX” marks on the  
side of the reservoir. Use only hydraulic  
brake fluid conforming to DOT 3 or DOT  
4 specification.  
Check the air conditioning lines and con-  
nections for leakage and damage.  
Suspension mounting bolts  
Check the suspension connections for  
looseness or damage. Retighten to the  
specified torque.  
* : if equipped  
7 20  
Maintenance  
ENGINE OIL  
3. Turn the engine off and wait for a few  
minutes (about 5 minutes) for the oil to  
return to the oil pan.  
4. Pull the dipstick out, wipe it clean, and  
re-insert it fully.  
WARNING - Radiator hose  
Be very careful not to touch the  
radiator hose when checking or  
adding the engine oil as it may be  
hot enough to burn you.  
OLM079003N  
OLM079004N  
5. Pull the dipstick out again and check  
the level. The level should be between  
F and L.  
If it is near or at L, add enough oil to bring  
the level to F. Do not overfill.  
Checking the engine oil level  
1. Be sure the vehicle is on level ground.  
2. Start the engine and allow it to reach  
normal operating temperature.  
Use a funnel to help prevent oil from  
being spilled on engine components.  
CAUTION  
Do not overfill with engine oil.  
Engine damage may result.  
Use only the specified engine oil. (Refer  
to “Recommended lubricants and capaci-  
ties” in section 8.)  
7 21  
Maintenance  
ENGINE COOLANT  
The high-pressure cooling system has a  
reservoir filled with year-round antifreeze  
coolant. The reservoir is filled at the fac-  
tory.  
CALIFORNIA PROPOSI-  
TION 65 WARNING  
Engine oil contains chemicals  
known to the State of California to  
cause cancer, birth defects, and  
reproductive harm.  
Check the antifreeze protection and  
coolant level at least once a year, at the  
beginning of the winter season, and  
before traveling to a colder climate.  
Used engine oil may cause irrita-  
tion or cancer of the skin if left in  
contact with the skin for prolonged  
periods of time. Used engine oil  
contains chemicals that have  
caused cancer in laboratory ani-  
mals. Always protect your skin by  
washing your hands thoroughly  
with soap and warm water as soon  
as possible after handling used oil.  
Checking the coolant level  
WARNING - Removing  
radiator cap  
Changing the engine oil and filter  
• Never attempt to remove the radi-  
ator cap while the engine is oper-  
ating or hot. Doing so might lead  
to cooling system and engine  
damage. Also, hot coolant or  
steam could cause serious per-  
sonal injury.  
Have engine oil and filter changed by an  
authorized HYUNDAI dealer according to  
the Maintenance Schedule at the begin-  
ning of this section.  
(Continued)  
7 22  
Maintenance  
Recommended engine coolant  
(Continued)  
• When adding coolant, use only deion-  
ized water or soft water for your vehicle  
and never mix hard water in the  
coolant filled at the factory. An improp-  
er coolant mixture can result in serious  
malfunction or engine damage.  
• Turn the engine off and wait until  
it cools down. Use extreme care  
when removing the radiator cap.  
Wrap a thick towel around it, and  
turn it counterclockwise slowly to  
the first stop. Step back while the  
pressure is released from the  
cooling system. When you are  
sure all the pressure has been  
released, press down on the cap,  
using a thick towel, and continue  
turning counterclockwise to  
remove it.  
• The engine in your vehicle has alu-  
minum engine parts and must be pro-  
tected by an ethylene-glycol-based  
coolant to prevent corrosion and freez-  
ing.  
OLM079006  
• DO NOT USE alcohol or methanol  
coolant or mix them with the specified  
coolant.  
Check the condition and connections of  
all cooling system hoses and heater  
hoses. Replace any swollen or deterio-  
rated hoses.  
• Even if the engine is not operat-  
ing, do not remove the radiator  
cap or the drain plug while the  
engine and radiator are hot. Hot  
coolant and steam may still blow  
out under pressure, causing seri-  
ous injury.  
• Do not use a solution that contains  
more than 60% antifreeze or less than  
35% antifreeze, which would reduce  
the effectiveness of the solution.  
The coolant level should be filled  
between F and L marks on the side of the  
coolant reservoir when the engine is  
cool.  
If the coolant level is low, add enough  
specified coolant to provide protection  
against freezing and corrosion. Bring the  
level to F, but do not overfill. If frequent  
additions are required, see an authorized  
HYUNDAI dealer for a cooling system  
inspection.  
7 23  
Maintenance  
For mixture percentage, refer to the fol-  
lowing table.  
Changing the coolant  
Have coolant changed by an authorized  
HYUNDAI dealer according to the  
Maintenance Schedule at the beginning  
of this section.  
Mixture Percentage (volume)  
Ambient  
Temperature  
Water  
Antifreeze  
CAUTION  
Put a thick cloth around the radiator  
cap before refilling the coolant in  
order to prevent the coolant from  
overflowing into engine parts such  
as the generator.  
5°F (-15°C)  
-13°F (-25°C)  
-31°F (-35°C)  
-49°F (-45°C)  
35  
40  
50  
60  
65  
60  
50  
40  
OLM079007  
WARNING - Radiator cap  
WARNING - Coolant  
Do not remove the radiator cap  
when the engine and radiator are  
hot. Scalding hot coolant and  
steam may blow out under pres-  
sure causing serious injury.  
• Do not use radiator coolant or  
antifreeze in the washer fluid  
reservoir.  
• Radiator coolant can severely  
obscure visibility when sprayed  
on the windshield and may cause  
loss of vehicle control or damage  
to paint and body trim.  
7 24  
Maintenance  
BRAKE/CLUTCH (IF EQUIPPED) FLUID  
If the level is low, add fluid to the MAX  
level. The level will fall with accumulated  
mileage. This is a normal condition asso-  
ciated with the wear of the brake linings  
and/or clutch disc (if equipped). If the  
fluid level is excessively low, have the  
brake/clutch* system checked by an  
authorized HYUNDAI dealer.  
WARNING - Brake/clutch*  
fluid  
When changing and adding  
brake/clutch* fluid, handle it care-  
fully. Do not let it come in contact  
with your eyes. If brake/clutch* fluid  
should come in contact with your  
eyes, immediately flush them with a  
large quantity of fresh tap water.  
Have your eyes examined by a doc-  
tor as soon as possible.  
Use only the specified brake/clutch* fluid.  
(Refer to “Recommended lubricants and  
capacities” in section 8.)  
OLM079008N  
Never mix different types of fluid.  
Checking the brake/clutch* fluid  
level  
CAUTION  
Check the fluid level in the reservoir peri-  
odically. The fluid level should be  
between MAX and MIN marks on the  
side of the reservoir.  
Do not allow brake/clutch* fluid to  
contact the vehicle's body paint, as  
paint damage will result.  
WARNING - Loss of  
brake/clutch* fluid  
In the event the brake/clutch* system  
requires frequent additions of fluid,  
the vehicle should be inspected by  
an authorized HYUNDAI dealer.  
Brake/clutch* fluid, which has been  
exposed to open air for an extended  
time should never be used as its  
quality cannot be guaranteed. It  
should be disposed of properly.  
Don't put in the wrong kind of fluid.  
A few drops of mineral-based oil,  
such as engine oil, in your  
brake/clutch* system can damage  
brake/clutch* system parts.  
Before removing the reservoir cap and  
adding brake/clutch* fluid, clean the area  
around the reservoir cap thoroughly to  
prevent brake/clutch* fluid contamina-  
tion.  
*
:
if equipped  
7 25  
Maintenance  
WASHER FLUID  
WARNING - Coolant  
• Do not use radiator coolant or  
antifreeze in the washer fluid  
reservoir.  
• Radiator coolant can severely  
obscure visibility when sprayed  
on the windshield and may cause  
loss of vehicle control or damage  
to paint and body trim.  
• Windshield washer fluid agents  
contain some amounts of alcohol  
and can be flammable under cer-  
tain circumstances. Do not allow  
sparks or flame to contact the  
washer fluid or the washer fluid  
reservoir. Damage to the vehicle  
or occupants could occur.  
OLM079010  
Checking the washer fluid level  
Check the fluid level in the washer fluid  
reservoir and add fluid if necessary. Plain  
water may be used if washer fluid is not  
available. However, use washer solvent  
with antifreeze characteristics in cold cli-  
mates to prevent freezing.  
• Windshield washer fluid is poi-  
sonous to humans and animals.  
Do not drink and avoid contacting  
windshield washer fluid. Serious  
injury or death could occur.  
7 26  
Maintenance  
PARKING BRAKE  
OLM059014  
OLM059016  
Checking the parking brake  
Type A  
Type B  
Check the stroke of the parking brake by  
counting the number of “clicks’’ heard  
while fully applying it from the released  
position. Also, the parking brake alone  
should securely hold the vehicle on a fair-  
ly steep grade. If the stroke is more or  
less than specified, have the parking  
brake adjusted by an authorized  
HYUNDAI dealer.  
Check whether the stroke is within spec-  
ification when the parking brake pedal is  
depressed with 44 lb (20 kg, 196 N) of  
force. Also, the parking brake alone  
should securely hold the vehicle on a fair-  
ly steep grade. If the stroke is more or  
less than specified, have the parking  
brake adjusted by an authorized  
HYUNDAI dealer.  
Stroke : 6 “clicks’’ at  
a
44 lbs (20 kg, 196 N).  
force of  
Stroke : 4 notch  
7 27  
Maintenance  
AIR CLEANER  
OLM079012N  
OLM079013N  
OLM079014  
1. Loosen the air cleaner cover attaching  
clips and open the cover.  
2. Wipe the inside of the air cleaner.  
3. Replace the air cleaner filter.  
Filter replacement  
It must be replaced when necessary, and  
should not be washed.  
4. Lock the cover with the cover attaching  
clips.  
You can clean the filter when inspecting  
the air cleaner element.  
Clean the filter by using compressed air.  
Replace the filter according to the  
Maintenance Schedule.  
If the vehicle is operated in extremely  
dusty or sandy areas, replace the ele-  
ment more often than the usual recom-  
mended intervals. (Refer to “Maintenance  
under severe usage conditions” in this  
section.)  
7 28  
Maintenance  
CLIMATE CONTROL AIR FILTER  
Filter inspection  
CAUTION  
The climate control air filter should be  
replaced according to the Maintenance  
Schedule. If the vehicle is operated in  
severely air-polluted cities or on dusty  
rough roads for a long period, it should  
be inspected more frequently and  
replaced earlier. When you replace the  
climate control air filter, replace it per-  
forming the following procedure, and be  
careful to avoid damaging other compo-  
nents.  
• Do not drive with the air cleaner  
removed; this will result in exces-  
sive engine wear.  
• When removing the air cleaner fil-  
ter, be careful that dust or dirt  
does not enter the air intake, or  
damage may result.  
• Use a HYUNDAI genuine part. Use  
of non-genuine parts could dam-  
age the air flow sensor.  
OLM079015  
Filter replacement  
1. Open the glove box and remove the  
support rod (1).  
7 29  
Maintenance  
OLM079016  
OLM079017  
OLM079018  
2. With the glove box open, remove the  
stoppers on both sides.  
3. Remove the climate control air filter  
case pulling out both sides of the  
cover.  
4. Replace the climate control air filter.  
5. Reassemble in the reverse order of  
disassembly.  
✽
NOTICE  
When replacing the climate control air  
filter install it properly. Otherwise, the  
system may produce noise and the effec-  
tiveness of the filter may be reduced.  
7 30  
Maintenance  
WIPER BLADES  
Contamination of either the windshield or  
the wiper blades with foreign matter can  
reduce the effectiveness of the wind-  
shield wipers. Common sources of con-  
tamination are insects, tree sap, and hot  
wax treatments used by some commer-  
cial car washes. If the blades are not wip-  
ing properly, clean both the window and  
the blades with a good cleaner or mild  
detergent, and rinse thoroughly with  
clean water.  
Blade replacement  
When the wipers no longer clean ade-  
quately, the blades may be worn or  
cracked, and require replacement.  
CAUTION  
To prevent damage to the wiper  
arms or other components, do not  
attempt to move the wipers manual-  
ly.  
1JBA5122  
CAUTION  
Blade inspection  
CAUTION  
To prevent damage to the wiper  
blades, do not use gasoline,  
kerosene, paint thinner, or other  
solvents on or near them.  
The use of a non-specified wiper  
blade could result in wiper malfunc-  
tion and failure.  
✽
NOTICE  
Commercial hot waxes applied by auto-  
matic car washes have been known to  
make the windshield difficult to clean.  
7 31  
Maintenance  
OLM079200  
OLM079201  
OLM079202  
2. Compress the clip and slide the blade  
assembly downward.  
Front windshield wiper blade  
3. Lift it off the arm.  
4. Install the blade assembly in the  
reverse order of removal.  
1. Raise the wiper arm and turn the wiper  
blade assembly to expose the plastic  
locking clip.  
CAUTION  
Do not allow the wiper arm to fall  
against the windshield, since it may  
chip or crack the windshield.  
7 32  
Maintenance  
OHM078062  
OHM078063  
Rear window wiper blade  
1. Raise the wiper arm and pull out the  
wiper blade assembly.  
2. Install the new blade assembly by  
inserting the center part into the slot in  
the wiper arm until it clicks into place.  
3. Make sure the blade assembly is  
installed firmly by trying to pull it slight-  
ly.  
To prevent damage to the wiper arms or  
other components, have an authorized  
HYUNDAI dealer replace the wiper  
blade.  
7 33  
Maintenance  
BATTERY  
(Continued)  
If any electrolyte gets into  
WARNING - Battery  
dangers  
your eyes, flush your eyes  
with clean water for at least  
15 minutes and get immedi-  
ate medical attention.  
Always read the following  
instructions carefully when  
handling a battery.  
Keep lighted cigarettes and  
all other flames or sparks  
away from the battery.  
If electrolyte gets on your  
skin, thoroughly wash the  
contacted area. If you feel a  
pain or a burning sensa-  
tion, get medical attention  
immediately.  
Hydrogen, a highly com-  
bustible gas, is always  
present in battery cells and  
may explode if ignited.  
OLM079019N  
For best battery service  
Wear eye protection when  
charging or working near a  
battery. Always provide  
ventilation when working in  
an enclosed space.  
• Keep the battery securely mounted.  
• Keep the battery top clean and dry.  
Keep batteries out of the  
reach of children because  
batteries contain highly  
corrosive SULFURIC ACID.  
Do not allow battery acid to  
contact your skin, eyes,  
clothing or paint finish.  
• Keep the terminals and connections  
clean, tight, and coated with petroleum  
jelly or terminal grease.  
An inappropriately dis-  
posed battery can be harm-  
ful to the environment and  
human health. Dispose the  
battery according to your  
local law(s) or regulation.  
• Rinse any spilled electrolyte from the  
battery immediately with a solution of  
water and baking soda.  
(Continued)  
• If the vehicle is not going to be used for  
an extended time, disconnect the bat-  
tery cables.  
(Continued)  
7 34  
Maintenance  
Battery recharging  
(Continued)  
CALIFORNIA PROPOSI-  
TION 65 WARNING  
Your vehicle has a maintenance-free,  
calcium-based battery.  
• When lifting a plastic-cased bat-  
tery, excessive pressure on the  
case may cause battery acid to  
leak, resulting in personal injury.  
Lift with a battery carrier or with  
your hands on opposite corners.  
Battery posts, terminals, and relat-  
ed accessories contain lead and  
lead compounds, chemicals known  
to the State of California to cause  
cancer, birth defects, and reproduc-  
tive harm. Batteries also contain  
other chemicals known to the State  
of California to cause cancer. Wash  
hands after handling.  
• If the battery becomes discharged in a  
short time (because, for example, the  
headlights or interior lights were left on  
while the vehicle was not in use),  
recharge it by slow charging (trickle)  
for 10 hours.  
• Never attempt to recharge the  
battery when the battery cables  
are connected.  
• If the battery gradually discharges  
because of high electric load while the  
vehicle is being used, recharge it at 20-  
30A for two hours.  
• The electrical ignition system  
works with high voltage. Never  
touch these components with the  
engine running or the ignition  
switched on.  
WARNING - Recharging  
battery  
When recharging the battery,  
observe the following precautions:  
Failure to follow the above warn-  
ings can result in serious bodily  
injury or death.  
• The battery must be removed  
from the vehicle and placed in an  
area with good ventilation.  
• Do not allow cigarettes, sparks,  
or flame near the battery.  
• Watch the battery during charg-  
ing, and stop or reduce the charg-  
ing rate if the battery cells begin  
gassing (boiling) violently or if  
the temperature of the electrolyte  
of any cell exceeds 120°F (49°C).  
(Continued)  
7 35  
Maintenance  
Reset items  
(Continued)  
Items should be reset after the battery  
has been discharged or the battery has  
been disconnected.  
• Wear eye protection when check-  
ing the battery during charging.  
• Disconnect the battery charger in  
the following order.  
• Auto up/down window (See section 4)  
• Sunroof (See section 4)  
• Trip computer (See section 4)  
1. Turn off the battery charger main  
switch.  
• Climate control system  
(See section 4)  
2. Unhook the negative clamp from  
the negative battery terminal.  
• Clock (See section 4)  
• Audio (See section 4)  
3. Unhook the positive clamp from  
the positive battery terminal.  
WARNING  
• Before performing maintenance  
or recharging the battery, turn off  
all accessories and stop the  
engine.  
• The negative battery cable must  
be removed first and installed  
last when the battery is discon-  
nected.  
7 36  
Maintenance  
TIRES AND WHEELS  
Tire care  
CAUTION  
For proper maintenance, safety, and  
maximum fuel economy, you must  
always maintain recommended tire  
inflation pressures and stay within  
the load limits and weight distribution  
recommended for your vehicle.  
• Underinflation also results in  
excessive wear, poor handling  
and reduced fuel economy.  
Wheel deformation also is  
possible. Keep your tire pres-  
sures at the proper levels. If a  
tire frequently needs refilling,  
have it checked by an author-  
ized HYUNDAI dealer.  
Recommended cold tire inflation  
pressures  
All tire pressures (including the  
spare) should be checked when the  
tires are cold. “Cold Tires” means the  
vehicle has not been driven for at  
least three hours or driven less than  
one mile (1.6 km).  
• Overinflation produces  
a
OLM089008N  
harsh ride, excessive wear at  
the center of the tire tread, and  
a greater possibility of dam-  
age from road hazards.  
All specifications (sizes and pres-  
sures) can be found on a label  
attached to the driver’s side center  
pillar.  
Recommended pressures must be  
maintained for the best ride, vehicle  
handling, and minimum tire wear.  
WARNING - Tire underin-  
flation  
Severe underinflation can lead  
to severe heat build-up, causing  
blowouts, tread separation and  
other tire failures that can result  
in the loss of vehicle control  
leading to severe injury or  
death. This risk is much higher  
on hot days and when driving  
for long periods at high speeds.  
For recommended inflation pressure,  
refer to “Tire and wheels” in section  
8.  
7 37  
Maintenance  
Checking tire inflation pressure  
CAUTION  
CAUTION - Tire pressure  
Always observe the following:  
Check your tires once a month or  
more.  
• Warm tires normally exceed  
recommended cold tire pres-  
sures by 4 to 6 psi (28 to 41  
kPa). Do not release air from  
warm tires to adjust the pres-  
sure or the tires will be under-  
inflated.  
• Check tire pressure when the  
tires are cold. (After vehicle  
has been parked for at least  
three hours or hasn't been  
driven more than one mile (1.6  
km) since startup.)  
Also, check the tire pressure of the  
spare tire.  
How to check  
Use a good quality gage to check tire  
pressure.You can not tell if your tires  
are properly inflated simply by look-  
ing at them. Radial tires may look  
properly inflated even when they're  
underinflated.  
• Be sure to reinstall the tire  
inflation valve caps. Without  
the valve cap, dirt or moisture  
could get into the valve core  
and cause air leakage. If a  
valve cap is missing, install a  
new one as soon as possible.  
• Check the pressure of your  
spare tire each time you check  
the pressure of other tires.  
• Never overload your vehicle.  
Be careful not to overload a  
vehicle luggage rack if your  
vehicle is equipped with one.  
Check the tire's inflation pressure  
when the tires are cold. - "Cold"  
means your vehicle has been sitting  
for at least three hours or driven no  
more than 1 mile (1.6 km).  
• Worn, old tires can cause acci-  
dents. If your tread is badly  
worn, or if your tires have  
been damaged, replace them.  
WARNING - Tire Inflation  
Overinflation or underinflation  
can reduce tire life, adversely  
affect vehicle handling, and  
lead to sudden tire failure. This  
could result in loss of vehicle  
control and potential injury.  
7 38  
Maintenance  
Remove the valve cap from the tire  
valve stem. Press the tire gage firm-  
ly onto the valve to get a pressure  
measurement. If the cold tire inflation  
pressure matches the recommended  
pressure on the tire and loading  
information label, no further adjust-  
ment is necessary. If the pressure is  
low, add air until you reach the rec-  
ommended amount.  
Tire rotation  
WARNING  
To equalize tread wear, it is recom-  
mended that the tires be rotated  
every 7,500 miles (12,000 km) or  
sooner if irregular wear develops.  
• Inspect your tires frequently  
for proper inflation as well as  
wear and damage. Always use  
a tire pressure gauge.  
During rotation, check the tires for  
correct balance.  
• Tires with too much or too little  
pressure wear unevenly caus-  
ing poor handling, loss of vehi-  
cle control, and sudden tire  
failure leading to accidents,  
injuries, and even death. The  
recommended cold tire pres-  
sure for your vehicle can be  
found in this manual and on  
the tire label located on the dri-  
ver's side center pillar.  
When rotating tires, check for uneven  
wear and damage. Abnormal wear is  
usually caused by incorrect tire pres-  
sure, improper wheel alignment, out-  
of-balance wheels, severe braking or  
severe cornering. Look for bumps or  
bulges in the tread or side of tire.  
Replace the tire if you find either of  
these conditions. Replace the tire if  
fabric or cord is visible. After rotation,  
be sure to bring the front and rear tire  
pressures to specification and check  
lug nut tightness.  
If you overfill the tire, release air by  
pushing on the metal stem in the  
center of the tire valve. Recheck the  
tire pressure with the tire gage. Be  
sure to put the valve caps back on  
the valve stems. They help prevent  
leaks by keeping out dirt and mois-  
ture.  
• Worn tires can cause acci-  
dents. Replace tires that are  
worn, show uneven wear, or  
are damaged.  
Refer to “Tire and wheels” in section  
8.  
• Remember to check the pres-  
sure of your spare tire.  
HYUNDAI recommends that  
you check the spare every  
time you check the pressure  
of the other tires on your vehi-  
cle.  
7 39  
Maintenance  
Without a spare tire  
Disc brake pads should be inspected Wheel alignment and tire balance  
for wear whenever tires are rotated.  
The wheels on your vehicle were  
aligned and balanced carefully at the  
factory to give you the longest tire life  
and best overall performance.  
✽
NOTICE  
Rotate radial tires that have an  
In most cases, you will not need to  
have your wheels aligned again.  
However, if you notice unusual tire  
wear or your vehicle pulling one way  
or the other, the alignment may need  
to be reset.  
asymmetric tread pattern only from  
front to rear and not from right to  
left.  
S2BLA790A  
WARNING  
• Do not use the compact spare  
tire for tire rotation.  
Directional tires (if equipped)  
If you notice your vehicle vibrating  
when driving on a smooth road, your  
wheels may need to be rebalanced.  
• Do not mix bias ply and radial  
ply tires under any circum-  
stances. This may cause  
unusual handling characteris-  
tics that could result in death,  
severe injury, or property  
damage.  
CAUTION  
Improper wheel weights can  
damage your vehicle's alu-  
minum wheels. Use only  
approved wheel weights.  
CBGQ0707A  
7 40  
Maintenance  
(Continued)  
Tread wear indicator  
WARNING - Replacing  
tires  
To reduce the chance or serious  
or fatal injuries from an acci-  
dent caused by tire failure or  
loss of vehicle control:  
• Using tires and wheel other  
than the recommended sizes  
could cause unusual handling  
characteristics and poor vehi-  
cle control, resulting in a seri-  
ous accident.  
• Replace tires that are worn,  
show uneven wear, or are  
damaged. Worn tires can  
cause loss of braking effec-  
tiveness, steering control, and  
traction.  
• Wheels that do not meet  
HYUNDAI’s specifications may  
fit poorly and result in damage  
to the vehicle or unusual han-  
dling and poor vehicle control.  
OEN076053  
Tire replacement  
• The ABS works by comparing  
the speed of the wheels. Tire  
size can affect wheel speed.  
When replacing tires, all 4  
tires must use the same size  
originally supplied with the  
vehicle. Using tires of a differ-  
ent size can cause the ABS  
(Anti-lock Brake System) and  
ESC (Electronic Stability  
Control) to work irregularly (if  
equipped).  
• Do not drive your vehicle with  
too little or too much pressure  
in your tires. This can lead to  
uneven wear and tire failure.  
If the tire is worn evenly, a tread wear  
indicator will appear as a solid band  
across the tread. This shows there is  
less than 1/16 inch (1.6 mm) of tread  
left on the tire. Replace the tire when  
this happens.  
• When replacing tires, never  
mix radial and bias-ply tires  
on the same car. You must  
replace all tires (including the  
spare) if moving from radial to  
bias-ply tires.  
Do not wait for the band to appear  
across the entire tread before replac-  
ing the tire.  
(Continued)  
7 41  
Maintenance  
Compact spare tire replacement  
Wheel replacement  
Tire traction  
A compact spare tire has a shorter  
tread life than a regular size tire.  
Replace it when you can see the  
tread wear indicator bars on the tire.  
The replacement compact spare tire  
should be the same size and design  
tire as the one provided with your  
new vehicle and should be mounted  
on the same compact spare tire  
wheel. The compact spare tire is not  
designed to be mounted on a regular  
size wheel, and the compact spare  
tire wheel is not designed for mount-  
ing a regular size tire.  
When replacing the metal wheels for Tire traction can be reduced if you  
any reason, make sure the new drive on worn tires, tires that are  
wheels are equivalent to the original improperly inflated or on slippery  
factory units in diameter, rim width road surfaces. Tires should be  
and offset.  
replaced when tread wear indicators  
appear. Slow down whenever there  
is rain, snow or ice on the road to  
reduce the possibility of losing con-  
trol of the vehicle.  
WARNING  
A wheel that is not the correct  
size may adversely affect wheel  
and bearing life, braking and  
stopping abilities, handling  
characteristics, ground clear-  
ance, body-to-tire clearance,  
Tire maintenance  
In addition to proper inflation, correct  
wheel alignment helps to decrease  
tire wear. If you find a tire is worn  
unevenly, have your dealer check the  
wheel alignment.  
snow  
chain  
clearance,  
speedometer and odometer cal-  
ibration, headlight aim and  
bumper height.  
When you have new tires installed,  
make sure they are balanced. This  
will increase vehicle ride comfort and  
tire life. Additionally, a tire should  
always be rebalanced if it is removed  
from the wheel.  
7 42  
Maintenance  
Wheel size designation  
2. Tire size designation  
1
Wheels are also marked with impor-  
tant information that you need if you  
ever have to replace one. The follow-  
ing explains what the letters and  
numbers in the wheel size designa-  
tion mean.  
A tire’s sidewall is marked with a tire  
size designation. You will need this  
information when selecting replace-  
ment tires for your car. The following  
explains what the letters and num-  
bers in the tire size designation  
mean.  
5,6  
7
4
2
3
Example tire size designation:  
Example wheel size designation:  
(These numbers are provided as an  
example only; your tire size designa-  
tor could vary depending on your  
vehicle.)  
6.5JX18  
1
I030B04JM  
6.5 - Rim width in inches.  
J - Rim contour designation.  
18 - Rim diameter in inches.  
Tire sidewall labeling  
225/55R18 105T  
This information identifies and  
describes the fundamental charac-  
teristics of the tire and also provides  
the tire identification number (TIN)  
for safety standard certification. The  
TIN can be used to identify the tire in  
case of a recall.  
225 - Tire width in millimeters.  
55 - Aspect ratio. The tire’s section  
height as a percentage of its  
width.  
R - Tire construction code (Radial).  
18 - Rim diameter in inches.  
1. Manufacturer or brand name  
Manufacturer or Brand name is  
shown.  
105 - Load Index, a numerical code  
associated with the maximum  
load the tire can carry.  
T - Speed Rating Symbol. See the  
speed rating chart in this section  
for additional information.  
7 43  
Maintenance  
Tire speed ratings  
3. Checking tire life (TIN :Tire  
Identification Number)  
WARNING - Tire age  
Tires degrade over time, even  
when they are not being used.  
The chart below lists many of the dif-  
ferent speed ratings currently being  
used for passenger car tires. The  
speed rating is part of the tire size  
designation on the sidewall of the  
tire. This symbol corresponds to that  
tire's designed maximum safe oper-  
ating speed.  
Any tires that are over 6 years old,  
based on the manufacturing date,  
(including the spare tire) should be  
replaced by new ones. You can find  
the manufacturing date on the tire  
sidewall (possibly on the inside of the  
wheel), displaying the DOT Code.  
The DOT Code is a series of num-  
bers on a tire consisting of numbers  
and English letters. The manufactur-  
ing date is designated by the last four  
digits (characters) of the DOT code.  
Regardless of the remaining  
tread, it is recommended that  
tires generally be replaced after  
six (6) years of normal service.  
Heat caused by hot climates or  
frequent high loading condi-  
tions can accelerate the aging  
process. Failure to follow this  
warning can result in sudden  
tire failure, which could lead to  
a loss of control and an acci-  
dent involving serious injury or  
death.  
Speed  
Rating  
Symbol  
Maximum Speed  
S
T
H
V
Z
112 mph (180 km/h)  
118 mph (190 km/h)  
DOT : XXXX XXXX OOOO  
130 mph (210 km/h)  
The front part of the DOT means a  
plant code number, tire size and  
tread pattern and the last four num-  
bers indicate week and year manu-  
factured.  
149 mph (240 km/h)  
Above 149 mph (240 km/h)  
4. Tire ply composition and material  
The number of layers or plies of rub-  
ber-coated fabric in the tire. Tire  
manufacturers also must indicate the  
materials in the tire, which include  
steel, nylon, polyester, and others.  
The letter "R" means radial ply con-  
struction; the letter "D" means diago-  
nal or bias ply construction; and the  
letter "B" means belted-bias ply con-  
struction.  
For example:  
DOT XXXX XXXX 1610 represents  
that the tire was produced in the 16th  
week of 2010.  
7 44  
Maintenance  
5. Maximum permissible inflation  
pressure  
7. Uniform tire quality grading  
Quality grades can be found where  
applicable on the tire sidewall  
between tread shoulder and maxi-  
mum section width.  
The tires available as standard or  
optional equipment on your vehicle  
may vary with respect to grade.  
This number is the greatest amount  
of air pressure that should be put in  
the tire. Do not exceed the maximum  
permissible inflation pressure. Refer  
to the Tire and Loading Information  
label for recommended inflation  
pressure.  
Traction - AA, A, B & C  
For example:  
The traction grades, from highest to  
lowest, are AA, A, B and C. Those  
grades represent the tire’s ability to  
stop on wet pavement as measured  
under controlled conditions on spec-  
ified government test surfaces of  
asphalt and concrete. A tire marked  
C may have poor traction perform-  
ance.  
TREAD wear 200  
TRACTION AA  
TEMPERATURE A  
6. Maximum load rating  
Tread wear  
This number indicates the maximum  
load in kilograms and pounds that  
can be carried by the tire. When  
replacing the tires on the vehicle,  
always use a tire that has the same  
load rating as the factory installed  
tire.  
The tread wear grade is a compara-  
tive rating based on the wear rate of  
the tire when tested under controlled  
conditions on a specified govern-  
ment test course. For example, a tire  
graded 150 would wear one-and-a-  
half times (1½) as well on the gov-  
ernment course as a tire graded 100.  
WARNING  
The traction grade assigned to  
this tire is based on straight-  
ahead braking traction tests,  
and does not include accelera-  
tion, cornering, hydroplaning,  
or peak traction characteristics.  
The relative performance of tires  
depends upon the actual conditions  
of their use, however, and may  
depart significantly from the norm  
due to variations in driving habits,  
service practices and differences in  
road characteristics and climate.  
These grades are molded on the  
side-walls of passenger vehicle tires.  
7 45  
Maintenance  
Temperature -A, B & C  
Tire terminology and definitions  
Air Pressure: The amount of air  
inside the tire pressing outward on  
the tire. Air pressure is expressed in  
pounds per square inch (psi) or kilo-  
pascal (kPa).  
WARNING - Tire  
temperature  
The temperature grades are A (the  
highest), B and C representing the  
tire’s resistance to the generation of  
heat and its ability to dissipate heat  
when tested under controlled condi-  
tions on a specified indoor laboratory  
test wheel.  
The temperature grade for this  
tire is established for a tire that  
is properly inflated and not  
overloaded. Excessive speed,  
underinflation, or excessive  
loading, either separately or in  
combination, can cause heat  
build-up and possible sudden  
tire failure. This can cause loss  
of vehicle control and serious  
injury or death.  
Accessory Weight: This means the  
combined weight of optional acces-  
sories. Some examples of optional  
accessories are, automatic transaxle,  
power seats, and air conditioning.  
Sustained high temperature can  
cause the material of the tire to  
degenerate and reduce tire life, and  
excessive temperature can lead to  
sudden tire failure. The grade C cor-  
responds to a level of performance  
which all passenger car tires must  
meet under the Federal Motor  
Vehicle Safety Standard No. 109.  
Grades B and A represent higher  
levels of performance on the labora-  
tory test wheel than the minimum  
required by law.  
Aspect Ratio: The relationship of a  
tire's height to its width.  
Belt: A rubber coated layer of cords  
that is located between the plies and  
the tread. Cords may be made from  
steel or other reinforcing materials.  
Bead: The tire bead contains steel  
wires wrapped by steel cords that  
hold the tire onto the rim.  
Bias Ply Tire: A pneumatic tire in  
which the plies are laid at alternate  
angles less than 90 degrees to the  
centerline of the tread.  
7 46  
Maintenance  
Cold Tire Pressure: The amount of Intended Outboard Sidewall: The Occupant Distribution: Designated  
air pressure in a tire, measured in side of an asymmetrical tire, that seating positions.  
pounds per square inch (psi) or kilo- must always face outward when  
pascals (kPa) before a tire has built mounted on a vehicle.  
up heat from driving.  
Outward Facing Sidewall: The side  
of a asymmetrical tire that has a par-  
Kilopascal (kPa): The metric unit for ticular side that faces outward when  
Curb Weight: This means the weight air pressure.  
of a motor vehicle with standard and  
mounted on a vehicle. The outward  
facing sidewall bears white lettering  
or bears manufacturer, brand, and/or  
model name molding that is higher or  
deeper than the same moldings on  
the inner facing sidewall.  
Load Index: An assigned number  
optional equipment including the  
maximum capacity of fuel, oil and  
coolant, but without passengers and  
cargo.  
ranging from 1 to 279 that corre-  
sponds to the load carrying capacity  
of a tire.  
Maximum Inflation Pressure: The  
maximum air pressure to which a  
cold tire may be inflated. The maxi-  
mum air pressure is molded onto the  
sidewall.  
DOT Markings: A code molded into  
the sidewall of a tire signifying that  
the tire is in compliance with the U.S.  
Department of Transportation motor  
vehicle safety standards. The DOT  
code includes the Tire Identification  
Number (TIN), an alphanumeric des-  
ignator which can also identify the  
tire manufacturer, production plant,  
brand and date of production.  
Passenger (P-Metric) Tire: A tire  
used on passenger cars and some  
light duty trucks and multipurpose  
vehicles.  
Recommended Inflation Pressure:  
Vehicle manufacturer's recommend-  
ed tire inflation pressure and shown  
on the tire placard.  
Maximum Load Rating: The load  
rating for a tire at the maximum per-  
missible inflation pressure for that  
tire.  
Radial Ply Tire: A pneumatic tire in  
which the ply cords that extend to the  
beads are laid at 90 degrees to the  
centerline of the tread.  
Maximum Loaded Vehicle Weight:  
The sum of curb weight; accessory  
weight; vehicle capacity weight; and  
production options weight.  
GVWR: Gross Vehicle Weight Rating  
GAWR FRT: Gross Axle Weight  
Rating for the Front Axle.  
Rim: A metal support for a tire and  
upon which the tire beads are seat-  
ed.  
Normal Occupant Weight: The  
number of occupants a vehicle is  
designed to seat multiplied by 150  
pounds (68 kg).  
GAWR RR: Gross Axle Weight  
Rating for the Rear axle.  
Sidewall: The portion of a tire  
between the tread and the bead.  
7 47  
Maintenance  
Speed Rating: An alphanumeric Vehicle Maximum Load on the Summer tires  
code assigned to a tire indicating the Tire: Load on an individual tire due to  
maximum speed at which a tire can curb and accessory weight plus  
HYUNDAI specifies summer tires on  
some models to provide superior  
performance on dry roads. Summer  
tire performance is substantially  
operate.  
maximum occupant and cargo  
weight.  
Traction: The friction between the  
tire and the road surface. The Vehicle Normal Load on the Tire: reduced in snow and ice. Summer  
amount of grip provided.  
Load on an individual tire that is tires do not have the tire traction rat-  
determined by distributing to each ing M+S (Mud and Snow) on the tire  
axle its share of the curb weight, side wall. if you plan to operate your  
accessory weight, and normal occu- vehicle in snowy or icy conditions.  
Tread: The portion of a tire that  
comes into contact with the road.  
Treadwear Indicators: Narrow  
bands, sometimes called "wear  
bars," that show across the tread of a  
tire when only 2/32 inch of tread  
remains.  
pant weight and dividing by 2.  
HYUNDAI recommends the use of  
snow tires or all season tires on all  
four wheels.  
Vehicle Placard: A label permanent-  
ly attached to a vehicle showing the  
original equipment tire size and rec-  
ommended inflation pressure.  
Snow tires  
UTQGS: Uniform Tire Quality  
Grading Standards, a tire information  
system that provides consumers with All season tires  
ratings for a tire's traction, tempera-  
ture and treadwear. Ratings are  
determined by tire manufacturers  
using government testing proce-  
dures. The ratings are molded into  
the sidewall of the tire.  
If you equip your car with snow tires,  
they should be the same size and  
have the same load capacity as the  
original tires. Snow tires should be  
installed on all four wheels; other-  
wise, poor handling may result.  
HYUNDAI specifies all season tires  
on some models to provide good  
performance for use all year round,  
including snowy and icy road condi-  
tions. All season tires are identified  
by ALL SEASON and/or M+S (Mud  
Snow tires should carry 4 psi (28  
kPa) more air pressure than the  
pressure recommended for the stan-  
dard tires on the tire label on the dri-  
ver's side of the center pillar, or up to  
the maximum pressure shown on the  
tire sidewall, whichever is less.  
Vehicle Capacity Weight: The num- and Snow) on the tire sidewall. Snow  
ber of designated seating positions tires have better snow traction than  
multiplied by 150 lbs. (68 kg) plus the all season tires and may be more  
rated cargo and luggage load.  
appropriate in some areas.  
7 48  
Maintenance  
Do not drive faster than 75 mph (120  
km/h) when your vehicle is equipped  
with snow tires.  
Radial-ply tires  
WARNING - Snow or ice  
Radial-ply tires provide improved  
tread life, road hazard resistance and  
smoother high speed ride. The radi-  
al-ply tires used on this vehicle are of  
belted construction, and are selected  
to complement the ride and handling  
characteristics of your vehicle.  
Radial-ply tires have the same load  
carrying capacity, as bias-ply or bias  
belted tires of the same size, and use  
the same recommended inflation  
pressure. Mixing of radial-ply tires  
with bias-ply or bias belted tires is  
not recommended. Any combina-  
tions of radial-ply and bias-ply or bias  
belted tires when used on the same  
vehicle will seriously deteriorate  
vehicle handling. The best rule to fol-  
low is: Identical radial-ply tires should  
always be used as a set of four.  
• When driving on roads cov-  
ered with snow or ice, drive at  
less than 20 mph (30 km/h).  
Tire chains  
• Use the SAE “S” class or wire  
chains.  
Tire chains, if necessary, should be  
installed on the drive wheels as fol-  
lows.  
• If you hear noise caused by  
chains contacting the body,  
retighten the chain to avoid  
contact with the vehicle body.  
2WD : Front wheels  
AWD : All four wheels  
If a full set of chains is not  
available for a AWD vehicle,  
chains may be installed on  
the front wheels only.  
• To prevent body damage,  
retighten the chains after driv-  
ing 0.3~0.6 miles (0.5~1.0 km).  
• Do not use tire chains on  
vehicles equipped with alu-  
minum wheels. In unavoid-  
able circumstance, use a wire  
type chain.  
Be sure that the chains are installed  
in accordance with the manufactur-  
er's instructions.  
To minimize tire and chain wear, do  
not continue to use tire chains when  
they are no longer needed.  
• Use wire chains less than 0.59  
inches (15 mm) to prevent  
damage to the chain’s con-  
nection.  
Longer wearing tires can be more  
susceptible to irregular tread wear. It  
is very important to follow the tire  
rotation interval shown in this section  
to achieve the tread life potential of  
these tires. Cuts and punctures in  
radial-ply tires are repairable only in  
the tread area, because of sidewall  
flexing. Consult your tire dealer for  
radial-ply tire repairs.  
7 49  
Maintenance  
FUSES  
A vehicle’s electrical system is protected  
from electrical overload damage by  
fuses.  
Blade type  
WARNING - Fuse replace-  
ment  
This vehicle has 3 fuse panels, one locat-  
ed in the driver’s side panel bolster, the  
other in the engine compartment.  
• Never replace a fuse with any-  
thing but another fuse of the  
same rating.  
Blown  
Normal  
If any of your vehicle’s lights, acces-  
sories, or controls do not work, check the  
appropriate circuit fuse. If a fuse has  
blown, the element inside the fuse will  
melt.  
• A higher capacity fuse could  
cause damage and possibly a  
fire.  
Cartridge type  
• Never install a wire instead of the  
proper fuse - even as a temporary  
repair. It may cause extensive  
wiring damage and a possible fire.  
If the electrical system does not work,  
first check the driver’s side fuse panel.  
Always replace a blown fuse with one of  
the same rating.  
Normal  
Blown  
Multi fuse  
If the replacement fuse blows, this indi-  
cates an electrical problem. Avoid using  
the system involved and immediately  
consult an authorized HYUNDAI dealer.  
CAUTION  
Do not use a screwdriver or any  
other metal object to remove fuses  
because it may cause a short circuit  
and damage the system.  
Four kinds of fuse are used: blade type,  
cartridge type, multi fuse and main fuse.  
Normal  
Blown  
Main fuse  
Normal  
Blown  
OLM079051N  
7 50  
Maintenance  
If the headlights or other electrical com-  
ponents do not work and the fuses are  
OK, check the fuse panel in the engine  
compartment. If a fuse is blown, it must  
be replaced.  
OLM079021N  
OLM079020  
3. Pull the suspected fuse straight out.  
Use the removal tool provided in the  
fuse panel.  
Instrument panel fuse replace-  
ment  
1. Turn the ignition switch and all other  
switches off.  
2. Open the fuse panel cover.  
4. Check the removed fuse; replace it if it  
is blown.  
Spare fuses are provided in the instru-  
ment panel fuse panel (or in the engine  
compartment fuse panel).  
5. Push in a new fuse of the same rating,  
and make sure it fits tightly in the clips.  
If it fits loosely, consult an authorized  
HYUNDAI dealer.  
If you do not have a spare, use a fuse of  
the same rating from a circuit you may  
not need for operating the vehicle, such  
as the cigarette lighter fuse.  
7 51  
Maintenance  
✽
NOTICE  
• If the memory fuse is pulled up from  
the fuse panel, the warning chime,  
audio, clock and interior lamps, etc.,  
will not operate. Some items must be  
reset after replacement. Refer to  
“Battery” in this section.  
• Even when the memory fuse is pulled  
up, the battery can still be discharged  
by operation of the headlights or other  
electrical devices.  
OLM079022  
OLM079023N  
Memory fuse  
Engine compartment fuse  
replacement  
Your vehicle is equipped with a memory  
fuse to prevent battery discharge if your  
vehicle is parked without being operated  
for prolonged periods. Use the following  
procedures before parking the vehicle for  
prolonged periods.  
1. Turn the ignition switch and all other  
switches off.  
2. Remove the fuse panel cover by  
pressing the tab and pulling the cover  
up.  
1. Turn off the engine.  
2. Turn off the headlights and tail lights.  
3. Check the removed fuse; replace it if it  
is blown. To remove or insert the fuse,  
use the fuse puller in the engine com-  
partment fuse panel.  
3. Open the driver’s side panel cover and  
pull up the memory fuse.  
4. Push in a new fuse of the same rating,  
and make sure it fits tightly in the clips.  
If it fits loosely, consult an authorized  
HYUNDAI dealer.  
7 52  
Maintenance  
✽
NOTICE  
If the main fuse is blown, consult an  
authorized HYUNDAI dealer.  
CAUTION  
After checking the fuse panel in the  
engine compartment, securely  
install the fuse panel cover. If not,  
electrical failures may occur from  
water contact.  
OLM079052N  
Main fuse and Multi fuse  
If the main fuse and Multi fuse is blown,  
it must be removed as follows:  
1. Disconnect the negative battery cable.  
2. Remove the nuts shown in the picture  
above.  
3. Replace the fuse with a new one of the  
same rating.  
4. Reinstall in the reverse order of  
removal.  
7 53  
Maintenance  
Fuse/relay panel description  
Inside the fuse/relay panel covers, you can find the fuse/relay label describing fuse/relay name and capacity.  
Instrument panel fuse panel  
Engine compartment fuse panel  
✽
NOTICE  
Not all fuse panel descriptions in this  
manual may be applicable to your vehi-  
cle. It is accurate at the time of printing.  
When you inspect the fuse panel in your  
vehicle, refer to the fuse panel label.  
OLM079026/OLM079027N/OLM079053N  
7 54  
Maintenance  
Instrument panel fuse panel  
Description  
Fuse rating  
Protected component  
Audio, A/V & Navigation Head Module  
AUDIO 1  
10A  
BCM, Auto Light & Photo Sensor, Room Lamp, Driver/Passenger Vanity Lamp Switch,  
Date Link Connector, Door warning Switch, RF Receiver, A/C Control Module, Luggage Lamp,  
IPS Control Module, Instrument Cluster (IND.), Map Lamp, Electro Chromic Mirror  
ROOM LP  
(MEMORY FUSE)  
10A  
MODULE 2  
START  
10A  
10A  
10A  
10A  
10A  
25A  
10A  
10A  
IPS Control Module, BCM, Electro Chromic Mirror, PDM  
Burglar Alarm Relay, E/R Fuse & Relay Box(Start Relay)  
A/BAG IND  
CLUSTER  
MODULE 4  
POWER OUTLET 2  
AUDIO 2  
Instrument Cluster (Air Bag IND.)  
Audio, Console Switch, Instrument Cluster(IND.), BCM, Alternator, A/V & Navigation Head Module  
E/R Fuse & Relay Box(Blower Relay), Cluster Ionizer, A/C Control Module, Sunroof Motor  
Cigarette Lighter & Front Power Outlet, Rear Power Outlet  
Power Outside Mirror Switch, AMP, BCM, PDM, A/V & Navigation Head Module, Audio  
SRS Control Module, Passenger Occupant Detection Sensor  
A/BAG  
IPS Control Module, Tire Pressure Monitoring Module, EPS Control Module, Steering Angle Sensor,  
ESC OFF Switch, DBC Switch, ICM Relay Box(DBC Relay), Multifunction Switch(Light),  
Stop Lamp Switch, AWD ECM  
MODULE 1  
10A  
FOG LP RR  
10A  
25A  
15A  
15A  
-
WIPER FRT  
Front Wiper Motor, Multifunction Switch(Wiper), E/R Fuse & Relay Box(Front Wiper Relay)  
Console Switch  
S/HEATER FRT  
POWER OUTLET 1  
Cigarette Lighter & Front Power Outlet  
7 55  
Maintenance  
Description  
Fuse rating  
10A  
Protected component  
B/UP LP  
B/UP LP Relay  
DR LOCK  
MODULE 5  
WIPER RR  
SUNROOF  
IGN 1  
15A  
Door Lock Relay, Tail Gate Relay, Door Unlock Relay  
7.5A  
15A  
BCM, PDM  
ICM Relay Box (Rear Wiper Relay), Rear Wiper Motor, Multifunction Switch (Wiper)  
15A  
Sunroof Motor  
20A  
E/R Fuse & Relay Box(ECU 2 7.5A, ABS 7.5A, TCU 2 7.5A)  
A/CON  
7.5A  
15A  
A/C Control Module  
S/HEATER RR  
P/WDW RH  
MODULE 3  
P/SEAT (DRV)  
PDM  
-
25A  
Power Window Main Switch, Passenger Power Window Switch, Rear Power Window Switch RH  
10A  
-
20A  
Driver Seat Manual Switch  
15A  
PDM  
P/WDW LH  
AMP  
25A  
Power Window Main Switch, Rear Power Window Switch LH  
AMP  
25A  
HTD MIRR  
SAFETY POWER WINDOW  
TPMS  
7.5A  
20A  
Rear Defogger Switch, Rear Defogger (+), Driver/Passenger Power Outside Mirror  
Driver Safety Power Window Module  
ATM Shift Lever, AWD ECM, Tire Pressure Monitoring Module  
ICM Relay Box(Flasher Sound Relay), BCM  
7.5A  
15A  
HAZARD  
7 56  
Maintenance  
Engine compartment main fuse panel  
Description  
MDPS  
Fuse rating  
Protected component  
80A  
60A  
40A  
40A  
40A  
40A  
EPS Control Module  
B+1  
I/P Junction Box(PDM 15A, DR LOCK 15A, HAZARD 15A, IPS 4, IPS 5, IPS 6, IPS 7)  
Multipurpose Check Connector, ESC Control Module  
EMS Box(TCU 1 15A, ECU 30A, A/CON 10A, F/PUMP 15A)  
Multipurpose Check Connector, ESC Control Module  
Blower Relay  
ABS 2  
EMS  
MULTI  
FUSE  
ABS 1  
BLOWER  
I/P Junction Box(P/SEAT(DRV) 20A, SAFETY POWER WINDOW 20A, TPMS 7.5A,  
Power Connector(AUDIO 1 10A, ROOM LP 10A))  
B+3  
60A  
B+2  
60A  
40A  
40A  
40A  
40A  
15A  
15A  
10A  
10A  
7.5A  
7.5A  
7.5A  
15A  
I/P Junction Box(Power Window Relay, SUNROOF 15A, AMP 25A, IPS 0, IPS 1, IPS 2, IPS 3)  
E/R Fuse & Relay Box(C/FAN LO Relay, C/FAN HI Relay)  
E/R Fuse & Relay Box(RR HTD Relay)  
C/FAN  
RR HTD  
IGN 1  
PDM Relay Box(IGN1 Relay), Ignition Switch  
IGN 2  
E/R Fuse & Relay Box(Statr Relay), PDM Relay Box(IGN2 Relay), Ignition Switch  
E/R Fuse & Relay Box(Horn Relay, B/A Horn Relay)  
E/R Fuse & Relay Box(Deicer Relay, RR HTD Relay)  
Stop Lamp Switch, ICM Relay Box(DBC Relay)  
HORN  
DEICER  
STOP LP  
B+ SENSOR  
TCU 2  
FUSE  
Batter Sensor  
Transaxle Range Switch(A/T), Vehicle Speed Sensor(M/T)  
Multipurpose Check Connector, ESC Control Module  
E/R Fuse & Relay Box(ATM P/N Relay), Mass Air Flow Sensor, PCM  
EMS Box(F/PUMP Relay)  
ABS  
ECU 2  
F/PUMP  
7 57  
Maintenance  
Description  
Fuse rating  
Protected component  
E/R Fuse & Relay Box(C/FAN HI, LO Relay), EMS Box(F/PUMP Relay),  
Oxygen Sensor (UP, DOWN), PCM  
SENSOR 4  
15A  
SENSOR 3  
SENSOR 2  
TCU 1  
10A  
10A  
15A  
10A  
EMS Box(A/CON Relay), Injector(#1, #2, #3, #4)  
-
PCM  
FUSE  
A/CON  
EMS Box(A/CON Relay)  
Crankshaft Position Sensor, Camshaft Position Sensor #1/2, Oil Control Valve #1/2,  
Canister Purge Control Solenoid Valve, Variable Intake Manifold Valve, Canister Close Valve  
SENSOR 1  
10A  
ECU 1  
ECU  
20A  
30A  
Ignition Colil (#1, #2, #3, #4), Condenser  
EMS Box(Engine Control Relay)  
7 58  
Maintenance  
LIGHT BULBS  
WARNING - Working on  
the lights  
Prior to working on the light, firmly  
apply the parking brake, ensure  
that the ignition switch is turned to  
the LOCK position and turn off the  
lights to avoid sudden movement  
of the vehicle and burning your fin-  
gers or receiving an electric shock.  
CAUTION  
If you don’t have necessary tools,  
the correct bulbs and the expertise,  
consult an authorized HYUNDAI  
dealer. In many cases, it is difficult  
to replace vehicle light bulbs  
because other parts of the vehicle  
must be removed before you can  
get to the bulb. This is especially  
true if you have to remove the head-  
light assembly to get to the bulb(s).  
Removing/installing the headlight  
assembly can result in damage to  
the vehicle.  
OLM079029  
Use only the bulbs of the specified  
wattage.  
Headlight, position light, turn sig-  
nal light, side marker light and  
front fog light bulb replacement  
(1) Front turn signal light  
(2) Position light  
CAUTION  
✽
NOTICE  
Be sure to replace the burned-out  
bulb with one of the same wattage  
rating. Otherwise, it may cause  
damage to the fuse or electric  
wiring system.  
After heavy, driving rain or washing,  
headlight and taillight lenses could  
appear frosty. This condition is caused by  
the temperature difference between the  
lamp inside and outside. This is similar  
to the condensation on your windows  
inside your vehicle during the rain and  
doesn’t indicate a problem with your  
vehicle. If the water leaks into the lamp  
bulb circuitry, have the vehicle checked  
by an authorized HYUNDAI dealer.  
(3) Headlight (High/Low)  
(4) Front side marker light  
(5) Front fog light (if equipped)  
7 59  
Maintenance  
(Continued)  
• A bulb should be operated only  
when installed in a headlight.  
• If a bulb becomes damaged or  
cracked, replace it immediately  
and carefully dispose of it.  
• Wear eye protection when chang-  
ing a bulb. Allow the bulb to cool  
down before handling it.  
OHD076046  
OLM079030  
Headlight bulb  
1. Open the hood.  
2. Remove the headlight bulb cover by  
turning it counterclockwise.  
WARNING - Halogen bulbs  
3. Disconnect the headlight bulb socket-  
connector.  
• Halogen bulbs contain pressur-  
ized gas that will produce flying  
pieces of glass if broken.  
4. Unsnap the headlight bulb retaining  
wire by depressing the end and push-  
ing it upward.  
• Always handle them carefully,  
and avoid scratches and abra-  
sions. If the bulbs are lit, avoid  
contact with liquids.  
• Never touch the glass with bare  
hands. Residual oil may cause  
the bulb to overheat and burst  
when lit.  
(Continued)  
7 60  
Maintenance  
5. Remove the bulb from the headlight  
assembly.  
3. Insert a new bulb by inserting it into  
the socket and rotating it until it locks  
into place.  
6. Install a new headlight bulb and snap  
the headlight bulb retaining wire into  
position by aligning the wire with the  
groove on the bulb.  
4. Install the socket in the assembly by  
aligning the tabs on the socket with the  
slots in the assembly. Push the socket  
into the assembly and turn the socket  
clockwise.  
7. Connect the headlight bulb socket-  
connector.  
8. Install the headlight bulb cover by turn-  
ing it clockwise.  
Front fog light bulbs (if equipped)  
OLM079046  
If the light bulb is not operating, have the  
vehicle checked by an authorized  
HYUNDAI dealer.  
Turn signal light/Position light  
1. Remove the socket from the assembly  
by turning the socket counterclockwise  
until the tabs on the socket align with  
the slots on the assembly.  
2. Remove the bulb from the socket by  
pressing it in and rotating it counter-  
clockwise until the tabs on the bulb  
align with the slots in the socket. Pull  
the bulb out of the socket  
7 61  
Maintenance  
OLM079034  
OLM079031  
OLM079033  
Side repeater light replacement  
Rear combination light bulb  
replacement  
If the light bulb does not operate, have  
the vehicle checked by an authorized  
HYUNDAI dealer.  
(1) Stop and tail light  
(2) Rear turn signal light  
(3) Back-up light  
(4) Tail light  
(5) Rear side marker light  
OLM079035  
Outside light  
1. Open the tailgate.  
2. Loosen the light assembly retaining  
screws with a philips head screwdriver.  
3. Remove the rear combination light  
assembly from the body of the vehicle.  
7 62  
Maintenance  
OLM079036  
OLM079047  
OLM079038  
4. Remove the socket from the assembly  
by turning the socket counterclockwise  
until the tabs on the socket align with  
the slots on the assembly.  
Inside light  
1. Open the tailgate.  
3. Remove the socket from the assembly  
by turning the socket counterclockwise  
until the tabs on the socket align with  
the slots on the assembly.  
2. Remove the service cover using a flat-  
blade screwdriver.  
5. Remove the bulb from the socket by  
pressing it in and rotating it counter-  
clockwise until the tabs on the bulb  
align with the slots in the socket. Pull  
the bulb out of the socket.  
4. Remove the bulb from the socket by  
pressing it in and rotating it counter-  
clockwise until the tabs on the bulb  
align with the slots in the socket. Pull  
the bulb out of the socket.  
6. Insert a new bulb by inserting it into  
the socket and rotating it until it locks  
into place.  
5. Insert a new bulb by inserting it into  
the socket and rotating it until it locks  
into place.  
7. Install the socket in the assembly by  
aligning the tabs on the socket with the  
slots in the assembly. Push the socket  
into the assembly and turn the socket  
clockwise.  
6. Install the socket in the assembly by  
aligning the tabs on the socket with the  
slots in the assembly. Push the socket  
into the assembly and turn the socket  
clockwise.  
8. Reinstall the light assembly to the  
body of the vehicle.  
7. Install the service cover by putting it  
into the service hole.  
7 63  
Maintenance  
(A)  
(B)  
OLM079039  
OLM071061L  
OLM079055  
4.Loosen the retaining nuts and remove  
the spoiler.  
License plate light bulb replace-  
ment  
5.Remove the high mounted stop light  
assembly (A) after loosening the nuts  
and washer nozzle (B).  
1. Remove the lens by pressing the tabs.  
2. Remove the socket from the lens.  
3. Remove the bulb by pulling it straight  
out.  
6.Reinstall a new light assembly in the  
reverse order of removal.  
4. Install a new bulb in the socket and  
install the socket to the lens.  
5. Reinstall the lens securely.  
OLM071060L  
High mounted stop light  
replacement  
1.Open the tailgate.  
2.Gently remove the center cover of the  
rear tailgate trim.  
3.Disconnect the electrical connector.  
7 64  
Maintenance  
Map lamp  
Luggage room lamp (if equipped)  
Interior light bulb replacement  
1. Using a flat-blade screwdriver, gently  
pry the lens from the interior light  
housing.  
2. Remove the bulb by pulling it straight  
out.  
WARNING  
Prior to working on the Interior  
Lights, ensure that the “OFF” but-  
ton is depressed to avoid burning  
your fingers or receiving an electric  
shock.  
Sunvisor lamp  
Glove box lamp (if equipped)  
3. Install a new bulb in the socket.  
4. Align the lens tabs with the interior  
light housing notches and snap the  
lens into place.  
CAUTION  
Use care not to dirty or damage  
lens, lens tab, and plastic housings.  
Room lamp  
OLM079040/OXM079041/OLM079042/  
OLM079044/OLM079045  
7 65  
Maintenance  
APPEARANCE CARE  
Even prompt washing with plain water  
may not completely remove all these  
deposits. A mild soap, safe for use on  
painted surfaces, may be used.  
Exterior care  
WARNING - Wet brakes  
Exterior general caution  
After washing the vehicle, test the  
brakes while driving slowly to see if  
they have been affected by water. If  
braking performance is impaired,  
dry the brakes by applying them  
lightly while maintaining a slow for-  
ward speed.  
It is very important to follow the label  
directions when using any chemical  
cleaner or polish. Read all warning and  
caution statements that appear on the  
label.  
After washing, rinse the vehicle thor-  
oughly with lukewarm or cold water. Do  
not allow soap to dry on the finish.  
CAUTION  
Finish maintenance  
Washing  
To help protect your vehicle’s finish from  
rust and deterioration, wash it thoroughly  
and frequently at least once a month with  
lukewarm or cold water.  
• Do not use strong soap, chemical  
detergents or hot water, and do  
not wash the vehicle in direct  
sunlight or when the body of the  
vehicle is warm.  
• Be careful when washing the side  
windows of your vehicle.  
If you use your vehicle for off-road driv-  
ing, you should wash it after each off-  
road trip. Pay special attention to the  
removal of any accumulation of salt, dirt,  
mud, and other foreign materials. Make  
sure the drain holes in the lower edges of  
the doors and rocker panels are kept  
clear and clean.  
Especially, with high-pressure  
water.Water may leak through the  
windows and wet the interior.  
• To prevent damage to the plastic  
parts, do not clean with chemical  
solvents or strong detergents.  
Insects, tar, tree sap, bird droppings,  
industrial pollution and similar deposits  
can damage your vehicle’s finish if not  
removed immediately.  
7 66  
Maintenance  
Waxing  
Finish damage repair  
A good coat of wax is a barrier between  
your paint and contaminate. Keeping a  
good coat of wax on your vehicle will help  
protect it.  
Deep scratches or stone chips in the  
painted surface must be repaired  
promptly. Exposed metal will quickly rust  
and may develop into a major repair  
expense.  
Wax the vehicle when water will no  
longer bead on the paint.  
Always wash and dry the vehicle before  
waxing. Use a good quality liquid or  
paste wax, and follow the manufacturer’s  
instructions. Wax all metal trim to protect  
it and to maintain its luster.  
✽
NOTICE  
If your vehicle is damaged and requires  
any metal repair or replacement, be sure  
the body shop applies anti-corrosion  
materials to the parts repaired or  
replaced.  
OJB037800  
Removing oil, tar, and similar materials  
with a spot remover will usually strip the  
wax from the finish. Be sure to re-wax  
these areas even if the rest of the vehicle  
does not yet need waxing.  
CAUTION  
• Water washing in the engine com-  
partment including high pressure  
water washing may cause the fail-  
ure of electrical circuits located in  
the engine compartment.  
CAUTION  
• Wiping dust or dirt off the body  
with a dry cloth will scratch the  
finish.  
• Never allow water or other liquids  
to come in contact with electri-  
cal/electronic components inside  
the vehicle as this may damage  
them.  
• Do not use steel wool, abrasive  
cleaners, or strong detergents  
containing highly alkaline or  
caustic agents on chrome-plated  
or anodized aluminum parts. This  
may result in damage to the pro-  
tective coating and cause discol-  
oration or paint deterioration.  
7 67  
Maintenance  
Bright-metal maintenance  
Underbody maintenance  
Aluminum wheel maintenance  
The aluminum wheels are coated with a  
clear protective finish.  
• To remove road tar and insects, use a  
tar remover, not a scraper or other  
sharp object.  
Corrosive materials used for ice and  
snow removal and dust control may col-  
lect on the underbody. If these materials  
are not removed, accelerated rusting can  
occur on underbody parts such as the  
fuel lines, frame, floor pan and exhaust  
system, even though they have been  
treated with rust protection.  
• Do not use any abrasive cleaner, pol-  
ishing compound, solvent, or wire  
brushes on aluminum wheels. They  
may scratch or damage the finish.  
• To protect the surfaces of bright-metal  
parts from corrosion, apply a coating of  
wax or chrome preservative and rub to  
a high luster.  
• Use only a mild soap or neutral deter-  
gent, and rinse thoroughly with water.  
Also, be sure to clean the wheels after  
driving on salted roads. This helps pre-  
vent corrosion.  
• During winter weather or in coastal  
areas, cover the bright metal parts with  
a heavier coating of wax or preserva-  
tive. If necessary, coat the parts with  
non-corrosive petroleum jelly or other  
protective compound.  
Thoroughly flush the vehicle underbody  
and wheel openings with lukewarm or  
cold water once a month, after off-road  
driving and at the end of each winter. Pay  
special attention to these areas because  
it is difficult to see all the mud and dirt. It  
will do more harm than good to wet down  
the road grime without removing it. The  
lower edges of doors, rocker panels, and  
frame members have drain holes that  
should not be allowed to clog with dirt;  
trapped water in these areas can cause  
rusting.  
• Avoid washing the wheels with high-  
speed car wash brushes.  
• Do not use any cleaners containing  
acid or acid detergents. It may damage  
and corrode the aluminum wheels  
coated with a clear protective finish.  
WARNING  
After washing the vehicle, test the  
brakes while driving slowly to see if  
they have been affected by water. If  
braking performance is impaired,  
dry the brakes by applying them  
lightly while maintaining a slow for-  
ward speed.  
7 68  
Maintenance  
High-corrosion areas  
Moisture breeds corrosion  
Corrosion protection  
Protecting your vehicle from corrosion  
If you live in an area where your vehicle  
is regularly exposed to corrosive materi-  
als, corrosion protection is particularly  
important. Some of the common causes  
of accelerated corrosion are road salts,  
dust control chemicals, ocean air and  
industrial pollution.  
Moisture creates the conditions in which  
corrosion is most likely to occur. For  
example, corrosion is accelerated by  
high humidity, particularly when tempera-  
tures are just above freezing. In such  
conditions, the corrosive material is kept  
in contact with the car surfaces by mois-  
ture that is slow to evaporate.  
By using the most advanced design and  
construction practices to combat corro-  
sion, we produces cars of the highest  
quality. However, this is only part of the  
job. To achieve the long-term corrosion  
resistance your vehicle can deliver, the  
owner's cooperation and assistance is  
also required.  
Mud is particularly corrosive because it is  
slow to dry and holds moisture in contact  
with the vehicle. Although the mud  
appears to be dry, it can still retain the  
moisture and promote corrosion.  
Common causes of corrosion  
The most common causes of corrosion  
on your car are:  
High temperatures can also accelerate  
corrosion of parts that are not properly  
ventilated so the moisture can be dis-  
persed. For all these reasons, it is par-  
ticularly important to keep your vehicle  
clean and free of mud or accumulations  
of other materials. This applies not only  
to the visible surfaces but particularly to  
the underside of the vehicle.  
• Road salt, dirt and moisture that is  
allowed to accumulate underneath the  
vehicle.  
• Removal of paint or protective coatings  
by stones, gravel, abrasion or minor  
scrapes and dents which leave unpro-  
tected metal exposed to corrosion.  
7 69  
Maintenance  
To help prevent corrosion  
You can help prevent corrosion from get-  
ting started by observing the following:  
• When cleaning underneath the vehicle,  
give particular attention to the compo-  
nents under the fenders and other  
areas that are hidden from view. Do a  
thorough job; just dampening the accu-  
mulated mud rather than washing it  
away will accelerate corrosion rather  
than prevent it. Water under high pres-  
sure and steam are particularly effec-  
tive in removing accumulated mud and  
corrosive materials.  
Keep paint and trim in good condition  
Scratches or chips in the finish should be  
covered with "touch-up" paint as soon as  
possible to reduce the possibility of cor-  
rosion. If bare metal is showing through,  
the attention of a qualified body and paint  
shop is recommended.  
Keep your car clean  
The best way to prevent corrosion is to  
keep your vehicle clean and free of cor-  
rosive materials. Attention to the under-  
side of the vehicle is particularly impor-  
tant.  
Bird droppings : Bird droppings are high-  
ly corrosive and may damage painted  
surfaces in just a few hours. Always  
remove bird droppings as soon as possi-  
ble.  
• When cleaning lower door panels,  
rocker panels and frame members, be  
sure that drain holes are kept open so  
that moisture can escape and not be  
trapped inside to accelerate corrosion.  
• If you live in a high-corrosion area —  
where road salts are used, near the  
ocean, areas with industrial pollution,  
acid rain, etc.—, you should take extra  
care to prevent corrosion. In winter,  
hose off the underside of your vehicle  
at least once a month and be sure to  
clean the underside thoroughly when  
winter is over.  
Don't neglect the interior  
Moisture can collect under the floor mats  
and carpeting to cause corrosion. Check  
under the mats periodically to be sure  
the carpeting is dry. Use particular care if  
you carry fertilizers, cleaning materials or  
chemicals in the vehicle.  
Keep your garage dry  
Don't park your car in a damp, poorly  
ventilated garage. This creates a favor-  
able environment for corrosion. This is  
particularly true if you wash your vehicle  
in the garage or drive it into the garage  
when it is still wet or covered with snow,  
ice or mud. Even a heated garage can  
contribute to corrosion unless it is well  
ventilated so moisture is dispersed.  
These should be carried only in proper  
containers and any spills or leaks should  
be cleaned up, flushed with clean water  
and thoroughly dried.  
7 70  
Maintenance  
Cleaning the upholstery and interior  
trim  
Vinyl  
Remove dust and loose dirt from vinyl  
with a whisk broom or vacuum cleaner.  
Clean vinyl surfaces with a vinyl cleaner.  
Cleaning the lap/shoulder belt web-  
bing  
Interior care  
Interior general precautions  
Clean the belt webbing with any mild  
soap solution recommended for cleaning  
upholstery or carpet. Follow the instruc-  
tions provided with the soap. Do not  
bleach or re-dye the webbing because  
this may weaken it.  
Prevent caustic solutions such as per-  
fume and cosmetic oil from contacting  
the dashboard because they may cause  
damage or discoloration. If they do con-  
tact the dashboard, wipe them off imme-  
diately. See the instructions for the prop-  
er way to clean vinyl.  
Fabric  
Remove dust and loose dirt from fabric  
with a whisk broom or vacuum cleaner.  
Clean with a mild soap solution recom-  
mended for upholstery or carpets.  
Remove fresh spots immediately with a  
fabric spot cleaner. If fresh spots do not  
receive immediate attention, the fabric  
can be stained and its color can be  
affected. Also, its fire-resistant properties  
can be reduced if the material is not  
properly maintained.  
Cleaning the interior window glass  
If the interior glass surfaces of the vehi-  
cle become fogged (that is, covered with  
an oily, greasy or waxy film), they should  
be cleaned with glass cleaner. Follow the  
directions on the glass cleaner container.  
CAUTION  
Never allow water or other liquids to  
come in contact with electrical/elec-  
tronic components inside the vehi-  
cle as this may damage them.  
CAUTION  
Do not scrape or scratch the inside  
of the rear window. This may result  
in damage to the rear window  
defroster grid.  
CAUTION  
When cleaning leather products  
(steering wheel, seats etc.), use  
neutral detergents or low alcohol  
content solutions. If you use high  
alcohol content solutions or  
acid/alkaline detergents, the color  
of the leather may fade or the sur-  
face may get stripped off.  
CAUTION  
Using anything but recommended  
cleaners and procedures may affect  
the fabric’s appearance and fire-  
resistant properties.  
7 71  
Maintenance  
EMISSION CONTROL SYSTEM  
The emission control system of your  
vehicle is covered by a written limited  
warranty. Please see the warranty infor-  
mation contained in the Owner’s  
Handbook & Warranty Information book-  
let in your vehicle.  
Caution for the Inspection and  
Maintenance Test (With Electronic  
Stability Control (ESC) system)  
1. Crankcase emission control  
system  
The positive crankcase ventilation sys-  
tem is employed to prevent air pollution  
caused by blow-by gases being emitted  
from the crankcase.This system supplies  
fresh filtered air to the crankcase through  
the air intake hose. Inside the crankcase,  
the fresh air mixes with blow-by gases,  
which then pass through the PCV valve  
into the induction system.  
• To prevent the vehicle from misfir-  
ing during dynamometer testing,  
turn the Electronic Stability Control  
(ESC) system off by pressing the  
ESC switch.  
Your vehicle is equipped with an emis-  
sion control system to meet all applicable  
emission regulations.  
• After dynamometer testing is com-  
pleted, turn the ESC system back on  
by pressing the ESC switch again.  
There are three emission control sys-  
tems, as follows.  
(1) Crankcase emission control system  
(2) Evaporative emission control system  
(3) Exhaust emission control system  
2. Evaporative emission control  
(including ORVR: Onboard  
Refueling Vapor Recovery)  
system  
In order to assure the proper function of  
the emission control systems, it is rec-  
ommended that you have your vehicle  
inspected and maintained by an author-  
ized HYUNDAI dealer in accordance with  
the maintenance schedule in this manu-  
al.  
The Evaporative Emission Control  
System is designed to prevent fuel  
vapors from escaping into the atmos-  
phere.  
(The ORVR system is designed to allow  
the vapors from the fuel tank to be  
loaded into a canister while refueling at  
the gas station, preventing the escape of  
fuel vapors into the atmosphere.)  
7 72  
Maintenance  
Canister  
3. Exhaust emission control  
system  
Fuel vapors generated inside the fuel  
tank are absorbed and stored in the  
onboard canister. When the engine is  
running, the fuel vapors absorbed in the  
canister are drawn into the surge tank  
through the purge control solenoid valve.  
WARNING - Exhaust  
Engine exhaust gases contain car-  
bon monoxide (CO). Though color-  
less and odorless, it is dangerous  
and could be lethal if inhaled.  
Follow the instructions on this  
page to avoid CO poisoning.  
The Exhaust Emission Control System is  
a highly effective system which controls  
exhaust emissions while maintaining  
good vehicle performance.  
Vehicle modifications  
Purge Control Solenoid Valve (PCSV)  
This vehicle should not be modified.  
Modification of your vehicle could affect  
its performance, safety or durability and  
may even violate governmental safety  
and emissions regulations.  
The purge control solenoid valve is con-  
trolled by the Engine Control Module  
(ECM); when the engine coolant temper-  
ature is low during idling, the PCSV clos-  
es so that evaporated fuel is not taken  
into the engine. After the engine warms-  
up during ordinary driving, the PCSV  
opens to introduce evaporated fuel to the  
engine.  
CALIFORNIA PROPOSI-  
TION 65 WARNING  
Engine exhaust and a wide variety  
of automobile components and  
parts, including components found  
in the interior furnishings in a vehi-  
cle, contain or emit chemicals  
known to the State of California to  
cause cancer and birth defects and  
reproductive harm. In addition, cer-  
tain fluids contained in vehicles  
and certain products of component  
wear contain or emit chemicals  
known to the State of California to  
cause cancer and birth defects or  
other reproductive harm.  
In addition, damage or performance  
problems resulting from any modification  
may not be covered under warranty.  
Engine exhaust gas precautions (car-  
bon monoxide)  
• Carbon monoxide can be present with  
other exhaust fumes. Therefore, if you  
smell exhaust fumes of any kind inside  
your vehicle, have it inspected and  
repaired immediately. If you ever sus-  
pect exhaust fumes are coming into  
your vehicle, drive it only with all the  
windows fully open. Have your vehicle  
checked and repaired immediately.  
7 73  
Maintenance  
• Do not operate the engine in confined  
or closed areas (such as garages) any  
more than what is necessary to move  
the vehicle in or out of the area.  
Operating precautions for catalytic  
converters (if equipped)  
• Do not misuse or abuse the engine.  
Examples of misuse are coasting with  
the ignition off and descending steep  
grades in gear with the ignition off.  
WARNING - Fire  
• When the vehicle is stopped in an  
open area for more than a short time  
with the engine running, adjust the  
ventilation system (as needed) to draw  
outside air into the vehicle.  
• Do not operate the engine at high idle  
speed for extended periods (5 minutes  
or more).  
A hot exhaust system can ignite  
flammable items under your vehi-  
cle. Do not park, idle, or drive the  
vehicle over or near flammable  
objects, such as grass, vegetation,  
paper, leaves, etc.  
• Do not modify or tamper with any part  
of the engine or emission control sys-  
tem. All inspections and adjustments  
must be made by an authorized  
HYUNDAI dealer.  
• Never sit in a parked or stopped vehi-  
cle for any extended time with the  
engine running.  
Your vehicle is equipped with a catalytic  
converter emission control device.  
• When the engine stalls or fails to start,  
excessive attempts to restart the  
engine may cause damage to the  
emission control system.  
• Avoid driving with a extremely low fuel  
level. Running out of fuel could cause  
the engine to misfire, damaging the  
catalytic converter.  
Therefore, the following precautions  
must be observed:  
• Use only UNLEADED FUEL for gaso-  
line engines.  
Failure to observe these precautions  
could result in damage to the catalytic  
converter and to your vehicle.  
Additionally, such actions could void your  
warranties.  
• Do not operate the vehicle when there  
are signs of engine malfunction, such  
as misfire or a noticeable loss of per-  
formance.  
7 74  
Maintenance  
CALIFORNIA PERCHLORATE NOTICE  
Perchlorate Material-special handling  
may apply, See www.dtsc.ca.gov/haz-  
ardouswaste/perchlorate.  
Notice to California Vehicle Dismantlers:  
Perchlorate containing materials, such as  
air bag inflators, seatbelt pretensioners  
and keyless remote entry batteries, must  
be disposed of according to Title 22  
California Code of Regulations Section  
67384.10 (a).  
7 75  

Related Topics

ENGINE COMPARTMENT MAINTENANCE SERVICES OWNER MAINTENANCE SCHEDULED MAINTENANCE SERVICE EXPLANATION OF SCHEDULED MAINTENANCE ITEMS ENGINE OIL ENGINE COOLANT BRAKE/CLUTCH (IF EQUIPPED) FLUID WASHER FLUID PARKING BRAKE AIR CLEANER CLIMATE CONTROL AIR FILTER WIPER BLADES BATTERY TIRES AND WHEELS FUSES LIGHT BULBS EMISSION CONTROL SYSTEM CALIFORNIA PERCHLORATE NOTICE

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot