Get Features of your vehicle Guide for Kia Picanto 4 Door First Generation (2004-2010)

Keys / 4-2

Remote keyless entry / 4-4

Theft-alarm system / 4-6

Door locks / 4-8

Tailgate / 4-11

Windows / 4-12

Hood / 4-15

Fuel filler lid / 4-17

Features of your vehicle

4

Steering wheel / 4-19

Mirrors / 4-22

Instrument cluster / 4-25

Rear parking assist system / 4-38

Hazard warning flasher / 4-41

Lighting / 4-41

Wipers and washers / 4-46

Interior light / 4-50

Defroster / 4-51

Manual climate control system / 4-52

Automatic climate control system / 4-60

Windshield defrosting and defogging / 4-67

Storage compartment / 4-70

Interior features / 4-72

Audio system / 4-77

Features of your vehicle

KEYS

Type A

Type B

WARNING - Ignition key

Leaving children unattended in a

vehicle with the ignition key is dan-

gerous even if the key is not in the

ignition switch. Children copy

adults and they could place the key

in the ignition switch. The ignition

key would enable children to oper-

ate power windows or other con-

trols, or even make the vehicle

move, which could result in serious

bodily injury or even death. Never

leave the keys in your vehicle with

unsupervised children.

OUN046100L

OUN026060/OSA049001L

D010100AUN

D010200AUN

Key operations

Used to start the engine, lock and unlock

the doors.

Record your key number

The key code number is stamped on the

bar code tag attached to the key set.

Should you lose your keys, this number

will enable an authorized KIA dealer to

duplicate the keys easily. Remove the bar

code tag and store it in a safe place. Also,

record the code number and keep it in a

safe place (not in the vehicle).

WARNING

Type B

To unfold the key, press the release but-

ton then the key will unfold automatically.

Use only KIA original parts for the

ignition key in your vehicle. If an

aftermarket key is used, the ignition

switch may not return to ON after

START. If this happens, the starter

will continue to operate causing

damage to the starter motor and

possible fire due to excessive cur-

rent in the wiring.

To fold the key, fold the key manually

while pressing the release button.

CAUTION

Do not fold the key without press-

ing the release button. This may

damage the key.

4 2

Features of your vehicle

D010300CUN

✽

NOTICE

If you need additional keys or lose your

keys, consult an authorized KIA dealer.

Immobilizer system (if equipped)

WARNING

In order to prevent theft of your

vehicle, do not leave spare keys

anywhere in your vehicle. Your

Immobilizer password is a cus-

tomer unique password and should

be kept confidential. Do not leave

this number anywhere in your vehi-

cle.

Your vehicle may be equipped with an

electronic engine immobilizer system to

reduce the risk of unauthorized vehicle

use.

CAUTION

The transponder in your ignition

key is an important part of the

immobilizer system. It is designed

to give years of trouble-free service,

however you should avoid expo-

sure to moisture, static electricity

and rough handling. Immobilizer

system malfunction could occur.

Your immobilizer system is comprised of

a small transponder in the ignition key

and electronic devices inside the vehicle.

With the immobilizer system, whenever

you insert your ignition key into the igni-

tion switch and turn it to ON, it checks

and determines and verifies if the ignition

key is valid or not.

✽

NOTICE

When starting the engine, do not use the

key with other immobilizer keys around.

Otherwise the engine may not start or

may stop soon after it starts. Keep each

key separate in order to avoid a starting

malfunction.

If the key is determined to be valid, the

engine will start.

If the key is determined to be invalid, the

engine will not start.

CAUTION

Do not change, alter or adjust the

immobilizer system because it

could cause the immobilizer sys-

tem to malfunction and should only

be serviced by an authorized KIA

dealer.

To deactivate the immobilizer sys-

tem:

CAUTION

Insert the ignition key into the key cylin-

der and turn it to the ON position.

Do not put metal accessories near

the ignition switch. Metal acces-

sories may interrupt the transpon-

der signal and may prevent the

engine from being started.

Malfunctions caused by improper

alterations, adjustments or modifi-

cations to the immobilizer system

are not covered by your vehicle

manufacturer warranty.

To activate the immobilizer system:

Turn the ignition key to the OFF position.

The immobilizer system activates auto-

matically. Without a valid ignition key for

your vehicle, the engine will not start.

4 3

Features of your vehicle

REMOTE KEYLESS ENTRY (IF EQUIPPED)

D020200ASA

Unlock (2)

All doors (and tailgate) are unlocked if

Transmitter precautions

the unlock button is pressed when both

front doors are locked.

✽

NOTICE

The transmitter will not work if any of

following occur:

The hazard warning lights will blink twice

again to indicate that all doors (and tail-

gate) are unlocked.

• The ignition key is in the ignition

switch.

After pressing this button, the doors (and

tailgate) will be locked automatically

unless you open any door within 30 sec-

onds.

• You exceed the operating distance

limit (about 5 m [16 feet]).

• The battery in the transmitter is

weak.

• Other vehicles or objects may be

blocking the signal.

OSA049002

Remote keyless entry system

operations

• The weather is extremely cold.

• The transmitter is close to a radio

transmitter such as a radio station or

an airport which can interfere with

normal operation of the transmitter.

When the transmitter does not work

correctly, open and close the door with

the ignition key. If you have a problem

with the transmitter, contact an author-

ized KIA dealer.

Lock (1)

All doors (and tailgate) are locked if the

lock button is pressed when a front door

is unlocked.

If all doors (and tailgate) are closed, the

hazard warning lights blink once to indi-

cate that all doors (and tailgate) are

locked.

However, if any door (or tailgate) remains

open, the hazard warning lights will not

operate. If all doors (and tailgate) are

closed after the lock button is pressed,

the hazard warning lights blink.

CAUTION

Keep the transmitter away from

water or any liquid. If the keyless

entry system is inoperative due to

exposure to water or liquids, it will

not be covered by your manufactur-

er vehicle warranty.

4 4

Features of your vehicle

CAUTION

Changes or modifications not

expressly approved by the party

responsible for compliance could

void the user’s authority to operate

the equipment. If the keyless entry

system is inoperative due to

changes or modifications not

expressly approved by the party

responsible for compliance, it will

not be covered by your manufactur-

er’s vehicle warranty.

• The keyless entry system trans-

mitter is designed to give you

years of trouble-free use, howev-

er it can malfunction if exposed to

moisture or static electricity. If

you are unsure how to use your

transmitter or replace the battery,

contact an authorized KIA dealer.

• Using the wrong battery can

cause the transmitter to malfunc-

tion. Be sure to use the correct

battery.

OED039003A

D020300ASA

• To avoid damaging the transmit-

ter, don't drop it, get it wet, or

expose it to heat or sunlight.

Battery replacement

The transmitter uses a 3 volt lithium bat-

tery which will normally last for several

years. When replacement is necessary,

use the following procedure.

1. Insert a slim tool into the slot and gen-

tly pry open the transmitter center

cover.

CAUTION

An inappropriately disposed bat-

tery can be harmful to the environ-

ment and human health.

Dispose the battery according to

your local law(s) or regulation.

2. Replace the battery with new one.

When replacing the battery, make sure

the battery positive “+” symbol faces

up as indicated in the illustration.

3. Install the battery in the reverse order

of removal.

For transmitter replacement, see an

authorized KIA dealer to reprogram the

transmitter.

4 5

Features of your vehicle

THEFT-ALARM SYSTEM (IF EQUIPPED)

D030100ASA

✽

NOTICE

Armed stage

Park the car and stop the engine. Arm

the system as described below.

The theft-alarm system by the key can

be activated by an authorized KIA deal-

er.

Armed

stage

1. Remove the ignition key from the igni-

tion switch and exit the vehicle.

If you want this feature, consult an

authorized KIA dealer.

2. Make sure that all doors (and tailgate)

and engine hood are closed and

latched.

Do not arm the system until all pas-

sengers have left the vehicle. If the

system is armed while a passenger(s)

remains in the vehicle, the alarm may

be activated when the remaining pas-

senger(s) leave the vehicle.

Theft-alarm

stage

Disarmed

stage

3. Lock the doors using the transmitter of

the keyless entry system.

After completion of the steps above, the

hazard warning lights will blink once to

indicate that the system is armed.

D030000AEN

This system is designed to provide pro-

tection from unauthorized entry into the

car. This system is operated in three

stages: the first is the "Armed" stage, the

second is the "Theft-alarm" stage, and

the third is the "Disarmed" stage. If trig-

gered, the system provides an audible

alarm with blinking of the hazard warning

lights.

If any door (or tailgate) or engine hood

remains open, the hazard warning lights

will not operate and the theft-alarm will

not arm. If all doors (and tailgate) and

engine hood are closed after the lock

button is pressed, the hazard warning

lights will blink once and the theft-alarm

system will be armed.

4 6

Features of your vehicle

D030200AUN-EE

D030400ASA

CAUTION

Theft-alarm stage

Disarmed stage

Do not change, alter or adjust the

theft-alarm system because it could

cause the theft-alarm system to

malfunction and should only be

serviced by an authorized KIA deal-

er.

The alarm will be activated if any of the

following occurs while the system is

armed.

The system will be disarmed when the

doors (and tailgate) are unlocked with the

transmitter.

• A front or rear door is opened without

using the transmitter.

After depressing the unlock button, the

hazard warning lights will blink twice to

indicate that the system is disarmed.

• The tailgate is opened without using

the transmitter.

• The engine hood is opened.

Malfunctions caused by improper

alterations, adjustments or modifi-

cations to the theft-alarm system

are not covered by your vehicle

manufacturer warranty.

After depressing the unlock button, if any

door (or tailgate) is not opened within 30

seconds, the system will be rearmed.

The siren will sound and the hazard

warning lights will blink continuously for

approximately 30 seconds (for Europe,

Middle East Area and China), and repeat

the alarm 3 times unless the system is

disarmed (except Europe, Middle East

Area and China). To turn off the system,

unlock the doors with the transmitter.

✽

NOTICE

• Avoid trying to start the engine while

the alarm is activated. The vehicle

starting motor is disabled during the

theft-alarm stage.

If the system is not disarmed with the

transmitter, insert the key into the

ignition switch, turn the ignition

switch to the ON position and wait for

30 seconds. Then the system will be

disarmed. (Except China)

• If you lose your keys, consult your

authorized KIA dealer.

4 7

Features of your vehicle

DOOR LOCKS

• Doors can also be locked and

unlocked with the transmitter. (if

equipped)

• Once the doors are unlocked, they may

be opened by pulling the door handle.

Unlock

• When closing the door, push the door

by hand. Make sure that doors are

closed securely.

Lock

✽

NOTICE

• In cold and wet climates, door lock

and door mechanisms may not work

properly due to freezing conditions.

• If the door is locked/unlocked multi-

ple times in rapid succession with

either the vehicle key or door lock

switch, the system may stop operating

temporarily in order to protect the

circuit and prevent damage to system

components.

OSA047003

OSA047004

D050100ASA

• To lock a door without the key, push the

inside door lock lever (1) to the “Lock”

position and close the door (2).

Operating door locks from out-

side the vehicle

• If you lock the door with the driver’s

door lock lever (1), all vehicle doors will

lock automatically. (if equipped with

central door lock system)

• Turn the key toward the rear of the

vehicle to unlock and toward the front

of the vehicle to lock.

• If you lock/unlock the driver’s door with

a key, all vehicle doors will lock/unlock

automatically. (if equipped with central

door lock system)

✽

NOTICE

Always remove the ignition key, engage

the parking brake, close all windows

and lock all doors when leaving your

vehicle unattended.

4 8

Features of your vehicle

WARNING - Doors

WARNING - Unlocked

vehicles

• The doors should always be fully

closed and locked while the vehi-

cle is in motion to prevent acci-

dental opening of the door.

Locked doors will also discour-

age potential intruders when the

vehicle stops or slows.

Leaving your vehicle unlocked can

invite theft or possible harm to you

or others from someone hiding in

your vehicle while you are gone.

Always remove the ignition key,

engage the parking brake, close all

windows and lock all doors when

leaving your vehicle unattended.

Unlock

Lock

• Be careful when opening doors

and watch for vehicles, motorcy-

cles, bicycles or pedestrians

approaching the vehicle in the

path of the door. Opening a door

when something is approaching

can cause damage or injury.

OSA047005

Operating door locks from inside

the vehicle

WARNING - Unattended

children

D050201ASA

An enclosed vehicle can become

extremely hot, causing death or

severe injury to unattended chil-

dren or animals who cannot escape

the vehicle. Furthermore, children

might operate features of the vehi-

cle that could injure them, or they

could encounter other harm, possi-

bly from someone gaining entry to

the vehicle. Never leave children or

animals unattended in your vehicle.

With the door lock lever

• To unlock a door, pull the door lock

lever (1) to the “Unlock” position.

• To lock a door, push the door lock lever

(1) to the “Lock” position.

• To open a door, pull the door handle

(2) outward.

• If you lock/unlock the front door with

the door lock lever, all vehicle doors

will lock/unlock automatically. (if

equipped with central door lock sys-

tem)

4 9

Features of your vehicle

3. Close the rear door.

To open the rear door, pull the outside

door handle.

D050300AEN

Impact sensing door unlock sys-

tem (if equipped)

Even though the doors may be unlocked,

the rear door will not open by pulling the

inner door handle (1) until the rear door

All doors will be automatically unlocked

when an impact causes the air bags to

deploy.

child safety lock is unlocked (

).

WARNING - Rear door

locks

If children accidentally open the

rear doors while the vehicle is in

motion, they could fall out and be

severely injured or killed. To pre-

vent children from opening the rear

doors from the inside, the rear door

safety locks should be used when-

ever children are in the vehicle.

OSA047006

D050500ASA

Child-protector rear door lock

The child safety lock is provided to help

prevent children from accidentally open-

ing the rear doors from inside the vehicle.

The rear door safety locks should be

used whenever children are in the vehi-

cle.

1. Open the rear door.

2. Push the child safety lock located on

the rear edge of the door to the lock

position. When the child safety lock is

in the lock (

) position, the rear door

will not open even though the inner

door handle is pulled.

4 10

Features of your vehicle

TAILGATE

D070200AUN

✽

NOTICE

Closing the tailgate

In cold and wet climates, door lock and

door mechanisms may not work proper-

ly due to freezing conditions.

To close the tailgate, lower and push

down the tailgate firmly. Make sure that

the tailgate is securely latched.

Lock

Unlock

WARNING

WARNING - Exhaust

fumes

If you drive with the tailgate open,

you will draw dangerous exhaust

fumes into your vehicle which can

cause serious injury or death to

vehicle occupants.

The tailgate swings upward. Make

sure no objects or people are near

the rear of the vehicle when open-

ing the tailgate.

OSA0470215

D070100ASA

CAUTION

If you must drive with the tailgate

open, keep the air vents and all win-

dows open so that additional out-

side air comes into the vehicle.

Opening the tailgate

Make certain that you close the tail-

gate before driving your vehicle.

Possible damage may occur to the

tailgate lift cylinders and attached

hardware if the tailgate is not

closed prior to driving.

• The tailgate is locked or unlocked by

turning the key to the "Lock" or

"Unlock" position.

• The tailgate is locked or unlocked

when all doors are locked or unlocked

with the key, transmitter or driver's door

lock lever. (if equipped with central

door lock system)

WARNING - Rear cargo

area

Occupants should never ride in the

rear cargo area where no restraints

are available. To avoid injury in the

event of an accident or sudden

stops, occupants should always be

properly restrained.

• If unlocked, the tailgate can be opened

by pressing the handle and than

pulling up the hatch.

4 11

Features of your vehicle

WINDOWS

D080000APA

(1) Driver’s door power window switch

(2) Front passenger’s door power win-

dow switch

(3) Rear door (left) power window

switch*

(4) Rear door (right) power window

switch*

(5) Window opening and closing

(6) Automatic power window down*

(Driver’s window)

(7) Power window lock button*

* : if equipped

✽

NOTICE

In cold and wet climates, power win-

dows may not work properly due to

freezing conditions.

OSA049007

4 12

Features of your vehicle

D080100AUN

D080101AUN

D080102AUN

Window opening and closing

Auto down window (Driver's window)

(if equipped)

Power windows (if equipped)

The driver’s door has a master power

window switch that controls all the win-

dows in the vehicle.

The ignition switch must be in the ON

position for power windows to operate.

Depressing the power window switch

momentarily to the second detent posi-

tion (6) completely lowers the window

even when the switch is released.To stop

the window at the desired position while

the window is in operation, pull up the

switch to the opposite direction of the

movement.

Each door has a power window switch

that controls the door's window. The driv-

er has a power window lock switch which

can block the operation of passenger

windows.

To open or close a window, press down

or pull up the front portion of the corre-

sponding switch to the first detent posi-

tion (5).

The power windows can be operated for

approximately 30 seconds after the igni-

tion key is removed or turned to the ACC

or LOCK position. However, if the front

doors are opened, the power windows

cannot be operated within the 30 second

period after the ignition key is removed (if

equipped).

✽

NOTICE

While driving with the rear windows

down or with the sunroof (if equipped) in

an open(or partially open position), your

vehicle may demonstrate a wind buffet-

ing or pulsation noise. This noise is a

normal occurrence and can be reduced

or eliminated by taking the following

actions. If the noise occurs with one or

both of the rear windows down, partial-

ly lower both front windows approxi-

mately one inch. If you experience the

noise with the snroof open, slightly

reduce the size of the sunroof opening.

4 13

Features of your vehicle

CAUTION

WARNING - Windows

• NEVER leave the ignition key in

the vehicle.

• To prevent possible damage to

the power window system, do not

open or close two windows or

more at the same time. This will

also ensure the longevity of the

fuse.

• NEVER leave any child unattend-

ed in the vehicle. Even very

young children may inadvertently

cause the vehicle to move, entan-

gle themselves in the windows,

or otherwise injure themselves or

others.

• Never try to operate the main

switch on the driver's door and

the individual door window

switch in opposing directions at

the same time. If this is done, the

window will stop and cannot be

opened or closed.

• Always double check to make

sure all arms, hands, head and

other obstructions are safely out

of the way before closing a win-

dow.

OSA0470217

D080104ASA

Power window lock button

(if equipped)

• The driver can disable the power win-

dow switches on the passenger doors

by depressing the power window lock

button located on the driver’s door to

the LOCK position (pressed).

• Do not allow children play with

the power windows. Keep the dri-

ver’s door power window lock

switch in the LOCK position

(pressed). Serious injury can

result from unintentional window

operation by the child.

• When the power window lock button

is in the LOCK position (pressed),

the driver’s master control cannot

operate the passenger door power

windows.

• Do not extend face or arms out-

side through the window opening

while driving.

4 14

Features of your vehicle

HOOD

B050A01E

OSA0470219

OSA047020

D080200APA

D090100ASA

2. Go to the front of the vehicle, raise the

hood slightly, pull the secondary latch

(1) inside of the hood center and lift

the hood (2).

Opening the hood

Manual windows (if equipped)

1. Pull the release lever to unlatch the

hood. The hood should pop open

slightly.

To raise or lower the window, turn the

window regulator handle clockwise or

counterclockwise.

WARNING

When opening or closing the win-

dows, make sure your passenger's

arms, hands and body are safely

out of the way.

4 15

Features of your vehicle

D090200AUN

Closing the hood

1. Before closing the hood, check the fol-

lowing:

WARNING

• Always double check to be sure

that the hood is firmly latched

before driving away. If it is not

latched, the hood could open

while the vehicle is being driven,

causing a total loss of visibility,

which might result in an accident.

• All filler caps in the engine compart-

ment must be correctly installed.

• Gloves, rags or any other com-

bustible material must be removed

from the engine compartment.

• The support rod must be inserted

completely into the hole provided

in the hood whenever you inspect

the engine compartment.This will

prevent the hood from falling and

possibly injuring you.

2. Return the support rod to its clip to

prevent it from rattling.

3. Lower the hood until it is about 30 cm

(1 ft.) above the closed position and let

it drop. Make sure that it locks into

place.

OSA047008

3. Lift the hood and hold it open with the

support rod by inserting the free end of

the rod into the slot (1).

• Do not move the vehicle with the

hood raised. The view will be

blocked and the hood could fall

or be damaged.

WARNING

WARNING - Hot parts

• Before closing the hood, ensure

that all obstructions are removed

from the hood opening. Closing

the hood with an obstruction

present in the hood opening may

result in property damage or

severe personal injury.

Grasp the support rod in the area

wrapped in plastic. The plastic will

help prevent you from being burned

by hot metal when the engine is

hot.

• Do not leave gloves, rags or any

other combustible material in the

engine compartment. Doing so

may cause a heat-induced fire.

4 16

Features of your vehicle

FUEL FILLER LID

D100200ASA

Closing the fuel filler lid

1. To install the cap, turn it clockwise until

the cap is securely tightened.

2. Close the fuel filler lid and push it light-

ly and make sure that it is securely

closed.

D100300AUN

WARNING - Refueling

• If pressurized fuel sprays out, it

can cover your clothes or skin

and thus subject you to the risk

of fire and burns. Always remove

the fuel cap carefully and slowly.

If the cap is venting fuel or if you

hear a hissing sound, wait until

the condition stops before com-

pletely removing the cap.

OSA047022

OSA047009

D100100ASA

1. Stop the engine.

Opening the fuel filler lid

2. To open the fuel filler lid, pull the fuel

filler lid opener up.

3. Pull open the fuel filler lid (1).

The fuel filler lid must be opened from

inside the vehicle by pulling up the fuel

filler lid opener located on the front floor

area under the driver’s seat.

4. To remove the cap, turn the fuel tank

cap (2) counterclockwise.

5. Refuel as needed.

✽

NOTICE

• Do not "top off" after the nozzle

automatically shuts off when

refueling.

If the fuel filler lid does not open

because ice has formed around it, tap

lightly or push on the lid to break the ice

and release the lid. Do not pry on the lid.

If necessary, spray around the lid with

an approved de-icer fluid (do not use

radiator anti-freeze) or move the vehicle

to a warm place and allow the ice to

melt.

• Always check that the fuel cap is

installed securely to prevent fuel

spillage in the event of an acci-

dent.

4 17

Features of your vehicle

(Continued)

• When using

WARNING - Refueling dan-

gers

• Do not get back into a vehicle

once you have begun refueling

since you can generate static

electricity by touching, rubbing

or sliding against any item or fab-

ric (polyester, satin, nylon, etc.)

capable of producing static elec-

tricity. Static electricity discharge

can ignite fuel vapors resulting in

rapid burning. If you must re-

enter the vehicle, you should

once again eliminate potentially

dangerous static electricity dis-

charge by touching a metal part

of the vehicle, away from the fuel

filler neck, nozzle or other gaso-

line source.

an

approved

portable fuel container, be sure to

place the container on the

ground prior to refueling. Static

electricity discharge from the

container can ignite fuel vapors

causing a fire. Once refueling has

begun, contact with the vehicle

should be maintained until the

filling is complete.

Automotive fuels are flammable

materials. When refueling, please

note the following guidelines care-

fully. Failure to follow these guide-

lines may result in severe personal

injury, severe burns or death by fire

or explosion.

• Read and follow all warnings

posted at the gas station facility.

Use only approved portable plas-

tic fuel containers designed to

carry and store gasoline.

• Before refueling note the location

of the Emergency Gasoline Shut-

Off, if available, at the gas station

facility.

• Do not use cellular phones while

refueling. Electric current and/or

electronic interference from cel-

lular phones can potentially

ignite fuel vapors causing a fire.

• Before touching the fuel nozzle,

you should eliminate potentially

dangerous static electricity dis-

charge by touching another metal

part of the vehicle, a safe dis-

tance away from the fuel filler

neck, nozzle, or other gas source.

(Continued)

• When refueling, always shut the

engine off. Sparks produced by

electrical components related to

the engine can ignite fuel vapors

causing a fire. Once refueling is

complete, check to make sure the

filler cap and filler door are

securely closed, before starting

the engine.

(Continued)

4 18

Features of your vehicle

STEERING WHEEL

D130100AHM

(Continued)

CAUTION

Power steering (if equipped)

• DO NOT use matches or a lighter

and DO NOT SMOKE or leave a lit

cigarette in your vehicle while at

a gas station especially during

refueling. Automotive fuel is

highly flammable and can, when

ignited, result in fire.

• Make sure to refuel your vehicle

according to the "Fuel require-

ments" suggested in section 1.

Power steering uses energy from the

engine to assist you in steering the vehi-

cle. If the engine is off or if the power

steering system becomes inoperative,

the vehicle may still be steered, but it will

require increased steering effort.

• If the fuel filler cap requires

replacement, use only a genuine

KIA cap or the equivalent speci-

fied for your vehicle. An incorrect

fuel filler cap can result in a seri-

ous malfunction of the fuel sys-

tem or emission control system.

Should you notice any change in the

effort required to steer during normal

vehicle operation, have the power steer-

ing checked by an authorized KIA dealer.

• If a fire breaks out during refuel-

ing, leave the vicinity of the vehi-

cle, and immediately contact the

manager of the gas station and

then contact the local fire depart-

ment. Follow any safety instruc-

tions they provide.

• Do not spill fuel on the exterior

surfaces of the vehicle. Any type

of fuel spilled on painted surfaces

may damage the paint.

CAUTION

Never hold the steering wheel to the

extreme right or left for more than 5

seconds with the engine running.

Holding the steering wheel for more

than 5 seconds in either position

may cause damage to the power

steering pump.

• After refueling, make sure the fuel

cap is installed securely to pre-

vent fuel spillage in the event of

an accident.

4 19

Features of your vehicle

D130200ASA

✽

NOTICE

The following symptoms may occur dur-

ing normal vehicle operation:

Electric power steering

(if equipped)

• If the power steering drive belt breaks

or if the power steering pump mal-

functions, the steering effort will

greatly increase.

• If the vehicle is parked for extended

periods outside in cold weather (below

-10°C/14°F), the power steering may

require increased effort when the

engine is first started. This is caused

by increased fluid viscosity due to the

cold weather and does not indicate a

malfunction.

• The EPS warning light does not illu-

minate.

Power steering uses the motor to assist

you in steering the vehicle. If the engine

is off or if the power steering system

becomes inoperative, the vehicle may

still be steered, but it will require

increased steering effort.

• The steering effort is high immediate-

ly after turning the ignition switch on.

This happens as the system performs

the EPS system diagnostics. When the

diagnostics is completed, the steering

wheel will return to its normal condi-

tion.

• A click noise may be heard from the

EPS relay after the ignition switch is

turned to the ON or LOCK position.

• Motor noise may be heard when the

vehicle is at a stop or at a low driving

speed.

• The steering effort can suddenly

increase, if the operation of the EPS

system is stopped to prevent serious

accidents when the malfunction of

EPS system is detected by self-diagno-

sis.

The motor driven power steering is con-

trolled by power steering control unit

which sense the steering wheel torque,

steering wheel position and vehicle

speed to command the motor.

When this happens, increase the

engine RPM by depressing the accel-

erator until the RPM reaches 1,500

rpm then release or let the engine idle

for two or three minutes to warm up

the fluid.

The steering effort becomes heavier as

the vehicle’s speed increases and

becomes lighter as the vehicle’s speed

decreases for better control of the steer-

ing wheel.

Should you notice any change in the

effort required to steer during normal

vehicle operation, have the power steer-

ing checked by an authorized Kia dealer.

• The steering effort increases if the

steering wheel is rotated continuously

when the vehicle is not in motion.

However, after a few minutes, it will

return to its normal condition.

4 20

Features of your vehicle

D130300AUN

Tilt steering (if equipped)

Tilt steering allows you to adjust the

steering wheel before you drive. You can

also raise it to give your legs more room

when you exit and enter the vehicle.

The steering wheel should be positioned

so that it is comfortable for you to drive,

while permitting you to see the instru-

ment panel warning lights and gauges.

OSA040035

OAM049022

WARNING

D130301AEN

D130500AUN

• Never adjust the angle of the

steering wheel while driving. You

may lose steering control and

cause severe personal injury,

death or accidents.

To change the steering wheel angle, pull

down the lock-release lever (1), adjust

the steering wheel to the desired angle

(2), then pull up the lock-release lever to

lock the steering wheel in place. Be sure

to adjust the steering wheel to the

desired position before driving.

Horn

To sound the horn, press the horn sym-

bol on your steering wheel.

Check the horn regularly to be sure it

operates properly.

• After adjusting, push the steering

wheel both up and down to be

certain it is locked in position.

✽

NOTICE

To sound the horn, press the area indi-

cated by the horn symbol on your steer-

ing wheel (see illustration). The horn will

operate only when this area is pressed.

CAUTION

Do not strike the horn severely to

operate it, or hit it with your fist. Do

not press on the horn with a sharp-

pointed object.

4 21

Features of your vehicle

MIRRORS

D140100ASA

D140200BSA

Inside rearview mirror

Outside rearview mirror

Adjust the rearview mirror so that the

center view through the rear window is

seen. Make this adjustment before you

start driving.

Be sure to adjust the mirror angles

before driving.

Night

Your vehicle is equipped with both left-

hand and right-hand outside rearview

mirrors. The mirrors can be adjusted

remotely with the control levers or remote

switch, depending on the type of mirror

control installed.The mirror heads can be

folded back to prevent damage during an

automatic car wash or when passing

through a narrow street.

WARNING - Rear visibility

Do not place objects in the rear

seat or cargo area which would

interfere with your vision through

the rear window.

Day

OSA047037

D140101BSA

Day/night rearview mirror

(if equipped)

WARNING - Rearview mir-

rors

WARNING

Make this adjustment before you start

driving and while the day/night lever is in

the day position.

Do not adjust the rearview mirror

while the vehicle is moving. This

could result in loss of control, and

an accident which could cause

death, serious injury or property

damage.

• The passenger’s side outside

rearview mirror is convex. In

some countries, the driver’s side

outside rearview mirror is also

convex. Objects seen in the mir-

ror are closer than they appear.

Pull the day/night lever toward you to

reduce the glare from the headlights of

vehicles behind you during night driving.

Remember that you may lose some

rearview clarity in the night position.

• Use your interior rearview mirror

or direct observation to deter-

mine the actual distance of fol-

lowing vehicles when changing

lanes.

4 22

Features of your vehicle

CAUTION

Do not scrape ice off the mirror

face; this may damage the surface

of the glass. If ice should restrict

movement of the mirror, do not

force the mirror for adjustment. To

remove ice, use a deicer spray, or a

sponge or soft cloth with very warm

water.

OSA0470216

B510A01E

CAUTION

D140201APA

Manual remote control (if equipped)

To adjust an outside mirror, move the

control lever.

If the mirror is jammed with ice, do

not adjust the mirror by force. Use

an approved spray de-icer (not radi-

ator antifreeze) to release the

frozen mechanism or move the

vehicle to a warm place and allow

the ice to melt.

Adjusting the outside rearview mirror

Manual control (if equipped)

To adjust an outside mirror, move the mir-

ror.

WARNING

Do not adjust or fold the outside

rearview mirrors while the vehicle

is moving. This could result in loss

of control, and an accident which

could cause death, serious injury

or property damage.

4 23

Features of your vehicle

CAUTION

• The mirrors stop moving when

they reach the maximum adjust-

ing angles, but the motor contin-

ues to operate while the switch is

depressed. Do not press the

switch longer than necessary, the

motor may be damaged.

• Do not attempt to adjust the out-

side rearview mirror by hand.

Doing so may damage the parts.

OSA047042

B510E01E

D140202AEN

Electric remote control (if equipped)

Folding the outside rearview mirror

The electric remote control mirror switch

allows you to adjust the position of the

left and right outside rearview mirrors. To

adjust the position of either mirror, move

the lever (1) to R or L to select the right

side mirror or the left side mirror, then

press a corresponding point on the mirror

adjustment control to position the select-

ed mirror up, down, left or right.

To fold the outside rearview mirror, grasp

the housing of the mirror and then fold it

toward the rear of the vehicle.

After adjustment, put the switch into neu-

tral (center) position to prevent inadver-

tent adjustment.

4 24

Features of your vehicle

INSTRUMENT CLUSTER

■ Type A

1. Tachometer (if equipped)

2. Turn signal indicators

3. Speedometer

★

4. Engine temperature indicator

5. Warning and indicator lights

6. Odometer / Tripmeter

7. Tripmeter mode/reset button

8. Fuel gauge

■ Type B

★ : will say

if equipped with Passenger’s

front air bag ON/OFF switch

ꢀ The actual cluster in the vehicle may

differ from the illustration.

★

OSA049050L/OSA049052L

D150000BSA

4 25

Features of your vehicle

■ Type C

1. Tachometer (if equipped)

2. Turn signal indicators

3. Speedometer

4. Engine temperature indicator

5. Warning and indicator lights

6. Odometer / Tripmeter

7. Tripmeter mode/reset button

8. Fuel gauge

■ Type D

ꢀ The actual cluster in the vehicle may

differ from the illustration.

OSA049350L/OSA049351L

4 26

Features of your vehicle

Gasoline Engine

■ Type A

■ Type B

■ Type C

■ Type D

■ Type A

■ Type B

Diesel Engine

■ Type E

■ Type F

■ Type G

■ Type H

■ Type A

■ Type B

OSA0490360/OSA0400361/OSA0490362/OSA0490365/OSA0490364/OSA0400363/OSA0490366/OSA0400367

OSA0490368/OSA0490370/OSA0400369/OSA0400371

D150202ASA

Gauges

Tachometer (if equipped)

D150201AUN

The tachometer indicates the approxi-

mate number of engine revolutions per

minute (rpm).

Speedometer

The speedometer indicates the forward speed of the vehicle.

The speedometer is calibrated in kilometers per hour and/or miles per hour.

Use the tachometer to select the correct

shift points and to prevent lugging and/or

over-revving the engine.

4 27

Features of your vehicle

D150204AUN

When the door is open, or if the engine is

not started within 1 minute, the tachome-

ter pointer may move slightly to the ON

position with the engine OFF. This move-

ment is normal and will not affect the

accuracy of the tachometer once the

engine is running.

CAUTION

Fuel gauge

Avoid driving with a very low fuel

level. If you run out of fuel, it could

cause the engine to misfire and

result in excessive loading of the

catalytic converter.

The fuel gauge indicates the approxi-

mate amount of fuel remaining in the fuel

tank. The fuel tank capacity is given in sec-

tion 8. The fuel gauge is supplemented by

a low fuel warning light, which will illumi-

nate when the fuel tank is near empty.

On inclines or curves, the fuel gauge

pointer may fluctuate or the low fuel

warning light may come on earlier than

usual due to the movement of fuel in the

tank.

CAUTION

Do not operate the engine within

the tachometer's RED ZONE.

This may cause severe engine dam-

age.

WARNING - Fuel gauge

Running out of fuel can expose

vehicle occupants to danger.

You must stop and obtain addition-

al fuel as soon as possible after the

warning light comes on or when the

gauge indicator comes close to the

E level.

4 28

Features of your vehicle

Type A

OSA047056

Type B

OSA047057

OSA047058

Odometer

The odometer indicates the total dis-

tance the vehicle has been driven.

Tripmeter

TRIP A: Tripmeter A

TRIP B: Tripmeter B

The tripmeter indicates the distance of

individual trips selected by the driver.

Tripmeter A and B can be reset to 0 by

pressing the reset button for 1 second or

more, and then releasing.

OSA049056

D150205ASA

Odometer/Tripmeter

You can choose the odometer, tripmeter

A and tripmeter B by pressing the trip-

meter mode button.

4 29

Features of your vehicle

D150300AUN

D150301BSA

D150302AUN

Red

Engine temperature

indicator

Air bag warning light

(if equipped)

Warnings and indicators

All warning lights are checked by turning

the ignition switch ON (do not start the

engine). Any light that does not illuminate

should be checked by an authorized KIA

dealer.

The indicator shows the temperature of

the engine coolant when the ignition

switch is ON.

This warning light will illuminate for

approximately 6 seconds each time you

turn the ignition switch to the ON posi-

tion.

The red indicator illuminates if the tem-

perature of the engine coolant is above

120 3°C (248 5.5°F).

After starting the engine, check to make

sure that all warning lights are off. If any

are still on, this indicates a situation that

needs attention. When releasing the

parking brake, the brake system warning

light should go off. The fuel warning light

will stay on if the fuel level is low.

This light also comes on when the

Supplemental Restraint System (SRS) is

not working properly. If the air bag warn-

ing light does not come on, or continu-

ously remains on after operating for

about 6 seconds when you turned the

ignition switch to the ON position or start-

ed the engine, or if it comes on while

driving, have the SRS inspected by an

authorized KIA dealer.

Do not continue driving with an overheat-

ed engine. If your vehicle overheats, refer

to “Overheating” in the Index.

✽

NOTICE

If the red engine temperature indicator

illuminates, it indicates overheating that

may damage the engine.

4 30

Features of your vehicle

D150335APA

D150303AUN

Electronic brake force distri-

bution (EBD) system warning

light

If two warning lights illumi-

nate at the same time while

driving, your vehicle may

have a malfunction with the

ABS and EBD system.

Passenger’s front air bag

OFF indicator

(if equipped)

Anti-lock brake system

(ABS) warning light

(if equipped)

The passenger’s front air bag OFF indi-

cator illuminates for about 4 seconds

after the ignition switch is turned to the

ON position.

This light illuminates if the ignition switch

is turned ON and goes off in approxi-

mately 3 seconds if the system is operat-

ing normally.

In this case, your ABS and regular brake

system may not work normally. Have the

vehicle checked by an authorized KIA

dealer as soon as possible.

The passenger’s front air bag OFF indi-

cator also comes on when the passen-

ger’s front air bag ON/OFF switch is set

to the OFF position and turns off when

the passenger’s front air bag ON/OFF

switch is set to the ON position.

If the ABS warning light remains on or

comes on while driving or does not come

on when the ignition switch is turned to

the ON position, this indicates that there

may be a malfunction with the ABS.

If this occurs, have your vehicle checked

by an authorized KIA dealer as soon as

possible. The normal braking system will

still be operational, but without the assis-

tance of the anti-lock brake system.

WARNING

If the both ABS and brake warning

lights are on and stay on, your vehi-

cle’s brake system will not work

normally during sudden braking. In

this case, avoid high speed driving

and abrupt braking. Have your vehi-

cle checked by an authorized KIA

dealer as soon as possible.

CAUTION

If there is a malfunction of the pas-

senger’s front air bag ON/OFF

switch, the passenger’s front air

bag OFF indicator will not illumi-

nate and the passenger’s front air

bag will inflate in frontal impact

crashes even if the passenger’s

front air bag ON/OFF switch is set

to the OFF position.

If this occurs, have an authorized

KIA dealer inspect the passenger’s

front air bag ON/OFF switch and the

SRS air bag system as soon as pos-

sible.

4 31

Features of your vehicle

D150304APA

Seat belt warning chime (if equipped)

Type A

But, if the driver's seat belt is connected

and disconnected twice within 9 seconds

after the belt is fastened, the driver’s seat

belt warning light will not operate.

Seat belt warning

If the driver's seat belt is not fastened

when the ignition switch is turned ON or

if it is unfastened after the ignition switch

is ON, the seat belt warning chime will

sound for approximately 6 seconds. At

this time, if the seat belt is fastened, the

chime will stop immediately.

Seat belt warning light

Type A

If the system does not operate as

described, see an authorized KIA dealer

for assistance.

As a reminder to the driver, the seat belt

warning light will blink for approximately

6 seconds each time you turn the ignition

switch ON regardless of belt fastening.

If the driver’s seat belt is unfastened after

the ignition switch is ON, the seat belt

warning light blinks again for approxi-

mately 6 seconds.

Type B

If the driver's seat belt is not fastened

when the ignition switch is turned ON

and you drive over 9 km/h (6 mph), the

seat belt warning chime will sound for

approximately 100 seconds after the

warning light blinks for approximately 1

minute.

Type B

As a reminder to the driver, the driver’s

seat belt warning light will blink or illumi-

nate for approximately 6 seconds each

time you turn the ignition switch ON

regardless of belt fastening.

If the driver's seat belt is disconnected

after the ignition switch is turned ON and

you drive over 9 km/h (6 mph), the seat

belt warning chime will sound for approx-

imately 100 seconds.

If the driver’s seat belt is not fastened

when the ignition switch is turned ON or

if it is disconnected after the ignition

switch is turned ON, the seat belt warn-

ing light will blink or illuminate until the

belt is fastened.

But, if the driver's seat belt is connected

and disconnected twice within 9 seconds

after the belt is fastened, the seat belt

warning chime will not operate.

4 32

Features of your vehicle

D150305ASA

D150307AUN

CAUTION

Engine oil pressure

warning light

Turn signal indicator

If the oil pressure warning light

stays on while the engine is run-

ning, serious engine damage may

result. The oil pressure warning

light comes on whenever there is

insufficient oil pressure. In normal

operation, it should come on when

the ignition switch is turned on,

then go out when the engine is

started. If the oil pressure warning

light stays on while the engine is

running, there is a serious malfunc-

tion.

The blinking green arrows on the instru-

ment panel shows the direction indicated

by the turn signals. If the arrow comes on

but does not blink or blinks more rapidly

than normal or does not illuminate at all,

it indicates a malfunction in the turn sig-

nal system. It should be checked by an

authorized KIA dealer.

This warning light indicates the engine oil

pressure is low.

If the warning light illuminates while driv-

ing:

1. Drive safely to the side of the road and

stop.

2. With the engine off, check the engine

oil level. If the level is low, add oil as

required.

D150306AUN

If the warning light remains on after

adding oil or if oil is not available, call an

authorized KIA dealer.

High beam indicator

If this happens, stop the car as

soon as it is safe to do so, turn off

the engine and check the oil level. If

the oil level is low, fill the engine oil

to the proper level and start the

engine again. If the light stays on

with the engine running, turn the

engine off immediately. In any

instance where the oil light stays on

when the engine is running, the

engine should be checked by an

authorized KIA dealer before the

car is driven again.

This indicator illuminates when the head-

lights are on and in the high beam posi-

tion or when the turn signal lever is pulled

into the Flash-to-Pass position.

CAUTION

If the engine is not stopped imme-

diately after the engine oil pressure

warning light is illuminated, severe

damage could result.

4 33

Features of your vehicle

D150308ASA

Low brake vacuum pressure warning

(diesel engine only)

3. Do not drive the vehicle if leaks are

found, the warning light remains on or

the brakes do not operate properly.

Have the vehicle towed to any author-

ized KIA dealer for a brake system

inspection and necessary repairs.

Parking brake & brake fluid

warning light

If the warning light remains on, it may

indicate that the brake vacuum pump has

a problem. Therefore you should avoid

high speed driving or sudden stop, and

you should depress the brake pedal

deeper and harder than usual when

braking. Make sure you have the brake

system checked and repaired by an

authorized KIA dealer.

Parking brake warning

This light is illuminated when the parking

brake is applied with the ignition switch in

the START or ON position. The warning

light should go off when the parking

brake is released.

To check bulb operation, check whether

the parking brake and brake fluid warning

light illuminates when the ignition switch

is in the ON position.

Low brake fluid level warning

WARNING

If the warning light remains on, it may

indicate that the brake fluid level in the

reservoir is low.

WARNING

Driving the vehicle with a warning

light on is dangerous. If the brake

warning light remains on, have the

brakes checked and repaired imme-

diately by an authorized KIA dealer.

• Continuous braking while driving

on steep or long downhill may

cause to descend the vacuum

level in brake booster for a time

and turn on the warning light. In

this case, shift down the

transaxle. If the warning light illu-

minate continuously, stop the

vehicle in the safe location and

wait until the warning light goes

off.

If the warning light remains on:

1. Drive carefully to the nearest safe

location and stop your vehicle.

2. With the engine stopped, check the

brake fluid level immediately and add

fluid as required. Then check all brake

components for fluid leaks.

• Driving the vehicle with a warn-

ing light on is dangerous. If the

brake warning light remains on,

have the brakes checked and

repaired immediately by an

authorized KIA dealer.

4 34

Features of your vehicle

D150313AUN

D150315AUN

D150317ASA

Charging system warning

light

Tailgate open warning light

Immobilizer indicator

(if equipped)

This warning light indicates a malfunction

of either the generator or electrical

charging system.

This warning light illuminates when the

tailgate is not closed securely with the

ignition switch in any position.

This light illuminates when the immobiliz-

er key is inserted and turned to the ON

position to start the engine.

If the warning light comes on while the

vehicle is in motion:

1. Drive to the nearest safe location.

At this time, you can start the engine.The

light will go out after the engine starts

running.

D150316AUN

Door ajar warning light

If this light blinks when the ignition switch

is in the ON position before starting the

engine, have the system checked by an

authorized KIA dealer.

2. With the engine off, check the genera-

tor drive belt for looseness or break-

age.

This warning light illuminates when a

door is not closed securely with the igni-

tion switch in any position.

3. If the belt is adjusted properly, a prob-

lem exists somewhere in the electrical

charging system. Have an authorized

KIA dealer correct the problem as

soon as possible.

D150318AUN

Low fuel level warning light

This warning light indicates the fuel tank

is nearly empty. When it comes on, you

should add fuel as soon as possible.

Driving with the fuel level warning light on

or with the fuel level below “E” can cause

the engine to misfire and damage the

catalytic converter.

4 35

Features of your vehicle

D150320AUN-EU

D150323AUN-EE

CAUTION

Malfunction indicator (MIL)

(check engine light)

(if equipped)

ESP indicator (Electronic

Stability Program)

(if equipped)

ESP

Prolonged

Emission

driving

Control

with the

System

Malfunction Indicator Light illumi-

nated may cause damage to the

emission control systems which

could effect drivability and/or fuel

economy.

The ESP indicator will illuminate when

the ignition switch is turned ON, but

should go off after approximately 3 sec-

onds.When the ESP is on, it monitors the

driving conditions and under normal driv-

ing conditions, the ESP light will remain

off. When a slippery or low traction con-

dition is encountered, the ESP will oper-

ate, and the ESP indicator will blink to

indicate the ESP is operating.

This indicator light is part of the Engine

Control System which monitors various

emission control system components. If

this light illuminates while driving, it indi-

cates that a potential malfunction has

been detected somewhere in the emis-

sion control system.

This light will also illuminate when the

ignition switch is turned to the ON posi-

tion, and will go out in a few seconds

after the engine is started. If it illuminates

while driving, or does not illuminate when

the ignition switch is turned to the ON

position, take your vehicle to your near-

est authorized KIA dealer and have the

system checked.

CAUTION

If the Emission Control System

Malfunction Indicator Light illumi-

nates, potential catalytic converter

damage is possible which could

result in loss of engine power. Have

the Engine Control System inspect-

ed as soon as possible by an

authorized KIA dealer.

D150324AUN

ESP

OFF

ESP OFF indicator

(if equipped)

The ESP OFF indicator will illuminate

when the ignition switch is turned ON,

but should go off after approximately 3

seconds. To switch to ESP OFF mode,

press the ESP OFF button. The ESP

OFF indicator will illuminate indicating

the ESP is deactivated. If this indicator

stays on when ESP OFF is not selected,

the ESP may have a malfunction. Take

your car to an authorized KIA dealer and

have the system checked.

Generally, your vehicle will continue to be

drivable, but have the system checked by

an authorized KIA dealer promptly.

4 36

Features of your vehicle

D150334ASA

D150326APA

D150328ASA

Electric power steering

(EPS) system warning light

(if equipped)

Lights on warning chime

(if equipped)

Glow indicator

(Diesel engine)

EPS

The lights on warning chime will sound if

the driver's door is opened and when the

headlight switch is left in the 1st or 2nd

position.

This light comes on when the ignition

switch is turned to the ON position and

then it will go out when the engine starts.

The indicator light illuminates when the

ignition switch is placed at the ON posi-

tion. The engine can be started after the

preheat indicator light goes off. The illu-

minating time varies with the water tem-

perature, air temperature and battery

condition.

This light also comes on if the EPS has a

malfunction. If it comes on while driving,

have your vehicle inspected by an

authorized KIA dealer.

D150327AUN

Key reminder warning chime

(if equipped)

If the driver’s door is opened while the

ignition key is left in the ignition switch

(ACC or LOCK position), the key

reminder warning chime will sound. This

is to prevent you from locking your keys

in the vehicle.The chime sounds until the

key is removed from the ignition switch or

the driver’s door is closed.

✽

NOTICE

Manual transaxle shift

indicator (if equipped)

If the engine does not start within 10

seconds after the preheating is complet-

ed, turn the ignition switch once more to

the LOCK position for 10 seconds, and

then to the ON position, in order to pre-

heat again.

This indicator informs you which gear is

desired while driving to save fuel.

For example

: Indicates that shifting up to the 3rd

gear is desired. (Currently the shift

lever is in the 2nd gear.)

CAUTION

If the glow indicator light continues

to illuminate or blink on and off

after the engine has warmed up or

while driving, check the system by

an authorized KIA dealer as soon as

possible.

: Indicates that shifting down to the

3rd gear is desired. (Currently the

shift lever is in the 4th gear.)

When the system is not working

properly, the Up & Down Arrow

(indicator) will blink (gear is not dis-

played).

4 37

Features of your vehicle

REAR PARKING ASSIST SYS-

TEM (IF EQUIPPED)

D150329AUN

D150330ASA

120

Fuel filter warning light

(Diesel engine)

Overspeed warning

(if equipped)

Overspeed warning light

km/h

This warning light illuminates for 3 sec-

onds after the ignition switch is set to the

ON position and then it will go out. If it

lights up while the engine is running, it

indicates that water has accumulated

inside the fuel filter. If this happens,

remove the water from the fuel filter. For

more information, refer to “Fuel filter” in

section 7.

If you drive with the speed of 120 km/h or

more, the overspeed warning light will

blink. This is to prevent you from over-

speeding.

Rear parking assist system

OSA047060

D170000AEN

CAUTION

The rear parking assist system assists

the driver during backward movement of

the vehicle by chiming if any object is

sensed within a distance of 120 cm (47

in.) behind the vehicle. This system is a

supplemental system and it is not intend-

ed to nor does it replace the need for

extreme care and attention of the driver.

The sensing range and objects

detectable by the back sensors are limit-

ed. Whenever backing-up, pay as much

attention to what is behind you as you

would in a vehicle without a rear parking

assist system.

When the fuel filter warning light is

illuminated, engine power (vehicle

speed & idle speed) may decrease.

If you keep driving with the warning

light on, you can damage your vehi-

cle's engine parts and injection sys-

tem of the Common Rail. If this

occurs, have your vehicle checked

by an authorized KIA dealer as

soon as possible.

4 38

Features of your vehicle

D170200AEN

Operation of the rear parking

assist system

Non-operational conditions of

rear parking assist system

WARNING

The rear parking assist system is a

supplementary function only. The

operation of the rear parking assist

system can be affected by several

factors (including environmental

conditions). It is the responsibility

of the driver to always check the

area behind the vehicle before and

while backing up.

D170101AEN

The rear parking assist system may

not operate properly when:

Operating condition

• This system will activate when backing

up with the ignition switch ON.

1. Moisture is frozen to the sensor. (It will

operate normally when the moisture

has been cleared.)

If the vehicle is moving at a speed over

5 km/h (3 mph), the system may not be

activated correctly.

2. The sensor is covered with foreign

matter, such as snow or water, or the

sensor cover is blocked. (It will operate

normally when the material is removed

or the sensor is no longer blocked.)

• The sensing distance while the rear

parking assist system is in operation is

approximately 120 cm (47 in.).

• When more than two objects are

sensed at the same time, the closest

one will be recognized first.

3. Driving on uneven road surfaces

(unpaved roads, gravel, bumps, gradi-

ent).

4. Objects generating excessive noise

(vehicle horns, loud motorcycle

engines, or truck air brakes) are within

range of the sensor.

D170102AEN

Types of warning sound

• When an object is 120 cm to 81 cm (47

in. to 32 in.) from the rear bumper:

Buzzer beeps intermittently

5. Heavy rain or water spray exists.

6. Wireless transmitters or mobile phones

are within range of the sensor.

• When an object is 80 cm to 41 cm (31

in. to 16 in.) from the rear bumper:

Buzzer beeps more frequently

7. The sensor is covered with snow.

8. Trailer towing.

• When an object is within 40 cm (15 in.)

of the rear bumper:

Buzzer sounds continuously.

4 39

Features of your vehicle

D170300AEN

The detecting range may decrease

when:

✽

NOTICE

Rear parking assist system pre-

cautions

This system can only sense objects with-

in the range and location of the sensors;

It can not detect objects in other areas

where sensors are not installed. Also,

small or slim objects, such as poles or

objects located between sensors may not

be detected by the sensors.

Always visually check behind the vehi-

cle when backing up.

Be sure to inform any drivers of the

vehicle that may be unfamiliar with the

system regarding the systems capabili-

ties and limitations.

1. The sensor is stained with foreign mat-

ter such as snow or water. (The sens-

ing range will return to normal when

removed.)

• The rear parking assist system may

not sound sequentially depending on

the speed and shapes of the objects

detected.

2. Outside air temperature is extremely

hot or cold.

• The rear parking assist system may

malfunction if the vehicle bumper

height or sensor installation has been

modified or damaged. Any non-factory

installed equipment or accessories

may also interfere with the sensor per-

formance.

The following objects may not be rec-

ognized by the sensor:

1. Sharp or slim objects such as ropes,

chains or small poles.

2. Objects which tend to absorb the sen-

sor frequency such as clothes, spongy

material or snow.

• The sensor may not recognize objects

less than 40 cm (15 in.) from the sen-

sor, or it may sense an incorrect dis-

tance. Use caution.

WARNING

3. Undetectable objects smaller than 1 m

(40 in.) and narrower than 14 cm (6 in.)

in diameter.

Pay close attention when the vehi-

cle is driven close to objects on the

road, particularly pedestrians, and

especially children. Be aware that

some objects may not be detected

by the sensors, due to the object’s

distance, size or material, all of

which can limit the effectiveness of

the sensor. Always perform a visu-

al inspection to make sure the vehi-

cle is clear of all obstructions

before moving the vehicle in any

direction.

• When the sensor is frozen or stained

with snow, dirt, or water, the sensor

may be inoperative until the stains are

removed using a soft cloth.

• Do not push, scratch or strike the sen-

sor. Sensor damage could occur.

4 40

Features of your vehicle

LIGHTING

D190100AUN

HAZARD WARNING FLASHER

D170400BUN

Self-diagnosis

Battery saver function

(if equipped)

If you don’t hear an audible warning

sound or if the buzzer sounds intermit-

tently when shifting the gear to the R

(Reverse) position, this may indicate a

malfunction in the rear parking assist

system. If this occurs, have your vehicle

checked by an authorized KIA dealer as

soon as possible.

• The purpose of this feature is to pre-

vent the battery from being dis-

charged. The system automatically

turns off the exterior lights when the

driver removes the ignition key and

opens the driver-side door.

• With this feature, the parking lights will

be turned off automatically if the driver

parks on the side of road at night.

WARNING

OSA047061

If necessary, to keep the lights on

when the ignition key is removed, per-

form the following:

Your new vehicle warranty does not

cover any accidents or damage to

the vehicle or its occupants due to

a rear parking assist system mal-

function. Always drive safely and

cautiously.

D180000AUN

The hazard warning flasher should be

used whenever you find it necessary to

stop the car in a hazardous location.

When you must make such an emer-

gency stop, always pull off the road as far

as possible.

1) Open the driver-side door.

2) Turn the parking lights OFF and ON

again using the light switch on the

steering column.

The hazard warning lights are turned on

by pushing in the hazard switch. This

causes all turn signal lights to blink. The

hazard warning lights will operate even

though the key is not in the ignition

switch.

To turn the hazard warning lights off,

push the switch a second time.

4 41

Features of your vehicle

OSA049090

OSA049091

OSA049092

D190400ASA

D190401AEN

D190402AEN

Headlight position (

)

Parking light position (

)

Lighting control

When the light switch is in the headlight

position (2nd position) the head, tail,

license and instrument panel lights are

ON.

When the light switch is in the parking

light position (1st position), the tail,

license and instrument panel lights are

ON.

The light switch has a Headlight and a

Parking light position.

To operate the lights, turn the knob at the

end of the control lever to one of the fol-

lowing positions:

✽

NOTICE

The ignition switch must be in the ON

position to turn on the headlights.

(1) OFF position

(2) Parking light position

(3) Headlight position

4 42

Features of your vehicle

OSA049093

OSA049094

OSA049095

D190500AUN

D190600AUN

To flash the headlights, pull the lever

towards you. It will return to the normal

(low beam) position when released. The

headlight switch does not need to be on

to use this flashing feature.

High beam operation

Turn signals and lane change sig-

nals

To turn on the high beam headlights,

push the lever away from you. Pull it back

for low beams.

The ignition switch must be on for the

turn signals to function. To turn on the

turn signals, move the lever up or down

(A). Green arrow indicators on the instru-

ment panel indicate which turn signal is

operating. They will self-cancel after a

turn is completed. If the indicator contin-

ues to flash after a turn, manually return

the lever to the OFF position.

The high beam indicator will light when

the headlight high beams are switched

on.

To prevent the battery from being dis-

charged, do not leave the lights on for a

prolonged time while the engine is not

running.

4 43

Features of your vehicle

To signal a lane change, move the turn

signal lever slightly and hold it in position

(B). The lever will return to the OFF posi-

tion when released.

If an indicator stays on and does not

flash or if it flashes abnormally, one of the

turn signal bulbs may be burned out and

will require replacement.

✽

NOTICE

If an indicator flash is abnormally quick

or slow, a bulb may be burned out or

have a poor electrical connection in the

circuit.

OSA047080

OSA047081

D190700ASA

D190800ASA

Front fog light (if equipped)

Rear fog light (if equipped)

Fog lights are used to provide improved

visibility when visibility is poor due to fog,

rain or snow, etc. The fog lights will turn

on when the fog light button is pressed

after the ignition switch is in the ON posi-

tion and the parklight is turned on.

To turn the rear fog lights on, turn the

headlight switch to the headlight on posi-

tion and press the rear fog light button

(the light will illuminate).

Also, the rear fog lights turn on when the

rear fog button is pressed after the front

fog button is turned ON and the headlight

switch to the parklight position. (if

equipped)

To turn off the fog lights, press the button

again.

To turn the rear fog lights off, press the

rear fog light button again or turn the

headlight switch to the OFF position.

CAUTION

When in operation, the fog lights

consume large amounts of vehicle

electrical power. Only use the fog

lights when visibility is poor.

4 44

Features of your vehicle

Listed below are the examples of proper

switch settings. For loading conditions

other than those listed below, adjust the

switch position so that the beam level

may be the nearest as the condition

obtained according to the list.

✽

NOTICE

When you turn off the rear fog light by

turning the headlight switch to the off

position, be sure to turn the rear fog

light button off too by pressing the but-

ton again. The chime may sound when

you open the door if the rear fog light

button is on, even though the rear fog

light is off.

Switch setting:

Loading on

Position

Rear luggage

D190900AUN

Front seats Rear seats

room

Daytime running light

(if equipped)

OSA047082

1 driver

-

0

D191001ASA

Daytime Running Lights (DRL) can make

it easier for others to see the front of your

vehicle during the day. DRL can be help-

ful in many different driving conditions,

and it is especially helpful after dawn and

before sunset.

2 persons

-

Headlight leveling device

(if equipped)

1

2

3

2 persons 3 persons

-

55 kg

320 kg

To adjust the headlight beam level

according to the number of the passen-

gers and the loading weight in the lug-

gage area, turn the beam leveling switch.

1 driver

-

The DRL system will make the head-

lights turn OFF when:

The higher the number of the switch

position, the lower the headlight beam

level. Always keep the headlight beam at

the proper leveling position, or headlights

may dazzle other road users.

1. The parklight switch is ON.

2. Engine stops.

4 45

Features of your vehicle

WIPERS AND WASHERS

Windshield wiper/washer

A : Wiper speed control

Rear window wiper/washer

(if equipped)

· MIST ( ) – Single wipe

· OFF (O) – Off

Type A

· INT (---) – Intermittent wipe

· LO (1) – Low wiper speed

· HI (2) – High wiper speed

B : Intermittent wipe time adjustment

C : Wash with brief wipes

Type B

D : Rear wiper/washer control

Type B

·

– Wash with brief wipes

· ON ( ) – Continuous wipe

· OFF (O) – Off

OMC048901/OMC048901N/OSA049904L/OSA049904

4 46

Features of your vehicle

Type A

MIST (

) : For a single wiping cycle,

push the lever upward and

release it with the lever in

the OFF (O) position. The

wipers will operate contin-

uously if the lever is

pushed upward and held.

1

OFF (O) : Wiper is not in operation

INT (---) : Wiper operates intermittently

at the same wiping intervals.

Use this mode in light rain or

mist. To vary the speed setting,

turn the speed control knob(1).

OMC048902

OMC048905

Type B

LO (1) : Normal wiper speed

HI (2) : Fast wiper speed

1

✽

NOTICE

If there is heavy accumulation of snow

or ice on the windshield, defrost the

windshield for about 10 minutes, or

until the snow and/or ice is removed

before using the windshield wipers to

ensure proper operation.

OMC048902N

OMC048905N

D200100BSA

D200102BSA

Variable intermittent wipers

Windshield wipers

Set the lever to the INT (---) position and

choose the desired wiper interval by turn-

ing the ring(1).

Operates as follows when the ignition

switch is turned ON.

4 47

Features of your vehicle

Type A

✽

NOTICE

• To prevent possible damage to the

wipers or windshield, do not operate

the wipers when the windshield is dry.

• To prevent damage to the wiper

blades, do not use gasoline, kerosene,

paint thinner, or other solvents on or

near them.

• To prevent damage to the wiper arms

and other components, do not attempt

to move the wipers manually.

OMC048904

OMC048903

Type B

OMC048904N

OMC048903N

D200200BSA

D200103BSA

Windshield washers

One - touch wiper

In the OFF (O) position, pull the lever

gently toward you to spray washer fluid

on the windshield and to run the wipers

1-3 cycles.

For a single wiping cycle, push the lever

upward and release it with the lever in the

OFF (O) position.

The wipers will operate continuously if

the lever is pushed upward and held.

Use this function when the windshield is

dirty.

4 48

Features of your vehicle

Type A

The spray and wiper operation will con-

tinue until you release the lever.

WARNING

If the washer does not work, check the

washer fluid level. If the fluid level is not

sufficient, you will need to add appropri-

ate non-abrasive windshield washer fluid

to the washer reservoir.

Do not use the washer in freezing

temperatures without first warming

the windshield with the defrosters;

the washer solution could freeze on

the windshield and obscure your

vision.

The reservoir filler neck is located in the

front of the engine compartment on the

passenger side.

CAUTION

OSA049905L

Type B

• To prevent possible damage to

the wipers or windshield, do not

operate the wipers when the

windshield is dry.

CAUTION

To prevent possible damage to the

washer pump, do not operate the

washer when the fluid reservoir is

empty.

• To prevent damage to the wiper

blades, do not use gasoline,

kerosene, paint thinner, or other

solvents on or near them.

• To prevent damage to the wiper

arms and other components, do

not attempt to move the wipers

manually.

OSA049905

D200300BPA

Rear window wiper and washer

switch (if equipped)

The rear window wiper and washer

switch is located at the end of the wiper

and washer switch lever. Turn the switch

to desired position to operate the rear

wiper and washer.

4 49

Features of your vehicle

INTERIOR LIGHT

D210000AEN

- Spraying washer fluid and wiping

ON (

) - Normal wiper operation

CAUTION

Do not use the interior lights for

extended periods when the engine

is not running.

OFF (O) - Wiper is not in operation

It may cause battery discharge.

OSA047096

D210300APA

Luggage lamp (if equipped)

The light comes on when the tailgate is

opened.

OSA047088

D210200ASA

Room lamp

(1) OFF - The light stays off even when a

door is open.

(2) DOOR - The light turns on or off

when a door is opened or

closed.

(3) ON - The light turns on and stays on

even when the doors are all

closed.

4 50

Features of your vehicle

DEFROSTER

D220000AUN

CAUTION

To prevent damage to the conduc-

tors bonded to the inside surface of

the rear window, never use sharp

instruments or window cleaners

containing abrasives to clean the

window.

✽

NOTICE

OSA047089

If you want to defrost and defog the

front windshield, refer to “Windshield

defrosting and defogging” in this sec-

tion.

D220100ASA

Rear window defroster

The defroster heats the window to

remove frost, fog and thin ice from the

rear window, while the engine is running.

D220101AUN

Outside mirror defroster

(if equipped)

To activate the rear window defroster,

press the rear window defroster button.

The indicator on the rear window

defroster button illuminates when the

defroster is ON.

If your vehicle is equipped with outside

mirror defrosters, they will operate at the

same time when you turn on the rear

window defroster.

If there is heavy accumulation of snow on

the rear window, brush it off before oper-

ating the rear defroster.

To turn off the defroster, press the rear

window defroster button again.

4 51

Features of your vehicle

MANUAL CLIMATE CONTROL SYSTEM (IF EQUIPPED)

1. Fan speed control knob

2. Mode selection knob

4. Air intake control lever

5. Air conditioning button*

* : if equipped

3. Temperature control knob

OSA047100

D230000ASA

4 52

Features of your vehicle

D230100AEN

Heating and air conditioning

1. Start the engine.

2. Set the mode to the desired position.

To improve the effectiveness of heat-

ing and cooling;

- Heating:

- Cooling:

3. Set the temperature control to the

desired position.

4. Set the air intake control to the outside

(fresh) air position.

5. Set the fan speed control to the

desired speed.

6. If air conditioning is desired, turn the

air conditioning system (if equipped)

on.

OSA040104

4 53

Features of your vehicle

Bi-Level (B, D, C)

Air flow is directed towards the face and

the floor.

Floor-Level (C, A, D)

Most of the air flow is directed to the

floor, with a small amount of the air being

directed to the windshield and side win-

dow defrosters.

OSA047103

OSA040105

D230101APA

Instrument panel vents

The outlet vents can be opened or closed

separately using the thumbwheel.

Mode selection

The mode selection knob controls the

direction of the air flow through the venti-

lation system.

Floor/Defrost-Level (A, C, D)

Also, you can adjust the direction of air

delivery from these vents using the vent

control lever as shown.

Most of the air flow is directed to the floor

and the windshield with a small amount

directed to the side window defrosters.

Air can be directed to the floor, dash-

board outlets, or windshield. Five sym-

bols are used to represent Face, Bi-

Level, Floor, Floor-Defrost and Defrost

air position.

Defrost-Level (A, D)

Most of the air flow is directed to the

windshield with a small amount of air

directed to the side window defrosters.

Face-Level (B, D)

Air flow is directed toward the upper body

and face. Additionally, each outlet can be

controlled to direct the air discharged

from the outlet.

4 54

Features of your vehicle

OSA047102

OSA047106

OSA047123

D230102AUN

D230103ASA

Recirculated air position

Temperature control

Air intake control

This is used to select the outside (fresh)

air position or recirculated air position.

With the recirculated air position select-

ed, air from the passenger compartment

will be drawn through the heating system

and is heated or cooled according to the

function selected.

The temperature control knob allows you

to control the temperature of the air flow

from the ventilation system. To change

the air temperature in the passenger

compartment, turn the knob to the right

position for warm air or left position for

cooler air.

To change the air intake control position,

move the control lever.

4 55

Features of your vehicle

WARNING

• Continue using the climate con-

trol system in the recirculated air

position may allow humidity to

increase inside the vehicle which

may fog the glass and obscure

visibility.

• Do not sleep in a vehicle with the

air conditioning or heating sys-

tem on. It may cause serious

harm or death due to a drop in the

oxygen level and/or body temper-

ature.

OSA047124

OSA047101

D230104ASA

Outside (fresh) air position

Fan speed control

The ignition switch must be in the ON

position for fan operation.

With the outside (fresh) air position

selected, air enters the vehicle from out-

side and is heated or cooled according to

the function selected.

• Continue using the climate con-

trol system in the recirculated air

position can cause drowsiness or

sleepiness, and loss of vehicle

control. Set the air intake control

to the outside (fresh) air position

as much as possible while driv-

ing.

The fan speed control knob allows you to

control the fan speed of the air flow from

the ventilation system. To change the fan

speed, turn the knob to the right for high-

er speed or left for lower speed.

✽

NOTICE

Prolonged operation of the heater in the

recirculated air position (without air

conditioning selected) may cause fog-

ging of the windshield and side windows

and the air within the passenger com-

partment may become stale.

In addition, prolonged use of the air

conditioning with the recirculated air

position selected will result in excessive-

ly dry air in the passenger compart-

ment.

0 - Fan off

1 - Low speed

2 - Medium speed

3 - High speed

4 - Maximum speed

4 56

Features of your vehicle

Operation Tips

System operation

• To keep dust or unpleasant fumes from

entering the car through the ventilation

system, temporarily set the air intake

control to the recirculated air position.

Be sure to return the control to the

fresh air position when the irritation

has passed to keep fresh air in the

vehicle. This will help keep the driver

alert and comfortable.

D230501AUN

Ventilation

1. Set the mode to the

position.

2. Set the air intake control to the outside

(fresh) air position.

3. Set the temperature control to the

desired position.

4. Set the fan speed control to the

desired speed.

• Air for the heating/cooling system is

drawn in through the grilles just ahead

of the windshield. Care should be

taken that these are not blocked by

leaves, snow, ice or other obstructions.

OSA047107

D230502AEN

D230105AUN

Heating

1. Set the mode to the

Air conditioning (if equipped)

position.

• To prevent interior fog on the wind-

shield, set the air intake control to the

fresh air position and fan speed to the

desired position, turn on the air condi-

tioning system, and adjust the temper-

ature control to desired temperature.

Push the A/C button to turn the air condi-

tioning system on (indicator light will illu-

minate). Push the button again to turn the

air conditioning system off.

2. Set the air intake control to the outside

(fresh) air position.

3. Set the temperature control to the

desired position.

4. Set the fan speed control to the

desired speed.

5. If dehumidified heating is desired, turn

the air conditioning system (if

equipped) on.

• If the windshield fogs up, set the mode

to the

or

position.

4 57

Features of your vehicle

D230503ASA

• During air conditioning system opera-

tion, you may occasionally notice a

slight change in engine speed as the

air conditioning compressor cycles.

This is a normal system operation

characteristic.

✽

NOTICE

Air conditioning (if equipped)

• When using the air conditioning sys-

tem, monitor the temperature gauge

closely while driving up hills or in

heavy traffic when outside tempera-

tures are high. Air conditioning sys-

tem operation may cause engine over-

heating. Continue to use the blower

fan but turn the air conditioning sys-

tem off if the temperature gauge indi-

cates engine overheating.

• When opening the windows in humid

weather air conditioning may create

water droplets inside the vehicle.

Since excessive water droplets may

cause damage to electrical equipment,

air conditioning should only be run

with the windows closed.

All KIA Air Conditioning Systems are

filled with environmentally friendly

R-134a refrigerant which does not dam-

age the ozone layer.

• Use the air conditioning system every

month only for a few minutes to ensure

maximum system performance.

1. Start the engine. Push the air condi-

tioning button.

2. Set the mode to the

position.

• When using the air conditioning sys-

tem, you may notice clear water drip-

ping (or even puddling) on the ground

under the passenger side of the vehi-

cle. This is a normal system operation

characteristic.

3. Set the air intake control to the outside

air or recirculated air position.

4. Adjust the fan speed control and tem-

perature control to maintain maximum

comfort.

• When maximum cooling is desired, set

the temperature control to the extreme

left position, set the air intake control to

the recirculated air position, then set

the fan speed control to the highest

speed.

• Operating the air conditioning system

in the recirculated air position provides

maximum cooling, however, continual

operation in this mode may cause the

air inside the vehicle to become stale.

Air conditioning system operation tips

• During cooling operation, you may

occasionally notice a misty air flow

because of rapid cooling and humid air

intake. This is a normal system opera-

tion characteristics.

• If the vehicle has been parked in direct

sunlight during hot weather, open the

windows for a short time to let the hot

air inside the vehicle escape.

• To help reduce moisture inside of the

windows on rainy or humid days,

decrease the humidity inside the vehi-

cle by operating the air conditioning

system.

4 58

Features of your vehicle

D230400AUN

✽

NOTICE

• Replace the filter according to the

Maintenance Schedule.

If the vehicle is being driven in severe

conditions such as dusty, rough roads,

more frequent climate control air fil-

ter inspections and changes are

required.

Checking the amount of air con-

ditioner refrigerant and compres-

sor lubricant

Outside air

Recirculated

air

When the amount of refrigerant is low,

the performance of the air conditioning is

reduced. Overfilling also has a negative

impact on the air conditioning system.

• When the air flow rate suddenly

decreases, the system should be

checked by an authorized KIA dealer.

Therefore, if abnormal operation is

found, have the system inspected by an

authorized KIA dealer.

Blower

Heater core

Climate control

air filter

Evaporator

core

1LDA5047

✽

NOTICE

Climate control air filter

(if equipped)

It is important that the correct type and

amount of oil and refrigerant is used.

Otherwise, damage to the compressor

and abnormal system operation may

occur.

The climate control air filter installed

behind the glove box filters the dust or

other pollutants that come into the vehi-

cle from the outside through the heating

and air conditioning system. If dust or

other pollutants accumulate in the filter

over a period of time, the air flow from the

air vents may decrease, resulting in

moisture accumulation on the inside of

the windshield even when the outside

(fresh) air position is selected. If this hap-

pens, have the climate control air filter

replaced by an authorized KIA dealer.

WARNING

The air conditioning system should

be serviced by an authorized KIA

dealer. Improper service may cause

serious injury to the person per-

forming the service.

4 59

Features of your vehicle

AUTOMATIC CLIMATE CONTROL SYSTEM (IF EQUIPPED)

1. AUTO (automatic control) button

2. Temperature control knob

3. Climate control display

4. Fan speed control knob

5. OFF button

7. Mode selection button

8. Air conditioning button

9. Air intake control button

6. Front windshield defrost button

OSA040108

D240000ASA

4 60

Features of your vehicle

2. Turn the TEMP knob to set the desired

temperature.

If the temperature is set to the lowest

setting (Lo), the air conditioning sys-

tem will operate continuously.

3. To turn the automatic operation off,

press any button or turn any knob

except the temperature control knob. If

you press the mode selection button,

air conditioning button, defrost button

or air intake control button, or turn the

fan speed knob, the selected function

will be controlled manually while other

functions operate automatically.

OSA047109

OSA047110

D240100BUN

✽

NOTICE

Automatic heating and air condi-

tioning

The automatic climate control system is

controlled by simply setting the desired

temperature.

Never place anything over the sensor

located on the instrument panel to

ensure better control of the heating and

cooling system.

The Full Automatic Temperature Control

(FATC) system automatically controls the

heating and cooling system as follows;

1. Push the AUTO button. It is indicated

by AUTO on the display. The modes,

fan speeds, air intake and air-condi-

tioning will be controlled automatically

by temperature setting.

4 61

Features of your vehicle

D240200AUN

Manual heating and air condition-

ing

Face-Level (B, D)

Air flow is directed toward the upper body

and face. Additionally, each outlet can be

controlled to direct the air discharged

from the outlet.

The heating and cooling system can be

controlled manually by pushing buttons

other than the AUTO button. In this case,

the system works sequentially according

to the order of buttons selected.

When pressing any button (or turning

any knob) except AUTO button while

automatic operation, the functions not

selected will be controlled automatically.

Bi-Level (B, D, C)

Air flow is directed towards the face and

the floor.

OSA040114

1. Start the engine.

2. Set the mode to the desired position.

D240201AUN

Mode selection

3. Set the temperature control to the

desired position.

The mode selection button controls the

direction of the air flow through the venti-

lation system.

4. Set the air intake control to the outside

(fresh) air position.

The air flow outlet port is converted as

follows:

5. Set the fan speed control to the

desired speed.

6. If air conditioning is desired, turn the

air conditioning system on.

Press the AUTO button in order to con-

vert to full automatic control of the sys-

tem.

Refer to the illustration in the “Manual cli-

mate control system”.

4 62

Features of your vehicle

Floor-Level (C, A, D)

Most of the air flow is directed to the

floor, with a small amount of the air being

directed to the windshield and side win-

dow defrosters.

Floor/Defrost-Level (A, C, D)

Most of the air flow is directed to the floor

and the windshield with a small amount

directed to the side window defrosters.

OSA040115

OSA040105

Defrost-Level (A, D)

Instrument panel vents

The outlet vents can be opened or closed

separately using the thumbwheel.

Most of the air flow is directed to the

windshield with a small amount of air

directed to the side window defrosters.

Also, you can adjust the direction of air

delivery from these vents using the vent

control lever as shown.

4 63

Features of your vehicle

Temperature conversion

If the battery has been discharged or dis-

connected, the temperature mode dis-

play will reset to Centigrade.

This is a normal condition.You can switch

the

Centigrade to Fahrenheit as follows;

temperature

mode

between

While depressing the AUTO button,

depress the OFF button for 3 seconds or

more. The display will change from

Centigrade to Fahrenheit, or from

Fahrenheit to Centigrade.

OSA047111

OSA047125

D240202AUN

D240207AUN

Temperature control

Outside thermometer

The temperature will increase to the

maximum (HI) by turning the knob to the

right extremely.

The current outside temperature is dis-

played in 1°C (1°F) increments. The tem-

perature range is between -40°C ~ 60°C

(-40°F~140°F).

The temperature will decrease to the

minimum (Lo) by turning the knob to the

left extremely.

When turning the knob, the temperature

will increase or decrease by 0.5°C/1°F.

When set to the lowest temperature set-

ting, the air conditioning will operate con-

tinuously.

4 64

Features of your vehicle

Recirculated air position

The recirculated air position

Outside (fresh) air position Recirculated air position

✽

NOTICE

Prolonged operation of the heater in the

recirculated air position (without air

conditioning selected) may cause fog-

ging of the windshield and side windows

and the air within the passenger com-

partment may become stale.

In addition, prolonged use of the air con-

ditioning with the recirculated air posi-

tion selected will result in excessively dry

air in the passenger compartment.

indicator in the climate con-

trol display illuminates when

the recirculated air position

is selected.

With the recirculated air posi-

tion selected, air from the

passenger compartment will

be drawn through the heat-

ing system and heated or

cooled according to the func-

tion selected.

OSA040113

WARNING

D240203ASA

• Continue using the climate con-

trol system in the recirculated air

position may allow humidity to

increase inside the vehicle which

may fog the glass and obscure vis-

ibility.

Air intake control

This is used to select outside (fresh) air

position or recirculated air position.

Outside (fresh) air position

The outside (fresh) air posi-

tion indicator in the climate

control display illuminates

when the outside (fresh) air

position is selected.

To change the air intake control position,

push the control button.

• Do not sleep in a vehicle with air

conditioning or heating system on.

It may cause serious harm or death

due to a drop in the oxygen level

and/or body temperature.

With the outside (fresh) air

position selected, air enters

the vehicle from outside and

is heated or cooled accord-

ing to the function selected.

• Continue using the climate con-

trol system in the reciruclated air

position can cause drowsiness or

sleepiness, and loss of vehicle

control. Set the air intake control to

the outside (fresh) air position as

much as possible while driving.

4 65

Features of your vehicle

OSA047112

OSA040116

OSA047117

D240205AUN

D240206ASA

D240208AUN

Fan speed control

Air conditioning

OFF mode

The fan speed can be set to the desired

speed by turning the fan speed control

knob.

Push the OFF button to turn off the air cli-

mate control system. However, you can

still operate the mode and air intake but-

tons as long as the ignition switch is in

the ON position.

Push the A/C button to turn the air condi-

tioning system on.

Push the button again to turn the air con-

ditioning system off.

The higher the fan speed is, the more air

is delivered.

Pressing the OFF button turns off the

fan.

4 66

Features of your vehicle

WINDSHIELD DEFROSTING AND DEFOGGING

D250000AEN

• For maximum defrosting, set the tem-

perature control to the extreme

right/hot position and the fan speed

control to the highest speed.

WARNING - Windshield

heating

• If warm air to the floor is desired while

defrosting or defogging, set the mode

to the floor-defrost position.

Do not use the

or

position

during cooling operation in

extremely humid weather. The dif-

ference between the temperature of

the outside air and that of the wind-

shield could cause the outer sur-

face of the windshield to fog up,

causing loss of visibility. In this

case, set the mode selection knob

• Before driving, clear all snow and ice

from the windshield, rear window, out-

side rear view mirrors, and all side win-

dows.

• Clear all snow and ice from the hood

and air inlet in the cowl grill to improve

heater and defroster efficiency and to

reduce the probability of fogging up the

inside of the windshield.

OSA047118

or button to the

position and

Manual climate control system

fan speed control knob or button to

the lower speed.

D250101ASA

To defog inside windshield

1. Select any fan speed except “0”.

2. Select desired temperature.

3. Select the

or

position.

4. Turn on the air-conditioning system.

5. Select the outside (fresh) air mode.

4 67

Features of your vehicle

OSA047119

OSA040120

OSA040121

D250102ASA

D250202AUN

Automatic climate control system

To defrost outside windshield

1. Set the fan speed to the “3” or “4” posi-

tion.

To defrost outside windshield

1. Set the fan speed to the highest

(extreme right) position.

D250201ASA

To defog inside windshield

1. Set the fan speed to the desired posi-

tion.

2. Select desired temperature.

2. Set the temperature to the extreme hot

position.

2. Set the temperature to the extreme hot

(HI) position.

3. Select the

position.

3. Press the defrost button (

).

3. Select the

or

position.

4. Turn on the air-conditioning system.

5. Select the outside (fresh) air mode.

4. The air conditioning will be turned on

according to the detected ambient

temperature and outside (fresh) air

position will be selected automatically.

4. The air conditioning will be turned on

according to the detected ambient tem-

perature and outside (fresh) air posi-

tion will be selected automatically.

If the position is selected, lower fan

speed is controlled to higher fan speed.

If the air conditioning and outside (fresh)

air position are not selected automatical-

ly, adjust the corresponding button man-

ually. If the

position is selected,

lower fan speed is automatically con-

trolled to a more higher fan speed.

4 68

Features of your vehicle

D250300AUN

Defogging logic

To reduce the possibility of fogging up

the inside of the windshield, the air intake

or air conditioning are controlled auto-

matically according to certain conditions

such as

or

position.To cancel or

return the defogging logic, do the follow-

ing.

OSA040122

D250302AUN

Automatic climate control system

1. Turn the ignition switch to the ON posi-

tion.

2. Select the defrost position pressing

defrost button (

).

3. While holding the air conditioning but-

ton (A/C) pressed, press the air intake

control button (

within 3 seconds.

) at least 5 times

The A/C display blinks 3 times with 0.5

second of interval. It indicates that the

defogging logic is canceled or returned to

the programmed status.

If the battery has been discharged or dis-

connected, it resets to the defog logic

status.

4 69

Features of your vehicle

STORAGE COMPARTMENT

D270000AHM

These compartments can be used to

store small items.

WARNING - Flammable

materials

Do not store cigarette lighters,

propane cylinders, or other flamma-

ble/explosive materials in the vehi-

cle. These items may catch fire

and/or explode if the vehicle is

exposed to hot temperatures for

extended periods.

CAUTION

• To avoid possible theft, do not

leave valuables in the storage

compartment.

• Always keep the storage com-

partment covers closed while

driving. Do not attempt to place

so many items in the storage

compartment that the storage

compartment cover cannot close

securely.

OSA047135

D270200AUN

Glove box

To open the glove box, pull the handle

and the glove box will automatically

open. Close the glove box after use.

WARNING

To reduce the risk of injury in an

accident or sudden stop, always

keep the glove box door closed

while driving.

4 70

Features of your vehicle

WARNING

• Do not keep objects except sun-

glasses inside the sunglass hold-

er. Such objects can be thrown

from the holder in the event of a

sudden stop or an accident, pos-

sibly injuring the passengers in

the vehicle.

• Do not open the sunglass holder

while the vehicle is moving. The

rear view mirror of the vehicle

can be blocked by an open sun-

glass holder.

OSA0470221

D270300ASA

Sunglass holder (if equipped)

To open the sunglass holder, pull the

cover. Place your sunglasses in the com-

partment door with the lenses facing out.

The cover will close when released.

4 71

Features of your vehicle

INTERIOR FEATURES

WARNING

• Do not hold the lighter in after it

is already heated because it will

overheat.

• If the lighter does not pop out

within 30 seconds, remove it to

prevent overheating.

CAUTION

Only a genuine KIA lighter should

be used in the cigarette lighter

socket. The use of plug-in acces-

sories (shavers, hand-held vacu-

ums, and coffee pots, etc.) may

damage the socket or cause electri-

cal failure.

OSA047141

OSA040142

D280100AUN

D280200AUN

Ashtray (if equipped)

Cigarette lighter (if equipped)

For the cigarette lighter to work, the igni-

tion switch must be in the ACC position

or the ON position.

WARNING - Ashtray use

• Do not use the vehicle’s ashtrays

as waste receptacles.

To use the cigarette lighter, push it all the

way into its socket. When the element

has heated, the lighter will pop out to the

“ready” position.

• Putting lit cigarettes or matches

in an ashtray with other com-

bustible materials may cause a

fire.

If it is necessary to replace the cigarette

lighter, use only a genuine KIA replace-

ment or its approved equivalent.

D280201ASA

To use the ashtray, open the cover.

To remove the ashtray to empty or clean,

pull it up and out.

4 72

Features of your vehicle

D280300APA

Front

Cup holder

WARNING - Hot liquids

• Do not place uncovered cups

with hot liquid in the cup holder

while the vehicle is in motion. If

the hot liquid spills, you can burn

yourself. Such a burn to the driv-

er could lead to loss of control of

the vehicle.

OSA040130

Rear

• To reduce the risk of personal

injury in the event of sudden stop

or collision, do not place uncov-

ered or unsecured bottles, glass-

es, cans, etc., in the cup holder

while the vehicle is in motion.

OSA047136

D280400ASA

Sunvisor

Use the sunvisor to shield direct light

through the front or side windows.

To use a sunvisor, pull it downward.

To use a sunvisor for the side window,

pull it downward, unsnap it from the

bracket (1) and swing it to the side (2).

OSA047131

D280301AUN

Front/Rear (if equipped)

Cups or small beverage cans may be

placed in the cup holders.

4 73

Features of your vehicle

Whenever the battery terminals or relat-

ed fuses are disconnected, you must

reset the time.

Type A

When the ignition switch is in the ACC or

ON position, the clock buttons operate as

follows:

D280601ASA

Hour:

Turn the knob to the left (H), will advance

the time displayed by one hour.

OSA047132

Type B

OSA047140

D280602ASA

D281400AFD

Minute:

Aux, USB and iPod port

(if equipped)

Turn the knob to the right (M), will

advance the time displayed by one

minute.

If your vehicle has an aux and/or

USB(universal serial bus) port or iPod

port, you can use an aux port to connect

audio devices and an USB port to plug in

an USB and also an iPod port to plug in

an iPod.

D280603ASA

Reset

To clear away the minutes, press the

knob for more than 1 second.

OSA049132

D280600ASA

Then the clock will be set precisely to the

hour.

✽

NOTICE

Digital clock (if equipped)

When using a portable audio device

connected to the power outlet, noise may

occur during playback. If this happens,

use the power source of the portable

audio device.

WARNING

For example, if the knob is pressed while

the time is between 9:01 and 9:29, the

display will reset to 9:00.

Do not adjust the clock while driv-

ing. You may lose your steering

control and cause severe personal

injury or accidents.

9:01 ~ 9:29 display changed to 9:00

9:30 ~ 9:59 display changed to 10:00

❈ iPod is a trademark of Apple Inc.

4 74

Features of your vehicle

Type A

CAUTION

• Use the power outlet only when

the engine is running and remove

the accessory plug after use.

Using the accessory plug for pro-

longed periods of time with the

engine off could cause battery

discharge.

• Only use 12V electric accessories

which are less than 10A in elec-

tric capacity.

OSA047133

Type B

OSA047144K

• Adjust the air-conditioner or

heater to the lowest operating

level when using the power out-

let.

D280500AUN

Power outlet (if equipped)

The power outlet is designed to provide

power for mobile telephones or other

devices designed to operate with vehicle

electrical systems. The devices should

draw less than 10 amps with the engine

running.

• Close the cover when not in use.

• Some electronic devices can

cause electronic interference

when plugged into a vehicle’s

power outlet. These devices may

cause excessive audio static and

malfunctions in other electronic

systems or devices used in your

vehicle.

OSA047133K

D280800BEN

Clothes hanger (if equipped)

CAUTION

Do not hang heavy clothes, since

those may damage the hook.

4 75

Features of your vehicle

CAUTION

Do not put fragile, bulky or exces-

sive quantity of items into the lug-

gage net. They could be damaged.

WARNING

To avoid eye injury, DO NOT over-

stretch the netting.

ALWAYS keep your face and body

out of the luggage net’s recoil path.

1SAA2162

D281000ASA

DO NOT use the luggage net when

the strap has visible signs of wear

or damage.

Luggage net (if equipped)

To keep items from shifting in the lug-

gage room, you can use the two hooks

located in the luggage room to attach the

cargo net.

4 76

Features of your vehicle

AUDIO SYSTEM

Type A

CAUTION

• Before entering a place with a low

height clearance, be sure that the

antenna is fully folded down (type

A only) or removed.

• Be sure to remove the antenna

before washing the car in an auto-

matic car wash or it may be dam-

aged.

• When reinstalling your antenna,

it is important that it is fully tight-

ened and adjusted to the upright

position to ensure proper recep-

tion.

OSA0470220

Type B

OPB049135

Antenna

Roof antenna

Your vehicle uses a roof antenna to

receive both AM and FM broadcast sig-

nals. This antenna can be adjusted up

and down (type A only) or removed from

the vehicle. To remove the antenna, turn

it counterclockwise. To install the anten-

na, turn it clockwise.

4 77

Features of your vehicle

FM reception

AM(MW, LW) reception

FM radio station

¢

JBM001

JBM002

JBM003

D300800AUN

AM(MW, LW) broadcasts can be

received at greater distances than FM

broadcasts. This is because AM(MW,

LW) radio waves are transmitted at low

frequencies. These long, low frequency

radio waves can follow the curvature of

the earth rather than travelling straight

out into the atmosphere. In addition, they

curve around obstructions so that they

can provide better signal coverage.

FM broadcasts are transmitted at high

frequencies and do not bend to follow the

earth's surface. Because of this, FM

broadcasts generally begin to fade at

short distances from the station. Also,

FM signals are easily affected by build-

ings, mountains, or other obstructions.

These can result in certain listening con-

ditions which might lead you to believe a

problem exists with your radio. The fol-

lowing conditions are normal and do not

indicate radio trouble:

How car audio works

AM(MW, LW) and FM radio signals are

broadcast from transmitter towers locat-

ed around your city. They are intercept-

ed by the radio antenna on your car. This

signal is then received by the radio and

sent to your car speakers.

When a strong radio signal has reached

your vehicle, the precise engineering of

your audio system ensures the best pos-

sible quality reproduction. However, in

some cases the signal coming to your

vehicle may not be strong and clear. This

can be due to factors such as the dis-

tance from the radio station, closeness of

other strong radio stations or the pres-

ence of buildings, bridges or other large

obstructions in the area.

4 78

Features of your vehicle

Using a cellular phone or a two-way

radio

When a cellular phone is used inside the

vehicle, noise may be produced from the

audio equipment. This does not mean

that something is wrong with the audio

equipment. In such a case, use the cellu-

lar phone at a place as far as possible

from the audio equipment.

¢

CAUTION

JBM004

JBM005

When using a communication sys-

tem such a cellular phone or a radio

set inside the vehicle, a separate

external antenna must be fitted.

When a cellular phone or a radio set

is used with an internal antenna

alone, it may interfere with the vehi-

cle's electrical system and adverse-

ly affect safe operation of the vehi-

cle.

• Fading - As your car moves away from

the radio station, the signal will weaken

and sound will begin to fade. When this

occurs, we suggest that you select

another stronger station.

• Station Swapping - As a FM signal

weakens, another more powerful sig-

nal near the same frequency may

begin to play. This is because your

radio is designed to lock onto the clear-

est signal. If this occurs, select anoth-

er station with a stronger signal.

• Flutter/Static - Weak FM signals or

large obstructions between the trans-

mitter and your radio can disturb the

signal causing static or fluttering nois-

es to occur. Reducing the treble level

may lessen this effect until the distur-

bance clears.

• Multi-Path Cancellation - Radio signals

being received from several directions

can cause distortion or fluttering. This

can be caused by a direct and reflect-

ed signal from the same station, or by

signals from two stations with close

frequencies. If this occurs, select

another station until the condition has

passed.

WARNING

Don't use a cellular phone when

you are driving. You should stop at

a safe place to use a cellular phone.

4 79

Features of your vehicle

Stereo radio operation (M445) (if equipped)

1. FM/AM Selection Button

2. Automatic Channel Selection Button

3. Power ON/OFF

4. Preset Button

5. TUNE/AUDIO Control Button

6. SCAN Button

7. AUTO STORE Button

SA-M445

4 80

Features of your vehicle

1. FM/AM Selection Button

4. Preset Button

Push [1]~[6]button less than 0.8 second

to play the channel saved in each button.

7. AUTO STORE Button

Turns to FM/AM mode and toggles FM1

and FM2➟AM➟FM1··· when the button is

pressed each time.

When the button is pressed, it automati-

cally selects and saves channels with

high reception rate to PRESET but-

tons(1~6) and plays the channel saved in

PRESET1.

Push preset button for 0.8 second or

longer to save the current channel to the

respective button with a beep.

2. Automatic Channel Selection

Button

If no channel is saved after AST, it will

play the previous channel.

When the [SEEK

] button is pressed, it

5. TUNE/AUDIO Control Button

reduces the band frequency by 100KHz

to automatically select a channel.

Turn this button clockwise by one notch

to increase frequency by 100KHz from

current frequency.

CAUTION

Stops at the previous frequency if no

channel is found.

• Do not place beverages close to

the audio system. The audio sys-

tem mechanism may be damaged

if you spill them.

Turn this button counterclockwise by one

notch to decrease frequency by 100KHz

from current frequency.

When the [SEEK

] button is pressed, it

increases the band frequency by 100KHz

to automatically select a channel.

Turns to AUDIO CONTROL mode, and

toggles in the order of BASS➟MIDDLE

➟TREBLE➟FADER➟BALANCE➟···BAS

S··· when the button is pressed each

time.

• Do not strike or allow anything to

impact the audio system, damage

to the system mechanisms could

occur.

Stops at the previous frequency if no

channel is found.

3. Power ON/OFF & Volume Control

Button

6. SCAN Button

Plays the first 10 seconds of each chan-

nel, when the button is pressed.

Turns ON/OFF when the IGNITION

SWITCH is on ACC or ON.

If the button is turned to the right, it

increases the volume and the button is

turned to the left, decreases the volume.

To cancel the mode, press the button

once again.

4 81

Features of your vehicle

Compact disc player operation (M445) (if equipped)

1. CD Loading Slot

2. CD Selection Button

3. CD Eject Button

4. AUX Selection Button

5. REW/FF Button

6. RANDOM Button

7. REPEAT Button

8. SCAN Button

9. Automatic Track Selection Button

SA-M445

4 82

Features of your vehicle

1. CD Loading Slot

Insert the CD with the label facing

upward.

5. Rewind / Fast Forward Button

7. REPEAT Button

Repeats the current song when the but-

ton is pressed for less than 0.8 second.

• Rewind Button

Press and hold [2 REW] button while

playing a CD then the player will play

the disk backwards 5 times the regular

speed for the first 5 seconds and 15

times faster after that. The sound will

be reduced by 12dB while you are

holding the button.

When the ignition switch is on ACC or

ON and the power is OFF, the power is

automatically turned on if the CD is

loaded.

Repeats the entire disc when the button

is pressed for 0.8 second or longer.

8. SCAN Button

Plays the first 10 seconds of each chan-

nel.

This CDP supports 12cm CDs. But if

VCD. Data CD, MP3 CD are loaded,

"Disc-Err" message will appear and the

CD will be ejected.

• Fast Forward Button

To cancel the mode, press the button

once again.

Press and hold [3 FF] button while

playing a CD then the player will play

the disk forward 5 times the regular

speed for the first 5 seconds and 15

times faster after that. The sound will

be reduced by 12dB while you are

holding the button.

2. CD Selection Button

9. Automatic Track Selection Button

If there is a CD in the CDP deck, it turns

to the CD mode when the button is

pressed each time.

• Push [SEEK

] button for less than

0.8 second to play from the beginning

of the current song.

• Push [SEEK

0.8 second and press again within 1

second to play the previous song.

] button for less than

3. CD Eject Button

6. RANDOM (RDM) Button

Push button to eject the CD during

CD playback.

You can listen to the tracks in random,

rather than sequential order.

To use random, do the following:

• Push [SEEK

or longer to rewind the current song.

• Push [SEEK ] button for less than

0.8 second to play the next song.

• Push [SEEK ] button for less than

] button for 0.8 second

This button is enabled when ignition

switch is off.

Press the RDM button to listen to record-

ed tracks in random sequence. Press

RDM again to cancel.

4. AUX Selection Button

If the auxiliary device is connected, it

turns to the AUX mode to play the sound

from the auxiliary player.

0.8 second or longer to fast-foward the

current song.

If there is no disc and the auxiliary device

is not connected, it will not turn to the

AUX mode.

4 83

Features of your vehicle

✽

NOTICE

(Continued)

CAUTION

• To assure proper operation of the unit,

keep the vehicle interior temperature

within a normal range by using the

vehicle's air conditioning or heating

system.

• When replacing the fuse, replace it

with a fuse having the correct capaci-

ty.

• All stored bookmarks are erased

when the car battery is disconnected

or power to the vehicle is lost. If this

occurs, the bookmarks will have to be

reset.

• This equipment is designed to be used

only in a 12 volt DC battery system

with negative ground.

• Avoid using recorded compact

discs in your audio unit. Original

compact discs are recommended

for best results.

• Do not insert warped or poor

quality discs into the CD player

as damage to the unit may occur.

• Do not insert anything such as

coins into the player slot as dam-

age to the unit may occur.

• Do not place beverages close to

the audio system. It may damage

the playback mechanism if you

spill them.

WARNING

When driving your vehicle, be sure

to keep the volume of the unit set

low enough to allow you to hear

sounds coming from the outside.

• Do not strike or allow anything to

impact the audio system, damage

to the system mechanisms could

occur.

• Off-road or rough surface driving

may cause the compact disc to

skip. Do not use the compact

disc when driving in such condi-

tions as damage to the compact

disc face could occur.

• This unit is made of precision parts.

Do not attempt to disassemble or

adjust any parts.

• Do not expose this equipment (includ-

ing the speakers and CD) to water or

excessive moisture.

• Do not attempt to grab or pull the

compact disc out while the disc is

being pulled into the audio unit

by self-loading mechanism.

Damage to the audio unit and

compact disc could occur.

(Continued)

4 84

Features of your vehicle

Stereo radio operation (PA710) (if equipped)

1. FM Selection Button

2. AM Selection Button

3. CD Selection Button

4. Power ON/OFF & Volume Control Button

5. Automatic Channel Selection Button

6. INFO Button

7. AUX Selection Button

8. AUTO STORE Button

9. SET UP Button

10. ENTER/TUNE Button

11. Preset Button

SA-PA710A

4 85

Features of your vehicle

1. FM Selection Button

5. Automatic Channel Selection

Button

8. AUTO STORE Button

Turns to FM mode and toggles FM1 ➟

FM2➟FM1··· when the button is pressed

each time.

When the button is pressed, it automati-

cally selects and saves channels with

high reception rate to PRESET buttons

(1~6) and plays the channel saved in

PRESET1.

• When the [SEEK

]button is pressed,

it reduces the band frequency by

100Khz to automatically select a chan-

nel.

2. AM Selection Button

Turns to AM mode and toggles AM when

the button is pressed each time.

If no channel is saved after the AUTO

STORE button is pressed, it will play the

previous channel.

Stops at the previous frequency if no

channel is found.

• When the [SEEK

]button is pressed,

it increases the band frequency by

100khz to automatically select a chan-

nel.

3. CD Selection Button

9. SET UP Button

Press this button to turn to the SOUND,

SCROLL adjustment mode.

If there is a CD in the CDP deck it turns

to the CD mode when the button is

pressed each time.

Stops at the previous frequency if no

channel is found.

If no action is taken for 5 seconds after

pressing the button, it will return to the

play mode.(After entering SET UP mode,

move between items using the left, right

and PUSH functions of the TUNE button.)

4. Power ON/OFF & Volume Control

Button

6. INFO Button

Displays the information of the channel

currently played by RDS.

• Turns on/off when the IGNITION

SWITCH is on ACC or ON. If the button

is turned to the right, it increases the

volume and left, decreases the vol-

ume.

The SET UP item changes from SOUND

(BASS, MIDDLE, TREBLE, FADER,

BALANCE, RETURN) ➟ SCROLL (ON,

OFF) ➟ RETURN.

7. AUX Selection Button

If the auxiliary device is connected, it

turns to AUX MODE to play the sound

from the auxiliary player.

• In AUX mode, the volume and tone

(BASS, MID, TRE) are adjusted in a

separate way.

If there is no disc and the auxiliary device

is not connected, it displays "NO MEDIA"

for 5 seconds and returns to the previous

mode.

If you pull out AUX from a jack and

insert it again, then only volume goes

back to 10-step.

4 86

Features of your vehicle

10. TUNE/ENTER Button

11. Preset Button

Push [1]~[6] buttons less than 0.8 second

to play the channel saved in each button.

Turn this button clockwise by one notch

to increase frequency by 100Khz from

current frequency.

Push the preset button for 0.8 second or

longer to save the current channel to the

respective button with a beep.

Turn this button counterclockwise by one

notch to decrease frequency by 100Khz

from current frequency.

Press this button while holding SET UP

button to activate / inactivate the item.

CAUTION

• Do not place beverages close to

the audio system. It may damage

the audio system mechanism if

you spill them.

Select SET UP item using left and right

function of the Tune button.

• Do not strike or allow anything to

impact the audio system, damage

to the system mechanisms could

occur.

4 87

Features of your vehicle

Compact disc player operation (PA710) (if equipped)

1. CD Loading Slot

2. CD Eject Button

3. CD Selection Button

4. Automatic Track Selection Button

5. INFO Button

6. ENTER/TUNE Button

7. REPEAT Button

8. RANDOM Button

9. AST (CD SCAN) Button

10. FOLDER Moving Button

UR-200SAD-CD

4 88

Features of your vehicle

1. CD Loading Slot

Insert the CD with the label facing

upward.

7. REPEAT Button

Repeats current song when the button is

pressed for less than 0.8 second.

• Push [SEEK

or longer to rewind the current song.

• Push [SEEK ] button for less than

0.8 second to play the next song.

• Push [SEEK ] button for less than

] button for 0.8 second

When the ignition switch is on ACC or

ON and the power is off, the power is

automatically turned on if the CD is

loaded.

Repeats the entire disc when the button

is pressed for 0.8 second or longer.

0.8 second or longer to fast-foward the

current song.

8. RANDOM (RDM) Button

You can listen to the tracks in random,

rather than sequential order.

To use random, do the following:

This CDP supports 12 cm CDs. But if

VCD, Data CD, MP3 CD are loaded, "Er-

6" message will appear and the CD will

be ejected.

5. INFO Button

Displays the information of the current

CD TRACK in the order of DISC

TITLE➟DISC ARTIST➟TRACK TITLE➟

TRACK ARTIST➟TOTAL TRACK➟ Play

Screen➟DISC TITLE➟···.(It is not dis-

played if the information is not available

on the disc.) (If MP3 is displayed FILE

NAME➟ TITLE➟ ARTIST➟ ALBUM➟

FOLDER➟TOTAL FILE➟FILE NAME➟···)

Press the RDM button to listen to record-

ed tracks in random sequence. Press

RDM again to cancel.

2. CD Eject Button

Push

button to eject the CD during

CD playback. This button is enabled

when ignition switch is off.

9. AST(CD SCAN) Button

Plays the first 10 seconds of each song

in the disc.

3. CD Selection Button

To cancel the mode, press the key once

again.

If there is a CD in the CDP deck, it turns

to the CD mode when the button is

pressed each time.

6. ENTER/TUNE Button

Turn this button clockwise to display

songs after the current song.

10. FOLDER Moving Button

• Moves [FLDR

] button child folder of

4. Automatic Track Selection Button

Also, turn this button counterclockwise to

display songs before the current song.

the current folder and displays the first

song in the folder. Press ENT/TUNE

button to move to the folder displayed.

It will play the first song in the folder.

• Push [SEEK

] button for less than

To listen to the displayed song, press the

button to skip to the song and play.

0.8 second to play from the beginning

of the current song.

• Push [SEEK

] button for less than

• Moves [FLDR

] button parent folder

0.8 second and press again within 1

seconds to play the previous song.

and displays the first song in the folder.

Press ENT/TUNE button to move to

the folder displayed. It will play the first

song in the folder.

4 89

Features of your vehicle

✽

NOTICE

(Continued)

CAUTION

• To assure proper operation of the unit,

keep the vehicle interior temperature

within a normal range by using the

vehicle's air conditioning or heating

system.

• When replacing the fuse, replace it

with a fuse having the correct capaci-

ty.

• The preset station frequencies are all

erased when the car battery is discon-

nected. Therefore, all data will have to

be set again if this should occur.

• Do not add any oil to the rotating

parts. Keep magnets, screwdrivers

and other metallic objects away from

the tape mechanism and head.

• This equipment is designed to be used

only in a 12 volt DC battery system

with negative ground.

• Avoid using recorded compact

discs in your audio unit. Original

compact discs are recommended

for best results.

• Do not insert warped or poor

quality discs into the CD player

as damage to the unit may occur.

• Do not insert anything like coins

into the player slot as damage to

the unit may occur.

• Do not place beverages close to

the audio system. It may damage

the playback mechanism if you

spill them.

WARNING

When driving your vehicle, be sure

to keep the volume of the unit set

low enough to allow you to hear

sounds coming from the outside.

• Do not strike or allow anything to

impact the audio system, damage

to the system mechanisms could

occur.

• Off-road or rough surface driving

may cause the compact disc to

skip. Do not use the compact

disc when driving in such condi-

tions as damage to the compact

disc face could occur.

• This unit is made of precision parts.

Do not attempt to disassemble or

adjust any parts.

• Do not expose this equipment (includ-

ing the speakers and tape) to water or

excessive moisture.

• Do not attempt to grab or pull the

compact disc out while the disc is

being pulled into the audio unit

by self-loading mechanism.

Damage to the audio unit and

compact disc could occur.

(Continued)

4 90

Features of your vehicle

USB (PA710) (if equipped)

1. AUX(USB) Selection Button

2. Track Moving Button

3. INFO Button

4. Folder moving Button

5. ENTER/TUNE Button

6. RANDOM Button

7. REPEAT Button

8. SCAN Button

SA-PA710C

4 91

Features of your vehicle

In case USB is connected to the multi-

media jack inside the consol on the right

hand side of the driver’s seat. When USB

is connected, the ‘USB’ icon will be dis-

played on the top right corner of the dis-

play screen.

3. INFO Button

6. RANDOM Button

Displays the information of the file cur-

rently played in the order of FILE NAME

➟TITLE➟ARTIST➟ALBUM➟FOLDER➟

TOTAL FILE➟FILE NAME➟… (Displays

no information if the file has no song

information.)

Press the button for less than 0.8 second

to start or stop the random playback of

the songs in the current folder.

Press the button for more than 0.8 sec-

ond to randomly play the entire songs in

the USB device.

1. AUX(USB) Selection Button

Press the button again to cancel the mode.

If the USB is connected, it switches to the

USB mode from the CD mode to play the

song files stored in the USB.

4. Folder moving Button

• If [FLDR

] button is pressed, it

7. REPEAT Button

Press the button for less than 0.8 second

to repeat the song currently played.

moves to the child folder of the current

folder and displays the first song in the

folder. Press ENTER/TUNE button to

move to the folder displayed. It will play

the first song in the folder.

If there are no CD and USB(AUX), it dis-

plays ‘NO MEDIA’.

Press the button for more than 0.8 sec-

ond to repeat the entire songs in the USB

device.

2. Track Moving Button

• Press the [SEEK

] button for less

• If [FLDR

] is button pressed, it

than 0.8 second to play from the begin-

ning of the song currently played.

moves to the parent folder and displays

the first song in the folder. Press

ENTER/TUNE button to move to the

folder displayed. It will play the first

song in the folder.

8. SCAN Button

Plays 10 seconds of each song in the

USB device.

Press the button for less than 0.8 sec-

ond and press it again within 1 second

to play the previous track.

Press the button once again to cancel

scanning.

Press the button for 0.8 second or

longer to play the song in reverse

direction in fast speed.

5. ENTER/TUNE Button

Turn this button clockwise to display the

songs next to the currently played song.

• Press the [SEEK

] button for less

Turn the button counterclockwise to dis-

play the songs before the currently

played song.

than 0.8 second to move to the next

track. Press the button for 0.8 second

or longer to play the song in forward

direction in fast speed.

Press the button to skip to the selected

song.

4 92

Features of your vehicle

(Continued)

CAUTION IN USING

USB DEVICE

• To use the external USB device,

make sure the device is not

mounted when starting up the

vehicle and mount the device

after starting up.

• Depending on the condition of

the external USB device, the con-

nected external USB device can

be unrecognizable.

• If you dismount the external USB

device during playback in USB

mode, the external USB device

can be damaged or malfunction.

Therefore, mount the external

USB device when the engine is

turned off or in another mode.

• When the formatted byte/sector

setting of External USB devices is

not either 512BYTE or 2048BYTE,

then the device will not be recog-

nized.

• If you start the vehicle when the

USB device is mounted, it may

damage the USB device. (USB is

not ESA)

• Depending on the type and

capacity of the external USB

device or the type of the files

stored in the device, there is a dif-

ference in the time taken for

recognition of the device, but this

is not an indicator of trouble and

you only have to wait.

• The USB device should only be

formatted to FAT 12/16/32.

• If the vehicle is started up or

turned off while the external USB

device is connected, the external

USB device may not work.

• USB device without USB I/F

authentication may not be recog-

nizable.

• Make sure the USB connection

terminal does not come in con-

tact with human body or any

object.

• It may not play inauthentic MP3 or

WMA files.

• Do not use the USB device for

other purposes than playing

music files.

1) It can only play MP3 files with

the compression rate between

8Kbps~320Kbps.

• Use of USB accessories such as

recharger or heater using USB I/F

may lower the performance or

cause trouble.

• If you repeat mounting or dis-

mounting USB device in a short

period of time, it may break the

device.

2) It can only play WMA music

files with the compression rate

between 8Kbps~320Kbps.

• If you use devices such as a USB

hub you purchased separately,

the vehicle’s audio system may

not recognize the USB device.

Connect the USB device directly

to the multimedia terminal of the

vehicle.

• You might hear a strange noise

when mounting or dismounting a

USB device.

• Take cautions for static electricity

when mounting or dismounting

the external USB device.

(Continued)

• An encoded MP3 PLAYER is not

recognizable.

(Continued)

4 93

Features of your vehicle

(Continued)

• If USB device is divided by logical

drives, only the music files on the

highest-priority drive are recog-

nized by car audio.

• Please avoid using USB memory

products which can be used as

key chains or cellular phone

accessories as they could cause

damage to the USB jack. Please

make certain only to use plug

type connector products as

shown below.

• Devices such as MP3 Player/

Cellular phone/Digital camera

those are not recognizable by

standard USB I/F can be unrecog-

nizable.

• USB devices other than standard-

ized goods (METAL COVER TYPE

USB) can be unrecognizable.

• USB flash memory reader (such

as CF, SD, microSD, etc.) or exter-

nal-HDD type devices can be

unrecognizable.

• Music files protected by DRM

(DIGITAL RIGHTS MANAGEMENT)

are not recognizalbe.

• The data in the USB memory may

lost while using this AUDIO, It is

recommeded to back up impor-

tant data on a personal.

(Continued)

4 94

Features of your vehicle

RUNNING iPod (PA710) (if equipped)

1. AUX(iPod) Selection Button

2. Track Moving Button

3. INFO Button

4. Category Selection Button

5. ENTER/TUNE Button

6. RANDOM Button

7. REPEAT Button

❈ iPod is a trademark of Apple Inc.

SA-PA710D

4 95

Features of your vehicle

In case the iPod exclusive cable is con-

nected to the multimedia jack inside the

consol on the right hand side of the dri-

ver’s seat. When the iPod is connected,

the ‘iPod’ icon will be displayed on the top

right corner of the display screen.

5. ENTER/TUNE Button

Turn this button clockwise to display the

songs next to the currently played song.

• Press the [SEEK

] button for less

than 0.8 second to move to the next

track. Press the button for 0.8 second

or longer to play the song in forward

direction in fast speed.

Turn the button counterclockwise to dis-

play the songs before the currently

played song.

Press the button to skip to the selected

song.

3. INFO Button

1. AUX(iPod) Selection Button

Displays the information of the file cur-

rently played in the order of FILE NAME

➟TITLE➟ARTIST➟ALBUM➟FOLDER➟

TOTAL FILE➟FILE NAME➟… (Displays

no information if the file has no song

information.)

If iPod is connected, it switches to the

iPod mode from the CD mode to play the

song files stored in the iPod.

6. RANDOM Button

Press the button for less than 0.8 second

to start or stop the random playback of

the songs in the current folder.

If there are no CD and AUX(iPod), it dis-

plays ‘NO MEDIA’

Press the button for longer than 0.8 sec-

ond to randomly play all songs in the

entire album of the iPod.

2. Track Moving Button

4. Category Selection Button

Moves to the upper category from cur-

rently played category of the iPod.

• Press the [SEEK

] button for less

than 0.8 second to play from the begin-

ning of the song currently played.

Press the button again to cancel the mode.

You will be able to search through the

lower category of the selected category.

Press the button for less than 0.8 sec-

ond and press it again within 1 second

to play the previous track.

7. REPEAT Button

Repeats the song currently played.

The order of iPod’s category is SONG,

ALBUMES, ARTISTS, GENRES, and

iPod. (Refer to the iPod user’s manual for

more information)

Press the button for 0.8 second or

longer to play the song in reverse

direction in fast speed.

4 96

Features of your vehicle

✽

NOTICE FOR USING iPod

DEVICE

(Continued)

CAUTION IN USING iPod

DEVICE

• When the iPod cable is connect-

ed, the system can be switched to

the AUX mode even without the

iPod device and can cause noise.

Disconnect the iPod cable when

you are not using the iPod device.

• Some iPod models might not support

the communication protocol and the

files will not be played. (iPod models

supported: Mini, 4G, Photo, Nano,

5G)

• The order of search or playback of

songs in the iPod can be different

from the order searched in the audio

system.

• You need the power cable exclu-

sive for an iPod in order to oper-

ate an iPod with the buttons on

the audio system. The PC cable

provided by Apple may cause a

malfunction and do not use it for

vehicle use.

• When the iPod is not used for the

audio system, the iPod cable has

to be separate from iPod devices.

Origin display of iPod may not be

displayed.

• When connecting the device with

an iPod cable, push in the jack

fully to not to interfere with com-

munication.

• If the iPod crashes due to its own

trouble, reset the iPod. (Reset: Refer

to iPod manual)

• When adjusting the sound effects

of an iPod and the audio system,

the sound effects of both devices

will overlap and might reduce or

distort the quality of the sound.

• iPod may not operate normally on

low battery.

• Deactivate (turn off) the equalizer

function of an iPod when adjust-

ing the audio system's volume,

and turn off the equalizer of the

audio system when using the

equalizer of an iPod.

(Continued)

4 97

Features of your vehicle

Stereo radio operation (H000) (if equipped)

1. FM/AM Selection Button

2. CD Selection Button

3. TA Selection Button

4. Power ON/OFF & Volume Control Button

5. Automatic Channel Selection Button

6. INFO Button

7. AUX Selection Button

8. AUTO STORE Button

9. SET UP Button

10. ENTER/TUNE Button

11. Preset Button

SA-H000A

4 98

Features of your vehicle

1. FM/AM Selection Button

5. Automatic Channel Selection

Button

8. AUTO STORE Button

Turns to FM/AM mode and toggles in the

order of FM1➟FM2➟FMA➟AM➟AMA➟

FM1··· when the button is pressed each

time.

• When you press the [AST] button, the

mode changes to 'Auto store Band'

and it saves the result. (FM1 or FM2

changes to FMA, AM changes to

AMA.)

• When the [SEEK

]button is pressed,

it reduces the band frequency by

50khz to automatically select a chan-

nel. Stops at the previous frequency if

no channel is found.

• When the button is pressed, it auto-

matically selects and saves channels

with high reception rate to PRESET

buttons (1~6) and plays the channel

saved in PRESET1.

2. CD Selection Button

If there is a CD in the CDP DECK it turns

to CD mode when the button is pressed

each time.

• When the [SEEK

]button is pressed,

it increases the band frequency by

50khz to automatically select a channel.

Stops at the previous frequency if no

channel is found.

If no channel is saved after the AUTO

STORE button is pressed, it will play

the previous channel.

3. TA Selection Button

In the FM, CD and AUX mode, you may

turn on/off the reception of the TA chan-

nels of RDS.

6. INFO Button

Displays the information of the channel

currently played by RDS.

9. SET UP Button

Press this button to turn to the SOUND,

RDS option, SCROLL adjustment mode.

4. Power ON/OFF & Volume Control

Button

7. AUX Selection Button

If no action is taken for 5 seconds after

pressing the button, it will return to the

play mode.(After entering SET UP mode,

• Turns on/off when the IGNITION

SWITCH is on ACC or ON. If the button

is turned to the right, it increases the

volume and left, decreases the vol-

ume.

If the auxiliary device is connected, it

turns to AUX MODE to play the sound

from the auxiliary player.

move between items using the left, right

and PUSH functions of the TUNE but-

ton.)

If there is no disc and the auxiliary device

is not connected, it displays "NO MEDIA"

for 5 seconds and returns to the previous

mode.

• In AUX mode, the volume and tone

(BASS, MID, TRE) are adjusted in a

separate way.

The SET UP item changes from SOUND

(BASS, MIDDLE, TREBLE, FADER,

BALANCE, RETURN) ➟ RDS(AF, REG,

NEWS, PTY, VOLUME, RETURN) ➟

SCROLL (ON, OFF) ➟ RETURN.

If you pull out AUX from a jack and

insert it again, then only volume goes

back to 10-step.

4 99

Features of your vehicle

10. ENTER/TUNE Button

11. Preset Button

Push [1]~[6] buttons less than 0.8 second

to play the channel saved in each button.

Turn this button clockwise by one notch

to increase frequency by 0.05Mhz from

current frequency.

Push the Preset button for 0.8 second or

longer to save the current channel to the

respective button with a beep.

Turn this button counterclockwise by one

notch to decrease frequency by 0.05Mhz

from current frequency.

Press this button while holding the SET

UP button to activate/inactivate the item.

CAUTION

• Do not place beverages close to

the audio system. It may damage

the playback mechanism if you

spill them.

Select a SET UP item using the left and

right function of the Tune button.

• Do not strike or allow anything to

impact the audio system, damage

to the system mechanisms could

occur.

4 100

Features of your vehicle

Compact disc player (H000) (if equipped)

1. CD Loading Slot

2. CD Eject Button

3. CD Selection Button

4. Automatic Track Selection Button

5. INFO Button

6. ENTER/TUNE Button

7. REPEAT Play Button

8. RANDOM Play Button

9. AST (CD SCAN) Play Button

10. FOLDER Moving Button

UR-200SAE-CD

4 101

Features of your vehicle

1. CD Loading Slot

Insert the CD with the label facing

upward.

8. RANDOM (RDM) Button

• Push [SEEK

0.8 second to play the next song.

• Push [SEEK ] button for less than

0.8 second or longer to fast-foward the

current song.

] button for less than

You can listen to the tracks in random,

rather than sequential order.

To use random, do the following:

When the ignition switch is on ACC or

ON and the power is off, the power is

automatically turned on if the CD is

loaded.

Press the RDM button to listen to record-

ed tracks in random sequence. Press

RDM again to cancel.

5. INFO Button

This CDP supports 12 cm CDs. But if

VCD, Data CD, MP3 CD are loaded, "Er-

6" message will appear and the CD will

be ejected.

Displays the information of the current

CD TRACK in the order of DISC

TITLE➟DISC ARTIST➟TRACK TITLE➟

TRACK ARTIST➟TOTAL TRACK➟ Play

Screen➟DISC TITLE➟···.(It is not dis-

played if the information is not available

on the disc.) (If MP3 is displayed

FILE NAME➟TITLE➟ARTIST➟ALBUM➟

FOLDER➟TOTAL FILE➟FILE NAME➟ ···)

9. AST(CD SCAN) Play Button

Plays the first 10 seconds of each song

in the disc.

To cancel the mode, press the key once

again.

2. CD Eject Button

Push

button to eject the CD during

CD playback. This button is enabled

when ignition switch is off.

10. FOLDER Moving Button

• Moves [FLDR

] button child folder of

the current folder and displays the first

song in the folder. Press ENT/TUNE

button to move to the folder displayed.

It will play the first song in the folder.

6. ENTER/TUNE Button

Turn this button clockwise to display

songs after the current song.

3. CD Selection Button

If there is a CD in the CDP deck, it turns

to the CD mode when the button is

pressed each time.

Also, turn this button counterclockwise to

display songs before the current song.

• Moves [FLDR

] button parent folder

and displays the first song in the folder.

Press ENT/TUNE button to move to

the folder displayed. It will play the first

song in the folder.

To listen to the displayed song, press the

button to skip to the song and play.

4. Automatic Track Selection Button

• Push [SEEK

] button for less than

0.8 second to play from the beginning

of the current song.

7.REPEAT Button

Repeats current song when the button is

pressed for less than 0.8 second.

• Push [SEEK

] button for less than

0.8 second and press again within 1

seconds to play the previous song.

Repeats the entire disc when the button

is pressed for 0.8 second or longer.

• Push [SEEK ] button for 0.8 second

or longer to rewind the current song.

4 102

Features of your vehicle

✽

NOTICE

(Continued)

CAUTION

• To assure proper operation of the unit,

keep the vehicle interior temperature

within a normal range by using the

vehicle's air conditioning or heating

system.

• When replacing the fuse, replace it

with a fuse having the correct capaci-

ty.

• All stored bookmarks are erased

when the car battery is disconnected

or power to the vehicle is lost. If this

occurs, the bookmarks will have to be

reset.

• This equipment is designed to be used

only in a 12 volt DC battery system

with negative ground.

• Avoid using recorded compact

discs in your audio unit. Original

compact discs are recommended

for best results.

• Do not insert warped or poor

quality discs into the CD player

as damage to the unit may occur.

• Do not insert anything like coins

into the player slot as damage to

the unit may occur.

• Do not place beverages close to

the audio system. It may damage

the playback mechanism if you

spill them.

WARNING

When driving your vehicle, be sure

to keep the volume of the unit set

low enough to allow you to hear

sounds coming from the outside.

• Do not strike or allow anything to

impact the audio system, damage

to the system mechanisms could

occur.

• Off-road or rough surface driving

may cause the compact disc to

skip. Do not use the compact

disc when driving in such condi-

tions as damage to the compact

disc face could occur.

• This unit is made of precision parts.

Do not attempt to disassemble or

adjust any parts.

• Do not expose this equipment (includ-

ing the speakers and CD) to water or

excessive moisture.

• Do not attempt to grab or pull the

compact disc out while the disc is

being pulled into the audio unit

by the self-loading mechanism.

Damage to the audio unit and

compact disc could occur.

(Continued)

4 103

Features of your vehicle

USB (H000) (if equipped)

1. AUX(USB) Selection Button

2. Track Moving Button

3. INFO Button

4. Folder moving Button

5. ENTER/TUNE Button

6. RANDOM Button

7. REPEAT Button

8. SCAN Button

SA-H000B

4 104

Features of your vehicle

In case USB is connected to the multi-

media jack inside the consol on the right

hand side of the driver’s seat. When USB

is connected, the ‘USB’ icon will be dis-

played on the top right corner of the dis-

play screen.

3. INFO Button

6. RANDOM Button

Displays the information of the file cur-

rently played in the order of FILE NAME

➟TITLE➟ARTIST➟ALBUM➟FOLDER➟

TOTAL FILE➟FILE NAME➟… (Displays

no information if the file has no song

information.)

Press the button for less than 0.8 second

to start or stop the random playback of

the songs in the current folder.

Press the button for more than 0.8 sec-

ond to randomly play the entire songs in

the USB device.

1. AUX(USB) Selection Button

Press the button again to cancel the mode.

If USB is connected, it switches to the

USB mode from the CD mode to play the

song files stored in the USB.

4. Folder moving Button

• If [FLDR

] button is pressed, it

7. REPEAT Button

Press the button for less than 0.8 second

to repeat the song currently played.

moves to the child folder of the current

folder and displays the first song in the

folder. Press ENTER/TUNE button to

move to the folder displayed. It will play

the first song in the folder.

If there are no CD and USB(AUX), it dis-

plays ‘NO MEDIA’.

Press the button for more than 0.8 sec-

ond to repeat the entire songs in the USB

device.

2. Track Moving Button

• Press the [SEEK

] button for less

• If [FLDR

] is button pressed, it

than 0.8 second to play from the begin-

ning of the song currently played.

moves to the parent folder and displays

the first song in the folder. Press

ENTER/TUNE button to move to the

folder displayed. It will play the first

song in the folder.

8. SCAN Button

Plays 10 seconds of each song in the

USB device.

Press the button for less than 0.8 sec-

ond and press it again within 1 second

to play the previous track.

Press the button once again to cancel

scanning.

Press the button for 0.8 second or

longer to play the song in reverse

direction in fast speed.

5. ENTER/TUNE Button

Turn this button clockwise to display the

songs next to the currently played song.

• Press the [SEEK

] button for less

Turn the button counterclockwise to dis-

play the songs before the currently

played song.

than 0.8 second to move to the next

track. Press the button for 0.8 second

or longer to play the song in forward

direction in fast speed.

Press the button to skip to the selected

song.

4 105

Features of your vehicle

(Continued)

CAUTION IN USING

USB DEVICE

• To use the external USB device,

make sure the device is not

mounted when starting up the

vehicle and mount the device

after starting up.

• Depending on the condition of

the external USB device, the con-

nected external USB device can

be unrecognizable.

• If you dismount the external USB

device during playback in USB

mode, the external USB device

can be damaged or malfunction.

Therefore, mount the external

USB device when the engine is

turned off or in another mode.

• When the formatted byte/sector

setting of External USB devices is

not either 512BYTE or 2048BYTE,

then the device will not be recog-

nized.

• If you start the vehicle when the

USB device is mounted, it may

damage the USB device. (USB is

not ESA)

• Depending on the type and

capacity of the external USB

device or the type of the files

stored in the device, there is a dif-

ference in the time taken for

recognition of the device, but this

is not an indicator of trouble and

you only have to wait.

• Use only a USB device formatted

to FAT 12/16/32.

• If the vehicle is started up or

turned off while the external USB

device is connected, the external

USB device may not work.

• USB device without USB I/F

authentication may not be recog-

nizable.

• Make sure the USB connection

terminal does not come in con-

tact with human body or any

object.

• It may not play inauthentic MP3 or

WMA files.

• Do not use the USB device for

other purposes than playing

music files.

1) It can only play MP3 files with

the compression rate between

8Kbps~320Kbps.

• Use of USB accessories such as

recharger or heater using USB I/F

may lower the performance or

cause trouble.

• If you repeat mounting or dis-

mounting USB device in a short

period of time, it may break the

device.

2) It can only play WMA music

files with the compression rate

between 8Kbps~320Kbps.

• If you use devices such as a USB

hub you purchased separately,

the vehicle’s audio system may

not recognize the USB device.

Connect the USB device directly

to the multimedia terminal of the

vehicle.

• You might hear a strange noise

when mounting or dismounting a

USB device.

• Take cautions for static electricity

when mounting or dismounting

the external USB device.

(Continued)

• An encoded MP3 PLAYER is not

recognizable.

(Continued)

4 106

Features of your vehicle

(Continued)

• If USB device is divided by logical

drives, only the music files on the

highest-priority drive are recog-

nized by car audio.

• Please avoid using USB memory

products which can be used as

key chains or cellular phone

accessories as they could cause

damage to the USB jack. Please

make certain only to use plug

type connector products as

shown below.

• Devices such as MP3 Player/

Cellular phone/Digital camera

those are not recognizable by

standard USB I/F can be unrecog-

nizable.

• USB devices other than standard-

ized goods (METAL COVER TYPE

USB) can be unrecognizable.

• USB flash memory reader (such

as CF, SD, microSD, etc.) or exter-

nal-HDD type devices can be

unrecognizable.

• Music files protected by DRM

(DIGITAL RIGHTS MANAGEMENT)

are not recognizalbe.

• The data in the USB memory may

lost while using this AUDIO, It is

recommeded to back up impor-

tant data on a personal.

(Continued)

4 107

Features of your vehicle

RUNNING iPod (H000) (if equipped)

1. AUX(iPod ) Selection Button

2. Track Moving Button

3. INFO Button

4. Category Selection Button

5. ENTER/TUNE Button

6. RANDOM Button

7. REPEAT Button

SA-PA710F

4 108

Features of your vehicle

In case the iPod exclusive cable is con-

nected to the multimedia jack inside the

consol on the right hand side of the dri-

ver’s seat. When the iPod is connected,

the ‘iPod’ icon will be displayed on the top

right corner of the display screen.

5. ENTER/TUNE Button

Turn this button clockwise to display the

songs next to the currently played song.

• Press the [SEEK

] button for less

than 0.8 second to move to the next

track. Press the button for 0.8 second

or longer to play the song in forward

direction in fast speed.

Turn the button counterclockwise to dis-

play the songs before the currently

played song.

Press the button to skip to the selected

song.

3. INFO Button

1. AUX(iPod) Selection Button

Displays the information of the file cur-

rently played in the order of FILE NAME

➟TITLE➟ARTIST➟ALBUM➟FOLDER➟

TOTAL FILE➟FILE NAME➟… (Displays

no information if the file has no song

information.)

If iPod is connected, it switches to the

iPod mode from the CD mode to play the

song files stored in the iPod.

6. RANDOM Button

Press the button for less than 0.8 second

to activate or deactivate the random play-

back of the songs within the current cat-

egory.

If there are no CD and AUX(iPod), it dis-

plays ‘NO MEDIA’.

2. Track Moving Button

Press the button for longer than 0.8 sec-

ond to randomly play all songs in the

entire album of the iPod.

4. Category Selection Button

Moves to the upper category from cur-

rently played category of the iPod.

• Press the [SEEK

] button for less

than 0.8 second to play from the begin-

ning of the song currently played.

Press the button once again to cancel

the mode.

You will be able to search through the

lower category of the selected category.

Press the button for less than 0.8 sec-

ond and press it again within 1 second

to play the previous track.

The order of iPod’s category is SONG,

ALBUMES, ARTISTS, GENRES, and

iPod. (Refer to the iPod user’s manual for

more information)

7. REPEAT Button

Repeats the song currently played.

Press the button for 0.8 second or

longer to play the song in reverse

direction in fast speed.

4 109

Features of your vehicle

✽

NOTICE FOR USING iPod

DEVICE

(Continued)

CAUTION IN USING iPod

DEVICE

• When the iPod cable is connect-

ed, the system can be switched to

the AUX mode even without the

iPod device and can cause noise.

Disconnect the iPod cable when

you are not using the iPod device.

• Some iPod models might not support

the communication protocol and the

files will not be played. (iPod models

supported: Mini, 4G, Photo, Nano,

5G)

• The order of search or playback of

songs in the iPod can be different

from the order searched in the audio

system.

• You need the power cable exclu-

sive for an iPod in order to oper-

ate an iPod with the buttons on

the audio system. The PC cable

provided by Apple may cause a

malfunction and do not use it for

vehicle use.

• When the iPod is not used for the

audio system, the iPod cable has

to be separate from iPod devices.

Origin display of iPod may not be

displayed.

• When connecting the device with

an iPod cable, push in the jack

fully to not to interfere with com-

munication.

• If the iPod crashes due to its own

trouble, reset the iPod. (Reset: Refer

to iPod manual)

• When adjusting the sound effects

of an iPod and the audio system,

the sound effects of both devices

will overlap and might reduce or

distort the quality of the sound.

• iPod may not operate normally on

low battery.

• Deactivate (turn off) the equalizer

function of an iPod when adjust-

ing the audio system's volume,

and turn off the equalizer of the

audio system when using the

equalizer of an iPod.

(Continued)

4 110

Features of your vehicle for Your Kia Picanto 4 Door First Generation (2004-2010)

Related Topics

Popular Owner Manuals

Latest Owner Manuals