Get In case of an emergency Guide for Kia Sportage SUV Second Generation (2004-2010)

Road warning / 6-2

Overheating / 6-3

Emergency starting / 6-4

Electrical circuit protection / 6-7

Towing / 6-14

If you have a flat tire / 6-19

In case of an emergency

ROAD WARNING

Depress the flasher switch with the

ignition switch in any position. The

flasher switch is located in the center

console switch panel. All turn signal

lights will flash simultaneously.

• The hazard warning flasher oper-

ates whether your vehicle is run-

ning or not.

• The turn signals do not work when

the hazard flasher is on.

1KMN2109

• Care must be taken when using

Hazard warning flasher

the hazard warning flasher while

The hazard warning flasher serves

the vehicle is being towed.

as a warning to other drivers to exer-

cise

extreme

caution

when

approaching, overtaking, or passing

your vehicle. It should be used when-

ever emergency repairs are being

made or when the vehicle is stopped

near the edge of a roadway.

6 2

In case of an emergency

OVERHEATING

If your temperature gauge indicates

If coolant is not boiling out, allow

WARNING - Removing

overheating, if you experience a loss

the engine to idle and open the

of power, or if you hear a loud knock-

hood to permit the engine to cool

radiator cap

ing or pinging noise, the engine has

gradually.

Do not remove the radiator cap

probably overheated. Should any of

If the temperature does not go

when the engine and radiator

these symptoms occur, use the fol-

down with the engine idling, stop

are hot. Scalding hot coolant

lowing procedure:

the engine and allow sufficient

and steam may blow out under

1. Turn on the hazard warning flash-

time for it to cool.

pressure. This could cause seri-

er, then drive to the nearest safe

ous injury.

4. The coolant level should then be

location and stop your vehicle; set

checked. If the level in the reser-

the automatic transaxle in P

voir is low, look for leaks at the

If the engine frequently overheats,

(Park), or shift the manual

radiator hoses and connections,

have the cooling system checked

transaxle to N (Neutral) and apply

heater hoses and connections,

and repaired by an Authorized Kia

the parking brake.

radiator, and water pump. If you

Dealer.

2. Make sure the air conditioner is

find a major leak or another prob-

off.

lem that may have caused the

engine to overheat, do not operate

3. If coolant or steam is boiling out of

the engine until it has been cor-

the radiator, stop the engine and

rected. Call an Authorized Kia

call an Authorized Kia Dealer for

Dealer for assistance. If you do not

assistance.

find a leak or other problem, care-

fully add coolant to the reservoir.

6 3

In case of an emergency

EMERGENCY STARTING

Jump starting

✽ NOTICE

WARNING - Battery

Use only a 12-volt jumper system.

Jump starting can be dangerous if

• Keep all flames or sparks

You can damage a 12-volt starting

done incorrectly. Therefore, to avoid

away from the battery. The bat-

motor, ignition system, and other

harm to yourself or damage to your

tery produces hydrogen gas

electrical parts beyond repair by use

vehicle or battery, follow the jump

which may explode if exposed

of a 24-volt power supply (either two

starting procedures listed on page

to flame or sparks.

12-volt batteries in series or a 24-

6-6. If in doubt, we strongly recom-

volt motor generator set).

mend that you have a competent

• Do not attempt to jump start

technician or towing service jump

the vehicle if the discharged

start your vehicle.

battery is frozen or if the elec-

WARNING - Battery

trolyte level is low; the battery

Never attempt to check the elec-

may rupture or explode.

trolyte level of the battery as

this may cause the battery to

rupture or explode causing seri-

ous injury.

6 4

In case of an emergency

Connecting jumper cables

Connect cables in numerical order and

disconnect in reverse order.

➀ (+)

➁ (+)

Discharged battery

➂ (-)

Booster battery

➃ (-)

Jumper Cables

1KMN4001

6 5

In case of an emergency

Jump starting procedure

Push-starting

CAUTION - Battery cables

1. Make sure the booster battery is

Your manual transaxle-equipped

Do not connect the jumper

12-volt and that its negative termi-

vehicle should not be push-started

cable from the negative terminal

nal is grounded.

because it might damage the emis-

of the booster battery to the

2. If the booster battery is in another

sion control system.

negative terminal of the dis-

vehicle, do not allow the vehicles

Vehicles equipped with automatic

charged battery. This can cause

to touch.

transaxle cannot be push-started.

the discharged battery to over-

3. Turn off all unnecessary electrical

heat and crack, releasing bat-

Follow the directions in this section

loads.

tery acid.

for jump-starting.

4. Connect the jumper cables in the

exact sequence shown in the pre-

CAUTION

Do not allow the jumper cables to

vious illustration. First connect one

contact anything except the cor-

Never tow a vehicle to start it

end of a jumper cable to the posi-

rect battery terminals or the cor-

tive terminal of the discharged bat-

because the sudden surge for-

tery ( ➀ ), then connect the other

rect ground. Do not lean over the

ward when the engine starts

end to the positive terminal on the

battery when making connections.

could cause a collision with the

booster battery ( ➁ ). Proceed to

tow vehicle.

5. Start the engine of the vehicle with

connect one end of the other

the booster battery and let it run at

jumper cable to the negative ter-

2,000 rpm, then start the engine of

minal of the booster battery ( ➂ ),

the vehicle with the discharged

then the other end to a solid, sta-

battery.

tionary, metallic point (for exam-

If the cause of your battery discharg-

ple, the engine lifting bracket)

ing is not apparent, you should have

away from the battery ( ➃ ). Do not

your vehicle checked by an

connect it to or near any part that

Authorized Kia Dealer.

moves when the engine is

cranked.

Refer to illustration on page 6-5.

6 6

In case of an emergency

ELECTRICAL CIRCUIT PROTECTION

If any of your vehicle’s lights, acces-

If the replacement fuse blows, this

Standard

sories, or controls do not work, check

indicates an electrical problem. Avoid

the appropriate circuit fuse. If a fuse

using the system involved and imme-

has blown, the element inside the

diately consult an Authorized Kia

fuse will be melted.

Dealer.

Normal

Blown

If the electrical system does not

Two kinds of fuses are used: stan-

Main fuse

work, first check the driver’s side

dard for lower amperage rating and

fuse panel.

main for higher amperage ratings.

Always replace a blown fuse with

one of the same rating.

Blown

Normal

1LDA4002

Fuses

A vehicle’s electrical system is pro-

tected from electrical overload dam-

age by fuses.

This vehicle has two fuse panels,

one located in the driver's side panel

bolster, the other in the engine com-

partment near the battery.

6 7

In case of an emergency

Fuse replacement

WARNING - Fuse replace-

ment

• Never replace a fuse with any-

thing but another fuse of the

same rating.

• A higher capacity fuse could

cause damage possibly a fire.

• Never install a wire instead of

the proper fuse - even as a

1KMB4003

1KMA4004

temporary repair. It may cause

Driver’s side panel

5. Push in a new fuse of the same

extensive wiring damage and

rating, and make sure it fits tightly

1. Turn the ignition switch and all

possibly a fire.

in the clips.

other switches off.

If it fits loosely, consult an Authorized

2. Open the left side trim of the dri-

Kia Dealer.

ver’s instrument panel. Do not

✽ NOTICE

If you do not have a spare, use a

remove the trim from the panel

Do not use a screwdriver or any

fuse of the same rating from a circuit

completely.

other metal object to remove fuses

you may not need for operating the

3. Pull the suspected fuse straight

because it may cause a short circuit

vehicle, such as the cigar lighter

out. Use the removal tool provided

and damage the system.

fuse.

in the fuse panel.

If the headlights or other electrical

4. Check the removed fuse; replace it

components do not work and the

if it is blown.

fuses are OK, check the fuse block in

Spare fuses are provided in the

the engine compartment. If a fuse is

fuse panel.

blown, it must be replaced.

6 8

In case of an emergency

✽ NOTICE

After checking the fuse box in the

engine compartment, securely

install the fuse box cover. If not,

electrical failures may occur from

water leaking in.

1KMB4006

1KMA4008

Engine compartment

Main fuse

1. Turn the ignition switch and all

If the ALT fuse is blown, it must be

other switches off.

removed as follows:

2. Remove the fuse box cover by

1. Disconnect the negative battery

pressing the taps on both ends

cable.

and pulling up.

2. Remove the screws shown in the

3. Check the removed fuse; replace it

picture above.

if it is blown. To remove or insert

3. Replace the fuse with a new one

the fuse, use the fuse puller in the

of the same rating.

driver's side panel in the vehicle.

4. Reinstall in the reverse order of

4. Push in a new fuse of the same

removal.

rating, and make sure it fits tightly

in the clips.

✽ NOTICE

If it fits loosely, consult an Authorized

Kia Dealer.

If the ALT fuse is blown, consult an

Authorized Kia Dealer.

6 9

In case of an emergency

Fuse/Relay panel description

Inside the fuse/relay box covers, you can find the fuse/relay label describing fuse/relay name and capacity.

Driver’s side panel

Engine compartment

1KMA4009/1KMR4010

6 10

In case of an emergency

Driver side panel

Description

Fuse rating

Protected component

Description

Fuse rating

Protected component

TAIL RH

10A

Taillight (right)

P/WDW-2

30A

Power window (right)

RR HTR

30A

Rear defroster

SPARE

10A

Spare fuse

HAZARD

15A

Hazard warning light

IG COIL

20A

Ignition coil

SAFETY P/WDW

15A

Safety power window

T/SIG

15A

Turn signal light

HTD MIRR

10A

Outside rearview mirror defroster

A/BAG IND

10A

Cluster

TAIL LH

10A

Taillight (left)

CLUSTER

10A

Cluster

ECU (B+)

10A

TCU, Immobilizer

SPARE FUSE

15A

Spare fuse

15A

Power outlet (rear)

SPARE FUSE

10A

Spare fuse

RR FOG

10A

Rear fog lamp

B/UP

10A

Back-up light

RR WIPER

15A

Rear wiper

A/BAG

15A

Airbag

F/MIRROR

10A

Folding the outside rearview mirror

ABS

10A

Anti-lock brake system

Ignition lock/inhibitor switch,

ECU

10A

TCS, ESP, Immobilizer

START

10A

Theft-alarm system

SPARE FUSE

30A

Spare fuse

10A

Audio

SPARE FUSE

20A

Spare fuse

15A

Power outlet (front)

P/CONN

30A

Power connector fuse

OBD II

10A

OBD II, Diagonosis

SHUNT CONN

Shunt connector

S/HTR

20A

Seat warmer

SPARE

15A

Spare fuse

C/LIGHTER

15A

Cigar lighter

ETACS, Audio, Door lock,

AUDIO

10A

Electric remote control mirror

Cluster, ETACS, A/C, Clock,

ROOM LP

10A

Room lamp

S/ROOF & D/LOCK

20A

Sunroof, Door lock

A/CON

10A

Air conditioner

IGN

10A

Fuel filter heater, AQS, Headlight

P/WDW-1

30A

Power window (left)

6 11

In case of an emergency

Engine compartment

Description

Fuse rating

Protected component

Description

Fuse rating

Protected component

A/CON

Air conditioner relay

DRL

15A

Daytime running light

ATM

Automatic transaxle control relay

F/FOG

15A

Front fog light

COND2

Condenser (low) relay

F/PUMP

15A

Fuel pump

DEICE

Defroster relay

F/WIPER

20A

Front wiper

F/FOG

Front fog light relay

HDLP HI

20A

Headlight (high)

F/PUMP

Fuel pump relay

HDLP LO

15A

Headlight (low)

HDLP HI

Headlight (high) relay

HORN

15A

Horn

HDLP LO

Headlight (low) relay

INJ

15A

Injector

HORN

Horn relay

STOP

15A

Stop light

WIPER

Wiper relay

4WD

20A

4WD ECM

COND1

Condenser (high) relay

AMP

20A

Amplifier

MAIN

Main relay

ATM

20A

Automatic transaxle control

START

Start motor relay

ECU

30A

Engine control unit

COND1

40A

Condenser (high)

SPARE

10A

Spare fuse

COND2

30A

Condenser (low)

SPARE

15A

Spare fuse

IGN1

30A

Ignition switch

SPARE

20A

Spare fuse

IGN2

30A

Start motor

SPARE

30A

Spare fuse

ABS1

40A

ABS, ESP

ABS2

40A

ABS, ESP

IP B+

60A

In panel B+

BLOWER

40A

Blower

2.0L Gasoline

120A

ALT

Alternator

2.7L Gasoline

140A

A/CON

10A

Air conditioner

SNSR

10A

Sensors

DEICE

15A

Defroster

6 12

In case of an emergency

✽ NOTICE

• If the power connector fuse is

pulled up from the fuse panel, the

warning chime, audio, clock and

interior lamps, etc., will not oper-

Power connector fuse

ate. Some items must be reset after

replacement. (Refer to “Items to

be reset···.” on page 7-32)

• Even though the power connector

fuse is pulled up, the battery can

still be discharged by operation of

the headlights or other electrical

1KMA4005

devices.

Power connector fuse

Your vehicle is equipped with a

power connector fuse to prevent bat-

tery discharge if your vehicle is

parked without being operated for

prolonged periods. Use the following

procedures before parking the vehi-

cle for prolonged period.

1. Turn off the engine.

2. Turn off the headlights and tail

lights.

3. Open the driver’s side panel cover

and pull up the “P/CONN 30A”.

6 13

In case of an emergency

TOWING

1KMA4022

1KMA4023

1KMA4024

If emergency towing is necessary,

On 4WD vehicles, your vehicle

On 2WD vehicles, it is acceptable to

we recommend having it done by an

must be towed with a wheel lift

tow the vehicle with the rear wheels

authorized Kia dealer or a commer-

and dollies or flatbed equipment

on the ground (without dollies) and

cial tow-truck service. Proper lifting

with all the wheels off the ground.

the front wheels off the ground.

and towing procedures are neces-

When being towed by a commercial

sary to prevent damage to the vehi-

tow truck and wheel dollies are not

cle. The use of wheel dollies or

used, the front of the vehicle should

flatbed is recommended.

always be lifted, not the rear.

For trailer towing guidelines informa-

tion, refer to section 5 “Driving Tips”.

6 14

In case of an emergency

When towing your vehicle in an

emergency without wheel dollies :

1. Set the ignition switch in the ACC

position.

2. Place the transaxle shift lever in N

(Neutral).

3. Release the parking brake.

1KMB4025

✽ NOTICE

Failure to place the transaxle shift

lever in N (Neutral) may cause inter-

nal damage to the transaxle.

1GHA4105A

✽ NOTICE

• Do not tow the vehicle backwards

with the front wheels on the

ground as this may cause damage

to the vehicle.

• Do not tow with sling-type equip-

ment. Use wheel lift or flatbed

equipment.

6 15

In case of an emergency

Towing with a vehicle other

Towing in this manner may be done

• Front

than a tow truck

only on hard-surfaced roads for a

short distance and at low speeds.

If towing is necessary, we recom-

Also, the wheels, axles, power train,

mend you to have it done by an

steering and brakes must all be in

Authorized Kia dealer or a commer-

good condition.

cial tow truck service.

• Do not use the tow hooks to pull a

If towing service is not available in an

vehicle out of mud, sand or other

emergency, your vehicle may be

conditions from which the vehicle

temporarily towed using a cable or

cannot be driven out under its own

chain secured to the emergency tow-

6KMA4026

power.

ing hook under the front or rear of the

• Rear

• Avoid towing a vehicle heavier than

vehicle. Use extreme caution when

the vehicle doing the towing.

towing the vehicle. A driver must be

in the vehicle to steer it and operate

the brakes.

1KMA4027

6 16

In case of an emergency

✽ NOTICE

CAUTION

• Attach a towing strap to the tow

Use extreme caution when tow-

hook.

ing the vehicle.

• Using a portion of the vehicle

• Avoid sudden starts or erratic

other than the tow hooks for tow-

driving maneuvers which

ing may damage the body of your

would place excessive stress

vehicle.

on the emergency towing

• Use only a cable or chain specifi-

hook and towing cable or

cally intended for use in towing

chain. The hook and towing

vehicles. Securely fasten the cable

cable or chain may break and

or chain to the towing hook pro-

cause serious injury or dam-

vided.

1KMA4028

age.

• Use a towing strap less than 5 m

• Before emergency towing, check

• If the towing vehicle can hard-

(16 feet) long. Attach a white or red

that the hook is not broken or dam-

ly move, do not forcibly con-

cloth (about 30 cm (12 inches)

aged.

tinue the towing. Contact an

wide) in the middle of the strap for

Authorized Kia dealer or a

easy visibility.

• Fasten the towing cable or chain

commercial tow truck service

securely to the hook.

• Drive carefully so that the towing

for assistance.

strap is not loosened during tow-

• Do not jerk the hook. Apply steady

• Tow the vehicle as straight

ing.

and even force.

ahead as possible.

• To avoid damaging the hook, do

• Keep away from the vehicle

not pull from the side or at a verti-

during towing.

cal angle. Always pull straight

ahead.

6 17

In case of an emergency

When your vehicle is being

• Press the brake pedal with more

Tips for towing a stuck vehicle

towed by another vehicle

force than normal since you will

The following methods are effective

have reduced brake performance.

other than a tow truck (in case

when your vehicle is stuck in mud,

of an emergency)

• More steering effort will be

sand or similar substances that pre-

required because the power steer-

vent the vehicle from being driven

• Turn the ignition switch to ACC so

ing system will be disabled.

out under its own power.

the steering wheel isn’t locked.

• If you are driving down a long hill,

• Remove the soil and sand, etc.

• Place the transaxle shift lever in N

the brakes may overheat and brake

from the front and the back of the

(Neutral).

performance will be reduced. Stop

tires.

• Release the parking bake.

often and let the brakes cool off.

• Place a stone or wood under the

• Vehicles equipped with automatic

tires.

transaxles should not exceed 45

✽ NOTICE

km/h (28 mph) and should not be

towed more than 80 km (50 miles).

To prevent internal damage to the

transaxle, never tow your vehicle

• Vehicles equipped with manual

from the rear (backwards) with all

transaxle should not be towed in

four tires in contact with the sur-

excess of 88 km/h (55 mph) and

face.

should not be towed more than

645 km (400 miles).

6 18

In case of an emergency

IF YOU HAVE A FLAT TIRE

Important - use of compact

spare tire

your vehicle is equipped with a com-

pact spare tire. This compact spare

tire takes up less space than a regu-

lar-size tire. This tire is smaller than a

conventional tire and is designed for

temporary use only.

CAUTION

• You should drive carefully

1KMN4012

1KMA4014

when the compact spare is in

The spare tire, jack, jack handle,

Removing the spare tire

use. The compact spare

wheel lug nut wrench are stored in

Turn the tire hold-down wing bolt

should be replaced by the

the luggage compartment. Remove

counterclockwise.

proper conventional tire and

the luggage under tray out of the way

rim at the first opportunity.

Store the tire in the reverse order of

to reach this equipment.

removal.

• The operation of this vehicle

is not recommended with

To prevent the spare tire and tools

more than one compact spare

from “rattling” while the vehicle is in

tire in use at the same time.

motion, store them properly.

6 19

In case of an emergency

When using a compact spare tire,

• Do not take this vehicle through an

CAUTION

observe the following precautions:

automatic car wash.

This spare tire should be used

• Under no circumstances should

• This tire should not be installed on

only for VERY short distances.

you exceed 80 km/h (50 mph); a

the front axle if the vehicle must be

Compact spares should NEVER

higher speed could damage the

driven in snow or on ice.

be used for long drives or

tire.

• Do not use the compact spare tire

extended distances.

• Ensure that you drive slowly

on any other vehicle because this

enough for the road conditions to

tire has been designed especially

avoid all hazards. Any road hazard,

for your vehicle.

The compact spare should be inflat-

such as a pothole or debris, could

ed to 420 kPa (60 psi).

• The compact spare tire’s tread life

seriously damage the compact

is shorter than a regular tire.

spare.

Inspect your compact spare tire

✽ NOTICE

• Any continuous road use of this tire

regularly and replace worn com-

Check the inflation pressure after

could result in tire failure, loss of

pact spare tires with the same size

installing the spare tire. Adjust it to

vehicle control, and possible per-

and design, mounted on the same

the specified pressure, as necessary.

sonal injury.

wheel.

• Do not exceed the vehicle’s maxi-

mum load rating or the load-carry-

ing capacity shown on the sidewall

of the compact spare tire.

• Avoid driving over obstacles. The

compact spare tire diameter is

smaller than the diameter of a con-

ventional tire and reduces the

ground clearance approximately

25 mm (1 inch), which could result

in damage to the vehicle.

6 20

In case of an emergency

(Continued)

WARNING - Changing

• The vehicle can easily roll off

tires

the jack causing serious

• Never attempt vehicle repairs

injury or death. No person

in the traffic lanes of a public

should place any portion of

road or highway.

their body under a vehicle that

• Always move the vehicle com-

is supported only by a jack ;

pletely off the road and onto

use vehicle support stands.

the shoulder before trying to

• Do not start or run the engine

change a tire. The jack should

while the vehicle is on the

be used on level firm ground.

jack.

1KMA4013

If you cannot find a firm, level

• Do not allow anyone to remain

place off the road, call a tow-

Changing tires

in the vehicle while it is on the

ing service company for

Jacking instructions

jack.

assistance.

The jack is provided for emergency

• Make sure any children pre-

• Be sure to use the correct

tire changing only.

sent are in a secure place

front and rear jacking posi-

away from the road and from

Follow jacking instructions to reduce

tions on the vehicle; never use

the vehicle to be raised with

the possibility of personal injury.

the bumpers or any other part

the jack.

of the vehicle for jack support.

(Continued)

6 21

In case of an emergency

WARNING - Changing a tire

• To prevent vehicle movement

while changing a tire, always

set the parking brake fully, and

always block the wheel diago-

nally opposite the wheel being

changed.

• It is recommended that the

wheels of the vehicle be

chocked, and that no person

should remain in a vehicle that

1VQA4022

1VQA4023

is being jacked.

Tire replacement

4. Remove the wheel lug nut wrench,

jack, jack handle, and spare tire

1. Park on a level surface and apply

from the vehicle.

the parking brake firmly.

5. Block both the front and rear of the

2. Shift the shift lever into R

wheel that is diagonally opposite

(Reverse) with manual transaxle

the jack position.

or P (Park) with automatic

transaxle.

3. Activate the hazard warning flash-

er.

6 22

In case of an emergency

WARNING - Jack location

To reduce the possibility of

injury, be sure to use only the

jack provided with the vehicle

and in the correct jack position;

never use any other part of the

vehicle for jack support.

1KMA4018

1KMA4019

6. Loosen the wheel lug nuts coun-

7. Place the jack at the front or rear

terclockwise one turn each, but do

jacking position closest to the tire

not remove any nut until the tire

you are changing. Place the jack

has been raised off the ground.

at the designated locations under

the frame. The jacking positions

are plates welded to the frame

with two tabs and a raised dot to

index with the jack.

6 23

In case of an emergency

CAUTION

Your vehicle has metric threads

on the wheel studs and nuts.

Make certain during wheel

removal that the same nuts

removed are reinstalled - or, if

replaced, that nuts with metric

threads and the same chamfer

configuration

are

used.

Installation of a non-metric

thread nut on a metric stud or

1KMA4020

1KMA4021

vice-versa will not secure the

8. Insert the jack handle into the jack

11. Once the wheel lug nuts have

wheel to the hub properly and

and turn it clockwise, raising the

been tightened, lower the vehicle

will damage the stud so that it

vehicle until the tire just clears the

fully to the ground and continue to

must be replaced.

ground. This measurement is

tighten the lug nuts until they are

Note that most lug nuts do not

approximately 30 mm (1.2 in).

fully secured. Tighten the wheel

have metric threads. Be sure to

Before removing the wheel lug

lug nuts firmly in a “star” pattern.

use extreme care in checking

nuts, make sure the vehicle is sta-

If you are unsure of the tightness

for thread style before installing

ble and that there is no chance for

of the wheel lug nuts, have them

aftermarket lug nuts or wheels.

movement or slippage.

checked at the nearest service

If in doubt, consult an

9. Remove the wheel lug nuts by

station. The specified tightening

Authorized Kia Dealer.

turning them counterclockwise,

torque is 9~11 kg•m (65-79 lb•ft,

then remove the wheel.

88-107 N•m). Improperly tight-

ened wheel lug nuts could cause

10. Mount the spare tire into position

brake pedal vibration while brak-

and install the wheel lug nuts

ing.

with the beveled edge inward.

6 24

In case of an emergency

WARNING - Wheel studs

If the studs are damaged, they

may lose their ability to retain

the wheel. This could lead to the

loss of the wheel and a collision

resulting in serious injuries.

To prevent the jack, jack handle,

wheel lug nut wrench and spare tire

from rattling while the vehicle is in

motion, store them properly.

WARNING - Inadequate

spare tire pressure

Check the inflation pressures as

soon as possible after installing

the spare tire. Adjust it to the

specified pressure, if necessary.

Refer to Section 8, Specifications.

6 25

In case of an emergency for Your Kia Sportage SUV Second Generation (2004-2010)

Related Topics

Popular Owner Manuals

Latest Owner Manuals