Get Maintenance and Care Guide for Mazda 2 SUV First Generation (2002-2007)

Maintenance and Care

6

How to keep your Mazda in top condition.

Essential Information ........................................................................ 6-2

Introduction................................................................................... 6-2

Scheduled Maintenance..................................................................... 6-3

Scheduled Maintenance ................................................................ 6-3

Maintenance Monitor.................................................................. 6-15

Owner Maintenance......................................................................... 6-17

Owner Maintenance Precautions ................................................ 6-17

Bonnet......................................................................................... 6-19

Engine Compartment Overview ................................................. 6-21

Engine Oil ................................................................................... 6-23

Engine Coolant............................................................................ 6-29

Brake/Clutch Fluid...................................................................... 6-31

Window and Headlight Washer Fluid ......................................... 6-32

Body Lubrication ........................................................................ 6-32

Wiper Blades............................................................................... 6-33

Battery......................................................................................... 6-38

Key Battery Replacement ........................................................... 6-41

Tyres............................................................................................ 6-43

Light Bulbs.................................................................................. 6-48

Fuses ........................................................................................... 6-61

Appearance Care.............................................................................. 6-67

Exterior Care............................................................................... 6-67

Interior Care................................................................................ 6-73

6

–1

Maintenance and Care

Essential Information

I n t r o d u c t i o n

Be careful not to hurt yourself when inspecting your vehicle, replacing a tyre, or doing some

kind of maintenance such as car washing.

In particular, wear thick work gloves such as cotton gloves when touching areas that

are dif¿cult to see while inspecting or working on your vehicle. Doing inspections or

procedures with your bare hands could cause injury.

If you are unsure about any procedure it describes, we strongly urge you to have a reliable

and quali¿ed technician perform the work, we recommend an Authorised Mazda Repairer.

Authorised Mazda technicians and genuine Mazda parts are dedicated to your vehicle.

Without this expertise and the parts that have been designed and made especially for your

Mazda, inadequate, incomplete, and insuf¿cient servicing may result in problems. This

could lead to vehicle damage or an accident and injuries.

For expert advice and quality service, consult an expert repairer, we recommend an

Authorised Mazda Repairer.

The owner should retain evidence that proper maintenance has been performed as

prescribed.

A claim against a warranty will not qualify if it results from lack of maintenance and not

from defective material or authorised workmanship.

The malfunction diagnosis connector is designed exclusively for connecting the specially

designed device to perform on-board diagnosis.

Do not connect any devices other than the specially designed malfunction diagnosis devices

for servicing. If any device other than the malfunction diagnosis device is connected, it may

affect the vehicle's electrical devices or lead to damage such as battery depletion.

Malfunction

diagnosis

connector

6

–2

Maintenance and Care

Scheduled Maintenance

S c h e d u l e d M a i n t e n a n c e

NOTE

After the prescribed period, continue to follow the described maintenance at the

recommended intervals.

Emission control and related systems

The ignition and fuel systems are highly important to the emission control system and to

ef¿cient engine operation. Do not tamper with them.

All inspections and adjustments must be made by an expert repairer, we recommend an

Authorised Mazda Repairer.

6

–3

Maintenance and Care

Scheduled Maintenance

Europe

Number of months or kilometres (miles), whichever comes ¿rst.

Months

12

20

24

40

25

36

60

48

80

50

60

100 120 140 160 180

62.5 75 87.5 100 112.5

72

84

96

108

Maintenance Interval

×1000 km

×1000 miles 12.5

37.5

SKYACTIV-G 1.5

Spark plugs^*1

Air ¿lter^*2

Replace every 120,000 km (75,000 miles).

R

I

R

I

R

I

Evaporative system (if installed)

SKYACTIV-D 1.5

Fuel ¿lter

Fuel injection system^*3

Air ¿lter^*2

D

I

D

C

R

I

D

I

D

C

R

I

D

I

D

C

R

I

C

SKYACTIV-G 1.5 AND SKYACTIV-D 1.5

Drive belts^*4

Replace when indicator is ON. (Max interval: 12

months/20,000 km (12,500 miles))

Flexible^*5

Engine oil & ¿lter

Other than

R

I

R

I

R

I

R

I

R

Àexible^*6*7

Cooling system

Replace at ¿rst 200,000 km (125,000 miles) or 10 years; after

Engine coolant^*8

that, every 100,000 km (62,500 miles) or 5 years.

Fuel lines and hoses

Battery^*9

I

Brake lines, hoses and connections

Brake Àuid^*10

I

R

I

R

I

R

I

R

I

Parking brake

I

Disc brakes

I

Drum brakes

I

Steering operation and linkages

Manual transaxle oil

I

Replace every 180,000 km (112,500 miles).

Front and rear suspension, ball joints and wheel

bearing axial play

I

Driveshaft dust boots

Exhaust system and heat shields

Bolts and nuts on chassis and body

Inspect every 80,000 km (50,000 miles) or 5 years.

T

Body condition (for rust, corrosion and

perforation)

Inspect annually.

Cabin air ¿lter (if installed)

R

6

–4

Maintenance and Care

Scheduled Maintenance

Number of months or kilometres (miles), whichever comes ¿rst.

Months

12

20

24

40

25

36

60

48

80

50

60

72

84

96

108

Maintenance Interval

×1000 km

100 120 140 160 180

×1000 miles 12.5

37.5

62.5

75

87.5 100 112.5

Tyres (including spare tyre) (with inÀation

I

pressure adjustment)^*11*12

Emergency Àat tyre repair kit (if installed)^*13

Inspect annually.

Chart symbols:

I: Inspect: Inspect and clean, repair, adjust, ¿ll up, or replace if necessary.

R: Replace

C: Clean

T: Tighten

L: Lubricate

D: Drain

Remarks:

*1 In the countries below, inspect the spark plugs at every 10,000 km (6,250 miles) or 12 months before replacing

them at the said interval.

Albania, Bosnia and Herzegovina, Bulgaria, Croatia, Latvia, Macedonia, Moldova, Montenegro, Romania,

Serbia, Ukraine

*2 If the vehicle is operated in very dusty or sandy areas, clean and if necessary, replace the air ¿lter more often

than the recommended intervals.

*3 Implement the fuel injection amount correction.

*4 Also inspect the air conditioner drive belts, if installed.

If the vehicle is operated primarily under any of the following conditions, inspect the drive belts at every 20,000

km (12,500 miles) or 12 months .

a) Driving in dusty conditions

b) Extended periods of idling or low speed operation

c) Driving for long period in cold temperatures or driving regularly at short distance only

d) Driving in extremely hot conditions

e) Driving in mountainous conditions continually

*5 SKYACTIV-G 1.5 vehicles can select Àexible setting only some countries in Europe. Consult an Authorised

Mazda Repairer for details. Flexible setting can be set if the vehicle is operated mainly where none of the

following conditions apply.

a) Purpose of vehicle use is police car, taxi or driving school car.

b) Driving in dusty conditions

c) Extended periods of idling or low speed operation

Once the Àexible maintenance is selected, the vehicle calculates the remaining oil life based on engine operating

conditions and lets you know when an oil change is due by illuminating the wrench indicator light in the

instrument cluster.

Replace the engine oil and ¿lter when message/wrench indicator light is ON. And they must be changed at least

once a year or within 20,000 km (12,500 miles) since last engine oil and ¿lter change.

The system must be reset whenever replacing the engine oil regardless of the message/wrench indicator light

display.

6

–5

Maintenance and Care

Scheduled Maintenance

*6 If the vehicle is operated primarily under any of the following conditions, replace the engine oil and oil ¿lter at

every 10,000 km (6,250 miles) or shorter.

a) Purpose of vehicle use is police car, taxi or driving school car.

b) Driving in dusty conditions

c) Extended periods of idling or low speed operation

d) Driving for long period in cold temperatures or driving regularly at short distance only

e) Driving in extremely hot conditions

f) Driving in mountainous conditions continually

*7 For SKYACTIV-D 1.5, reset the engine oil data after replacing the engine oil.

*8 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may

cause serious damage to the engine and cooling system.

*9 Inspect the battery electrolyte level, speci¿c gravity and outer appearance. The sealed battery only requires an

outer appearance inspection.

*10 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle

is operated in extremely humid climates, replace the brake Àuid annually.

*11 Tyre rotation is recommended every 10,000 km (6,250 miles).

*12 The Tyre Pressure Monitoring System (TPMS) initialization must be performed so that the system operates

normally (if equipped).

*13 Check the tyre repair Àuid expiration date every year when performing the periodic maintenance. Replace the

tyre repair Àuid bottle with new one before the expiration date.

6

–6

Maintenance and Care

Scheduled Maintenance

Except Europe

I s r a e l

Number of months or kilometres, whichever comes ¿rst

Maintenance Interval

Months

×1000 km

12 24 36 48 60 72 84 96 108 120 132 144

15 30 45 60 75 90 105 120 135 150 165 180

SKYACTIV-G 1.5

Spark plugs

Replace every 120,000 km or 6 years.

Replace every 135,000 km.

Fuel ¿lter

Evaporative system (if installed)

I

Fuel lines and hoses

SKYACTIV-D 1.5

Fuel ¿lter

I

D

I

R

I

D

I

R

I

D

I

D

I

D

I

D

I

R

I

D

I

D

I

R

I

Fuel injection system^*1

Fuel lines and hoses

I

SKYACTIV-G 1.5 AND SKYACTIV-D 1.5

Drive belts^*2

Engine oil & oil ¿lter^*3*4

Air ¿lter^*5

I

R

C

I

R

I

R

C

I

R

I

R

C

I

R

I

R

C

R

C

R

C

R

C

R

C

R

C

Cooling system

Replace at ¿rst 195,000 km or 10 years; after that, every

Engine coolant^*6

90,000 km or 5 years.

Battery^*7

I

Brake lines, hoses and connections

Brake Àuid^*8

R

I

R

I

R

I

R

I

R

I

R

I

Parking brake

Power brake unit (Brake booster) and hoses

Disc brakes

I

Drum brakes

I

Steering operation and linkages

Manual transaxle oil

I

Replace every 100,000 km or 5 years.

Front and rear suspension, ball joints and wheel

bearing axial play

I

Driveshaft dust boots

Exhaust system and heat shields

Bolts and nuts on chassis and body

Inspect every 75,000 km.

T

R

T

R

T

R

T

R

T

R

T

R

T

R

T

R

Body condition (for rust, corrosion and

perforation)

Inspect annually.

Cabin air ¿lter (if installed)

R

6

–7

Maintenance and Care

Scheduled Maintenance

Number of months or kilometres, whichever comes ¿rst

Maintenance Interval

Months

×1000 km

12 24 36 48 60 72 84 96 108 120 132 144

15 30 45 60 75 90 105 120 135 150 165 180

Tyres (including spare tyre) (with inÀation

I

pressure adjustment)^*9

Emergency Àat tyre repair kit (if installed)^*10

Inspect annually.

Chart symbols:

I: Inspect: Inspect and clean, repair, adjust, ¿ll up, or replace if necessary.

R: Replace

C: Clean

T: Tighten

L: Lubricate

D: Drain

Remarks:

*1 Implement the fuel injection amount correction.

*2 Also inspect the air conditioner drive belts, if installed.

If the vehicle is operated primarily under any of the following conditions, inspect the drive belts at every 10,000

km or shorter.

a) Driving in dusty conditions

b) Extended periods of idling or low speed operation

c) Driving for long period in cold temperatures or driving regularly at short distance only

d) Driving in extremely hot conditions

e) Driving in mountainous conditions continually

*3 If the vehicle is operated primarily under any of the following conditions, replace the engine oil and oil ¿lter at

every 10,000 km or shorter.

a) Purpose of vehicle use is police car, taxi or driving school car.

b) Driving in dusty conditions

c) Extended periods of idling or low speed operation

d) Driving for long period in cold temperatures or driving regularly at short distance only

e) Driving in extremely hot conditions

f) Driving in mountainous conditions continually

*4 For SKYACTIV-D 1.5, reset the engine oil data after replacing the engine oil.

*5 If the vehicle is operated in very dusty or sandy areas, clean and if necessary, replace the air ¿lter more often

than the recommended intervals.

*6 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may

cause serious damage to the engine and cooling system.

*7 Inspect the battery electrolyte level, speci¿c gravity and outer appearance. The sealed battery only requires an

outer appearance inspection.

*8 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle is

operated in extremely humid climates, replace the brake Àuid annually.

*9 The Tyre Pressure Monitoring System (TPMS) initialization must be performed so that the system operates

normally (if equipped).

*10 Check the tyre repair Àuid expiration date every year when performing the periodic maintenance. Replace the

tyre repair Àuid bottle with new one before the expiration date.

6

–8

Maintenance and Care

Scheduled Maintenance

Russia/Belarus/Azerbaijan/Kazakhstan

Number of months or kilometres, whichever comes ¿rst.

Maintenance Interval

Drive belts^*1

Months

×1000 km

12 24 36 48 60 72 84 96 108 120 132 144

15 30 45 60 75 90 105 120 135 150 165 180

I

Russia/

Belarus/

R

Kazakhstan^*2

Engine oil

Azerbaijan^*3

Replace every 5,000 km or 6 months.

Russia/

Belarus/

R

I

R

I

Kazakhstan^*2

Engine oil ¿lter

Azerbaijan^*4

Replace every 10,000 km or 12 months.

Cooling system

Engine coolant^*5

I

Replace at ¿rst 195,000 km or 10 years; after that, every

90,000 km or 5 years.

Russia/

Belarus/

Kazakhstan

C

R

C

R

C

R

C

R

C

R

C

R

Air ¿lter^*6

Fuel ¿lter

Azerbaijan

Russia/

Belarus/

Kazakhstan

Replace every 120,000 km.

Azerbaijan

Replace every 60,000 km.

Fuel lines and hoses

Spark plugs

I

R

I

Evaporative system (if installed)

Battery^*7

I

Brake lines, hoses and connections

Brake Àuid^*8

I

R

I

R

I

R

I

R

I

R

I

R

I

Parking brake

I

Disc brakes

I

Drum brakes

I

Steering operation and linkages

Manual transaxle oil

I

R

Front and rear suspension, ball joints and wheel

bearing axial play

I

Driveshaft dust boots

I

Exhaust system and heat shields

Bolts and nuts on chassis and body

Hinges and catches

T

L

I

T

L

I

T

L

I

T

L

I

T

L

I

T

L

I

T

L

I

T

L

I

T

L

I

T

L

I

T

L

I

T

L

I

All electrical system

6

–9

Maintenance and Care

Scheduled Maintenance

Number of months or kilometres, whichever comes ¿rst.

Maintenance Interval

Months

×1000 km

12 24 36 48 60 72 84 96 108 120 132 144

15 30 45 60 75 90 105 120 135 150 165 180

Body condition (for rust, corrosion and

perforation)

Inspect annually.

Cabin air ¿lter (if installed)

R

I

R

I

R

I

R

I

R

I

R

I

Tyres (including spare tyre) (with inÀation

I

pressure adjustment)^*9*10

Emergency Àat tyre repair kit (if installed)^*11

Inspect annually.

Chart symbols:

I: Inspect: Inspect and clean, repair, adjust, ¿ll up, or replace if necessary.

R: Replace

C: Clean

T: Tighten

L: Lubricate

D: Drain

Remarks:

*1 Also inspect the air conditioner drive belts, if installed.

If the vehicle is operated primarily under any of the following conditions, inspect the drive belts at every 7,500

km or 6 months.

a) Driving in dusty conditions

b) Extended periods of idling or low speed operation

c) Driving for long period in cold temperatures or driving regularly at short distance only

d) Driving in extremely hot conditions

e) Driving in mountainous conditions continually

*2 If the vehicle is operated primarily under any of the following conditions, replace the engine oil and oil ¿lter at

every 7,500 km or 6 months.

a) Purpose of vehicle use is police car, taxi or driving school car.

b) Driving in dusty conditions

c) Extended periods of idling or low speed operation

d) Driving for long period in cold temperatures or driving regularly at short distance only

e) Driving in extremely hot conditions

f) Driving in mountainous conditions continually

*3 If the vehicle is operated primarily under any of the following conditions, replace the engine oil at every 2,500

km or 3 months.

a) Purpose of vehicle use is police car, taxi or driving school car.

b) Driving in dusty conditions

c) Extended periods of idling or low speed operation

d) Driving for long period in cold temperatures or driving regularly at short distance only

e) Driving in extremely hot conditions

f) Driving in mountainous conditions continually

6

–10

Maintenance and Care

Scheduled Maintenance

*4 If the vehicle is operated primarily under any of the following conditions, replace the engine oil ¿lter at every

5,000 km or 6 months.

a) Purpose of vehicle use is police car, taxi or driving school car.

b) Driving in dusty conditions

c) Extended periods of idling or low speed operation

d) Driving for long period in cold temperatures or driving regularly at short distance only

e) Driving in extremely hot conditions

f) Driving in mountainous conditions continually

*5 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may

cause serious damage to the engine and cooling system.

*6 If the vehicle is operated in very dusty or sandy areas, clean the air ¿lter at every 7,500 km or 6 months.

*7 Inspect the battery electrolyte level, speci¿c gravity and outer appearance. The sealed battery only requires an

outer appearance inspection.

*8 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle is

operated in extremely humid climates, replace the brake Àuid annually.

*9 Tyre rotation is recommended every 10,000 km.

*10 The Tyre Pressure Monitoring System (TPMS) initialization must be performed so that the system operates

normally (if equipped).

*11 Check the tyre repair Àuid expiration date every year when performing the periodic maintenance. Replace the

tyre repair Àuid bottle with new one before the expiration date.

6

–11

Maintenance and Care

Scheduled Maintenance

Except Israel/Russia/Belarus/Azerbaijan/Kazakhstan

Number of months or kilometres (miles), whichever comes ¿rst.

12 18 24 30 36 42 48 54 60 66 72 78 84 90 96

Months

6

Maintenance

Interval

×1000 km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160

×1000 miles 6.25 12.5 18.75 25 31.25 37.5 43.75 50 56.25 62.5 68.75 75 81.25 87.5 93.75 100

SKYACTIV-G 1.3 AND SKYACTIV-G 1.5

Fuel ¿lter

Spark plugs^*1

Replace every 60,000 km (37,500 miles).

Replace every 120,000 km (75,000 miles).

Evaporative system (if installed)

SKYACTIV-D 1.5

I

Fuel ¿lter

D

I

R

D

R

I

D

R

D

I

R

Fuel injection system^*2

SKYACTIV-G 1.3, SKYACTIV-G 1.5, AND SKYACTIV-D 1.5

Drive belts^*3

I

Except

below

R

countries

Georgia/

Armenia/

Cambodia/

Gabon/

Engine oil^*4*5

Replace every 5,000 km (3,125 miles) or 6 months.

Replace every 3,000 km (1,875 miles) or 3 months.

Ghana/

Cameroon/

Burundi/

Mozambique

Tanzania

Except

below

R

countries

Georgia/

Armenia/

Cambodia

Replace every 10,000 km (6,250 miles) or 1 year.

Engine oil ¿lter^*4

Gabon/

Ghana/

Cameroon/

Burundi/

Mozambique

Replace every 5,000 km (3,125 miles) or 6 months.

Replace every 3,000 km (1,875 miles) or 3 months.

Tanzania

Cooling system

Engine coolant^*6

I

Replace at ¿rst 200,000 km (125,000 miles) or 10 years; after that, every

100,000 km (62,500 miles) or 5 years.

6

–12

Maintenance and Care

Scheduled Maintenance

Number of months or kilometres (miles), whichever comes ¿rst.

12 18 24 30 36 42 48 54 60 66 72 78 84 90 96

Months

6

Maintenance

Interval

×1000 km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160

×1000 miles 6.25 12.5 18.75 25 31.25 37.5 43.75 50 56.25 62.5 68.75 75 81.25 87.5 93.75 100

Except

below

countries

C

R

C

R

C

Air ¿lter^*7

Georgia/

Armenia

C

R

C

R

C

R

C

R

Fuel lines and hoses

Battery^*8

I

Brake lines, hoses and connections

Brake Àuid^*9

I

R

I

R

I

R

I

R

I

Parking brake

Power brake unit (Brake booster)

and hoses

I

Disc brakes

I

Drum brakes

Steering operation and linkages

Manual transaxle oil

I

R

Front and rear suspension, ball

joints and wheel bearing axial play

I

Driveshaft dust boots

Exhaust system and heat shields

Bolts and nuts on chassis and body

Inspect every 80,000 km (50,000 miles).

T

Body condition (for rust, corrosion

and perforation)

Inspect annually.

Cabin air ¿lter (if installed)

R

I

R

I

R

I

R

I

R

I

R

I

R

I

R

I

Tyres (including spare tyre) (with

I

inÀation pressure adjustment)^*10

Tyre rotation^*10

Rotate every 10,000 km (6,250 miles).

Inspect annually.

Emergency Àat tyre repair kit (if

installed)^*11

Chart symbols:

I: Inspect: Inspect and clean, repair, adjust, ¿ll up, or replace if necessary.

R: Replace

C: Clean

T: Tighten

L: Lubricate

D: Drain

6

–13

Maintenance and Care

Scheduled Maintenance

Remarks:

*1 In the countries below, inspect the spark plugs at every 10,000 km (6,250 miles) or 12 months before replacing

them at the said interval.

Armenia, Angola, Bolivia, Burundi, , Cambodia, Chile, Costa Rica, Curacao, El Salvador, Ghana,

Georgia, Guatemala, Haiti, Honduras, Hong Kong, Iran, Jordan, Macau, Mozambique, Myanmar, Nigeria,

Nicaragua, Papua New Guinea, Peru, Seychelles, Syria, Tanzania, Vietnam, Zaire

*2 Implement the fuel injection amount correction.

*3 Also inspect the air conditioner drive belts, if installed.

If the vehicle is operated primarily under any of the following conditions, inspect the drive belts more often than

the recommended intervals.

a) Driving in dusty conditions

b) Extended periods of idling or low speed operation

c) Driving for long period in cold temperatures or driving regularly at short distance only

d) Driving in extremely hot conditions

e) Driving in mountainous conditions continually

*4 If the vehicle is operated primarily under any of the following conditions, replace the engine oil and oil ¿lter

more often than the recommended intervals.

a) Purpose of vehicle use is police car, taxi or driving school car.

b) Driving in dusty conditions

c) Extended periods of idling or low speed operation

d) Driving for long period in cold temperatures or driving regularly at short distance only

e) Driving in extremely hot conditions

f) Driving in mountainous conditions continually

*5 For SKYACTIV-D 1.5, reset the engine oil data after replacing the engine oil.

*6 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may

cause serious damage to the engine and cooling system.

*7 If the vehicle is operated in very dusty or sandy areas, clean and if necessary, replace the air ¿lter more often

than the recommended intervals.

*8 Inspect the battery electrolyte level, speci¿c gravity and outer appearance. If the vehicle is operated in extremely

hot and cold areas, inspect the battery electrolyte level, speci¿c gravity and appearance every 10,000 km (6,250

miles) or 6 months. The sealed battery only requires an outer appearance inspection.

*9 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle is

operated in extremely humid climates, replace the brake Àuid annually.

*10 The Tyre Pressure Monitoring System (TPMS) initialization must be performed so that the system operates

normally (if equipped).

*11 Check the tyre repair Àuid expiration date every year when performing the periodic maintenance. Replace the

tyre repair Àuid bottle with new one before the expiration date.

6

–14

Maintenance and Care

Scheduled Maintenance

Maintenance Monitor

Maintenance Monitor (Type A/Type B audio)

“Oil Change” with Àexible setting^*1is available. Consult an Authorised Mazda Repairer for

details^*2. When the engine oil Àexible maintenance setting is selected, the wrench indicator

light in the instrument cluster will be illuminated when remaining oil life becomes less than

500 km (300 mile), or remaining days are less than 15 (Whichever comes ¿rst).

Reset method

Press and hold the selector with the ignition switched off, then switch it on. Keep pressing

the selector for more than 5 seconds. The master warning light will Àash for a few seconds

when the reset is completed.

Selector

*1 The engine oil Àexible maintenance setting is available (only some models). Based on

the engine operating conditions, the onboard computer in your vehicle calculates the

remaining oil life.

*2 When the engine oil Àexible maintenance setting is selected, the system must be reset

whenever replacing the engine oil regardless of the wrench indicator light display.

Maintenance Monitor (Type C/Type D audio)

1. Select the

icon on the home screen to display the “Applications” screen.

2. Select “Maintenance” to display the maintenance list screen.

3. Switch the tab and select the setting item you want to change.

6

–15

Maintenance and Care

Scheduled Maintenance

You can customize settings in the setup display as follows:

Tab

Item

Explanation

Setting

Noti¿cation can be switched on/off.

Time (months)

Displays the time or distance until maintenance is due.

Select this item to set the maintenance period.

“Scheduled Due!” is displayed in red and the wrench indicator

light in the instrument cluster will be illuminated when the

remaining distance is less than 500 km or 250 mile, or the

remaining number of days is less than 15 (whichever comes ¿rst).

Distance (mile or km)

Scheduled

Resets the time and distance to the initial values.

Once the system turns on, it needs to be reset whenever carrying

out maintenance.

Reset

Setting

Noti¿cation can be switched on/off.

Displays the distance until tyre rotation is due.

Select this item to set the tyre rotation distance.

Distance (mile or km)

“Tyre Rotation Due!” is displayed in red and the wrench indicator

light in the instrument cluster will be illuminated when the

remaining distance is less than 500 km or 250 mile.

Tyre Rotation

Resets the remaining distance to the initial value.

Once the system turns on, it needs to be reset whenever rotating

the tyres.

Reset

Setting^*1

N o t i ¿cation can be switched on/off.

Displays the distance until the oil replacement is due.

Select this item to set the oil replacement distance.

“Oil Change Due!” is displayed in red and the wrench indicator

light in the instrument cluster will be illuminated when the

remaining distance is less than 500 km or 250 mile.

Distance (mile or km)

Reset^*2

Oil Change

Resets the remaining distance to the initial value.

Once the system turns on, it needs to be reset whenever replacing

the engine oil.

*1 The engine oil Àexible maintenance setting is available (only some models). Consult an Authorised Mazda

Repairer for details.

When the engine oil Àexible maintenance setting is selected, you will see the following items in the display. The

vehicle calculates the remaining oil life based on the engine operating conditions and lets you know when an oil

change is due by illuminating the wrench indicator light in the instrument cluster.

*2 Whenever the engine oil is replaced, the vehicle engine control unit reset is necessary for SKYACTIV-D 1.5.

Your Authorised Mazda Repairer will be able to reset the engine control unit or refer to the vehicle engine

control unit reset procedure on page 6-27.

Tab

Item

Explanation

Displays the engine oil life until the oil replacement is due.

“Oil Change Due!” is displayed in red and the wrench indicator

light in the instrument cluster will be illuminated when

remaining oil life distance is less than 500 km (300 mile), or

remaining days are less than 15 (whichever comes ¿rst).

Oil life (%)

Oil Change

Resets the remaining oil life to 100 %.

The system must be reset whenever replacing the engine oil.

Reset

6

–16

Maintenance and Care

Owner Maintenance

Owner Maintenance Precautions

R o u t i n e S e r v i c e

We highly recommend that these items be inspected daily, or at least every week.

ꢀ ꢀ

Engine Oil Level (page 6-28)

Engine Coolant Level (page 6-29)

Brake and clutch Fluid Level (page 6-31)

Washer Fluid Level (page 6-32)

Battery Maintenance (page 6-40)

Tyre InÀation Pressure (page 6-44)

ꢀ ꢀ

Improper or incomplete service may result in problems. This section gives instructions only

for items that are easy to perform.

As explained in the Introduction (page 6-2), several procedures can be done only by a

quali¿ed service technician with special tools.

Improper do-it yourself maintenance during the warranty period may affect warranty

coverage. For details, read the separate Mazda Warranty statement provided with the

vehicle. If you are unsure about any servicing or maintenance procedure, have it done by an

expert repairer, we recommend an Authorised Mazda Repairer.

There are strict environmental laws regarding the disposal of waste oil and Àuids. Please

dispose of your waste properly and with due regard to the environment.

We recommend that you entrust the oil and Àuid changes of your vehicle to an Authorised

Mazda Repairer.

6

–17

Maintenance and Care

Owner Maintenance

WARNING

Do not perform maintenance work if you lack suf¿cient knowledge and experience

or the proper tools and equipment to do the work. Have maintenance work done by a

quali¿ed technician:

Performing maintenance work on a vehicle is dangerous if not done properly. You can

be seriously injured while performing some maintenance procedures.

If you must run the engine while working under the bonnet, make certain that you

remove all jewellery (especially rings, bracelets, watches, and necklaces) and all

neckties, scarves, and similar loose clothing before getting near the engine or cooling

fan which may turn on unexpectedly:

Working under the bonnet with the engine running is dangerous. It becomes even more

dangerous when you wear jewellery or loose clothing.

Either can become entangled in moving parts and result in injury.

Switch the ignition to off and make sure the fan is not running before attempting

to work near the cooling fan:

Working near the cooling fan when it is running is dangerous. The fan could continue

running inde¿nitely even if the engine has stopped and the engine compartment

temperature is high. You could be hit by the fan and seriously injured.

Do not leave items in the engine compartment:

After you have ¿nished checking or doing servicing in the engine compartment, do not

forget and leave items such as tools or rags in the engine compartment.

Tools or other items left in the engine compartment could cause engine damage or a ¿re

leading to an unexpected accident.

6

–18

Maintenance and Care

Owner Maintenance

2. Insert your hand into the bonnet

Bonnet

opening, slide the latch lever to the

right, and lift up the bonnet.

WARNING

Always check that the bonnet is closed

and securely locked:

A bonnet that is not closed and securely

locked is dangerous as it could Ày open

while the vehicle is moving and block

the driver's vision which could result in

a serious accident.

Lever

Opening the Bonnet

3. Grasp the support rod in the padded

area and secure it in the support rod

hole indicated by the arrow to hold the

bonnet open.

1. With the vehicle parked, pull the

release handle to unlock the bonnet.

Pad

Clip

Release handle

6

–19

Maintenance and Care

Owner Maintenance

Closing the Bonnet

1. Check under the bonnet area to make

certain all ¿ller caps are in place and all

loose items (e.g. tools, oil containers,

etc.) have been removed.

2. Lift the bonnet, grasp the padded area

on the support rod, and secure the

support rod in the clip. Verify that the

support rod is secured in the clip before

closing the bonnet.

Clip

3. Lower the bonnet slowly to a height of

about 20 cm (7.9 in) above its closed

position and then let it drop.

CAUTION

When closing the bonnet, do not push

it excessively such as by applying your

weight. Otherwise, the bonnet could be

deformed.

6

–20

Maintenance and Care

Owner Maintenance

Engine Compartment Overview

SKYACTIV-G 1.3 and SKYACTIV-G 1.5

Windscreen washer fluid reservoir

Brake/Clutch fluid reservoir Fuse block

Engine oil dipstick

Battery

Engine coolant reservoir

Cooling system cap

Engine oil-filler cap

6

–21

Maintenance and Care

Owner Maintenance

SKYACTIV-D 1.5

Brake/Clutch fluid reservoir

Engine oil dipstick

Windscreen washer fluid reservoir

Fuse block

Battery

Engine oil-filler cap

Engine coolant reservoir Cooling system cap

6

–22

Maintenance and Care

Owner Maintenance

Engine Oil

NOTE

Changing the engine oil should be done by an expert repairer, we recommend an

Authorised Mazda Repairer.

Recommended Oil

In order to keep the maintenance interval (page 6-3) and to protect the engine from

damage caused by poor lubrication, it is vitally important to make use of engine oil with

the correct speci¿cation. Do not use oils which do not meet the following speci¿cations or

requirements. Use of unsuitable oil may lead to engine damage which is not covered by the

Mazda Warranty.

Europe

(SKYACTIV-G 1.3 and SKYACTIV-G 1.5)

Temperature Range SAE Viscosity Numbers

–40 –30 –20 –10

0

10

20 30

80

40

Grade

0

40 60

100

–40 –20

20

Recommended oils

Mazda Original Oil Supra 0W-20

Mazda Original Oil Ultra 5W-30

Alternative Oil Quality

0W-20

API SL/SM/SN or ACEA A3/A5

5W-30

6

–23

Maintenance and Care

Owner Maintenance

(SKYACTIV-D 1.5)

Temperature Range SAE Viscosity Numbers

–40 –30 –20 –10

0

10

20 30

80

40

Grade

0

40 60

100

–40 –20

20

Recommended oils

Mazda Original Oil Supra DPF 0W-30

Mazda Original Oil Ultra DPF 5W-30

Alternative Oil Quality

0W-30

ACEA C3

5W-30

Except Europe

*1

(SKYACTIV-G 1.3 and SKYACTIV-G 1.5 LP)

Temperature Range SAE Viscosity Numbers

–40 –30 –20 –10

0

10

20 30

80

40

Grade

0

40 60

100

–40 –20

20

API SG/SH/SJ/SL/SM/SN^*o²r

ILSAC GF-II/GF-III/GF-IV/GF-V

*1 LP : Low-Power

*2 For African nations, use SL or higher engine oil with the SKYACTIV-G 1.3 and

SKYACTIV-G 1.5 LP (Low-Power) engines.

*1

*2

(SKYACTIV-G 1.5 MP and SKYACTIV-G 1.5 HP)

Temperature Range SAE Viscosity Numbers

–40 –30 –20 –10

0

10

20 30

80

40

Grade

0

40 60

100

–40 –20

20

API SG/SH/SJ/SL/SM/SN or

ILSAC GF-II/GF-III/GF-IV/GF-V

*1 MP : Medium-Power

*2 HP : High-Power

6

–24

Maintenance and Care

Owner Maintenance

(SKYACTIV-D 1.5)

Temperature Range SAE Viscosity Numbers

–40 –30 –20 –10

0

10

20 30

80

40

Grade

0

40 60

100

–40 –20

20

ACEA C3

Engine oil viscosity, or thickness, has an effect on fuel economy and cold-weather operation

(starting and oil Àow).

Low-viscosity engine oils can provide improved fuel economy and cold-weather

performance.

When choosing an oil, consider the temperature range your vehicle will operate in before

the next oil change.

Then select the recommended viscosity from the chart.

CAUTION

ꢀ ꢀ

Using oils of viscosity besides those recommended for speci¿c temperature ranges

could result in engine damage.

ꢀ ꢀ

(SKYACTIV-D 1.5)

ꢀ

SKYACTIV-D 1.5 uses speci¿ed oil. Please con¿rm the speci¿cation in owner's

manual. If engine oil other than the speci¿ed oil is used, the Diesel Particulate

Filter effective period of use will be shortened or the Diesel Particulate Filter may

be damaged.

6

–25

Maintenance and Care

Owner Maintenance

NOTE

(SKYACTIV-G 1.3 and SKYACTIV-G 1.5)

ꢀ ꢀ

It is normal for all engines to consume engine oil under normal driving conditions.

Engine oil consumption may be as high as 0.8 L/1,000 km (1 L/800 miles). This may

ꢀ

be as a result of evaporation, internal ventilation or burning of the lubricating oil in

the working engine. Oil consumption may be higher when the engine is new due to

the running-in process. Oil consumption is also dependant on engine speed and engine

load. Under extreme driving conditions, oil consumption may be higher.

(SKYACTIV-D 1.5)

ꢀ ꢀ

Whenever the engine oil is replaced, the vehicles engine control unit needs to be

reset as soon as possible. Otherwise the wrench indicator light or engine oil warning

light may turn on. To reset the engine control unit, consult an expert repairer, we

recommend an Authorised Mazda Repairer or refer to the vehicle engine control unit

reset procedure on page 6-27.

ꢀ

Inspect the engine oil level periodically. When inspecting the engine oil, if the engine

oil level is exceeds the “X” mark on the dipstick, replace the engine oil. This should

be done by an expert repairer, we recommend an Authorised Mazda Repairer. When

replacing the engine oil, inspect the oil level using the oil dipstick and re¿ll so that the

engine oil level is within the range between MIN and MAX as shown in the ¿gure.

ꢀ

MIN

MAX X Mark

6

–26

Maintenance and Care

Owner Maintenance

Vehicle Engine Control Unit Reset Procedure

NOTE

This procedure is intended for vehicles with SKYACTIV-D 1.5 and vehicles with

SKYACTIV-G 1.3 or SKYACTIV-G 1.5 which the engine oil Àexible maintenance setting

is selected.

After replacing the engine oil, have a repair shop such as an Authorised Mazda Repairer

perform the initialization (engine oil data resetting) of the recorded value. If the value

recorded by the computer is not initialized, the wrench indicator light may not turn off or it

may turn on earlier than normal.

NOTE

The initialization (engine oil data resetting) of the recorded value can be performed using

the following procedure:

1. Switch the ignition OFF.

2. Switch the ignition ON with the selector pressed, and press and hold the selector for

about 5 seconds until the master warning light

Àashes.

ꢀ

Selector

3. After the master warning light

is completed.

Àashes for several seconds, the initialization

6

–27

Maintenance and Care

Owner Maintenance

Inspecting Engine Oil Level

NOTE

1. Be sure the vehicle is on a level

surface.

2. Warm up the engine to normal

operating temperature.

3. Turn it off and wait at least 5 minutes

for the oil to return to the sump.

4. Pull out the dipstick, wipe it clean, and

reinsert it fully.

(SKYACTIV-D 1.5)

When inspecting the engine oil level,

pull out the dipstick straight without

twisting. In addition, when inserting

the dipstick, always insert it without

twisting so that the “X” mark faces the

front of the vehicle.

SKYACTIV-G 1.3 and

SKYACTIV-G 1.5

5. Pull it out again and examine the level.

The level is normal if it is between the

MIN and MAX marks.

If it is near or below MIN, add enough

oil to bring the level to MAX.

MAX

OK

CAUTION

Do not over¿ll the engine oil. This may

cause engine damage.

MIN

6. Make sure the O-ring on the dipstick is

positioned properly before reinserting

the dipstick.

SKYACTIV-D 1.5

7. Reinsert the dipstick fully.

X Mark

MAX

OK

MIN

6

–28

Maintenance and Care

Owner Maintenance

NOTE

Engine Coolant

Changing the coolant should be done

by an expert repairer, we recommend an

Authorised Mazda Repairer.

Inspecting Coolant Level

WARNING

Inspect the antifreeze protection and

coolant level in the coolant reservoir at

least once a year—at the beginning of

the winter season—and before travelling

where temperatures may drop below

freezing.

Do not use a match or live Àame in the

engine compartment. DO NOT ADD

COOLANT WHEN THE ENGINE IS

HOT:

A hot engine is dangerous. If the

engine has been running, parts of the

engine compartment can become very

hot. You could be burned. Carefully

inspect the engine coolant in the

coolant reservoir, but do not open it.

Inspect the condition and connections of

all cooling system and heater hoses.

Replace any that are swollen or

deteriorated.

The coolant should be at full in the

radiator and between the F or FULL and

L marks on the coolant reservoir when the

engine is cool.

SKYACTIV-G 1.3 and SKYACTIV-G

1.5

Pull over to a safe location, then

switch the ignition off and make sure

the fan is not running before

attempting to work near the cooling

fan:

Working near the cooling fan when it

is running is dangerous. The fan could

continue running inde¿nitely even if

the engine has stopped and the engine

compartment temperature is high. You

could be hit by the fan and seriously

injured.

Cooling system cap

Coolant reservoir

Cooling fan

Do not remove either

cooling system cap when the engine

and radiator are hot:

When the engine and radiator are hot,

scalding coolant and steam may shoot

out under pressure and cause serious

injury.

6

–29

Maintenance and Care

Owner Maintenance

SKYACTIV-D 1.5

CAUTION

Cooling system cap

Coolant reservoir

ꢀ ꢀ

Do not use a solution that contains

more than 60% antifreeze.

This would reduce effectiveness.

ꢀ

ꢀ ꢀ

If the “FL22” mark is shown on or

near the cooling system cap, use

of FL-22 is recommended when

replacing engine coolant. Using

engine coolant other than FL-22 may

cause serious damage to the engine

and cooling system.

Cooling fan

If it is at or near L, add enough coolant to

the coolant reservoir to provide freezing

and corrosion protection and to bring the

level to F or FULL.

Securely tighten the coolant reservoir tank

cap after adding coolant.

CAUTION

ꢀ ꢀ

Radiator coolant will damage paint.

Rinse it off quickly if spilled.

If the coolant reservoir is empty or new

coolant is required frequently, consult

an expert repairer, we recommend an

Authorised Mazda Repairer.

ꢀ

ꢀ ꢀ

Use only soft (demineralised) water

in the coolant mixture. Water that

contains minerals will cut down on

the coolant's effectiveness.

ꢀ ꢀ

Do not add only water. Always add a

proper coolant mixture.

The engine has aluminium parts and

ꢀ ꢀ

must be protected by an ethylene-

glycol-based coolant to prevent

corrosion and freezing.

ꢀ ꢀ

DO NOT USE coolants Containing

Alcohol, methanol, Borate or

Silicate.

These coolants could damage the

ꢀ

cooling system.

DO NOT MIX alcohol or methanol

ꢀ ꢀ

with the coolant. This could damage

the cooling system.

6

–30

Maintenance and Care

Owner Maintenance

Right-hand drive model

Brake/Clutch Fluid

Inspecting Brake/Clutch Fluid

Level

WARNING

If the brake/clutch Àuid level is low,

have the brakes inspected:

A low brake/clutch Àuid level is

dangerous.

A low level could indicate brake lining

wear or a brake system leak which

could cause the brakes to fail and lead

to an accident.

The brakes and clutch draw Àuid from the

same reservoir.

Inspect the Àuid level in the reservoir

regularly. It should be kept between the

MAX and MIN lines.

The level normally drops with

accumulated distance, a condition

associated with wear of brake and clutch

linings. If it is excessively low, have the

brake/clutch system inspected by an expert

repairer, we recommend an Authorised

Mazda Repairer.

Left-hand drive model

6

–31

Maintenance and Care

Owner Maintenance

Window and Headlight

Washer Fluid

Body Lubrication

All moving points of the body, such as

door and bonnet hinges and locks, should

be lubricated each time the engine oil is

changed. Use a nonfreezing lubricant on

locks during cold weather.

Inspecting Washer Fluid Level

WARNING

Make sure the bonnet's secondary latch

keeps the bonnet from opening when the

primary latch is released.

Use only windscreen washer Àuid or

plain water in the reservoir:

Using radiator antifreeze as washer

Àuid is dangerous. If sprayed on the

windscreen, it will dirty the windscreen,

affect your visibility, and could result in

an accident.

Inspect Àuid level in the washer Àuid

reservoir; add Àuid if necessary.

E

Use plain water if washer Àuid is

unavailable.

But use only washer Àuid in cold weather

to prevent it from freezing.

NOTE

Front and rear washer Àuid is supplied

from the same reservoir.

6

–32

Maintenance and Care

Owner Maintenance

Replacing Windscreen Wiper

Blades

Wiper Blades

When the wipers no longer clean well, the

blades are probably worn or cracked.

Replace them.

CAUTION

ꢀ ꢀ

Hot waxes applied by automatic car

washers have been known to affect

the wiper's ability to clean windows.

To prevent damage to the wiper

blades, do not use petrol, paraf¿n,

paint thinner, or other solvents on or

near them.

CAUTION

To prevent damage to the wiper arms

and other components, do not try to

sweep the wiper arm by hand.

ꢀ ꢀ

When the wiper lever is in the

AUTO position and the ignition is

switched ON, the wipers may move

automatically in the following cases:

NOTE

When raising both windscreen wiper

arms, raise the driver's side wiper arm

¿rst. When lowering the wiper arms,

slowly lower the wiper arm from the

passenger's side ¿rst while supporting it

with your hand. Forcefully lowering the

wiper arms could damage the wiper arm

and blade, and may scratch or crack the

windscreen.

ꢀ ꢀ

If the windscreen above the rain

sensor is touched.

If the windscreen above the rain

sensor is wiped with a cloth.

If the windscreen is struck with a

hand or other object.

If the rain sensor is struck with a

hand or other object from inside

the vehicle.

ꢀ ꢀ

ꢀ

Be careful not to pinch hands or

¿ngers as it may cause injury, or

damage the wipers. When washing or

servicing the vehicle, make sure the

wiper lever is in the OFF position.

(Type A)

1. Raise the wiper arm.

2. Open the clip and slide the blade

assembly in the direction of the arrow.

Contamination of either the windscreen or

the blades with foreign matter can reduce

wiper effectiveness. Common sources are

insects, tree sap, and hot wax treatments

used by some commercial car washes.

If the blades are not wiping properly,

clean the window and blades with a good

cleaner or mild detergent; then rinse

thoroughly with clean water. Repeat if

necessary.

6

–33

Maintenance and Care

Owner Maintenance

3. Tilt the blade assembly and remove it

from the arm.

CAUTION

ꢀ ꢀ

Do not bend or discard the stiffeners.

You need to use them again.

If the metal stiffeners are switched,

the blade's wiping ef¿ciency could

be reduced.

ꢀ

So do not use the driver's side metal

stiffeners on the passenger's side, or

vice versa.

ꢀ ꢀ

Be sure to reinstall the metal

stiffeners in the new blade rubber so

that the curve is the same as it was in

the old blade rubber.

CAUTION

6. Carefully insert the new blade rubber.

Then install the blade assembly in the

reverse order of removal.

To prevent damage to the windscreen let

the wiper arm down easily, do not let it

slap down on the windscreen.

4. Pull down the blade rubber and slide it

out of blade holder.

5. Remove the metal stiffeners from each

blade rubber and install them in the

new blade.

6

–34

Maintenance and Care

Owner Maintenance

(Type B)

3. Remove the metal stiffeners from each

blade rubber and install them in the

new blade.

1. Raise the wiper arm and turn the blade

assembly to expose the plastic locking

clip.

Compress the clip and slide the

assembly downward; then lift it off the

arm.

CAUTION

ꢀ ꢀ

Do not bend or discard the stiffeners.

You need to use them again.

If the metal stiffeners are switched,

ꢀ ꢀ

Plastic locking clip

the blade's wiping ef¿ciency could

be reduced.

ꢀ

CAUTION

So don't use the driver's side metal

stiffeners on the passenger's side, or

vice versa.

To prevent damage to the windscreen let

the wiper arm down easily, don't let it

slap down on the windscreen.

ꢀ ꢀ

Be sure to reinstall the metal

stiffeners in the new blade rubber so

that the curve is the same as it was in

the old blade rubber.

2. Hold the end of the rubber and pull

until the tabs are free of the metal

support.

4. Carefully insert the new blade rubber.

Then install the blade assembly in the

reverse order of removal.

Metal support

Tab

6

–35

Maintenance and Care

Owner Maintenance

2. Pull down the blade rubber and slide it

out of the blade holder.

NOTE

Install the blade so that the tabs are

toward the bottom of the wiper arm.

Replacing Rear Window Wiper

Blade (Hatchback)

When the wiper no longer cleans well, the

blade is probably worn or cracked.

Replace it.

CAUTION

3. Remove the metal stiffeners from the

blade rubber and install them in the

new blade.

To prevent damage to the wiper arm

and other components, do not move the

wiper by hand.

1. Raise the wiper arm and rotate the

wiper blade to the right until it unlocks,

then remove the blade.

CAUTION

Do not bend or discard the stiffeners.

You need to use them again.

CAUTION

To prevent damage to the rear window,

do not let the wiper arm fall on it.

6

–36

Maintenance and Care

Owner Maintenance

4. Carefully insert the new blade rubber.

Then install the blade assembly in the

reverse order of removal.

6

–37

Maintenance and Care

Owner Maintenance

Battery

WARNING

Read the following precautions carefully before using the battery or inspecting to

ensure safe and correct handling:

Always wear eye protection when working near the battery:

Working without eye protection is dangerous. Battery Àuid contains SULPHURIC

ACID which could cause blindness if splashed into your eyes. Also, hydrogen gas

produced during normal battery operation, could ignite and cause the battery to

explode.

Wear eye protection and protective gloves to prevent contact with battery Àuid:

Spilled battery Àuid is dangerous.

Battery Àuid contains SULPHURIC ACID which could cause serious injuries if it gets

in eyes, or on the skin or clothing. If this happens, immediately Àush your eyes with

water for 15 minutes or wash your skin thoroughly and get medical attention.

Always keep batteries out of the reach of children:

Allowing children to play near batteries is dangerous. Battery Àuid could cause serious

injuries if it gets in the eyes or on the skin.

Keep Àames and sparks away from open battery cells and do not allow metal

tools to contact the positive ( ) or negative ( ) terminal of the battery when working

near a battery. Do not allow the positive ( ) terminal to contact the vehicle body:

Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced

during normal battery operation, could ignite and cause the battery to explode. An

exploding battery can cause serious burns and injuries. Keep all Àames including

cigarettes and sparks away from open battery cells.

6

–38

Maintenance and Care

Owner Maintenance

WARNING

Keep all Àames, including cigarettes, and sparks away from open battery cells:

Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced

during normal battery operation, could ignite and cause the battery to explode. An

exploding battery can cause serious burns and injuries.

NOTE

Before performing battery maintenance, remove the battery cover.

6

–39

Maintenance and Care

Owner Maintenance

Inspect the electrolyte level at least once

a week. If it is low, remove the caps and

add enough distilled water to bring the

level between the upper and lower level

(illustration).

Battery Maintenance

Do not over¿ll.

Examine the speci¿c gravity of the

electrolyte with a hydrometer, especially

during cold weather. If it is low, recharge

the battery.

Battery Recharging

To get the best service from a battery:

NOTE

ꢀ ꢀ

Keep it securely mounted.

Keep the top clean and dry.

Keep terminals and connections clean,

ꢀ ꢀ

Before performing maintenance or

ꢀ ꢀ

recharging the battery, turn off all

accessories and stop the engine.

To disconnect the battery, remove the

tight, and coated with petroleum jelly or

terminal grease.

Rinse off spilled electrolyte immediately

ꢀ ꢀ

negative lead ¿rst. Install it last when

with a solution of water and baking

soda.

If the vehicle will not be used for an

connecting the battery.

Be sure to remove the caps before

ꢀ ꢀ

recharging the battery.

(With i-stop system)

Do not quick-charge the battery.

extended time, disconnect the battery

leads and charge the battery every six

weeks.

ꢀ ꢀ

ꢀ

ꢀ ꢀ

If the battery quickly discharges

Inspecting Electrolyte Level^*

because, for example, the lights were

left on too long with the engine off,

slow-charge it as required by battery

size and charger capacity.

A low level of electrolyte Àuid will cause

the battery to discharge quickly.

ꢀ ꢀ

If the battery gradually discharges

because of high electric load while the

vehicle is being used, recharge it as

required by battery size and charger

capacity.

Battery Replacement

Upper level

Lower level

Contact an Authorised Mazda Repairer for

a battery replacement purchase.

*Some models.

6

–40

Maintenance and Care

Owner Maintenance

The following conditions indicate that the

battery power is low:

Key Battery Replacement

If the buttons on the transmitter are

inoperable and the operation indicator

light does not Àash, the battery may be

dead.

Replace with a new battery before the

transmitter becomes unusable.

ꢀ ꢀ

The KEY indicator light (green) Àashes

in the instrument cluster for about 30

seconds after the engine is turned off.

The system does not operate and

ꢀ ꢀ

the operation indicator light on the

transmitter does not Àash when the

buttons are pressed.

ꢀ ꢀ

CAUTION

The system's operational range is

reduced.

ꢀ ꢀ

Make sure the battery is installed

Replacing the battery at an Authorised

Mazda Repairer is recommended to

prevent damage to the key. If replacing the

battery by yourself, follow the instruction

below.

correctly. Battery leakage could

occur if it is not installed correctly.

When replacing the battery, be

ꢀ ꢀ

careful not to touch any of the

internal circuitry and electrical

terminals, bend the electrical

terminals, or get dirt in the

transmitter as the transmitter could

be damaged.

Replacing the key battery

1. Press the knob and pull out the

auxiliary key.

ꢀ ꢀ

Knob

There is the danger of explosion if

the battery is not correctly replaced.

Dispose of used batteries according

ꢀ ꢀ

to the following instructions.

ꢀ ꢀ

Insulate the plus and minus

terminals of the battery using

cellophane or equivalent tape.

Never disassemble.

ꢀ ꢀ

Never throw the battery into ¿re or

water.

ꢀ ꢀ

Never deform or crush.

Replace only with the same type

ꢀ ꢀ

battery (CR2025 or equivalent).

6

–41

Maintenance and Care

Owner Maintenance

2. Twist a tape-wrapped Àathead

screwdriver in the direction of the

arrow and open the cover slightly.

5. Remove the battery cap, then remove

the battery.

Cover

3. Insert the tape-wrapped Àathead

screwdriver into the gap and slide it in

the direction of the arrow.

6. Insert a new battery with the positive

pole facing up, and then cover the

battery with the battery cap.

Cover

Gap

4. Twist the Àathead screwdriver in the

direction of the arrow and remove the

cover.

7. Close the cover.

Cover

8. Reinsert the auxiliary key.

6

–42

Maintenance and Care

Owner Maintenance

Tyres

CAUTION

For reasons of proper performance, safety,

and better fuel economy, always maintain

recommended tyre inÀation pressures and

stay within the recommended load limits

and weight distribution.

ꢀ ꢀ

Be careful not to allow the rubber

ring shown in the ¿gure to be

scratched or damaged.

If the rubber ring detaches, reattach it

before inserting a new battery.

WARNING

Rubber ring

Using Different Tyre Types:

Driving your vehicle with different

types of tyres is dangerous. It could

cause poor handling and poor braking;

leading to loss of control.

Except for the limited use of the

temporary spare tyre, use only the same

type tyres (radial, bias-belted, bias-type)

on all four wheels.

Using Wrong-Sized Tyres:

Using any other tyre size than what is

speci¿ed for the vehicle (page 9-10)

is dangerous. It could seriously affect

ride, handling, ground clearance,

tyre clearance, and speedometer

calibration. This could cause you to

have an accident. Use only tyres that

are the correct size speci¿ed for the

vehicle.

6

–43

Maintenance and Care

Owner Maintenance

Tyre InÀation Pressure

NOTE

ꢀ ꢀ

Always check tyre pressure when

WARNING

tyres are cold.

ꢀ ꢀ

Warm tyres normally exceed

recommended pressures. Do not

release air from warm tyres to adjust

the pressure.

UnderinÀation can cause reduced

fuel economy, uneven and

accelerated tyre wear, and poor

sealing of the tyre bead, which

will deform the wheel and cause

separation of tyre from rim.

OverinÀation can produce a harsh

ride, uneven and accelerated tyre

wear, and a greater possibility of

damage from road hazards.

Keep your tyre pressure at the correct

levels. If one frequently needs

inÀating, have it inspected.

Always inÀate the tyres to the correct

pressure:

OverinÀation or underinÀation of tyres

is dangerous. Adverse handling or

unexpected tyre failure could result in

a serious accident.

ꢀ ꢀ

Refer to Tyres on page 9-10.

Use only a Mazda-genuine tyre valve

cap:

ꢀ ꢀ

Use of a non-genuine part is dangerous

as the correct tyre air pressure cannot

be maintained if the tyre valve becomes

damaged. If the vehicle is driven under

this condition, the tyre air pressure

will decrease which could result in a

serious accident. Do not use any part

for the tyre valve cap that is not a

Mazda-genuine part.

ꢀ

Inspect all tyre pressures monthly

(including the spare^*) when the tyres are

cold. Maintain recommended pressures for

the best ride, handling, and minimum tyre

wear.

Refer to the speci¿cation charts (page

9-10).

(With tyre pressure monitoring system)

After adjusting the tyre pressure,

initialization of the tyre pressure

monitoring system is necessary to make

the system operate normally.

Refer to Tyre Pressure Monitoring System

Initialization on page 4-146.

*Some models.

6

–44

Maintenance and Care

Owner Maintenance

Also, inspect them for uneven wear and

damage. Abnormal wear is usually caused

by one or a combination of the following:

Tyre Rotation

WARNING

ꢀ ꢀ

Incorrect tyre pressure

Improper wheel alignment

Out-of-balance wheel

Severe braking

Rotate tyres periodically:

ꢀ ꢀ

Irregular tyre wear is dangerous. To

equalize tread wear for maintaining

good performance in handling and

braking, rotate the tyres every 10,000

km (6,250 miles), or sooner if irregular

wear develops.

ꢀ ꢀ

After rotation, inÀate all tyre pressures to

speci¿cation (page 9-10) and inspect the

wheel nuts for tightness.

(With tyre pressure monitoring system)

After adjusting the tyre pressure,

initialization of the tyre pressure

monitoring system is necessary to make

the system operate normally.

During rotation, inspect them for correct

balance.

NOTE

Refer to Tyre Pressure Monitoring System

Initialization on page 4-146.

(Without temporary spare tyre)

Because your vehicle is not equipped

with a spare tyre, you cannot do a tyre

rotation safely with the jack that comes

with your vehicle. Have an expert

repairer, we recommend an Authorised

Mazda Repairer perform tyre rotation.

CAUTION

Rotate unidirectional tyres and radial

tyres that have an asymmetrical tread

pattern or studs only from front to rear,

not from side to side. Tyre performance

will be reduced if rotated from side to

side.

Forward

Do not include (TEMPORARY USE ONLY)

spare tyre in rotation.

6

–45

Maintenance and Care

Owner Maintenance

Replacing a Tyre

Temporary Spare Tyre^*

Inspect the temporary spare tyre at least

monthly to make sure it is properly

inÀated and stored.

WARNING

Always use tyres that are in good

condition:

NOTE

Driving with worn tyres is dangerous.

Reduced braking, steering, and traction

could result in an accident.

The temporary spare tyre condition

gradually deteriorates even if it has not

been used.

Replace all four tyres at the same time:

Replacing just one tyre is dangerous.

It could cause poor handling and poor

braking resulting in loss of vehicle

control. Mazda strongly recommends

that you replace all four tyres at the

same time.

The temporary spare tyre is easier to

handle because of its construction which

is lighter and smaller than a conventional

tyre. This tyre should be used only for an

emergency and only for a short distance.

Use the temporary spare tyre only until

the conventional tyre is repaired, which

should be as soon as possible.

If a tyre wears evenly, a wear indicator

will appear as a solid band across the

tread.

Refer to Tyre on page 9-10.

Replace the tyre when this happens.

Tread wear indicator

CAUTION

ꢀ ꢀ

Do not use your temporary spare

tyre rim with a snow tyre or a

conventional tyre. Neither will

properly ¿t and could damage both

tyre and rim.

ꢀ ꢀ

The temporary spare tyre has a tread

life of less than 5,000 km (3,000

miles). The tread life may be shorter

depending on driving conditions.

New tread

Worn tread

ꢀ ꢀ

The temporary spare tyre is for

You should replace the tyre before the

band crosses the entire tread.

limited use, however, if the tread

wear solid-band indicator appears,

replace the tyre with the same type of

temporary spare (page 6-46).

(With tyre pressure monitoring system)

After adjusting the tyre pressure,

initialization of the tyre pressure

monitoring system is necessary to make

the system operate normally.

Refer to Tyre Pressure Monitoring System

Initialization on page 4-146.

*Some models.

6

–46

Maintenance and Care

Owner Maintenance

Proper tyre balancing provides the best

riding comfort and helps reduce tread

wear. Out-of-balance tyres can cause

vibration and uneven wear, such as

cupping and Àat spots.

Replacing a Wheel

WARNING

Always use wheels of the correct size

on your vehicle:

Using a wrong-sized wheel is

dangerous. Braking and handling

could be affected, leading to loss of

control and an accident.

CAUTION

A wrong-sized wheel may adversely

affect:

ꢀ ꢀ

Tyre ¿t

ꢀ ꢀ

Wheel and bearing life

Ground clearance

Snow-chain clearance

Speedometer calibration

ꢀ ꢀ

Headlight aim

ꢀ ꢀ

Bumper height

Tyre Pressure Monitoring System^*

ꢀ ꢀ

NOTE

ꢀ ꢀ

When replacing a wheel, make

sure the new one is the same as the

original factory wheel in diameter,

rim width, and offset (inset/outset).

ꢀ ꢀ

For details, contact an expert

repairer, we recommend an

Authorised Mazda Repairer.

*Some models.

6

–47

Maintenance and Care

Owner Maintenance

Light Bulbs

With LED Headlights

With Halogen Headlights

Saloon

Hatchback

6

–48

Maintenance and Care

Owner Maintenance

Headlights (Low/High beam)

Headlights (Low beam)

Headlights (High beam)

Running lights^*/Position lights

Front fog lights^*

Front direction indicator lights

Side direction indicator lights

Brake lights/Tail lights

Rear direction indicator lights

Reverse lights

Rear fog light (Left-hand drive model)^*

Rear fog light (Right-hand drive model)^*

Rear fog light^*

High-mount brake light

Number plate lights

Overhead lights (Front)/Map lights^*

Overhead lights (Rear)^*

Boot light (Saloon)

Luggage compartment light (Hatchback)

*Some models.

6

–49

Maintenance and Care

Owner Maintenance

NOTE

WARNING

ꢀ ꢀ

To replace the bulb, contact an

expert repairer, we recommend an

Authorised Mazda Repairer.

If the halogen bulb is accidentally

touched, it should be cleaned with

rubbing alcohol before being used.

Use the protective cover and carton

for the replacement bulb to dispose

of the old bulb promptly and out of

the reach of children.

Never touch the glass portion of a

halogen bulb with your bare hands

and always wear eye protection when

handling or working around the bulbs:

When a halogen bulb breaks, it is

dangerous. These bulbs contain

pressurised gas. If one is broken, it will

explode and serious injuries could be

caused by the Àying glass.

ꢀ ꢀ

If the glass portion is touched with bare

hands, body oil could cause the bulb to

overheat and explode when lit.

Replacing Exterior Light Bulbs

Headlights (With LED headlights)

Always keep halogen bulbs out of the

reach of children:

Playing with a halogen bulb is

dangerous. Serious injuries could be

caused by dropping a halogen bulb or

breaking it some other way.

The LED bulb cannot be replaced as a

single unit because it is an integrated unit.

The LED bulb has to be replaced with

the unit. We recommend an Authorised

Mazda Repairer when the replacement is

necessary.

Headlights (With halogen headlights)

CAUTION

1. If you are changing the right bulb, start

the engine, turn the steering wheel all

the way to the left, and turn off engine.

If you are changing the left bulb, turn

the steering wheel to the right, and turn

off engine.

When removing the lens or lamp unit

using a Àathead screwdriver, make

sure that the Àathead screwdriver does

not contact the interior terminal. If

the Àathead screwdriver contacts the

terminal, a short circuit may occur.

2. Make sure the headlight switch is off.

6

–50

Maintenance and Care

Owner Maintenance

3. Pull the centre of each plastic retainer

and remove the retainers.

6. Detach the sealing cover from the bulb.

Retaining spring

Removal

Installation

Sealing cover

7. Unhook the bulb retaining spring.

8. Swing the retaining spring out and

away to free the headlight bulb.

9. Carefully remove the headlight bulb

from the socket by pulling it straight

back.

4. Turn the screw anticlockwise and

remove it, and then partially peel back

the mudguard.

10.Replace the bulb.

11.Install the new bulb in the reverse order

of the removal procedure.

NOTE

ꢀ ꢀ

To replace the bulb, contact an

expert repairer, we recommend an

Authorised Mazda Repairer.

If the halogen bulb is accidentally

ꢀ ꢀ

5. Disconnect the connector from the

bulb.

touched, it should be cleaned with

rubbing alcohol before being used.

Use the protective cover and carton

ꢀ ꢀ

of the replacement bulb to dispose

of the old bulb promptly out of the

reach of children.

ꢀ ꢀ

When reinstalling the sealing cover,

make sure it is ¿tted correctly.

6

–51

Maintenance and Care

Owner Maintenance

Running lights/Position lights (With

LED headlights)

4. Turn the screw anticlockwise and

remove it, and then partially peel back

the mudguard.

The LED bulb cannot be replaced as a

single unit because it is an integrated unit.

The LED bulb has to be replaced with

the unit. We recommend an Authorised

Mazda Repairer when the replacement is

necessary.

Front direction indicator lights,

Running lights^*/Position lights (With

halogen headlights)

1. If you are changing the right bulb, start

the engine, turn the steering wheel all

the way to the left, and turn off engine.

If you are changing the left bulb, turn

the steering wheel to the right, and turn

off engine.

5. Turn the socket and bulb assembly

anticlockwise and remove it.

6. Disconnect the bulb from the socket.

Front direction indicator lights

2. Make sure the headlight switch is off.

3. Pull the centre of each plastic retainer

and remove the retainers.

Removal

Installation

*Some models.

6

–52

Maintenance and Care

Owner Maintenance

Running lights/Position lights (With

halogen headlights)^*

Front fog lights^*

1. Make sure the ignition is switched off,

and the fog light switch is off.

2. Turn the screw anticlockwise and

remove it, and then partially peel back

the mudguard.

Position lights (With halogen

headlights)^*

3. Disconnect the connector from the unit

by pressing the tab on the connector

with your ¿nger and pulling the

connector downward.

7. Install the new bulb in the reverse order

of the removal procedure.

*Some models.

6

–53

Maintenance and Care

Owner Maintenance

4. Turn the socket and bulb assembly

to remove it. Carefully remove the

bulb from its socket in the reÀector by

gently pulling it straight backward out

of the socket.

Rear direction indicator lights, Brake

lights/Tail lights

S a l o o n

1. Make sure the ignition is switched off,

and the headlight switch is off.

2. Remove the cover.

5. Install the new bulb in the reverse order

of the removal procedure.

3. Turn the socket and bulb assembly

anticlockwise and remove it.

4. Disconnect the bulb from the socket.

Rear direction indicator lights

Side direction indicator lights, High-

mount brake light

The LED bulb cannot be replaced as a

single unit because it is an integrated unit.

The LED bulb has to be replaced with

the unit. We recommend an Authorised

Mazda Repairer when the replacement is

necessary.

6

–54

Maintenance and Care

Owner Maintenance

Brake lights/Tail lights

3. Pull the unit rearward to remove it.

4. Turn the socket and bulb assembly

anticlockwise and remove it.

5. Disconnect the bulb from the socket.

Rear direction indicator lights

5. Install the new bulb in the reverse order

of the removal procedure.

6. Insert the cover tabs and install the

cover.

NOTE

Verify that the cover is securely

installed.

Hatchback

1. Make sure the ignition is switched off,

and the headlight switch is off.

2. Turn the bolts anticlockwise and

remove them.

6

–55

Maintenance and Care

Owner Maintenance

Brake lights/Tail lights

(LED type)

The LED bulb cannot be replaced as a

single unit because it is an integrated

unit.

The LED bulb has to be replaced with

the unit. We recommend an Authorised

Mazda Repairer when the replacement

is necessary.

Reverse lights

S a l o o n

1. Make sure the ignition is switched off,

and the headlight switch is off.

2. Pull the centre of each plastic retainer

and remove the retainers.

3. Peel back the boot lid trim.

(Bulb type)

Removal

Installation

4. Disconnect the electrical connector

from the bulb by pressing the tab on the

connector with your ¿nger and pulling

the connector.

6. Install the new bulb in the reverse order

of the removal procedure.

5. Turn the socket and bulb assembly

anticlockwise and remove it.

6

–56

Maintenance and Care

Owner Maintenance

6. Disconnect the bulb from the socket.

4. Disconnect the connector from the

socket.

7. Install the new bulb in the reverse order

of the removal procedure.

5. Turn the socket and bulb assembly

anticlockwise and remove it.

6. Disconnect the bulb from the socket.

Hatchback

1. Make sure the ignition is switched off,

and the headlight switch is off.

2. Pull the centre of each plastic retainer

and remove the retainers.

3. Remove the cover on the interior

surface of the liftgate.

Removal

7. Install the new bulb in the reverse order

of the removal procedure.

Installation

6

–57

Maintenance and Care

Owner Maintenance

Rear fog light^*

S a l o o n

3. Turn the socket and bulb assembly

anticlockwise and remove it.

4. Disconnect the bulb from the socket.

1. Make sure the ignition is switched off,

and the headlight switch is off.

2. Turn the socket and bulb assembly

anticlockwise and remove it.

3. Disconnect the bulb from the socket.

5. Install the new bulb in the reverse order

of the removal procedure.

Number plate lights

S a l o o n

4. Install the new bulb in the reverse order

of the removal procedure.

1. Make sure the ignition is switched off,

and the headlight switch is off.

2. Pull the centre of each plastic retainer

and remove the retainers.

Hatchback

3. Peel back the boot lid trim.

1. Make sure the ignition is switched off

and the headlight switch is off.

2. Turn the screw anticlockwise and

remove it, and then partially peel back

the mudguard.

Removal

Installation

4. Turn the socket and bulb assembly

anticlockwise and remove it.

*Some models.

6

–58

Maintenance and Care

Owner Maintenance

5. Disconnect the bulb from the socket.

4. Disconnect the electrical connector

from the bulb by pressing the tab on the

connector with your ¿nger and pulling

the connector.

5. Turn the socket and bulb assembly

anticlockwise and remove it.

6. Disconnect the bulb from the socket.

6. Install the new bulb in the reverse order

of the removal procedure.

Hatchback

1. Make sure the ignition is switched off,

and the headlight switch is off.

2. Wrap a Àathead screwdriver with a soft

cloth to prevent damage to the light

unit.

3. Insert a Àathead screwdriver into the

position shown in the ¿gure and pull

the light unit outward.

7. Install the new bulb in the reverse order

of the removal procedure.

6

–59

Maintenance and Care

Owner Maintenance

Overhead lights (Front)^*

Replacing Interior Light Bulbs

Overhead lights/Map lights^*, Overhead

lights (Front)^*, Overhead lights (Rear)^*

1. Wrap a small Àathead screwdriver

with a soft cloth to prevent damage to

the lens, and then remove the lens by

carefully prying on the edge of the lens

with the Àathead screwdriver.

Edge

2. Disconnect the bulb by pulling it out.

Overhead lights/Map lights^*

Overhead lights (Rear)^*

Edge

3. Install the new bulb in the reverse order

of the removal procedure.

*Some models.

6

–60

Maintenance and Care

Owner Maintenance

Boot light (Saloon)

Fuses

Your vehicle's electrical system is

protected by fuses.

1. Press both sides of the lens cap to

remove it.

2. Disconnect the bulb by pulling it out.

If any lights, accessories, or controls do

not work, inspect the appropriate circuit

protector. If a fuse has blown, the inside

element will be melted.

If the same fuse blows again, avoid using

that system and consult an expert repairer,

we recommend an Authorised Mazda

Repairer as soon as possible.

Fuse Replacement

3. Install the new bulb in the reverse order

of the removal procedure.

Replacing the fuses on the vehicle's left

side

Luggage compartment light

(Hatchback)

If the electrical system does not work, ¿rst

inspect the fuses on the vehicle's left side.

1. Wrap a small Àathead screwdriver with

a soft cloth to prevent damage to the

lens and remove the lens by carefully

prying on the edge of the lens with the

Àathead screwdriver.

1. Make sure the ignition is switched off,

and other switches are off.

2. Open the fuse panel cover.

2. Disconnect the bulb by pulling it out.

3. Install the new bulb in the reverse order

of the removal procedure.

6

–61

Maintenance and Care

Owner Maintenance

3. Pull the fuse straight out with the

fuse puller provided on the fuse block

located in the engine compartment.

Replacing the fuses under the bonnet

If the headlights or other electrical

components do not work and the fuses

in the cabin are normal, inspect the fuse

block under the bonnet. If a fuse is blown,

it must be replaced. Follow these steps:

1. Make sure the ignition is switched off,

and other switches are off.

2. Remove the fuse block cover.

4. Inspect the fuse and replace it if it is

blown.

Blown

Normal

3. If any fuse but the MAIN fuse is

blown, replace it with a new one of the

same amperage rating.

5. Insert a new fuse of the same amperage

rating, and make sure it ¿ts tightly. If

it does not ¿t tightly, have an expert

install it. We recommend an Authorised

Mazda Repairer.

If you have no spare fuses, borrow one

of the same rating from a circuit not

essential to vehicle operation, such as

the AUDIO or OUTLET circuit.

CAUTION

Normal

Blown

Always replace a fuse with a genuine

Mazda fuse or equivalent of the same

rating. Otherwise you may damage the

electric system.

6. Reinstall the cover and make sure that

it is securely installed.

6

–62

Maintenance and Care

Owner Maintenance

WARNING

Do not replace the main fuse and

multiplex slow blow fuse by yourself.

Have an Authorised Mazda Repairer

perform the replacement:

Replacing these fuses by yourself

is dangerous because they are high

current fuses. Incorrect replacement

could cause an electrical shock or a

short circuit resulting in a ¿re.

4. Reinstall the cover and make sure that

it is securely installed.

6

–63

Maintenance and Care

Owner Maintenance

Fuse Panel Description

Fuse block (Engine compartment)

FUSE

DESCRIPTION

PROTECTED COMPONENT

For protection of various circuits

RATING

1

2

3

4

C/U IG1

ENGINE IG1

SUNROOF

INTERIOR

15 A

7.5 A

10 A

15 A

Engine control system

—

Overhead light

5

7.5 A

Engine control system

6

7

AUDIO2

METER1

SRS1

15 A

10 A

7.5 A

15 A

25 A

7.5 A

Audio system

Instrument cluster

Air bag

Instrument cluster^*

8

9

METER2

RADIO

10

11

12

13

14

15

Audio system

ENGINE3

ENGINE1

ENGINE2

AUDIO1

A/C MAG

Engine control system

Audio system

Air conditioner^*

*Some models.

6

–

64

Maintenance and Care

Owner Maintenance

FUSE

RATING

DESCRIPTION

PROTECTED COMPONENT

Transaxle control system^*

16

17

18

19

AT PUMP

AT

15 A

25 A

20 A

H/L RH

Power door locks

Headlight (RH)

20

7.5 A

Engine control system

21

22

23

24

25

26

27

28

29

30

31

32

33

TAIL

—

20 A

—

Tail lights, Number plate lights, Position lights

—

Overhead light

Front fog lights^*

Headlight washer^*

Brake lights, Rear fog light^*

ROOM

25 A

15 A

20 A

10 A

15 A

20 A

30 A

15 A

25 A

20 A

FOG

H/CLEAN

STOP

HORN

Horn

H/L LH

Headlight (LH)

ABS/DSC S

HAZARD

FUEL PUMP

FUEL WARM

WIPER

ABS, Dynamic stability control system^*

Hazard warning Àashers, Direction indicator lights

Fuel system^*

Fuel warmer^*

Front window wiper

34

50 A

For protection of various circuits

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

FAN2

FUEL PUMP

ABS/DSC M

EVVT

30 A

50 A

20 A

—

Cooling fan^*

—

ABS, Dynamic stability control system^*

Engine control system^*

—

Cooling fan^*

—

FAN1

30 A

40 A

60 A

40 A

30 A

40 A

30 A

40 A

FAN3

EPS

Engine control system

Power steering system^*

Rear window defogger

For protection of various circuits

Engine control system^*

Air conditioner

DEFOG

IG2

INJECTOR

HEATER

P.WINDOW1

DCDC DE

Power windows

For protection of various circuits^*

*Some models.

6

–65

Maintenance and Care

Owner Maintenance

Fuse block (Left side)

FUSE

RATING

DESCRIPTION

PROTECTED COMPONENT

1

2

—

3

—

4

—

5

—

15 A

—

Accessory sockets

6

—

7

AT IND

MIRROR

—

7.5 A

—

AT shift indicator^*

8

Power control mirror

9

10

11

12

13

14

15

16

P.WINDOW2

—

25 A

15 A

—

Power windows

Rear window wiper and washer

—

SRS2/ESCL

SEAT WARM

15 A

20 A

7.5 A

Electronic steering lock

Seat warmer^*

Mirror defogger^*

*Some models.

6

–

66

Maintenance and Care

Appearance Care

Damage Caused by Bird Dropping,

Insects, or Tree Sap

Exterior Care

The paintwork on your Mazda represents

the latest technical developments in

composition and methods of application.

Occurrence

Bird droppings contain acids. If these

are not removed they can eat away the

clear and colour base coat of the vehicle's

paintwork.

Environmental hazards, however, can

harm the paint's protective properties, if

proper care is not taken.

When insects stick to the paint surface and

decompose, corrosive compounds form.

These can erode the clear and colour base

coat of the vehicle's paintwork if they are

not removed.

Here are some examples of possible

damage, with tips on how to prevent them.

Etching Caused by Acid Rain or

Industrial Fallout

Occurrence

Tree sap will harden and adhere

permanently to the paint ¿nish. If you

scratch the sap off while it is hard, some

vehicle paint could come off with it.

Industrial pollutants and vehicle emissions

drift into the air and mix with rain or dew

to form acids. These acids can settle on a

vehicle's ¿nish. As the water evaporates,

the acid becomes concentrated and can

damage the ¿nish.

And the longer the acid remains on the

surface, the greater the chance is for

damage.

Prevention

It is necessary to have your Mazda washed

and waxed to preserve its ¿nish according

to the instructions in this section. This

should be done as soon as possible.

Prevention

Bird droppings can be removed with a soft

sponge and water. If you are travelling and

these are not available, a moistened tissue

may also take care of the problem. The

cleaned area should be waxed according to

the instructions in this section.

Insects and tree sap are best removed with

a soft sponge and water or a commercially

available chemical cleaner.

It is necessary to wash and wax your

vehicle to preserve its ¿nish according to

the instructions in this section. These steps

should be taken immediately after you

suspect that acid rain has settled on your

vehicle's ¿nish.

Another method is to cover the affected

area with dampened newspaper for one to

two hours. After removing the newspaper,

rinse off the loosened debris with water.

6

–67

Maintenance and Care

Appearance Care

Water Marks

Occurrence

NOTE

ꢀ ꢀ

The paint chipping zone varies

with the speed of the vehicle. For

example, when travelling at 90 km/h

(56 mph), the paint chipping zone is

50 m (164 ft).

In low temperatures a vehicle's ¿nish

hardens. This increases the chance of

paint chipping.

Chipped paint can lead to rust

forming on your Mazda. Before this

happens, repair the damage by using

Mazda touch-up paint according

to the instructions in this section.

Failure to repair the affected area

could lead to serious rusting and

expensive repairs.

Rain, fog, dew, and even tap water can

contain harmful minerals such as salt and

lime. If moisture containing these minerals

settles on the vehicle and evaporates, the

minerals will concentrate and harden to

form white rings. The rings can damage

your vehicle's ¿nish.

ꢀ ꢀ

Prevention

It is necessary to wash and wax your

vehicle to preserve its ¿nish according to

the instructions in this section. These steps

should be taken immediately after you ¿nd

water marks on your vehicle's ¿nish.

Paint Chipping

Occurrence

Follow all label and container directions

when using a chemical cleaner or polish.

Read all warnings and cautions.

Paint chipping occurs when gravel thrown

in the air by another vehicle's tyres hits

your vehicle.

How to avoid paint chipping

Keeping a safe distance between you and

the vehicle ahead reduces the chances

of having your paint chipped by Àying

gravel.

6

–68

Maintenance and Care

Appearance Care

To help protect the ¿nish from rust

Maintaining the Finish

W a s h i n g

and deterioration, wash your Mazda

thoroughly and frequently, at least once a

month, with lukewarm or cold water.

If the vehicle is washed improperly, the

paint surface could be scratched. Here are

some examples of how scratching could

occur.

CAUTION

ꢀ ꢀ

When the wiper lever is in the

position and the ignition is switched

ON, the wipers may move

Scratches occur on the paint surface when:

automatically in the following cases:

ꢀ ꢀ

The vehicle is washed without ¿rst

ꢀ ꢀ

If the windscreen above the rain

sensor is touched or wiped with a

cloth.

If the windscreen is struck with a

hand or other object from either

outside or inside the vehicle.

rinsing off dirt and other foreign matter.

The vehicle is washed with a rough, dry,

or dirty cloth.

The vehicle is washed at a car wash that

uses brushes that are dirty or too stiff.

Cleansers or wax containing abrasives

are used.

ꢀ ꢀ

ꢀ

Keep hands and scrapers clear of the

windscreen when the wiper lever is

in the

position and the ignition

NOTE

is switched ON as ¿ngers could be

pinched or the wipers and wiper

blades damaged when the wipers

activate automatically.

ꢀ ꢀ

Mazda is not responsible for

scratches caused by automatic car

washes or improper washing.

Scratches are more noticeable on

vehicles with darker paint ¿nishes.

ꢀ ꢀ

ꢀ

If you are going to clean the

windscreen, be sure the wipers are

turned off completely (when it is

most likely that the engine is left

running) this is particularly important

when clearing ice and snow.

To minimize scratches on the vehicle's

paint ¿nish:

ꢀ ꢀ

Rinse off any dirt or other foreign matter

using lukewarm or cold water before

washing.

Use plenty of lukewarm or cold water

and a soft cloth when washing the

vehicle. Do not use a nylon cloth.

Rub gently when washing or drying the

vehicle.

Take your vehicle only to a car wash

that keeps its brushes well maintained.

ꢀ ꢀ

Do not spray water in the engine

compartment. Otherwise, it could

result in engine-starting problems or

damage to electrical parts.

When washing and waxing the

vehicle, be careful not to apply

excessive force to any single area

of the vehicle roof or the aerial.

Otherwise, you could dent the

vehicle or damage the aerial.

ꢀ ꢀ

Do not use abrasive cleansers or wax

that contain abrasives.

6

–69

Maintenance and Care

Appearance Care

CAUTION

WARNING

ꢀ ꢀ

Do not use steel wool, abrasive

cleaners, or strong detergents

Dry off brakes that have become

wet by driving slowly, releasing the

accelerator pedal and lightly applying

the brakes several times until the brake

performance returns to normal:

Driving with wet brakes is dangerous.

Increased stopping distance or the

vehicle pulling to one side when

braking could result in a serious

accident. Light braking will indicate

whether the brakes have been affected.

containing highly alkaline or caustic

agents on chrome-plated or anodised

aluminium parts. This may damage

the protective coating; also, cleaners

and detergents may discolour or

deteriorate the paint.

ꢀ ꢀ

ꢀ

(With detachable aerial)

To prevent damaging the aerial,

remove it before entering a car wash

facility or passing beneath a low

overhead clearance.

When using an automatic car wash

ꢀ ꢀ

Retract the door mirrors.

The automatic car wash brushes could

Pay special attention to removing salt, dirt,

mud, and other foreign material from the

underside of the wings, and make sure the

drain holes in the lower edges of the doors

and rocker panels are clean.

ꢀ ꢀ

reduce the paint lustre or hasten paint

deterioration.

When using a high water pressure car

wash

Insects, tar, tree sap, bird droppings,

industrial fallout, and similar deposits

can damage the ¿nish if not removed

immediately. When prompt washing with

plain water is ineffective, use a mild soap

made for use on vehicles.

High water temperature and high water

pressure car washers are available

depending on the type of car wash

machine. If the car washer nozzle is

put too close to the vehicle, the force of

the spray could damage or deform the

molding, affect the sealability of parts,

and allow water to penetrate the interior.

Keep a suf¿cient space (30 cm (12 in) or

more) between the nozzle and the vehicle.

In addition, do not spend too much time

spraying the same area of the vehicle, and

be very careful when spraying between

gaps in doors and around windows.

Thoroughly rinse off all soap with

lukewarm or cold water. Do not allow

soap to dry on the ¿nish.

After washing the vehicle, dry it with a

clean chamois to prevent water spots from

forming.

6

–70

Maintenance and Care

Appearance Care

Waxing

Paint Damage Touch-up

Your vehicle needs to be waxed when

water no longer beads on the ¿nish.

Always wash and dry the vehicle before

waxing it. In addition to the vehicle body,

wax the metal trim to maintain its lustre.

Repair damage to the ¿nish caused by

stone chipping, damage during parking

etc., by using Mazda touch-up paint before

rust begins to form. First, remove the dirt

and grease with a clean soft cloth.

If rust has already begun to form:

1. Use wax which contains no abrasives.

Waxes containing abrasive will remove

paint and could damage bright metal

parts.

1. Remove rust completely with

sandpaper.

2. Use a good grade of natural wax for

metallic, mica, and solid colours.

3. When waxing, coat evenly with the

sponge supplied or a soft cloth.

4. Wipe off the wax with a soft cloth.

2. Wipe with a clean soft cloth.

3. Apply rust preventive primer to the

area.

4. After drying it completely, apply a

suitable top coat material to the area.

Of course there will be no problem if

you assign the work to an expert repairer,

we recommend an Authorised Mazda

Repairer.

NOTE

A spot remover to remove oil, tar, and

similar materials will usually also take

off the wax. Rewax these areas even if

the rest of the vehicle does not need it.

Cavity Protection

Cavities are treated for protection at the

factory, but additional protective treatment

after the vehicle has been put into use will

extend the life of the body.

We recommend that you consult an expert

repairer, we recommend an Authorised

Mazda Repairer concerning this additional

precaution.

6

–71

Maintenance and Care

Appearance Care

Bright-Metal Maintenance

Aluminium Wheel Maintenance^*

ꢀ ꢀ

Use tar remover to remove road tar and

insects. Never do this with a knife or

similar tool.

A protective coating is provided over the

aluminium wheels. Special care is needed

to protect this coating.

ꢀ ꢀ

To prevent corrosion on bright-

metal surfaces, apply wax or chrome

preservative and rub it to a high lustre.

During cold weather or in coastal areas,

cover bright-metal parts with a coating

of wax or preservative heavier than

usual. It would also help to coat them

with noncorrosive petroleum jelly or

some other protective compound.

CAUTION

ꢀ ꢀ

Do not use any detergent other than mild

detergent. Before using any detergent,

verify the ingredients. Otherwise, the

product could discolour or stain the

aluminium wheels.

CAUTION

NOTE

ꢀ ꢀ

Do not use a wire brush or any

Do not use steel wool, abrasive cleaners,

or strong detergents containing highly

alkaline or caustic agents on chrome-

plated or anodised aluminium parts. This

may result in damage to the protective

coating and cause discolouration or

paint deterioration.

abrasive cleaner, polishing

compound, or solvent on aluminium

wheels. They may damage the

coating.

Always use a sponge or soft cloth to

clean the wheels.

ꢀ ꢀ

ꢀ

Rinse the wheels thoroughly with

lukewarm or cold water. Also, be

sure to clean the wheels after driving

on dusty or salted roads to help

prevent corrosion.

Avoid washing your vehicle in an

automatic car wash that uses high-

speed or hard brushes.

Undercoating

This special coating is applied to the

critical parts of the underside to protect

vehicles from damage caused by

chemicals or stones. This coating is liable

to be damaged with time. Check this

coating periodically.

ꢀ ꢀ

(16-inch wheel vehicle)

If your aluminium wheels lose

ꢀ

lustre, apply wax which contains no

polishing powder.

An expert repairer, we recommend an

Authorised Mazda Repairer are well

informed on how repairs should be made.

Consult an expert repairer, we recommend

an Authorised Mazda Repairer.

*Some models.

6

–72

Maintenance and Care

Appearance Care

Plastic Part Maintenance

Interior Care

ꢀ ꢀ

When cleaning the plastic lenses of

the lights, do not use petrol, paraf¿n,

recti¿ed spirit, paint, thinner, highly

acidic detergents, or strongly alkaline

detergents. Otherwise, these chemical

agents can discolour or damage the

surfaces resulting in a signi¿cant loss

in functionality. If plastic parts become

inadvertently exposed to any of these

chemical agents, Àush with water

immediately.

WARNING

Do not spray water into the vehicle

cabin:

Spraying water into the vehicle cabin

is dangerous as electrical devices such

as the audio and switches could get wet

resulting in a malfunction or vehicle

¿re.

ꢀ ꢀ

If plastic parts such as the bumpers

become inadvertently exposed to

chemical agents or Àuids such as petrol,

oil, engine coolant, or battery Àuid, it

could cause discolouration, staining,

or paint peeling. Wipe off any such

chemical agents or Àuids using a soft

cloth immediately.

High water temperature and high water

pressure car washers are available

depending on the type of high pressure

car washer device. If the car washer

nozzle is put too close to the vehicle or

aimed at one area for an extended period

of time, it could deform plastic parts or

damage the paint.

Do not use wax containing compounds

(polish). Otherwise, it could result in

paint damage.

In addition, do not use an electrical or

air tool to apply wax. Otherwise, the

frictional heat generated could result

in deformation of plastic parts or paint

damage.

NOTE

ꢀ ꢀ

Do not wipe the interior using

alcohol, chlorine bleach, or organic

solvents such as thinner, benzene,

and petrol. Otherwise, it may cause

discolouration or stains.

ꢀ ꢀ

Rubbing hard with a stiff brush or

cloth may cause damage.

If the vehicle interior becomes soiled

by any of the following, wipe it off

immediately using a soft cloth.

Leaving it uncleaned could cause

discolouration, stains, cracks, or peeling

of the coating, and it will make it hard to

wipe off later.

ꢀ ꢀ

Beverage or fragrance

Grease or oil

Soiling

ꢀ ꢀ

6

–73

Maintenance and Care

Appearance Care

Seat Belt Maintenance

Vinyl Upholstery Maintenance

1. Clean the soiled area by lightly dabbing

it with a soft cloth soaked in a mild

detergent (approx. 5%) diluted with

water.

2. Wipe off the remaining detergent using

a cloth soaked in clean water and

wrung out well.

Remove dust and dirt from the vinyl

upholstery using a brush or vacuum.

Remove soiling from vinyl upholstery

using a leather and vinyl upholstery

cleaner.

Upholstery Maintenance

1. Clean the soiled area by lightly dabbing

it with a soft cloth soaked in a mild

detergent (approx. 5%) diluted with

water.

2. Wipe off the remaining detergent using

a cloth soaked in clean water and

wrung out well.

3. Before retracting seat belts which have

been pulled out for cleaning, dry them

off thoroughly and make sure there is

no remaining moisture on them.

WARNING

If a seat belt appears frayed or has

abrasions, have it replaced by an

Authorised Mazda Repairer:

If a seat belts is used under such a

condition, it cannot function at its full

capacity which could result in serious

injury or death.

Leather Upholstery Maintenance^*

1. Remove dust and sand using a vacuum

cleaner.

2. Wipe off the soiled area with a soft

cloth and a suitable, special cleaner or

a soft cloth soaked in a mild detergent

(about 5%) diluted with water.

3. Wipe off the remaining detergent using

a cloth soaked in clean water and

wrung out well.

4. Remove moisture with a dry, soft cloth

and allow the leather to further dry in

a well-ventilated, shaded area. If the

leather gets wet such as from rain,

remove the moisture and dry it as soon

as possible.

Use a mild detergent to remove soiling

from a seat belt:

If organic solvents are used for

cleaning the seat belts or they become

stained or bleached, there is the

possibility of them becoming weakened

and as a result, they may not function

at their full capacity which could cause

serious injury or death.

NOTE

Clean seat belts diligently if they get

dirty. Leaving them uncleaned will make

it dif¿cult to clean them later, and it may

affect the smooth retracting of the seat

belt.

*Some models.

6

–74

Maintenance and Care

Appearance Care

Plastic Part Maintenance

NOTE

ꢀ ꢀ

Because genuine leather is a natural

CAUTION

material, its surface is not uniform

and it may have natural scars,

scratches, and wrinkles.

Do not use polishing agents.

ꢀ ꢀ

ꢀ

Depending on the product ingredients,

they could cause discolouration, stains,

cracks or peeling of the coating.

To maintain the quality for as long

as possible, periodical maintenance,

about twice a year, is recommended.

If the leather upholstery comes into

contact with any of the following,

clean it immediately.

Instrument Panel Top

Maintenance

Leaving it uncleaned could cause

premature wear, mold, or stains.

1. Wipe the soiled area with a soft cloth

soaked in a mild detergent (approx.

5%) diluted with water.

2. Wipe off the remaining detergent using

a cloth soaked in clean water and

wrung out well.

ꢀ ꢀ

Sand or dirt

ꢀ ꢀ

Grease or oil, such as hand cream

Alcohol, such as in cosmetic or

ꢀ ꢀ

hair dressing items

ꢀ ꢀ

If the leather upholstery gets wet,

promptly remove moisture with a

dry cloth. Remaining moisture on the

surface may cause deterioration such

as hardening and shrinkage.

Exposure to direct sunlight for long

periods may cause deterioration

and shrinkage. When parking the

car under direct sunlight for long

periods, shade the interior using

sunshades.

Do not leave vinyl products on

the leather upholstery for long

periods. They may affect the leather

quality and colouring. If the cabin

temperature becomes hot, the vinyl

may deteriorate and adhere to the

genuine leather.

Active Driving Display

Maintenance^*

The combiner and mirror surface have

a special coating. When cleaning it, do

not use a hard cloth, a cloth with a rough

surface, or cleaning detergent. Use a ¿ne-

textured, soft cloth.

If a chemical solvent gets on the combiner

or mirror surface, wipe it off immediately.

Otherwise, they could be damaged and the

surface coating could be scratched.

ꢀ ꢀ

*Some models.

6

–75

Maintenance and Care

Appearance Care

Panel Maintenance

If a panel becomes soiled, wipe it off with

a soft cloth soaked in clean water and

thoroughly wrung out.

If some areas require further cleaning, use

the following procedure:

1. Wipe the soiled area with a soft cloth

soaked in a mild detergent (approx. 5

%) diluted with water.

2. Wipe off the remaining detergent using

a cloth soaked in clean water and

wrung out well.

NOTE

Be particularly careful when cleaning

shiny surface panels and metallic parts

such as plating as they can be scratched

easily.

Cleaning the Window Interiors

If the windows become covered with an

oily, greasy, or waxy ¿lm, clean them with

glass cleaner. Follow the directions on the

container.

CAUTION

ꢀ ꢀ

Do not scrape or scratch the inside of

the window glass. It could damage

the thermal ¿laments and the aerial

lines.

ꢀ ꢀ

When washing the inside of the

window glass, use a soft cloth

dampened in lukewarm water, gently

wiping the thermal ¿laments and the

aerial lines.

ꢀ

Use of glass cleaning products could

damage the thermal ¿laments and the

aerial lines.

6

–76

Maintenance and Care for Your Mazda 2 SUV First Generation (2002-2007)

Related Topics

Popular Owner Manuals

Latest Owner Manuals