2013-2016 Mazda Cx-5 SUV Child Restraint User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Child Restraint for Your Mazda Cx-5 SUV First Generation (2013-2016)

Essential Safety Equipment  
Seat Belt Systems  
Seat Belt Precautions  
Seat belts help to decrease the possibility of severe injury during accidents and sudden  
stops. Mazda recommends that the driver and all passengers always wear seat belts.  
All of the seat belt retractors are designed to keep the lap/shoulder belts out of the way  
when not in use.  
The driver's seat belt has no provisions for child-restraint systems and has only an  
emergency locking mode. The driver may wear it comfortably, and it will lock during a  
collision.  
However, in some models (with automatic locking mode) the front passenger's seat and all  
rear lap/shoulder belt retractors operate in two modes: emergency locking mode, and for  
child-restraint systems, automatic locking mode. While we recommend you put all children  
in the rear seats, if you must use the front passenger seat for a child, slide the front  
passenger seat as far back as possible and make sure any child-restraint system is secured  
properly.  
WARNING  
Always wear your seat belt and make sure all occupants are properly restrained:  
Not wearing a seat belt is extremely dangerous. During a collision, occupants not  
wearing seat belts could hit someone or things inside the vehicle or even be thrown  
out of the vehicle. They could be seriously injured or even killed. In the same  
collision, occupants wearing seat belts would be much safer.  
Do not wear twisted seat belts:  
Twisted seat belts are dangerous. In a collision, the full width of the belt is not  
available to absorb the impact. This puts more force on the bones beneath the belt,  
which could cause serious injury or death. So, if your seat belt is twisted, you must  
straighten the seat belt to remove any twists and to allow the full width of the belt to  
be used.  
Never use one seat belt on more than one person at a time:  
Using one seat belt for more than one person at a time is dangerous. A seat belt  
used in this way cannot spread the impact forces properly and the two passengers  
could be crushed together and seriously injured or even killed. Never use one belt for  
more than one person at a time and always operate the vehicle with each occupant  
properly restrained.  
Do not operate a vehicle with a damaged seat belt:  
Using a damaged seat belt is dangerous. An accident could damage the belt  
webbing of the seat belt in use. A damaged seat belt cannot provide adequate  
protection in a collision. Have an Authorized Mazda Dealer inspect all seat belt  
systems in use during an accident before they are used again.  
2-17  
Essential Safety Equipment  
Seat Belt Systems  
Have your seat belts changed immediately if the pretensioner or load limiter has  
been expended:  
Always have an Authorized Mazda Dealer immediately inspect the front seat belt  
pretensioners and air bags after any collision. Like the air bags, the front seat belt  
pretensioners and load limiters will only function once and must be replaced after  
any collision that caused them to deploy. A seat belt with an expended pretensioner  
or load limiter is still better than wearing no seat belt at all; however, if the front  
seat belt pretensioners and load limiters are not replaced, the risk of injury in a  
collision will increase.  
Positioning the Shoulder Portion of the Seat Belt:  
Improper positioning of the shoulder portion of the seat belt is dangerous. Always  
make sure the shoulder portion of the seat belt is positioned across your shoulder  
and near your neck, but never under your arm, on your neck, or on your upper arm.  
Positioning the Lap Portion of the Seat Belt:  
The lap portion of the seat belt worn too high is dangerous. In a collision, this would  
concentrate the impact force directly on the abdominal area, causing serious injury.  
Wear the lap portion of the belt snugly and as low as possible.  
In a rollover crash, an unbelted person is significantly more likely to die than a  
person wearing a seat belt.  
CAUTION  
Belt retraction may become difficult if the belts and rings are soiled, so try to keep  
them clean. For more details about cleaning the seat belts, refer to Seat Belt  
Maintenance(page 6-70).  
Ring  
2-18  
Essential Safety Equipment  
Seat Belt Systems  
qPregnant Women and Persons with Serious Medical Conditions  
Pregnant women should always wear seat belts. Ask your doctor for specific  
recommendations.  
The lap belt should be worn SNUGLYAND AS LOWAS POSSIBLE OVER THE HIPS.  
The shoulder belt should be worn across your shoulder properly, but never across the  
stomach area.  
Persons with serious medical conditions also should wear seat belts. Check with your  
doctor for any special instructions regarding specific medical conditions.  
qEmergency Locking Mode  
When the seat belt is fastened, it will always be in the emergency locking mode.  
In the emergency locking mode, the belt remains comfortable on the occupant and the  
retractor will lock in position during a collision.  
If the belt is locked and cannot be pulled out, retract the belt once, and then try pulling it  
out slowly. If this fails, pull the belt strongly one time and loosen, then pull it out again  
slowly.  
(Seat Belt with Automatic Locking Mode)  
When the seat belt is fastened, it will always be in the emergency locking mode until it is  
switched to automatic locking mode by pulling it all the way out to its full length. If the  
belt feels tight and hinders comfortable movement while the vehicle is stopped or in  
motion, it may be in the automatic locking mode because the belt has been pulled too far  
out. To return the belt to the more comfortable emergency locking mode, wait until the  
vehicle has stopped in a safe, level area, retract the belt fully to convert it back to  
emergency locking mode and then extend it around you again.  
qAutomatic Locking Mode  
Always use the automatic locking mode to keep the child-restraint system from shifting to  
an unsafe position in the event of an accident. To enable seat belt automatic locking mode,  
pull it all the way out and connect it as instructed on the child-restraint system. It will  
retract down to the child-restraint system and stay locked on it. See the section on child  
restraint (page 2-26).  
2-19  
Essential Safety Equipment  
Seat Belt Systems  
qUnfastening the Seat Belt  
Seat Belt  
Depress the button on the seat belt buckle.  
If the belt does not fully retract, pull it out  
and check for kinks or twists. Then make  
sure it remains untwisted as it retracts.  
qFastening the Seat Belt  
Seat belt tongue  
Seat belt  
buckle  
Position the lap belt as low as possible,  
not on the abdominal area, then adjust the  
shoulder belt so that it fits snugly against  
your body.  
Button  
NOTE  
If a belt does not fully retract, inspect it for  
kinks and twists. If it is still not retracting  
properly, have it inspected at an Authorized  
Mazda Dealer.  
Take up slack  
qFront Shoulder Belt Adjuster  
Keep low on  
hip bone  
To raise  
To lower  
Too high  
Make sure the adjuster is locked.  
2-20  
Essential Safety Equipment  
Seat Belt Systems  
Seat Belt Warning Systems  
Front Seat Belt Pretensioner  
and Load Limiting Systems  
If it detects that the driver's seat belt is  
unfastened, the warning light or beep  
alerts the driver.  
Refer to Warning/Indicator Lights on page  
4-20.  
For optimum protection, the driver and  
front passenger seat belts are equipped  
with pretensioner and load limiting  
systems. For both these systems to work  
properly you must wear the seat belt  
properly.  
Pretensioners:  
In moderate or severe frontal or near-  
frontal accidents, the front air bag and  
pretensioner systems deploy  
simultaneously.  
For deployment details, refer to the SRS  
Air Bag Deployment Criteria (page 2-57).  
The front seat belt retractors remove slack  
quickly as the air bags are expanding.  
Any time the air bags and seat belt  
pretensioners have fired they must be  
replaced.  
A system malfunction or operation  
conditions are indicated by a warning.  
Refer to Warning/Indicator Lights on page  
4-20.  
Refer to Air Bag/Front Seat Belt  
Pretensioner System Warning Beep on  
page 7-35.  
(With Front Passenger Occupant  
Classification System)  
In addition, the pretensioner system for  
the front passenger, like the front and side  
passenger air bag, is designed to only  
deploy when the front passenger occupant  
classification sensor detects a passenger  
sitting on the front passenger's seat.  
For details, refer to the front passenger  
occupant classification sensor (page  
2-60).  
2-21  
Essential Safety Equipment  
Seat Belt Systems  
Load limiter:  
Have your seat belts changed  
immediately if the pretensioner or load  
limiter has been expended:  
The load limiting system releases belt  
webbing in a controlled manner to reduce  
belt force on the occupant's chest. While  
the most severe load on a seat belt occurs  
in frontal collisions, the load limiter has  
an automatic mechanical function and can  
activate in any accident mode with  
sufficient occupant movement.  
Always have an Authorized Mazda  
Dealer immediately inspect the front  
seat belt pretensioners and air bags  
after any collision. Like the air bags,  
the front seat belt pretensioners and  
load limiters will only function once  
and must be replaced after any  
collision that caused them to deploy.  
A seat belt with an expended  
Even if the pretensioners have not fired,  
the load limiting function must be  
checked by an Authorized Mazda Dealer.  
pretensioner or load limiter is still  
better than wearing no seat belt at  
all; however, if the front seat belt  
pretensioners and load limiters are  
not replaced, the risk of injury in a  
collision will increase.  
WARNING  
Wear seat belts only as recommended  
in this owner's manual:  
Incorrect positioning of the driver and  
front passenger seat belts is  
dangerous. Without proper  
positioning, the pretensioner and  
load limiting systems cannot provide  
adequate protection in an accident  
and this could result in serious injury.  
For more details about wearing seat  
belts, refer to Fastening the seat  
belts(page 2-20).  
Do not modify the components or  
wiring, or use electronic testing devices  
on the pretensioner system:  
Modifying the components or wiring  
of the pretensioner system, including  
the use of electronic testing devices is  
dangerous. You could accidentally  
activate it or make it inoperable  
which would prevent it from  
activating in an accident. The  
occupants or repairers could be  
seriously injured.  
Properly dispose of the pretensioner  
system:  
Improper disposal of the pretensioner  
system or a vehicle with non-  
deactivated pretensioners is  
dangerous. Unless all safety  
procedures are followed, injury could  
result. Have an Authorized Mazda  
Dealer safely dispose of the  
pretensioner system or scrap a  
pretensioner system equipped vehicle.  
2-22  
Essential Safety Equipment  
Seat Belt Systems  
NOTE  
Center-Rear Position Seat  
Belt  
l
The pretensioner system will activate in a  
moderate or greater frontal or near-frontal,  
or a severe side collision. It will not  
activate in most rollovers, rear impacts.  
(With Front Passenger Occupant  
Classification System)  
Before using the center-rear lap/shoulder  
belt make sure tongue (A) and anchor  
buckle (B) are fastened.  
The pretensioner system will activate in a  
severe roll-over accident.  
(A)  
(B)  
In addition, the pretensioner system for the  
front passenger is designed to only deploy  
when the front passenger occupant  
classification sensor detects a passenger  
sitting on the front passenger's seat.  
Some smoke (non-toxic gas) will be  
released when the air bags and  
l
pretensioners deploy. This does not indicate  
a fire. This gas normally has no effect on  
occupants, however, those with sensitive  
skin may experience light skin irritation. If  
residue from the deployment of the air bags  
or the front pretensioner system gets on the  
skin or in the eyes, wash it off as soon as  
possible.  
qFastening the Seat Belt  
1. Grasp the seat belt tongue (C).  
2. Slowly pull out the lap/shoulder belt.  
3. Insert the seat belt tongue (C) into the  
seat belt buckle (D) until you hear a  
click sound.  
(C)  
(D)  
(A)  
(B)  
2-23  
Essential Safety Equipment  
Seat Belt Systems  
Seat Belt Extender  
WARNING  
Fastening the Center-Rear Seat Belt  
with Only One Buckle:  
If your seat belt is not long enough, even  
when fully extended, a seat belt extender  
may be available to you at no charge from  
your Authorized Mazda Dealer.  
This extender will be only for you and for  
the particular vehicle and seat. Even if it  
plugs into other seat belts, it may not hold  
in the critical moment of a crash.  
When ordering an extender, only order  
one that provides the necessary additional  
length to fasten the seat belt properly.  
Please contact your Authorized Mazda  
Dealer for more information.  
Fastening the center-rear seat belt  
with only one buckle is dangerous. If  
only one pair of seat belt tongues  
and buckles is fastened (either seat  
belt tongue (C) and seat belt anchor  
buckle (D) or seat belt tongue (A) and  
seat belt buckle (B)), then the seat  
belt cannot provide full protection. In  
a sudden stop or collision, the user  
could slide under the belt and suffer  
serious injuries. Always make sure  
that both pairs of seat belt tongues  
and buckles are fastened properly.  
WARNING  
Do not use a seat belt extender unless  
it is necessary:  
Using a seat belt extender when not  
necessary is dangerous. The seat belt  
will be too long and not fit properly.  
In an accident, the seat belt will not  
provide adequate protection and you  
could be seriously injured. Only use  
the extender when it is required to  
fasten the seat belt properly.  
2-24  
Essential Safety Equipment  
Seat Belt Systems  
Do not use an improper extender:  
Using a seat belt extender that is for  
another person or a different vehicle  
or seat is dangerous. The seat belt  
will not provide adequate protection  
and the user could be seriously  
Do not leave a seat belt extender  
connected to the buckle:  
Leaving a seat belt extender  
connected to the buckle without  
using the seat belt is dangerous.  
When the seat belt extender is  
connected to the driver's seat belt  
buckle (or front passenger) seat, the  
SRS driver's (or front passenger's) air  
bag system will determine that the  
driver (or front passenger) is wearing  
the seat belt even if the driver (or  
front passenger) is not wearing it.  
This condition could cause the  
driver's (or front passenger's) air bag  
to not activate correctly and result in  
death or serious injury in the event of  
collision. Always wear the seat belt  
with the seat belt extender.  
injured in an accident. Only use the  
extender provided for you and for the  
particular vehicle and seat. NEVER  
use the extender in a different vehicle  
or seat. If you sell your Mazda, do  
not leave your seat belt extender in  
the vehicle. It could be used  
accidentally by the new owner of the  
vehicle. After removing the seat belt  
extender, discard it. Never use the  
seat belt extender in any other  
vehicle you may own in the future.  
Do not use an extender that is too  
long:  
Do not use the seat belt extender when  
installing a child-restraint system on  
the front or rear passenger seat:  
Using a seat belt extender to fasten a  
child-restraint system on any seat is  
dangerous. Always follow the child-  
restraint system manufacturer's  
installation instructions and never  
use a seat belt extender.  
Using an extender that is too long is  
dangerous. The seat belt will not fit  
properly. In an accident, the seat belt  
will not provide adequate protection  
and you could be seriously injured.  
Do not use the extender or choose  
one shorter in length if the distance  
between the extender's buckle and  
the center of the user's body is less  
than 15 cm (6 in).  
NOTE  
When not in use, remove the seat belt extender  
and store it in the vehicle. If the seat belt  
extender is left connected, the seat belt  
extender might get damaged as it will not  
retract with the rest of the seat belt and can  
easily fall out of the door when not in use and  
be damaged. In addition, the seat belt warning  
light will not illuminate and function properly.  
2-25  

Related Topics

Popular Owner Manuals