Get Seats -> Front Seat Guide for Mazda Cx-5 SUV First Generation (2013-2016)

Essential Safety Equipment

Seats

Front Seat

qSeat Operation

Power operation

Seat Slide

(Manual Seat)

To move a seat forward or backward, raise the lever and slide the seat to the desired

position and release the lever.

Make sure the lever returns to its original position and the seat is locked in place by

attempting to push it forward and backward.

(Power Seat)

To slide the seat, move the slide lifter switch on the outside of the seat to the front or back

and hold it. Release the switch at the desired position.

Height Adjustment

(Manual Seat)

To adjust the seat height, move the lever up or down.

(Power Seat)

To adjust the seat height, move the switch up or down.

Front Height Adjustment of Seat Bottom (Driver's Power Seat)^í

To adjust the front height of the seat bottom, raise or lower the front of the slide lifter

switch.

^íSome models.

2-5

Essential Safety Equipment

Seats

Seat Recline

(Manual Seat)

To change the seatback angle, lean forward slightly while raising the lever. Then lean back

to the desired position and release the lever.

Make sure the lever returns to its original position and the seatback is locked in place by

attempting to push it forward and backward.

(Power Seat)

To change the seatback angle, press the front or rear side of the reclining switch. Release

the switch at the desired position.

Lumbar Support Adjustment (Driver's Seat)^í

(Manual Operation)

To increase the seat firmness, push the lever forward. Pull the lever backward to decrease

firmness.

(Power Operation)

To increase the seat firmness, press and hold the front part of the switch to the desired

position, then release it.

Press the rear part of the switch to decrease firmness.

2-6

^íSome models.

Essential Safety Equipment

Seats

qSeat Warmer^í

WARNING

The front seats are electrically heated. The

ignition must be switched ON.

Be careful when using the seat warmer:

The heat from the seat warmer may

be too hot for some people, as

indicated below, and could cause a

low-temperature burn.

Press the seat warmer switch to illuminate

the indicator light while the ignition is

switched ON. The mode changes as

follow each time the seat warmer switch is

pressed.

Ø Infants, small babies, elderly

people, and physically challenged

people

Ø People with delicate skin

Ø People who are excessively

fatigued

Fully Automatic Type Climate Control

OFF

Ø People who are intoxicated

Ø People who have taken sleep-

inducing medicine such as

sleeping pills or cold medicine

High

Mid

Low

Do not use the seat warmer with

anything having high moisture-

retention ability such as a blanket or

cushion on the seat:

The seat may be heated excessively

and cause a low-temperature burn.

Manual Type Climate Control

Do not use the seat warmer even when

taking a short nap in the vehicle:

The seat may be heated excessively

and cause a low-temperature burn.

OFF

High

Mid

Low

Do not place heavy objects with sharp

projections on the seat, or insert

needles or pins into it:

This could cause the seat to become

excessively heated and result in injury

from a minor burn.

CAUTION

Do not use organic solvents to clean

the seat. It may damage the seat

surface and the heater.

^íSome models.

2-7

Essential Safety Equipment

Seats

NOTE

l

If the ignition is switched off while the seat

SET button

warmer is operating (High, Mid or Low)

and then switched ON again, the seat

warmer will automatically operate at the

temperature set before switching off the

ignition.

l

Use the seat warmer when the engine is

running. Leaving the seat warmer on for

long periods with the engine not running

could cause the battery power to be

depleted.

l

The temperature of the seat warmer cannot

The seat position can be programmed or

operated using the following operations.

be adjusted beyond High, Mid and Low

because the seat warmer is controlled by a

thermostat.

l

Operation of the buttons on the side of

the seat.

Operation using the key.

l

qSeat Position Memory (Driver's

seat)^í

NOTE

l

Individual seat positions can be

The seat position memory function allows

you to program the driver's seat to a

desired seat position and to call up a

programmed position with the simple

touch of a button.

programmed to the two available

programming buttons on the side of the

driver's seat, plus one seat position for each

registered key.

l

If the vehicle has been serviced and the

battery cables disconnected, the

programmed seat positions will have been

erased. Re-program the seat positions.

CAUTION

Do not place fingers or hands around

the bottom of the seat while the seat

memory function is operating. The

seat moves automatically while the

seat memory function is operating

and fingers or hands could get

pinched and injured.

Programming

1. Switch the ignition OFF.

2. Adjust the seat to the desired position

using the slide lifter and reclining

switches.

Refer to Seat Operation on page 2-5.

3. Press the SET button on the seat until a

beep sound is heard one time.

2-8

^íSome models.

Essential Safety Equipment

Seats

4. Perform one of the following settings

within 5 seconds of completing step 3

above:

NOTE

l

If seat movement is not required, only the

beep sounds.

l

When the ignition is switched ON, the seat

position memory function does not operate

unless the selector lever is in the P position

(Automatic transaxle) or the parking brake

is applied (Manual transaxle).

l

Programming to a button on the seat

side

Press the button you want to

program, either button 1 or 2, until a

beep sound is heard one time.

l

When the ignition is switched OFF, the seat

position memory function is operable while

the selector lever is in a position other than

P position (Automatic transaxle) or the

parking brake is not applied (Manual

transaxle), however, if the ignition is

switched ON while the seat position

memory function is operating, the operation

is stopped.

l

Programming to the key

Press the key switch until a beep

sound is heard one time.

NOTE

If a beep sound is heard three times, the

operation is canceled.

Adjusting a programmed position

l

The seat position adjustment is canceled in

the following cases:

(Programming to a button on the seat

side)

l

Any of the seat adjustment switches is

1. While the vehicle is stopped, press the

programming button for the seat

position you want to call up (button 1

or 2).

operated.

The SET button is pressed.

Programming button 1 or 2 is pressed.

The key lock switch or unlock switch is

l

operated.

The vehicle starts moving.

2. A beep sound is heard when the seat

position adjustment is completed.

l

(When programming to the key)

1. Unlock the doors by pressing a request

switch or the key switch.

2. After unlocking the doors, the seat

position adjustment begins within 40

seconds of opening the driver's door,

and a beep sounds when the operation

is finished.

2-9

Seats -> Front Seat for Your Mazda Cx-5 SUV First Generation (2013-2016)

Related Topics

Popular Owner Manuals

Latest Owner Manuals