2007-2013 Mercedes C Class 4 Door On-board computer and displays -> Menus and submenus User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

On-board computer and displays -> Menus and submenus for Your Mercedes C Class 4 Door Second Generation (2007-2013)

A
Permanentdisplay: outside temperature
or speed (Y page 209)
B
Transmission position
X
To show menu bar ;: press the =
or ; button on the steering wheel.
Menu bar ; disappears after a few seconds.
Text field : shows the selected menu or
submenu as well as display messages.
i
You can set the time using the audio
system or COMAND, see the separate
operating instructions.
The following messages may appear in the
multifunction display:
XjY Parking Guidance (Y page 182)
CRUISE
Cruise control (Y page 165)
_
Adaptive Highbeam Assist
(Y page 114)
À
ATTENTION ASSIST(Ypage 185)
¤
ECO start/stop function
(Y page 145)
Ã
Lane Keeping Assist (Y page 188)or
Active Lane Keeping Assist
(Y page 193)
ë
HOLD function (Y page 176)
Ä
PRE-SAFE
®
Brake (Y page 69)
Menus and submenus
Menu overview
Operating the on-board computer
(Y page 199).
Depending on the equipment installed in the
vehicle, you can call up the following menus:
R
Trip menu (Y page 201)
R
Navi
menu (navigation instructions)
(Y page 203)
R
Audio menu (Y page 204)
R
Tel menu (telephone) (Y page 205)
R
DriveAssist
menu (assistance)
(Y page 206)
R
Serv menu (Y page 208)
R
Sett. menu (settings) (Y page 208)
R
AMG
menu in AMG vehicles (Y page 212)
The
Audio, Navi and Tel menus differslightly
in vehicles with an audio system and in
vehicles with COMAND.The examples given
in this Operator's Manual apply to vehicles
equipped with COMAND.
Trip menu
Standard display
X
Press and hold the % button on the
steering wheel until the
Trip menu with
trip odometer : and odometer ; is
shown.
Trip computer "From Start" or "From
Reset"
Example: trip computer "From Start"
:
Distance
;
Time
=
Average speed
?
Average fuel consumption
X
Press the = or ; button on the
steering wheel to select the
Trip
menu.
X
Press the 9 or : button to select
From Start or From Reset.
The values in the
From Start submenu are
calculated from the start of a journey,
Menus and submenus
201
On-board computer and displays
Z
whereas the values in the From Reset
submenu are calculated fromthe last time the
submenu was reset (Y page 202).
The
From Start
trip computer is
automatically reset if:
R
the ignition has been switched off for more
than four hours.
R
999 hours have been exceeded.
R
9999 miles have been exceeded.
The
From Reset trip computer is
automatically reset if the value exceeds
9,999 hours or 99,999 miles.
Displaying the range and current fuel
consumption
X
Press the = or ; button on the
steering wheel to select the
Trip menu.
X
Press the 9 or : button to select the
current fuel consumption and the
approximate range (except for AMG
vehicles).
The approximate range that can be covered
depends on the fuel level and your current
driving style. If there is only a small amount
of fuel left in the fuel tank, the display shows
a vehicle being refueled C instead of the
range.
ECO display
Example: ECO display
X
Press the = or ; button on the
steering wheel to select the
Trip
menu.
X
Press 9 or : to select
ECO
DISPLAY.
If the ignition remains switched off for longer
than four hours, the ECO display will be
automatically reset.
Further information on the ECO display
(Y page 161).
Digital speedometer
:
Digital speedometer
X
Press the = or ; button on the
steering wheel to select the
Trip menu.
X
Press the 9 or : button to select the
digital speedometer.
Resetting values
Example: resetting the trip computer "From Start"
X
Press the = or ; button on the
steering wheel to select the
Trip menu.
X
Press the 9 or : button to select the
function that you wish to reset.
X
Press the a button.
X
Press the : button to select
Yes and
press the a button to confirm.
202
Menus and submenus
On-board computer and displays
You can reset the values of the following
functions:
R
Trip odometer
R
"From Start" trip computer
R
"From Reset" trip computer
R
ECO display
Navigation system menu
Displaying navigation instructions
In the Navi menu, the multifunction display
shows navigation instructions.For more
information, see the separate operating
instructions.
X
Switch on the audio system with Becker
®
MAP PILOT or COMAND; see the separate
operating instructions.
X
Press the = or ; button on the
steering wheel to select the
Navi menu.
Route guidance not active
:
Direction of travel
;
Current road
Route guidance active
No change of direction announced
:
Distance to the destination
;
Distance to the next change of direction
=
Current road
?
"Follow the road's course" symbol
Change of direction announced without a
lane recommendation
:
Road into which the change of direction
leads
;
Distance to change of direction and visual
distance display
=
Change-of-direction symbol
When a change of direction is announced, you
will see symbol = for the change of direction
and distance graphic ;.The distance
indicator shortens towards the top of the
display as you approach the point of the
announced change of direction.
Change of direction announced with a
lane recommendation
:
Road into which the change of direction
leads
;
Distance to change of direction and visual
distance display
=
New lane during a change of direction
?
Uninterrupted lane
A
Lane recommendation
B
Change-of-direction symbol
On multilane roads, the system can display
lane recommendation A for the next change
of direction. During the change of direction,
additional lanes may be displayed.
Menus and submenus
203
On-board computer and displays
Z
Lane recommendations are only displayed if
the relevant data is available on the digital
map.
Other status indicators of the
navigation system
R
O:you have reached the destination or an
intermediate destination.
R
New Route... or Calculating Route:
calculating a new route
R
Off Map or Off Mapped Road:the vehicle
position is outside the area of the digital
map (off-map position).
R
No Route
:no route could be calculated to
the selected destination.
Audio menu
Selecting aradio station
i
SIRIUS XM satellite radio functions like a
normal radio.
For more information on satellite radio
operation, see the separate operating
instructions.
i
For information on switching waveband
and storing stations; see the separate
operating instructions.
X
Switch on the audio system or COMAND
and select Radio (see the separate
operating instructions).
X
Press the = or ; button on the
steering wheel to select the
Audio menu.
:
Waveband
;
Station frequency with memory position
X
To selectastoredstation: briefly press
the 9 or : button.
X
To select a station from the station
list: press and briefly hold the 9
or : button.
If no stationlist is received:
X
To select astation using the station
search: press and briefly hold the 9
or : button.
Operating an audio player or audio
media
Audio data from various audiodevices or
media can be played, depending on the
equipment installed in the vehicle.
X
Switch on the audio system or COMAND
and select the audio player or medium, see
the separate operating instructions.
X
Press the = or ; button on the
steering wheel to select the
Audio menu.
Example: CD/DVD changer display
:
Current title
X
To select the next/previous track:
briefly press the 9 or : button.
X
To select a track from the track list
(rapid scrolling): press and hold the
9 or : button until desired trackhas
been reached.
If you press and hold 9 or :, the rapid
scrolling speed is increased. Not all audio
drives or data carriers support this function.
If track information is stored on the audio
device or medium, the multifunction display
will show the number and name of the track.
The currenttrack does not appear in audio
AUX mode (Auxiliary audio mode: external
audio source connected).
204
Menus and submenus
On-board computer and displays
Video DVD operation
X
Switch on COMAND and select video DVD;
see the separate operating instructions.
X
Press the = or ; button on the
steering wheel to select the
Audio
menu.
Example:CD/DVD changerdisplay
:
Current scene
X
To select the next/previousscene:
briefly press the 9 or : button.
X
To select ascene from the scene list
(rapid scrolling): press and hold the
9 or : buttonuntil desired scene
has been reached.
Telephone menu
Introduction
G
WARNING
If you operate informationsystems and
communication equipment integrated in the
vehicle while driving, you will be distracted
from traffic conditions. You could also lose
control of the vehicle. There is a risk of an
accident.
Only operate the equipmentwhen the traffic
situation permits. If you are not sure that this
is possible, park the vehicle paying attention
to traffic conditions and operate the
equipment when the vehicle is stationary.
When telephoning, you must observe the
legal requirements for the country in which
you are currently driving.
X
Switch on your mobile phone and audio
system or COMAND, see the separate
operating instructions.
X
Establish a Bluetooth
®
connection to the
audio system or COMAND; see the
separate operating instructions.
X
Press the = or ; button on the
steering wheel to select the
Tel menu.
You will see one of the following display
messages in the multifunction display:
R
Phone READY or the name of the network
provider: the mobile phone has found a
network and is ready to receive.
R
Phone No Service: there is no network
available or the mobile phone is searching
for a network.
Accepting acall
If someone calls you whenyou are in the
Tel menu, a display message appears in the
multifunction display, for example:
X
Press the 6 button on the steering
wheel to accept an incoming call.
You can accept a call even if you are not in
the
Tel
menu.
Rejecting or ending acall
X
Press the ~ button on the steering
wheel.
You can end or reject a call even if you are not
in the
Tel menu.
Menus and submenus
205
On-board computer and displays
Z
Dialing a number from the phone book
X
Press the = or ; button on the
steering wheel to selectthe
Tel
menu.
X
Press the 9, : or a button to
switch to the phone book.
X
Press the 9 or : button to select the
desired name.
or
X
To begin rapid scrolling: press and hold
the 9 or : button for longer than
one second.
Rapid scrolling stops when you release the
button or reach the end of the list.
X
If only one telephone number is stored
for a name: press the 6 or a button
to start dialing.
or
X
If there is more than one number for a
particular name: press the 6 or a
button to display the numbers.
X
Press the 9 or : button to select the
number you want to dial.
X
Press the 6 or a button to start
dialing.
or
X
To exit the telephone book: press the
~ or % button.
Redialing
The on-board computer saves the last names
or numbers dialed in the redial memory.
X
Press the = or ; button on the
steering wheel to select the
Tel menu.
X
Press the 6 button to switch to the
redial memory.
X
Press the 9 or : button to select the
desired name or number.
X
Press the 6 or a button to start
dialing.
or
X
If you do not want to make a call: press
the ~ or % button.
Assistance menu
Introduction
In the DriveAssist menu, you have the
following options:
R
Showing the distance display
(Y page 206)
R
Activating/deactivating
ESP
®
(Y page 207)
R
Activating/deactivating PRE-SAFE
®
Brake
(Y page 207)
R
Activating/deactivating ATTENTION
ASSIST (Y page 207)
R
Activating/deactivating Blind Spot Assist
or Active Blind Spot Assist (Y page 208)
R
Activating/deactivating Lane Keeping
Assist or Active Lane Keeping Assist
(Y page 208)
Showing the distance display
This function is only available with
DISTRONIC PLUS.
X
Press the = or ; button on the
steering wheel to select the
DriveAssist
menu.
X
Press the 9 or : button to select
Distance Display.
X
Press the a button.
The DISTRONIC PLUS distance display
(Y page 173) appears in the multifunction
display.
If the
Sensors Deactivated message
appears, the radar sensor system is
deactivated.
X
Switch on the radar sensor system
(Y page 211).
206
Menus and submenus
On-board computer and displays
Deactivating/activating ESP
®
G
WARNING
If you deactivate ESP
®
, ESP
®
no longer
stabilizes the vehicle. There is an increased
risk of skidding and an accident.
Only deactivate ESP
®
in the situations
described in the following.
Activating/deactivatingESP
®
on AMG
vehicles (Y page 68).
For further information about ESP
®
, see
(Y page 66).
X
Start the engine.
X
Press the = or ; button on the
steering wheel to select the
DriveAssist
menu.
X
Press the 9 or : button to select
ESP.
X
Press the a button.
X
To deactivate: press a again.
The å warning lamp in the instrument
cluster lights up.
X
To activate: press a again.
The å warning lamp in the instrument
cluster goes out.
ESP
®
is deactivated if the å warning lamp
in the instrument cluster lights up
continuously when the engine is running.
If the ÷ warning lamp and the å
warning lamp are litcontinuously, ESP
®
is not
available due to a malfunction.
It may be best to deactivate ESP
®
in the
following situations:
R
when using snow chains
R
in deep snow
R
on sand or gravel
Observe the information on warning lamps
(Y page 246).
Observe the information on display messages
(Y page 217).
Activating/deactivating PRE-SAFE
®
Brake
PRE-SAFE
®
Brake is only available in vehicles
with DISTRONIC PLUS.
X
Press the = or ; button on the
steering wheel to select the
DriveAssist
menu.
X
Press the 9 or : button to select
PRE-SAFE Brake.
X
Press the a button.
The current selection is displayed.
X
To activate/deactivate: press the a
button again.
When PRE-SAFE
®
Brake (Y page 69) is
activated, the multifunction display shows
the Ä symbol as long as the HOLD
function is not activated (Y page 176).
Vehicles with Parking Guidance: if
PARKTRONIC is activated and you are driving
at a speed below 22 mph (35 km/h), the j
Parking Guidance symbol is shown instead of
the Ä symbol.
If the
PRE-SAFE Brake: Sensors
Deactivated message appears, the radar
sensor system is deactivated.
X
Switch on the radar sensor system
(Y page 211).
For more information on PRE-SAFE
®
Brake,
see (Y page 69).
Activating/deactivating ATTENTION
ASSIST
X
Press the = or ; button on the
steering wheel to select the
DriveAssist
menu.
X
Press the 9 or : button to select
Attention Assist.
X
Press the a button.
The current selection is displayed.
X
To activate/deactivate: press the a
button again.
Menus and submenus
207
On-board computer and displays
Z
When ATTENTION ASSIST(Ypage 185) is
activated, the À symbol appears in the
multifunction display when the ignition is on.
For further information about ATTENTION
ASSIST, see (Y page 185).
Activating/deactivating Blind Spot
Assist
X
Press the = or ; button on the
steering wheel to select the
DriveAssist
menu.
X
Press the 9 or : button to select
Blind Spot Assist.
X
Press the a button.
The currentselection is displayed.
X
To activate/deactivate: press the a
button again.
If the
Blind Spot Assist Sensors
Deactivated or Act. Blind Spot Asst.
Sensors Deactivated message appears,
the radar sensor system is deactivated.
X
Switch on the radar sensor system
(Y page 211).
For further information about Blind Spot
Assist, see (Y page 186).
For further information about Active Blind
Spot Assist, see (Y page 190).
Activating/deactivating Lane Keeping
Assist
X
Press the = or ; button on the
steering wheel to select the
DriveAssist
menu.
X
Press the 9 or : button to select
Lane Keep. Asst.
X
Press the a button.
The currentselection is displayed.
X
Press a to confirm.
X
Press the : or 9 button to set
Off,
Standard
or Adaptive.
X
Press the a button to save the setting.
When Lane Keeping Assist or Active Lane
Keeping Assist is activated, the à symbol
appears in the multifunction display when the
ignition is on.
For further information about Lane Keeping
Assist, see (Y page 188).
For further information about Active Lane
Keeping Assist, see (Y page 193).
Maintenance menu
In the Serv. menu, you have the following
options:
R
Calling up display messages
(Y page 216)
R
Restarting the tire pressure loss warning
system (Canada only) (Y page 317)
R
Checking the tire pressure electronically
(Y page 318)
R
Calling up the service due date
(Y page 282)
Settings menu
Introduction
In the Sett. menu, you have the following
options:
R
Changing the instrument cluster settings
(Y page 209)
R
Changing the light settings (Y page 209)
208
Menus and submenus
On-board computer and displays
R
Changing the vehicle settings
(Y page 211)
R
Changing the convenience settings
(Y page 211)
R
Restoring the factory settings
(Y page 212)
Instrumentcluster
Selecting the unit of measurement for
distance
The
Display Unit Speed-/Odometer:
function allows you to choose whether
certain displays appear in kilometers or miles
in the multifunction display.
You can determine whether the multifunction
display shows some messages in miles or
kilometers.
X
Press the = or ; button on the
steering wheel to selectthe
Sett. menu.
X
Press the : or 9 button to select the
Instr. Cluster submenu.
X
Press a to confirm.
X
Press the : or 9 button to select the
Display Unit Speed-/Odometer:
function.
You will see the selected setting:
km or
miles
.
X
Press the a button to save the setting.
The selected unit of measurement for
distance applies to:
R
the digital speedometer in the
Trip
menu
R
the odometer and the trip odometer
R
the trip computer
R
current consumption and the range
R
the navigation instructions in the
Navi
menu
R
cruise control
R
DISTRONIC PLUS
R
ASSYST PLUS service interval display
Selecting the permanent display function
You can determine whether the multifunction
display permanently shows your speed or the
outside temperature.
X
Press the = or ; button on the
steering wheel to select the
Sett. menu.
X
Press the : or 9 button to select the
Instr. Cluster submenu.
X
Press a to confirm.
X
Press the : or 9 button to select the
Permanent Display: function.
You will see the selected setting
Outside
Temperature or Speedometer [km/h]
(USA)/Speedometer [mph] (Canada).
X
Press the a button to save the setting.
i
The speed is shown in km/h (USA)/mph
(Canada).
Lights
Switching the daytime running lamps on/
off
Daytime running lamps are required by law
(Canada only). You cannot set the "daytime
running lamps" function via the on-board
computer.
X
Press the = or ; button on the
steering wheel to select the
Sett.
menu.
X
Press the : or 9 button to select the
Lights submenu.
X
Press a to confirm.
X
Press the : or 9 button to select the
Day Lights function.
If the
Day Lights function has been
switched on, the cone of light and the
W symbol in the multifunction display
are shown in red.
X
Press the a button to save the setting.
Further information on daytime running
lamps (Y page 111).
Menus and submenus
209
On-board computer and displays
Z
Switching Adaptive Highbeam Assist on/
off
X
Press the = or ; button on the
steering wheel to select the
Sett. menu.
X
Press the : or 9 button to select the
Lights submenu.
X
Press a to confirm.
X
Press the : or 9 button to select the
Adapt. Highbeam function.
If the
Adapt. Highbeam function has been
switched on, the cone of light and the
_ symbol in the upper multifunction
display are shown in red.
X
Press the a button to save the setting.
For further information about Adaptive
Highbeam Assist, see (Y page 114).
Activating/deactivating surround
lighting and exterior lighting delayed
switch-off
X
Press the = or ; button on the
steering wheel to select the
Sett.
menu.
X
Press the : or 9 button to select the
Lights submenu.
X
Press a to confirm.
X
Press the : or 9 button to select the
Surround Lighting
function.
When the
Surround Lighting
function is
activated, the light cone and the area
around the vehicle are displayed in red in
the multifunction display.
X
Press the a button to save the setting.
Deactivating delayed switch-offofthe
exterior lighting temporarily:
X
Before leaving the vehicle, turn the
SmartKey to position 0 in the ignition lock.
X
Turn the SmartKey to position 2 in the
ignition lock.
The exterior lighting delayed switch-off is
deactivated.
Delayed switch-off of the exterior lighting is
reactivated the next time you start the
engine.
If you have activated the
Surround
Lighting function and the light switch is set
to Ã, the following functions are activated
when it is dark:
R
surround lighting: the exterior lighting
remains lit for 40 seconds after unlocking
with the key. If you start the engine, the
surround lighting is switched off and
automatic headlamp mode is activated
(Y page 111).
R
exterior lighting delayed switch-off: the
exterior lighting remains lit for
60 seconds after the engine is switched off.
If you close all the doors and the trunk lid,
the exterior lighting goes off after
5seconds.
i Depending on your vehicle's equipment,
when the surround lighting and delayed
switch-off exterior lighting are on, the
following light up:
R
Parking lamps
R
Front fog lamps
R
Low-beam headlamps
R
Daytime running lamps
R
Side marker lamps
R
Surround lighting in the exterior mirrors
Activating/deactivating the interior
lighting delayed switch-off
If you activate the
Light. Delay function,
the interior lighting remains on for
20 seconds after you remove the key from the
ignition lock.
X
Press the = or ; button on the
steering wheel to select the
Sett. menu.
X
Press the : or 9 button to select the
Lights submenu.
X
Press a to confirm.
X
Press the : or 9 button to select the
Light. Delay
function.
When the
Light. Delay
function is
activated, the vehicle interior is displayed
in red in the multifunction display.
X
Press the a button to save the setting.
210
Menus and submenus
On-board computer and displays
Vehicle
Activating/deactivating the automatic
doorlocking mechanism
X
Press the = or ; button on the
steering wheel to selectthe
Sett.
menu.
X
Press the : or 9 button to select the
Vehicle submenu.
X
Press a to confirm.
X
Press the : or 9 button to select the
Auto. Door Locks function.
When the
Auto. Door Locks function is
activated, the vehicle doors are displayed
in red in the multifunction display.
X
Press the a button to save the setting.
If you activate the
Auto. Door Locks
function, the vehicle is centrally locked above
a speed of around 9 mph (15 km/h).
For further information on the automatic
locking feature, see (Y page 81).
Activating/deactivating the acoustic
locking verification signal
If you switch on the
Acoustic Lock function,
an acoustic signal sounds when you lock the
vehicle.
X
Press the = or ; button on the
steering wheel to select the
Sett. menu.
X
Press the : or 9 button to select the
Vehicle submenu.
X
Press a to confirm.
X
Press the : or 9 button to select the
Acoustic Lock function.
If the
Acoustic Lock function is activated,
the & symbol in the multifunction
display lights up red.
X
Press the a button to save the setting.
Activating/deactivating the radar sensor
system
X
Press the = or ; button on the
steering wheel to select the
Sett. menu.
X
Press the : or 9 button to select the
Vehicle submenu.
X
Press a to confirm.
X
Press the 9 or : button to select
Radar Sensor (See Oper. Manual):
.
You will see the selected setting:
Enabled
or Disabled.
X
Press the a button to save the setting.
The following systems are switched off when
the radar sensor system is deactivated:
R
DISTRONIC PLUS (Y page 167)
R
BAS PLUS (Y page 65)
R
PRE-SAFE
®
Brake (Y page 69)
R
Blind Spot Assist (Y page 186) or Active
Blind Spot Assist (Y page 190)
Convenience
Activating/deactivating the EASY-
ENTRY/EXIT feature
G
WARNING
When the EASY-ENTRY/EXIT feature adjusts
the steering wheel and the driver's seat, you
and other vehicle occupants –particularly
children–could become trapped. There is a
risk of injury.
While the EASY-ENTRY/EXIT feature is
making adjustments, make sure that no one
has any body parts in the sweep of the seat
and the steering wheel.
If somebody becomes trapped:
R
press one of the memory function position
buttons, or
R
move the switch for steering wheel
adjustmentinthe opposite direction to that
in which the steering wheel is moving.
The adjustment process is stopped.
X
Press the = or ; button on the
steering wheel to select the
Sett.
menu.
X
Press the : or 9 button to select the
Convenience submenu.
X
Press a to confirm.
Menus and submenus
211
On-board computer and displays
Z
X
Press the : or 9 button to select the
Easy Entry/Exit function.
If the
Easy Entry/Exit function is
activated, the vehicle steering wheel is
displayed in red in the multifunction
display.
X
Press the a button to save the setting.
Further information on the EASY-ENTRY/EXIT
feature (Y page 102).
Switching the belt adjustment on/off
X
Press the = or ; button on the
steering wheel to select the
Sett. menu.
X
Press the : or 9 button to select the
Convenience submenu.
X
Press a to confirm.
X
Press the : or 9 button to select the
Belt Adjustment
function.
When the
Belt Adjustment
function is
activated, the vehicle seat belt is displayed
in red in the multifunction display.
X
Press the a button to save the setting.
For further information on belt adjustment,
see (Y page 56).
Switching the fold-in mirrors when
locking feature on/off
This function is only available on vehicles with
the memory function (Y page 106).
This function is only available in Canada.
When you activate the
Auto. Mirror
Folding function, the exterior mirrors are
folded in when the vehicle is locked. If you
unlock the vehicle and then open a door, the
exterior mirrors fold out again.
X
Press the = or ; button on the
steering wheel to select the
Sett. menu.
X
Press the : or 9 button to select the
Convenience submenu.
X
Press a to confirm.
X
Press the : or 9 button to select the
Auto. Mirror Folding
function.
If the Auto. Mirror Folding
function is
activated, the vehicle's exterior mirror is
displayed in red in the multifunction
display.
X
Press the a button to save the setting.
If you have switched the
Auto. Mirror
Folding function on and you fold the exterior
mirrors in using the button on the door
(Y page 104), they will not fold out
automatically. The exterior mirrors can then
only be folded out using the button on the
door.
Restoring the factory settings
X
Press the = or ; button on the
steering wheel to select the
Sett. menu.
X
Press the : or 9 button to select the
Factory Setting submenu.
X
Press a to confirm.
The
Reset All Settings? message
appears.
X
Press the : or 9 button to select
No
or Yes.
X
Press the a button to confirm the
selection.
If you have selected
Yes, the multifunction
display shows a confirmation message.
For safety reasons, the
Day Lights
function
in the
Lights submenu is only reset if the
vehicle is stationary.
AMG menu in AMG vehicles
AMG displays
X
Press = or ; on the steering wheel
to select the
AMG
menu.
:
Digital speedometer
;
Gear indicator
212
Menus and submenus
On-board computer and displays
=
Upshift indicator
?
Engine oil temperature
A
Coolant temperature
Upshift indicator
UP = indicates that the
engine has reached the overrevving range
when in the manual gearshift program.
Upshift indicator
UP
= fades out other
messages until you have shifted up.
If the engine oil temperature is below 176 ‡
(80 †) the oil temperature is shown in blue.
Avoid driving at full engine output during this
time.
SETUP
SETUP shows the drive program, the ESP
®
(Electronic Stability Program) mode and the
SPORT handling mode.
X
Press = or ; on the steering wheel
to select the
AMG menu.
X
Press the 9 button repeatedly until
SETUP is displayed.
:
Drive program (
C/SS+/M)
;
ESP
®
mode (
ON
/OFF) or SPORT handling
mode (
SPORT
)
RACETIMER
Displaying and starting RACETIMER
The RACETIMER is only intended for use on a
closed race circuit. Do not use the function
on public roads.
You can use the RACETIMER to store lap
times.
X
Press = or ; on the steering wheel
to select the
AMG menu.
X
Press the 9 button repeatedly until the
RACETIMER is shown.
i
If the RACETIMER is selected, the =
and ; buttons cannot be used to call up
the menu bar.
:
Lap
;
RACETIMER
You can start the RACETIMER when the
engine is running or if the SmartKey is in
position 2 in the ignition lock.
X
To start: press the a button to start the
RACETIMER.
Displaying the intermediate time
X
Press the = or ; button to select
Interm. Time.
X
Press a to confirm.
The intermediate time is displayed for five
seconds.
Starting a new lap
X
Press a to confirm
New Lap.
Menus and submenus
213
On-board computer and displays
Z
:
RACETIMER
;
Fastest lap time (bestlap)
=
Lap
i
It is possible to store a maximum of
sixteen laps. The 16th lap can only be
completed with
Finish Lap
.
Stopping the RACETIMER
X
Press the % button on the steering
wheel.
X
Press a to confirm
Yes.
The RACETIMER interrupts timing when you
stop the vehicle and turn the SmartKey to
position 1 in the ignition lock. If you turn the
key to position 2 or 3 and then press a to
confirm
Start
, timing is continued.
Resetting the current lap
X
Stop the RACETIMER.
X
Press the = or ; buttonto select
Reset Lap.
X
Press a to reset the lap time to "0".
Deleting all laps
If you switch off the engine, the RACETIMER
is reset to "0" after 30 seconds. All laps are
deleted.
You cannot delete individual stored laps. If
you have stopped 16 laps, the current lap
does not have to be reset.
X
Reset the current lap.
X
Press a to confirm
Reset
.
Reset Race Timer? appears in the
multifunction display.
X
Press the : button to select
Yes and
press the a button to confirm.
All laps are deleted.
Overall statistics
This function is shown if you have stored at
least one lap and stopped the RACETIMER.
X
Press = or ; on the steering wheel
to select the
AMG menu.
X
Press the 9 button repeatedly until the
overall evaluation is shown.
:
RACETIMER overall evaluation
;
Total time driven
=
Average speed
?
Distance covered
A
Maximum speed
214
Menus and submenus
On-board computer and displays
Lap statistics
This function is only available if you have
stored at least two laps and have stopped the
RACETIMER.
X
Press = or ; on the steering wheel
to selectthe
AMG
menu.
X
Press the 9 button repeatedly until the
lap evaluation is shown.
Each lap is shown in a separate submenu.
The fastest lap is indicated by flashing
symbol :.
:
Lap
;
Lap time
=
Average lap speed
?
Lap length
A
Top speed during lap
X
Press the 9 or : button to select a
different lap evaluation.
Menus and submenus
215
On-board computer and displays
Z

Related Topics

On-board computer and displays
Useful information Important safety notes Displays and operation Display messages Warning and indicator lamps in the instrument cluster

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot