2025-2026 Mercedes G Class SUV Maintenance and care User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Maintenance and care for Your Mercedes G Class SUV Fifth Generation (2025-2026)

Maintenance and care
This interactive PDF works like a website – tap or click a button to jump straight to where you want to go.
You can return here at any time via the navigation bar at the top left.
ASSYST PLUS service interval display
569
Maintenance Management 571
Telediagnostics 572
Engine compartment 573
Cleaning and care 579
G-Class - Owner's Manual
Maintenance and care
F465 0034 02
569
ASSYST PLUS service interval display
Function of the ASSYST PLUS service interval
display
The ASSYST PLUS service interval display on the driver's display informs you
of the next regular service due date.
Depending on the operating conditions of the vehicle, the remaining time or
distance until the next service due date will be displayed.
You can hide this service display using the back button G on the steering
wheel.
You can obtain information concerning the servicing of your vehicle
from a qualified specialist workshop, e.g. a Mercedes-Benz service centre
(/page99).
Displaying the service due date
Driver display:
4
Service
The next service due date is displayed.
#
To exit the display: press the back button G on the steering wheel.
Information on regular service work
*
NOTE
Premature wear through failure to observe service due dates
Service work which is not carried out at the right time or incompletely
can lead to increased wear and damage to the vehicle.
#
Observe the specified service intervals. If there are any uncer‐
tainties regarding the service due date, forexample if the bat‐
tery is disconnected, operating conditions are difficult, etc.,
contact a qualified specialist workshop.
#
Have the prescribed service work carried out at a qualified
specialist workshop.
G-Class - Owner's Manual
Maintenance and care ASSYST PLUS service interval display
F465 0034 02
570
*
NOTE
Irreparable damage to the high-voltage battery due to mainte‐
nance work not being carried out
The high-voltage battery is subject to wear. Maintenance work which is
not carried out in time can lead to irreparable damage to the high-volt‐
age battery.
#
Always observe the warning messages about the high-voltage
battery and immediately consult a qualified specialist work‐
shop.
#
Have the necessary maintenance work on the high-voltage
battery carried out at a qualified specialist workshop.
Notes on special service requirements
The prescribed service interval is based on normal operation of the vehicle.
Have the maintenance work carried out more often than prescribed if operat‐
ing conditions are difficult or the vehicle is subject to increased stress. This
is the case for frequent operation in mountainous terrain or on poor road
surfaces, for example.
In these or similar operating conditions, have the interior air filter changed
more frequently. Check the tyres more frequently if the vehicle is operated
under increased stress. Further information can be obtained at a qualified
specialist workshop.
The ASSYST PLUS service interval display is only an aid. It is the responsibility
of the driver of the vehicle to have maintenance work carried out more often
than prescribed due to actual operating conditions and/or stresses.
Battery disconnection periods
The ASSYST PLUS service interval display can calculate the service due date
only when the battery is connected.
#
Display and note down the service due date on the driver display before
disconnecting the battery (/page569).
#
The period with disconnected battery is not taken into account by
ASSYST PLUS. Deduct the period with disconnected battery from the
time indicated on the driver display.
R
The calculated date serves as a new service due date.
R
The service interval for distance before service due date (km) is
not affected in this regard.
G-Class - Owner's Manual
Maintenance and care ASSYST PLUS service interval display
F465 0034 02
571
Maintenance Management
Notes about Maintenance Management
If the Maintenance Management service is activated, relevant data is automat‐
ically transferred to the Mercedes-Benz customer centre.
The customer centre transmits the data to the service partner that you have
entered on the Mercedes-Benz website at: https://www.mer. You will
then receive individual recommendations regarding the maintenance of your
vehicle.
%
The calculation of the optimal transmission time of the mainte‐
nance request to the service partner is subject to technical limi‐
tations that may cause the maintenance recommendation to be
perceived as too early or too late or not to be made at all. In this
case, you can conveniently arrange a maintenance appointment
with the customer centre via the maintenance reminder in the
multimedia system.
%
Maintenance Management and the maintenance reminder in the
multimedia system are not available in every country. Contact a
Mercedes-Benz service centre to find out whether this function
is available in your country.
Data transferred when using Maintenance
Management
When the service is activated, relevant data is automatically transferred to
determine the required scope of maintenance as well as fault detection and
fault rectification.
Details on data transmission can be found in the data protection notes for
Mercedes-Benz Support. These can be found at: https://www.mer
under "My Account", "Privacy & Legal".
%
Maintenance Management and the maintenance reminder in the
multimedia system are not available in every country.
G-Class - Owner's Manual
Maintenance and care Maintenance Management
F465 0034 02
572
Telediagnostics
Notes about Telediagnosis
%
This service is not available in all countries.
The vehicle can detect if certain wear parts need to be replaced or if mal‐
functions have occurred in vehicle systems. If the Telediagnosis service is
activated, relevant data is automatically transmitted to the manufacturer. If
fault conditions are detected by the vehicle system self-diagnosis, the system
transmits recommendations for action to the Mercedes-Benz customer centre
depending on the fault detected. The customer centre transmits the data to
the service partner that you have entered on the Mercedes-Benz website at:
https://www..
For selected faults, the notification that a malfunction has been detected may
appear in the multimedia system with a request to contact the Mercedes-Benz
Customer Centre. From this message, a call can be made directly to the cus‐
tomer centre for assistance.
%
The transmission of a notification to the multimedia system
depends on the country, vehicle model and equipment and
requires a fast data connection, over which the service provider
has no influence.
%
Reliable fault detection is subject to technical limitations. There‐
fore, only a limited selection of faults can be detected and rec‐
ommendations for action transmitted to the customer centre and
the service partners. Mercedes-BenzAG is continuously working
on the expansion of this service. The fault detection depends on
the country, vehicle model and equipment.
Data transferred when using Telediagnosis
When the service is activated, relevant data is automatically transferred to
determine the required scope of maintenance as well as fault detection and
fault rectification.
Details on data transmission can be found in the data protection notes for
Mercedes-Benz Support. These can be found at: https://www.mer
under "My Account", "Privacy & Legal".
%
The scope of the transmitted data depends on the vehicle model
and its equipment. For technical reasons, not all data is available
at all times.
G-Class - Owner's Manual
Maintenance and care Telediagnostics
F465 0034 02
573
Engine compartment
Opening and closing the bonnet
&
DANGER
Risk of fatal injuries when carrying out maintenance work during
the charging process
During the charging process, the high-voltage on-board electrical sys‐
tem is under high voltage.
#
Do not perform any maintenance work during the charging
process.
&
WARNING
Risk of accident due to driving with the bonnet unlocked
The bonnet may open and block your view.
#
Never release the bonnet when driving.
#
Before every trip, ensure that the engine bonnet is locked.
&
WARNING
Risk of accident and injury when opening and closing the bonnet
The bonnet may suddenly drop into the end position.
There is a risk of injury for anyone in the engine bonnet's range of
movement.
#
Do not open or close the bonnet if there is a person in the
bonnet's range of movement.
&
WARNING
Risk of injury due to overheated vehicle
IF YOU OPEN THE BONNET IN THE EVENT OF AN OVERHEATED
VEHICLE OR FIRE IN THE ENGINE COMPARTMENT, THE FOLLOWING
SITUATIONS MAY OCCUR:
R
You may come into contact with hot gases.
R
You may come into contact with other escaping hot operating
fluids.
#
In the event of overheating or fire in the engine compartment,
keep the bonnet closed and call the fire service.
#
Allow the overheated vehicle to cool down first if you need to
open the bonnet.
G-Class - Owner's Manual
Maintenance and care Engine compartment
F465 0034 02
574
&
WARNING
Risk of injury due to moving parts
Components in the engine compartment may continue to run or start
unexpectedly even when the drive system is switched off.
Observe the following if you must open the bonnet:
#
Switch off the vehicle.
#
Never touch the danger zones surrounding moving compo‐
nents, e.g. the rotation area of the fan.
#
Remove jewellery and watches.
#
Keep items of clothing and hair away from moving parts.
&
WARNING
Risk of burns from hot components in the engine compartment
Certain components in the engine compartment can be very hot, e.g.
the drive system and the cooler.
#
Allow the drive system to cool down and touch only the com‐
ponents described below.
&
WARNING
Risk of injury from using the windscreen wipers when the bonnet
is open
If the windscreen wipers start moving when the bonnet is open, you
could be trapped by the wiper linkage.
#
Always switch off the windscreen wipers and the vehicle first if
you need to open the bonnet.
OPENING THE BONNET
#
To release the bonnet, pull on handle 1.
G-Class - Owner's Manual
Maintenance and care Engine compartment
F465 0034 02
575
#
Push handle 1 of the bonnet catch upwards and lift the bonnet by
approximately 40 cm.
The bonnet will be opened and held open automatically by the pneu‐
matic spring.
CLOSING THE BONNET
#
Lower the bonnet until the bonnet catch engages.
#
Then, press the bonnet firmly into the lock with both hands until it is
completely closed.
#
If the bonnet can still be lifted slightly, open the bonnet again and repeat
the previous step until it engages correctly.
Checking the coolant level
&
DANGER
Risk of fatal injuries when carrying out maintenance work during
the charging process
During the charging process, the high-voltage on-board electrical sys‐
tem is under high voltage.
#
Do not perform any maintenance work during the charging
process.
&
WARNING
Risk of injury due to overheated vehicle
IF YOU OPEN THE BONNET IN THE EVENT OF AN OVERHEATED
VEHICLE OR FIRE IN THE ENGINE COMPARTMENT, THE FOLLOWING
SITUATIONS MAY OCCUR:
R
You may come into contact with hot gases.
R
You may come into contact with other escaping hot operating
fluids.
#
In the event of overheating or fire in the engine compartment,
keep the bonnet closed and call the fire service.
#
Allow the overheated vehicle to cool down first if you need to
open the bonnet.
G-Class - Owner's Manual
Maintenance and care Engine compartment
F465 0034 02
576
&
WARNING
Risk of injury due to moving parts
Components in the engine compartment may continue to run or start
unexpectedly even when the drive system is switched off.
Observe the following if you must open the bonnet:
#
Switch off the vehicle.
#
Never touch the danger zones surrounding moving compo‐
nents, e.g. the rotation area of the fan.
#
Remove jewellery and watches.
#
Keep items of clothing and hair away from moving parts.
&
WARNING
Risk of scalding from hot coolant
You may scald yourself if you open the cap when the drive system is at
normal operating temperature.
#
Allow the drive system to cool down before opening the cap.
#
When opening the cap, wear protective gloves and safety
glasses.
#
Open the cap slowly to release pressure.
#
Park the vehicle on a level surface.
#
Check the coolant temperature display on the driver display
(/page392).
The coolant temperature must be below 40°C.
#
Slowly turn cap 1 anti-clockwise to release overpressure.
#
Continue turning cap 1 anti-clockwise and remove it.
#
If the coolant level is below the marker bar 2, refill with coolant that
has been approved for Mercedes-Benz.
%
Further information on coolant (/page706).
G-Class - Owner's Manual
Maintenance and care Engine compartment
F465 0034 02
577
Topping up the windscreen washer system
&
DANGER
Risk of fatal injuries when carrying out maintenance work during
the charging process
During the charging process, the high-voltage on-board electrical sys‐
tem is under high voltage.
#
Do not perform any maintenance work during the charging
process.
&
WARNING
Risk of injury due to overheated vehicle
IF YOU OPEN THE BONNET IN THE EVENT OF AN OVERHEATED
VEHICLE OR FIRE IN THE ENGINE COMPARTMENT, THE FOLLOWING
SITUATIONS MAY OCCUR:
R
You may come into contact with hot gases.
R
You may come into contact with other escaping hot operating
fluids.
#
In the event of overheating or fire in the engine compartment,
keep the bonnet closed and call the fire service.
#
Allow the overheated vehicle to cool down first if you need to
open the bonnet.
&
WARNING
Risk of injury due to moving parts
Components in the engine compartment may continue to run or start
unexpectedly even when the drive system is switched off.
Observe the following if you must open the bonnet:
#
Switch off the vehicle.
#
Never touch the danger zones surrounding moving compo‐
nents, e.g. the rotation area of the fan.
#
Remove jewellery and watches.
#
Keep items of clothing and hair away from moving parts.
&
WARNING
Risk of burns from hot components in the engine compartment
Certain components in the engine compartment can be very hot, e.g.
the drive system and the cooler.
#
Allow the drive system to cool down and touch only the com‐
ponents described below.
G-Class - Owner's Manual
Maintenance and care Engine compartment
F465 0034 02
578
&
WARNING
Risk of fire and injury from windscreen washer concentrate
Windscreen washer concentrate is highly flammable.
#
Avoid fire, naked flames, smoking and the creation of sparks
when using windscreen washer concentrate.
#
Turn cap 1 anti-clockwise and remove it.
#
Top up the washer fluid.
#
Replace cap 1 and turn it clockwise as far as it will go.
Keeping the air/water duct free
#
Keep the area between the bonnet and the windscreen free of deposits,
e.g. ice, snow or leaves.
G-Class - Owner's Manual
Maintenance and care Engine compartment
F465 0034 02
579
Cleaning and care
Information on washing the vehicle in a car
wash
&
WARNING
Risk of an accident due to reduced braking power after washing
the vehicle
Braking efficiency is reduced after washing the vehicle.
#
After the vehicle has been washed, brake carefully while pay‐
ing attention to the traffic conditions until braking power has
been fully restored.
*
NOTE
Damage from automatic braking
THE VEHICLE WILL BRAKE AUTONOMOUSLY IN CERTAIN SITUA‐
TIONS IF THE FOLLOWING FUNCTIONS ARE SWITCHED ON:
R
Active Brake Assist
R
Active Distance Assist DISTRONIC
R
HOLD function
R
Active Parking Assist
To avoid damage to the vehicle, switch these systems off e.g. before
towing it or in a car wash.
*
NOTE
Damage due to unsuitable car wash
#
Before driving into a car wash make sure that the car wash is
suitable for the vehicle dimensions.
#
Ensure there is sufficient ground clearance between the
underbody and the guide rails of the car wash.
#
Ensure that the clearance width of the car wash, in particular
the width of the guide rails, is sufficient.
G-Class - Owner's Manual
Maintenance and care Cleaning and care
F465 0034 02
580
TO AVOID DAMAGE TO YOUR VEHICLE WHEN USING A CAR WASH,
ENSURE THE FOLLOWING BEFOREHAND:
R
Active Distance Assist DISTRONIC is switched off.
R
The HOLD function is switched off.
R
The 360° camera or the reversing camera is switched off.
R
The side windows and sliding sunroof are completely closed.
R
The outside mirrors are retracted.
R
The blower for the ventilation and heating is switched off.
R
The windscreen wiper switch is in position g.
R
Vehicles with KEYLESS-GO: The key is a minimum distance of 3m away
from the vehicle. Otherwise a door may lock and unlock unintentionally.
R
For car washes with conveyor systems:
-
Neutral gear i is engaged.
-
If you leave the vehicle while it is being washed, ensure the key is
located in the vehicle. The park position j is otherwise automati‐
cally engaged.
%
Removing the wax from the windscreen and the wiper rubber
after washing the vehicle will help to avoid smearing and reduce
wiper noise.
Car wash mode
In car wash mode, the vehicle is prepared for driving into an automatic
car wash. Car wash mode can be activated up to a speed of 20km/h
(/page581).
WHEN CAR WASH MODE IS ACTIVATED, THE
CAR WASH MODE ACTIVE MES‐
SAGE WILL APPEAR ON THE DRIVER DISPLAY. THE FOLLOWING ADJUST‐
MENTS WILL BE MADE:
R
The outside mirrors will be folded in.
R
To prevent the windscreen washer system from starting up automatically,
the rain sensor will be deactivated.
R
Air-recirculation mode will be activated.
R
The rear window wiper will be deactivated.
R
The windows and the sliding sunroof will be closed.
R
Parking Assist PARKTRONIC will be deactivated.
R
Vehicles with 360° camera: the front image will be activated after
approximately eight seconds.
If one of the settings cannot be selected, this is displayed by a % behind
the respective setting.
Pressing Switch off will cancel car wash mode. Car wash mode will automati‐
cally be deactivated above a speed of 20km/h.
You can also switch off car wash mode via the MBUX multimedia system
(/page581).
THE FOLLOWING SETTINGS WILL BE RESET WHEN CAR WASH MODE IS
DEACTIVATED:
R
The outside mirrors will be folded out.
R
The rain sensor will be activated.
R
Air-recirculation mode will be deactivated.
R
The windows and the sliding sunroof will remain closed.
R
The rear window wiper will be activated.
G-Class - Owner's Manual
Maintenance and care Cleaning and care
F465 0034 02
581
R
Parking Assist PARKTRONIC will be reset to the previously selected set‐
ting.
R
Vehicles with 360° camera: the front image will be deactivated at
speeds above 18km/h.
Switching car wash mode on/off
Requirements:
R
The vehicle is stationary.
R
The vehicle is switched on.
Multimedia system:
4
©
5
Settings
5
Vehicle
5
Driving
ACTIVATING CAR WASH MODE
#
Select Car wash mode.
#
Select Activate.
If one of the settings cannot be selected, this will be shown by a % next to
the respective setting.
%
For an overview of the settings configured when you activate car
wash mode (/page580).
DEACTIVATING CAR WASH MODE
#
Select Switch off.
The settings of car wash mode will be reset.
%
Car wash mode will be automatically deactivated as soon as your
speed exceeds 20km/h.
Information on using a high-pressure cleaner
&
WARNING
Risk of an accident when using high-pressure cleaners with round-
spray nozzles
The water jet can cause externally invisible damage.
Components damaged in this way may unexpectedly fail.
#
Do not use a high-pressure cleaner with round-spray noz‐
zles.
#
Have damaged tyres or chassis parts replaced immediately.
TO AVOID DAMAGE TO YOUR VEHICLE, OBSERVE THE FOLLOWING WHEN
USING A HIGH-PRESSURE CLEANER:
R
Vehicles with KEYLESS-GO: The key is at a minimum distance of 3m
away from the vehicle. Otherwise the doors could lock and unlock unin‐
tentionally.
R
Maintain a distance of at least 30cm to the vehicle.
R
Vehicles with decorative foil: Parts of your vehicle are covered with
a decorative foil. Maintain a distance of at least 70cm between the foil-
covered parts of the vehicle and the nozzle of the high-pressure cleaner.
Move the nozzle of the high-pressure cleaner around while cleaning. The
water temperature of the high-pressure cleaner must not exceed 60°C.
G-Class - Owner's Manual
Maintenance and care Cleaning and care
F465 0034 02
582
R
Observe the information on the correct distance in the equipment manu‐
facturer's operating instructions.
R
Do not direct the nozzle of the high-pressure cleaner directly at sensitive
parts, e.g. tyres, gaps, electrical components, batteries, illuminants or
louvres.
Washing the vehicle by hand
*
NOTE
Damage to the wheel arch flares and bumpers if used as a step
The wheel arch flares and bumpers can be damaged or become
detached from the vehicle if you use them as a step.
#
Only use the two steps indicated on the rear bumper.
Observe the relevant legal requirements (for example in some countries, wash‐
ing by hand is permitted only in specially designated wash bays).
#
Use a mild cleaning agent, e.g. car shampoo.
#
Do not use acidic cleaning agents.
#
Wash the vehicle with lukewarm water using a soft car sponge. When
doing so, do not expose the vehicle to direct sunlight.
#
Carefully hose the vehicle off with water and dry using a chamois.
%
Observe the notes on the care of car parts (/page584).
Notes on paintwork/matt finish paintwork
care
To avoid damaging the paintwork and interfering with the driving assistance
systems, please observe the following notes:
PAINT
R
Insect remains: soak with insect remover and rinse off the treated areas
afterwards.
R
Bird droppings: soak with water and rinse off afterwards.
R
Tree resin, oils, fuels and greases: remove by rubbing gently with a cloth
soaked in petroleum ether or lighter fluid.
R
Coolant and brake fluid: remove with a damp cloth and clean water.
R
Tar stains: use tar remover.
R
Wax: use silicone remover.
R
Do not attach stickers, foil or similar materials. Only have foil attached to
the bumper at a qualified specialist workshop.
R
Remove dirt immediately, where possible. Do not use acid solutions and
acidic cleaners.
MATT FINISH
R
Only use care products approved for Mercedes-Benz.
R
Do not attach stickers, foils or similar materials. Only have foil attached
to the bumper at a qualified specialist workshop.
R
Do not polish the vehicle and light-alloy wheels.
R
Only use car washes that correspond to the latest engineering standards.
R
Do not use car wash programmes with a final hot wax treatment.
R
Do not use paint cleaners, buffing or polishing products, gloss preserv‐
ers, .
G-Class - Owner's Manual
Maintenance and care Cleaning and care
F465 0034 02
583
IN THE EVENT OF PAINTWORK DAMAGE:
R
Always have paintwork repairs carried out at a qualified specialist work‐
shop.
R
Make sure the radar sensors are working (/page320).
Notes on cleaning decorative foils
Observe the "Notes on paintwork / matt finish paintwork care" (/page582).
They also apply to matt decorative films.
Observe the notes on cleaning decorative films to avoid damage.
CLEANING
R
When cleaning with the high-pressure cleaner, maintain a distance of at
least 70 cm between the foil-covered parts of the vehicle and the nozzle
of the high-pressure cleaner.
R
For cleaning, use plenty of water and a mild cleaning agent without addi‐
tives or abrasive substances (e.g. a car shampoo approved for Mercedes-
Benz).
R
Do not use acidic cleaning agents.
R
Remove dirt as soon as possible. Avoid rubbing too hard in order not to
damage the decorative film irreparably.
R
If there is dirt on the finish or if the decorative film is dull: use the paint
cleaner recommended and approved for Mercedes-Benz.
R
Insect remains: Soak with insect remover and rinse off the treated areas
afterwards.
R
Bird droppings: Soak with water and rinse off afterwards.
R
To prevent water stains, dry a film-wrapped vehicle with a soft, absorb‐
ent cloth after every car wash.
AVOIDING DAMAGE TO THE DECORATIVE FILM
R
The service life and colouring of decorative films are impaired by:
-
Sunlight
-
Temperature (e.g. hot air blower)
-
Weather conditions
-
Stone chippings and dirt
-
Chemical cleaning agents
-
Oily products
R
Do not use polish on matt decorative film. Polishing will have the effect
of shining the film-wrapped surface.
R
Do not treat matt or structured decorative films with wax. Permanent
stains may occur.
Scratches, corrosive deposits, areas affected by corrosion and damage caused
by incorrect care cannot always be completely repaired. In this case, contact a
qualified specialist workshop.
You can obtain more information on care and cleaning agents from the manu‐
facturer.
In the case of film-wrapped surfaces, visual differences may occur between
the surfaces that were not protected by a decorative film after a decorative
film has been removed.
%
Have work or repairs to decorative films carried out at a qualified
specialist workshop (e.g. at a Mercedes-Benz Service Centre).
G-Class - Owner's Manual
Maintenance and care Cleaning and care
F465 0034 02
584
Information on window films
*
NOTE
Damage to electronic components due to excess fluids
When window films have been retrofitted, fluids such as cleaning
agents or water may run down and get behind trim parts of the vehicle
interior and cause damage to electronic components.
#
Use cleaning agents as sparingly as possible.
#
Immediately absorb any excess fluids.
Notes on car parts cleaning and care
&
WARNING
Risk of entrapment if the windscreen wipers are switched on while
the windscreen is being cleaned
If the windscreen wipers are set in motion while you are cleaning the
windscreen or wiper blades, you can be trapped by the wiper arm.
#
Always switch off the windscreen wipers and the drive system
before cleaning the windscreen or wiper blades.
*
NOTE
Damage due to use of acidic cleaning agents
#
Do not use acidic cleaning agents. Otherwise, the surfaces
could be damaged.
To avoid damage to the vehicle, observe the notes on cleaning and care of the
following car parts:
WINDOWS
*
NOTE
Damage to electronic components due to excess fluids
When cleaning the windows from the inside, fluids such as cleaning
agents or water may run down and get behind trim parts of the vehicle
interior and cause damage to electronic components.
#
Use cleaning agents as sparingly as possible.
#
Immediately absorb any excess fluids.
R
Clean the windows on the inside and outside with a damp cloth and with
a cleaning agent recommended for Mercedes-Benz.
R
Do not use dry cloths or abrasive or solvent-based cleaning agents to
clean the insides of windows.
%
After changing the wiper blades or treating the vehicle with
wax, clean the windscreen thoroughly with cleaning agents rec‐
ommended for Mercedes-Benz. Failure to observe the applica‐
tion instructions may result in damage, smear marks or dazzling
spots.
%
Remove external misting or dirt on the windscreen in front of
the multifunction camera. Otherwise, driving systems and driving
safety systems may be impaired or unavailable (/page320).
G-Class - Owner's Manual
Maintenance and care Cleaning and care
F465 0034 02
585
WHEELS AND RIMS
R
Use water and acid-free wheel cleaners.
R
Do not use acidic wheel cleaners to remove brake dust. This could dam‐
age wheel bolts and brake components.
R
To avoid corrosion of the brake discs and pads, drive the vehicle for a
few minutes after cleaning before parking it. The brake discs and brake
linings will warm up and dry out.
EXTERIOR LIGHTING
R
Clean the lenses with a wet sponge and mild cleaning agent (e.g. car
shampoo).
R
Use only cleaning agents or cleaning cloths that are suitable for plastic
lenses.
VEHICLE SOCKET (HIGH-VOLTAGE BATTERY)
R
Use clean water and a soft cloth to clean the vehicle socket.
R
Do not use high-pressure cleaners or cleaning agents (such as soap).
SENSORS
R
Clean the sensors in the front and rear part of the vehicle with car
shampoo, plenty of water and a soft cloth (/page320).
R
When using a high-pressure cleaner, maintain a minimum distance of
30cm.
Notes on interior care
&
WARNING
Risk of injury from plastic parts breaking off after the use of sol‐
vent-based care products
Care and cleaning products containing solvents can cause surfaces in
the cockpit to become porous. When the airbags are deployed, plastic
parts may break away.
#
Do not use any care or cleaning products containing solvents
to clean the cockpit.
&
WARNING
Risk of injury or fatal injuries from bleached seat belts
Bleaching or dyeing seat belts can severely weaken them.
This can, for example, cause seat belts to tear or fail in an accident.
#
Never bleach or dye seat belts.
G-Class - Owner's Manual
Maintenance and care Cleaning and care
F465 0034 02
586
*
NOTE
Property damage due to disinfectants
The interior includes a number of sensitive surfaces such as displays,
plastics and leather.
Disinfectants can contain alcohol and other substances that penetrate
and damage surfaces. Technology behind buttons and displays can also
be damaged.
#
Do not use disinfectant on interior surfaces.
To avoid damage to the vehicle, observe the following notes on cleaning and
care:
SEAT BELTS
R
Clean with lukewarm, soapy water.
R
Do not use chemical cleaning agents.
R
Do not dry by heating to more than 80 °C or exposing to direct sunlight.
DISPLAY
R
Switch off the display and allow it to cool.
R
Clean the surface carefully with a microfibre cloth and a suitable display
care product (TFT LCD).
R
Do not use any other agents.
PLASTIC TRIM
R
Clean with a damp microfibre cloth.
R
If it is very dirty, use a cleaning agent recommended for Mercedes-Benz.
R
Do not attach stickers, plastic film or similar materials.
R
Do not allow cosmetics, insect repellent or sun cream to come into
contact with the plastic trim.
GENUINE WOOD AND TRIM ELEMENTS
R
Clean with a microfibre cloth.
R
Black piano-lacquer look: clean with a damp cloth and soapy water.
R
If it is very dirty, use a cleaning agent recommended for Mercedes-Benz.
R
Do not use solvent-based cleaning agents, polishes or waxes.
HEADLINER
R
Clean with a brush or dry shampoo.
CARPET
R
Use a carpets and textiles cleaning agent recommended for Mercedes-
Benz.
IMITATION LEATHER STEERING WHEEL
R
Clean the entire steering wheel with a damp cotton cloth and a 1% soap
solution. Do not spot clean.
R
Use cleaning and care products recommended for Mercedes-Benz.
R
Do not use a microfibre cloth.
R
Do not use oil-based cleaning and care products.
STEERING WHEEL MADE OF GENUINE LEATHER OR DINAMICA
*
NOTE
Damage caused by wrong cleaners
#
Do not use solvent-based cleaning agents such as tar remover
or wheel cleaner; neither should you use polishes or waxes.
Otherwise you may damage the finish.
R
Clean with a damp cloth and a 1% soap solution and then wipe with a
dry cloth.
R
If it is very dirty, use a cleaning agent recommended for Mercedes-Benz.
R
Leather care: use a leather care agent recommended for Mercedes-Benz.
G-Class - Owner's Manual
Maintenance and care Cleaning and care
F465 0034 02
587
R
Do not allow the leather to become too damp.
R
Do not use a microfibre cloth.
%
Leather is a natural product. It has natural surface characteris‐
tics, such as differences in structure, marks caused by growth
and injury or subtle colour differences. These surface charac‐
teristics are particular to leather, and are not material defects.
Leather is also subject to a natural ageing process, which
changes the surface characteristics.
GENUINE LEATHER SEAT COVERS
R
Vacuum up dirt suchas crumbs or dust and then clean the seat covers
with a damp cotton cloth and wipe down with a dry cloth. Regularly clean
the seat covers.
R
If they are very dirty, use an aftercare leather care agent recommended
for Mercedes-Benz.
R
Leather care: use a leather care agent recommended for Mercedes-Benz.
R
Do not use a microfibre cloth.
R
Do not allow the leather to become too damp.
R
Do not use oil-based cleaning and care products.
%
Leather is a natural product. It has natural surface characteris‐
tics, such as differences in structure, marks caused by growth
and injury or subtle colour differences. These surface charac‐
teristics are particular to leather, and are not material defects.
Leather is also subject to a natural ageing process, which
changes the surface characteristics.
Waves or wrinkling in the seat cover may occur due to the stress
on the seat; this is caused by the natural leather material.
Regular cleaning and care of the leather will reduce dirt build-up,
wear marks and ageing damage and thus significantly extend its
life span. Clothing that can leave stains (e.g. jeans) may discolour
the leather.
IMITATION LEATHER SEAT COVERS
R
Vacuum up dirt suchas crumbs or dust and then use a damp cotton cloth
and a 1% soap solution to clean the entire seat cover. Do not spot clean.
R
Use cleaning and care products recommended for Mercedes-Benz.
R
Do not use a microfibre cloth.
R
Do not use oil-based cleaning and care products.
G-Class - Owner's Manual
Maintenance and care Cleaning and care
F465 0034 02

Related Topics

ASSYST PLUS service interval display Maintenance Management Telediagnostics Engine compartment Cleaning and care

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot