Get Lights and Switches Guide for Mg HS SUV Second Generation (2024-2026)

BRIEF INTRODUCTION TO VEHICLE FUNCTIONS

Lights and Switches

Headlamp

Master Light Switch

AUTO Lamp Off

AUTO Lamp

With the Start switch in ACC position, the AUTO lighting

system is active by default (position 1). The system will

automatically switch on or off the side lamps and switch

backlights according to the intensity of current ambient

light.

With the Start switch in ON/RUNNING/READY position,

the AUTO lighting system will automatically switch on

or off the low beams, side lamps and switch backlights

according to the intensity of current ambient light.

AUTO Lamp

Side Lamp/Switch Backlights

When the Start switch is in the ACC position, toggle the

master light cycle switch to position 2 to switch on the side

lamps/switch backlights.

Side Lamp and Switch Backlights

70

BRIEF INTRODUCTION TO VEHICLE FUNCTIONS

When the Start switch is in the ON/RUNNING/READY

Daytime Running Lamp

position, toggle the master light cycle switch to position

2 to switch on the daytime running lamps, side lamps and

switch backlights.

The daytime running lamps turn on automatically when

the Start switch is in the ON/RUNNING/READY position.

When the low beam is turned on, the daytime running lamp

goes out automatically.

2

For some models, when the environment is dark and the

gear is not in P, the low beam will automatically light up.

Welcome Light^*

With the Start switch in the OFF position, if the side lamps

stay on when the driver's door is open, the system will

issue an alarm.

When the vehicle is unlocked, the system will automatically

turn on corresponding external lamps according to the

intensity of the current ambient light to show the welcome

effect. The welcome light function can be set in the Vehicle

Settings interface on the entertainment display.

Headlamp

When the Start switch is in the ON/RUNNING/READY

position, toggle the master light cycle switch to position 3

to switch on the low beams, side lamps/switch backlights.

Follow Me Home

When the power system is turned off, the light lever switch

is in the AUTO position and the AUTO lamp is turned on,

The Follow Me Home function will be enabled and the low

beams and side lamps will illuminate for a period of time and

then automatically turn off. Follow Me Home function can

be set in the Vehicle Settings interface on the entertainment

display.

AUTO Lamp Off

Toggle the master light switch to position 4 to turn off

the AUTO lamp. When released, the switch automatically

returns to position 1.

For some models, when the environment is dark and the

gear is not in P, the low beam will automatically light up.

71

BRIEF INTRODUCTION TO VEHICLE FUNCTIONS

Headlamp Levelling

Location

Load

All the seats occupied plus an

evenly distributed load in the

loadspace

2

Driver only, plus an evenly

distributed load in the loadspace

3

The headlamp levelling can be adjusted as per the following

table according to the vehicle load.

Location

Load

Driver or driver

passenger

&

front

0

All the seats occupied with no

load in the loadspace.

1

72

BRIEF INTRODUCTION TO VEHICLE FUNCTIONS

Switching between High Beam and Low

Beam Headlamps

illuminates. Push or pull the lever ( 1 or 2 ) once again to

switch to low beams.

Take care not to dazzle oncoming vehicles

when switching between the main and

dipped beams.

High Beam Flash

2

To brieﬂy ﬂash the high beam, pull the lever towards the

steering wheel and release it several times.

Smart High Beam System

The Automatic High Beam serves only as an

auxiliary function. The driver must check

the status of the front lamps and turn on

the front lamps when necessary.

When the Start switch is in the ON/RUNNING/READY

position and the low beams illuminate, push the light lever

switch (1) towards the instrument panel to turn on the

high beams and the high beam indicator on the instrument

73

BRIEF INTRODUCTION TO VEHICLE FUNCTIONS

The Automatic High Beam may not operate

The smart high beam system can detect the light intensity

of the vehicle ahead by the front view camera and the high

beams can be turned on or off once certain conditions

are met. When the smart high beam system is enabled,

the smart high beam indicator on the instrument panel will

illuminate.

normally in the following cases, operation

is not limited to the following and so the

main and dipped beams should be switched

manually:

•

The windscreen is dirty, broken or

obstructed by other objects blocking the

view of the sensor.

With the automatic control, when it is dark and there is no

vehicle ahead, the system will turn on the high beams; when

it is quite bright in the front surroundings or the system

detects the headlamps or tail lamps ahead, the system will

turn off the high beams.

The headlamps of other vehicles are

obstructed or blocked and cannot be

detected.

When pedestrians, non-motor vehicles

and other objects with no obvious light

or reﬂected light are encountered.

When the headlamps and tail lamps of

other vehicles cannot be detected due

to the sensor view being impaired due

to undulating road conditions such as

bends, dips or hills.

To enable the smart high beam system, the following

conditions should be met:

1

2

3

The light lever switch is placed in position 'AUTO' and

the low beams will automatically turn on.

The vehicle is running with the speed exceeding 25mph

(40km/h).

The front fog lamps^*are not illuminated.

•

When the car is driving on a winding road

or mountainous road.

The smart high beam system automatically exits when the

following conditions are met: After the system has been

exited for 2 seconds, quick pushing the high beam ON

The wiper switch is in the 'Fast Wipe'

position.

74

BRIEF INTRODUCTION TO VEHICLE FUNCTIONS

IMPORTANT

switch twice towards the instrument panel will enter the

smart high beam system again. Within 2 seconds after

the system exits, quick pushing the high beam ON switch

once towards the instrument panel will enter the smart

high beam system again. The smart high beam system

automatically exits when the following conditions are

met. When the smart high beam system is enabled and

low beams automatically turn on, manually switch to high

beams. It can only be exited for not more than three times

in a start cycle otherwise this feature cannot be enabled

again in the current start cycle:

The Automatic High Beam function uses data from the

front view camera, always keep the windscreen clean

and free from residue in this area to maintain optimum

performance of this system. Any damage in this area

such as stone chips must be repaired at the earliest

convenience.

2

Turn Signal Lamp

•

When the smart high beam system is enabled and high

beams automatically turn on, manually switch to low

beams.

•

When the smart high beam system is enabled and high

beams automatically turn on, toggle the high beam

ﬂashing switch.

75

BRIEF INTRODUCTION TO VEHICLE FUNCTIONS

With the Start switch in the ON/RUNNING/READY

the indicator on the instrument panel will illuminate. The

rear fog lamp function can be set in the Vehicle Settings

interface on the entertainment display.

position, push the light lever switch upward or downward

to turn on the turn signal lamp. The corresponding

GREEN indicator lamp in the instrument pack will ﬂash

when the turn signal lamps are working.

Front Fog Lamps^*

After resetting the steering wheel, the lever will be

automatically reset to the centre and the turn signal lamps

go off. If the steering wheel angle is small, manually reset

the lever to turn off the turn signal lamps.

With the Start switch in the ON/RUNNING/READY

position and the side lamps on, turn on the front fog

lamp switch to turn on the front fog lamps. The indicator

illuminates on the instrument panel when the front fog

lamps are on. The front fog lamp function can be set in the

Vehicle Settings interface on the entertainment display.

If the light lever switch is moved at a small angle, it will reset

immediately. The turn signal lamps and direction indicator

lamps will ﬂash three times and then go out automatically.

Hazard Warning Lamp

Rear Fog Lamps

Press the hazard warning lamp switch in the centre of the

A/C control panel to

turn on the hazard warning lamps.

In severe conditions (during foggy weather

for instance), weather lights can provide

additional lights and improve the visibility

range. Using them in clear conditions may

dazzle pedestrians or other road users.

All turn signal lamps and direction indicator lamps will ﬂash

together. Press the button again to switch off the hazard

warning lamp. All turn signal lamps and direction indicator

lamps will stop ﬂashing.

With the Start switch in the ON/RUNNING/READY

position and the low beams on, open rear fog lamp switch

to turn on the rear fog lamps. With rear fog lamps on,

76

Lights and Switches for Your Mg HS SUV Second Generation (2024-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals