Get Emergency Information Guide for Mg Zs SUV First Generation (2017-2024)

Emergency Information

226 Hazard Warning Devices

228 Emergency Starting

230 Vehicle Recovery

235 Tyre Repair and Wheel

Replacement

242 Fuse Replacement

250 Bulb Replacement

5

EMERGENCY INFORMATION

Hazard Warning Devices

Hazard Warning Lights

is in a hazardous situation. Remember to switch off

before driving away.

Warning Triangle

Note: Before you stop or slow the car in an emergency,

always press the hazard warning switch. All the

direction indicators will ﬂash together to warn other

road users when your car is causing an obstruction or

The warning triangle supplied with your car is stowed in

the loadspace.

If you have to stop your car on the road in an emergency,

you must place a warning triangle approximately 50 - 150

226

EMERGENCY INFORMATION

metres behind the car, if possible, to warn other road users

of your position.

5

227

EMERGENCY INFORMATION

Emergency Starting

Using Booster Cables

Starting the Car

Ensure that each booster cable connection is

securely made. There must be no risk of the

clips accidentally slipping from the battery

terminals (as a result of engine vibration, for

example), this could cause sparking, which

could lead to ﬁre or explosion.

NEVER attempt to start the engine by

pushing or towing.

Make sure that both batteries are of the same

rated voltage (12 volts), and that the booster

cables are approved for use with 12 volt car

batteries.

Ensure sparks and naked ﬂames are kept well

away from the front compartment.

Using booster cables (jump leads) from a donor battery,

or a battery ﬁtted to a donor vehicle, is the only approved

method of powering a car with a ﬂat battery.

If the battery from a donor vehicle is to be used, make sure

that the vehicles are parked so that the two batteries are

adjacent to one another and that both the vehicles do not

touch.

228

EMERGENCY INFORMATION

Ensure the START/STOP switch is turned off and switch off

ALL electrical equipment of BOTH vehicles, then follow the

instructions below:

shutting down the engine of the donor vehicle and

disconnecting the booster cables.

Important

1

Connect the RED booster cable between the positive

(+) terminals of both batteries. Connect the BLACK

booster cable from the negative (-) terminal of the

donor battery (A) to a good earth point (an engine

mounting or other unpainted surface, for example), as

far away from the battery as possible and well away

from fuel and brake lines on the disabled vehicle (B).

NEVER turn on any electrical equipment on the

started vehicle before removing the booster cables.

5

Disconnecting the booster cables must be an exact

reversal of the procedure used to connect them, i.e.

disconnect the BLACK cable from the earth point on

the disabled vehicle FIRST.

2

3

Check that the cables are clear of moving parts of both

engines, then start the engine of the donor vehicle and

allow it to idle for a few minutes.

5

Now start the engine of the vehicle with the

discharged battery (DO NOT crank the engine for

more than 10 seconds). If the disabled vehicle will

not start after several attempts, it may need to be

repaired. Please contact the MG Authorised Repairer.

4

After both the vehicles have normally started, allow

the engines to idle for more than 2 minutes before

229

EMERGENCY INFORMATION

Vehicle Recovery

Towing for Recovery

Towing Eye

DO NOT use a tow rope that is twisted - any untwisting force could unscrew the towing eye.

230

EMERGENCY INFORMATION

Your car is equipped with a removable towing hook, that

can be used at the front or the rear of your vehicle. The

towing hook is stored in the tool kit beneath the loadspace

ﬂoor when not in use.

Towing for Recovery

If, due to an electrical fault, potential safety

hazards may exist, it is not allowed to put the

START/STOP Switch in the ON/RUNNING

position.

To ﬁt the towing hook, ﬁrst press one end of the small

cover plate (the white dot in the ﬁgure above), then open

the small cover plate after the other end is lifted, then

screw the towing hook through the small hole into the

threaded hole on the bumper beam (as shown in the

ﬁgure). Ensure the towing eye is fully tightened.

When towing, DO NOT suddenly accelerate

or brake suddenly, this can cause accidents.

The towing speed of a vehicle must not

exceed 20 mph (30 km/h), the towing

distance shall not exceed 30 miles (50 km).

Note: The towing eye cover may be secured to the

bumper by a plastic cord.

5

Suspended Towing

Both towing points are intended for use by qualiﬁed

recovery specialists to assist in the recovery of your car

when a breakdown or accident occur, such as pulling your

vehicle onto the trailer, etc. They are not designed for

towing other vehicles, and must NEVER be used to tow a

trailer or caravan. The car can be towed by using a soft

rope, but a hard rod is preferred.

If your car needs to be towed, most qualiﬁed recovery

specialists will use wheel lift equipment to suspend the

front wheels, while the rear wheels remain on the ground.

Ensure the parking brake is released, the hazard warning

lamps are activated and no passengers are left in the vehicle.

231

EMERGENCY INFORMATION

1

2

Switch

the

START/STOP

Switch

to

the

ON/RUNNING position to enable the brake lights,

wipers and direction indicators to be operated if

necessary. If, due to an electrical fault, it is considered

unsafe to switch the START/STOP Switch on, the car

will need to be recovered on a trailer.

Place the shift lever in

N

position (manual

transmission), or in

transmission).

N

position (automatic

3

4

5

Release the parking brake.

Turn on the hazard warning lamps.

If the transmission is damaged or has a lack of

lubricating oil, DO NOT tow the vehicle with four

wheels on the ground.

6

DO NOT tow backward with front wheels (drive

wheels) on the ground.

Four-Wheel Touchdown Towing

If vehicle is towed with the four wheels on the ground,

observe the following precautions:

232

EMERGENCY INFORMATION

Transporter or Trailer with Rope

If your car is to be transported on the back of a trailer or

transporter, it must be secured as illustrated:

Without the engine running, greater effort will be required

to operate the brake pedal and turn the steering wheel.

Longer stopping distances will also be experienced.

5

1

Position the car on the trailer, apply the parking

brake, and place the shift lever in position

N

(manual transmission), or in P position (automatic

transmission).

233

EMERGENCY INFORMATION

2

Place the wheel chock (1) as shown in the ﬁgure,

then place the anti slip rubber pad (2) around the

circumference of the tyre.

3

Fit the lashing straps (3) around the wheels and secure

to the trailer. Tighten the straps until the car is

securely held.

234

EMERGENCY INFORMATION

Tyre Repair and Wheel Replacement

Tool Identiﬁcation

Tyre Repair

1

Remove the label at the bottom of the repair ﬂuid

reservoir and attach it to the steering wheel to remind

the driver not to exceed 50 mph (80 km/h).

5

1

2

3

4

Towing Hook

2

Connect the air hose of the electric air pump to

the repair ﬂuid reservoir, ﬁt the tyre sealant bottle

(upright) into the slot on the compressor. Remove

the valve dust cap of the ﬂat tyre, and connect the

ﬁller hose from the tyre sealant bottle to the tyre

Electric Air Pump

Wheel Bolt Cap Removal Tool

Repair Fluid Reservoir

235

EMERGENCY INFORMATION

valve. Ensure that the power switch of the electric

air compressor is switched off (i.e., press “O”), then

insert the plug from the compressor into the centre

console power socket, and turn the START/STOP

Switch to the position "ON/RUNNING".

3

Switch on the power switch of the electric compressor

(i.e., press “-”), to start pumping sealant into the

tyre. The tyre sealant bottle will become empty after

approximately 30 seconds. The tyre should reach the

speciﬁed pressure within 5 or 10 minutes.

Note: The pressure gauge may brieﬂy reach 6

bar (87 psi), then the pressure begins to drop to

normal.

4

When the required pressure is reached, switch off the

power switch of the electric compressor (i.e., press

“O”).

Note:

If the required pressure cannot be

reached within 10 minutes, please disconnect the

compressor, drive the vehicle 10 metres (33 feet)

approx forward or backward to allow the sealant

to spread within the tyre. If the required pressure

can still not be reached, the tyre is severely

damaged and you should seek assistance from the

MG Authorised Repairer.

Note:

To avoid battery discharge, it is

recommended to keep the engine running.

236

EMERGENCY INFORMATION

Note: Consecutive operation of Electric air

compressor for more than 10 minutes may result

in damage to the compressor.

•

If the tyre pressure has dropped to less than 0.8 bar

(11.6 psi), do not continue driving, seek assistance

instead.

If the tyre pressure is between 0.8 bar (11.6 psi) and

speciﬁed pressure, connect the hose of electric air

pump to the tyre valve, and connect the plug of the

electric air pump to the power socket, then switch on

the electric air pump to inﬂate the tyre until it reaches

the speciﬁed pressure. Repeat the operations of step 6

after driving a maximum distance of 3 miles (5 km).

Note: Under no circumstances should you

continue your journey with

a

deﬂated tyre.

Driving a vehicle with a deﬂated tyre is extremely

dangerous.

5

6

Remove the tyre sealant bottle from the slot in the

compressor, disconnect the hose from the tyre valve,

remove the compressor plug from the centre console

power socket, return the tyre repair kit to its stowage

tray.

5

After successfully adding sealant to the tyre, drive

immediately for a short time (around one minute) this

will allow the sealant to distribute evenly inside the

tyre. Continue driving and do not exceed 50 mph(80

km/h).After a further 10 minutes, ﬁnd a safe place to

stop and recheck the tyre pressure.

Please take different measures based on the tyre pressure

measured:

237

EMERGENCY INFORMATION

*

•

If the tyre pressure has not dropped, you may continue

driving, but the vehicle speed must not exceed 50 MPH

(80 km/h), and the driving mileage must not exceed 125

miles (200 km).

Changing a Wheel

If you need to change the wheel during the journey, choose

a safe place to stop away from the main road if possible.

Always ask your passengers to get out of the car and wait

in a safe area away from other trafﬁc.

Note:

DO NOT remove foreign objects (eg.

screws,nails) from the tyre. The tyre repair system

must only be used when the foreign object is in the

tread pattern (A), DO NOT attempt a repair when

the damage is in the sidewall of the tyre (B).

Switch on hazard warning lamps. If available, position

a warning triangle about 50 to 150 metres behind your

vehicle to warn approaching trafﬁc.

Before changing a wheel, ensure the front wheels are in the

straight ahead position. Apply the parking brake and place

the gear shift lever of transmission in N position.

Observe the following precautions:

•

Ensure the jack is positioned on ﬁrm, level ground.

If the vehicle must be parked on the hill, place chocks

in front of and behind other 3 wheels to prevent the

vehicle moving.

Positioning the Jack

NEVER work beneath the car with the jack

as the only means of support. The jack is

designed for wheel changing only!

238

EMERGENCY INFORMATION

NEVER jack the car using any jacking points

domed head of the jack must ﬁt into the corresponding

recess in the sill plate (There is a triangle indicator in the

area shown by the arrowhead. See the illustration above).

other than the jacking points.

damage to the car could result.

Serious

Turning the jack screw by hand, adjust the jack until the jack

head ﬁts snugly onto the sill in the correct area. Ensure that

the base of the jack is in full contact with the level ground.

Fitting the Spare Wheel

Regularly check the spare wheel tyre

pressure, it may not be used for long

periods of time. After ﬁtment, at the ﬁrst

opportunity check and adjust the tyre

pressure.

5

The wheel bolts must be tightened to the

speciﬁed torque after changing

a

wheel

～

(120 130 Nm).

Avoid accidental contact with any underbody

parts, especially hot exhaust system

components.

1

Before raising the car, use the special tool supplied

with the vehicle to remove each wheel bolt cap. Use

the wheel bolt spanner to slacken each bolt half a turn

anti-clockwise.

Position the jack on ﬁrm level ground under the jacking

point nearest the wheel to be removed. Note that the

239

EMERGENCY INFORMATION

2

Turn the handle in a clockwise direction until the tyre

is clear of the ground.

Note: DO NOT stand on the handle of the wheel bolt

spanner or use extension tube on the handle of the

spanner.

3

Remove the wheel bolts and place them in the tool tray

to prevent them from being lost. Make sure the vehicle

is steady and there is no risk of slip or movement

before removing wheel bolts.

Note: When replacing the wheel, please fully tighten

the bolts in the diagonal sequence twice.

Note: Consult your MG Authorised Repairer or tyre

specialist for a replacement tyre, as soon as possible.

4

5

Remove the road wheel.

Note: Avoid placing wheels face down on the

ground - the surface may be scratched.

Spacesaver Spare Wheel

Only one spacesaver spare wheel can be used

at any one time, otherwise the operational

performance and brake performance may be

reduced, thereby leading to accident or injury

to yourself and others.

Fit the spare wheel and tighten the wheel bolts with

wheel bolt spanner until the wheel is seated ﬁrmly

against the hub.

6

7

Lower the car and remove the jack, then FULLY tighten

the wheel bolts in a diagonal sequence.

When driving on icy or slippery surfaces it is

advised to ﬁt the spacesaver wheel to the rear

of the vehicle to maintain adaquate stability.

This may mean swapping a front wheel with

a rear wheel.

Finally, return the tools to the toolbox, put the toolbox

into the well of the boot ﬂoor, tighten the spare wheel

retaining nuts, and put the replaced wheel above the

toolbox in the well in the load space ﬂoor (face down).

Lower the boot ﬂoor, and put the boot storage box on

the boot ﬂoor.

240

EMERGENCY INFORMATION

Snow chains can not be used on the

spacesaver spare wheel, this can cause

damage to the car and snow chain.

When the spacesaver spare wheel is ﬁtted, the vehicle

speed should not exceed 50 mph(80 km/h). Please have

the full-scale tyre repaired and replace the spare wheel as

soon as possible. This will extend the life span of the spare

wheel for other emergencies.

Note: DO NOT use an automatic car wash when

the spacesaver wheel is ﬁtted, the guide rails of the

car wash may conﬂict with the wheel/tyre and cause

damage.

5

241

EMERGENCY INFORMATION

Fuse Replacement

Fuse Box

There are two fuse boxes in the vehicle：

Fuse

Fuses are simple circuit breakers which protect the vehicle

electrical equipment by preventing the electrical circuits

from being overloaded. A blown fuse indicates that the

item of electrical equipment it protects stops working.

Check a suspect fuse by removing it from the fuse box and

looking for a break in the wire inside the fuse.

It is recommended to have spare fuses in the vehicle, which

can be obtained from a local MG Authorised Repairer.

IMPORTANT

•

NEVER attempt to repair a blown fuse. ALWAYS

replace a fuse with one of the same rating.

If a replaced fuse fails immediately, please contact an

MG Authorised Repairer as soon as possible.

1

2

Front Compartment Fuse Box（at the left side of the

Front Bay）.

Passenger Compartment Fuse Box（below the glove

box at the front passenger side）.

242

EMERGENCY INFORMATION

Passenger Compartment Fuse Box

3

4

Press the fuse extraction tool onto the fuse head

and pull to remove the fuse. A blown fuse can be

recognised by a break in the wire.

Replace the blown fuse with a same rating.

Fuse Speciﬁcation

NO.

Specs

Function

Front Washer Relay, Rear

Washer Relay

F1

15A

F2

F3

F4

F5

10A

5A

Diagnostic Socket

5

PRND Display

10A

Front Left Seat Heating Relay

Airbag ECU (SDM)

Check or Replace a Fuse

1

Switch off the vehicle power system and all electrical

equipment, disconnect the battery negative cable.

Keyless Start/Stop Switch,

Gateway

F6

10A

2

Remove the closing panel below the glove box to gain

access to the fuse box.

F7

F8

30A

15A

Driver Seat Adjust Switch

Super Lock Relay

243

EMERGENCY INFORMATION

NO.

Specs

Function

NO.

F21

Specs

10A

Function

－

F9–F11

360° View Module, Passenger

Compartment Fuse F12

Left Rear Driving Assistance

Radar

F12

5A

Exterior Mirrors Heating

Element

F22

F23

F24

10A

25A

20A

－

F13–F14

F15

Rear Windscreen Heating

Element

15A

Front Power Socket

Front Courtesy Lamp, Outside

Mirror and Master Light Height

Adjust Switch, Top USB, Left

Headlamp Assembly, Right

Headlamp Assembly

Front Central Display, Front

Infotainment Control Module

F16

5A

Electronic Temperature

Controller

F25

F26

F27

10A

5A

F17

F18

5A

Rear USB

Instrument Pack

EPB Switch

Transmission Control

Module-AT

10A

Outside Mirror and Master

Light Height Adjust Switch, Rain

Light Sensor

F19

F20

5A

F28

F29

F30

5A

30A

5A

Information Faceplate

Sunroof

10A

Front Right Seat Heating Relay

DAB Module

244

EMERGENCY INFORMATION

NO.

F31

Specs

5A

Function

Tyre Pressure Monitoring

System

Electronic Steering Column

Lock

F32

10A

F33

30A

Sunroof

－

F34–F41

Stability Control

Module(Valve)-MT

F42

F43

25A

40A

30A

5

Stability Control

Module(Valve)-AT

Passenger Window lift Switch,

Rear Left Window Lift Switch

Driver Door Switch Pack,

Driver Window Lifter, Rear

Right Window Lift Switch

F44

30A

245

EMERGENCY INFORMATION

Front Compartment Fuse Box

Check or Replace a Fuse

1

Switch off the vehicle power system and all electrical

equipment, disconnect the battery negative cable.

2

3

Press the locating clips to remove the fuse box lid.

Press the fuse extraction tool onto the fuse head

and pull to remove the fuse. A blown fuse can be

recognized by a break in the wire.

4

Replace the fuse with a same rating.

Fuse Speciﬁcation

NO.

FL1

FL2

FL3

Specs

150A

80A

Function

Alternator

Electric Power Steering Module

Cooling Fan Relay Pack

40A

Windscreen/Mirror Heating Relay,

Passenger Compartment Fuse F18,

F19, F20, F21, F42, F43, F44

FL4

80A

246

EMERGENCY INFORMATION

NO.

FL5

Specs

80A

Function

NO.

FL15

FL16

FL17

F1

Specs

－

Function

－

KLR Relay, Passenger

Compartment Fuse F1, F2,

F3, F4, F5, F6, F7, F8, F24, F25,

F26, F27, F28, F29, F30, F31, F32,

F33

30A

－

DC/DC Convertor

－

10A

Right Headlamp Assembly

－

FL6

FL7

Downstream Lambda Sensor,

Upstream Lambda Sensor, Positive

Temperature Coefﬁcient(1.5L),

Intake Variable Camshaft

Timing(1.0T), Exhaust Variable

Camshaft Timing(1.0T), Oil

Control Valve(1.0T), Canister

Purge Valve(1.0T)

Electronic Temperature

Controller, Blower

40A

FL8

FL9

20A

40A

－

Body Control Module

F2

15A

5

Stability Control Module(Pump)

－

FL10

FL11

FL12

FL13

FL14

－

F3

F4

F5

F6

10A

5A

Left Headlamp Assembly

Compressor Relay

－

30A

－

Starter Relay

Engine Control Module

Fuel Injector(1.5L)

－

10A

247

EMERGENCY INFORMATION

NO.

F7

Specs

30A

Function

NO.

F15

Specs

10A

Function

Front Wiper Enable Relay, Front

Wiper High/Low Speed Relay

Intake Variable Camshaft

Timing(1.5L), Exhaust Variable

Camshaft Timing(1.5L), Canister

Purge Valve(1.5L), Electronic

Thermostat(1.0T), Electronic

Water Pump(1.0T), Dump

Valve(1.0T), Waste Gate Control

Valve(1.0T), Clutch Master

Cylinder Sensor(1.0T)

Cooling Fan Relay Pack, Brake

Pedal Switch, Fuel Pump Relay,

AC Pressure Switch, Neutral

Switch(1.5L)

F8

5A

F9

20A

10A

Fuel Pump Relay

F10

F11

Right Headlamp Assembly

Left Headlamp Assembly

F16

F17

F18

15A

10A

5A

Rear Wiper Relay

Fog Lamp Relay

Ignition Coil, Engine Control

Module

F12

30A

Airbag ECU (SDM)

Instrument Pack, Front Detect

Radar, Front View Control Module,

Shifter Mechanism, Reverse Lamp

Switch, DC/DC Convertor, Airbag

Display Module

F13

F14

15A

Horn Relay

－

F19

F20

5A

Engine Control Module

248

EMERGENCY INFORMATION

NO.

F21

F22

F23

F24

F25

F26

F27

F28

F29

F30

Specs

Function

25A

Body Control Module

－

-

30A

-

Body Control Module

－

15A

-

Body Control Module

5

－

-

5A

Engine Control Module

249

EMERGENCY INFORMATION

Bulb Replacement

Bulb Speciﬁcation

Lamp Bulb

Speciﬁcations

Lamp Bulb

Rear Side Light

Speciﬁcations

Headlamp High/Low

Beam

LED

Stop Lamps

Front Direction

Indicators

License Plate Lamps

Rear Fog Lamps

W5W 5W

LED

Daytime Running Lamps LED

Front Side Light

Front Fog Lamps ^*

Reverse Lamps

LED

High Mounted Stop Lamp LED

H8 35W

Interior Lamp

W5W 5W

C10W 10W

W16W 16W

Load Space Lamp

Rear Direction Indicators WY16W 16W

250

EMERGENCY INFORMATION

Bulb Replacement

Front Fog Lamps Bulb Renewal

1

Disconnect the battery negative terminal.

Before replacing any bulb, turn off the lighting switch to

avoid any possibility of a short circuit.

2

For front fog lamps bulb replacement, it is necessary

to remove the front bumper cover, seek guidance from

an Authorised MG Repairer.

Note: MG only recommends replacement bulbs that

completely meet the manufacturers speciﬁcations.

3

4

Remove the wiring connector from the bulb.

Rotate the bulb anti-clockwise and remove.

Take care NOT to touch the glass with your ﬁngers; always

use a cloth to handle the bulb. If necessary, clean the glass

with methylated spirits to remove ﬁngerprints.

If in doubt, when replacing bulbs, contact an MG

Authorised Repairer.

5

For replacement of other bulbs not listed please consult an

MG Authorised Repairer.

251

EMERGENCY INFORMATION

5

Locate the bulb in the lamp, rotate clockwise until fully

secured.

Reverse Lamps Bulb Renewal

1

2

3

Open the tailgate.

6

7

8

9

Reﬁt the wiring connector to the new bulb.

Fit the front bumper cover.

Disconnect the battery negative terminal.

Using a suitable pry bar or lever, carefully remove the

cover trim.

Connect the negative battery terminal.

Test lamp operation.

4

Using a suitable spanner/socket wrench, remove the 3

screws (1) securing the lamp to the tailgate. Remove

the wiring connector (2). Release the lamp assembly

and remove away from the body.

252

EMERGENCY INFORMATION

5

Rotate the bulb holder in an anti-clockwise direction.

6

7

8

Remove bulb holder and remove bulb.

Fit new bulb to bulb holder.

Insert bulb holder in lamp assembly, rotate clockwise

until fully secure.

9

Ensure lamp seal is correctly located.

10 Position lamp to tailgate, reﬁt the wiring connector

and the screw ﬁxings, and tighten to 2.7-3.3 Nm.

253

EMERGENCY INFORMATION

11 Reﬁt screw cover trim.

12 Reconnect battery negative terminal.

13 Test lamp operation.

License Plate Lamps Bulb Renewal

1

Disconnect the battery negative terminal.

2

For license plate lamps bulb replacement, it is

necessary to remove the rear bumper cover, seek

guidance from an Authorised MG Repairer.

14 Close tailgate.

3

4

Remove the wiring connector.

Rotate the bulb holder in an anti-clockwise direction.

254

EMERGENCY INFORMATION

5

6

7

Remove bulb holder and remove bulb.

Fit new bulb to bulb holder.

Rear Direction Indicator Bulb Renewal

1

2

3

Open the tailgate.

Disconnect the battery negative terminal.

Insert bulb holder in lamp assembly, rotate clockwise

until fully secure.

Using a suitable pry bar or lever, carefully release and

remove the securing screw cover trim.

8

9

Reﬁt the wiring connector.

Fit the rear bumper cover.

4

Using a suitable spanner/socket wrench, remove the 2

screws securing the lamp to the body.

10 Reconnect battery negative terminal.

11 Test lamp operation.

5

255

EMERGENCY INFORMATION

5

Remove the wiring connector. Release the lamp

assembly and remove away from the body.

10 Ensure lamp seal is correctly located.

11 Position lamp to body, reﬁt the wiring connector, start

both screw ﬁxings, and tighten to 3-5 Nm.

6

Rotate the bulb holder in an anti-clockwise direction.

12 Reﬁt screw cover trim.

13 Reconnect battery negative terminal.

14 Test lamp operation.

15 Close tailgate.

7

8

9

Remove bulb holder and remove bulb.

Fit new bulb to bulb holder.

Insert bulb holder in lamp assembly, rotate clockwise

until fully secure.

256

EMERGENCY INFORMATION

Interior Lamp Bulb Renewal

assembly. Push the lens upwards until it ‘clicks’ into

position

1

Disconnect the battery negative terminal.

6

7

Connect battery negative terminal.

Test lamp operation.

2

Use a suitable tool or small ﬂat bladed screwdriver to

gently prise front end of the lens, and remove the lens.

5

3

4

5

Pull the bulb from its mounting to remove.

Install new bulb.

Install the lens, locate the two prongs at the front

of the lens and then carefully ﬂex the lens to locate

the two prongs at the rear of the lens into the lamp

257

EMERGENCY INFORMATION

Load Space Lamp Bulb Renewal

1

2

3

Open the tailgate.

Disconnect the battery negative terminal.

Insert a suitable tool or small ﬂat bladed screwdriver

into the indent on one of the narrow sides of the lens

and carefully remove the unit from its location.

4

5

6

7

8

9

Pull the bulb from its mounting to remove.

Install new bulb.

Reﬁt the unit, push until fully secured.

Connect battery negative terminal.

Test lamp operation.

Close tailgate.

258

Emergency Information for Your Mg Zs SUV First Generation (2017-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals