2017-2024 Mg Zs SUV Emergency Information -> Bulb Replacement User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Emergency Information -> Bulb Replacement for Your Mg Zs SUV First Generation (2017-2024)

EMERGENCY INFORMATION  
Bulb Replacement  
Bulb Specification  
Lamp Bulb  
Specifications  
Lamp Bulb  
Rear Side Light  
Specifications  
Headlamp High/Low  
Beam  
LED  
LED  
LED  
LED  
Stop Lamps  
Front Direction  
Indicators  
License Plate Lamps  
Rear Fog Lamps  
W5W 5W  
LED  
Daytime Running Lamps LED  
Front Side Light  
Front Fog Lamps *  
Reverse Lamps  
LED  
High Mounted Stop Lamp LED  
H8 35W  
Interior Lamp  
W5W 5W  
C10W 10W  
W16W 16W  
Load Space Lamp  
Rear Direction Indicators WY16W 16W  
250  
EMERGENCY INFORMATION  
Bulb Replacement  
Front Fog Lamps Bulb Renewal  
1
Disconnect the battery negative terminal.  
Before replacing any bulb, turn off the lighting switch to  
avoid any possibility of a short circuit.  
2
For front fog lamps bulb replacement, it is necessary  
to remove the front bumper cover, seek guidance from  
an Authorised MG Repairer.  
Note: MG only recommends replacement bulbs that  
completely meet the manufacturers specifications.  
3
4
Remove the wiring connector from the bulb.  
Rotate the bulb anti-clockwise and remove.  
Take care NOT to touch the glass with your fingers; always  
use a cloth to handle the bulb. If necessary, clean the glass  
with methylated spirits to remove fingerprints.  
If in doubt, when replacing bulbs, contact an MG  
Authorised Repairer.  
5
For replacement of other bulbs not listed please consult an  
MG Authorised Repairer.  
251  
EMERGENCY INFORMATION  
5
Locate the bulb in the lamp, rotate clockwise until fully  
secured.  
Reverse Lamps Bulb Renewal  
1
2
3
Open the tailgate.  
6
7
8
9
Refit the wiring connector to the new bulb.  
Fit the front bumper cover.  
Disconnect the battery negative terminal.  
Using a suitable pry bar or lever, carefully remove the  
cover trim.  
Connect the negative battery terminal.  
Test lamp operation.  
4
Using a suitable spanner/socket wrench, remove the 3  
screws (1) securing the lamp to the tailgate. Remove  
the wiring connector (2). Release the lamp assembly  
and remove away from the body.  
252  
EMERGENCY INFORMATION  
5
5
Rotate the bulb holder in an anti-clockwise direction.  
6
7
8
Remove bulb holder and remove bulb.  
Fit new bulb to bulb holder.  
Insert bulb holder in lamp assembly, rotate clockwise  
until fully secure.  
9
Ensure lamp seal is correctly located.  
10 Position lamp to tailgate, refit the wiring connector  
and the screw fixings, and tighten to 2.7-3.3 Nm.  
253  
EMERGENCY INFORMATION  
11 Refit screw cover trim.  
12 Reconnect battery negative terminal.  
13 Test lamp operation.  
License Plate Lamps Bulb Renewal  
1
Disconnect the battery negative terminal.  
2
For license plate lamps bulb replacement, it is  
necessary to remove the rear bumper cover, seek  
guidance from an Authorised MG Repairer.  
14 Close tailgate.  
3
4
Remove the wiring connector.  
Rotate the bulb holder in an anti-clockwise direction.  
254  
EMERGENCY INFORMATION  
5
6
7
Remove bulb holder and remove bulb.  
Fit new bulb to bulb holder.  
Rear Direction Indicator Bulb Renewal  
1
2
3
Open the tailgate.  
Disconnect the battery negative terminal.  
Insert bulb holder in lamp assembly, rotate clockwise  
until fully secure.  
Using a suitable pry bar or lever, carefully release and  
remove the securing screw cover trim.  
8
9
Refit the wiring connector.  
Fit the rear bumper cover.  
4
Using a suitable spanner/socket wrench, remove the 2  
screws securing the lamp to the body.  
10 Reconnect battery negative terminal.  
11 Test lamp operation.  
5
255  
EMERGENCY INFORMATION  
5
Remove the wiring connector. Release the lamp  
assembly and remove away from the body.  
10 Ensure lamp seal is correctly located.  
11 Position lamp to body, refit the wiring connector, start  
both screw fixings, and tighten to 3-5 Nm.  
6
Rotate the bulb holder in an anti-clockwise direction.  
12 Refit screw cover trim.  
13 Reconnect battery negative terminal.  
14 Test lamp operation.  
15 Close tailgate.  
7
8
9
Remove bulb holder and remove bulb.  
Fit new bulb to bulb holder.  
Insert bulb holder in lamp assembly, rotate clockwise  
until fully secure.  
256  
EMERGENCY INFORMATION  
Interior Lamp Bulb Renewal  
assembly. Push the lens upwards until it ‘clicks’ into  
position  
1
Disconnect the battery negative terminal.  
6
7
Connect battery negative terminal.  
Test lamp operation.  
2
Use a suitable tool or small flat bladed screwdriver to  
gently prise front end of the lens, and remove the lens.  
5
3
4
5
Pull the bulb from its mounting to remove.  
Install new bulb.  
Install the lens, locate the two prongs at the front  
of the lens and then carefully flex the lens to locate  
the two prongs at the rear of the lens into the lamp  
257  
EMERGENCY INFORMATION  
Load Space Lamp Bulb Renewal  
1
2
3
Open the tailgate.  
Disconnect the battery negative terminal.  
Insert a suitable tool or small flat bladed screwdriver  
into the indent on one of the narrow sides of the lens  
and carefully remove the unit from its location.  
4
5
6
7
8
9
Pull the bulb from its mounting to remove.  
Install new bulb.  
Refit the unit, push until fully secured.  
Connect battery negative terminal.  
Test lamp operation.  
Close tailgate.  
258  

Related Topics

Emergency Information
Emergency Starting Vehicle Recovery Tyre Repair and Wheel Replacement Fuse Replacement

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot