Get Safety ? seats, seat belts and supplemental restraint system -> Child restraints Guide for Nissan Juke SUV First Generation (2010-2019)

CHILD RESTRAINTS

serious injury or death in an accident.

SEAT BELT MAINTENANCE

PRECAUTIONS ON CHILD RESTRAINT

USAGE

.

Follow all of the child restraint manufac-

turer’s instructions for installation and use.

When purchasing a child restraint, be sure to

select one which will fit your child and

vehicle. It may not be possible to properly

install some types of child restraint in your

vehicle.

Periodically check that the seat belt and all the metal

components, such as buckles, tongues, retractors,

flexible wires and anchors, work properly. If loose parts,

deterioration, cuts or other damage on the seat belt

webbing is found, the entire seat belt assembly should

be replaced.

If dirt builds up in the shoulder belt guide of the seat

belt anchors, the seat belts may retract slowly. Wipe

the shoulder belt guide with a clean, dry cloth.

The direction of the child restraint, either

front-facing or rear-facing, depends on the

type of the child restraint and the size of the

child. Refer to the child restraint manufac-

turer’s instructions for details.

To clean the seat belt webbing, apply a mild soap

solution or any solution recommended for cleaning

upholstery or carpet. Then wipe with a cloth and allow

the seat belts to dry in the shade. Do not allow the seat

belts to retract until they are completely dry.

SSS0099

.

Adjustable seatbacks should be positioned

to fit the child restraint, but as upright as

possible.

WARNING:

After attaching

a

child restraint, test it

.

Infants and small children should always be

placed in an appropriate child restraint while

riding in the vehicle. Failure to use a child

restraint can result in serious injury or death.

before you place the child in it. Push it from

side to side and tug it forward to make sure

that it is held securely in place. The child

restraint should not move more than 25 mm

(1 in). If the restraint is not secure, tighten

the belt as necessary, or install the restraint

in another seat and test it again.

Infants and small children should never be

carried on your lap. It is not possible for even

the strongest adult to resist the forces of a

severe accident. The child could be crushed

between the adult and parts of the vehicle.

Also, do not put the same seat belt around

both your child and yourself.

.

When the child restraint is not in use, keep it

secured with the ISOFIX child restraint

system or a seat belt to prevent it from

being thrown around in case of a sudden

stop or accident.

.

NISSAN recommends that the child re-

straints be installed in the rear seat. Accord-

ing to accident statistics, children are safer

when properly restrained in the rear seat

than in the front seat.

Never install a rear-facing child restraint on

the front passenger’s seat when the front

passenger’s air bag is available. Supple-

mental front-impact air bags inflate with

Improper use or improper installation of a

child restraint can increase the risk or

severity of injury for both the child and other

occupants of the vehicle and can lead to

great force.

A

rear-facing child restraint

could be struck by the supplemental front-

impact air bags in an accident and could

1-12 Safety — seats, seat belts and supplemental restraint system

seriously injure or kill your child.

seat belt to secure the child restraint. Check your child

restraint for a label stating that it is compatible with the

ISOFIX child restraints. This information may also be in

the instructions provided by the child restraint manu-

facturer.

ISOFIX lower anchor point locations

.

If the seat belt in the position where a child

restraint is installed requires

device and if it is not used, injuries could

result from a child restraint tipping over

during normal vehicle braking or cornering.

The ISOFIX anchor points are provided to install child

restraints in the rear outboard seating positions only.

Do not attempt to install a child restraint in the

center position using the ISOFIX anchors.

a

locking

ISOFIX child restraints generally require the use of a

top tether strap or other anti-rotation devices such as

support legs. When installing ISOFIX child restraints,

carefully read and follow the instructions in this manual

and those supplied with the child restraints. (See

“Child restraint installation using ISOFIX (for rear

seat)” (P.1-14).)

CAUTION:

Remember that a child restraint left in a closed

vehicle can become very hot. Check the seating

surface and buckles before placing your child in

a child restraint.

CHILD RESTRAINT ANCHORAGE (if

equipped)

Your vehicle is designed to accommodate a child

restraint system on the rear seat. When installing a

child restraint system, carefully read and follow the

instructions in this manual and those supplied with the

child restraint system.

NISSAN recommends that infants and small children

be seated in a child restraint. You should choose a

child restraint that fits your vehicle and always follow

the manufacturer’s instructions for installation and use.

In addition, there are many types of child restraints

available for larger children that should be used for

maximum protection.

SSS0637

ISOFIX lower anchor location

The ISOFIX anchors are located at the rear of the seat

cushion near the seatback. A label is attached to the

seatback to help you locate the ISOFIX anchors.

WARNING:

ISOFIX CHILD RESTRAINT SYSTEM (if

equipped)

ISOFIX child restraint anchor attachments

.

Child restraint anchorages are designed to

withstand only those loads imposed by

correctly fitted child restraints. Under no

circumstances are they to be used for adult

seat belts, harnesses or for attaching other

items or equipment to the vehicle. Doing so

could damage the child restraint an-

chorages. The child restraint will not be

properly installed using the damaged an-

chorage, and

a

child could be seriously

injured or killed in a collision.

SSS0644

.

The child restraint top tether strap may be

damaged by contact with the cargo cover (if

equipped) or items in the luggage area.

Remove the cargo cover from the vehicle or

SSS1046

Anchor attachment

ISOFIX label location

ISOFIX child restraints include two rigid attachments

that can be connected to two anchors located in the

seat. With this system, you do not have to use a vehicle

Your vehicle is equipped with special anchor points

that are used with ISOFIX child restraint systems.

Safety — seats, seat belts and supplemental restraint system 1-13

secure it and any luggage. Your child could

be seriously injured or killed in a collision if

the top tether strap is damaged.

.

Inspect the lower anchors by inserting your

fingers into the lower anchor area and

feeling to make sure there are no obstruc-

tions over the ISOFIX anchors, such as seat

belt webbing or seat cushion material. The

child restraint will not be secured properly if

the ISOFIX anchors are obstructed.

Installation on rear outboard seats

Front-facing:

Anchorage location

Child restraint anchorages are designed to

withstand only those loads imposed by

correctly fitted child restraints. Under no

circumstances are they to be used for adult

seat belts, harnesses or for attaching other

items or equipment to the vehicle. Doing so

could damage the child restraint an-

chorages. The child restraint will not be

properly installed using the damaged an-

SSS0646A

Steps 1 and 2

Be sure to follow the manufacturer’s instructions for

the proper use of your child restraint. Follow these

steps to install a front-facing child restraint on the rear

outboard seats using ISOFIX:

JVR0266X

chorage, and

a

child could be seriously

injured or killed in a collision.

The anchor points are located on the back side of the

seatbacks.

1

1. Position the child restraint on the seat

.

*

CHILD RESTRAINT INSTALLATION USING

ISOFIX (for rear seat)

2. Secure the child restraint anchor attachments to

2

the ISOFIX lower anchors

.

*

WARNING:

3. The back of the child restraint should be secured

against the vehicle seat back. If necessary, adjust

or remove the head restraint to obtain the correct

child restraint fit. (See “Head restraints” (P.1-5).) If

the head restraint is removed, store it in a secure

place. Be sure to install the head restraint when

the child restraint is removed. If the seating

position does not have an adjustable head

restraint and it is interfering with the proper child

.

Attach ISOFIX child restraints only at the

specified locations. For the ISOFIX lower

anchor locations, see “ISOFIX child restraint

system” (P.1-13). If a child restraint is not

secured properly, your child could be ser-

iously injured or killed in an accident.

.

Do not install child restraints that require the

use of a top tether strap to seating positions

that do not have a top tether anchor.

restraint fit, try another seating position or

different child restraint.

a

Do not secure a child restraint in the center

rear seating position using the ISOFIX lower

anchors. The child restraint will not be

secured properly.

1-14 Safety — seats, seat belts and supplemental restraint system

1

1. Position the child restraint on the seat

.

*

2. Secure the child restraint anchor attachments to

2

*

the ISOFIX lower anchors

.

SSS0754A

SSS0755A

Step 4

Step 7

4. Shorten the rigid attachment to have the child

7. Test the child restraint before you place the child

3

restraint firmly tightened; press downward

*

5

in it

. Push the child restraint from side to side

*

SSS0756A

4

*

and rearward

firmly in the center of the child

and tug it forward to make sure that it is held

securely in place.

Step 3

restraint with your knee to compress the vehicle

seat cushion and seatback.

3. Shorten the rigid attachment to have the child

8. Check to make sure that the child restraint is

properly secured prior to each use. If the child

restraint is loose, repeat steps 3 through 7.

3

restraint firmly tightened; press downward

*

5. If the child restraint is equipped with a top tether

strap, route the top tether strap and secure the

tether strap to the tether anchor point. (See “Child

restraint anchorage” (P.1-13).)

4

*

and rearward

firmly in the center of the child

restraint with your hand to compress the vehicle

seat cushion and seatback.

Rear-facing:

4. If the child restraint is equipped with a top tether

strap, route the top tether strap and secure the

tether strap to the tether anchor point. (See “Child

restraint anchorage” (P.1-13).)

6. If the child restraint is equipped with other anti-

rotation devices such as support legs, use them

instead of the top tether strap following the child

restraint manufacturer’s instructions.

5. If the child restraint is equipped with other anti-

rotation devices such as support legs, use them

instead of the top tether strap following the child

restraint manufacturer’s instructions.

SSS0649A

Steps 1 and 2

Be sure to follow the manufacturer’s instructions for

the proper use of your child restraint. Follow these

steps to install a rear-facing child restraint on the rear

outboard seats using ISOFIX:

Safety — seats, seat belts and supplemental restraint system 1-15

2. Route the seat belt tongue through the child

CHILD RESTRAINT INSTALLATION USING

THREE-POINT TYPE SEAT BELT

2

restraint and insert it into the buckle

hear and feel the latch engage.

until you

*

Installation on rear seats - seat belts without

automatic locking mode

3. To prevent slack in the seat belt webbing, it is

necessary to secure the seat belt in place with

locking devices attached to the child restraint.

Front-facing:

SSS0757A

Step 6

6. Test the child restraint before you place the child

5

in it

. Push the child restraint from side to side

*

and tug it forward to make sure that it is held

securely in place.

7. Check to make sure that the child restraint is

properly secured prior to each use. If the child

restraint is loose, repeat steps 3 through 6.

SSS0758A

SSS0647A

Step 1

Step 4

Be sure to follow the manufacturer’s instructions for

the proper use of your child restraint. Follow these

steps to install a front-facing child restraint on the rear

seats using three-point type seat belt without auto-

matic locking mode:

4. Remove any additional slack from the seat belt;

3

4

press downward

and rearward

firmly in

*

the center of the child restraint with your knee to

compress the vehicle seat cushion and seatback

while pulling up on the seat belt.

1

*

1. Position the child restraint on the seat

.

SSS0638A

Step 5

SSS0493A

Step 2

1-16 Safety — seats, seat belts and supplemental restraint system

5. Test the child restraint before you place the child

5

in it

. Push the child restraint from side to side

*

and tug it forward to make sure that it is held

securely in place.

6. Check to make sure that the child restraint is

properly secured prior to each use. If the child

restraint is loose, repeat steps 3 through 5.

Rear-facing:

SSS0654A

SSS0658A

Step 2

Step 5

2. Route the seat belt tongue through the child

5. Test the child restraint before you place the child

2

5

restraint and insert it into the buckle

hear and feel the latch engage.

until you

in it

. Push the child restraint from side to side

*

and tug it forward to make sure that it is held

securely in place.

3. To prevent slack in the seat belt webbing, it is

necessary to secure the seat belt in place with

locking devices attached to the child restraint.

6. Check to make sure that the child restraint is

properly secured prior to each use. If the child

restraint is loose, repeat steps 3 through 5.

SSS0759A

Step 1

Be sure to follow the manufacturer’s instructions for

the proper use of your child restraint. Follow these

steps to install a rear-facing child restraint on the rear

seats using three-point type seat belt without auto-

matic locking mode:

1

*

1. Position the child restraint on the seat

.

SSS0639A

Step 4

4. Remove any additional slack from the seat belt;

3

4

press downward

and rearward

firmly in

*

the center of the child restraint with your hand to

compress the vehicle seat cushion and seatback

while pulling up on the seat belt.

Safety — seats, seat belts and supplemental restraint system 1-17

Installation on rear seats - seat belts with

automatic locking mode

Front-facing:

SSS0493A

SSS0652A

Front-facing: Step 3

Front-facing: Step 5

4

3. Route the seat belt tongue through the child

5. Allow the seat belt to retract

. Pull up on the

*

2

restraint and insert it into the buckle

hear and feel the latch engage.

until you

shoulder belt to remove any slack in the belt.

*

SSS0758A

Front-facing: Step 1

Be sure to follow the manufacturer’s instructions for

the proper use of your child restraint. Follow these

steps to install a front-facing child restraint on the rear

seats using three-point type seat belt with automatic

locking mode:

1

*

1. Position the child restraint on the seat

.

2. The back of the child restraint should be secured

against the vehicle seatback. If necessary, adjust

or remove the head restraint to obtain the correct

child restraint fit. If the seating position does not

have an adjustable head restraint and it is

interfering with the proper child restraint fit, try

SSS0647C

SSS0651A

Front-facing: Step 6

6. Remove any additional slack from the seat belt;

Front-facing: Step 4

5

6

4. Pull the shoulder belt until the belt is fully extended

press downward

and rearward

firmly in

*

another seating position or

restraint.

a

different child

3

*

. At this time, the seat belt retractor is in the

Automatic Locking Retractor (ALR) mode (child

restraint mode).

the center of the child restraint with your knee to

compress the vehicle seat cushion and seatback

while pulling up on the seat belt.

1-18 Safety — seats, seat belts and supplemental restraint system

Rear-facing:

SSS0638B

SSS0655A

Front-facing: Step 7

Rear-facing: Step 3

SSS0759A

7. Test the child restraint before you place the child

3. Pull the shoulder belt until the belt is fully extended

Rear-facing: Step 1

7

3

*

in it

. Push the child restraint from side to side

. At this time, the seat belt retractor is in the

*

Be sure to follow the manufacturer’s instructions for

the proper use of your child restraint. Follow these

steps to install a rear-facing child restraint on the rear

seats using three-point type seat belt with automatic

locking mode:

and tug it forward to make sure that it is held

securely in place.

Automatic Locking Retractor (ALR) mode (child

restraint mode).

8. Check that the retractor is in the ALR mode by

trying to pull more of the seat belt out of the

retractor. If you cannot pull any more belt webbing

out of the retractor, the retractor is in the ALR

mode.

1

*

1. Position the child restraint on the seat

.

9. Check to make sure that the child restraint is

properly secured prior to each use. If the child

restraint is loose, repeat steps 4 through 8.

SSS0656A

Rear-facing: Step 4

4

4. Allow the seat belt to retract

. Pull up on the

*

shoulder belt to remove any slack in the belt.

SSS0654A

Rear-facing: Step 2

2. Route the seat belt tongue through the child

2

*

restraint and insert it into the buckle

hear and feel the latch engage.

until you

Safety — seats, seat belts and supplemental restraint system 1-19

mode.

8. Check to make sure that the child restraint is

properly secured prior to each use. If the child

restraint is loose, repeat steps 3 through 7.

SSS0639B

Rear-facing: Step 5

5. Remove any additional slack from the seat belt;

5

6

press downward

and rearward

firmly in

*

the center of the child restraint with your hand to

compress the vehicle seat cushion and seatback

while pulling up on the seat belt.

SSS0658B

Rear-facing: Step 6

6. Test the child restraint before you place the child

7

in it

. Push the child restraint from side to side

*

and tug it forward to make sure that it is held

securely in place.

7. Check that the retractor is in the ALR mode by

trying to pull more of the seat belt out of the

retractor. If you cannot pull any more belt webbing

out of the retractor, the retractor is in the ALR

1-20 Safety — seats, seat belts and supplemental restraint system

Installation on front passenger’s seat - seat belt without automatic locking mode

SSS0360C

Step 4

SSS0300A

4. Route the seat belt tongue through the child

3

restraint and insert it into the buckle

hear and feel the latch engage.

until you

*

Front-facing:

WARNING:

If you must install a front-facing child restraint system

on the front seat, follow these steps:

5. To prevent slack in the seat belt webbing, it is

necessary to secure the seat belt in place with

locking devices attached to the child restraint.

.

Never install a rear-facing child restraint on

the front passenger’s seat when the front

passenger’s air bag is available. Supple-

mental front-impact air bags inflate with

great force.

A

rear-facing child restraint

could be struck by the supplemental front-

impact air bags in an accident and could

seriously injure or kill your child.

.

Never install a child restraint with a top

tether strap on the front seat.

NISSAN recommends that a child restraint

be installed on the rear seat. However, if you

must install a child restraint on the front

passenger’s seat, move the passenger’s seat

to the rearmost position.

SSS0627

Steps 1 and 2

1

SSS0647B

1. Move the seat to the rearmost position

.

*

Step 6

2. Adjust the head restraint to its highest position

6. Remove any additional slack from the seat belt;

.

Child restraints for infants must be used in

the rear-facing direction and therefore must

not be used on the front passenger’s seat

when the front passenger’s air bag is avail-

able.

2

.

*

4

5

press downward

and rearward

firmly in

*

the center of the child restraint with your knee to

compress the vehicle seat cushion and seatback

while pulling up on the seat belt.

3. Position the child restraint in the seat.

Safety — seats, seat belts and supplemental restraint system 1-21

Installation on front passenger’s seat - seat belt with automatic locking mode

SSS0302G

Step 7

SSS0300A

7. Test the child restraint before you place the child

6

in it

. Push the child restraint from side to side

*

unsecured and cause injury to the child in a

sudden stop or collision.

and tug it forward to make sure that it is held

securely in place.

WARNING:

Never install rear-facing child restraint

system on the front seat. Inflating supple-

mental front-impact air bags inflate with

.

a

8. Check to make sure that the child restraint is

properly secured prior to each use. If the child

restraint is loose, repeat steps 4 through 7.

Front-facing:

great force.

A

rear-facing child restraint

system could be struck by the supplemental

front-impact air bags in an accident and

could seriously injure or kill your child.

NISSAN recommends that a child restraint

system be installed on the rear seat. How-

ever, if you must install a front-facing child

restraint system on the front passenger’s

seat, move the passenger’s seat to the

rearmost position.

SSS0627

Front-facing: Steps 1 and 2

.

Never install a child restraint system with a

top tether strap on the front seat.

Be sure to follow the manufacturer’s instructions for

the proper use of your child restraint. Follow these

steps to install a front-facing child restraint on the front

passenger’s seat using three-point type seat belt with

automatic locking mode:

Child restraint systems for infants must be

used in the rear-facing direction and there-

fore must not be used on the front seat.

.

Failure to use the seat belts will result in the

child restraint system not being properly

secured. It could tip over or otherwise be

1

*

1. Move the seat to the rearmost position

.

1-22 Safety — seats, seat belts and supplemental restraint system

2. Adjust the head restraint to its highest position

belt is not locked, repeat steps 5 through 8.

2

.

*

Place the ignition switch in the “ON” position. The

3. Position the front-facing child restraint in the front

passenger’s seat. It should be placed in the front-

facing direction only.

passenger air bag status light

should

illuminate. If this light does not illuminate, see

“Supplemental Restraint System (SRS)” (P.1-24).

Move the child restraint to another seating

position. Have the system checked by a NISSAN

dealer.

After the child restraint system is removed and the seat

belt is fully retracted, the automatic locking mode is

cancelled and returned to the emergency locking

mode.

SSS0424B

Front-facing: Step 6

5

6. Allow the seat belt to retract

. Pull up on the

shoulder belt to remove any slack in the belt.

*

SSS0360C

Front-facing: Step 4

4. Route the seat belt tongue through the child

3

*

restraint and insert it into the buckle

hear and feel the latch engage.

until you

SSS0302F

Front-facing: Step 7

7. Test the child restraint system before you place

the child in it. Tilt it from side to side. Try to tug it

forward and check if it is held securely in place.

8. Check that the retractor is in the ALR mode by

trying to pull more of the seat belt out of the

retractor. If you cannot pull any more belt webbing

out of the retractor, the retractor is in the ALR

mode.

SSS0361C

Front-facing: Step 5

5. Pull the shoulder belt until the belt is fully extended

4

*

. At this time, the seat belt retractor is in the

Automatic Locking Retractor (ALR) mode (child

restraint mode).

9. Check to make sure that the child restraint system

is properly secured prior to each use. If the seat

Safety — seats, seat belts and supplemental restraint system 1-23

Safety ? seats, seat belts and supplemental restraint system -> Child restraints for Your Nissan Juke SUV First Generation (2010-2019)

Related Topics

Popular Owner Manuals

Latest Owner Manuals