2004-2009 Nissan Micra 4 Door Maintenance and do-it-yourself -> Engine oil User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Maintenance and do-it-yourself -> Engine oil for Your Nissan Micra 4 Door Third Generation (2004-2009)

. Avoid direct skin contact with used coolant.
If skin contact is made, wash thoroughly
with soap or hand cleaner as soon as
possible.
. Keep coolant out of reach of children and
pets.
Engine coolant must be disposed of properly. Check
your local regulations.
GUID-8F1A0D6C-4AA2-4CD1-B6BD-AD8401C151B5
CHECKING ENGINE OIL LEVEL
GUID-5EEB94D4-2F6A-4CE2-9C2C-0FC29A70C671
SDI2572
HR12DDR, HR12DE and HR15DE engine
SDI2713
K9K engine
1. Park the vehicle on a level surface and apply the
parking brake.
2. Start the engine and warm it up until the engine
temperature reaches the normal operating tem-
perature (approximately 5 minutes).
3. Stop the engine.
4. Wait at least 10 minutes for the engine oil to drain
back to the oil pan.
5. Remove the dipstick and wipe it clean.
6. Reinsert the dipstick all the way.
7. Remove the dipstick and check the oil level. It
should be within the range
*
C
.
8. If the oil level is below
*
A
, remove the oil filler cap
and pour the recommended oil into the opening.
Do not overfill
*
B
.
For K9K engine model:
When filling the engine oil, do not remove
the dipstick.
9. Recheck the oil level with the dipstick.
It is normal to add some oil between oil
maintenance intervals or during the break-in
period, depending on the severity of operat-
ing conditions.
CAUTION:
The oil l evel should be checked regularly.
Operating your vehicle with an insufficient
amount of oil can damage the engine, and such
damage is not covered by warranty.
CHANGING ENGINE OIL AND OIL FILTER
GUID-BE8C324A-D859-4 863-B6BB-938109435039
WARNING:
. Used oil must be disposed of properly. Never
pour or dump oil into the ground, canals,
rivers, etc. It should be disposed of at proper
waste facilities. NISSAN recommends hav-
ing your oil changed by a NISSAN dealer.
. Be careful not to burn yourself, as the
engine oil may be hot.
. Prolonged and repeated contact with used
engine oil may cause skin cancer.
Maintenance and do-it-yourself 8-11
ENGINE OIL
8-12 Maintenance and do-it-yourself
. Avoid direct skin contact with used oil. If
contacted, wash thoroughly with soap or
hand cleaner and plenty of water as soon as
possible.
. Store used engine oil in marked containers
out of the reach of children.
CAUTION:
Waste oil must be disposed of properly. Check
your local regulations.
Engine oil replacement (HR12DDR, HR12DE
and HR15DE engine models)
GUID-F6B512B4-CCD6-4DB1-B9B6-6F08E9078146
JVM0059X
HR12DDR engine model
SDI2578
HR12DE engine model
JVM0001X
HR15DE engine model
1. Oil filler cap
2. Oil drain plug
3. Oil filter
1. Park the vehicle on a level surface and apply the
parking brake.
2. Start the engine and warm it up until the engine
temperature reaches the normal operating tem-
perature (approximately 5 minutes).
3. Stop the engine.
4. Wait at least 10 minutes for the engine oil to drain
back to the oil pan.
5. Place a large drain pan under the drain plug.
6. Remove the drain plug with a wrench.
7. Remove the oil filler cap and completely drain the
oil.
If the oil filter is to be changed, remove and
replace it at this time. (See “Engine oil filter
replacement (HR12DDR, HR12DE and HR15DE
engine models)” (P.8-13).)
8. Clean and reinstall the drain plug and new washer.
Securely tighten the drain plug with a wrench. Do
not use excessive force.
Drain plug tightening torque:
29 to 39 N·m
(3.0 to 4.0 kg-m, 22 to 29 ft-lb)
9. Refill the recommended engine oil and quantity.
(See “Recommended fuel/lubricants and capaci-
ties” (P.9-2).)
10. Securely install the oil filler cap.
11. Start the engine.
12. Check the drain plug for any sign of leakage.
13. Check the engine oil level according to the proper
procedure. (See “Checking engine oil level” (P.8-
11).)
Engine oil filter replacement (HR12DDR,
HR12DE and HR15DE engine models)
GUID-C6576475-3FF6-49AD-B361-FC5BFCA06FA1
JVM0059X
HR12DDR engine model
Maintenance and do-it-yourself 8-13
8-14 Maintenance and do-it-yourself
SDI2578
HR12DE engine model
JVM0001X
HR15DE engine model
1. Oil filler cap
2. Oil drain plug
3. Oil filter
1. Park the vehicle on a level surface and apply the
parking brake.
2. Turn the engine off.
3. Drain the engine oil according to the proper
procedure. (See “Engine oil replacement
(HR12DDR, HR12DE and HR15DE engine mod-
els)” (P.8-12).)
4. Loosen the oil filter with an oil filter wrench.
Depending on the engine model, a special cap
type wrench may be required. See a NISSAN
dealer for more information.
5. Remove the oil filter by turning it by hand.
6. Wipe the engine oil filter mounting surface with a
clean cloth.
Be sure to remove any old gasket remaining on the
mounting surface.
7. Apply the new engine oil to the gasket of the new
oil filter.
8. Screw in the oil filter until a slight resistance is felt,
and then tighten an additional 2/3 of turn to
secure the oil filter.
Oil filter tightening torque:
15 to 20 N·m (11 to 14 ft-lb)
9. Refill the engine oil. (See “Engine oil replacement
(HR12DDR, HR12DE and HR15DE engine mod-
els)” (P.8-12).)
10. Start the engine and check for leakage around the
oil filter. Correct as required.
11. Turn the engine off and wait several minutes.
12. Check the engine oil level according to the proper
procedure. (See “Checking engine oil level” (P.8-
11).)
Engine oil and filter replacement (K9K engine
model)
GUID-DB83B48C-F30F-4EEF-B4C0-FD3B0797231A
SDI2472
1. Oil drain plug
2. Oil filter
1. Place a large drain pan under the drain plug.
2. Remove the drain plug with a wrench.
3. Remove the oil filler cap and completely drain the
oil.
If the oil filter is to be changed, remove and
replace it at this time.
CAUTION:
Waste oil must be disposed of properly. Check
your local regulations.
4. Loosen the oil filter with an oil filter wrench.
5. Remove the oil filter by turning it by hand.
6. Wipe the entire oil filter mounting surface with a
clean cloth.
Be sure to remove any old gasket remaining on the
mounting surface.
7. Apply new engine oil to the gasket on the new oil
filter.
8. Screw in the oil filter until a slight resistance is felt,
and then tighten an additional 3/4 of a turn to
secure the filter.
Oil filter tightening torque:
16 to 20 N·m (1.6 to 2.0 kg-m, 12 to 15 ft-lb)
9. Clean and reinstall the drain plug and new washer.
Securely tighten the drain plug with a wrench. Do
not use excessive force.
Drain plug tightening torque:
16 to 24 N·m (1.6 to 2.4 kg-m, 12 to 18 ft-lb)
10. Refill the recommended engine oil and quantity.
(See “Recommended fuel/lubricants and capaci-
ties” (P.9-2).)
11. Securely install the oil filler cap.
12. Start the engine.
13. Check the drain plug and the oil filter for any sign
of leakage.
14. Dispose of the used oil in the proper manner.
Check your local regulations.
15. Check the engine oil level according to the proper
procedure. (See “Checking engine oil level” (P.8-
11).)
After operation
GUID-B636D33D-2A55-4466-A417-154FB64E0B77
1. Install the engine undercover (if removed) into
position as the following steps.
a. Pull the center of each plastic clip out.
b. Hold the engine undercover into position.
c. Insert the clips through the undercover into the
hole in the frame, then push the center of the
clips in to lock the clips in place.
d. Screw in the bolts, then tighten them.
2. Lower the vehicle carefully to the ground.
PROTECT ENVIRONMENT
GUID-70D58191-654F-487A-A9F7-F0B9E1A5A11B
It is illegal to pollute drains, watercourses and soil. Use
authorized waste collection facilities, including civil
amen ity sites and garages providing facilities for
disposal of used oil and used oil filters. If in doubt,
contact your local authority for advice on disposal.
The regulations concerning the pollution of the
environment will vary from country to country.
Maintenance and do-it-yourself 8-15

Related Topics

Popular Owner Manuals