2004-2009 Nissan Micra 4 Door Maintenance and do-it-yourself -> Lights User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Maintenance and do-it-yourself -> Lights for Your Nissan Micra 4 Door Third Generation (2004-2009)

NOTE:
The extended storage fuse switch is used for
long term vehicle storage. If the extended
storage fuse switch is broken, it is not necessary
to replace it. Remove the fuse from the switch
then replace only the fuse to the fuse box.
How to remove the extended storage fuse
switch:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
1. To remove the extended storage fuse switch, be
sure the ignition switch is in the “OFF” or “LOCK”
position.
2. Be sure the headlight switch is in the “OFF”
position.
3. Remove the fuse box cover.
4. Pinch the switch and pull it in the direction of the
arrow.
GUID-A9786891-967B-4E5D-B254-BD0AEA44B6C2
HEADLIGHTS
GUID-D443FAB0-D1E0-4FEF-97CE-A8E1AF34C408
Fog may temporarily form inside the lens of the exterior
lights in the rain or in a car wash. A temperature
difference between the inside and the outside of the
lens causes the fog. This is not a malfunction. If large
drops of water collect inside the lens, contact a
NISSAN dealer.
Replacing halogen headlight bulb
GUID-8FAAB6BB-DBBB-43B5-998B-E36C919D4BAB
The halogen headlight is a semi-sealed beam type
which uses replaceable headlight (halogen) bulbs.
They can be replaced from inside the engine compart-
ment without removing the headlight assembly.
CAUTION:
. High-pressure halogen gas is sealed inside
the bulb. The bulb may break if the glass
envelope is scratched or the bulb is dropped.
JVM0002X
Type A
Maintenance and do-it-yourself 8-29
LIGHTS
8-30 Maintenance and do-it-yourself
JVM0276X
Type B (example)
1. Disconnect the battery negative cable.
2. Disconnect the electrical connector
*
A
from the
rear end of the bulb.
3. Pull off the rubber cap
*
B
.
4. Push and turn the retaining pin
*
C
to loosen it.
5. Remove the headlight bulb. Do not shake or rotate
the bulb when removing it.
6. Install the new bulb in the reverse order of
removal.
CAUTION:
. When handling the bulb, do not touch the
glass envelope.
. Use the same number and wattage as
originally installed:
Halogen headlight model
High beam bulb: 60W (H4)
Low beam bulb: 55W (H4)
. Do not leave the bulb out of the headlight
reflector for a long period of time as dust,
moisture and smoke may enter the headlight
body and affe ct the performance of the
headlight.
Aiming adjustment is not necessary if only the bulbs
are replaced. When aiming adjustment is necessary,
contact a NISSAN dealer.
EXTERIOR LIGHTS
GUID-41757DAA-5563-407F-920A-8ABDF7A58431
Item Wattage (W)
Front turn signal light 21
Front clearance light 5
Front fog light (if equipped) 55
Side turn signal light 5
Rear combination lights
Turn signal light 21
Stop/Tail light LED* or 21/5
Reverse light (for Thailand,
Brunei, Hong Kong and
Micra for India)
16
Reverse light (except for
Thailand, Brunei, Hong
Kong and Micra for India)
21
Rear fog light (if equipped) 21
High-mounted stop light LED* or 16
License plate light
5
INTERIOR LIGHTS
GUID-DED7A3AD-46C8-4A5D-ADCC-3098DB04F1CA
Item Wattage (W)
Room light 5
Cargo light (if equipped) 5
*: See a NISSAN dealer for replacement.
Maintenance and do-it-yourself 8-31
8-32 Maintenance and do-it-yourself
LIGHT LOCATIONS
GUID-7C0B0CD8-3919-4C47-8B10-EE67946C8967
JVM0288X
Type A
1. Interior light
2. Front fog light (if equipped)
3. Front turn signal light
4. Clearance light (for Micra Active)
5. Clearance light (except for Micra Active)
6. Headlight
7. Side turn signal light
8. Stop/tail light
9. High-mounted stop light (Model without rear
spoiler)
10. High-mounted stop light (Model w ith rear
spoiler)
11. Rear turn signal light
12. Reverse light or Rear fog light (if equipped)*
13. License plate light
14. Cargo light (if equipped)
*: For the Left-Hand Drive (LHD) model. On the Right-
Hand Drive (RHD) model, the rear fog light is located
on the opposite side.
JVM0273X
Type B
1. Interior light
2. Front turn signal light
3. Front fog light (if equipped)
4. Clearance light
5. Headlight
6. Side turn signal light
7. Stop/tail light
8. High-mounted stop light (Model without rear
spoiler)
9. High-mounted sto p light (Model with rear
spoiler)
10. Rear turn signal light
11. Reverse light
12. Rear fog light (if equipped)
13. License plate light
14. Cargo light (if equipped)
Maintenance and do-it-yourself 8-33
JVM0006X
Front fog light (if equipped) (Type A)
JVM0282X
Front fog light (if equipped) (Type B)
JVM0100X
Side turn signal light
Maintenance and do-it-yourself 8-35
8-36 Maintenance and do-it-yourself
SDI2580
Rear combination light (Type A)
JVM0274X
Rear combination light (Type B)
JVM0275X
Rear combination light (Type C)
JVC0014X
License plate light (Type A)
JVM0108X
License plate light (Type B)
JVM0008X
High-mounted stop light (model with rear spoiler)
CAUTION:
Do not reuse the packing on the back of the
high-mounted stop light. When installing, the
packing must be replaced with a new one.
To replace the high-mounted stop light bulb:
1. Remove the light with a suitable tool.
2. Remove the bulb socket and then replace the
bulb.
Maintenance and do-it-yourself 8-37
8-38 Maintenance and do-it-yourself
3. Replace the packing
*
A
.
4. Install in the reverse order of removal.
JVM0281X
Rear fog light (if equipped)
SDI2391
Room light
JVM0007X
Cargo light (if equipped)
To replace the cargo light bulb (if equipped):
1. Remove the light
*
A
with a suitable tool.
2. Remove the cover
*
B
.
3. Replace the bulb.
LEGAL REQUIREMENT TO ADJUST HEADLIGHT BEAM
GUID-78812B4F-7F9C-4017-9BEC-93FA11A6D702
For India (Micra Active)
GUID-06BA61B4-97AA-4856-B244-78E2CD8BE973
JVM0289X
When the vehicle is driven in a country where the
driving lane is different to your home country, affix an
opaque sticker on the headlight.
1. Turn the ignition switch to the "OFF" position and
wait until the headlights cool down.
2. Prepare the stickers referring to the figure. Make
the stickers
*
A
that will be affixed to the surface
of t he right sid e hea dlight and the left side
headlight.
NOTE:
.
Use an opaque material that prevents the
light from passing through it.
.
Note that transparent materials do not
work effectively.
3. Affix the sticker by aligning the corner
*
B
of the
sticker with the position of the mark
*
C
that is
located on the surface of the headlight seen from
front.
Affix the sticker as illustrated by aligning the mark
*
C
with dividing lines
*
D
and
*
E
.
NOTE:
Align the mark
*
C
with the center mark
of the headlight bulb.
Maintenance and do-it-yourself 8-39
8-40 Maintenance and do-it-yourself
For India (except for Micra Active)
GUID-888C9AC4-68C5-4648-9FEC-AB6806625627
JVM0279X
When the vehicle is driven in a country where the
driving lane is different to your home country, affix an
opaque sticker on the headlight.
1. Turn the ignition switch to the "OFF" position and
wait until the headlights cool down.
2. Prepare the stickers referring to the figure. Make
the stickers
*
A
that will be affixed to the surface
of t he right sid e hea dlight and the left side
headlight.
NOTE:
.
Use an opaque material that prevents the
light from passing through it.
.
Note that transparent materials do not
work effectively.
3. Affix the sticker by aligning the corner
*
B
of the
sticker with the position of the mark
*
C
that is
located on the surface of the headlight seen from
front.
Affix the sticker as illustrated by aligning the mark
*
C
with dividing lines
*
D
and
*
E
.
NOTE:
Align the mark
*
C
with the center mark
of the headlight bulb.
For Thailand, Brunei and Hong Kong
GUID-B7C5B036-3820-4F38-851D-5B9F347E4C17
JVM0283X
When the vehicle is driven in a country where the
driving lane is different to your home country, affix an
opaque sticker on the headlight.
1. Turn the ignition switch to the "OFF" position and
wait until the headlights cool down.
2. Prepare the stickers referring to the figure. Make
the stickers
*
A
that will be affixed to the surface
of t he right sid e hea dlight and the left side
headlight.
NOTE:
.
Use an opaque material that prevents the
light from passing through it.
.
Note that transparent materials do not
work effectively.
3. Using a marker pen or similar, put a mark
*
C
on
the surface of the headlight that will be used as a
guide for attaching the sticker
*
A
to the head-
light. The mark
*
C
is placed 36 mm (1.42 inch) or
46 mm (1.81 inch) to the left of the mark
*
D
on
the surface of the headlight seen from front.
4. Affix the sticker by aligning the corner
*
B
of the
sticker with the position of the mark
*
C
.
Affix the sticker as illustrated by aligning the mark
*
C
with dividing lines
*
E
.
NOTE:
Align the mark
*
D
with the center mark
of the headlight bulb.
Maintenance and do-it-yourself 8-41

Related Topics

Popular Owner Manuals