Get Instruments and controls Guide for Nissan Micra 4 Door Fourth Generation (2010-2016)

2 Instruments and controls

Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Meters and gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Speedometer and odometer . . . . . . . . . . . . . . . . . . . . . 2-3

Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Trip computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Warning/indicator lights and audible reminders . . . . . . . 2-7

Checking bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Warning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Indicator lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10

Audible reminders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Security systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

NISSAN vehicle immobilizer system . . . . . . . . . . . . .2-13

Windshield wiper and washer switch . . . . . . . . . . . . . . .2-14

Switch operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

Rear window wiper and washer switch. . . . . . . . . . . . . . 2-16

Rear window defroster switch. . . . . . . . . . . . . . . . . . . . . . 2-16

Headlight and turn signal switch. . . . . . . . . . . . . . . . . . . . 2-17

Headlight control switch. . . . . . . . . . . . . . . . . . . . . . . . 2-17

Daytime running light system. . . . . . . . . . . . . . . . . . . . 2-18

Instrument brightness control . . . . . . . . . . . . . . . . . . . 2-18

Turn signal switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-19

Front fog lights (if so equipped) . . . . . . . . . . . . . . . . . 2-19

Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20

Vehicle Dynamic Control (VDC) off switch. . . . . . . . . . . 2-20

Power outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-21

Map pockets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21

Storage trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-22

Cup holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22

Soft bottle holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23

Glove box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23

Tonneau cover (if so equipped). . . . . . . . . . . . . . . . . . 2-23

Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24

Power windows (if so equipped) . . . . . . . . . . . . . . . . 2-24

Manual windows (if so equipped). . . . . . . . . . . . . . . . 2-26

Interior light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27

Luggage

compartment light. . . . . . . . . . . . . . . . . . . . . . . . 2-27

1. Headlight/turn signal switch (P. 2-17)

2. Driver’s supplemental air bag/horn

(P. 1-47, 2-20)

3. Meters and gauges (P. 2-3)

4. Windshield wiper/washer switch

(P. 2-14)

5. Center vents (P. 4-6)

6. Rear window and outside mirror (if so

equipped) defroster switch (P. 2-16)

7. Hazard warning flasher switch (P. 6-2)

8. Front passenger bag status light

(P. 1-49)

9. Climate controls (P. 4-7)

10. Audio system (P. 4-31, 4-23)

11. Passenger’s supplemental air bag

(P. 1-47)

12. Side vents (P. 4-6)

13. Electronic outside rearview mirror con-

trol switch (if so equipped) (P.3-15)

14. Vehicle Dynamic Control (VDC) off

switch (P. 2-20)

15. Fuel-filler lid release lever

(P. 3-11)/Hood release lever (P. 3-9)

16. Audio control switches (if so equipped)

(P.4-44)

17. Tilt steering (P. 3-13)

18. Ignition switch (P. 5-5)

19. Cruise control (if so equipped) (P.5-15)

20. Shift lever (P. 5-8)

21. Cup holders (P. 2-22)

22. Glove box (P. 2-23)

23. 12v power outlet (P. 2-21)

24. USB port (if so equipped) (P. 4-40)

Refer to the page number indicated in pa-

rentheses for operating details.

LIC2799

INSTRUMENT PANEL

2-2 Instruments and controls

1. Tachometer

2. Speedometer

3. Trip odometer reset switch/trip com-

puter mode

4. Instrument brightness control

5. Automatic Transmission (A/T) position

indicator (A/T models only)

6. Odometer/twin trip odometer/trip com-

puter

7. Fuel gauge

SPEEDOMETER AND ODOMETER

Speedometer

The speedometer indicates the vehicle speed.

LIC2283

LIC2118

METERS AND GAUGES

Instruments and controls 2-3

Odometer/Twin trip odometer

The odometer/twin trip odometer is displayed

when the ignition switch is placed in the ON

position.

The odometer

䊊

records the total distance the

vehicle has been driven.

The twin trip odometer

䊊

records the distance

of individual trips.

Changing the display:

Press the change button

䊊

to change the dis-

play as follows:

Odo → Trip A → Trip B → Ins fuel consumption →

Average fuel consumption → Cruising range or

(DTE) → Odo

For trip computer information, refer to “Trip com-

puter” in this section.

Resetting the trip odometer:

Press the change/reset button

䊊

for more than

1 second to reset the currently displayed trip

odometer to zero.

TACHOMETER

The tachometer indicates engine speed in revo-

lutions per minute (rpm). Do not rev the engine

into the red zone

䊊

CAUTION

When engine speed approaches the red

zone, shift to a higher gear or reduce en-

gine speed. Operating the engine in the

red zone may cause serious engine

damage.

LIC2119 LIC2107

2-4 Instruments and controls

FUEL GAUGE

The gauge indicates

䊊

the approximate fuel

level in the tank when the ignition switch is placed

in the ON position.

When one segment remains on the digital fuel

gauge, only one segment will blink. When no

segments remain on the digital fuel gauge, the

fuel gauge symbol and the scale will blink.

Refill the fuel tank before the gauge regis-

ters E (Empty).

The

indicates that the fuel-filler door is

located on the driver’s side of the vehicle.

CAUTION

● If the vehicle runs out of fuel, the

check engine light may come on. Refuel

as soon as possible. After a few driving

trips, the

light should turn off. If

the light remains on after a few driving

trips, have the vehicle inspected by a

NISSAN dealer.

● For additional information, refer to

“Malfunction Indicator Light (MIL)” in

this section.

TRIP COMPUTER

When the ignition switch is placed in the ON

position, modes of the trip computer can be

selected by pushing the trip computer

change/reset button

䊊

on the instrument panel

located near the speedometer. The following

modes can be selected in the display

䊊

● Instant fuel consumption

● Average fuel consumption

● Distance to empty

LIC2167 LIC2168

Instruments and controls 2-5

Instant fuel consumption

The instant fuel consumption mode shows the

instant fuel economy. The display updates in-

stantly when driving.

Average fuel consumption

The average fuel consumption mode shows the

average fuel consumption since the last reset.

Resetting is done by pressing the change/reset

button

䊊

for more than approximately 1 second.

Distance to empty

The distance to empty mode provides you with an

estimation of the distance that can be driven

before refueling. The range is constantly being

calculated, based on the amount of fuel in the fuel

tank and the actual fuel consumption.

The distance to empty includes a low range

warning feature: when the fuel level is low, the

distance to empty is automatically selected and

the digits blink in order to draw the driver’s atten-

tion. Press the trip computer change/reset button

䊊

if you wish to return to the mode that was

selected before the warning occurred.

When the fuel level drops even lower, the dis-

tance to empty will display (----).

Trip computer reset

Pressing the change/reset button for more than

3 seconds will reset all modes except Trip A and

distance to empty.

2-6 Instruments and controls

Anti-lock Braking System (ABS)

warning light

Low windshield-washer fluid

warning light

Front passenger air bag status

light

Vehicle Dynamic Control (VDC)

OFF indicator light

Brake warning light Power steering warning light High beam indicator light (blue)

Charge warning light

Seat belt warning light and

chime

Malfunction Indicator Light

(MIL)

Door open warning light

(if so equipped)

Supplemental air bag warning

light

Overdrive OFF indicator light

(A/T models only)

Engine oil pressure warning

light

Automatic Transmission posi-

tion indicator light (A/T models

only)

Security indicator light

High temperature warning light

Cruise main switch indicator

light (if so equipped)

Slip indicator light

or Low fuel warning

light

Front fog light indicator light

(if so equipped)

Turn signal/hazard indicator

lights

CHECKING BULBS

With all doors closed, apply the parking brake

and place the ignition switch the in the ON posi-

tion without starting the engine. The following

lights will come on:

, , , ,

If equipped, the following lights come on briefly

and then go off:

(red),

If any light fails to come on, it may indicate

a burned-out bulb or an open circuit in the

electrical system. Have the system repaired

promptly.

WARNING/INDICATOR LIGHTS AND

AUDIBLE REMINDERS

Instruments and controls 2-7

WARNING LIGHTS

Anti-lock Braking System

(ABS) warning light

When the ignition switch is placed in the ON

position, the Anti-lock Braking System (ABS)

warning light illuminates and then turns off. This

indicates the ABS is operational.

If the ABS warning light illuminates while the

engine is running, or while driving, it may indicate

the ABS is not functioning properly. Have the

system checked by a NISSAN dealer.

If an ABS malfunction occurs, the anti-lock func-

tion is turned off. The brake system then operates

normally, but without anti-lock assistance. For

additional information, refer to ⬙Brake system⬙ in

the ⬙Starting and driving⬙ section.

Brake warning light

This light functions for both the parking brake and

the foot brake systems.

Parking brake indicator

When the ignition switch is placed in the ON

position, the light comes on when the parking

brake is applied.

Low brake fluid warning light

When the ignition switch is placed in the ON

position, the light warns of a low brake fluid level.

If the light comes on while the engine is running

with the parking brake not applied, stop the ve-

hicle and perform the following:

1. Check the brake fluid level. Add brake fluid

as necessary. For additional information, re-

fer to “Brake fluid” in the “Maintenance and

do-it-yourself” section of this manual.

2. If the brake fluid level is correct, have the

warning system checked by a NISSAN

dealer.

Charge warning light

If this light comes on while the engine is running,

it may indicate the charging system is not func-

tioning properly. Turn the engine off and check

the generator belt. If the belt is loose, broken,

missing, or if the light remains on, see a NISSAN

dealer immediately.

CAUTION

Do not continue driving if the generator

belt is loose, broken or missing.

Door open warning light (if so

equipped)

This light comes on when any of the doors are not

closed securely while the ignition switch is in the

ON position.

Engine oil pressure warning

light

This light warns of low engine oil pressure. If the

light flickers or comes on during normal driving,

pull off the road in a safe area, stop the engine

immediately, and call a NISSAN dealer or other

authorized repair shop.

The engine oil pressure warning light is not

designed to indicate a low oil level. Use the

dipstick to check the oil level. For additional in-

formation, refer to “Engine oil” in the “Mainte-

nance and do-it-yourself” section of this manual.

CAUTION

Running the engine with the engine oil

pressure warning light on could cause se-

rious damage to the engine almost imme-

diately. Such damage is not covered by

warranty. Turn off the engine as soon as it

is safe to do so.

2-8 Instruments and controls

High temperature warning light

When the ignition switch is placed in the ON

position, the high temperature warning light illu-

minates and then turns off. This indicates that the

high temperature sensor in the engine coolant

system is operational.

CAUTION

If the high temperature warning light illu-

minates while the engine is running, it

may indicate the engine temperature is

extremely high. Stop the vehicle safely as

soon as possible. If the vehicle is over-

heated, continuing vehicle operation may

seriously damage the engine. For addi-

tional information, refer to “If your vehicle

overheats” in the “In case of emergency”

section.

or Low fuel warning

light

This light comes on when the fuel level in the fuel

tank is getting low. Refuel as soon as it is conve-

nient, preferably before the fuel gauge reaches E

(Empty). There will be a small reserve of fuel

in the tank when the fuel gauge reaches E

(Empty), showing no more fuel bars.

Low windshield-washer fluid

warning light

This light comes on when the windshield-washer

fluid is at a low level. Add windshield-washer

fluid, as necessary. For additional information,

refer to “Windshield-washer fluid” in the “Mainte-

nance and do-it-yourself” section of this manual.

Power steering warning light

WARNING

● If the engine is not running or is turned

off while driving, the power assist for

the steering will not work. Steering will

be harder to operate.

● When the power steering warning light

illuminates with the engine running,

there will be no power assist for the

steering. You will still have control of

the vehicle but the steering will be

harder to operate. Have the power

steering system checked by a NISSAN

dealer.

When the ignition switch is placed in the ON

position, the power steering warning light illumi-

nates. After starting the engine, the power steer-

ing warning light turns off. This indicates the

power steering system is operational.

If the power steering warning light illuminates

while the engine is running, it may indicate the

power steering system is not functioning properly

and may need servicing. Have the power steering

system checked by a NISSAN dealer.

When the power steering warning light illumi-

nates with the engine running, there will be no

power assist for the steering but you will still have

control of the vehicle. At this time, greater steer-

ing effort is required to operate the steering

wheel, especially in sharp turns and at low

speeds.

For additional information, refer to “Power steer-

ing” in the “Starting and driving” section.

Seat belt warning light and

chime

The light and chime remind you to fasten your

seat belts. The light illuminates whenever the

ignition switch is placed in the ON or START

position and remains illuminated until the driver’s

seat belt is fastened. At the same time, the chime

sounds for about 6 seconds unless the driver’s

seat belt is securely fastened.

The seat belt warning light may also illuminate if

the front passenger’s seat belt is not fastened

when the front passenger’s seat is occupied . For

7 seconds after the ignition switch is placed in

Instruments and controls 2-9

the ON position, the system does not activate the

warning light for the front passenger.

For additional information, refer to “Seat belts” in

the “Safety—Seats, seat belts and supplemental

restraint system” section of this manual for pre-

cautions on seat belt usage.

Supplemental air bag warning

light

When the ignition switch is placed in the ON or

START position, the supplemental air bag warn-

ing light illuminates for about 7 seconds and then

turns off if the SRS air bag systems are opera-

tional. This means the system is operational.

If any of the following conditions occur, the

supplemental front air bags and/or pretensioner

systems need servicing and your vehicle must be

taken to a NISSAN dealer:

● The supplemental air bag warning light re-

mains on after approximately 7 seconds.

● The supplemental air bag warning light

flashes intermittently.

● The supplemental air bag warning light does

not come on at all.

Unless checked and repaired, the supplemental

restraint systems (air bag systems) may not func-

tion properly. For additional information, refer to

“Supplemental restraint system” in the “Safety—

Seats, seat belts and supplemental restraint sys-

tem” section of this manual.

WARNING

If the supplemental air bag warning light

is on, it could mean that the supplemental

front air bag and/or pretensioner systems

will not operate in an accident. To help

avoid injury to yourself or others, have

your vehicle checked by a NISSAN dealer

as soon as possible.

INDICATOR LIGHTS

Automatic transmission

position indicator light (A/T

models only)

When the ignition switch is in the ON position,

this indicator light shows the shift lever position.

For additional information, refer to “Driving the

vehicle” in the “Starting and driving” section of

this manual.

Cruise main switch indicator

light (if so equipped)

The light comes on when the cruise control main

switch is pushed. The light goes out when the

main switch is pushed again. When the cruise

main switch indicator light comes on, the cruise

control system is operational.

For additional information, refer to “Cruise con-

trol” in the “Starting and driving” section of this

manual.

Front fog light indicator light (if

so equipped)

The front fog light indicator light illuminates when

the front fog lights are ON. For additional infor-

mation, refer to “Front fog lights” in this section.

Front passenger air bag status

light

The front passenger air bag status light will be lit

and the passenger front air bag will be OFF

depending on how the front passenger seat is

being used.

For front passenger air bag status light operation,

refer to “Front passenger air bag and status light”

in the “Safety — Seats, seat belts and supple-

mental restraint system” section of this manual.

High beam indicator light

(blue)

This blue light comes on when the headlight high

beams are on and goes out when the low beams

are selected.

2-10 Instruments and controls

The high beam indicator light also comes on

when the passing signal is activated.

Malfunction Indicator Light

(MIL)

If this indicator light comes on steady or blinks

while the engine is running, it may indicate a

potential emission control malfunction.

The

may also come on steady if the fuel-

filler cap is loose or missing, or if the vehicle runs

out of fuel. Check to make sure the fuel-filler cap

is installed and closed tightly, and that the vehicle

has at least 3 gal (11.4 L) of fuel in the fuel tank.

After a few driving trips, the

light should

turn off if no other potential emission control

system malfunction exists.

If this indicator light comes on steady for 20 sec-

onds and then blinks for 10 seconds when the

engine is not running, it indicates that the vehicle

is not ready for an emission control system

inspection/maintenance test. For additional infor-

mation, refer to “Readiness for

inspection/maintenance (I/M) test” in the “Tech-

nical and consumer information” section of this

manual.

Operation

The MIL will come on in one of two ways:

● MIL on steady — An emission control system

malfunction has been detected. Check the

fuel-filler cap. If the LOOSE FUEL CAP

warning message is displayed in the odom-

eter, and the fuel-filler cap is loose or miss-

ing, tighten or install the cap and continue to

drive the vehicle. The

light should turn

off after a few driving trips. If the

light

does not turn off after a few driving trips,

have the vehicle inspected by a NISSAN

dealer. You do not need to have your vehicle

towed to the dealer.

● MIL blinking — An engine misfire has been

detected which may damage the emission

control system. To reduce or avoid emission

control system damage:

– do not drive at speeds above 45 MPH

(72 km/h);

– avoid hard acceleration or deceleration;

– avoid steep uphill grades;

– if possible, reduce the amount of cargo

being hauled.

The MIL may stop blinking and come on steady.

Have the vehicle inspected by a NISSAN dealer.

You do not need to have your vehicle towed to the

dealer.

CAUTION

Continued vehicle operation without hav-

ing the emission control system checked

and repaired as necessary could lead to

poor driveability, reduced fuel economy,

and possible damage to the emission con-

trol system.

Overdrive OFF indicator light

(A/T models only)

This light comes on when the overdrive function

is OFF.

The automatic transmission overdrive function is

controlled by the overdrive switch.

For additional information, refer to “Driving the

vehicle” in the “Starting and driving” section of

this manual.

Security indicator light

This light blinks whenever the ignition switch is

placed in the LOCK, OFF or ACC position. This

function indicates the security system equipped

on the vehicle is operational.

Instruments and controls 2-11

For additional information, refer to “Security sys-

tems” in this section.

Slip indicator light

This indicator will blink when the Vehicle Dynamic

Control (VDC) system or the Traction Control

System (TCS) is operating, thus alerting that the

vehicle is nearing its traction limits. The road

surface may be slippery.

Turn signal/hazard indicator

lights

The appropriate light flashes when the turn signal

switch is activated.

Both lights flash when the hazard switch is turned

on.

Vehicle Dynamic Control

(VDC) OFF indicator light

This indicator light comes on when the VDC off

switch is pushed to OFF. This indicates the VDC

system is not operating.

Push the VDC off switch again or restart the

engine and the system will operate normally. For

additional information, refer to “Vehicle Dynamic

Control (VDC) system” in the “Starting and driv-

ing” section of this manual.

The VDC light also comes on when you place the

ignition switch in the ON position. The light will

turn off after about 2 seconds if the system is

operational. If the light stays on or comes on

along with the

indicator light while you are

driving, have the VDC system checked by a

NISSAN dealer.

While the VDC system is operating, you might

feel slight vibration or hear the system working

when starting the vehicle or accelerating, but this

is normal.

AUDIBLE REMINDERS

Brake pad wear warning

The disc brake pads have audible wear warnings.

When a disc brake pad requires replacement, it

makes a high pitched scraping sound when the

vehicle is in motion, whether or not the brake

pedal is depressed. Have the brakes checked as

soon as possible if the warning sound is heard.

Key reminder chime

A chime sounds if the driver’s door is opened

while the key is left in the ignition switch. Remove

the key and take it with you when leaving the

vehicle.

Light reminder chime

With the ignition switch placed in the OFF posi-

tion, a chime sounds when the driver’s door is

opened if the headlights or parking lights are on.

Turn the headlight control switch off before leav-

ing the vehicle.

Parking brake reminder chime

A chime sounds if the parking brake is set and the

vehicle is driven. The chime will stop if the parking

brake is released or the vehicle speed returns to

zero.

2-12 Instruments and controls

Your vehicle has a security system:

● NISSAN Vehicle Immobilizer System

NISSAN VEHICLE IMMOBILIZER

SYSTEM

The NISSAN Vehicle Immobilizer System will not

allow the engine to start without the use of a

registered key.

If the engine fails to start using a registered key

(for example, when interference is caused by

another registered key, an automated toll road

device or automatic payment device on the key

ring), restart the engine using the following pro-

cedures:

1. Leave the ignition switch placed in the ON

position for approximately 5 seconds.

2. Place the ignition switch in the OFF or

LOCK position, and wait approximately

10 seconds.

3. Repeat steps 1 and 2.

4. Restart the engine while holding the device

(which may have caused the interference)

separate from the registered key.

If the no start condition re-occurs, NISSAN rec-

ommends placing the registered key on a sepa-

rate key ring to avoid interference from other

devices.

FCC Notice:

For USA:

This device complies with part 15 of the

FCC Rules. Operation is subject to the fol-

lowing two conditions: (1) This device may

not cause harmful interference, and (2) this

device must accept any interference re-

ceived, including interference that may

cause undesired operation.

NOTE:

Changes or modifications not expressly ap-

proved by the party responsible for compli-

ance could void the user’s authority to op-

erate the equipment.

For Canada:

This device complies with Industry Canada

licence-exempt RSS standard(s). Opera-

tion is subject to the following two condi-

tions: (1) this device may not cause inter-

ference, and (2) this device must accept any

interference, including interference that

may cause undesired operation of the de-

vice.

LIC0301

SECURITY SYSTEMS

Instruments and controls 2-13

Security indicator light

The security indicator light blinks whenever the

ignition switch is placed in the LOCK, OFF or

ACC position. This function indicates the

NISSAN Vehicle Immobilizer System is opera-

tional.

If the NISSAN Vehicle Immobilizer System is mal-

functioning, the light will remain on while the

ignition switch is placed in the ON position.

If the light still remains on and/or the en-

gine will not start, see a NISSAN dealer for

NISSAN Vehicle Immobilizer System ser-

vice as soon as possible. Please bring all

registered keys that you have when visiting

your NISSAN dealer for service.

SWITCH OPERATION

The windshield wiper and washer operates when

the ignition switch is in the ON position.

Push the lever down to operate the wiper at the

following speed:

䊊

Intermittent (INT) — intermittent operation

can be adjusted by turning the knob toward

䊊

(Slower) or

䊊

(Faster). Also, the inter-

mittent operation speed varies in accor-

dance with the vehicle speed. (For example,

when the vehicle speed is high, the intermit-

tent operation speed will be faster.)

LIC0474

Type A (if so equipped)

LIC2130

WINDSHIELD WIPER AND WASHER

SWITCH

2-14 Instruments and controls

䊊

Low (LO) — continuous low speed operation

䊊

High (HI) — continuous high speed opera-

tion

Push the lever up

䊊

to have one sweep opera-

tion (MIST ) of the wiper.

Pull the lever toward you

䊊

to operate the

washer. The wiper will also operate several times.

WARNING

In freezing temperatures the washer solu-

tion may freeze on the windshield and

obscure your vision which may lead to an

accident. Warm the windshield with the

defroster before you wash the windshield.

CAUTION

● Do not operate the washer continuously

for more than 30 seconds.

● Do not operate the washer if the reser-

voir is empty.

● Do not fill the windshield-washer fluid

reservoir with washer fluid concen-

trates at full strength. Some methyl al-

cohol based washer fluid concentrates

may permanently stain the grille if

spilled while filling the windshield-

washer fluid reservoir.

● Pre-mix windshield-washer fluid con-

centrates with water to the manufactur-

er’s recommended levels before pour-

ing the fluid into the windshield-washer

fluid reservoir. Do not use the

windshield-washer fluid reservoir to

mix the windshield-washer fluid con-

centrate and water.

Type B (if so equipped)

LIC2131

Type C (if so equipped)

LIC2789

Instruments and controls 2-15

The rear window wiper and washer operate when

the ignition switch is placed in the ON position.

Turn the switch clockwise from the OFF position

to operate the wiper.

䊊

Intermittent (INT) – intermittent operation

(not adjustable)

䊊

ON – continuous low speed operation

Push the switch forward

䊊

to operate the

washer. The wiper will also operate several times.

WARNING

In freezing temperatures the washer solu-

tion may freeze on the window and ob-

scure your vision. Warm the rear window

with the defroster before you wash the

rear window.

CAUTION

● Do not operate the washer continuously

for more than 30 seconds.

● Do not operate the washer if the reser-

voir tank is empty.

● Do not fill the windshield-washer fluid

reservoir tank with washer fluid concen-

trates at full strength. Some methyl al-

cohol based washer fluid concentrates

may permanently stain the grille if

spilled while filling the windshield-

washer fluid reservoir tank.

● Pre-mix washer fluid concentrates with

water to the manufacturer’s recom-

mended levels before pouring the fluid

into the windshield-washer fluid reser-

voir tank. Do not use the windshield-

washer fluid reservoir tank to mix the

washer fluid concentrate and water.

LIC2398

Type A (if so equipped)

LIC2116

REAR WINDOW WIPER AND

WASHER SWITCH

REAR WINDOW DEFROSTER SWITCH

2-16 Instruments and controls

To defrost the rear window glass, start the engine

and push the rear window defroster switch on.

The rear window defroster indicator light on the

switch comes on. Push the switch again to turn

the defroster off.

The rear window defroster automatically turns off

after approximately 15 minutes.

CAUTION

When cleaning the inner side of the rear

window, be careful not to scratch or dam-

age the rear window defroster.

HEADLIGHT CONTROL SWITCH

Lighting

䊊

When turning the switch to the

posi-

tion, the front parking, tail, license plate and

instrument panel lights come on.

䊊

When turning the switch to the

posi-

tion, the headlights come on and all the other

lights remain on.

CAUTION

Use the headlights with the engine run-

ning to avoid discharging the vehicle

battery.

Type B (if so equipped)

LIC2110

LIC2127

HEADLIGHT AND TURN SIGNAL

SWITCH

Instruments and controls 2-17

Headlight beam select

䊊

To select the high beam function, push the

lever forward. The high beam lights come on

and the

light illuminates.

䊊

Pull the lever back to select the low beam.

䊊

Pulling and releasing the lever flashes the

headlight high beams on and off.

Battery saver system

If the ignition switch is placed in the OFF position

while the headlight switch is in the

or position, the headlights will turn off after

a period of time.

CAUTION

Even though the battery saver feature au-

tomatically turns off the headlights after a

period of time, you should turn the head-

light switch to the OFF position when the

engine is not running to avoid discharging

the vehicle battery.

DAYTIME RUNNING LIGHT SYSTEM

The headlights automatically illuminate at a re-

duced intensity when the engine is started with

the parking brake released. The daytime running

lights operate with the headlight switch in the

OFF position. Turn the headlight switch to

the

or position for full illumination

when driving at night.

If the parking brake is applied before the engine is

started, the daytime running lights do not illumi-

nate. The daytime running lights illuminate when

the parking brake is released. The daytime run-

ning lights will remain on until the ignition switch

is placed in the OFF position.

WARNING

When the daytime running light system is

active, tail lights on your vehicle are not

on. It is necessary at dusk to turn on your

headlights. Failure to do so could cause

an accident injuring yourself and others.

INSTRUMENT BRIGHTNESS

CONTROL

The instrument brightness control operates when

the headlight control switch is in the

or position.

Push the control

䊊

to adjust the brightness of

instrument panel lights when driving at night.

When the ignition is on and the knob is pushed,

the illumination decreases. The brightness will

return to the maximum level when the brightness

is at its minimum and the knob is pushed.

LIC2128 LIC2147

2-18 Instruments and controls

TURN SIGNAL SWITCH

Turn signal

䊊

Move the lever up or down to signal the

turning direction. When the turn is com-

pleted, the turn signal cancels automatically.

Lane change signal

䊊

Move the lever up or down until the turn

signal begins to flash, but the lever does not

latch, to signal a lane change. Hold the lever

until the lane change is completed.

Move the lever up or down until the turn

signal begins to flash, but the lever does not

latch, and release the lever. The turn signal

will automatically flash three times.

Choose the appropriate method to signal a lane

change based on road and traffic conditions.

FRONT FOG LIGHTS (if so equipped)

To turn the front fog lights on, turn the headlight

switch to the

or position, then turn

the fog light switch to the

position.

To turn them off, turn the fog light switch to the

OFF position.

WIC1512 WIC1440

Instruments and controls 2-19

To sound the horn, push near the horn icon on the

steering wheel.

WARNING

Do not disassemble the horn. Doing so

could affect proper operation of the

supplemental front air bag system. Tam-

pering with the supplemental front air bag

system may result in serious personal

injury.

The vehicle should be driven with the VDC sys-

tem on for most driving conditions.

If the vehicle is stuck in mud or snow, the VDC

system reduces the engine output to reduce

wheel spin. The engine speed will be reduced

even if the accelerator is depressed to the floor. If

maximum engine power is needed to free a stuck

vehicle, turn the VDC system off.

To turn off the VDC system, push the VDC OFF

switch. The

indicator will come on.

Push the VDC OFF switch again or restart the

engine to turn on the system. For additional infor-

mation, refer to “Vehicle Dynamic Control (VDC)

system” in the “Starting and driving” section of

this manual.

LIC2122 LIC1548

HORN VEHICLE DYNAMIC CONTROL (VDC)

OFF SWITCH

2-20 Instruments and controls

The power outlet is for powering electrical acces-

sories such as cellular telephones. The outlet is

rated at 12 volt, 120W (10A) maximum.

CAUTION

● The outlet and plug may be hot during

or immediately after use.

● Only certain power outlets are designed

for use with a cigarette lighter unit. Do

not use any other power outlet for an

accessory lighter. See your NISSAN

dealer for additional information.

● Do not use with accessories that exceed

a 12 volt, 120W (10A) power draw. Do

not use double adapters or more than

one electrical accessory.

● Use power outlets with the engine run-

ning to avoid discharging the vehicle

battery.

● Avoid using power outlets when the air

conditioner (if so equipped), headlights

or rear window defroster (if so

equipped) is on.

● Before inserting or disconnecting a

plug, be sure the electrical accessory

being used is turned OFF.

● Push the plug in as far as it will go. If

good contact is not made, the plug may

overheat or the internal temperature

fuse may open.

● When not in use, be sure to close the

cap. Do not allow water or any other

liquid to contact the outlet.

MAP POCKETS

LIC2715 LIC0799

POWER OUTLET STORAGE

Instruments and controls 2-21

STORAGE TRAYS

WARNING

Do not place sharp objects in the trays to

help prevent injury in an accident or sud-

den stop.

CUP HOLDERS

CAUTION

● Avoid abrupt starting and braking when

the cup holder is being used to prevent

spilling the drink. If the liquid is hot, it

can scald you or your passenger.

● Use only soft cups in the cup holder.

Hard objects can injure you in an

accident.

Storage compartment

LIC2742

Front

LIC2743

Rear

SIC4409

2-22 Instruments and controls

SOFT BOTTLE HOLDER

CAUTION

● Do not use bottle holder for any other

objects that could be thrown about in

the vehicle and possibly injure people

during sudden braking or an accident.

● Do not use bottle holder for open liquid

containers.

GLOVE BOX

Open the glove box by pulling the handle.

WARNING

Keep glove box lid closed while driving to

help prevent injury in an accident or a

sudden stop.

TONNEAU COVER (if so equipped)

WARNING

● Never put anything on the cargo cover,

no matter how small. Any object on it

could cause an injury in an accident or a

sudden stop.

● Do not put objects heavier than 20 kg

(44 lbs) on the cargo cover for long

periods of time.

● Do not leave the cargo cover in the

vehicle with it disengaged from the

holder.

● Properly secure all cargo with ropes or

straps to help prevent it from sliding or

shifting. Do not place cargo higher than

the seatbacks. In a sudden stop or col-

lision, unsecured cargo could cause

personal injury.

The cargo cover keeps the luggage compartment

contents hidden from the outside.

Front

LIC2801

LIC2160

Instruments and controls 2-23

To remove the cargo cover:

䊊

Remove the cargo cover holders from the

rear pillar.

䊊

Rotate the cargo cover to one side.

䊊

Remove cargo cover without touching sur-

rounding parts.

To insert the cargo cover:

䊊

Insert cargo cover rotated without touching

surrounding parts.

䊊

Let cargo cover rest over tool box.

䊊

Insert cargo cover.

POWER WINDOWS (if so equipped)

WARNING

● Make sure that all passengers have

their hands, etc. inside the vehicle while

it is in motion and before closing the

windows. Use the window lock switch to

prevent unexpected use of the power

windows.

● Do not leave children unattended inside

the vehicle. They could unknowingly ac-

tivate switches or controls and become

trapped in a window. Unattended chil-

dren could become involved in serious

accidents.

LIC2775 LIC2774

WINDOWS

2-24 Instruments and controls

1. Window lock button

2. Power door lock switch

3. Front passenger’s side window switch

4. Right rear passenger’s window switch

5. Left rear passenger’s window switch

6. Driver’s side automatic switch

Driver’s side power window switch

The driver’s side control panel is equipped with

switches to open or close the front and rear

passenger windows.

To open a window, push the switch and hold it

down. To close a window, pull the switch and

hold it up. To stop the opening or closing function

at any time, simply release the switch.

Front passenger’s power window

switch

The passenger’s window switch operates only

the corresponding passenger’s window. To open

the window, push the switch and hold it down

䊊

To close the window, pull the switch up

䊊

WIC0872 LIC0718

Instruments and controls 2-25

Rear power window switch

The rear power window switches open or close

only the corresponding windows. To open the

window, push the switch and hold it down

䊊

. To

close the window, pull the switch up

䊊

Locking passengers’ windows

When the window lock switch is depressed, only

the driver’s side window can be opened or

closed. Push it again to cancel the window lock

function.

When power window switch does not

operate

If the power window automatic function (closing

only) does not operate properly, perform the fol-

lowing procedure to initialize the power window

system.

1. Place the ignition switch in the ON position.

2. Open the window more than halfway by

operating the power window switch.

3. Pull up and hold the window switch and hold

it to close the window and then hold the

switch for more than 3 seconds after the

window is closed completely.

4. Release the power window switch. Operate

the window by automatic function to confirm

the initialization is complete.

If the power window automatic function does not

operate properly after performing the above pro-

cedure, see a NISSAN dealer for assistance.

MANUAL WINDOWS (if so equipped)

The side windows can be opened or closed by

turning the hand crank on each door.

LIC0718 WIC0263

2-26 Instruments and controls

The interior light has a three-position switch and

operates regardless of ignition switch position.

When the switch is in the ON position

䊊

, the

interior lights illuminate, regardless of door posi-

tion. The lights will go off after a period of time

unless the ignition switch is placed in the ACC or

ON position (if so equipped).

When the switch is in the DOOR position

䊊

, the

interior lights will stay on for a period of time

when:

● The doors are unlocked by the key fob, a key

or the power door lock switch while all doors

are closed and the ignition switch is placed

in the OFF position.

● The driver’s door is opened and then closed

while the key is removed from the ignition

switch.

● The key is removed from the ignition switch

while all doors are closed.

The lights will turn off while the timer is activated

when:

● The driver’s door is locked by the key fob, a

key, or the power door lock switch.

● The ignition switch is placed in the ON po-

sition.

When the switch is in the OFF position

䊊

, the

interior lights do not illuminate, regardless of door

position.

The lights will turn off automatically after a period

of time while doors are open to prevent the bat-

tery from becoming discharged.

CAUTION

Do not use for extended periods of time

with the engine stopped. This could result

in a discharged battery.

The light illuminates when the rear hatch is

opened. When the rear hatch is closed, the light

will turn off.

The light also illuminates with other interior lights

when the interior light switch is in the DOOR

position. For additional information, refer to “Inte-

rior light” in this section.

LIC2126

INTERIOR LIGHT LUGGAGE COMPARTMENT LIGHT

Instruments and controls 2-27

MEMO

2-28 Instruments and controls

Instruments and controls for Your Nissan Micra 4 Door Fourth Generation (2010-2016)

Related Topics

Popular Owner Manuals

Latest Owner Manuals