2017-2023 Nissan Micra 4 Door Instruments and controls -> Warning lights, indicator lights and audible reminders User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Instruments and controls -> Warning lights, indicator lights and audible reminders for Your Nissan Micra 4 Door Fifth Generation (2017-2023)

WARNING LIGHTS, INDICATOR LIGHTS  
AND AUDIBLE REMINDERS  
Anti-lock Braking System (ABS) warning  
light  
Power steering warning light (if so  
equipped)  
High beam indicator light (blue)  
Malfunction Indicator Light (MIL)  
Brake warning light  
Charge warning light  
Seat belt warning light and chime  
Supplemental air bag warning light  
Overdrive OFF indicator light (A/T models  
only)  
Automatic Transmission position indica-  
tor light (A/T models only)  
Door open warning light  
Security indicator light  
Slip indicator light  
Engine oil pressure warning light  
High temperature warning light (red)  
CRUISE indicator light (if so equipped)  
Front fog light indicator light (if so  
equipped)  
Turn signal/hazard indicator lights  
Vehicle Dynamic Control (VDC) OFF indi-  
cator light  
Low windshield-washer fluid warning light  
Front passenger air bag status light  
The following lights (if so equipped) will  
come on briefly and then go off:  
recommended that you visit a NISSAN  
dealer for this service.  
CHECKING LIGHTS  
With all doors closed, apply the parking  
brake, fasten the seat belts and place the  
ignition switch in the ON position without  
starting the engine. The following lights (if  
so equipped) will come on:  
Some indicators and warnings are also dis-  
played in the trip computer located to the  
right of the speedometer. For additional  
information, refer to “Meters and gauges” in  
this section.  
,
,
,
,
,
If any light fails to come on or operate in a  
way other than described, it may indicate a  
burned-out bulb and/or a system mal-  
function. Have the system checked. It is  
,
,
,
,
,
2-8 Instruments and controls  
Parking brake indicator  
WARNING LIGHTS  
∙ Pressing the brake pedal with the en-  
gine stopped and/or a low brake fluid  
level may increase your stopping dis-  
tance and braking will require greater  
pedal effort as well as pedal travel.  
When the ignition switch is placed in the ON  
position, the light comes on when the park-  
ing brake is applied.  
This vehicle has various warning lights that  
may illuminate to indicate a potential prob-  
lem. For additional information, refer to the  
specific light in this section.  
Low brake fluid warning light  
∙ If the brake fluid level is below the  
MINIMUM or MIN mark on the brake  
fluid reservoir, do not drive until the  
brake system has been checked. It is  
recommended that you visit a NISSAN  
dealer for this service.  
Anti-lock Braking System  
(ABS) warning light  
When the ignition switch is placed in the ON  
position, the ABS warning light illuminates  
and then turns off. This indicates the ABS is  
operational.  
When the ignition switch is placed in the ON  
position, the light warns of a low brake fluid  
level. If the light comes on while the engine is  
running with the parking brake not applied,  
stop the vehicle and perform the following:  
1. Check the brake fluid level. Add brake  
fluid as necessary. For additional infor-  
mation, refer to “Brake fluid” in the “Do-  
it-yourselfsection of this manual.  
Charge warning light  
If the ABS warning light illuminates while  
the engine is running or while driving, it  
may indicate the ABS is not functioning  
properly. Have the system checked. It is  
recommended that you visit a NISSAN  
dealer for this service.  
If this light comes on while the engine is  
running, it may indicate the charging sys-  
tem is not functioning properly. Turn the  
engine off and check the generator belt. If  
the belt is loose, broken, or missing, or if the  
light remains on, have the system checked.  
It is recommended that you visit a NISSAN  
dealer for this service.  
2. If the brake fluid level is correct, have  
the warning system checked. It is rec-  
ommended that you visit a NISSAN  
dealer for this service.  
If an ABS malfunction occurs, the anti-lock  
function is turned off. The brake system  
then operates normally but without anti-  
lock assistance. For additional information,  
refer to “Brake system” in the “Starting and  
driving” section of this manual.  
WARNING  
Your brake system may not be working  
properly if the warning light is on. Driv-  
ing could be dangerous. If you judge it  
to be safe, drive carefully to the nearest  
service station for repairs. Otherwise,  
have your vehicle towed because driv-  
ing it could be dangerous.  
CAUTION  
Do not continue driving if the generator  
belt is loose, broken or missing.  
Brake warning light  
This light functions for both the parking  
brake and the foot brake systems.  
Instruments and controls 2-9  
Door open warning light  
High temperature warning  
light (red)  
When the ignition switch is placed in the ON  
position, the high temperature warning light  
illuminates and then turns off. This indicates  
that the high temperature sensor in the en-  
gine coolant system is operational.  
Power steering warning  
light (if so equipped)  
This light comes on when any of the doors  
are not closed securely while the ignition  
switch is placed in the ON position.  
WARNING  
∙ If the engine is not running or is  
turned off while driving, the power as-  
sist for the steering will not work.  
Steering will be harder to operate.  
Engine oil pressure  
warning light  
This light warns of low engine oil pressure. If  
the light flickers or comes on during nor-  
mal driving, pull off the road in a safe area,  
stop the engine immediately and call a  
NISSAN dealer or other authorized repair  
shop.  
CAUTION  
∙ When the power steering warning  
light illuminates with the engine run-  
ning, there will be no power assist for  
the steering. You will still have control  
of the vehicle, but the steering will be  
harder to operate. Have the power  
steering system checked. It is recom-  
mended that you visit a NISSAN dealer  
for this service.  
When the ignition switch is placed in the ON  
position, the power steering warning light  
illuminates. After starting the engine, the  
power steering warning light turns off. This  
indicates the power steering is operational.  
If the high temperature warning light  
illuminates while the engine is running,  
it may indicate the engine temperature  
is extremely high. Stop the vehicle  
safely as soon as possible. If the vehicle  
is overheated, continuing vehicle op-  
eration may seriously damage the en-  
gine. For additional information, refer  
to “If your vehicle overheats” in the “In  
case of emergency” section of this  
manual.  
The engine oil pressure warning light is  
not designed to indicate a low oil level.  
Use the dipstick to check the oil level. For  
additional information, refer to “Engine oil”  
in the “Do-it-yourselfsection of this  
manual.  
Low windshield-washer  
fluid warning light  
CAUTION  
Running the engine with the engine oil  
pressure warning light on could cause  
serious damage to the engine almost  
immediately. Such damage is not cov-  
ered by the NISSAN New Vehicle Limited  
Warranty. Turn off the engine as soon as  
it is safe to do so.  
If the power steering warning light illumi-  
nates while the engine is running, it may  
indicate the power steering is not function-  
ing properly and may need servicing. Have  
the power steering checked. It is recom-  
mended that you visit a NISSAN dealer for  
this service.  
This light comes on when the windshield-  
washer fluid is at  
a
low level. Add  
windshield-washer fluid as necessary. For  
additional information, refer to “Windshield-  
washer fluid” in the “Do-it-yourselfsection  
of this manual.  
2-10 Instruments and controls  
When the power steering warning light illu-  
minates with the engine running, there will  
be no power assist for the steering, but you  
will still have control of the vehicle. At this  
time, greater steering effort is required to  
operate the steering wheel, especially in  
sharp turns and at low speeds.  
Supplemental air bag  
warning light  
When the ignition switch is placed in the ON  
or START position, the supplemental air  
bag warning light illuminates for about  
7 seconds and then turns off. This means  
the system is operational.  
WARNING  
If the supplemental air bag warning  
light is on, it could mean that the front  
air bag, side air bag, curtain air bag  
and/or pretensioner systems will not  
operate in an accident. To help avoid  
injury to yourself or others, have your  
vehicle checked as soon as possible. It is  
recommended that you visit a NISSAN  
dealer for this service.  
For additional information, refer to “Power  
steering” in the “Starting and driving” sec-  
tion of this manual.  
If any of the following conditions occur, the  
front air bag, side air bag, curtain air bag,  
and pretensioner seat belt systems need  
servicing:  
Seat belt warning light and  
chime  
The light and chime remind you to fasten  
your seat belts. The light illuminates when-  
ever the ignition switch is placed in the ON  
or START position and remains illuminated  
until the driver’s seat belt is fastened.  
INDICATOR LIGHTS  
The supplemental air bag warning light re-  
mains on after approximately 7 seconds.  
This vehicle has various indicator lights  
that may illuminate to indicate a system  
status. For additional information, refer to  
the specific light in this section.  
The supplemental air bag warning light  
flashes intermittently.  
Automatic Transmission  
position indicator light (A/T  
models only)  
The supplemental air bag warning light  
does not come on at all.  
The seat belt warning light may also illumi-  
nate if the front passenger’s seat belt is not  
fastened when the front passenger’s seat  
is occupied.  
It is recommended that you visit a NISSAN  
dealer for these services.  
When the ignition switch is in the ON posi-  
tion, this indicator light shows the shift le-  
ver position. For additional information, re-  
fer to “Driving the vehicle” in the “Starting  
and driving” section of this manual.  
Unless checked and repaired, the supple-  
mental restraint system (air bag system)  
and/or the pretensioner(s) may not func-  
tion properly. For additional information, re-  
fer to “Supplemental Restraint System  
(SRS)” in the “Safety—Seats, seat belts and  
supplemental restraint system” section of  
this manual.  
For additional information, refer to “Seat  
belts” in the “Safety—Seats, seat belts and  
supplemental restraint system” section of  
this manual.  
Instruments and controls 2-11  
test. For additional information, refer to  
“Readiness for Inspection/Maintenance  
(I/M) test” in the “Technical and consumer  
information” section of this manual.  
CRUISE indicator light (if so  
equipped)  
The light comes on when the CRUISE  
ON/OFF switch is pushed. The light goes  
out when the CRUISE ON/OFF switch is  
pushed again. When the CRUISE indicator  
light comes on, the cruise control system is  
operational.  
High beam indicator light  
(blue)  
This blue light comes on when the head-  
light high beams are on and goes out when  
the low beams are selected.  
Operation  
The MIL will come on in one of two ways:  
The high beam indicator light also comes  
on when the passing signal is activated.  
MIL on steady — An emission control  
system malfunction has been de-  
tected. Check the fuel-filler cap if the  
LOOSE FUEL CAP warning appears in  
the trip computer. If the fuel-filler cap is  
loose or missing, tighten or install the  
cap and continue to drive the vehicle.  
Malfunction Indicator Light  
(MIL)  
If this indicator light comes on steady or  
blinks while the engine is running, it may  
indicate a potential emission control mal-  
function.  
For additional information, refer to “Cruise  
control” in the “Starting and driving” section  
of this manual.  
Front fog light indicator  
light (if so equipped)  
The front fog light indicator light illumi-  
nates when the front fog lights are on. For  
additional information, refer to “Front fog  
lights” in this section.  
The  
few driving trips. If the  
light should turn off after a  
light does  
The  
may also come on steady if the  
not turn off after a few driving trips, have  
the vehicle inspected. It is recom-  
mended that you visit a NISSAN dealer  
for this service. You do not need to have  
your vehicle towed to the dealer.  
fuel-filler cap is loose or missing or if the  
vehicle runs out of fuel. Check to make sure  
the fuel-filler cap is installed and closed  
tightly and that the vehicle has at least 3 gal  
(11.4 L) of fuel in the fuel tank.  
Front passenger air bag  
status light  
The front passenger air bag status  
will be lit and the passenger front  
air bag will be off depending on how the  
front passenger seat is being used.  
For additional information, refer to “Front  
passenger air bag and status light” in the  
“Safety — Seats, seat belts and supplemen-  
tal restraint system” section of this manual.  
MIL blinking — An engine misfire has  
been detected which may damage the  
emission control system. To reduce or  
avoid emission control system dam-  
age:  
After a few driving trips, the  
light  
light  
should turn off if no other potential emis-  
sion control system malfunction exists.  
If this indicator light comes on steady for  
20 seconds and then blinks for 10 seconds  
when the engine is not running, it indicates  
that the vehicle is not ready for an emission  
control system inspection/maintenance  
– Do not drive at speeds above  
45 mph (72 km/h).  
2-12 Instruments and controls  
– Avoid hard acceleration or decelera-  
tion.  
For additional information, refer to “Driving  
the vehicle” in the “Starting and driving” sec-  
tion of this manual.  
The  
indicator light also comes on  
when you place the ignition switch in the  
ON position. The light will turn off after ap-  
proximately 2 seconds if the system is op-  
erational. If the light does not come on  
have the system checked. It is recom-  
mended that you visit a NISSAN dealer for  
this service.  
– Avoid steep uphill grades.  
Security indicator light  
– If possible, reduce the amount of  
cargo being hauled or towed.  
This light blinks when the ignition switch is  
placed in the OFF, LOCK or ACC position.  
The MIL may stop blinking and come on  
steady. Have the vehicle inspected. It is rec-  
ommended that you visit a NISSAN dealer  
for this service. You do not need to have  
your vehicle towed to the dealer.  
The blinking security indicator light indi-  
cates that the security systems equipped  
on the vehicle are operational.  
Turn signal/hazard  
indicator lights  
The appropriate light flashes when the turn  
signal switch is activated.  
For additional information, refer to “Security  
systems” in this section.  
CAUTION  
Both lights flash when the hazard switch is  
turned on.  
Slip indicator light  
Continued vehicle operation without  
having the emission control system  
checked and repaired as necessary  
could lead to poor driveability, reduced  
fuel economy, and possible damage to  
the emission control system.  
This indicator light will blink when the Ve-  
hicle Dynamic Control (VDC) system is op-  
erating, thus alerting the driver to the fact  
that the road surface is slippery and the  
vehicle is nearing its traction limits.  
Vehicle Dynamic Control  
(VDC) OFF indicator light  
This indicator light comes on when the  
VDC OFF switch is pushed to off. This indi-  
cates the VDC system has been turned off.  
Overdrive OFF indicator  
light (A/T models only)  
This light comes on when the overdrive  
function is OFF.  
You may feel or hear the system working;  
this is normal.  
Push the VDC OFF switch again or restart  
the engine and the system will operate  
normally. For additional information, refer  
to “Vehicle Dynamic Control (VDC) system”  
in the “Starting and driving” section of this  
manual.  
The light will blink for a few seconds after  
the VDC system stops limiting wheel spin.  
The automatic transmission overdrive  
function is controlled by the overdrive  
switch.  
Instruments and controls 2-13  

Related Topics

Popular Owner Manuals