Get Lighting and visibility Guide for Peugeot 108 4 Door 2014-2022

Lighting and visibility

Main lighting

Lighting control stalk

Main lighting

Travelling abroad

If planning to use your vehicle in a country

that drives on the other side of the road,

the headlamp dipped beams must be

adjusted to avoid dazzling oncoming

drivers.

The various front and rear lamps of the vehicle

are designed to adapt the driver's visibility

progressively according to the climatic

conditions:

Contact a PEUGEOT dealer or a qualified

workshop.

-

sidelamps, to be seen,

dipped beam headlamps to see without

dazzling other drivers,

Turn the ring to align the desired symbol with

the marking.

-

main beam headlamps to see clearly when

the road is clear.

Headlamps off/Daytime running

lamps.

Without AUTO lighting

With AUTO lighting

Sidelamps only.

Additional lighting

Other lamps are provided to meet the

requirements of particular driving conditions:

-

Dipped or main beam headlamps.

a rear foglamp,

front foglamps,

daytime running lamps to be more visible

during the day.

Automatic illumination of headlamps.

In some weather conditions (e.g. low

temperature or humidity), the presence

of misting on the internal surface of the

glass of the headlamps and rear lamps is

normal; it disappears after the lamps have

been on for a few minutes.

Dipping the headlamps

46

Lighting and visibility

With the dipped beams on, push the control

forwards to switch on the main beams. Pull the

control towards you to return to dipped beams.

Front foglamps and rear

foglamp

In good or rainy weather, both day and

night, using the front foglamps and the

rear foglamp is prohibited. In these

situations, the power of their beams may

dazzle other drivers. They should only be

used in fog or falling snow.

In these weather conditions, it is your

responsibility to switch on the foglamps

and dipped headlamps manually as the

sunshine sensor may detect sufficient

light.

In the lighting off and sidelamps modes, the

driver can switch on the main beam headlamps

temporarily ("headlamp flash"), for as long as

the stalk is kept pulled.

Turn and release the ring:

F forwards once to switch on the rear

foglamp,

F forwards a second time to switch on the

front foglamps,

F backwards once to switch off the front

foglamps,

F backwards a second time to switch off the

rear foglamp.

If the lighting is switched off automatically

(version with AUTO lighting) or the dipped

beams are switched off manually, the foglamps

and sidelamps remain on.

Displays

Illumination of the corresponding indicator

lamp in the instrument panel confirms that the

lighting selected is switched on.

Do not forget to turn off the front foglamps

and the rear foglamp as soon as they are

no longer necessary.

4

Selection ring for the

foglamps

F Turn the ring backwards and release it to

turn off all the lamps.

Switching off the lamps when the

ignition is switched off

When switching off the ignition, all of the

lamps turn off immediately, except for

dipped beam if guide-me-home lighting is

activated.

Switching on the lighting after the

ignition is switched off

To reactivate the lighting control, rotate

the ring to the 0 position – lamps off, then

to the desired position.

On opening the driver's door a temporary

audible signal warns the driver that the

lighting is on.

The foglamps operate when the dipped or main

beams are on.

47

Lighting and visibility

-

you put the lighting control in another

position,

you switch on the ignition.

Automatic headlamp

illumination

Manual guide-me-home

lighting

(Depending on version)

Direction indicators

When a low level of ambient light is detected by

a light sensor, the sidelamps and dipped beam

headlamps are switched on automatically,

without any action on the part of the driver.

As soon as the level of light becomes sufficient

again, the lamps are switched off automatically.

The sensor is located at the bottom of the

windscreen.

Temporarily keeps the dipped beam

headlamps on after the vehicle's ignition has

been switched off, making exit easier for the

occupants when the light is poor.

F Left: lower the lighting stalk passing the

point of resistance.

F Right: raise the lighting stalk passing the

point of resistance.

Switching on

F Turn the ring to the "AUTO" position.

F Set the lighting control stalk to the "Lights

off" or "Auto" position.

F With the ignition off, flash the headlamps

using the lighting stalk.

Switching off

Three flashes

F Turn the ring to another position.

The headlamps come on for a duration of about

30 seconds.

F Press briefly upwards or downwards,

without going beyond the point of

resistance; the direction indicators will flash

3 times.

In fog or snow, the sunshine sensor may

detect sufficient light. The lamps will not

come on automatically.

Switching off

Do not cover the light sensor, the

associated functions would no longer be

controlled.

The manual guide-me-home lighting stops

immediately if:

-

you "flash the headlamps" again,

48

Lighting and visibility

Single wipe.

Headlamp adjustment

Wiper control stalk

In wintry conditions, remove snow, ice or

frost present on the windscreen, around

the wiper arms and blades and the

windscreen seal, before operating the

wipers.

For a single wipe of the windscreen, raise the

control then release it.

Off.

Intermittent wipe.

Do not operate the wipers on a dry

windscreen. Under extremely hot or cold

conditions, ensure that the wiper blades

are not stuck to the windscreen before

operating the wipers.

Normal wiping (moderate rain).

Fast wiping (heavy rain).

To avoid causing a nuisance to other road

users, the height of the headlamp beams

should be adjusted according to the load in the

vehicle.

4

0.

Driver only.

0.5. Driver + front passenger.

1.5. 4 people.

Front screenwash

3.

4 people + maximum authorised load.

Manual controls

3.5. Driver + maximum authorised load.

The initial setting is position 0.

Pull the wiper control stalk towards you. The

screenwash and then the wipers operate for

a preset time.

Front wipers

Wiping speed control stalk: raise or lower the

stalk to the desired position.

49

Lighting and visibility

Rear wiper

Changing a wiper blade

Removing the front wiper blade

F Raise the wiper arm.

F Take off the blade by sliding it to the

outside.

Reﬁtting the front wiper blade

Turn the ring to this position for

F Put the new wiper blade in place and

secure it.

continuous wiping.

F Carefully lower the wiper arm.

Pushing the ring forwards triggers screen

washing during the wiping (hold it for

continuous washing).

To maintain the effectiveness of the wiper

blades, it is advisable to:

Rear screenwash

-

handle them with care,

clean them regularly using soapy

water,

-

avoid using them to retain cardboard

on the windscreen,

replace them at the first signs of wear.

With the rear wiper off, turn the control towards

you to release a jet of screenwash (keep it

turned if you wish the jet to continue).

Do not use the front or rear screenwash

control when the screenwash reservoir is

empty. You risk damaging the pump.

50

Lighting and visibility for Your Peugeot 108 4 Door 2014-2022

Related Topics

Popular Owner Manuals

Latest Owner Manuals