2021-2025 Peugeot 308 4 Door Lighting and visibility -> Peugeot Matrix LED Technology 2.0 User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Lighting and visibility -> Peugeot Matrix LED Technology 2.0 for Your Peugeot 308 4 Door 2021-2025

Lighting and visibility  
The state of the system is stored when the  
ignition is switched off.  
Pause  
4
If the situation requires a change of headlamp  
beam, the driver can take over at any time.  
► Switch the headlamps manually between  
dipped and main beam to pause the function.  
If the "AUTO" and "Dipped beam" indicator  
lamps were on, the system changes to main  
beam.  
When the system detects thick fog, it  
temporarily deactivates the function.  
Operation  
If the ambient light level is very low and traffic  
conditions permit:  
– The main beam headlamps  
come on automatically. These  
indicator lamps light up on the instrument panel.  
If the ambient light level is sufficient and/or the  
traffic conditions do not allow the main beam  
headlamps to be lit:  
If the "AUTO" and "Main beam" indicator lamps  
were on, the system changes to dipped beam.  
► To reactivate the function, once again switch  
the headlamps manually between dipped and  
main beam.  
Malfunction  
– The dipped beam headlamps  
If a malfunction occurs with the system or  
the camera, this warning lamp lights up  
on the instrument panel, accompanied by an  
audible signal and a message.  
remain lit. These indicator lamps  
light up on the instrument panel.  
The function is deactivated if the foglamps  
are switched on or if the system detects poor  
visibility conditions (e.g. fog, heavy rain,  
snowfall).  
This system is a driving aid.  
The driver remains responsible for  
the vehicle's lighting, its correct use in the  
prevailing light, visibility and traffic conditions,  
and for compliance with driving and vehicle  
regulations.  
Have it checked by a PEUGEOT dealer or a  
qualified workshop.  
When the foglamps are switched off or when the  
visibility conditions become favourable again, the  
function is automatically reactivated.  
This indicator lamp goes out when the  
function is deactivated.  
If the function is selected but the display  
on the instrument panel and the alerts are  
not available, the indicator lamp comes on in  
grey.  
Peugeot Matrix LED  
Technology 2.0  
The system becomes operational when  
the vehicle exceeds 16 mph (25 km/h).  
When the speed falls below 9 mph (15 km/h),  
the function is no longer operational.  
For more information, refer to the  
General recommendations for  
automatic lighting systems.  
Activation/Deactivation  
Available only on versions equipped with Full  
LED headlamps with Matrix Beam function.  
It is configured in the Settings > Vehicle  
touch screen application.  
71  
Lighting and visibility  
This system automatically adapts the main  
beam according to the driving conditions, so that  
optimum illumination is maintained for the driver,  
without causing a nuisance to other road users.  
signalled by the indicator lamp going off on  
the instrument panel.  
Followed vehicle  
Travelling abroad  
Vehicles equipped with the Peugeot  
Matrix LED Technology 2.0 function:  
If planning to use your vehicle in a country  
that drives on the other side of the road,  
deactivate the function to avoid dazzling  
oncoming drivers.  
The driver remains responsible for the  
vehicle's lighting, its correct use in the  
prevailing light, visibility and traffic conditions,  
and for compliance with driving and vehicle  
regulations.  
When approaching a vehicle from behind, only  
those lamp segments directed at the followed  
vehicle go off, thereby creating a "tunnel" so as  
not to dazzle its driver.  
The system is active from 25 mph  
(40 km/h) and deactivates below 12 mph  
(20 km/h).  
Operation  
Using a camera, the system detects the driving  
conditions (brightness, lights from oncoming or  
followed vehicles, road turns) and adapts the  
beams of the main headlamps accordingly.  
The modules that make up the main beams  
switch on and off gradually, segment by  
segment, depending on the driving conditions  
detected.  
Oncoming vehicle  
Activation/Deactivation  
► Place the ring of the lighting control stalk in  
the “AUTO” position.  
This indicator lamp comes on in the  
instrument panel.  
It is configured in the Settings > Vehicle  
touch screen application.  
Nominal main beam lighting is restored as soon  
as the vehicle is no longer detected by the  
system.  
The state of the system is stored when the  
ignition is switched off.  
When deactivated, the lighting system changes  
to "Automatic illumination of lamps" mode.  
When an oncoming vehicle approaches, only  
those lamp segments directed at this vehicle  
go off, thereby creating a "tunnel" during the  
duration of the approach.  
It is recommended that you deactivate  
the function in foggy or snowy conditions  
or in case of heavy mist.  
The function temporarily is deactivated when  
the system detects thick fog or when the  
foglamps are switched on manually. This is  
Entering an illuminated area  
At the entrance to an illuminated area (for  
example, a town), the lamp segments are  
gradually switched off from the outside to the  
72  
Lighting and visibility  
inside of the vehicle to switch to the dipped  
beams.  
With AUTO wiping  
Wiper control stalk  
4
Before operating the wipers in wintry  
conditions, clear any snow, ice or frost  
from the windscreen and around the wiper  
arms and blades.  
Exiting an illuminated area  
The lamp segments gradually light up from the  
inside to the outside of the vehicle to restore the  
main beams.  
Windscreen wipers  
Do not operate the wipers on a dry  
windscreen. In extremely hot or cold  
weather, check that the wiper blades are not  
stuck to the windscreen before operating the  
wipers.  
Pause  
► To select the wiping speed: raise or lower the  
stalk to the desired position.  
If the situation requires a change of headlamp  
beam, the driver can take over at any time.  
► Switch the dipped/main beam headlamps  
manually to pause the function.  
Fast wiping (heavy rain)  
Normal wiping (moderate rain)  
Intermittent wipers  
The lighting system changes to "Automatic  
illumination of lamps" mode.  
► To reactivate the function, manually switch  
the dipped/main beam headlamps again.  
After using an automatic car wash, you  
may temporarily notice abnormal noises  
and poorer wiping performance. You do not  
need to replace the wiper blades.  
or  
Malfunction  
Automatic wipers  
If a malfunction occurs with the adaptive  
headlamp lighting or the camera, this  
warning lamp is displayed on the instrument  
panel, accompanied by an audible signal and a  
message.  
With intermittent wipers  
Switching off  
Manual  
Have it checked by a PEUGEOT dealer or a  
qualified workshop.  
After the ignition has been switched off,  
the wipers may move slightly at the foot  
of the windscreen.  
Do not cover the rain/sunshine sensor  
located at the top centre of the  
windscreen behind the interior rear view  
mirror; the associated functions would no  
longer be controlled.  
73  

Related Topics

Popular Owner Manuals