2012-2017 Peugeot 4007 4 Door PRACTICAL INFORMATION -> Changing a wheel User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

PRACTICAL INFORMATION -> Changing a wheel for Your Peugeot 4007 4 Door 2012-2017

PRACTICAL INFORMATION  
List of tools  
Other accessories  
CHANGING A WHEEL  
Access to the tools  
4. Removable towing eye.  
Refer to the "Towing" paragraph.  
Wheel with trim  
The tools are stored in the storage com-  
partment in the boot right-hand trim.  
To gain access to them:  
) open the boot,  
) turn button A to the left,  
) remove the cover B,  
) remove the fixing band C and take  
out the tool bag D containing the  
tools,  
1. Wheelbrace.  
Used to remove the wheel trim and  
the wheel fixing bolts.  
2. Jack.  
9
Used to raise the vehicle.  
3. Handle.  
Used to extend the jack.  
) take the jack E in your hand and re-  
move it from its fixing position.  
When removing the wheel, remove  
the trim first using the handle 3, pulling  
at the notch.  
When refitting the wheel, refit the trim  
starting by placing its notch F (indicated  
on the back of the trim) opposite the  
valve G and press on its outer edge  
with the palm of your hand.  
When storing, take care to se-  
cure the tool bag D firmly using  
the fixing band C.  
When changing a wheel, ensure  
that the four wheels are of identi-  
cal specification and brand.  
 
PRACTICAL INFORMATION  
Access to the spare wheel in  
the 7 seat configuration  
Putting the wheel back in place  
) Put the wheel back in place in its  
carrier.  
) Remove the plastic cover A using  
the handle 3.  
) Lift the carrier C and reposition the  
hook D.  
) Open the lower tailgate (refer to the  
The "space-saver" spare wheel is in-  
stalled on the outside, under the boot,  
supported by a metal carrier.  
"Access" section).  
To gain access to the tools, refer to the  
"Access to the tools" paragraph.  
Fixing the "space-saver"  
spare wheel  
If your vehicle is fitted with al-  
loy wheels, it is normal to notice  
that the washers do not come  
into contact with the "space-  
saver" spare wheel when tight-  
ening the bolts on fitting. The  
wheel is retained by the conical  
contact of each bolt.  
9
) Unscrew the spare wheel carrier re-  
taining bolt B using the wheelbrace 1.  
) Close the lower tailgate (refer to the  
"Access" section).  
) Tighten the spare wheel carrier  
retaining bolt B fully using the  
wheelbrace 1.  
) Refit the plastic cover A, close the  
lower tailgate and store the tools.  
) Lift the carrier C to detach the hook D  
then allow it to lower.  
Removing the wheel  
) Open the tailgate and the lower tail-  
gate (refer to the "Access" section).  
) Take out the handle 3 (refer to the  
"Access to the tools" paragraph).  
 
PRACTICAL INFORMATION  
Access to the spare wheel in  
the 5 seat configuration  
Putting the wheel back in place  
) Put the wheel back in place in its  
) Remove the plastic cover A using  
the handle 3.  
carrier.  
) Pass the hook C into the chain.  
) Open the lower tailgate (refer to the  
"Access" section).  
The pressed steel spare wheel is installed  
on the outside, under the boot, supported  
by a winch and a plastic carrier.  
To gain access to the tools, refer to the  
"Access to the tools" paragraph.  
Fixing the pressed steel  
spare wheel  
9
If your vehicle is fitted with alloy  
wheels, it is normal to notice that  
the washers do not come into  
contact with the pressed steel  
spare wheel when tightening the  
bolts on fitting. The wheel is re-  
tained by the conical contact of  
each bolt.  
) Unscrew the retaining bolt B fully  
using the wheelbrace 1, to unwind  
the winch cable.  
) Close the lower tailgate (refer to the  
"Access" section).  
) Detach the hook C from the chain.  
Unwind the winch cable fully to make  
unhooking of the chain easier.  
) Tighten the winch retaining bolt B  
fully using the wheelbrace 1.  
) Refit the plastic cover A, close the  
Removing the wheel  
) Open the tailgate and the lower tail-  
gate (refer to the "Access" section).  
) Take out the handle 3 (refer to the  
"Access to the tools" paragraph).  
lower tailgate and store the tools.  
 
PRACTICAL INFORMATION  
List of operations  
Removing a wheel  
) If your vehicle is equipped with secu-  
rity wheel bolts (equipment available  
as an accessory) fit the security sock-  
et 5 on the wheelbrace 1 to slacken  
the security bolt.  
) Slacken the other bolts using the  
wheelbrace 1 only.  
) Place the jack 2 in contact with one  
of the two front A or rear B locations  
provided on the underbody, which-  
ever is closest to the wheel to be  
changed.  
) Extend the jack 2 until its base plate  
is in contact with the ground. Ensure  
that the centreline of the jack base  
plate is directly below the location A  
or B used.  
Parking the vehicle  
Immobilise the vehicle where it  
does not block traffic: if possible,  
park the vehicle on level, stable  
and non-slippery ground.  
9
Apply the parking brake, switch  
off the ignition and engage first  
gear to lock the wheels.  
If necessary, place a chock under  
the wheel diagonally opposite the  
wheel to be changed.  
) Raise the vehicle until there is suffi-  
cient space between the wheel and  
the ground to admit the spare (not  
punctured) wheel easily.  
) Remove the bolts and store them in  
a clean place.  
) Remove the wheel.  
Never go underneath a vehicle  
raised using a jack; use a stand.  
 
PRACTICAL INFORMATION  
List of operations  
Fitting a wheel  
) Put the wheel in place on the hub.  
) Screw in the bolts fully by hand.  
) Pre-tighten the security bolt us-  
ing the wheelbrace 1 fitted with the  
security socket 5 (if your vehicle is  
equipped with security wheel bolts).  
) Tighten the security bolt using the  
wheelbrace 1 fitted with the security  
socket 5 (if your vehicle is equipped  
with security wheel bolts).  
) Tighten the other bolts using the  
wheelbrace 1 only.  
) Store the tools (refer to the para-  
) Pre-tighten the other bolts using the  
wheelbrace 1 only.  
graph "Access to the tools").  
9
After changing a wheel  
When using the "space-saver"  
spare wheel, do not exceed a  
speed of 50 mph (80 km/h).  
Have the tightening of the bolts  
and the pressure of the spare  
wheel checked by a PEUGEOT  
dealer or a qualified workshop  
without delay.  
Have the punctured wheel re-  
paired and replace it on the ve-  
hicle as soon as possible.  
Fitting snow tyres  
If you equip your vehicle with  
snow tyres fitted on steel wheel  
rims, special bolts available  
from your PEUGEOT dealer or  
a qualified workshop must be  
used.  
) Lower the vehicle fully.  
) Fold the jack 2 and detach it.  
 

Related Topics

PRACTICAL INFORMATION
Changing a bulb Changing a fuse Battery Changing a wiper blade Towing Towing a trailer Fitting roof bars Accessories

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot