Get Fittings -> Boot fittings 7 seat version Guide for Peugeot 5008 SUV First Generation (2009-2016)

Fittings

Boot ﬁttings (7 seat version)

1. Load space cover

2. Hooks

3. 12 V accessory socket (120 W)

4. Torch

5. Concertina boards

6. Stowing rings on the floor

7. Cup holder

5

8. Armrests

9. Storage compartments or audio

amplifier

10. 3^rdrow seat belt buckles

113

Fittings

Roller load space cover

To install the load space cover:

F

position one of the ends of the roller in its

support,

To remove the load space cover:

To store the load space cover, roller uppermost

and flap facing towards the inside of the

vehicle:

F

insert the second end in its support,

pivot the ends of the roller downwards to

secure it,

reel out the load space cover to the boot

pillars,

F

remove the load space cover guides from

the rails on the boot pillars,

F

reel in the load space cover in its roller,

F

place the right-hand end in its housing,

slide the left-hand end into the guide then

into its housing,

F

insert the load space screen guides in the

rails on the boot pillars.

If you use the 3^rdrow seats (7 seat

version), it is essential to store the roller

in its housing.

F

pivot the ends of the roller upwards to

release it,

remove the roller from its support.

F

secure the assembly by pivoting the ends

downwards.

The roller has two rings for fixing the

luggage retaining net depending on its

location.

114

Fittings

High load retaining

net*

Hooked onto the special upper and lower

fixings, this permits use of the entire loading

volume up to the roof:

-

behind the front seats (row 1) when the

rear seats are folded.

-

behind the rear seats (row 2).

When positioning the net, check that

the strap loops are visible from the

boot; this will make slackening or

tightening easier.

5

To use it in row 1:

To use it in row 2:

F

fold the rear seats,

F

roll up or remove the load space screen,

open the covers of the upper fixings 1,

unroll the high load retaining net,

position one of the ends of the net's metal

bar in the corresponding upper fixing 1,

then do the same with the other end,

slacken the straps fully,

open the covers of the upper fixings 2,

unroll the high load retaining net,

position one of the ends of the net's metal

bar in the corresponding upper fixing 2,

then do the same with the other end,

fix the snap hook of each of the straps in

the corresponding stowing ring 4,

tighten the straps,

F

fix the snap hook of each of the straps

on the corresponding Top Tether ring 3

(located on the back of the folded rear side

seats),

F

check that the net is hooked and tightened

correctly.

F

tighten the straps,

check that the net is hooked and tightened

correctly.

* If your vehicle is equipped with this.

115

Fittings

There are 4 possible positions:

Luggage retaining net

Hooked onto the stowing rings on the floor and/

or on the load space cover roller, the luggage

retaining net available as an accessory enables

you to secure your luggage.

-

flat at the bottom of the boot,

-

vertical at the back of the rear seats,

-

horizontal, level with the load space cover,

-

flat at the bottom of the boot and vertical at

the back of the rear seats.

116

Fittings

Hooks

12 V accessory socket

Storage box

(5 seat version)

5

The hooks can be used to hold shopping bags.

F

To connect a 12 V accessory (max power:

120 W), remove the cap and connect an

appropriate adaptor.

F

Raise the concertina board to gain access

to the storage box.

Depending on the configuration, this has areas

for storing:

Turn the key to the ignition on position.

-

a box of spare bulbs,

a first aid kit,

a tyre repair kit,

two warning triangles,

...

117

Fittings

Torch

Rear side blinds

This is a removable lamp, fitted in the boot wall,

which can be used to illuminate the boot or as

a torch.

Fitted on the rear windows, these protect your

young children from the sun.

F

Pull the blind by the central tab.

2^ndrow

For the boot lighting function, refer to

the "Visibility" section.

Use

F

Extract the torch from its location pulling

the side of the torch A.

Press the switch, located on the back, to

switch the torch on or off.

Unfold the support, located on the back, to

set down and raise the torch; for example,

when changing a wheel.

Operation

Storing

This torch operates with NiMH type

rechargeable batteries.

It has a battery life of approximately 45 minutes

and charges while you are driving.

F

Put the torch back in place in its location

starting with the narrow part B.

If you have forgotten to switch off the torch,

this switches it off automatically.

Observe the polarities when fitting the

batteries.

Never replace the rechargeable batteries

with normal single-use batteries.

3^rdrow (7 seat version)

It the torch is not engaged correctly, it

may not charge and may not come on

when the boot is opened.

F

Position the blind attachment on the hook.

118

Fittings -> Boot fittings 7 seat version for Your Peugeot 5008 SUV First Generation (2009-2016)

Related Topics

Fittings