2009-2016 Peugeot 5008 SUV Practical information User Manual

MY CAR USER MANUAL

Practical information for Your Peugeot 5008 SUV First Generation (2009-2016)

Practical information  
Tool kit  
This is a set of tools provided with your vehicle. The content depends on your vehicle's equipment (temporary puncture repair kit or  
spare wheel).  
Access to the tools  
The tools 6 to 8 are stowed in a box, in the  
middle of the spare wheel, placed underneath  
the vehicle.  
The tools 1, 2, 4a to 5 and 9 are stowed under  
the concertina boards and in the boot inner  
trim.  
To gain access to them:  
F
F
F
open the boot,  
raise the concertina boards.  
remove the spare wheel placed under the  
vehicle.  
See the "Changing a wheel" section.  
If your vehicle is equipped with  
10  
temporary puncture repair kit, contact  
a PEUGEOT dealer or a qualified  
workshop for the part numbers of the  
tools needed: jack and wheelbrace.  
215  
Practical information  
List of tools  
For versions with spare  
wheel:  
All of these tools are specific to your vehicle.  
Do not use them for other purposes.  
1. Two chocks to immobilise the vehicle  
(depending on equipment).  
5. Wheelbrace.  
For removing the wheel trim and the  
wheel fixing bolts.  
6. Jack with integral handle.  
For raising the vehicle.  
2. Removable towing eye.  
See the "Towing the vehicle" section.  
3. Socket for the security bolts (located in the  
glove box) (depending on equipment).  
For adapting the wheelbrace to the special  
security bolts.  
7. Wheel bolt cover removal tool (depending  
on equipment).  
For removing the wheel bolt head finishers  
on alloy wheels.  
8. Centre guide (depending on equipment).  
For refitting an alloy wheel to the hub.  
9. Wheelbrace extension.  
For unwinding/winding up the spare wheel  
carrier drive.  
For versions without spare  
wheel:  
4a. Temporary puncture repair kit (5-seat).  
4b. Temporary puncture repair kit (7-seat).  
Comprises a 12 V compressor and a  
sealant cartridge for the temporary repair  
of a puncture and can be used for adjusting  
tyre pressure.  
See the "Temporary puncture repair kit"  
section.  
216  
Practical information  
Temporary puncture repair kit (5-seat version)*  
Complete system consisting of a compressor and a sealant cartridge which permits temporary repair of a tyre so that you can drive  
to the nearest garage.  
It is designed to repair most punctures which could affect the tyre, located on the tyre tread or shoulder.  
Access to the kit  
The vehicle's electric system allows the  
connection of a compressor for long  
enough to inflate a tyre after a puncture  
repair or for inflating a small inflatable  
accessory.  
The kit is located in the boot under the  
concertina board.  
The towing eye 2 is located in the boot interior  
trim, on the left-hand side.  
10  
* Depending on country of sale.  
217  
Practical information  
Description of the kit  
The speed limit sticker I must be affixed  
to the vehicle's steering wheel to remind  
you that a wheel is in temporary use.  
Do not exceed a speed of 50 mph  
(80 km/h) when driving with a tyre  
repaired using this type of kit.  
A. "Sealant" or "Air" position selector.  
B. On "I" / off "O" switch.  
C. Deflation button.  
D. Pressure gauge (in bar and p.s.i.).  
E. Compartment housing:  
F. Sealant cartridge.  
G. White pipe with cap for repair.  
H. Black pipe for inflation.  
I. Speed limit sticker.  
-
-
a cable with adaptor for 12 V socket,  
various inflation adaptors for  
accessories, such as balls, bicycle  
tyres...  
218  
Practical information  
Repair procedure  
1. Sealing  
F
F
Switch off the ignition.  
Turn the selector A to the  
"sealant" position.  
Check that the switch B is in  
position "O".  
F
F
F
Uncoil the white pipe G fully.  
F
F
Connect the compressor's electric plug to  
the vehicle's 12 V socket.  
Start the vehicle and leave the engine  
running.  
Unscrew the cap from the white pipe.  
Connect the white pipe to the valve of the  
tyre to be repaired.  
F
10  
Take care, this product is harmful (e.g.  
ethylene-glycol, colophony...) if swallowed  
and causes irritation to the eyes.  
Keep this product out of the reach of  
children.  
Avoid removing any foreign bodies  
which have penetrated into the tyre.  
Do not start the compressor before  
connecting the white pipe to the tyre  
valve: the sealant product would be  
expelled through the pipe.  
219  
Practical information  
F
Switch on the compressor by moving  
the switch B to position "I" until the tyre  
pressure reaches 2.0 bars.  
The sealant is injected into the tyre under  
pressure; do not disconnect the pipe from  
the valve during this operation (risk of  
splashing).  
F
F
F
Remove the kit and screw the cap back on  
the white pipe.  
Take care to avoid staining your vehicle  
with traces of fluid. Keep the kit to hand.  
Drive immediately for approximately three  
miles (five kilometres), at reduced speed  
(between 15 and 35 mph (20 and  
60 km/h)), to plug the puncture.  
Stop to check the repair and the tyre  
pressure using the kit.  
Tyre under-inflation detection  
If after around 5 to 7 minutes the  
pressure is not attained, this indicates  
that the tyre is not repairable; contact  
a PEUGEOT dealer or a qualified  
workshop for assistance.  
If the vehicle is fitted with tyre under-  
inflation detection, the under-inflation  
warning lamp will remain on after the  
wheel has been repaired until the  
system is reinitialised by a PEUGEOT  
dealer or a qualified workshop.  
220  
Practical information  
2. Inflation  
F
Turn the selector A to the "air"  
position.  
Uncoil the black pipe H fully.  
Connect the black pipe to the  
valve of the wheel.  
F
F
Connect the compressor's electric plug to  
the vehicle's 12 V socket.  
Start the vehicle again and leave the  
engine running.  
F
Adjust the pressure using the compressor  
(to inflate: switch B in position "I"; to  
deflate: switch B in position "O" and press  
button C), in accordance with the vehicle's  
tyre pressure label (located on the left  
hand door aperture).  
F
F
A loss of pressure indicates that the  
puncture has not been fully plugged;  
contact a PEUGEOT dealer or qualified  
workshop for assistance.  
As soon as possible, go to a PEUGEOT  
dealer or a qualified workshop.  
You must inform the technician that you  
have used this kit. After inspection, the  
technician will advise you on whether  
the tyre can be repaired or if it must be  
replaced.  
F
F
Remove and stow the kit.  
10  
Drive at reduced speed (50 mph [80 km/h]  
max) limiting the distance travelled to  
approximately 120 miles (200 km).  
221  
Practical information  
Removing the cartridge  
Checking tyre pressures /  
inflating accessories  
You can also use the compressor, without  
injecting any product, to:  
-
-
check or adjust the pressure of your  
tyres,  
inflate other accessories (balls, bicycle  
tyres...).  
F
F
F
F
Stow the black pipe.  
Detach the angled base from the white pipe.  
Support the compressor vertically.  
Unscrew the cartridge from the bottom.  
F
Connect the compressor's electrical  
connector to the vehicle's 12 V socket.  
Start the vehicle and let the engine run.  
Adjust the pressure using the compressor  
(to inflate: switch B in position "I"; to  
deflate: switch B in position "O" and press  
button C), according to the vehicle's tyre  
pressure label or the accessory's pressure  
label.  
F
F
Beware of discharges of fluid.  
The expiry date of the fluid is indicated  
on the cartridge.  
The sealant cartridge is designed for  
single use; even if only partly used, it  
must be replaced.  
After use, do not discard the cartridge  
into the environment, take it to an  
authorised waste disposal site or a  
PEUGEOT dealer.  
Do not forget to obtain a new sealant  
cartridge, available from PEUGEOT  
dealers or from a qualified workshop.  
F
Turn the selector A to the "Air"  
position.  
F
Remove the kit then stow it.  
F
F
Uncoil the black pipe H fully.  
Connect the black pipe to the  
valve of the wheel or accessory.  
If necessary, fit one of the adaptors  
supplied with the kit first.  
222  
Practical information  
Temporary puncture repair kit (7 seat version)*  
Complete system consisting of a compressor  
Using the kit  
and a bottle of sealant which permits  
temporary repair of the tyre so that you can  
drive to the nearest garage.  
F
F
Switch off the ignition.  
F
F
F
Check that the switch A is tilted to  
position "0".  
Connect the pipe of the bottle 1 to the valve  
of the tyre to be repaired.  
Unwind the pipe of the compressor 2 fully,  
then connect it to the bottle.  
Tick the wheel to be repaired on the  
speed limitation sticker enclosed then  
affix the sticker to the vehicle's steering  
wheel to remind you that a wheel is in  
temporary use.  
The kit is located in the boot, under the left  
hand seat in the 3rd row.  
This kit is available from a PEUGEOT  
dealer or a qualified workshop.  
F
Clip the bottle 1 on the compressor 2.  
It is designed to repair holes of a  
maximum diameter of 6 mm, only where  
located on the tyre tread or shoulder.  
Avoid removing any foreign bodies  
which have penetrated the tyre.  
10  
* According to country of sale.  
223  
Practical information  
F
F
Connect the compressor's electric plug to  
the vehicle's 12 V socket.  
Start the vehicle and leave the engine  
running.  
F
Switch on the compressor by tilting the  
switch A to position "1" until the tyre  
pressure reaches 2.0 bars.  
F
F
F
Remove the compressor and store the  
bottle in the plastic bag, supplied in the kit,  
to avoid staining your vehicle with traces  
of fluid.  
Drive immediately for approximately  
two miles (three kilometres), at reduced  
speed (between 10 and 35 mph [20 and  
60 km/h]), to plug the puncture.  
Stop to check the repair and the pressure.  
224  
Practical information  
F
Connect the compressor pipe directly to  
the valve of the repaired wheel.  
F
F
Connect the compressor's electric plug to  
the vehicle's 12 V socket again.  
Start the vehicle again and leave the  
engine running.  
F
Adjust the pressure using the compressor  
(to inflate: switch A in position "1"; to  
deflate: switch A in position "0" and  
press button B), in accordance with the  
vehicle's tyre pressure label (located on  
the door aperture on the driver's side), then  
remember to check that the leak is plugged  
correctly (no further loss of pressure after  
several miles [kilometres]).  
F
F
Remove the compressor, then store the  
whole kit.  
Drive at reduced speed (50 mph [80 km/h]  
max) for no more than approximately  
125 miles (200 km).  
Visit a PEUGEOT dealer or a qualified  
workshop as soon as possible to have the  
tyre repaired or replaced by a technician.  
If this pressure has not been reached  
after approximately five to ten minutes,  
the tyre cannot be repaired; contact a  
PEUGEOT or a qualified workshop to  
have your vehicle repaired.  
10  
F
225  
Practical information  
Changing a wheel  
See the "Tool kit" section.  
Take care, the bottle of fluid contains  
ethylene-glycol. This product is harmful  
if swallowed and causes irritation to the  
eyes. Keep it out of reach of children.  
The expiry date of the fluid is indicated  
on the base of the bottle.  
Access to the spare wheel*  
The bottle is designed for a single use;  
even if only partly used, it must be  
replaced.  
After use, do not discard the bottle into  
the environment, take it to a PEUGEOT  
dealer or an authorised waste  
disposal site.  
Do not forget to obtain a new bottle  
of sealant product, available from  
a PEUGEOT dealer or a qualified  
workshop.  
The spare wheel is supported by a cable-driven  
carrier underneath the vehicle.  
Taking out the wheel  
F
F
Raise the concertina board.  
Raise the cut-out in the boot carpet for  
access to the spare wheel carrier drive nut.  
If the vehicle is fitted with tyre under-  
inflation detection, the tyre under-  
inflation warning lamp will remain on  
after the wheel has been repaired  
until the system is reinitialised by  
a PEUGEOT dealer or a qualified  
workshop.  
* Depending on country of sale.  
226  
Practical information  
F
Turn this drive nut fully clockwise, using  
the wheelbrace 5 and the extension 9, to  
unwind the carrier cable.  
F
F
Detach the wheel/box assembly from the  
rear of the vehicle.  
Remove the hook with its connection plate  
to release the wheel/box assembly, as  
shown in the illustration.  
F
F
Pull out the wheel to gain access to  
the box.  
Slide the box cover to the centre and  
remove it to gain access to the other tools.  
10  
227  
Practical information  
F
F
Raise the wheel/box assembly underneath  
the vehicle by turning the carrier drive nut  
anticlockwise using the wheelbrace 5 and  
the extension 9.  
Tighten fully and check that the wheel is  
horizontally flush against the floor.  
Putting the wheel back in place  
F
F
F
Store the tools used in the box and close  
the cover.  
Position the box on the ground and centre  
the spare wheel on it.  
Pass the hook with its connection plate into  
the wheel then the box, as illustrated.  
228  
Practical information  
Removing a wheel  
Parking the vehicle  
Immobilise the vehicle where it does not  
block traffic: the ground must be level,  
stable and non-slippery ground.  
Apply the parking brake unless it has  
been programmed to automatic mode,  
switch off the ignition and block the  
wheels:  
-
by engaging 1st gear, with a manual  
gearbox,  
-
by placing the gear selector at  
position R with an electronic  
gearbox,  
F
F
F
Remove the bolt cover from each of the  
bolts using the tool 7 (depending on  
equipment).  
Fit the security socket 3 on the  
wheelbrace 5 to slacken the security bolt  
(if your vehicle has them).  
F
Position the foot the jack 6 on the ground  
and ensure that it is directly below one  
of the front A or rear B jacking points  
provided on the underbody, whichever is  
closest to the wheel to be changed.  
-
by placing the gear selector at  
position P with an automatic  
gearbox.  
Check that the braking warning lamp  
and the P warning lamp on the parking  
brake control come on.  
If necessary, place a chock under the  
wheel diagonally opposite the wheel to  
be changed.  
The occupants must get out of the  
vehicle and wait where they are safe.  
Never go underneath a vehicle raised  
using a jack; use an axle stand.  
Slacken the other bolts using the  
wheelbrace 5 only.  
Wheel with wheel trim  
When removing the wheel, first  
remove the wheel trim using the  
wheelbrace 5 by pulling at the valve  
cut-out.  
When refitting the wheel, refit the  
wheel trim by placing its cut-out at the  
valve, and press round its edge with the  
palm of your hand.  
10  
229  
Practical information  
Ensure that the jack is stable. If the  
ground is slippery or loose, the jack  
might slip and drop.  
Position the jack only at the locations A  
or B.  
Ensure that the head of the jack is  
positioned centrally on the jacking  
location. Otherwise there is a risk of  
damage to the vehicle and the jack  
may drop.  
F
F
Extend the jack until its head comes into  
contact with A or B; the contact surface A  
or B must be correctly engaged with the  
middle of the head of the jack.  
Raise the vehicle until there is sufficient  
space between the wheel and the ground  
to admit the spare (not punctured) wheel  
easily.  
F
F
Remove the bolts and store them in a clean  
place.  
Remove the wheel.  
Following a puncture  
The punctured wheel cannot be stowed  
under the vehicle. It must be stowed in the  
boot. Use a cover to protect the inside of  
the boot.  
When driving with the "space-saver" type  
spare wheel fitted, do not exceed 50 mph  
(80 km/h).  
Have the tightening of the bolts and the  
pressure of the spare wheel checked by a  
PEUGEOT dealer or a qualified workshop  
without delay.  
Have the punctured wheel repaired and  
replace it on the vehicle as soon as possible.  
Tyre under-inflation detection  
The space-saver type or steel spare  
wheel does not have a sensor.  
The punctured wheel must be repaired  
by a PEUGEOT dealer or a qualified  
workshop.  
230  
Practical information  
Fitting a wheel  
F
Put the wheel in place on the hub using the  
centre guide 8.  
F
F
Lower the vehicle fully.  
Fold the jack 6 and detach it.  
F
Using the wheelbrace 5 fitted with the  
security socket 3, tighten the security bolt  
(if your vehicle has them).  
Tighten the other bolts using the  
wheelbrace 5 only.  
Refit the bolt covers to each of the bolts  
(according to equipment).  
F
F
Screw in the bolts by hand to the stop.  
Using the wheelbrace 5 fitted with the  
security socket 3, pre-tighten the security  
bolt (if your vehicle has them).  
Pre-tighten the other bolts using the  
wheelbrace 5 only.  
F
F
F
F
Fitting the "space-saver"  
spare wheel  
Store the tools in the box.  
If your vehicle is fitted with alloy wheels,  
when tightening the bolts on fitting it  
is normal to notice that the washers  
do not come into contact with the  
"space-saver" spare wheel. The wheel  
is secured by the conical contact of  
each bolt.  
10  
231  
Practical information  
Snow chains  
In wintry conditions, snow chains improve traction as well as the behaviour of the vehicle when  
braking.  
Advice on installation  
F
If you have to fit the chains during a  
journey, stop the vehicle on a flat surface  
on the side of the road.  
Use only the chains designed to be fitted to the  
The snow chains must be fitted only  
to the front wheels. They must never  
be fitted to "space-saver" type spare  
wheels.  
type of wheel fitted to your vehicle:  
F
Apply the parking brake and position any  
wheel chocks to prevent movement of your  
vehicle.  
F
F
Fit the chains following the instructions  
provided by the manufacturer.  
Move off gently and drive for a few  
moments, without exceeding 30 mph  
(50 km/h).  
Original tyre size  
Maximum link size.  
215/55 R16  
215/50 R17  
215/45 R18  
F
Stop your vehicle and check that the snow  
chains are correctly tightened.  
9 mm  
For more information on snow chains, contact a  
PEUGEOT dealer or a qualified workshop.  
Avoid driving with snow chains on roads  
that have been cleared of snow, to  
avoid damaging your vehicle's tyres and  
the road surface. If your vehicle is fitted  
with alloy wheels, check that no part of  
the chain or its fixings is in contact with  
the wheel rim.  
It is strongly recommended that before  
you leave, you practise fitting the snow  
chains on a level and dry surface.  
Take account of the legislation in force  
in your country on the use of snow  
chains and the maximum running speed  
authorised.  
232  
Practical information  
Changing a bulb  
Front lamps  
Model with xenon and directional  
headlamps  
The headlamps are fitted with  
polycarbonate glass with a protective  
coating:  
Model with halogen headlamps  
F
do not clean them using a dry  
or abrasive cloth, nor with a  
detergent or solvent product,  
use a sponge and soapy water or a  
pH neutral product,  
when using a high pressure washer  
on persistent marks, do not keep  
the lance directed towards the  
lamps or their edges for too long,  
so as not to damage their protective  
coating and seals.  
F
F
1. Direction indicators (light-emitting  
diodes - LEDs).  
2. Dipped / main beam directional  
headlamps (D1S).  
3. Daytime running lamps / sidelamps  
(light-emitting diodes - LEDs).  
4. Foglamps (PS24W).  
Changing a bulb should only be done  
after the headlamp has been switched  
off for several minutes (risk of serious  
burns).  
1. Direction indicators  
(light-emitting diodes - LEDs).  
2. Main beam headlamps (HB3).  
3. Dipped beam headlamps (H7).  
4. Daytime running lamps/sidelamps  
(light-emitting diodes - LEDs).  
5. Foglamps (PS24W).  
F
Do not touch the bulb directly with  
your fingers, use a lint-free cloth.  
It is imperative to use only anti-  
ultraviolet (UV) type bulbs to avoid  
damaging the headlamp.  
Always replace a failed bulb with a  
new bulb with the same type and  
specification.  
10  
Risk of electrocution  
Xenon bulbs (D1S) must be replaced  
by a PEUGEOT dealer or a qualified  
workshop.  
233  
Practical information  
Changing direction indicators  
and daytime running lamps /  
sidelamps  
Changing dipped beam headlamp bulbs  
(models with halogen headlamps)  
Changing main beam headlamp bulbs  
(halogen model)  
For the replacement of these LED (light-  
emitting diode) lamps, contact a PEUGEOT  
dealer or a qualified workshop.  
F
Remove the protective plastic cover by  
pulling the tab.  
Disconnect the bulb connector.  
Extract the bulb by pulling and change it.  
F
F
Remove the protective plastic cover by  
pulling the tab.  
F
F
Without disconnecting the connector, turn  
the body of the bulb a quarter of a turn to  
the left to disengage the assembly.  
Disconnect the connector to release  
the bulb.  
To refit, carry out these operations in reverse  
order.  
F
To refit, carry out these operations in reverse  
order.  
234  
Practical information  
Changing integrated direction  
indicator side repeaters  
Changing foglamp  
bulbs  
Changing dipped beam and  
main beam headlamp bulbs  
(models with xenon headlamps)  
D1S xenon bulbs must be changed  
by a PEUGEOT dealer or a qualified  
workshop as there is a risk of  
electrocution.  
It is recommended that all D1S bulbs  
are changed at the same time if one of  
them fails.  
Contact a PEUGEOT dealer or a qualified  
workshop.  
F
Insert a screwdriver towards the centre of  
the repeater between the repeater and the  
base of the mirror.  
F
F
Tilt the screwdriver to extract the repeater  
and remove it.  
Disconnect the repeater connector.  
To refit, carry out these operations in reverse  
order.  
Contact a PEUGEOT dealer or a qualified  
workshop to obtain a new repeater.  
10  
You can also contact a PEUGEOT  
dealer or a qualified workshop to have  
these lamps changed.  
235  
Practical information  
Changing brake lamp and  
direction indicator bulbs  
Rear lamps  
F
F
Remove the two lamp unit fixing nuts.  
Pull the lamp rearwards (a positioning lug  
retains the lamp).  
F
Press the four tabs and remove the bulb  
holder.  
1. Direction indicators  
(PY21W-21W).  
2. Brake lamps  
(P21W-21W).  
3. Sidelamps  
(LEDs).  
F
Disconnect the lamp connector.  
4. Reversing lamp  
(P21W).  
5. Foglamp  
(P21W).  
236  
Practical information  
Changing sidelamps (LEDs)  
Changing foglamp or reversing  
lamp bulbs  
For the replacement of this type of LED lamp,  
contact a PEUGEOT dealer or a qualified  
workshop.  
F
Turn the bulb a quarter of a turn and  
change it.  
F
F
Reach under the bumper.  
Turn the bulb a quarter of a turn and  
change it.  
To refit, carry out these operations in reverse  
order.  
10  
237  
Practical information  
Changing the third brake lamp bulb  
(5W5)  
Changing the number plate lamp  
bulbs (W5W)  
F
Open the boot and remove the upper  
tailgate seal.  
F
Press the pairs of clips A then B then C to  
detach the bulb holders.  
F
Insert a thin screwdriver into one of the  
outer holes of the lens.  
F
F
Remove the centre tailgate trim.  
Unscrew the two nuts using a 10mm  
spanner.  
F
F
F
Push it outwards to unclip.  
Remove the lens.  
Pull the bulb out and change it.  
F
Press the threaded pins while supporting  
the lamp from the outside.  
F
F
Close the tailgate.  
Disconnect the lamp connector then the  
screenwash pipe to remove the lens.  
238  
Practical information  
Changing a fuse  
Procedure for replacing a faulty fuse with a new fuse to rectify a failure of the corresponding  
function.  
The replacement of a fuse not  
mentioned in the tables below may  
cause a serious malfunction on your  
vehicle.  
Contact a PEUGEOT dealer or a  
qualified workshop.  
Access to the tools  
Changing a fuse  
Before changing a fuse, the cause of the failure  
must be identified and rectified.  
F
Identify the failed fuse by checking the  
condition of its filament.  
Installing electrical  
accessories  
Your vehicle's electrical system is  
designed to operate with standard or  
optional equipment.  
Before installing other electrical  
equipment or accessories on your  
vehicle, contact a PEUGEOT dealer or  
a qualified workshop.  
The extraction tweezer is fitted to the back of  
the dashboard fusebox cover.  
To gain access to it:  
Good  
Failed  
F
F
Remove the cover completely.  
Remove the tweezer.  
PEUGEOT will not accept responsibility  
for the cost incurred in repairing your  
vehicle or for rectifying malfunctions  
resulting from the installation of  
accessories not supplied and not  
recommended by PEUGEOT and  
not installed in accordance with its  
instructions, in particular when the  
combined consumption of all of the  
additional equipment connected  
exceeds 10 milliamperes.  
F
F
F
Use the special tweezer to extract the fuse  
from its housing.  
Always replace the faulty fuse with a fuse  
of the same rating.  
Check that the number marked on the  
fusebox, the rating marked on the fuse and  
the following tables all agree.  
10  
239  
Practical information  
Dashboard fuses  
The fusebox is placed in the lower dashboard.  
Fuse tables  
Fuse  
N°  
Rating  
(A)  
Functions  
F1  
F2  
F3  
15  
-
Rear wiper.  
Not used.  
5
Airbag control unit.  
Electrochrome rear view mirror, air conditioning, switching and  
protection unit, rear multimedia.  
F4  
10  
F5  
F6  
30  
30  
Front one-touch electric windows.  
Rear one-touch electric windows.  
Front and rear courtesy lamps, map reading lamps, rear  
reading lamps, sun visor lighting, glove box lighting, centre  
armrest lighting, boot 12 V relay control.  
F7  
5
240  
Practical information  
Access to the fuses  
Fuse  
N°  
Rating  
(A)  
Functions  
F
Refer to the paragraph "Access to the  
tools".  
Audio equipment, audio/telephone, CD changer, multifunction  
scren, tyre under-inflation detection, alarm siren, alarm control  
unit, telematic unit.  
F8  
20  
F9  
30  
15  
15  
Front 12 V socket, cigarette lighter, rear 12 V socket.  
Steering mounted controls.  
F10  
F11  
Low current ignition switch.  
Trailer presence, rain / sunshine sensor, supply for fuses F32,  
F34, F35.  
F12  
15  
F13  
F14  
F15  
F17  
5
Engine fusebox, airbag control unit.  
15  
30  
40  
Instrument panel, instrument panel screen, supply for fuse F33.  
Locking and deadlocking.  
Heated rear screen, supply for fuse F30.  
10  
241  
Practical information  
Fuse  
N°  
Rating  
(A)  
Functions  
F30  
F31  
F32  
F33  
F34  
F35  
5
Heated door mirrors.  
30  
5
Boot 12 V socket.  
Electronic gearbox gear lever.  
10  
5
Head-up display, Bluetooth system, air conditioning.  
Seat belt warning lamp display.  
10  
Parking sensors, Hi-Fi amplifier authorisation.  
Trailer fusebox control unit, driver's door control  
pad.  
F36  
10  
F37  
F38  
F39  
20  
30  
20  
Hi-Fi amplifier.  
Driver's electric seat.  
Panoramic sunroof blind.  
242  
Practical information  
Fuse table  
Engine compartment  
fuses  
Fuse  
N°  
Rating  
(A)  
Functions  
The fusebox is placed in the engine  
compartment near the battery.  
F2  
F3  
F4  
15  
10  
10  
Horn.  
Front / rear wash-wipe.  
Daytime running lamps.  
Purge canister, turbine discharge and Turbo pressure  
regulation electrovalves (1.6 litre THP), oil vapour heater  
(1.6 litre THP), diesel heater (1.6 litre HDi).  
F5  
15  
Diagnostic socket, directional headlamps, particle  
emission filter pump (Diesel), Distance alert, mirror  
adjustment control.  
F6  
F7  
10  
10  
Access to the fuses  
F
F
Unclip the cover.  
Change the fuse (see corresponding  
paragraph).  
Power steering control unit, automatic gearbox, directional  
headlamps height adjustment motor.  
F
When you have finished, close the cover  
carefully to ensure correct sealing of the  
fusebox.  
F8  
F9  
20  
10  
40  
Starter motor control.  
Clutch and brake pedal switches.  
Air conditioning fan.  
F11  
10  
243  
Practical information  
Fuse  
N°  
Rating  
(A)  
Functions  
F12  
F14  
F15  
F16  
F17  
F18  
30  
30  
10  
10  
15  
15  
Windscreen wipers slow / fast speed.  
Air pump.  
Right-hand main beam headlamp.  
Left-hand main beam headlamp.  
Left-hand dipped headlamp.  
Right-hand dipped headlamp.  
244  
Practical information  
Table of fuses above the battery  
Fuse  
N°  
Rating  
(A)  
Functions  
Dual function brake switch.  
F2  
F3  
F4  
F6  
5
5
Battery charge unit.  
25  
15  
ABS/DSC electrovalves.  
Electronic / automatic gearbox.  
10  
245  
Practical information  
12 V battery  
Procedure for starting the engine using another  
battery or charging a discharged battery.  
Access to the battery  
The presence of this label, in particular with the  
Stop & Start system, indicates the use of a  
12 V lead-acid battery with special technology  
and specification; the involvement of a  
PEUGEOT dealer or a qualified workshop is  
essential when replacing or disconnecting the  
battery.  
Disconnecting the (+) cable  
F
Raise the locking tab D fully to release the  
cable terminal clamp E.  
The battery is located under the bonnet.  
To gain access to it:  
F
open the bonnet using the interior release  
lever, then the exterior safety catch,  
secure the bonnet stay,  
Reconnecting the (+) cable  
F
F
F
Position the open clamp E of the cable on  
the positive post (+) of the battery.  
Press vertically on the clamp E to position  
it correctly on the battery.  
F
F
remove the plastic cover on the (+) terminal,  
After refitting the battery, the Stop & Start system  
will only be active after a continuous period of  
immobilisation of the vehicle, a period which  
depends on the climatic conditions and the state of  
charge of the battery (up to about 8 hours).  
Lock the clamp by spreading the  
positioning lug and then lowering the tab D.  
Do not apply excessive force on the  
tab as locking will not be possible if the  
clamp is not positioned correctly; start  
the procedure again.  
With Stop & Start, the battery does not have to  
be disconnected for charging.  
246  
Practical information  
Starting using another  
battery  
When your vehicle's battery is discharged, the  
engine can be started using a slave battery  
(external or on another vehicle) and jump lead  
cables.  
F
F
Remove the plastic cover from the (+)  
terminal, if your vehicle has one.  
Connect the red cable to the positive  
terminal (+) of the flat battery A, then to the  
positive terminal (+) of the slave battery B.  
Connect one end of the green or black  
cable to the negative terminal (-) of the  
slave battery B (or earth point on the other  
vehicle).  
First check that the slave battery has a  
nominal voltage of 12 V and a capacity  
at least equal to that of the discharged  
battery.  
F
F
F
Connect the other end of the green or black  
cable to the earth point C on the broken  
down vehicle (or on the engine mounting).  
Start the engine of the vehicle with the  
good battery and leave it running for a  
few minutes.  
F
Operate the starter on the broken down  
vehicle and let the engine run  
Do not try to start the engine by  
connecting a battery charger.  
Do not disconnect the (+) terminal when  
the engine is running.  
If the engine does not start straight away, 10  
switch off the ignition and wait a few  
moments before trying again.  
F
F
Wait until the engine returns to idle then  
disconnect the jump lead cables in the  
reverse order.  
Refit the plastic cover to the (+) terminal,  
if your vehicle has one.  
247  
Practical information  
Before disconnecting the battery  
Charging the battery using  
a battery charger  
Protect your eyes and face before  
handling the battery.  
Wait 2 minutes after switching off the ignition  
before disconnecting the battery.  
Close the windows and the doors before  
disconnecting the battery.  
All operations on the battery must be  
carried out in a well ventilated area and  
away from naked flames and sources  
of sparks, so as to avoid the risk of  
explosion or fire.  
Do not try to charge a frozen battery;  
the battery must first be thawed out to  
avoid the risk of explosion. If the battery  
has been frozen, before charging have  
it checked by a PEUGEOT dealer or a  
qualified workshop who will check that  
the internal components have not been  
damaged and the casing is not cracked,  
which could cause a leak of toxic and  
corrosive acid.  
Do not reverse the polarity and use only  
a 12 V charger.  
Do not disconnect the terminals while  
the engine is running.  
Do not charge the batteries without  
disconnecting the terminals first.  
Wash your hands afterwards.  
F
Disconnect the battery from the vehicle.  
Follow the instructions for use provided by  
the manufacturer of the charger.  
Connect the battery starting with the  
negative terminal (-).  
Check that the terminals and connectors  
are clean. If they are covered with sulphate  
(whitish or greenish deposit), remove them  
and clean them.  
F
F
F
Following reconnection of the  
battery  
Following reconnection of the battery, switch on  
the ignition and wait 1 minute before starting to  
permit initialisation of the electronic systems.  
However, if problems remain following this  
operation, contact a PEUGEOT dealer or a  
qualified workshop.  
Referring to the corresponding section, you  
must yourself reinitialise (depending on  
version):  
The batteries contain harmful substances  
such as sulphuric acid and lead. They  
must be disposed of in accordance  
with regulations and must not, in any  
circumstances, be discarded with  
household waste.  
Take used remote control batteries and  
vehicle batteries to a special collection point.  
-
-
-
the remote control key,  
the electric blind(s),  
...  
It is advisable to disconnect the battery  
if the vehicle is to be left unused for  
more than one month.  
Do not push the vehicle to start the  
engine if you have an electronic or  
automatic gearbox.  
Some functions are not available if the  
battery is not sufficiently charged.  
248  
Practical information  
Load reduction mode Energy economy mode  
System which manages the use of certain  
functions according to the level of charge  
remaining in the battery.  
When the vehicle is being driven, the load  
reduction function temporarily deactivates  
certain functions, such as the air conditioning,  
the heated rear screen...  
System which manages the duration of use of certain functions to conserve a sufficient level of  
charge in the battery.  
After the engine has stopped, you can still use functions such as the audio and telematics  
system, windscreen wipers, dipped beam headlamps, courtesy lamps, etc. for a maximum  
combined duration of thirty minutes.  
This period may be greatly reduced if the battery is not fully charged.  
The deactivated functions are reactivated  
automatically as soon as conditions permit.  
Switching to economy mode Exiting economy mode  
Once this time has elapsed, a message  
appears in the screen indicating that the  
vehicle has switched to economy mode and the  
active functions are put on standby.  
These functions are reactivated automatically  
next time the vehicle is driven.  
To restore the use of these functions  
immediately, start the engine and let it run for at  
least 5 minutes.  
Let the engine run for the duration  
specified to ensure that the battery  
charge is sufficient.  
Do not repeatedly and continuously  
restart the engine in order to charge the  
battery.  
A flat battery prevents the engine  
from starting (refer to the "Battery"  
paragraph).  
If the telephone is being used at this  
time:  
-
it will be maintained for 5 minutes  
with the hands-free kit of your  
PEUGEOT Connect Sound or  
PEUGEOT Connect Navigation,  
it will still be possible to finish the  
call with the PEUGEOT Connect  
Media.  
-
10  
249  
Practical information  
Changing a wiper blade  
Towing the  
vehicle  
Procedure for having your vehicle towed or for  
towing another vehicle using the removable  
towing eye provided in the tool kit.  
Access to the tools  
Before removing a front  
wiper blade  
Fitting  
F
Put the corresponding new wiper blade in  
place and clip it.  
F
Within one minute after switching off  
the ignition, operate the wiper stalk to  
position the wiper blades vertically on the  
windscreen.  
F
Fold down the wiper arm carefully.  
The towing eye is installed under the left-hand  
concertina board, in the boot interior trim.  
For access to it:  
Removing  
After fitting a front wiper  
blade  
F
Raise the corresponding wiper arm.  
F
Unclip the wiper blade and remove it.  
F
Switch on the ignition.  
F
F
F
open the boot,  
raise the concertina board,  
remove the towing eye from the holder.  
F
Operate the wiper stalk again to park the  
wiper blades.  
250  
Practical information  
General recommendations  
Observe the legislation in force in your  
country.  
Ensure that the weight of the towing  
vehicle is higher than that of the towed  
vehicle.  
Towing your vehicle  
Towing another  
vehicle  
The driver must remain at the wheel of  
the towed vehicle and must have a valid  
driving licence.  
When towing a vehicle with all four  
wheels on the ground, always use an  
approved towing bar; rope and straps  
are prohibited.  
When towing a vehicle with the engine  
off, there is no longer any power  
assistance for braking or steering.  
F
On the front bumper, unclip the cover by  
pressing at the bottom.  
Screw the towing eye in fully.  
Install the towing bar.  
Switch on the hazard warning lamps on the  
towed vehicle.  
F
On the rear bumper, unclip the cover by  
pressing at the bottom.  
Screw the towing eye in fully.  
Install the towing bar.  
Switch on the hazard warning lamps on the  
towed vehicle.  
In the following cases, you must always  
call on a professional recovery service:  
F
F
F
F
F
F
-
vehicle broken down on a motorway  
or fast road,  
-
4 wheel drive vehicle,  
-
when it is not possible to put the  
gearbox into neutral, unlock the  
steering, or release the parking  
brake,  
Put the gear lever into neutral  
(position N for an electronic or  
automatic gearbox).  
Failure to follow this instruction could  
lead to damage to certain components  
(brakes, transmission, ...) and the  
absence of braking assistance on  
restarting the engine.  
10  
-
-
towing with only two wheels on the  
ground,  
where there is no approved towing  
bar available...  
251  
Practical information  
Towbar with quickly detachable towball  
No tools are required to install or remove the towball on this genuine towbar system.  
Fitting  
F
F
Ensure that the towball is fully engaged.  
The two pins must be in contact with  
the cut-outs in the carrier and the  
trigger B must have returned to the  
"locked" position.  
F
Before fitting the towball, check that the  
points of contact, indicated by the arrows,  
are clean.  
F
Below the rear bumper, unclip and remove  
the protective cover on the carrier.  
Install and clip in place the protective  
cover, by rotating it to the left.  
Use a soft clean cloth.  
F
F
On the towball, press and hold control A.  
Release the locking mechanism by  
pressing the trigger B.  
F
Put the end of the towball into the carrier,  
located below the bumper, as far as it will go.  
F
F
Connect the trailer plug to the 13-way  
socket provided, located next to the carrier.  
Make the trailer safe by attaching its safety  
cable to the eye provided for this purpose,  
located on the carrier.  
252  
Practical information  
Removing  
If the towball is not locked in place, the  
trailer could separate. There is a risk of  
an accident.  
Always lock the towball in the way  
described.  
Observe the legislation in force in the  
country in which you are driving.  
Remove the towball when it is not  
being used.  
F
Press the trigger B and remove the towball  
by pulling it towards you.  
Before setting off, check that the trailer  
lighting and signalling works correctly.  
Maximum authorised nose weight:  
70 kg.  
F
Unclip and remove the protective cover, by  
turning it to the right.  
Refer to the "Technical data" section for  
the maximum weights and towed loads  
for your vehicle.  
Carrying system (box or bicycle carrier).  
You must not exceed the maximum  
nose weight on the towbar: if this weight  
is exceeded, the device could detach  
from the vehicle and cause a serious  
accident.  
F
Clip the protective cover in place on the  
carrier located below the bumper.  
10  
When the towball is installed, it may  
interfere with the complete opening of  
the lower tailgate.  
Take care to avoid the tailgate coming  
into contact with the towball.  
F
F
On the towball, press and hold control A.  
Release the locking mechanism by  
pressing the trigger B.  
253  
Practical information  
Towing a trailer  
Driving advice  
We recommend the use of genuine  
PEUGEOT towbars and their harnesses  
that have been tested and approved  
from the design stage of your vehicle,  
and that the fitting of the towbar is  
entrusted to a PEUGEOT dealer or a  
qualified workshop.  
Distribution of loads  
F
Distribute the load in the trailer so that the  
heaviest items are as close as possible to  
the axle and the nose weight approaches  
the maximum permitted without  
exceeding it.  
If the towbar is not fitted by a  
PEUGEOT dealer, it is imperative that it  
is fitted in accordance with the vehicle  
manufacturer's instructions.  
Air density decreases with altitude, thus  
reducing engine performance. Above  
1 000 metres, the maximum towed load must  
be reduced by 10 % for every 1 000 metres of  
altitude.  
Your vehicle is primarily designed for  
transporting people and luggage, but it may  
also be used for towing a trailer.  
Driving with a trailer places greater  
demands on the towing vehicle and the  
driver must take particular care.  
Refer to the "Technical data" section for  
details of the weights and towed loads  
which apply to your vehicle.  
If the trailer starts to sway, you risk  
losing control. The trailer could  
overturn. There is a risk of an accident.  
Do not try to correct the trailer's  
movement by accelerating. Reduce  
your speed and do not counter-steer.  
Brake if necessary.  
254  
Practical information  
Side wind  
Braking  
F
Take into account the increased sensitivity  
to side wind.  
Towing a trailer increases the braking distance.  
To avoid overheating of the brakes on a long  
mountain type of descent, the use of engine  
braking is recommended.  
Cooling  
Towing a trailer on a slope increases the  
temperature of the coolant.  
As the fan is electrically controlled, its cooling  
capacity is not dependent on the engine speed.  
Tyres  
F
Check the tyre pressures of the towing  
vehicle and of the trailer, observing the  
recommended pressures.  
F
To lower the engine speed, reduce your  
speed.  
The maximum towed load on a long incline  
depends on the gradient and the ambient  
temperature.  
In all cases, keep a check on the coolant  
temperature.  
Lighting  
F
Check the electrical lighting and signalling  
on the trailer.  
The rear parking sensors will be  
deactivated automatically if a genuine  
PEUGEOT towbar is used.  
F
If the warning lamp and the STOP  
warning lamp come on, stop the  
vehicle and switch off the engine  
as soon as possible.  
10  
255  
Practical information  
Fitting roof bars  
Maximum authorised weight on the roof  
bars, for a loading height not exceeding  
40 cm (with the exception of bicycle  
carriers): 65 kg.  
If the height exceeds 40 cm, adapt the  
speed of the vehicle to the profile of the  
road to avoid damaging the roof bars  
and the fixings on the roof.  
Be sure to refer to national legislation in  
order to comply with the regulations for  
transporting objects that are longer than  
the vehicle.  
If your vehicle is fitted with roof  
finishers, do not use them for carrying  
loads.  
When fitting transverse roof bars, use the four  
quick-fit fixings provided for this purpose:  
F
F
lift the concealing flaps,  
open the fixing covers on each bar using  
the key,  
F
F
F
put each fixing in place and lock them on  
the roof one by one,  
ensure that roof bars are correctly fitted (by  
shaking them),  
close the fixing covers on each bar using  
the key.  
256  
Practical information  
Very cold climate screen  
Removable protective screen which prevents the accumulation of snow at the radiator cooling fan.  
Before fitting or removing the screen, ensure that the engine is off and the cooling fan has stopped. It is recommended that the screen be fitted and  
removed by a PEUGEOT dealer or a qualified workshop.  
Fitting  
Removal  
F
F
Offer up the screen, placing the lower clips  
F
F
Unclip the upper part of the screen, starting  
at the edges.  
Take the screen by the lower edges and  
detach it by pulling it towards you.  
Do not forget to remove the very cold  
climate screen:  
in contact with lower section of the lower  
grille, using the centre guide as an aid.  
Clip first the lower part, then the upper  
part, from the middle out towards the  
edges.  
-
when the ambient temperature  
exceeds 10° C,  
-
when towing,  
-
at speeds above 75 mph (120 km/h).  
10  
257  
Practical information  
Accessories  
A wide range of accessories and genuine parts is available from the PEUGEOT dealer network.  
These accessories and parts are all adapted to your vehicle and benefit from PEUGEOT's recommendation and warranty.  
"Comfort"  
"Style"  
"Protection"  
Mats*, boot liner, luggage net, style mud  
flaps**, seat covers, pet range, boot sill  
protector...  
Door deflectors, parking sensors, side window  
Alloy wheels, door sill trims, chrome-plated  
blinds, coat-hanger, insulated module...  
door handle shells, spoiler, gear lever knob...  
"Transport solutions"  
Roof bars, towbars, bicycle carrier on towbar,  
bicycle carrier on roof bars, ski carrier, rigid  
and flexible roof boxes...  
Trailer towbar, which must be fitted by a  
PEUGEOT dealer.  
"Safety and security"  
Anti-theft alarm, window etching, wheel  
security bolts, child seats and booster  
cushions, first aid kit, breathalyzer, warning  
triangle, high visibility vest, stolen vehicle  
tracking system, dog guard, winter equipment  
(snow chains, non-slip covers...)...  
*
To avoid any risk of jamming of the pedals:  
-
ensure that the mat is positioned and  
secured correctly,  
-
never fit one mat on top of another.  
** The configuration of the vehicle requires  
that it be fitted with mud flaps at the rear.  
258  
Practical information  
"Multimedia"  
Depending on the legislation in force in  
the country, certain safety equipment  
may be compulsory: high visibility  
safety vests, warning triangles,  
breathalyzers, spare bulbs, spare fuses,  
fire extinguisher, first aid kit, mud flaps  
at the rear of the vehicle.  
You can also obtain cleaning and  
maintenance products (exterior and  
interior), products for topping up  
(screenwash fluid...) and refills (sealant  
cartridge for the temporary puncture  
repair kit...) from PEUGEOT dealers.  
Portable satellite navigation systems, mapping  
updates, Bluetooth hands-free system, DVD  
player, USB Box, additional Bluetooth wireless  
headphones, Bluetooth audio headphones  
mains charger, multimedia support...  
The fitting of electrical equipment  
or accessories which are not  
recommended by PEUGEOT may result  
in a failure of your vehicle's electronic  
system and excessive electrical  
consumption.  
Contact a PEUGEOT dealer  
for information on the range of  
recommended equipment and  
accessories.  
Installation of radio  
communication  
transmitters  
Before installing any after-market radio  
communication transmitter, you can  
contact a PEUGEOT dealer for the  
specification of transmitters which can  
be fitted (frequency, maximum power,  
aerial position, specific installation  
requirements), in line with the Vehicle  
Electromagnetic Compatibility  
Directive (2004/104/EC).  
10  
259  
Technical data  
Petrol engines and gearboxes  
1.6 litre VTi  
120 hp  
1.6 litre THP  
150 / 156 / 163 hp  
1.6 litre e-THP  
165 hp  
Engine  
Manual  
(5-speed)  
Manual  
(6-speed)  
Automatic  
(6-speed)  
Automatic  
(6-speed)  
Gearbox  
Cubic capacity (cc)  
1 598  
77 x 85.8  
88  
1 598  
1 598  
77 x 85.8  
121  
Bore x stroke (mm)  
77 x 85.8  
Max power: EU standard (kW)*  
Max power engine speed (rpm)  
Max torque: EU standard (Nm)  
Max torque engine speed (rpm)  
Fuel  
110 / 115 / 120  
5 660  
6 000-6 050 / 6 000 / 6 000  
6 000  
160  
240  
1 400  
240  
4 250  
1 400  
Unleaded petrol  
yes  
Unleaded petrol  
yes  
Unleaded petrol  
yes  
Catalytic converter  
Engine oil capacity (in litres)  
(with filter replacement)  
4.25  
4.25  
4.25  
* The maximum power corresponds to the type approved value on a test bed, under the conditions defined in European legislation (directive 1999/99/CE).  
260  

Related Topics

Tool kit
Temporary puncture repair kit
Changing a wheel
Changing a fuse
12 V battery
Energy economy mode
Changing a wiper blade
Towing the vehicle
Towbar with quickly detachable towball
Towing a trailer
Fitting roof bars
Very cold climate screen
Accessories