Get Lighting and visibility -> Cornering lighting Guide for Peugeot 5008 SUV Second Generation (2017-2023)

Lighting and visibility

The system becomes operational when

the vehicle exceeds 16 mph (25 km/h).

When the speed falls below 9 mph (15 km/h),

the function is no longer operational.

Clean the windscreen regularly,

particularly the area in front of the

camera.

The internal surface of the windscreen can

also become misted around the camera.

In humid and cold weather, demist the

windscreen regularly.

Do not allow snow to accumulate on the

bonnet or roof of the vehicle as this could

obstruct the detection camera.

Pause

If the situation requires a change of headlamp

beam, the driver can take over at any time.

► A "headlamp ﬂash" pauses the function:

• if the "AUTO" and "Dipped beam" indicator

lamps were on, the system changes to main

beam,

Activation/Deactivation

It is set via the Driving / Vehicle touch

screen menu.

• if the "AUTO" and "Main beam" indicator

lamps were on, the system changes to

dipped beam.

To reactivate the system, ﬂash the headlamps

again.

The state of the system stays in the memory

when switching oﬀ the ignition.

Operation

If the ambient light level is suﬃcient and/or the

traﬃc conditions do not allow the main beam

headlamps to be lit:

– The dipped beam headlamps

remain lit. These indicator lamps

come on on the instrument panel.

If the ambient light level is very low and traﬃc

conditions permit:

Cornering lighting

The system may be disrupted or not work

correctly:

– When visibility conditions are poor

(snowfall, heavy rain, etc.).

– If the windscreen in front of the camera is

dirty, misted or obscured (for example, by a

sticker).

– If the vehicle is facing highly reﬂective

signs.

– The main beam headlamps

come on automatically. These

indicator lamps come on on the instrument

panel.

The function is deactivated if the fog lamps are

switched on or the system detects dense fog.

When the fog lamps are switched oﬀ or the

vehicle leaves the area of dense fog, the function

is automatically reactivated.

When the system detects thick fog, it

temporarily deactivates the function.

The system is not able to detect:

– Road users that do not have their own

lighting, such as pedestrians.

– Vehicles whose lighting is obscured (for

example, vehicles driving behind a safety

barrier on a motorway).

(Only on versions equipped with Full LED

technology headlamps)

This system makes use of the beam from a front

foglamp to illuminate the inside of a bend, when

the main or dipped beam headlamps are on and

the vehicle speed is below 25 mph (40 km/h)

(urban driving, winding road, junctions, parking

manoeuvres).

This indicator lamp goes out when the

function is deactivated.

– Vehicles at the top or bottom of a steep

slope, on winding roads, on crossroads.

Lighting and visibility

Fast wiping (heavy rain)

the wiper arms and blades and on the

windscreen seal, before operating the wipers.

Normal wiping (moderate rain)

Do not operate the wipers on a dry

windscreen. Under extremely hot or cold

conditions, ensure that the wiper blades are

not stuck to the windscreen before operating

the wipers.

Intermittent wiping (proportional to the

vehicle’s speed)

Oﬀ

Without/With cornering lighting

After switching oﬀ the ignition, a slight

movement of the windscreen wipers to

store them under the bonnet may occur.

Without AUTO wiping

Activation / Deactivation

It is set via the Driving / Vehicle touch

screen menu.

If the ignition has been switched oﬀ with

the windscreen wiper active, it is

necessary to operate the control stalk to

reactivate the wiping when the ignition is

switched on (unless the ignition is oﬀ for less

than 1 minute).

Switching on / oﬀ

This system starts:

– when the corresponding direction indicator is

switched on.

– from a certain angle of rotation of the steering

wheel.

It becomes inactive:

– below a certain angle of rotation of the

steering wheel.

– above 25 mph (40 km/h).

– when reverse gear is engaged.

Automatic wiping (proportional to the

rainfall).

Refer to the corresponding section.

With AUTO wiping

Windscreen wipers

Single wipe

► Pull the stalk brieﬂy towards you.

Wiper control stalk

In wintry conditions, remove snow, ice or

frost present on the windscreen, around

► To select the wiping speed: raise or lower the

stalk to the desired position.

Lighting and visibility

To avoid damaging the wiper blades, do

not operate the screenwash if the

screenwash reservoir is empty.

Only operate the screenwash if there is no

risk of the ﬂuid freezing on the windscreen

and hindering visibility. During the winter

period, use "very cold climate" rated products.

Never top up with water.

In the event of accumulation of snow or

hard frost or if a bicycle carrier is ﬁtted to

a towing device, deactivate the automatic rear

wiper via the vehicle conﬁguration menu.

Front screenwash

Rear screenwash

► Turn the ring all the way towards the

dashboard and hold.

The screenwash and the wiper operate for as

long as the ring remains turned.

A ﬁnal wiping cycle is performed when

screenwashing ends.

Rear wiper

► Pull the wiper control stalk towards you and

hold.

The screenwash and windscreen wipers operate

for as long as the control stalk is pulled.

Termination of the screenwash is followed by a

ﬁnal wiping cycle.

Special position of the

windscreen wipers

This maintenance position is used while cleaning

or replacing the wiper blades. It can also be

useful, in winter (ice, snow), to release the wiper

blades from the windscreen.

► Turn the ring to align the desired symbol with

the marking.

Oﬀ

The front screenwash jets are integrated

in the tips of each arm.

The screenwash ﬂuid is sprayed along the

length of the wiper blade. This improves

visibility and reduces the consumption of

screenwash ﬂuid.

In some cases, depending on the contents

or colour of the ﬂuid and on the exterior

brightness, the liquid spray may be hardly

noticeable.

Intermittent wipe

Wash-wipe

To maintain the eﬀectiveness of the ﬂat

wiper blades, it is advisable to:

– handle them with care.

– clean them regularly using soapy water.

– avoid using them to hold cardboard on the

windscreen.

Reverse gear

When reverse gear is engaged, the rear wiper

will come into operation automatically if the front

windscreen wipers are operating.

This function is set via the vehicle

conﬁguration menu.

– replace them at the ﬁrst signs of wear.

Lighting and visibility

Before removing a windscreen wiper blade

► Unclip the worn wiper blade closest to you

and remove it.

► Install the new wiper blade and clip it to the

arm.

Changing a wiper blade

Removing/reﬁtting at the front

► Repeat the procedure for the other wiper

blade.

► Starting with the wiper blade closest to you,

once again hold each arm by the rigid section,

then guide it carefully onto the windscreen.

Removing/reﬁtting at the rear

► Hold the arm by the rigid section and raise it

as far as possible.

► Clean the rear screen using screenwash

ﬂuid.

► Unclip the worn wiper blade and remove it.

► Install the new wiper blade and clip it to the

arm.

► Once again hold the arm by the rigid section,

then guide it carefully onto the rear screen.

► Operating the wiper control stalk within one

minute after switching oﬀ the ignition will place

the wiper blades in a vertical position.

► Proceed with the desired operation or replace

the wiper blades.

► Carry out these wiper blade replacement

operations from the driver's side.

► Starting with the wiper blade farthest from

you, hold each arm by the rigid section and raise

it as far as possible.

After reﬁtting a windscreen wiper blade

► To return the wiper blades to their initial

position, switch on the ignition and operate the

wiper control stalk.

Take care not to hold the arms at the jet

locations.

Do not touch the wiper blades. Risk of

irreparable deformation.

Do not release them while moving them. Risk

of damaging the windscreen!

Automatic windscreen

wipers

In AUTO mode, the windscreen wipers operate

automatically, without any action on the part of

the driver. If rain is detected, the wiping adapts to

the intensity of the rainfall automatically.

Detection of rainfall is by means of a rain/

sunshine sensor at the top centre of the

windscreen, behind the rear view mirror.

► Clean the windscreen using screenwash

ﬂuid.

Do not apply "Rain X" type water-

repellent products.

Lighting and visibility -> Cornering lighting for Your Peugeot 5008 SUV Second Generation (2017-2023)

Related Topics

Lighting and visibility