Get Instruments and controls -> Gearbox and steering wheel Guide for Peugeot Boxer Van First Generation (1994-2002)

Ventilation

ADDITIONAL HEATING SYSTEMS

Additional heating

This is passenger compartment heating,

additional to the standard equipment.

It can operate independently of the engine.

Additional heater or programmable

additional heating

This is an additional, programmable and

separate system which heats the Diesel

engine hot coolant loop to make starting

easier.

Supplementary heating

REAR HEATING AND/OR AIR

CONDITIONING

On the 2-3 seats version, this is located

under the seat on the driver's side with air

diffusion directed forwards.

If your vehicle is fitted with an

additional air conditioning unit,

located in the rear of the vehicle:

It improves the demisting and defrosting

performance and that of the heated seats, if

fitted to the vehicle.

On the 5-9 seats version, it is

located at the rear. Depending

on the model version, the air

the distribution duct located in

the roof and the individual diffusion vents

provide a perfect diffusion of cold air.

The passenger compartment heating is

brought up to temperature more rapidly.

diffusion is either direct from the

rear or comes from the rail located under

each of the two rows of seats.

The warm air diffused at the ﬂoor, from the

front air conditioning unit, is distributed at the

feet of the rear passengers of rows 2 and 3.

This system must be programmed to start up

before you enter the vehicle.

A warm air diffusion vent, located on the rear

left wheelarch, may complete the assembly

for the feet of the rear passengers of row 3.

Press this control to activate/

deactivate the heating. The LED

is on if the heating is activated.

When rapid demisting and

defrosting is required, switch off the control.

Ventilation

To deactivate the blower, place the control in

position 0.

However, a safety device will ventilate the

rear circuit automatically, even if the control

is in position 0, to prevent the formation of

condensation.

Activation/Deactivation

This control, located on the

control panel at the right-hand

end of the dashboard, enables

you to activate/deactivate the

operation of the rear controls from the

driver's seat.

Comfort value adjustment

Control positioned:

-

on the blue, produces cool

air,

The first press activates (LED on).

A second press deactivates (LED off).

-

on the red, produces heating

of the ambient air.

Air flow

The force of the blown air, via

the vents, varies from 1 to the

strongest 4.

To obtain a comfortable level of

ambient air, remember to adjust this control.

The OFF control on the "Mono-zone" central

control panel switches the function off.

3

Ventilation

Heating cycle indicator lamp

Display on

Displaying the programme

number selected

Time display button

Time setting buttons

Selection of the stored

programme

An integrated clock permits programming of

its start time. The passenger compartment

will be heated more quickly.

PROGRAMMABLE ADDITIONAL

HEATING

Button for immediate switching

on of the heating

If your vehicle is fitted with separate

programmable heating: it gradually brings

the engine up to a good temperature to

facilitate starting.

Digital programming control

Time setting and reading

indicator lamp

The programmable heating system control

panel is located at the bottom right of the

dashboard.

Ventilation

Setting the time of the internal clock

Immediate switching on of the

heating

Set the clock on the control panel before

programming the deferred switching on of

the heating.

Before switching on the heating, check that:

-

the temperature setting control is in the

"Hot air" position (red).

Press this button.

-

the air ﬂow setting control is in position 2.

This symbol or the previous stored time

The screen and the associated

indicator lamp come on.

and the number (e.g. 1) corresponding to

the recalled pre-selection are displayed for

ten seconds.

Press this button.

Within ten seconds, press these two setting

buttons until the correct time is displayed.

The screen and the heating

cycle indicator lamp come on

and remain on throughout the

duration of operation.

Note: if you wish to recall the other pre-

selected times, press the SET button several

times before the ten seconds have elapsed.

Press ">" to increase the hours or

"<" to decrease.

Switching on the deferred heating

Press and hold the button for

more rapid scrolling of the digits.

Switching on can be programmed between

one minute and twenty-four hours in

advance.

Within the ten seconds, press

these two setting buttons to

select the required start time.

You can store up to three different start

times, but programme one deferred start

only.

Setting of the stored time is

confirmed by clearing of the start

time, display of the pre-selection

number (e.g. 1) and increased

Reading the time

Press this button.

Note: if you wish to start the heating at a

fixed time each day, simply reprogramme

the stored time each day.

This indicator lamp comes

on, the time is displayed for

approximately ten seconds.

brightness of the screen illumination.

Press this button, the screen

becomes brighter.

3

Ventilation

Have the additional heating system

checked at least once a year at the

beginning of winter. Maintenance and

repairs should only be carried out by a

PEUGEOT dealer.

Cancelling the programming

Good practice

Press this button briefly to clear

the programmed start time.

To avoid any risk of poisoning or

asphyxiation, the additional heating must

not be used, even for short periods, in

an enclosed space such as a garage or

workshop which is not fitted with an exhaust

gas extraction system.

The screen illumination and the

pre-selection number (e.g. 1) are

switched off.

Use only genuine replacement parts.

Recalling one of the pre-selected

start times

The additional heating is supplied by the

vehicle's fuel tank.

Ensure that the fuel gauge indicator lamp is

not at reserve.

Press this button as many times

as necessary until the number

corresponding to the required

pre-selected start time (e.g. 2)

appears.

Two different types of equipment

Always switch off the additional heating

when filling with fuel to avoid any risk of fire

or explosion.

The additional heating is separate and

programmable. Before you enter the vehicle,

it gradually increases the temperature of the

engine to make starting easier.

After ten seconds, the time is cleared but

remains stored for as long as the number

(e.g. 2) and the screen remain on.

Do not park the vehicle on an inflammable

surface (dry grass, dead leaves, paper…),

there is a risk of fire.

The temperature near the heater must not

exceed 120 °C. A temperature higher than

this (for example in the case of painting in

an oven) could damage the components of

the electronic circuits.

This also facilitates passenger compartment

heating, demisting and defrosting.

Switching off the heating

Press this button.

The additional passenger compartment

heating system supplements the

standard equipment. Its operation may be

independent of the engine.

The heating cycle indicator lamp

and the screen are switched off.

The additional heating system is fitted with

a temperature limiter which cuts off the

combustion in the event of overheating due

to a lack of coolant.

Switching on of the heating may be

programmable.

Top up the coolant, then press the

programme selection control before

switching the heating on again.

Seats

SEATS

DRIVER'S SEAT

Head restraint

Press the tab to adjust the height of the

head restraint.

To remove the head restraint, press the tabs

and raise the head restraint.

Adjustable armrest

Turn the control located under the end of the

armrest.

3

Heated seat

Use this control to switch the heating of the

seat on or off.

Lumbar support

Seat cushion height adjustment

Turn the control.

Lift the handle 1 to raise

or lower the front of the seat.

Lift the handle 2 to raise

or lower the rear of the seat.

Seat with variable damping

If your seat is fitted with this system, turn the

control to adjust the level of damping to suit

the driver's weight.

Seat back angle

Forwards-backwards adjustment

Turn the control to adjust the angle of the

seat back.

Lift the control bar, located under the seat,

and adjust to the required position.

Rotating seat

If fitted on your seat, press the control to

rotate the seat by 180°.

Seats

2-SEAT FRONT BENCH

This is fitted with two seat belts.

Grab handle

This is located above the centre passenger.

Writing table

The back of the centre seat folds to form a

writing table.

Pull the handle located at the top of the seat

back cushion.

3

Seats

REAR SEATS

Seat back angle

Turn the control to adjust the

angle of the seat back.

Access to the rear seats

To gain access to row 3, manoeuvre the

control on the outer seat of row 2 and tilt the

seat back forwards.

To return the seat back to its initial position,

bring it to the vertical position without

touching the control.

Seat back folded position of the

central seat (rows 2 and 3)

The back of the central seat can be folded

fully onto the cushion and used as a cup

holder table.

Lower the head restraint then raise the

control and fold the seat back forwards.

To return the seat back to its initial position,

raise the control again.

Seats

Turn the two levers upwards.

Raise the bench seat and remove it.

REAR BENCH SEATS

Good practice

Removing the bench seat

Following the various operations:

Access to the rear seats

-

do not remove a head restraint without

storing it securely,

At least two people are required to

remove the bench seat.

Lower the head restraints then raise the

control and tilt the seat back forwards.

do not travel in row 3 with the row 2

bench seat in the vertical position,

Fold the seat back onto the cushion as

described above.

Seat back folded position

do not store any kind of object on the

folded seat back of row 2,

Turn the two levers forwards.

Remove the head restraints then tilt the seat

back as described above.

Tilt the base of the bench seat forwards to

place the assembly in the vertical position.

check that the seat belts are always

accessible and easy for the passenger

to use,

With your right hand, raise the lever then tilt

the seat back 5° towards the rear.

With your left hand, tilt the seat back

forwards onto the cushion.

-

a passenger must not take their seat

without correctly adjusting their seat's

head restraint and adjusting and

fastening their seat belt.

3

Seats

CREW CAB

Access to the box under the bench seat

From the cab

Good pratice

Consisting of an ergonomic 4-seat bench

and a high-strength partition, it offers

comfort and safety.

Do not tilt the bench seat cushion during

transportation.

Tilt the seat cushion forwards to gain access

to the large box.

No not attach anything to the cab fixing

structure.

Each seat of the bench is fitted with an

inertia reel seat belt.

Do not exceed the number of passengers

indicated on the registration certificate.

From the load space

Refer to section 5 to read the "Good

practice" recommendations.

Raise the two flaps which make the full

length at the floor available. The flaps are

retained in the raised position by magnets

on the back of the partition.

Do not install child seats, booster cushions or

carrycots on the rear seats of the crew cab.

In the rear, the load space is intended for

the transportation of goods only.

You are advised to place the goods or heavy

objects as far forwards as possible in the

load space (towards the cab) and secure

them by means of straps using the stowing

rings on the floor.

Practical information

PRACTICAL INFORMATION

CAB FITTINGS

Central storage tray

Front seat storage

Folding writing table

This may be lockable (according to

specification).

There is a storage drawer, located under the

front seat (driver's).

This is located in the centre of the fascia

panel.

The location under the passenger's seat

is used for storing the tools required when

changing a wheel.

The clip can be used to secure documents,

slips, ...

Pull or push the top of the table to unfold or

fold it.

If your vehicle is fitted with a seat with

variable vibration reduction, it does not have

any storage compartments.

If your vehicle is fitted with a front

passenger airbag, the table cannot be

raised.

3

Practical information

Glove box

Cooled glove box

Sun visor

This is located on the top left part of the

dashboard

To avoid glare from ahead, fold the sun visor

down.

The air supplied into the glove box is the

same as from the vents.

Pockets are arranged in the sun visors for

storing toll cards, tickets, ...

Practical information

12 volt socket

Cigarette lighter / Portable ashtray

Overhead storage compartment

Press and wait a few moments until the

lighter pops out automatically.

After opening the ashtray, pull it upwards

then empty it into a bin.

This is located above the sun visors.

Maximum load: approximately 20 kg.

When used as a socket: 180 W max.

3

Practical information

Fittings/storage compartment in the

door pockets

Courtesy lamp

Reading lamps

This is a double courtesy lamp located in

the centre of the roof. It can be activated by

means of:

These are controlled by the switches.

The driver's switch controls both reading

lamps simultaneously.

-

the switches located on the courtesy

lamp, with the ignition on - RUNNING

position,

The passenger switch controls either the

driver's reading lamp or the passenger

reading lamp.

-

opening or closing one of the front doors,

locking/unlocking the vehicle.

Switches on the bottom right of

the dashboard allow the driver

to switch the passenger reading

lamp on and off.

It switches off automatically:

-

if the switch is not pressed to the right or

to the left,

-

in all cases after 15 minutes, if the doors

remain open or when the ignition is

switched on.

Practical information

LOAD SPACE FITTINGS

Stowing rings

Support for stowing rail

12 volt socket

Supports for securing a stowing rail are

available above the trims, on each side of

the vehicle.

When used as a power socket: 180 W max.

Eight stowing rings are provided for securing

your loads. Six rings are located on the floor

and two on the partition behind the cab.

Trims

The lower parts of the sides are fitted with

load protection trims.

As a safety precaution in case of sharp

braking, you are advised to place heavy

objects as far forwards towards the cab as

possible.

3

Instruments and controls -> Gearbox and steering wheel for Your Peugeot Boxer Van First Generation (1994-2002)

Related Topics

Instruments and controls

Popular Owner Manuals

Latest Owner Manuals