Get Ease of use and comfort -> Remote control Guide for Peugeot Ion 4 Door First Generation (2010-2020)

Ease of use and comfort

Remote control*

This is used for remote control of the following

functions:

Buttons

Display

-

Check of the vehicle charge status.

Programming of charging: start time and

duration of charging.

-

Activation of the climate control functions

(heating, air conditioning, demisting).

3

In order to programme charging, the

following conditions must be met.

-

Place the drive selector in

position P.

1. On/Off, transmission of data.

2. MODE: used to scroll through the various

functions available (start of charging,

duration of charging, interior temperature).

3. Immediate charging of the vehicle

(resetting of the programming values to

zero).

-

Place the switch on LOCK.

Connect the vehicle using the

normal charging cable.

1. Data transmission status indicator lamp.

2. Charging indicator lamp.

3. Fault warning lamp.

The remote control has a range of

approximately 100 metres.

4. Settings.

4. Battery charge status warning lamp.

5. Charging programming functions status

indicator lamp.

6. Charging time remaining indicator.

7. Interior temperature function status

indicator lamp.

* Depending on equipment.

47

Ease of use and comfort

On / Off

Programming the start of

charging

Programming the duration

of charging

Extend the aerial.

This function is used to set the time remaining

before starting the charging of your vehicle.

(e.g. it is 19:00 at the time of programming, the

programmed charging start time is 2:00 hours:

charging will begin at 21:00).

This function is used to programme the

duration of charging of your vehicle.

Switch on the remote control.

Press the MODE button to select the

programming of the duration of charging.

Press and hold this button to switch

the remote control on or off.

If there is no action on the remote

control within 30 seconds, it will switch

off automatically.

Switch on the remote control.

This symbol is displayed on the screen.

Use the arrows to set the charging time: each

press changes the time in steps of half an hour.

Press the on/off button briefly to transmit the

data to the vehicle.

This symbol is displayed on the screen.

Use the arrows to set the charging start time:

each press changes the time in steps of half

an hour.

Press the on/off button briefly to transmit the

data to the vehicle.

The duration of charging can be

programmed between 0.5 and

19.5 hours. However, you can also

select the duration "-h": in this case,

charging will stop when the battery

is fully charged. This duration is the

default value.

If the start of charging is programmed

without programming the duration of

charging, the battery will be charged

fully.

If the duration of charging is

programmed without programming

the start time, the battery will be

charged immediately for the duration

programmed.

48

Ease of use and comfort

Cancelling the programmed Programming the interior temperature

settings

This function is used to programme the

switching on of:

Using the remote control

Activation of the functions

Switch on the remote control.

Press the MODE button to select the interior

temperature programming.

Press the immediate charging button,

then press the on/off button briefly to

transmit the data to the vehicle.

-

the heating.

the air conditioning.

the demisting.

3

In order to programme the heating, air

conditioning or demisting functions, the

following conditions must be met.

Using the switch

Place the vehicle's switch in the ON position

then return it to the LOCK position.

One of these symbols is displayed on the

screen. It indicates the current status of the

interior temperature.

-

The drive selector is in position P.

The switch is on LOCK.

The vehicle is connected using the

normal charging cable.

Use the arrows to select the function required.

Press the on/off button briefly to transit the data

to the vehicle.

The progammed values set using

the remote control are cancelled

automatically each time the vehicle is

started.

-

All of the doors are closed correctly.

The battery charge level is

sufficient (one bar minimum).

For maximum effectiveness of

the programming of the interior

temperature, ensure that all of the

vehicle's windows are closed.

49

Ease of use and comfort

Functions available

Battery charge level

indicator

Changing the batteries

Cooling: Switching on of the air

Battery type: CR2032

Unclip the housing then replace the 2 batteries.

You can check the charge status of the main

conditioning and ventilation in the

passenger compartment, via the

central vents.

battery using the remote control.

Do not discard the old batteries, take

them to an approved collection point.

Battery fully charged.

Heating: Switching on of the heating

in the passenger compartment and

of the ventilation via the lower vents.

The heating of the driver's seat will

also be activated, if the function was

activated previously.

Battery at half charge.

Battery charge low.

Demisting: Switching on of the

de-icing of the rear screen and

exterior mirrors (depending

on version), of the ventilation

and heating in the passenger

compartment, via the side vents,

of the heating of the driver's

seat, if the function was activated

previously.

Battery flat.

Deactivation of the interior

temperature programming

function and cancellation of the

programmed settings.

50

Ease of use and comfort

Operating faults

Remote control

Indicator lamps

Status

Causes

Actions / Observations

3

Flashes within approximately 10 seconds A fault has occurred.

after the remote control is switched on.

Switch the remote control off, then on

again.

Flashes within approximately 1 second

after the remote control is switched on.

Electrical interference is preventing the

operation of the remote control or the

transmission of data.

Move away from the sources of

interference.

Flashes within approximately 10 seconds The aerial has not been extended.

after the remote control is switched on.

Extend the aerial.

The range of the remote control has

been exceeded.

Move closer to the vehicle.

Place the switch in the LOCK position.

The switch is not in the LOCK position.

51

Ease of use and comfort

Programming the charging

Indicator lamps

Status

Causes

Actions / Observations

Flashes for a few seconds.

The charging cable is not connected

correctly.

Check the cable.

There is a problem with your electrical

installation.

Have your electrical installation checked

by a professional.

Flashes for a few seconds.

The drive selector is not in position P.

Place the drive selector in position P.

Programming the interior temperature

Indicator lamps

Status

Causes

Actions / Observations

Flashes for a few seconds.

The charging cable is not connected

correctly.

Check the cable.

There is a problem with your electrical

installation.

Have your electrical installation checked

by a professional.

Flashes for a few seconds.

The charge of the main battery is not

sufficient.

Charge the battery then start the

programming again.

One of the vehicle's doors is open.

Close all of the doors then start the

programming again.

The drive selector is not in position P.

Place the drive selector in position P.

52

Ease of use and comfort -> Remote control for Your Peugeot Ion 4 Door First Generation (2010-2020)

Related Topics

Ease of use and comfort