Get Audio and Telematics (Nav) Guide for Peugeot Traveller Van First Generation (2016-2026)

Audio and Telematics

emergency or assistance call

PEUGEOT Connect SOS

In an emergency, press this

button for more than 2 seconds.

Flashing of the green LeD and

a voice message confirm that

the call has been made to the

"PeugeoT Connect SoS" call

centre*.

If an impact is detected by the airbag

control unit, and independently of

the deployment of any airbags, an

emergency call is made automatically.

If you benefit from the PeugeoT

Pressing this button again immediately cancels

the request.

The green LeD goes off.

Pressing this button for more than 8 seconds

cancels the request at any time.

Connect Packs offer with the SoS and

assistance pack included, there are

additional services available to you in

your MyPeugeoT personal space, via

the Internet website for your country.

The green LeD remains on (without flashing)

when communication is established.

It goes off at the end of the call.

* Subject to the general conditions for the

service available from dealers and to

technological and technical limitations.

"PeugeoT Connect SoS" immediately locates

your vehicle, starts communication with you in

your language**, and where necessary sends

the appropriate public emergency services**. In

countries where the service is not available, or

when the locating service has been expressly

declined, the call is sent directly to the

emergency services (112) without the vehicle

location .

** Depending on the geographical cover of

"PeugeoT Connect SoS", "PeugeoT

Connect Assistance" and the official national

language selected by the owner of the vehicle.

The list of countries covered and PeugeoT

CoNNeCT services is available from dealers

328

Audio and Telematics

PEUGEOT Connect Assistance

Press this button for more than

2 seconds to request assistance

if the vehicle breaks down.

A voice message confirms that

the call has been made**.

Operation of the system

If you purchased your vehicle outside

the PeugeoT dealer network, we

invite you to have a dealer check the

configuration of these services and, if

desired, modified to suit your wishes.

In a multi-lingual country, configuration

is possible in the official national

language of your choice.

When the ignition is switched

on, the green LeD comes on for

3 seconds indicating that the

system is operating correctly.

Pressing this button again immediately cancels

the request.

If the orange LeD flashes then

goes off: there is a system fault.

The cancellation is confirmed by a voice

message.

The orange LeD is on continuously: the backup

battery must be replaced.

In either case, the emergency and assistance

calls may not function.

Contact a qualified repairer as soon as

possible.

For technical reasons and in particular

to improve the quality of "PeugeoT

CoNNeCT services" services to

customers, the manufacturer reserves

the right to carry out updates to the

vehicle's on-board telematic system.

Geo-location

You can deactivate geo-location by

simultaneously pressing the "PeugeoT

Connect SoS" and "PeugeoT Connect

Assistance" buttons, followed by a press on

"PeugeoT Connect Assistance" to confirm.

A fault with the system does not

prevent the vehicle being driven.

** Depending on the geographical cover of

"PeugeoT Connect SoS", "PeugeoT

Connect Assistance" and the official national

language selected by the owner of the vehicle.

The list of countries covered and PeugeoT

CoNNeCT services is available from dealers

To reactivate geo-location, simultaneously

press the "PeugeoT Connect SoS" and

"PeugeoT Connect Assistance" buttons

again, followed by a press on "PeugeoT

Connect Assistance" to confirm.

.

329

Audio and Telematics

PeugeoT Connect Nav

GPS satellite navigation - Connectivity - Multimedia audio - Bluetooth^®telephone

Contents

332

First steps

Steering mounted controls

Menus

334

335

Voice commands

Navigation

336

342

Connected navigation

Connectivity

358

368

Radio Media

378

Telephone

390

402

Settings

Frequently asked questions

412

The system is protected in such a way that it will only operate in

your vehicle.

As a safety measure and because it requires sustained attention

by the driver, the pairing of a Bluetooth mobile telephone with

the Bluetooth hands-free system of your audio system must be

done with the vehicle stationary and the ignition on.

The display of the energy economy mode message signals that

a change to standby is imminent. For more information on the

Energy economy mode refer to the corresponding section.

The link below gives access to oSS (open Source Software)

codes for the system.

.

331

Audio and Telematics

First steps

With the engine running, a press

use the buttons either side of the touch screen

for access to the menus, then press the virtual

buttons in the touch screen. All of the touch

areas of the screen are white.

The touch screen is of the "capacitive"

type.

mutes the sound.

With the ignition off, a press turns the

system on.

To clean the screen, use a soft,

non-abrasive cloth (spectacles cloth)

with no additional product.

Do not use sharp objects on the

screen.

each menu is displayed in one or two pages

(primary page and secondary page).

Volume.

Do not touch the screen with wet

hands.

Primary page

Secondary page

23 °C

87.5 MHz

12:13

FM/87.5 MHz

87.5MHz

332

Audio and Telematics

Short-cuts: using the virtual buttons in the

upper band of touch screen, it is possible to

go directly to the selection of audio source,

the list of stations (or titles, depending on

the source), message notifications, emails,

mapping updates and, depending on services,

navigation notifications.

23 °C

531 kHz

12:13

In the "Settings" menu you can create

a profile for just one person or a group

of people with common points, with

the possibility of entering a multitude

of settings (radio presets, audio

settings, navigation history, contact

favourites, ...); these settings are taken

into account automatically.

Select the audio source (depending on

version):

-

FM / DAB* / AM* stations.

Smartphone via MirrorLink^TMor CarPlay^®.

uSB memory stick.

Media player connected to the auxiliary

socket (jack, cable not supplied).

Telephone connected by Bluetooth* and

using Bluetooth* audio streaming.

In very hot conditions, the volume may

be limited to protect the system. It may

go into standby (screen and sound off)

for at least 5 minutes.

The return to normal takes place when

the temperature in the passenger

compartment drops.

-

.

* Depending on equipment.

333

Audio and Telematics

Steering mounted controls

Voice commands:

Increase volume.

Radio (rotate): automatic search for

the previous / next station.

Media (rotate): previous / next track,

move in a list.

Short press: Confirm a selection.

other than selection, access to

presets.

Short press, system voice

commands.

Long press, smartphone voice

commands via the system.

Mute / Restore the sound.

Decrease volume.

Media (short press): change the

multimedia source.

Radio: display the list of stations.

Media: display the list of tracks.

Radio, press and hold: update the

list of stations received.

Telephone (short press): call.

Call in progress (short press):

access to telephone menu.

Telephone (long press): reject an

incoming call, end call, access to

telephone menu.

334

Audio and Telematics

Menus

Connected navigation

Connectivity

Radio Media

23 °C

12:13

23 °C

531 kHz

12:13

23 °C

87.5 MHz

12:13

FM/87.5 MHz

87.5MHz

enter navigation settings and choose a

destination.

use services available in real time, depending

on equipment.

operate certain applications on a smartphone

connected via MirrorLink^TMor CarPlay^®.

Check the state of Bluetooth and Wi-Fi

connections.

Select an audio source, a radio station, display

photographs.

Telephone

Settings

Driving

23 °C

531 kHz

12:13

23 °C

12:13

Connect a telephone by Bluetooth^®, read

messages and emails and send quick

messages.

enter settings for a personal profile and/

or adjust the settings for sound (balance,

ambience, ...), and the display (language, units,

date, time, ...).

Activate, deactivate, adjust the settings for

certain vehicle functions.

.

335

Audio and Telematics

Voice commands

Steering mounted controls

First steps

Information - Using the system

Pressing this button activates the

voice commands function.

example of a "voice command" for

navigation:

"Navigate to address "11 Regent

Street, London"".

Press the Push To Talk

button and tell me what you'd

like after the tone. Remember

you can interrupt me at any

example of a "voice command" for

the radio and media:

"Play artist "Madonna"".

time by pressing this button. If you

press it again while I'm waiting for you

to speak, it'll end the conversation. If

you need to start over, say "cancel".

If you want to undo something, say

"undo". And to get information and tips

at any time, just say "help". If you ask

to me do something and there's some

information missing that I need, I'll

give you some examples or take you

through it step by step. There's more

information available in "novice" mode.

You can set the dialogue mode to

"expert" when you feel comfortable.

To ensure that voice commands are

always recognised by the system,

please observe the following

recommendations:

example of a "voice command" for

the telephone:

"Call David Miller".

-

speak in a normal tone without

breaking up words or raising your

voice.

-

always wait for the "beep" (audible

signal) before speaking.

for best operation, it is

recommended that the windows

and opening roof (if fitted) be

closed to avoid interference from

extraneous noises.

The voice commands, with a choice

of 12 languages (english, French,

Italian, Spanish, german, Dutch,

Portuguese, Polish, Turkish, Russian,

Arabic, Brazilian), are made using the

language previously chosen and set in

the system.

-

before making a voice command,

ask other passengers to not speak.

The voice commands in Arabic for:

"Navigate to address" and "Display PoI

in the city", are not available.

336

Audio and Telematics

Global voice commands

These commands can be made from any screen page after pressing the voice command or telephone button located on the steering wheel, as

long as there is no telephone call in progress.

"Voice command"

Help message

Help

Voice command help

Navigation help

Radio help

There are lots of topics I can help you with.

You can say: "help with phone", "help with navigation", "help with media" or "help with

radio". For an overview on how to use voice controls, you can say "help with voice

controls".

Media help

Telephone help

Set dialogue mode as <...>

Select profile <...>

Yes

Select "beginner" or "expert" mode.

Select profile 1, 2 or 3.

Say "yes" if I got that right. otherwise, say "no" and we'll start that again.

No

.

337

Audio and Telematics

"Navigation" voice commands

These commands can be issued from any screen page after pressing the voice command or telephone button on the steering wheel, as long as

there is no telephone call in progress.

"Voice command"

Help message

Navigate home

To start guidance or add a stopover, say "navigate to" and then the address or contact

name.

Navigate to work

For example, "navigate to address 11 Regent Street, London", or "navigate to contact,

John Miller".

Navigate to preferred address <...>

Navigate to contact <...>

Navigate to address <...>

Show nearby POI <...>

Remaining distance

Remaining time

You can specify if it's a preferred or recent destination. For example, "navigate to preferred

address, Tennis club", "navigate to recent destination, 11 Regent Street, London".

otherwise, just say, "navigate home". To see points of interest on a map, you can say

things like "show hotels in Banbury" or "show nearby petrol station".

For more information you can ask for "help with route guidance".

To get information about your current route, you can say "tell me the remaining time",

"distance" or "arrival time".

Try saying "help with navigation" to learn more commands.

Arrival time

Stop route guidance

Depending on the country, give the destination instructions (address) in the language used by the system.

338

Audio and Telematics

"Radio Media" voice commands

These commands can be issued from any screen page after pressing the voice command or telephone button on the steering wheel, as long as

there is no telephone call in progress.

"Voice command"

Help message

You can pick a radio station by saying "tune to" and the station name or frequency.

For example "tune to channel Talksport" or "tune to 98.5 FM". To listen to a preset radio

station, say "tune to preset number". For example "tune to preset number five".

Tune to channel <...>

To display the details of the current "track", "artist" and "album", you can say "What's

playing"

What's playing

Play song <...>

Play artist <...>

Play album <...>

use the command "play" to select the type of music you'd like to hear. You can pick by

"song", "artist", or "album". Just say something like "play artist, Madonna", "play song, Hey

Jude", or "play album, Thriller".

Media voice commands are available only for a uSB connection.

.

339

Audio and Telematics

"Telephone" voice commands

If a telephone is connected to the system, these voice commands can be issued from any main screen page after pressing the telephone

button on the steering wheel, as long as there is no telephone call in progress.

If there is no telephone connected by Bluetooth, a voice message announces: "Please first connect a telephone" and the voice session will be

closed.

"Voice command"

Help message

Call contact <...>*

Dial <...>*

To make a phone call, say "call" followed by the contact name, for example: "Call David

Miller".

You can also include the phone type, for example: "Call David Miller at home".

To make a call by number, say "dial" followed by the phone number, for example,

"Dial 107776 835 417".

Display contacts*

Display calls*

You can check your voicemail by saying "call voicemail".

To send a text, say "send quick message to", followed by the contact, and then the name

of the quick message you'd like to send.

For example, "send quick message to David Miller, I'll be late".

To display the list of calls, say "display calls".

For more information on SMS, you can say "help with texting".

Call (message box | voicemail)*

* This function is available only if the telephone connected to the system supports downloading of contacts and recent calls and if the download has

been done.

340

Audio and Telematics

"Test message" voice commands

If a telephone is connected to the system these voice commands can be issued from any main screen page after pressing the telephone button

on the steering wheel, as long as there is no telephone call in progress.

If no telephone has been connected by Bluetooth, a voice message announces: "Please first connect a telephone" and the voice session will be

closed.

"Voice command"

Help message

To hear your messages, you can say "listen to most recent message".

When you want to send a text, there's a set of quick messages ready for you to use.

Just use the quick message name and say something like "send quick message to Bill

Carter, I'll be late".

Send text to <...>

Check the phone menu for the names of the supported messages.

Please say "call" or "send quick message to", and then select a line from the list.

To move around a list shown on the display, you can say "go to start", "go to end", "next

page" or "previous page".

To undo your selection, say "undo".

To cancel the current action and start again, say "cancel".

Listen to most recent message*

The system only sends predefined "Quick messages".

* This function is only available if the telephone connected to the system supports downloading of contacts and recent calls and if the download has

been done.

.

341

Audio and Telematics

Navigation

Level 1

Level 2

Level 3

23 °C

12:13

23 °C

12:13

1

342

Audio and Telematics

Level 1

Level 2

Level 3

Comments

Navigation

Select the orientation of the map; north up,

vehicle direction up or perspective.

Navigation

Display the traffic information available.

Manually locate an area on the world map or

enter the latitude and longitude coordinates.

World map

Around the vehicle

Around home

Display the location criteria selected.

Navigation

Around the destination

2D mode

Switch to a 2D map.

Zoom out.

Zoom in.

Start navigation to the current address.

Save the current address.

Zoom out.

Zoom in.

.

343

Audio and Telematics

Level 1

Level 2

Level 3

Point of interest on map

23 °C

12:13

2

3

4

5

6

7

23 °C

12:13

1

344

Audio and Telematics

Level 1

Level 2

Stations

Level 3

Comments

Activate or deactivate the content available

(stations, car parks, risk areas and danger

areas).

Car park

Danger area

Map color

Select day or night mode for display of the map.

Travel

2

3

4

5

6

Active life

Commercial

Public

Select the PoIs available.

POI on map

geographic

Select all

Confirm

Navigation

Select or deselect all.

Save your choice or selection.

Select or modify a city.

Modify city

Weather

7

Petrol Station

Car park

Display on the map the content available in non-

connected mode.

View map

Traffic

Danger area

Select PoI

Select from the PoIs available.

Zoom out.

.

Zoom in.

345

Audio and Telematics

Level 3

Level 4

Level 5

Filling stations located

Car parks around the vehicle

346

Audio and Telematics

Level 3

Zoom in

Level 4

Level 5

Comments

Confirm

Zoom in around the city selected.

Select a location option.

Around the vehicle

on the route

At the destination

Weather

Weather information transmitted in TMC mode.

Filling stations around the vehicle

Filling stations on the route

Filling stations at the destination

Car parks around the vehicle

Car parks on the route

Filling stations

Display the list of PoIs.

Car park

Car parks at the destination

Zoom out.

Zoom in.

.

347

Audio and Telematics

Level 3

Level 4

Level 5

Traffic observed

List of danger areas

Select POI

348

Audio and Telematics

Level 3

Traffic

Level 4

Level 5

Traffic observed

Comments

Traffic information sent in real time.

Display the list of danger areas (roadworks,

breakdowns, accidents, ...).

Danger area

List of danger areas

Select PoI

Configure a category of PoI to display.

.

349

Audio and Telematics

Level 1

Level 2

Level 3

1

My destinations

Navigation menu

8

9

10

Find a point of interest

11 12 13 14 15

16

17

18

350

Audio and Telematics

Level 1

Level 2

Level 3

Comments

Navigation

Select the country.

Save the current address.

Secondary page

Enter address

1

Confirm

Confirm the current address.

Recent

8

9

Navigation

My home

My work

Display the lists of destinations and start

navigation.

Preferred

Contact

Secondary page

My destinations

10

Delete one or more destinations.

Travel

11

12

13

14

15

Active life

Commercial

Public

Navigation

List of categories available.

After selection of category, select the point of

interest.

Secondary page

Points of interest

1

Geographic

Search

Search for a point of interest.

enter a point of interest.

Point of interest

Address

16

17

Navigation

Secondary page

Search

enter the address of a point of interest.

enter settings for the PoI search mode in a

local or connected database depending on the

services subscribed to.

18 Local / Connected

.

Confirm

Confirm the entry.

351

Audio and Telematics

Level 1

Level 2

Level 3

Guidance criteria

1

Add waypoint

Navigation menu

Route and waypoints

19

20

Settings

21 22 23 24 25

352

Audio and Telematics

Level 1

Level 2

Level 3

Comments

Fast

Short

Navigation

Select the guidance criteria (motorways, tolls and

how traffic is taken into account).

Compromise

Ecological

See on map

Confirm

Secondary page

Guidance criteria

1

Display the route selected using the criteria.

Save your selections.

Waypoints

Route

Display the waypoints saved.

Display details of the route.

Add a waypoint from a list offered.

Display the map.

19

20

Navigation

Add waypoint

Preview

Add a waypoint

Secondary page

Routes / waypoints

1

Finish

Press to calculate the route.

Delete one or more waypoints.

Move a waypoint in the list.

Aspects

Options

Alerts

21

22

23

24

25

Navigation

Secondary page

Settings

enter choices and select the volume for the voice

and stating the names of streets.

1

Vocal

Mapping

Confirm

Save the selections adopted.

.

353

Audio and Telematics

Choosing a new destination

Towards a new destination

Towards a recent destination

Press Navigation to display the

primary page.

To use the navigation system, it is

necessary to enter the "City", the

"Street" and the "Number" using the

virtual keypad, or to take them from the

list of "Contacts" or from the "History"

of addresses.

Press Navigation to display the

primary page.

Press the "MENU" button to go to the

secondary page.

Press the "MENU" button to go to the

secondary page.

1

Select "Enter address".

Select the "Country".

Select "My destinations".

Without confirmation of the street

number, you will be guided to one end

of the street.

Select the "Recent" tab.

8

enter the "City", the "Street" and the

"Number" and confirm by pressing

on the suggestions displayed.

Select the address chosen in the list to display

the "Guidance criteria".

Press "Confirm" to select the

"Guidance criteria".

Press "Confirm" to start navigation.

And / or

Select "See on map" to select the

"Guidance criteria".

Select "Position" to see the point of

arrival geographically.

Press "Confirm" to start navigation.

354

Audio and Telematics

Towards "My home" or

"My work"

Towards a contact

Towards points of interest (POI)

Press Navigation to display the

Points of Interest (PoI) are listed in different

primary page.

categories.

Press the "MENU" button to go to the

Press Navigation to display the

secondary page.

primary page.

1

9

1

Select "My destinations".

Select the "Preferred" tab.

Select "My home".

Select "My destinations".

Select the "Contact" tab.

Press the "MENU" button to go to the

secondary page.

1

Select "Points of interest".

10

Select the "Travel", or "Leisure"

or "Commercial" or "Public" or

"Geographic" tab.

Select a contact in the list offered to start

navigation.

or

Select "My work".

Select "Search" to enter the name

and address of a PoI.

Select a previously saved favourite destination.

Press "Confirm" to start calculation

of the route.

.

355

Audio and Telematics

Towards a point on the map

Towards GPS coordinates

Press Navigation to display the

primary page.

Press Navigation to display the

primary page.

A marker is displayed in the middle of

the screen, with the "Latitude" and

"Longitude" coordinates.

explore the map by sliding a finger on the

screen.

explore the map by sliding a finger on the

screen.

Press this button to start navigation.

Select the destination by pressing on the map.

Press this button to display the world

map.

or

Press this button to save the address

displayed.

using the grid, select by zoom the

desired country or region.

Tap the screen to place a marker and

display the sub-menu.

or

Press this button to enter the gPS

coordinates.

Press this button to start navigation.

Press this button to enter the value

for "Latitude" using the virtual

keypad.

or

And

Press this button to save the address

displayed

Press this button to enter the value

for "Longitude" using the virtual

keypad.

A long press on a point opens a list of

PoIs nearby.

356

Audio and Telematics

TMC (Traffic Message

Channel)

TMC (Traffic Message Channel) is a

european standard on the broadcasting

of traffic information via the RDS

system on FM radio, transmitting traffic

information in real time.

The TMC information is then displayed

on a gPS Navigation system map and

taken into account straight away during

navigation, so as to avoid accidents,

traffic jams and closed roads.

The display of danger areas depends

on the legislation in force and

subscription to the service.

.

357

Audio and Telematics

Connected navigation

Depending on the equipment level of the vehicle

Network connection provided by the vehicle

OR

Network connection provided by the user

23 °C

12:13

358

Audio and Telematics

Connected navigation connection

on the arrival of "ToMToM

TRAFFIC", the services are

available.

Network connection provided by

As a safety measure and because it

requires sustained attention by the

driver, using a smartphone when

driving is prohibited.

All operations must be done with the

vehicle stationary.

the user

USB connection

Connect the uSB cable.

The smartphone is in charge mode

when connected by uSB cable.

The services offered with connected

navigation are as follows.

A connected services pack:

Bluetooth connection

-

Weather,

Filling stations,

Car park,

Traffic,

PoI, local search.

For access to connected navigation, you

can use the connection provided by the

vehicle via the "emergency or assistance

call" services or use your smartphone as

a modem.

Activate the Bluetooth function on the

telephone and ensure that it is visible

to all (see the "Connectivity" section).

A Danger area pack.

Activate and enter settings for sharing

the smartphone connection.

Wi-Fi connection

Select a Wi-Fi connection found by

the system and connect to it (see the

"Connectivity" section).

The principles and standards

are constantly changing. For

Restrictions of use:

With CarPlay^®, connection sharing is

only with a Wi-Fi connection.

With MirrorLink^TM, connection

sharing is only with a uSB

connection.

Network connection provided by

the vehicle

-

communication between your

smartphone and the system to operate

correctly, we recommend that you

keep your smartphone's operating

system up to date, and the time and

date on your smartphone and the

system correct.

-

The system is automatically

connected to the modem included

for the "emergency or assistance

calls" services and does not require

a connection provided by the user via

their smartphone.

The quality of services depends on the

quality of the network connection.

.

359

Audio and Telematics

Level 1

Level 2

Level 3

23 °C

12:13

Point of interest on map

26 27 28 29 30

23 °C

12:13

23 °C

12:13

1

23 °C

12:13

7

360

Audio and Telematics

Level 1

Level 2

Level 3

Comments

Navigation

Select the orientation of the map; north up,

vehicle direction up or perspective.

on connection of the system to a network,

"ToMToM TRAFFIC" is displayed instead of

"TMC", for use of all of the options available, in

real time.

Navigation

TOMTOM TRAFFIC

Weather

Stations

Car park

Traffic

Select the options.

The map display the route chosen, depending on

options.

Danger area

Map color

Select the display mode for the map.

Navigation

Commercial

geographic

Leisure

26

27

28

29

30

Select the PoIs available.

POI on map

View map

Public

Travel

Confirm

Save the options.

Select or change a city.

Zoom out.

Modify city

7

Zoom in.

.

361

Audio and Telematics

Level 3

Level 4

Level 5

Weather information

Filling stations located

31

32

Sort by spaces

362

Audio and Telematics

Level 3

Level 4

Level 5

Comments

Select or change a city.

Select city

Confirm

Around the vehicle

on the route

Select or change a city.

At the destination

Display the weather forecast for the day or the

following days.

Weather

Weather information

Filling stations around the vehicle

Filling stations on the route

Filling stations at the destination

By distance

Display the list of filling stations and the

associated information (address, prices,

fuels, ...).

Filling stations

31

32

By price

Car parks around the vehicle

Car parks on the route

Car parks at the destination

Sort by distance

Display the list of car parks and the associated

information (address, distance, spaces available,

price, ...).

Car park

Sort by spaces

Sort by price

Zoom out.

Zoom in.

.

363

Audio and Telematics

Level 3

Level 4

Level 5

Traffic observed

List of danger areas

Select POI

364

Audio and Telematics

Level 3

Traffic

Level 4

Level 5

Traffic observed

Comments

Display traffic information in real time: type,

description and duration (in minutes).

Display danger areas (roadworks, breakdowns,

accidents, ...) in real time.

Danger areas

List of danger areas

Points of

interest

Points of interest

Select PoI

Display the list of PoIs for the location selected.

.

365

Audio and Telematics

Display the weather

Settings specific to

connected navigation

Press Navigation to display the

primary page.

Press Navigation to display the

primary page.

For access to connected navigation,

you have to select the option:

"Authorise sending information".

Press the "MENU" button to go to the

Press this button to display the list of

services.

secondary page.

1

The display of danger zones is

conditioned by the legislation in force

and subscription to the service.

Select "Settings".

Select "View map".

Select "Weather".

Select "Options".

22

Activate or deactivate:

Press this button to display the first

level of information.

-

"Allow declaration of danger

areas"

"Guidance to final destination

on foot"

"Authorise sending

information"

Press this button to display the

detailed weather information.

Select "Alerts".

The temperature displayed at 6 o'clock

in the morning will be the maximum

temperature for the day.

The temperature displayed at 6 o'clock

in the evening will be the minimum

temperature for the night.

23

Activate or deactivate "Warn of

danger zones".

366

Audio and Telematics

Declaration of "Danger

areas"

You can download updates to the

system, danger zones and mapping,

from the brand's website.

The download procedure can be found

in the same place.

To distribute information on the

declaration of danger zones, you

should check the option: "Allow

declaration of danger areas".

Press Navigation to display the

primary page.

Press the "Declare a new danger

area" button located in the upper bar

of the touch screen.

Select the option "Type" to choose

the type of "Danger area".

Select the "Speed" option and enter

it using the virtual keypad.

Press "Confirm" to save and

distribute the information.

.

367

Audio and Telematics

Connectivity

Functionalities available according to equipment.

Level 1

Level 2

Level 3

Bluetooth connection

2

3

23 °C

531 kHz

12:13

Wi-Fi network connection

Networks

1

4

5

6

Connections and subscriptions to services

Share Wi-Fi connection

7

8

368

Audio and Telematics

Functionalities available according to equipment.

Level 2

Level 3

Comments

Display all telephones, connected or

disconnected.

All

2

Connectivity

Secondary page

1

Connected

Display all connected telephones.

Start a search for a device to connect.

Display secured Wi-Fi networks.

3

Bluetooth

connection

Search

Secured

4

Connectivity

Secondary page

1

Not secured

Display non-secured Wi-Fi networks.

Display remembered Wi-Fi networks.

5

Wi-Fi network

connection

Stored

6

Connectivity

Display the state of the subscription to connected

services, the state of the network connection and

the connection mode.

Secondary page

1

Manage connection

Activate or deactivating the sharing of the Wi-Fi

connection.

Activation

7

Connectivity

Secondary page

Select a Wi-Fi network found by the system and

connect to it.

1

Settings

8

Share Wi-Fi

connection

Save settings.

.

369

Audio and Telematics

Bluetooth connection^®

Procedure from the system

Connection sharing

As a safety measure and because it

requires sustained attention by the

driver, the pairing of a Bluetooth mobile

telephone with the Bluetooth hands-

free system of your audio system must

be done with the vehicle stationary

and the ignition on.

Press on "Telephone" to display the

secondary page.

The system offers to connect the

telephone with 3 profiles:

-

"Telephone" (hands-free kit, telephone

only),

"Streaming" (wireless play of audio files

on the telephone),

Press on the "OPTIONS" button to

go to the secondary page.

1

"Mobile internet data".

Press on "Bluetooth connection".

The "Mobile internet data" profile

must be activated for connected

navigation (where the vehicle does not

have "emergency and assistance call"

services), having first activated sharing

of this connection on your smartphone.

Activate the Bluetooth function on the

telephone and ensure that it is "visible

to all" (telephone configuration).

Select "Search".

The list of detected telephones is

displayed.

Procedure from the telephone

If the pairing procedure fails, it is recommended

that you deactivate and then reactivate the

"Bluetooth" function in your telephone.

Select the name of the system in the

list of devices detected.

Select one or more profiles.

In the system, accept the connection request

from the telephone.

Select the name of the chosen

telephone in the list.

Press on "Confirm".

To complete the pairing, whichever

procedure used (from the telephone or

from the system), ensure that the code

is the same in the system and in the

telephone.

Depending on the type of telephone,

you may be asked to accept or not the

transfer of your contacts and messages.

370

Audio and Telematics

Wi-Fi connection

Sharing the Wi-Fi connection Managing connections

Network connection by the smartphone Wi-Fi.

Creation of a local Wi-Fi network by the

Press Connectivity to display the

system.

primary page.

Press "Connectivity" to display the

Press Connectivity to display the

primary page.

Press the "OPTIONS" button to go to

the secondary page.

1

Press the "OPTIONS" button to go to

the secondary page.

Select "Manage connection".

1

Select "Wi-Fi network connection".

Select "Share Wi-Fi connection".

With this function you can view the access

to connected services, the availability of

connected services and modify the connection

mode.

Select the "Secured", "Not secured"

or "Stored" tab.

Select the "Activation" tab to

activate or deactivate sharing of the

Wi-Fi connection.

7

And / or

Select a network.

Select the "Settings" to change the

name of the system network and the

password.

8

using the virtual keypad, enter the

"Key" for the Wi-Fi network and the

"Password".

Press "Confirm".

Press "Confirm" to start the

connection.

To protect from any piracy and provide

maximum security for your systems,

it is recommended that you use a

security code or complex password.

The Wi-Fi connection and the sharing

of the Wi-Fi connection are exclusive.

.

371

Audio and Telematics

MirrorLink^TMsmartphone connection

23 °C

531 kHz

12:13

372

Audio and Telematics

once connection is established, a page

As a safety measure and because it

requires the sustained attention of

the driver, using a smartphone when

driving is prohibited.

As a safety measure, applications

can only be viewed with the vehicle

stationary; display is interrupted once

the vehicle is moving.

is displayed with the applications already

downloaded to your smartphone and adapted

to MirrorLink^TMtechnology.

operation must be with the vehicle

stationary.

Access to the different audio sources remains

accessible in the margin of the MirrorLink^TM

display, using touch buttons in the upper bar.

Access to the menus for the system is possible

at any time using the dedicated buttons

The "MirrorLink^TM" function requires

the use of a compatible smartphone

and applications.

When connecting a smartphone to

the system, it is recommended that

Bluetooth^®be started on the smartphone

The synchronisation of a

smartphone allows applications on a

smartphone that are adapted to the

MirrorLink^TMtechnology to be displayed

in the vehicle's screen.

There may be a wait for the availability

of applications, depending on the

quality of your network.

Connect a uSB cable. The

smartphone charges when

connected by a uSB cable.

The principles and standards

are constantly evolving. For the

communication process between

the smartphone and the system to

work correctly, the smartphone must

be unlocked; update the operating

system of your smartphone as

well as the date and time in the

smartphone and the system.

For the list of eligible smartphones,

connect to the brand's internet website

in your country.

From the system, press on

"Connectivity" to display the primary

page.

Press "MirrorLink^TM" to start the

application in the system.

Depending on the smartphone, it may be

necessary to activate the "MirrorLink^TM" function.

During the procedure, several screen

pages relating to certain functions

are displayed.

Accept to start and end the

connection.

.

373

Audio and Telematics

Level 1

Level 2

Level 3

23 °C

531 kHz

12:13

374

Audio and Telematics

Level 1

Level 2

Level 3

Comments

go to or return to the applications already

downloaded to your smartphone and adapted to

MirrorLink^TMtechnology.

go to a menu list depending on the application

chosen.

"Back": abandon the current operation, go up

one level.

"Home": go to or return to the "Car mode" page

on your smartphone.

Connectivity

MirrorLink^TM

go to the primary page of the "Connectivity"

menu.

.

375

Audio and Telematics

CarPlay^®smartphone connection

23 °C

531 kHz

12:13

376

Audio and Telematics

Connect a uSB cable. The

smartphone charges when

connected by a uSB cable.

As a safety measure and because it

requires the sustained attention of

the driver, using a smartphone when

driving is prohibited.

operation must be with the vehicle

stationary.

on connecting the uSB cable, the

CarPlay^®function deactivates the

system's Bluetooth^®mode.

Press "Telephone" to display the

CarPlay ^®interface.

The synchronisation of a

or

smartphone allows applications on a

smartphone that are adapted to the

CarPlay^®technology to be displayed

in the vehicle's screen, having first

activated the CarPlay^®function in your

smartphone.

Connect a uSB cable. The

smartphone charges when

connected by a uSB cable.

As the principles and standards

are constantly changing, it is

recommended that you keep your

smartphone's operating system

updated.

For the list of eligible smartphones, go

to the brand's internet website in your

country.

In the system, press "Connectivity"

to display the primary page.

Press "CarPlay" to display the

CarPlay^®interface.

.

377

Audio and Telematics

Radio Media

Level 1

Level 2

23 °C

87.5 MHz

12:13

FM/87.5 MHz

87.5MHz

23 °C

87.5 MHz

12:13

FM/87.5 MHz

87.5MHz

23 °C

531 kHz

12:13

AM/531 kHz

PO

kHz

1

2

3

4

1

2

3

4

Radio stations

378

Audio and Telematics

Level 1

Level 2

Comments

Radio

USB

Radio Media

Source

iPod

Select change of source.

AUX

Bluetooth

Frequency

Presets

FM

Carry out an automatic or manual search for

radio stations.

Radio Media

Frequency /

Presets

Make a long press on an empty location to preset

a station.

2

Radio Media

Band

DAB

Press Band to change waveband.

3

4

AM

Radio Media

List

open the list of radio stations and press on a

radio station to select it.

Radio stations

.

379

Audio and Telematics

Level 1

Level 2

Audio settings

1

5

6

7

8

9

Radio-media options

Radio settings

5

6

7

8

9

Audio settings

10

11

Radio stations

5

6

7

8

9

12

13

14

15

380

Audio and Telematics

Level 1

Level 2

Comments

Ambience

Distribution

Sound

Select the sound ambience.

5

6

7

8

9

Sound distribution by the Arkamys^®system.

Radio Media

Secondary page

Audio settings

Adjust the volume or activate volume linked to

speed.

1

Voice

Adjust the voice volume.

Adjust the ringtone volume.

Save settings.

Ringtone

Confirm

General

Announcements

Confirm

FM

10

11

Radio Media

Secondary page

Radio settings

Activate or deactivate settings.

Save settings.

12

13

14

15

Display the list of radio stations for the band

selected.

DAB

Radio Media

Secondary page

Radio stations

AM

Presets

Frequency

Select a preset radio station.

1

enter a frequency manually.

Change the screen display mode.

update the list according to reception.

.

381

Audio and Telematics

Level 1

Level 2

1

Radio-media options

USB

16 17 18 19 20

Photos

21

382

Audio and Telematics

Level 1

Level 2

Comments

Albums

Artists

16

17

Radio Media

Secondary page

Music files

Genres

Playlists

Folders

Choose a selection mode.

1

18

19

20

Radio Media

Secondary page

Managing photos

Display photos.

The system supports the following image

formats: .gif, .jpg, .jpeg, .bmp, .png, .raw and .tiff

with a maximum file size of 10 Mb per image.

USB

21

.

383

Audio and Telematics

Radio

Selecting a station

Preset a station

Press Radio Media to display the

menu.

Press "Frequency".

Select a radio station or frequency (refer to the

corresponding section).

2

Press "Presets".

Press "Frequency".

enter the values using the virtual

keypad.

First enter the units then click on the

decimals zone to enter the figures

after the decimal point.

2

Make a long press on one of the

buttons to preset the station.

Press one of the buttons for an

automatic search for radio stations.

Press "Confirm".

or

Move the cursor for a manual search

for frequencies up or down.

Radio reception may be affected by

the use of electrical equipment not

approved by the brand, such as a uSB

charger connected to the 12 V socket.

The exterior environment (hills,

buildings, tunnel, car park, below

ground...) may prevent reception,

even in RDS station tracking mode.

This phenomenon is normal in the

propagation of radio waves and is in no

way indicative of a fault with the audio

system.

Press Radio Media to display the

primary page.

Press the "OPTIONS" button to go to

the secondary page.

1

Select "Radio stations" in the

secondary page.

384

Audio and Telematics

Activate/ Deactivate RDS

Display text information

Play TA messages

Press Radio Media to display the

primary page.

The "radiotext" function allows

information transmitted by the radio

station and related to the station or the

song playing to be displayed.

The TA (Traffic Announcement)

function gives priority to TA alert

messages. To operate, this function

needs good reception of a radio station

that carries this type of message. While

traffic information is being broadcast,

the current media is automatically

interrupted so that the TA message can

be heard. Normal play of the media

previously playing is resumed at the

end of the message.

Press the "OPTIONS" button to go to

the secondary page.

1

Select "Radio settings".

Press Radio Media to display the

primary page.

Select "General".

10

Press the "OPTIONS" button to go to

the secondary page.

1

Activate/deactivate "Station follow".

Select "Radio settings".

Press "Confirm".

Select "General".

Select "Announcements".

10

11

RDS, if activated, allows you to continue

listening to the same station by automatic

retuning to alternative frequencies. However,

in certain conditions, coverage of an RDS

station may not be assured throughout the

entire country as radio stations do not cover

100 % of the territory. This explains the loss

of reception of the station during a journey.

Activate / Deactivate "Display radio

text".

Activate / Deactivate "Traffic

announcement".

Press "Confirm".

.

385

Audio and Telematics

DAB radio (Digital Audio Broadcasting)

Terrestrial Digital Radio

Display of the name of the current station

and "multiplex" being listened to, also

called an "ensemble".

Select audio source.

Previous "Multiplex".

Previous radio station.

Display "Radiotext" for the

current station.

Display of options:

if active but not available,

the display will be greyed

out.

Next "multiplex".

Next radio station.

if active and available, the

display will be clear.

Display of the list of radio

stations.

Secondary page.

Change of band.

Switch between the page with the presets and the page

with the frequencies.

If the current "DAB" station is not available on

"FM" the "DAB/FM" option is greyed out.

386

Audio and Telematics

Digital radio

DAB / FM auto tracking

Digital radio provides higher quality

reception.

The different multiplexes offer a

choice of radio stations arranged in

alphabetical order.

"DAB" does not cover 100% of the

territory.

If "DAB / FM auto tracking" is activated,

there is a difference of a few seconds

when the system switches to "FM"

analogue radio with sometimes a

variation in volume.

once the digital signal is restored,

the system automatically changes back

to "DAB".

When the digital radio signal is poor,

"DAB/FM auto tracking" allows you to

continue listening to the same station,

by automatically switching to the

corresponding "FM" analogue station

(if there is one).

Press Radio Media to display the

primary page.

Press Radio Media to display the

primary page.

If the "DAB" station being listened to

is not available on "FM" ("DAB/FM"

option greyed out), or "DAB/FM auto

tracking" is not activated, the sound

will cut out while the digital signal is too

weak.

Press the "OPTIONS" button to go to

the secondary page.

Select the audio source.

1

Select "Radio settings".

Press "Band" to select the "DAB"

waveband.

3

Select "General".

10

Activate / Deactivate "Station

follow".

Press "Confirm".

.

387

Audio and Telematics

Media

USB player

Auxiliary (AUX) socket

Selecting the source

Press Radio Media to display the

primary page.

Select "Source".

Choose the source.

Bluetooth^®audio streaming

Insert the uSB memory stick into the uSB port

or connect the uSB device to the uSB port

using a suitable cable (not supplied).

This source is only available if "Auxiliary input"

has been checked in the audio settings.

Streaming allows you to listen to music from

your telephone.

The system builds playlists (in temporary

memory), an operation which can take from

a few seconds to several minutes at the first

connection.

Reduce the number of non-music files and the

number of folders to reduce the waiting time.

The playlists are updated every time the

ignition is switched off or connection of a uSB

memory stick. The lists are memorised: if they

are not modified, the subsequent loading time

will be shorter.

Connect the portable device (MP3 player…) to

the auxiliary Jack socket using an audio cable

(not supplied).

The Bluetooth profile must be activated. First

adjust the volume on your portable device (to a

high level).

Then adjust the volume of your audio system.

First adjust the volume of your portable device

(to a high level). Then adjust the volume of your

audio system.

Display and management of the controls are

via the portable device.

If play does not start automatically, it may be

necessary to start the audio playback from the

telephone.

Control is from the portable device or by using

the audio system buttons.

once connected in streaming mode,

the telephone is considered to be a

media source.

388

Audio and Telematics

Connecting Apple^®players

Information and advice

Connect the Apple^®player to the uSB port

using a suitable cable (not supplied).

Play starts automatically.

The audio equipment will only play audio

files with ".wma, .aac, .flac, .ogg and

.mp3" file extensions and with a bit rate of

between 32 Kbps and 320 Kbps.

It also supports VBR (Variable Bit Rate) mode.

No other type of file (.mp4, ...) can be played.

".wma" files must be of the standard wma 9 type.

The sampling rates supported are 32, 44 and

48 KHz.

The system supports uSB mass

storage devices, BlackBerry^®devices

or Apple^®players via uSB ports. The

adaptor cable is not supplied.

Control is via the audio system.

Control of the peripheral device is with

the audio system controls.

other peripherals, not recognised on

connection, must be connected to the

auxiliary socket using a Jack cable (not

supplied) or via Bluetooth streaming,

depending on compatibility.

The classifications available are those

of the portable device connected

(artists / albums / genres / playlists /

audiobooks / podcasts).

The default classification used is by

artist. To modify the classification used,

return to the first level of the menu

then select the desired classification

(playlists for example) and confirm

to go down through the menu to the

desired track.

It is advisable to restrict file names to

20 characters, without using of special

characters (e.g.: " " ? ; ù) to avoid any playing

and displaying problems.

use only uSB memory sticks formatted FAT 32

(file allocation table).

It is recommended that the uSB cable

for the portable device is used.

The version of software in the audio system

may not be compatible with the generation of

your Apple^®player.

.

389

Audio and Telematics

Telephone

Level 1

Level 2

Level 3

23 °C

531 kHz

12:13

Contacts and favourites

1

Known devices

4

5

6

7

12

13

14

23 °C

531 kHz

12:13

Recent calls

1

2

3

8

9

10

11

390

Audio and Telematics

Level 1

Level 2

Level 3

Comments

All

4

5

6

7

View contacts according to presentation choices.

Select a contact or a favourite saved in the

system via the profile selected to start the call.

Telephone

Address

Favourites

Sort the contacts by Surname-First name or First

name-Surname.

Telephone

Bluetooth

Contact

update the contacts from the telephone.

2

Search

Create

Confirm

Search for a contact in the directory.

Telephone

Address

email

12

13

14

Create a new contact in the system.

Confirm

All

8

9

Telephone

Bluetooth

Calls

Incoming

Outgoing

Missed

View calls according to choice of presentation.

Select a contact to start the call.

10

11

3

View details for the contact.

.

391

Audio and Telematics

Level 1

Level 2

Bluetooth connection

1

15

16

Settings - Bluetooth

Messages

17

18

19

Email

20

21

22

392

Audio and Telematics

Level 1

Level 2

Comments

Display all telephones, connected or

disconnected, recognised by the system.

All

15

16

Telephone

Secondary page

1

Connected

Search

All

Display all connected telephones.

Bluetooth

connection

Start the search for a device to connect.

17

18

19

20

Telephone

Secondary page

Messages

Received

Sent

Display messages according to the choice made.

Received

Sent

Telephone

Secondary page

Email

21

22

Display emails according to the choice made.

1

Not read

Mailbox

.

393

Audio and Telematics

Level 1

Level 2

Options

1

Settings - Bluetooth

Options

23 24 25 26

Quick messages

27

28

29

30

394

Audio and Telematics

Level 1

Level 2

Comments

Make driving safe.

Security

Voicemail

Ringtone

Statistics

Confirm

Delayed

My arrival

Not available

Other

23

24

25

enter and save the number for the telephone

voicemail.

Telephone

Secondary page

Options

Adjust the ringtone volume.

Display data for the telephone connected.

Save the options.

1

26

27

28

Telephone

Select a quick message from the categories, as

required.

Secondary page

Quick messages

1

29

30

Create

Create a quick message.

.

395

Audio and Telematics

Pairing a Bluetooth^®telephone

Procedure from the system

Connection sharing

As a safety measure and because it

requires sustained attention by the

driver, the pairing of a Bluetooth mobile

telephone with theBluetooth hands-free

system of your audio system must be

done with the vehicle stationary and

the ignition on.

Press Telephone to display the

primary page.

The system offers to connect the telephone

with 3 profiles:

-

Telephone (hands-free kit, telephone

only),

Streaming (wireless play of audio files on

the telephone),

Press Connect telephone.

Mobile internet data.

or.

The "Mobile internet data" profile

must be activated for connected

navigation, having first activated

sharing of this connection on your

smartphone.

Select "Search".

The list of telephones detected is

displayed.

Activate the Bluetooth function on the

telephone and ensure that it is "visible

to all" (telephone configuration).

If the pairing procedure fails, it is recommended

that you deactivate and then reactivate the

"Bluetooth" function in your telephone.

Select one or more profiles.

Procedure from the telephone

Select the system name in the list of

devices detected.

Press "Confirm".

Select the name of the chosen

telephone in the list.

In the system, accept the connection request

from the telephone.

To complete the pairing, whichever

procedure used (from the telephone or

from the system), ensure that the code

is the same in the system and in the

telephone.

Depending on the type of telephone,

you may be asked to accept or not

the transfer of your contacts and

messages.

396

Audio and Telematics

Automatic reconnection

To modify the connection profile:

The ability of the system to connect with

just one profile depends on the telephone.

All three profiles may connect by default.

on return to the vehicle, if the last

telephone connected is present again,

it is automatically recognised and

within about 30 seconds of switching

on the ignition, the connection is

established without any action on your

part (Bluetooth activated).

Press Telephone to display the

primary page.

Press the "OPTIONS" button to go to

the secondary page.

1

The services available depend on

the network, the SIM card and the

compatibility of the Bluetooth devices

used. Check in your telephone's

manual and with your service provider

for the services available to you.

Select "Bluetooth connection" to

display the list of paired devices.

Press the "details" button.

Select one or more profiles.

The profiles compatible with the system

are HFP, oPP, PBAP, A2DP, AVRCP,

MAP and PAN.

Press on "Confirm".

go to the brand's website for more information

(compatibility, additional help, ...).

.

397

Audio and Telematics

Managing paired telephones

Deleting a telephone

Receiving a call

Select the basket at top right of the

screen to display a basket alongside

the telephone chosen.

An incoming call is announced by a ring and a

superimposed display in the screen.

This function allows the connection or

disconnection of a peripheral device as

well as the deletion of a pairing.

Make a short press on the steering

mounted TEL button to accept an

incoming call.

Press the basket alongside the

telephone chosen to delete it.

Press Telephone to display the

primary page.

And

Press the "OPTIONS" button to go to

the secondary page.

Make a long press

1

on the steering mounted TEL button

to reject the call.

Select "Bluetooth connection" to

display the list of paired peripheral

devices.

or

Press on the name of the telephone

chosen in the list to disconnect it.

Press again to connect it.

Select "End call".

398

Audio and Telematics

Making a call

Calling a contact

Calling a recently used number

Press Telephone to display the

primary page.

using the telephone is not

recommended while driving.

Park the vehicle.

Make the call using the steering

mounted controls.

Press Telephone to display the

primary page.

or make a long press

or

Make a long press

on the steering mounted TEL button.

Select "Contact".

on the steering mounted button.

Calling a new number

Press Telephone to display the

primary page.

2

Select "Calls".

Select the desired contact from the list offered.

enter the phone number using the

digital keypad.

3

Select "Call".

Select the desired contact from the list offered.

Press "Call" to start the call.

It is always possible to make a call

directly from the telephone; as a safety

measure, first park the vehicle.

.

399

Audio and Telematics

Managing contacts / entries

Managing messages

Press Telephone to display the

primary page.

Press Telephone to display the

primary page.

The access to "Messages" depends on

the compatibility of the smartphone and

the integral system.

Depending on the smartphone, access

to your messages or email may be

slow.

Select "Contact".

Press the "OPTIONS" button to go to

the secondary page.

2

1

Select "Create" to add a new contact.

Select "Messages" to display the list

of messages.

The services available depend on

the network, the SIM card and the

compatibility of the Bluetooth devices

used.

Check in the manual for your telephone

and with your service provider for the

services available to you.

Select the "All" or "Received" or

"Sent" tab.

In the "Telephone" tab, enter the

telephone numbers for the contact.

12

Select the detail of the message

chosen in one of the lists

In the "Address" tab, enter the

addresses for the contact.

13

Press "Answer" to send a quick

message stored in the system.

In the "Email" tab, enter the email

addresses for the contact.

14

Press "Call" to start the call.

The "Email" function allows email

addresses to be entered for a contact,

but the system is not able to send

emails.

Press "Play" to hear the message.

400

Audio and Telematics

Managing quick messages

Managing email

Press Telephone to display the

primary page.

Press this button to "Modify" the new

quick message(s) created.

Press Telephone to display the

primary page.

Press on the "OPTIONS" button to

Press the "OPTIONS" button to go to

The "Modify" function does not apply

to quick messages already present in

the system.

go to the secondary page.

the secondary page.

1

Select "Messages" to display the list

Select "Email" to display the list of

of messages.

messages.

Select the "Delayed" or "My arrival"

or "Not available" or "Other" tab

with the possibility of creating new

messages.

Select the "Received" or "Sent" or

"Not read" tab.

Select the email chosen in the list.

Press "Create" to write a new

Press "Play" to hear the email.

message.

Select the message chosen in one of

the lists.

Access to "Email" depends on the

compatibility of the smartphone and the

integral system.

Press "Transfer" to select the

addressee(s).

Press "Play" to play the message.

.

401

Audio and Telematics

Settings

Level 1

Level 2

Audio settings

3

4

5

6

7

3

4

5

6

7

23 °C

12:13

Audio settings

1

2

3

4

5

6

7

402

Audio and Telematics

Level 1

Level 2

Comments

Ambience

Distribution

Sound

Select the sound ambience.

3

4

Adjust the volume or activate volume linked to

speed.

Settings

5

6

7

Audio settings

Voice

Adjust the voice volume.

Adjust the ringtone volume.

Save the settings.

Ringtone

Confirm

Settings

Function allowing the display to be switched off.

Pressing the screen reactivates it.

Turn off screen

Settings

Activate the profile selected.

Profile (1, 2, 3)

2

.

403

Audio and Telematics

Level 1

Level 2

Level 3

Screen configuration

1

8

9

8

9

Settings and tools

System settings

Information

10

11

12

Languages

13 14 15 16

404

Audio and Telematics

Level 1

Settings

Level 2

Animation

Level 3

Comments

Activate or deactivate settings.

Adjust the level of brightness.

Save the settings.

8

9

Secondary page

1

Brightness

Confirm

Screen

configuration

Distance and fuel

consumption

Set the units used for distance, fuel consumption

and temperature.

Units

10

11

12

Temperature

Reinitialize

Settings

Factory settings

System info

Return to the factory settings.

Secondary page

1

View the versions of the different modules

(system, mapping, risk areas) installed in the

system as well as the updates available.

System

settings

View

Confirm

All

Save the settings.

13

14

15

16

Europe

Asia

Settings

Secondary page

Languages

Select the language then confirm.

1

America

Confirm

Having selected the language, save the setting.

.

405

Audio and Telematics

Level 1

Level 2

Level 3

Setting the time-date

1

17

18

Settings and tools

Setting of the profiles

19 20 21 22

406

Audio and Telematics

Level 1

Level 2

Level 3

Comments

Date

Time

enter the date and select the date format.

17

18

Date format:

Time

Settings

Set the time.

Secondary page

1

Time Zone

Time format:

Define the time zone.

Setting

the time-date

Select the time format: 12h / 24h.

Activate or deactivate synchronisation with gPS.

Save the settings.

Synchronisation with

gPS (uTC):

Confirm

Profile 1

19

20

Settings

Profile 2

enter settings for the profiles.

Secondary page

1

Profile 3

21

22

Setting

of the profiles

Common profile

Confirm

Save the settings.

.

407

Audio and Telematics

Audio settings

Profile settings

Press Settings to display the primary

page.

The sound distribution (or spatialisation

processing that allows the quality of the

sound to be adapted according to the

number of passengers in the vehicle.

Available only with the 6-speaker

configuration.

As a safety measure and because it

requires the sustained attention of the

driver, changes to settings must only be

done with the vehicle stationary.

Select "Audio settings".

Select "Ambience"

"Position"

Press Settings to display the primary

page.

3

4

5

6

7

The audio Ambience settings

(6 ambiences available) as well as the

Bass, Medium and Treble settings

are different and independent for each

sound source.

or

Press the "OPTIONS" button to go to

the secondary page.

1

Select "Setting of the profiles".

Select "Profile 1", "Profile 2",

or

Activate or Deactivate "Loudness".

"Sound"

"Voice"

The settings for "Position" (All

passengers, Driver and Front only) are

common to all sources.

"Profile 3" or "Common profile".

19

Activate or Deactivate "Touch tones",

"Volume linked to speed" and

"Auxiliary input".

Press this button to enter a name for

the profile using the virtual keypad

"Ringtone".

Press "Confirm".

Staging optimises the distribution of

sound in the passenger compartment.

Press "Confirm" to save the settings.

408

Audio and Telematics

Press this button to add a photograph

to the profile.

Press this button to initialise the

profile selected.

Select a "Profile" (1 or 2 or 3) to

associate the "Audio settings" with it.

2

Select "Audio settings".

Insert a uSB memory stick containing

the photograph in the uSB port.

Select the photograph.

Initialisation of the profile selected

activates the english language by default.

Select "Ambience".

"Distribution".

Press "Confirm" to accept the

transfer of the photograph.

3

4

5

6

7

or

Press "Confirm" again to save the

settings.

or

"Sound".

"Voice".

The location for the photograph is

square; the system deforms the original

photograph if in another format.

"Ringtone".

Press "Confirm" to save the settings.

.

409

Audio and Telematics

Modifying system settings

Select the language

Press Settings to display the primary

page.

Press the "OPTIONS" button to go to

the secondary page.

1

Select "System settings".

Select "Languages" to change the

Select "Screen configuration".

language.

Select "Units" to change the units

for distance, fuel consumption and

temperature.

Select "Animation".

10

11

8

Setting the date

Select "Factory settings" to return

to the initial settings.

Activate or deactivatre "Automatic

scrolling".

Press Settings to display the primary

page.

Select "Brightness".

Returning the system to factory settings

activates the english language by

default.

Press the "OPTIONS" button to go to

the secondary page.

9

1

Adjust the brightness of the screen.

Select "Setting the time-date".

Select "System info" to display the

versions of the different modules

installed in the system.

12

410

Audio and Telematics

Select "Date".

Setting the time

17

Press Settings to display the primary

page.

Press "Confirm".

Press this button to define the date.

Press "Confirm".

Press the "OPTIONS" button to go to

the secondary page.

The system does not automatically

manage the change between winter

and summer time (depending on

country).

1

Select "Setting the time-date".

Select "Time".

Select the display format of the date.

18

Press this button to adjust the time

using the virtual keypad.

Adjustment of the time and date is only

available if synchronisation with gPS is

deactivated.

The change between winter and

summer time is done by changing the

time zone.

Press "Confirm".

Press this button to define the time

zone.

Select the display format for the

time (12h / 24h).

Activate or deactivate

synchronisation with gPS (uTC).

.

411

Audio and Telematics

Frequently asked questions

The following table groups together the answers to the most frequently asked questions concerning your audio system.

Navigation

QUESTION

ANSWER

SOLUTION

The route calculation is

not successful.

The route settings may conflict with the current location (exclusion

of toll roads on a toll motorway).

Check the route settings in the "Navigation"

menu.

The PoIs do not appear.

The PoIs have not been selected.

Select the PoIs in the list of PoIs.

The audible warning of

"Danger areas" does not

work.

The audible warning is not active.

Activate audible warnings (without the possibility

of adjusting the volume) in the "Navigation"

menu.

The system does not

suggest a detour around

an incident on the route.

The guidance criteria do not take account of TMC messages.

Select a setting for the "Traffic info" function

in the list of route settings (Without, Manual or

Automatic).

I receive a "Danger area"

alert which is not on my

route.

other than guidance, the system announces all "Danger areas"

positioned in a cone located in front of the vehicle. It may provide

an alert for "Danger areas" located on nearby or parallel roads.

Zoom in on the map to view the exact position of the

"Danger areas". Select "on the route" to no longer

receive alerts other than navigation instructions or to

reduce the time for the announcement.

412

Audio and Telematics

QUESTION

ANSWER

SOLUTION

Certain traffic jams along

on starting, it is several minutes before the system starts to receive Wait until the traffic information is being received

the route are not indicated traffic information.

in real time.

correctly (display of the traffic information icons

on the map).

In certain countries, only major routes (motorways...) are listed for

the traffic information.

This phenomenon is normal. The system is

dependent on the traffic information available.

The altitude is not

displayed.

on starting, the initialisation of the gPS may take up to 3 minutes to Wait until the system has started up completely

receive more than 4 satellites correctly.

so that there is gPS coverage by at least

4 satellites.

Depending on the geographical environment (tunnel...) or the

weather, the conditions of reception of the gPS signal may vary.

This phenomenon is normal. The system

is dependent on the gPS signal reception

conditions.

.

413

Audio and Telematics

Radio

QUESTION

ANSWER

SOLUTION

The quality of reception of The vehicle is too far from the transmitter used by the station

Activate the "RDS" function by means of the

short-cut menu to enable the system to check

whether there is a more powerful transmitter in

the geographical area.

the radio station listened

to gradually deteriorates

or the stored stations do

not function (no sound,

87.5 Mhz is displayed...).

listened to or there is no transmitter in the geographical area

through which the vehicle is travelling.

The environment (hills, buildings, tunnels, basement car parks...)

block reception, including in RDS mode.

This phenomenon is normal and does not

indicate a fault with the audio system.

The aerial is absent or has been damaged (for example when going Have the aerial checked by a franchised dealer.

through a car wash or into an underground car park).

I cannot find some radio

stations in the list of

stations received.

The station is not received or its name has changed in the list.

Press on the "update list" button in the "Radio

stations" secondary menu.

Some radio stations send other information in place of their name

(the title of the song for example).

The system interprets this information as the name of the station.

The name of the radio

station changes.

414

Audio and Telematics

Media

QUESTION

ANSWER

SOLUTION

Playback of my uSB

memory stick starts only

after a very long wait

(around 2 to 3 minutes).

Some files supplied with the memory stick may greatly slow down

access to reading the memory stick (multiplication by 10 of the

catalogue time).

Delete the files supplied with the memory stick

and limit the number of sub-folders in the file

structure on the memory stick.

Some characters in the

media information are not

displayed correctly while

playing.

The audio system does not display some types of characters.

The peripheral device connected does not support automatic play.

The Bluetooth profile does not allow the transfer of this information.

use standard characters to name tracks and

folders.

Playing of streaming files

does not start.

Start the playback from the device.

The names of tracks and

the track length are not

displayed on the screen

when streaming audio.

.

415

Audio and Telematics

Telephone

QUESTION

ANSWER

SOLUTION

I cannot connect my

Bluetooth telephone.

The telephone's Bluetooth function may be switched off or the

telephone may not be visible.

Check that your telephone's Bluetooth function is

switched on.

Check in the telephone settings that it is "visible

to all".

The Bluetooth telephone is not compatible with the system.

The volume depends both on the system and on the telephone.

You can check the compatibility of your

telephone at the brand's website (services).

The volume of the

telephone connected

in Bluetooth mode is

inaudible.

Increase the volume of the audio system, to

maximum if required, and increase the volume of

the telephone if necessary.

The ambient noise level has an influence on the quality of

telephone communication.

Reduce the ambient noise level (close the

windows, reduce the booster fan speed, slow

down, ...).

Some contacts are

duplicated in the list.

The options for synchronizing contacts are synchronizing the

contacts on the SIM card, the contacts on the telephone, or both.

When both synchronizations are selected, some contacts may be

duplicated.

Select "Display SIM card contacts" or "Display

telephone contacts".

Contacts are not shown in Some telephones offer display options. Depending on the settings

Modify the display setting in the telephone

directory.

alphabetical order.

chosen, contacts can be transferred in a specific order.

The system does not

The Bluetooth mode does not permit sending SMS text messages

receive SMS text messages. to the system.

416

Audio and Telematics

Settings

QUESTION

ANSWER

SOLUTION

In changing the setting

of treble and bass the

equalizer setting is

deselected.

The selection of an equalizer setting imposes the settings for treble Modify the treble and bass or equalizer settings

and bass and vice-versa.

to obtain the desired musical ambience.

In changing the equalizer

setting, treble and bass

return to zero.

When changing the

balance settings, the

distribution setting is

deselected.

The selection of a distribution setting imposes the balance settings

and vice-versa.

Modify the balance or distribution settings to

obtain the desired musical ambience.

When changing a

distribution setting,

the balance setting is

deselected.

.

417

Audio and Telematics

QUESTION

ANSWER

SOLUTION

There is a difference in

For optimum sound quality, the audio settings for Loudness,

Check that the audio settings for Loudness,

sound quality between the Ambience, Treble, Bass and Volume can be adapted to the different Ambience, Treble, Bass and Volume are adapted

different audio sources.

sound sources, which may result in audible differences when

changing source.

to the sources listened to. Adjust the Balance,

Treble and Bass to the middle position, select the

"None" musical ambience and set the loudness

correction to the "Active" position in CD mode or

to the "Inactive" position in radio mode.

With the engine off, the

When the engine is switched off, the system's operating time

Start the vehicle's engine to increase the battery

charge.

system switches off after a depends on the state of charge of the battery.

few minutes of use. The switch-off is normal: the system switches to economy mode

and switches off to prevent discharging of the vehicle's battery.

418

Audio and Telematics (Nav) for Your Peugeot Traveller Van First Generation (2016-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals