Get Instruments Guide for Peugeot Traveller Van First Generation (2016-2026)

Instruments

1

LCD text instrument panel

Dials and screens

1. Analogue speedometer (mph or km/h).

Control buttons

A. Reset the service indicator.

6. gear shift indicator.

2. Fuel gauge.

gear with an automatic or electronic

gearbox.

7. Service indicator, then total distance

recorder (miles or km), trip recorder (miles

or km), display of messages, ...

8. Rev counter (x 1 000 rpm or tr/min).

Temporarily recall information on:

3. engine coolant temperature gauge.

4. Cruise control or speed limiter settings.

5. Digital speedometer (mph or km/h).

-

servicing,

remaining driving range with the

emissions fluid (AdBlue^®).

B. Main lighting dimmer.

C. Reset the trip recorder.

13

Instruments

Matrix instrument panel

Dials and screens

1. Analogue speedometer (mph or km/h).

Control buttons

A. Reset the service indicator.

6. Display area: alert or state of function

2. Fuel gauge.

messages, trip computer, digital

speedometer (mph or km/h), ...

7. Service indicator, then total distance

recorder (miles or km).

These functions are displayed in turn when

the ignition is switched on.

8. Trip recorder (miles or km).

9. Rev counter (x 1 000 rpm or tr/min).

Display the alert log.

Recall information on:

3. engine coolant temperature gauge.

4. Cruise control or speed limiter settings.

5. gear shift indicator.

-

servicing,

remaining driving range with the

emissions fluid (AdBlue^®).

gear with an automatic or electronic

gearbox.

B. Main lighting dimmer.

C. Reset the trip recorder.

14

Instruments

Warning lamps

Operation indicator lamps

Indicator and warning lamps

Visual indicators informing the driver that

a system is in operation or is switched off

(indicator lamp), or has a fault (warning lamp).

1

When the engine is running or the vehicle is

being driven, illumination of one of the following

warning lamps indicates a fault which requires

action on the part of the driver.

If one of the following indicator lamps comes on

in the instrument panel and/or instrument panel

screen, this confirms that the corresponding

system has come into operation.

Any fault resulting in the illumination of a

warning lamp must be investigated further

using the associated message.

If you encounter any problems, contact a

PeugeoT dealer or a qualified workshop.

When the ignition is switched on

Certain warning lamps come on for a few

seconds when the vehicle's ignition is

switched on.

When the engine is started, these same

warning lamps should go off.

If they remain on, before moving off, refer to the

information on the warning lamp concerned.

Associated warnings

Certain warning lamps may come on in one of

two modes: fixed (continuous) or flashing.

only by relating the type of illumination to the

operation of the vehicle can it be determined

whether the situation is normal or a fault has

occurred. In the event of a fault, the illumination

of the warning lamp may be accompanied by

an audible signal and/or a message.

Deactivation indicator lamps

If one of the following indicator lamps comes

on, this confirms that the corresponding system

has been switched off intentionally.

This is may be accompanied by an audible

signal and the display of a message.

15

Instruments

Warning / indicator lamp

STOP

State

Cause

Action / Observations

fixed, associated with

another warning lamp, related to a serious fault detected

accompanied by an

audible signal and a

message.

Illumination of this warning lamp is

You must stop as soon as it is safe to do so.

Park, switch off the ignition and call a PeugeoT

dealer or a qualified workshop.

with the engine, the braking system,

the power steering, etc., or a major

electrical fault.

Parking brake

fixed.

The parking brake is applied or not

properly released.

Release the parking brake to switch off the warning

lamp, keeping your foot on the brake pedal.

observe the safety recommendations.

For more information on the Parking brake, refer to

the corresponding section.

Braking

The brake fluid level has dropped

significantly.

You must stop as soon as it is safe to do so.

Top-up with brake fluid listed by PeugeoT.

If the problem persists, have the system checked by a

PeugeoT dealer or a qualified workshop.

fixed, associated

with the ABS warning

lamp.

The electronic brake force distribution You must stop as soon as it is safe to do so.

(eBFD) system has a fault.

Have it checked by a PeugeoT dealer or a qualified

+

workshop.

16

Instruments

Warning / indicator lamp

State

Cause

Action / Observations

Pull the strap then insert the tongue in the buckle.

1

Seat belt(s)

not fastened /

unfastened

fixed

A seat belt has not been fastened or

has been unfastened.

or flashing

accompanied by an

audible signal.

Battery charge*

fixed.

The battery charging circuit has a

fault (dirty or loose terminals, slack or started.

cut alternator belt, ...).

The warning lamp should go off when the engine is

If it does not go off, contact a PeugeoT dealer or a

qualified workshop.

Engine oil

pressure

There is a fault with the engine

lubrication system.

You must stop as soon it is safe to do so.

Park, switch off the ignition and contact a PeugeoT

dealer or a qualified workshop.

Maximum

coolant

temperature

fixed with the needle

in the red zone.

The temperature of the cooling

system is too high.

You must stop as soon as it is safe to do so.

Wait until the engine has cooled down before topping-

up the level, if necessary.

If the problem persists, contact a PeugeoT dealer or

a qualified workshop.

* Depending on the country of sale.

17

Instruments

Warning / indicator lamp

State

Cause

Action / Observations

Door(s)

open

fixed, associated with

a message identifying rear door or tailgate) is still open.

the door, if the speed

is below 6 mph

(10 km/h).

A front, side or rear door (side-hinged Close the door in question.

If your vehicle has side-hinged rear doors and the

right hand door is still open, this will not be signalled

by this warning lamp.

If fitted to your vehicle, the tailgate

screen is still open.

fixed, associated with

a message identifying

the door, together with

an audible signal if the

speed is above 6 mph

(10 km/h).

Low fuel level

fixed, with the needle

in the red zone.

When it first comes on there remains You must refuel as soon as possible to avoid running

less than 8 litres of fuel in the tank.

out of fuel.

This warning lamp will come on every time the ignition

is switched on, until a sufficient addition of fuel is

made.

Fuel tank capacity: approximately 69 litres.

Never continue to drive until you run out of fuel as

this could damage the emission control and injection

systems.

18

Instruments

Warning / indicator lamp

State

Cause

Action / Observations

1

Engine

auto-diagnosis

fixed, associated with

the SToP warning

lamp.

A major engine fault has been

detected.

You must stop as soon as it is safe to do so.

Park, switch off the ignition and contact a PeugeoT

dealer or a qualified workshop.

system

+

Engine

auto-diagnosis

system

fixed.

The emission control system has a

fault.

The warning lamp should go off when the engine is started.

If it does not go off, contact a PeugeoT dealer or

qualified workshop without delay.

flashing.

The engine management system has Risk of destruction of the catalytic converter.

a fault.

Have it checked by a PeugeoT dealer or a qualified

workshop.

fixed, associated with

A minor engine fault has been

Have it checked by a PeugeoT dealer or a qualified

the SeRVICe warning detected.

workshop.

lamp.

+

Diesel engine

pre-heating

fixed.

The ignition switch is at

Wait until the warning lamp goes off before starting.

once it goes off, starting is immediate, on condition that:

the 2^ndposition (igntion on).

-

the clutch pedal is pressed fully down with a manual

gearbox,

or

The "START/STOP" button has been

pressed.

-

pressure is maintained on the brake pedal with an

automatic or electronic gearbox.

The period of illumination of the warning lamp is

determined by the ambient conditions (up to about thirty

seconds in extreme conditions).

If the engine does not start, switch the ignition off and

then on, wait until the warning lamp goes off again, then

start the engine.

19

Instruments

Warning / indicator lamp

Under-inflation

State

Cause

Action / Observations

fixed, accompanied by The pressure in one or more tyres is

an audible signal and

a message.

Check the tyre pressures as soon as possible.

This check should preferably be carried out when the

tyres are cold.

too low.

You must reinitialise the system after the adjustment

of one or more tyre pressures and after changing one

or more wheels.

For more information on Under-inflation detection,

refer to the corresponding section.

+

flashing then fixed,

accompanied by the

Service warning lamp.

The system has a fault: the tyre

pressures are no longer monitored.

Check the tyre pressures as soon as possible.

Have the system checked by a PeugeoT dealer or a

qualified workshop.

Foot on the

brake pedal

fixed.

The brake pedal must be pressed.

With an automatic or electronic gearbox, press the

brake pedal, engine running, before releasing the

parking brake, to release the selector lever and come

out of position P or N.

If you wish to release the parking brake without

pressing the brake pedal, this warning lamp will

remain on.

Foot on the

clutch

fixed.

In the SToP mode of Stop & Start,

the change to START mode is denied declutch fully to allow the change to engine START

If your vehicle has a manual gearbox, you must

because the clutch pedal is not fully

down.

mode.

20

Instruments

Warning / indicator lamp

State

Cause

Action / Observations

1

Anti-lock

Braking System

(ABS)

fixed.

The anti-lock braking system has a

fault.

The vehicle retains conventional braking.

Drive carefully at reduced speed and contact a

PeugeoT dealer or a qualified workshop without

delay.

Collision Risk

Alert / Active

Safety Brake

flashing.

The system is operating.

The system has a fault.

The system brakes briefly so as to reduce the speed

of collision with the vehicle ahead.

fixed, accompanied

by a message and an

audible signal

Have the system checked by a PeugeoT dealer or a

qualified workshop.

fixed, accompanied by The system has been deactivated

For more information on the Collision Risk

Alert / Active Safety Brake system, refer to the

corresponding section.

a message.

(via the menu).

Particle filter

(Diesel)

fixed, accompanied

by an audible signal

message on the risk

of blockage of the

particle filter.

This indicates that the particle filter is As soon as driving conditions allow, regenerate the

starting to become saturated.

filter by driving at a speed of at least 35 mph (60 km/h)

until the warning lamp goes off.

fixed, accompanied

by an audible signal

and and a message

that the particle filter

additive level is too

low.

This indicates the low level of the

additive reservoir.

Have the reservoir topped-up as soon as possible by

a PeugeoT dealer or a qualified workshop.

21

Instruments

Warning / indicator lamp

Airbags

State

Cause

Action / Observations

on temporarily.

This warning lamp comes on for a

few seconds when you turn on the

ignition, then goes off.

This warning lamp should go off when the engine is

started.

If it does not go off, contact a PeugeoT dealer or a

qualified workshop.

fixed.

one of the airbag or seat belt

Have them checked by a PeugeoT dealer or a

pretensioner systems has a fault.

qualified workshop.

Passenger's

front airbag

fixed in the seat belt

and front passenger's

airbag warning lamps

display.

The control switch, located at the

passenger's end of the dashboard, is the passenger's front airbag; in this case, you must

set to the "OFF" position.

The passenger's front airbag is

deactivated.

Turn the control switch to the "ON" position to activate

not install a child seat in the rearward facing position

on this seat.

You can install a rearward facing

child seat, unless there is a fault with

the airbags (airbag warning lamp on).

Passenger's

front airbag

fixed.

The control switch, located at the

passenger's end of the dashboard, is deactivate the passenger's front airbag.

Turn the control switch to the "OFF" position to

at the "ON" position.

The passenger's front airbag is

activated.

You can install a rearward facing child seat, unless

there is a fault with the airbags (airbag warning

lamp on).

In this case, do not install a rearward

facing child seat on the front

passenger seat.

22

Instruments

Warning / indicator lamp

State

Cause

Action / Observations

1

Dynamic

stability control

(DSC/ASR)

fixed.

The button is pressed and the

indicator lamp comes on.

The DSC/ASR is deactivated.

DSC: dynamic stability control.

ASR: anti-slip regulation.

Press the button to activate the DSC/ASR. Its

indicator lamp goes off.

The DSC/ASR system is activated automatically when

the vehicle is started.

If deactivated, the system is reactivated automatically

from around 30 mph (50 km/h).

For more information on the Electronic stability

programme (ESC) and in particular, DSC/ASR, refer

to the corresponding section.

Dynamic

stability control

(DSC/ASR)

flashing.

The DSC/ASR regulation is

operating.

The system optimises traction and improves the

directional stability of the vehicle in the event of loss of

grip or trajectory.

fixed.

The DSC/ASR system has a fault.

The power steering has a fault.

Have the system checked by a PeugeoT dealer or a

qualified workshop.

Power

steering

Drive carefully at reduced speed.

Have it checked by a PeugeoT dealer or a qualified

workshop.

23

Instruments

Warning / indicator lamp

AdBlue^®

State

Cause

Action / Observations

fixed, on switching

The remaining driving range is

between 350 miles (600 km) and

1500 miles (2400 km).

Have the AdBlue^®tank topped-up as soon as

possible: go to a PeugeoT dealer or a qualified

workshop, or carry out this operation yourself.

(BlueHDi Diesel) on the ignition,

accompanied by an

audible signal and a

message indicating

the remaining driving

range.

flashing, accompanied The remaining driving range is

You must top-up the AdBlue^®tank to avoid a

breakdown: go to a PeugeoT dealer or a qualified

workshop, or carry out this operation yourself.

by an audible signal

and a message

indicating the

remaining driving

range.

between 0 and 350 miles (600 km).

flashing, accompanied The AdBlue^®tank is empty: the

To be able to start the engine, you must top-up the

AdBlue^®tank: go to a PeugeoT dealer or a qualified

workshop, or carry out this operation yourself.

It is essential to add at least 3.8 litres of AdBlue^®to

the fluid tank.

by an audible signal

and a message

starting inhibition system required

by legislation prevents starting of the

indicating that starting engine.

is prevented.

For topping-up the AdBlue^®fluid or for more information on AdBlue^®, refer to the corresponding section.

24

Instruments

Warning / indicator lamp

State

Cause

Action / Observations

1

SCR emissions

control system

fixed, on switching

on the ignition,

A fault with the SCR emissions

control system has been detected.

This alert disappears once the exhaust emissions

return to normal levels.

+

(BlueHDi Diesel) associated with the

SeRVICe and engine

diagnostic warning

lamps, accompanied

by an audible signal

and a message.

flashing, on switching

on the ignition,

After confirmation of the fault with the Contact a PeugeoT dealer or a qualified workshop

emissions control system, you can

drive for up to 650 miles (1 100 km)

before the engine starting inhibition

system is triggered.

without delay, to avoid a breakdown.

associated with the

SeRVICe and engine

diagnostic warning

lamps, accompanied by

an audible signal and

a message indicating

the remaining driving

range.

flashing, on switching

on the ignition,

You have exceeded the authorised

driving limit following confirmation

of a fault with the emissions control

system: the engine starting inhibition

system prevents starting of the

engine.

To be able to start the engine, you must call on a

PeugeoT dealer or a qualified workshop.

associated with the

SeRVICe and engine

diagnostic warning

lamps, accompanied

by an audible signal

and a message.

25

Instruments

Warning / indicator lamp

Service

State

Cause

Action / Observations

on temporarily.

A minor fault has occurred for which

there is no specific warning lamp.

Identify the fault by means of the associated message,

for example:

-

low engine oil level,

low screenwash/headlamp wash fluid level,

discharged remote control battery,

low tyre pressures,

saturation of the particle filter (FAP) on Diesel

vehicles.

-

...

For more information on Checks and in particular the

particle filter, refer to the corresponding section.

For any other faults, contact a PeugeoT dealer or a

qualified workshop.

fixed.

A major fault has occurred for which

there is no specific warning lamp.

Identify the fault by reading the message and contact

a PeugeoT dealer or a qualified workshop.

fixed, associated with

The servicing interval has been

only on BlueHDi Diesel versions.

flashing and then fixed exceeded.

display of the service

spanner.

Your vehicle must be serviced as soon as possible.

+

Rear foglamps

fixed.

The rear foglamps are on.

Turn the ring on the stalk rearward to switch off the

rear foglamps.

26

Instruments

Warning / indicator lamp

State

Cause

Action / Observations

1

Automatic

wiping

fixed.

The wiper control has been pushed

down.

Automatic front wiping is activated.

To deactivate automatic wiping, operate the control

stalk downwards or put the stalk into another position.

Automatic

headlamp

dipping

The lighting control stalk is in the

"AUTO" position, and the function

has been activated.

The camera, located at the top of the windscreen,

manages the operation of main beam, depending on

the ambient lighting and driving conditions.

The main beam headlamps come

on if the exterior lighting and driving

conditions permit.

For more information on Automatic headlamp

dipping, refer to the corresponding section.

Stop & Start

fixed.

When the vehicle stops (red lights,

The warning lamp goes off and the engine restarts

traffic jams, ...) the Stop & Start system automatically in START mode, as soon as you want to

has put the engine into SToP mode.

move off.

flashes for a few

seconds, then goes

off.

SToP mode is temporarily

unavailable,

or

For more information on Stop & Start, refer to the

corresponding section.

START mode is invoked

automatically.

Blind spot

monitoring

system

fixed.

The blind spot monitoring system has For more information on the Blind spot monitoring

been activated. system, refer to the corresponding section.

27

Instruments

Warning / indicator lamp

State

Cause

Action / Observations

Lane departure

warning system

fixed.

The lane departure warning system

has been activated.

The lane departure warning system is on.

For more information on the Lane departure warning

system, refer to the corresponding section.

Front

foglamps

fixed.

The front foglamps are switched on

using the ring on the lighting control

stalk.

Turn the ring on the lighting control stalk rearward

once to switch off the front foglamps.

Sidelamps

The lighting stalk is in the

"Sidelamps" position.

Left-hand

direction

indicator

flashing with buzzer.

fixed.

The lighting stalk has been pushed

down.

Right-hand

direction

indicator

The lighting stalk has been

pushed up.

Dipped beam

headlamps

The lighting stalk is in the "Dipped

beam headlamps" position.

Main beam

headlamps

fixed.

The lighting stalk has been pulled

towards you.

Pull the stalk to return to dipped beam headlamps.

For more information on the Lighting control stalk, refer to the corresponding section.

28

Instruments

Engine coolant temperature

Service indicator

System which informs the driver when the

next service is due, in accordance with the

manufacturer's servicing schedule.

1

Checking the level

After driving for a few minutes, the temperature

and pressure in the cooling system increase.

To top-up the level:

F

wait at least one hour for the engine to

cool,

unscrew the cap two turns to allow the

pressure to drop,

when the pressure has dropped, remove

the cap,

top-up the level to the "MAX" mark.

The point at which the next service is due is

calculated from the last indicator zero reset,

depending on the distance travelled and the

time elapsed since the last service.

With the engine running, when the needle is:

-

in zone A, the temperature of the engine

coolant is correct,

For BlueHDi Diesel versions, the degree of

deterioration of the engine oil is also taken into

account (depending on the country of sale).

-

in zone B, the temperature of the engine

coolant is too high; the maximum

temperature and the central STOP warning

lamps come on, accompanied by an

audible signal and a warning message in

the touch screen.

You MUST stop as soon as it is safe to do so.

Wait a few minutes before switching off the

engine.

Contact a PeugeoT dealer or a qualified

workshop.

Be aware of the risk of burns when

topping-up the cooling system. Do not

fill above the maximum level (indicated

on the header tank).

29

Instruments

More than 1 800 miles (3 000 km)

remain before the next service is due

Less than 600 miles (1 000 km)

remain before the next service is due

Service overdue

When the ignition is switched on, no service

information appears in the screen.

Example: 560 miles (900 km) remain before

the next service is due.

For 5 seconds after the ignition is switched on,

the screen indicates:

For 5 seconds after the ignition is switched on,

the spanner flashes to indicate that the service

must be carried out as soon as possible.

Example: the service is overdue by 180 miles

(300 km).

Between 600 miles (1 000 km)

and 1 800 miles (3 000 km) remain

before the next service is due

For 5 seconds after the ignition is switched on, the

spanner symbolising the service operations comes

on. The distance recorder display line indicates the

distance remaining before the next service is due.

Example: 1 700 miles (2 800 km) remain before

the next service is due.

For 5 seconds after the ignition is switched on,

the screen indicates:

5 seconds after the ignition is switched on,

the distance recorder resumes its normal

operation. The spanner remains on to

indicate that a service must be carried out

soon.

For 5 seconds after the ignition is switched on, the

screen indicates:

5 seconds after the ignition is switched on,

the distance recorder resumes its normal

operation. The spanner remains on.

For BlueHDi Diesel versions, this alert may

also be accompanied by the fixed illumination

of the service warning lamp when the ignition

is on.

5 seconds after the ignition is switched on,

the spanner goes off; the distance recorder

resumes its normal operation. The screen then

indicates the total distance.

30

Instruments

Resetting the service indicator

The distance remaining may be

weighted by the time factor, depending

on the driving conditions.

If you have to disconnect the battery

1

following this operation, lock the vehicle

and wait at least five minutes for the

reset to be registered.

Therefore, the spanner may also come

on if you have exceeded the period

since the last service, indicated in the

manufacturer's service schedule.

For BlueHDi Diesel versions, the

spanner may also be brought on earlier

than expected, depending on the

degree of deterioration of the engine oil

(depending on the country of sale).

The rate of deterioration of the engine

oil depends on the driving conditions in

which the vehicle is used.

Retrieving the service

information

You can access the service information at any

time.

After each service, the service indicator must

be reset to zero.

If you have carried out the service on your

vehicle yourself, switch off the ignition:

F

Press this button.

F

Press and hold this button,

The service information is displayed for a

few seconds, then disappears.

F

Switch on the ignition; the distance

recorder display begins a countdown,

When the display indicates "=0", release

the button; the spanner disappears.

31

Instruments

Dipstick

Engine oil level

indicator

To locate the dipstick and the oil filler

cap for the Diesel engine, refer to the

corresponding section.

on versions fitted with an electric oil gauge,

information on the oil level is displayed in the

instrument panel for a few seconds when the

ignition is switched on, at the same time as the

service information.

Oil level incorrect

This is indicated by a message in the

instrument panel.

If the low oil level is confirmed by a check using

the dipstick, the level must be topped-up to

avoid damage to the engine.

There are 2 marks on the

dipstick:

The level read will only be correct if

the vehicle is on level ground and the

engine has been off for more than

30 minutes.

-

A = max; never exceed this

level,

-

B = min; top-up the level via

the oil filler, using the grade

of oil suited to your engine.

Oil level correct

Oil level indicator fault

This is indicated by a message in the

instrument panel.

This is indicated by a message in the

instrument panel. Contact a PeugeoT dealer

or a qualified workshop.

32

Instruments

In the event of the risk of non-starting related to a lack of AdBlue^®

AdBlue^®fluid range

indicators

once the AdBlue^®tank is on reserve or after

detection of a fault with the SCR emissions

control system, when the ignition is switched

on, an indicator displays an estimate of the

distance that can be covered, the range, before

engine starting is prevented.

1

Remaining range greater than 1 500 miles (2 400 km)

Remaining range between 350 and 1500 miles (600 and 2 400 km)

When switching on the ignition, there is no

automatic display of range in the instrument

panel.

When switching on the ignition, this warning

lamp comes on, accompanied by an

audible signal and the display of a message

(e.g.: "Top up emissions additive: Starting

prevented in 900 miles") indicating the

remaining range expressed in miles or

kilometres.

When driving, the message is displayed every

200 miles (300 km) until the fluid has been

topped-up.

In the event of simultaneous system fault and

low AdBlue^®level, the shortest range figure is

the one displayed.

Pressing this button will display the remaining

range.

You can access this information in the touch

screen, if your vehicle has one.

go to a PeugeoT dealer or a qualified

workshop to have the AdBlue^®topped-up.

You can also top-up the tank yourself.

F

Select the "Driving" menu.

Select "OPTIONS".

Then select "Diagnostic".

F

For more information on AdBlue^®and

the SCR system, and in particular on

topping-up the AdBlue^®, refer to the

corresponding section.

The engine start prevention system

required by regulations is activated

automatically once the AdBlue^®tank is

empty.

The range is then displayed temporarily.

Above 3 000 miles (5 000 km), the value is not

specified.

33

Instruments

Remaining range between 0 and 350 miles (0 and 600 km)

Breakdown related to a lack of AdBlue^®

When switching on the ignition, this

warning lamp flashes, accompanied

by an audible signal and the display

of the message "Top up emissions

When switching on the ignition, this warning

lamp flashes, accompanied by an audible

signal and the display of a message

(e.g. "Top up emissions additive: Starting

prevented in 350 miles") indicating the

remaining range expressed in miles or

kilometres.

additive: Starting prevented".

The AdBlue^®tank is empty: the system required

by regulations prevents engine starting.

When driving, the message is displayed every

30 seconds until the fluid has been topped-up.

go to a PeugeoT dealer or a qualified

workshop to have the AdBlue^®topped-up.

You can also top-up the tank yourself.

otherwise you will not be able to restart your

engine.

To be able to start the engine,

we recommend that you call on a

PeugeoT dealer or a qualified

workshop for the top-up required.

If you carry out the top-up yourself, it

is essential to add at least 3.8 litres of

AdBlue^®to the tank.

For more information on AdBlue^®and

the SCR system, and in particular on

topping-up the AdBlue^®, refer to the

corresponding section.

34

Instruments

In the event of a fault with the SCR emissions control system

1

A system that prevents engine starting is activated automatically from 650 miles (1 100 km) after confirmation of a fault with the SCR emissions

control system. Have the system checked by a PeugeoT dealer or a qualified workshop as soon as possible.

In the event of the detection

of a fault

During an authorised driving phase (between

650 miles and 0 miles) (1 100 km and 0 km)

Starting prevented

These warning lamps come on, accompanied

by an audible signal and the display of the

message "emissions fault".

The alert is triggered when driving when the

fault is detected for the first time, then when

switching on the ignition for subsequent

journeys, while the fault persists.

If a fault with the SCR system is confirmed

(after 30 miles (50 km) covered with the

permanent display of the message signalling

a fault), these warning lamps come on,

accompanied by an audible signal and the

display of a message (e.g.: "emissions fault:

Starting prevented in 150 miles") indicating

the remaining range expressed in miles or

kilometres.

While driving, the message is displayed every

30 seconds while the fault with the SCR system

persists.

The alert is repeated when switching on the

ignition.

every time the ignition is switched on, these

warning lamps come on, accompanied by an

audible signal and the display of the message

"emissions fault: Starting prevented".

You have exceeded the authorised

driving limit: the starting prevention

system inhibits engine starting.

To be able to start the engine, you must call on

a PeugeoT dealer or a qualified workshop.

If it is a temporary fault, the alert

disappears during the next journey,

after self-diagnosis of the SCR system.

You should go to a PeugeoT dealer or a

qualified workshop as soon as possible.

otherwise, you will not be able to restart your

engine.

35

Instruments

Distance recorders

The total and trip distances are displayed for

thirty seconds when the ignition is switched off,

when the driver's door is opened and when the

vehicle is locked or unlocked.

When travelling abroad, you may

have to change the units of distance:

the display of road speed must be in

the official units (miles or km) for the

country. The change of units is done via

the screen configuration menu, with the

vehicle stationary.

Total distance recorder

It measures the total distance travelled by the

vehicle since its first registration.

Trip distance recorder

It measures the distance travelled since it was

reset to zero by the driver.

F

With the ignition on, press this

button until zeros appear.

36

Instruments

You can also switch off the screen. To do this:

1

Lighting dimmer

This system allows the brightness of the instruments and controls to be adjusted to suit the ambient

light level.

F

Press on the Settings button.

Select Switch off screen.

At the instrument panel

With the touch screen

F

Press on the Settings button.

The screen goes off completely.

Press on the screen again (anywhere on its

surface) to activate it.

F

Select "OPTIONS".

F

Select "Screen configuration".

Select the "Brightness" tab.

F

With the exterior lighting on, press this

button to raise the level of brightness.

With the exterior lighting on, press this

button to lower the level of brightness.

F

Adjust the brightness by moving

the cursor.

As soon as the lighting reaches the required

level of brightness, release the button.

Press on "Confirm" to save and

quit.

37

Instruments

Trip computer

System that gives you information on the current journey (range, fuel consumption…).

-

The current information with:

● the range,

● the current fuel consumption,

● the Stop & Start time counter.

Trip "1" with:

● the average speed,

● the average fuel consumption,

● the distance travelled,

for the first trip.

Display of information

Depending on equipment, a 2^ndtrip is available.

F

or, depending on equipment, press the

thumbwheel on the steering wheel.

-

Trip "2" with:

● the average speed,

● the average fuel consumption,

● the distance travelled,

for the second trip.

Trips "1" and "2" are independent but their use

is identical.

For example, trip "1" can be used for daily

figures, and trip "2" for monthly figures.

F

Press the button on the end of the wiper

control stalk to display the different trip

computer tabs in turn.

38

Instruments

Trip reset

1

With LCD text instrument panel

F

When the desired trip is displayed, press

the reset button in the instrument panel for

more than two seconds.

F

or, depending on equipment, press the

thumbwheel on the steering wheel for

more than two seconds.

With LCD text or matrix

instrument panel

F

When the trip is displayed, press the button

on the end of the wiper control stalk.

39

Instruments

A few definitions

Range

(miles or km)

Current fuel

consumption

Distance travelled

(miles or km)

The distance which can still be

(mpg or l/100 km or km/l)

Calculated since the last trip reset.

travelled with the fuel remaining in

the tank (related to the average fuel

consumption over the last few miles

(kilometres) travelled).

Calculated over the last few seconds.

Stop & Start time

counter

This function is only displayed from

20 mph (30 km/h).

(minutes / seconds or hours /

minutes)

This value may vary following a change

in the style of driving or the relief,

resulting in a significant change in the

current fuel consumption.

If your vehicle is fitted with Stop & Start, a time

counter calculates the time spent in SToP

mode during a journey.

It resets to zero every time the ignition is

switched on.

Average fuel consumption

(mpg or l/100 km or km/l)

Calculated since the last trip reset.

When the range falls below 20 miles (30 km),

dashes are displayed. After filling with at least

8 litres of fuel, the range is recalculated and is

displayed when it exceeds 60 miles (100 km).

Average speed

(mph or km/h)

Calculated since the last trip reset.

If dashes are displayed continuously

while driving in place of the digits,

contact a PeugeoT dealer or a

qualified workshop.

40

Instruments

Menus

1

Touch screen

use the buttons on either side of the touch

screen for access to the menus, then press the

virtual buttons in the touch screen.

use this button to confirm.

use this button to quit.

Driving.

Settings.

Allows certain functions to be switched

on and off and their settings adjusted.

Allows configuration of the display

and the system.

As a safety measure, the driver must

only carry out operations requiring

sustained attention with the vehicle

stationary.

Connectivity.

Telephone.

Radio Media.

Connected navigation.

Adjust volume/Mute.

on/off.

For more information on the touch

screen, refer to the Audio and

telematics section.

41

Instruments

Driving menu

The systems with settings that can be adjusted are detailed in the table below.

For more information on a driving assistance system refer to the corresponding section.

Button

Corresponding function

Comments

Under-inflation initialisation Reinitialisation of the under-inflation system.

Blind spot monitoring

system

Activation/Deactivation of the function.

Stop & Start system

Lane departure warning

system

or

Automatic headlamp dip

Activation/Deactivation of the function.

42

Instruments

Button

Corresponding function

Comments

1

Vehicle settings

Access to other functions with settings that can be adjusted.

Select or deselect the tabs at the bottom of the touch screen to sort the display of the desired

functions.

To deactivate/activate a

function, press oFF/oN.

To modify a setting (lighting

duration, ...) or find additional

information, press the symbol

for the function.

-

Lighting:

-

"Directional headlamps": activation/deactivation of the directional headlamps.

"guide-me-home lighting": activation/deactivation of the automatic guide-me-home lighting.

"Welcome lighting": activation/deactivation of the exterior welcome lighting.

"Mood lighting": activation/deactivation of the interior mood lighting.

-

Access:

-

"Hands-Free Access": activation/deactivation of the motorized opening and closing of a side

door by the hands-free system,

-

"Locks your vehicle after the motorized closing of a side door, using hands-free access.":

activation/deactivation of the locking of your vehicle after the motorized closing of a side door

by the hands-free system.

-

Assistance (driving aids):

-

"Rear wiper in reverse": activation/deactivation of the operation of the rear wiper in reverse.

"Recommended speed display": activation/deactivation of the speed limit recognition system,

allowing a speed setting to be given to the cruise control or speed limiter.

-

"Collision risk alert and automatic braking": activation/deactivation of collision risk alerts.

"Fatigue Detection System": activation/deactivation of the driver fatigue detection system.

Diagnostic

List of current alerts.

Parking sensors

Adjust speed settings

Activation/Deactivation of the function.

Memorisation of speed settings for the speed limiter or active cruise control.

43

Instruments

Setting the time and date

With the audio system

With the touch screen

F

Press on Settings for acces to

You can choose to synchronise the

time and date with the gPS navigation

system (if fitted to your vehicle) so

that these settings are adjusted

automatically.

the different menus.

F

Select "OPTIONS".

F

Press the MENU button for access to the

main menu.

F

Select "Setting the time-date".

F

Select the "Date" or "Time" tab.

F

Press the "7" or "8" button to select the

Personalisation-configuration menu,

then confirm by pressing the "OK" button.

Modify the settings in the associated

"Date" or "Time" fields then press on

"Confirm".

Press the "5" or "6" button to select the

Display configuration menu then confirm

by pressing the "OK" button.

F

Press on "Confirm" to save and

quit.

F

Press the "5" or "6" and "7" or "8" buttons

to set the date and time, then confirm by

pressing the "OK" button.

44

Instruments for Your Peugeot Traveller Van First Generation (2016-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals