2011-2017 Porsche Cayenne SUV Minor Repairs -> Towing User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Minor Repairs -> Towing for Your Porsche Cayenne SUV Second Generation (2011-2017)

Minor Repairs 303
f Put the gearshift lever in Neutral or move the
Tiptronic selector lever to position N.
The Tiptronic selector lever can no longer be
operated in the event of an electrical fault.
Locking of the Tiptronic selector lever in
position P can be overridden manually:
Please see the chapter “SELECTOR LEVER
EMERGENCY OPERATION” on page 184.
f The vehicle must always roll on all four wheels
when towed.
The ignition must be switched on so that the
brake lights and turn signal lights operate and
the steering lock cannot engage.
f Do not exceed a maximum speed of 30 mph
(50 km/h).
Maximum towing distance 30 miles (50 km).
If towing distances are greater, the vehicle
must be transported with a car transporter or
on a trailer.
Towing a four-wheel drive vehicle on one axle
We urge that wherever possible, a car transporter
or trailer be used to transport a Cayenne vehicle
that cannot move under its own power. This is the
safest way to transport a down vehicle.
For those instances where a car transporter or
trailer is not available, the vehicle may be towed
on all four axles only, provided the following
conditions are strictly met. Failure to meet these
conditions will result in serious and expensive
damage to the Tiptronic S transmission.
If the vehicle's transmission or shifter is already
damaged, serious damage will result if the vehicle
is not towed with all four wheels off the ground.
Porsche cannot be held responsible for damage
incurred in cases where a vehicle has been
transported on one or both of its axles.
f The vehicle must have all four wheels on the
ground when being towed or it must be
transported on a car transporter.
It is normally not permissible to raise one axle,
irrespective of whether it is the front or
rear axle.
If circumstances dictate that the vehicle must
be towed in this manner, the drive shaft
(cardan shaft) of the rolling axle must be
removed.
f Put the gearshift lever in Neutral or move
the Tiptronic selector lever to position N.
The Tiptronic selector lever can no longer be
operated in the event of an electrical fault.
Locking of the Tiptronic selector lever in
position P can be overridden manually.
Please see the chapter “SELECTOR LEVER
EMERGENCY OPERATION” on page 184.
f Switch ignition off.
The ignition key must remain in the ignition lock
so that the steering wheel lock does not
engage.
The control unit must be removed from the
ignition lock and the ignition key inserted in
vehicles with Porsche Entry & Drive:
Please see the chapter “EMERGENCY
OPERATION – UNLOCKING THE IGNITION KEY”
on page 149.
f Make sure that the vehicle is adequately
illuminated.
f Do not exceed a maximum speed of 30 mph
(50 km/h).
Maximum towing distance 30 miles (50 km).
If towing distances are greater, the vehicle
must be transported with a car transporter or
on a trailer.
Pulling out a vehicle stuck in snow,
sand, etc.
f Always pull out the stuck vehicle with the
greatest care.
f Do not pull out the vehicle abruptly or at an
angle.
f If possible, pull the vehicle out backwards in
its own tracks.
f Do not pull out the vehicle with a trailer
attached.
NOTICE
304 Minor Repairs
Towing hook
The towing hook is stored with the tool kit under
the luggage compartment floor.
Fitting the towing hook
1. Press the lower edge of the appropriate plastic
cover into the bumper until the cover
disengages.
2. Pull cover out of the bumper and let it hang by
its thread.
3. Screw in towing hook A as far as it will go
(left-hand thread) and tighten hand-tight.
Removing the towing hook
1. Unscrew the towing hook A.
2. Insert plastic cover at the lower edge of the
opening.
3. Fold the cover up and press on its upper edge
to engage it in the bumper.
Pulling vehicle onto flat bed
1. Position wooden ramps at the base of the flat
bed to reduce the angle of the pull.
2. Reel in the hoist cable and check the underside
of the vehicle for any interference.
Minor Repairs 305
Tying down vehicle on flat bed
1. Carefully feed towing straps through the
opening in the rear wheels.
Make sure metal parts of straps do not
damage rim.
Make sure the strap is flat over the rim bead.
Make sure brake backing plate is not
damaged.
2. Secure straps to rear of flat bed.
3. Reel in hoist cable only far enough to tension
tie-down straps.
4. Carefully feed towing straps through the
opening in the front wheels.
Make sure metal parts of straps do not
damage rim.
Make sure the strap is flat over the rim bead.
Make sure brake backing plate is not
damaged.
5. Secure straps to front of flat bed.
6. Release tension on hoist cable, but do not
disconnect.
Use hoist cable as safety cable.
Transporting the vehicle on car trains,
ferries and car transporters
f Tie the vehicle down only at its wheels.
f Deactivate passenger compartment
monitoring system and the inclination sensor.
f Please see the chapter “TEMPORARILY
DEACTIVATING PASSENGER COMPARTMENT
MONITORING SYSTEM AND INCLINATION
SENSOR” on page 235.

Related Topics

Popular Owner Manuals