2019-2024 Porsche Taycan 2 Door Child Restraint Systems (Child Seats) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Child Restraint Systems (Child Seats) for Your Porsche Taycan 2 Door First Generation (2019-2024)

A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Child Restraint Systems (Child Seats)
87
Child Restraint Systems
(Child Seats)
DANGER
Improper use of child re-
straint systems
Risk of serious or fatal injury resulting from the im-
proper use of child restraint systems.
Child restraint systems that are not suitable for the
vehicle type or that are not properly installed in the
vehicle do not provide adequate protection in the
event of an accident.
e Always refer to the separate installation instruc-
tions for the respective child restraint system.
e When using a child restraint system, always
comply with the legal regulations that apply in
your country.
e Use only child restraint systems recommended
by Porsche. These restraint systems have been
tested and adapted to suit the interior of Porsche
vehicles and the corresponding child weight
classes. Other systems have not been tested and
could increase the risk of injury.
e Switch off the passenger airbag if a child re-
straint system is installed in the passenger seat.
Porsche recommends Porsche Tequipment child re-
straint systems. For information on installation
options:
e Contact your Porsche partner.
> Please refer to chapter "Ensuring correct instal-
lation position of child restraint systems" on
page 91.
DANGER
Child restraint system in
the passenger seat
The passenger airbag offers protection only for per-
sons of a certain minimum height and minimum
weight. If a child restraint system is installed in the
passenger seat or if the seated passenger is a small
or light person, there is a risk of serious or fatal injury
from the passenger airbag deploying.
e Always check whether the passenger airbag
needs to be switched off before installing a child
restraint system in the passenger seat.
e Adjust the backrest angle of the passenger seat
so that there is solid contact between the pas-
senger seat and child restraint system.
> Please refer to chapter "Ensuring correct instal-
lation position of child restraint systems" on
page 91.
> Please refer to chapter "Switching off the pas-
senger airbag" on page 41.
e Always switch off the seat heating if child re-
straint systems are installed.
e Before installing a child restraint system in which
the child sits forward-facing, adjust the relevant
headrest as high as possible.
If the headrest on the rear seat prevents you
from installing the child restraint system even
when adjusted to its highest position, the head-
rest must be removed. The headrest must always
be re-installed once the child restraint system
has been removed.
> Please refer to chapter "Removing and in-
stalling headrests on rear seats" on
page 226.
Fig. 57: Airbag warning sticker
Fig. 58: Airbag warning sticker on the sun visor
e Never remove, deface or render illegible airbag
warning stickers A or warning signs.
Using child restraint systems correctly
1. Use a child restraint system of the correct
weight and height category.
> Please refer to chapter "Using child restraint
systems of the correct weight and size class"
on page 88.
2. Use the correct installation position for child re-
straint systems.
> Please refer to chapter "Ensuring correct in-
stallation position of child restraint systems"
on page 91.
3. Install the child restraint system securely.
> Please refer to chapter "Installing child re-
straint systems" on page 93.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Child Restraint Systems (Child Seats)
88
Using child restraint systems of
the correct weight and size class
e In addition the suitable weight and size class, al-
so check the correct installation position.
> Please refer to chapter "Ensuring correct instal-
lation position of child restraint systems" on
page 91.
Fig. 59: Example of ECE child restraint system sticker
A Size category
B "Universal" or "semi universal" marking
C Weight class
e In the case of child restraint systems with semi
universal approval, please refer to the vehicle
type list provided with the relevant child restraint
system or available on the Internet.
Classification of child restraint systems into
weight classes
Children in group 0 and 0+: up to 13 kg
(secured with i-Size system, ISOFIX system and
vehicle seat belt)
Children in this group are carried in child restraint
systems facing backward.
Whenever possible, these child restraint systems
should be installed on the rear seats.
Children in group I: 9 to 18 kg
(secured with i-Size system, ISOFIX system or ve-
hicle seat belt)
Children in this group must be carried in child re-
straint systems facing forward. In exceptional cases,
children in this weight group can also be carried in
special child restraint systems that are facing back-
ward. Whenever possible, these child restraint sys-
tems should be installed on the rear seats.
Children in group II: 15 to 25 kg
(secured with the vehicle seat belt)
Children in this group must be carried in child re-
straint systems facing forward. Whenever possible,
these child restraint systems should be installed on
the rear seats.
Children in group III: 22 to 36 kg
(secured with the vehicle seat belt)
Children in this group must be carried in child re-
straint systems facing forward. Whenever possible,
these child restraint systems should be installed on
the rear seats.
Classification of child restraint systems by
size classes
A ISO/F3: front-facing, full-height child restraint
system
B ISO/F2: front-facing, reduced-height child re-
straint system
B1 ISO/F2X: front-facing, reduced-height child
restraint system
B2 ISO/B2: front-facing child restraint system
with backrest
C ISO/R3: rear-facing, full-size child restraint
system
D ISO/R2: rear-facing, reduced-size child re-
straint system
E ISO/R1: rear-facing, child restraint system for
infants
F ISO/L1: left side-facing child restraint system
(baby carrier)
G ISO/L2: right side-facing child restraint system
(baby carrier)
e Observe the scope of application of the child re-
straint system as well as the manufacturer's in-
stallation and operating instructions for the child
restraint system being used.
Weight class Size category Child re-
straint
system
Group 0: 0 to
10 kg
F ISO/L1
G ISO/L2
E ISO/R1
Group 0+: 0
to 13 kg
C ISO/R3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Child Restraint Systems (Child Seats)
89
Weight class Size category Child re-
straint
system
D ISO/R2
E ISO/R1
Group I: 9 to
18 kg
i-Size child
restraint sys-
tems
1
A ISO/F3
B ISO/F2
B1 ISO/F2X
B2 ISO/B2
C ISO/R3
D ISO/R2
1. Country-dependent
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Child Restraint Systems (Child Seats)
90
Recommended child restraint systems
Weight class Manufacturer Secured with the vehicle seat belt Secured with i-Size and ISOFIX system
1
Type Authorisation
number
Porsche part
number
Type Authorisation
number
Porsche part
number
Group 0 and 0+: up to
13 kg
Britax-Römer Porsche Baby
Seat G0+
E1 04301146 955.044.805.84 Porsche Baby-
seat ISOFIX G0+
only in conjunc-
tion with: Base
ISOFIX
1
E1 04301146 955.044.805.84
only in conjunc-
tion with:
955.044.805.97
Group I: 9 to 18 kg Britax-Römer Porsche Junior
Seat ISOFIX G1
2,
E1 04301199 955.044.806.13 Porsche Junior
Seat ISOFIX G1
2, 1
E1 04301199 955.044.806.13
Group II: 15 to 25 kg Britax-Römer Porsche Junior
Plus G2 + G3
E1 04301169 955.044.806.19 Porsche Junior
Plus ISOFIT G2
+ G3
1
E1 04301198 955.044.806.18
Group III: 22 to 36 kg Britax-Römer Porsche Junior
Plus G2 + G3
E1 04301169 955.044.806.19 Porsche Junior
Plus ISOFIT G2
+ G3
1
E1 04301198 955.044.806.18
1. There is no i-Size or ISOFIX system available for the passenger seat.
2. Not permissible for use on the centre rear seat (vehicle with 3 rear seats) because this seat is not suitable for installation of child restraint systems with support leg.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Child Restraint Systems (Child Seats)
91
Ensuring correct installation posi-
tion of child restraint systems
Fig. 60: Seat numbering for installation of child restraint
systems in vehicles with 3 rear seats
A Left-hand drive vehicle with 3 rear seats
B Right-hand drive vehicle with 3 rear seats
Fig. 61: Seat numbering for installation of child restraint
systems in vehicles with 2 rear seats
A Left-hand drive vehicle with 2 rear seats
B Right-hand drive vehicle with 2 rear seats
Overview of how child restraint systems can be used
in accordance with standard ECE-R 16.
Fig. 62: ISOFIX and i-Size symbols
A Symbol for attachment of an ISOFIX child restraint sys-
tem (country-dependent)
B Symbol for attachment of an i-Size child restraint sys-
tem (country-dependent)
i-Size and ISOFIX are standardised anchorage sys-
tems for child restraint systems which are available
on a country-dependent basis. ISOFIX child restraint
systems and i-Size child restraint systems which are
approved in accordance with ECE-R 129 and ECE-R
44 can be attached to the i-Size anchorage points.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Child Restraint Systems (Child Seats)
92
Secured with i-Size system Secured with the vehicle seat belt Secured with ISOFIX system
Permissible installation positions ac-
cording to seat numbering
4 and 6 3, 4, 5
1
and 6 4 and 6
Seat numbering for installation of child restraint systems 1 3
2
4
3
5
4, 1
6
3
Secured with the vehicle seat belt No Yes Yes Yes Yes
ISOFIX installation position No No Yes No Yes
i-Size installation position No No Yes No Yes
Sideward-facing child restraint systems No No No No No
Largest suitable rear-facing child restraint system No R2 R3 R2
5
R3
Largest suitable forward-facing child restraint system No F3/B2 F3 F2X
5
F3/B2
No: Seat is not suitable for installation of a child restraint system of this group.
Overview of installation of child restraint
systems on the passenger seat
When installing child restraint systems of the Uni-
versal (U) or "semi universal" (L) approval categories
on the passenger seat, check whether the passenger
airbag needs to be switched off using the table
below.
For information on the approval category, please re-
fer to the orange certification mark on the child re-
straint system.
X: Seat is not suitable for child restraint sys-
tems of this group.
U / L: Suitable for forward-facing child restraint
systems in the “Universal” or "semi univer-
sal" approval categories, which are secured
with the seat belt for adults and are ap-
proved for use with this group.
1. Seat 5 is only available for vehicles with 3 rear seats and is only suitable for installing child restraint systems secured with the vehicle seat belt.
2. Always check whether the passenger airbag needs to be switched off.
3. This installation position is suitable for child restraint systems with support leg.
4. This installation position is not suitable for child restraint systems with support leg.
5. Secured with the vehicle seat belt.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Child Restraint Systems (Child Seats)
93
Group Passenger airbag switched on
1
Passenger airbag switched off
Group 0:
0 to 10 kg
X U / L
Group 0+:
0 to 13 kg
X U / L
Group I:
9 to 18 kg
Backward-facing
X U / L
Group I:
9 to 18 kg
Forward-facing
U / L U / L
Group II:
15 to 25 kg
U / L U / L
Group III:
22 to 36 kg
U / L U / L
Installing child restraint systems
Baby carriers
Left or right-facing child restraint systems from size
categories F and G (e.g. baby carriers) should not
generally be used on any of the seat versions.
Porsche recommends Porsche Tequipment child re-
straint systems (e.g. Porsche Babyseat ISOFIX G0+).
Switching passenger airbag on and off
DANGER
Passenger airbag
switched off
The passenger airbag will not be triggered in an ac-
cident if it is switched off.
e Only switch off the passenger airbag if a child
restraint system is fitted on the passenger seat.
e Switch the passenger airbag back on once the
child restraint system has been removed.
1. Adjust the passenger seat to the rearmost upper position.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Child Restraint Systems (Child Seats)
94
Fig. 63: Switching off the passenger airbag
bb Vehicle switched off.
1. Open the glove box.
2. Remove the emergency key from the driver's key.
> Please refer to chapter "Driver's Key" on
page 104.
NOTICE
Risk of damage to the key switch and airbag system
e Only turn the emergency key when it is inserted
fully into the key switch.
It must be possible to turn the key switch with-
out exerting excessive force.
e Only switch the passenger airbag on or off when
the vehicle is switched off.
3. Insert the emergency key as far as it will go into
the key switch.
4. Using the emergency key, switch the passenger
airbag off (switch position OFF) or on (switch
position ON).
DANGER
Risk of serious or fatal
injury due to the passen-
ger airbag triggering
inadvertently
If the emergency key is left in the key switch during
driving, it may inadvertently turn in the key switch
due to vibration, possibly triggering the airbag.
e Never leave the emergency key in the key switch
while driving.
5. Remove the emergency key from the key switch.
6. Close the glove box.
PASSENGER AIR BAG OFF/ON indicator
Fig. 64: PASSENGER AIR BAG OFF/ON indicator
The PASSENGER AIR BAG OFF/ON indicator is lo-
cated on the overhead console.
Lamp check
Once readiness for operation is established, the
PASSENGER AIR BAG OFF/ON indicator comes on
for approx. 5 seconds for a lamp check.
Passenger airbag switched off
When the passenger airbag is switched off, the
PASSENGER AIR BAG OFF indicator stays on when
readiness for operation is established.
Passenger airbag switched on
When the passenger airbag is switched on, the
PASSENGER AIR BAG ON indicator comes on for
approx. 1 minute when readiness for operation is
established and then goes off.
DANGER
Failure or malfunction of
the passenger airbag
If the PASSENGER AIR BAG OFF indicator does not
come on when readiness for operation is established
and the passenger airbag is switched off, there may
be a fault in the system.
e Do not install a child restraint system on the
passenger seat.
e Visit a qualified specialist workshop. Porsche
recommends a Porsche partner as they have
trained workshop personnel and the necessary
parts and tools.
Installing child restraint system with vehicle
seat belt
Installing child restraint system on rear seats with
vehicle seat belt
1. Adjust the backrest angle of the passenger seat
so that there is solid contact between the pas-
senger seat and child restraint system.
2. Adjust the passenger seat to the rearmost upper
position.
> Please refer to chapter "seats" on page 223.
3. If possible, adjust the seat belt guide on the
backrest of the child restraint system so that it is
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Child Restraint Systems (Child Seats)
95
in front of and underneath the belt outlet on the
B-pillar of the vehicle.
4. Make sure there is a comfortable distance be-
tween the passenger seat and the passenger
sitting behind it and if necessary, adjust the
passenger seat as required.
5. Make sure to leave a comfortable space between
the child's feet and legs and the dashboard and if
necessary, adjust the passenger seat as required.
Installing child restraint system on rear seats with
vehicle seat belt
e For booster seats with no backrest, make sure
that the booster seat is touching the rear seat
backrest.
Installing child restraint system with i-Size or
ISOFIX system
> Please refer to chapter "Using child restraint
systems of the correct weight and size class" on
page 88.
e Always refer to the separate installation instruc-
tions for your child restraint system.
Installing child restraint system on the rear seats
Fig. 65: i-Size or ISOFIX anchorage system on rear seats
(country-dependent)
The retaining lugs A of the i-Size or ISOFIX anchor-
age system for the child restraint system are located
under the marked protection caps on the seat
cushion.
1. Remove the protection caps of the i-Size or ISO-
FIX anchorage system if necessary and put them
in a safe place.
2. Secure the child restraint system to retaining
lugs A as described in the instruction manual for
the child restraint system.
3. Pull the child restraint system to check that both
anchorage points are properly engaged.
4. Ensure a comfortable distance between the front
passenger seat and a passenger sitting behind it.
To prevent it from rotating, the child restraint sys-
tem must be additionally secured with the support
leg or top tether.
Installing child restraint system with support leg
Fig. 66: Installing child restraint system with support leg
1. Install the child restraint system with ISOFIX or i-
Size anchorage correctly using the retaining lug
A.
> Please refer to chapter "Installing child re-
straint system with i-Size or ISOFIX system"
on page 95.
2. Position the support leg in accordance with the
child restraint system manufacturer's
instructions.
3. Ensure that the child restraint system is posi-
tioned flush against the rear seat.
Installing child restraint system with top tether
e When using a child restraint system with top
tether, the top tether must be attached at the
anchorage points on the back of the rear seat
backrests.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Child Restraint Systems (Child Seats)
96
Fig. 67: Anchorage points for top tether
1. Open the top tether cover.
Fig. 68: Installing child restraint system with top tether
2. Install the child restraint system with ISOFIX or i-
Size anchorage correctly with the retaining lug A.
> Please refer to chapter "Installing child re-
straint system with i-Size or ISOFIX system"
on page 95.
3. Guide the top tether B through the headrest. The
headrest can be removed for ease of installation.
> Please refer to chapter "Removing and in-
stalling headrests on rear seats" on
page 226.
Fig. 69: Securing child restraint system with i-Size or ISOFIX
top tether
4. Fasten the top tether to the anchorage point on
the rear of the backrest and tighten the top
tether.

Related Topics

Popular Owner Manuals