2025-2026 Porsche Taycan 2 Door Adaptive Cruise Control (ACC) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Adaptive Cruise Control (ACC) for Your Porsche Taycan 2 Door Second Generation (2025-2026)

A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Adaptive Cruise Control (ACC)
34
Adaptive Cruise Control
(ACC)
General safety instructions
WARNING
Lack of attention
The increased comfort offered by the system should
not induce you to risk your safety. The driver remains
responsible when driving, such as by keeping a safe
distance or driving at an appropriate speed, even
when the system is activated. The system cannot
replace the driver's attentiveness.
e Drive with extreme care.
e If the system-related deceleration is insufficient,
slow the vehicle down immediately using the
footbrake.
e Make sure that it is possible to take over control
of the vehicle at all times.
WARNING
Unsafe traffic situations
and unfavourable road
conditions
Use of the system may cause accidents if the cur-
rent situation does not permit driving safely at an
adequate distance from the vehicle in front and at a
constant speed.
When driving in turn-off lanes, motorway exits or in
areas with roadworks, the vehicle can accelerate to
the set speed.
e Do not use the system in heavy traffic, where
there are road works, in built-up areas, on private
or field tracks, or in areas with traffic calming.
e Switch off the system temporarily when driving
on turn-off lanes, motorway exits or in areas with
roadworks.
WARNING
Covered radar sensor
Covering the radar sensor can adversely affect or
disable the function of the system.
e The radar sensor must always be kept free of
dirt, ice and snow.
Fig. 7: Location of the radar sensor
WARNING
Damage to the radar
sensor
Shocks or damage to the bumper, wheel housings or
underbody, e.g. through parking collisions, may
move the sensors. This may impair performance of
the Adaptive Cruise Control.
e Visit a qualified specialist workshop. Porsche
recommends a Porsche partner as they have
trained workshop personnel and the necessary
parts and tools.
WARNING
Foot placed on the ac-
celerator pedal
The system does not brake automatically when the
foot is placed on the accelerator pedal. Placing the
foot on the accelerator may override cruise and dis-
tance control.
e When the system is activated, remove your foot
from the accelerator pedal.
WARNING
Inadequate braking
power during automatic
braking by the system
If the system detects that braking assistance is re-
quired on the part of the driver, a warning signal
sounds and a warning symbol appears on the in-
strument cluster. In this case, the braking power of
the system is not sufficient to prevent a collision.
e You must brake immediately in this case.
System limitations
WARNING
Unfavourable road and
weather conditions
Radar sensor vision can be impaired by rain, snow,
ice, fog, loose gravel or spray. Vehicles in front will
not be detected properly or may not be detected at
all.
Reflective objects such as ice, heavy rain, crash bar-
riers or tunnel entrances may impair the functional-
ity of the radar sensor. A message indicating that the
system is not available will appear on the instrument
cluster.
e Do not use the system under such conditions.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Adaptive Cruise Control (ACC)
35
WARNING
Undetected vehicles or
objects
The radar sensor detects a narrow, cone-shaped
area in front of your vehicle. As a result, vehicles or
objects may not be detected in time or cannot be
detected in the following situations:
– in the case of vehicles that change lanes or cut in
– in the case of vehicles with a small cross-section
or narrow vehicles
– when driving into and out of bends
– in the case of stationary vehicles
– in the case of vehicles with large overhangs
– in the case of pedestrians, cyclists and animals
– in the case of objects on the road
– in the case of oncoming vehicles and cross traffic
e Take action and brake if necessary.
e Drive with extreme care and always pay attention
to the traffic conditions and vehicle
surroundings.
Vehicles changing lanes or cutting in and
narrow vehicles
Fig. 8: Vehicles changing lanes or cutting in (A) and narrow
vehicles (B)
A vehicle changing lanes or cutting in will not be
detected until it is completely in the same lane.
A narrow vehicle will not be detected or will be de-
tected too late.
Cornering and stationary vehicles
Fig. 9: Cornering (C) and stationary vehicles (D)
When driving into and out of bends, vehicles will not
be detected or will be detected too late, or the sys-
tem will react to vehicles in adjacent lanes.
A stationary vehicle or obstacle that appears sud-
denly in the detection field of the radar sensor, such
as after a vehicle in front changes lanes or at the end
of a traffic jam, can only be detected by Adaptive
Cruise Control (ACC) to a limited extent.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Adaptive Cruise Control (ACC)
36
Vehicles with large overhangs
Fig. 10: Vehicles with large overhangs
If there is a vehicle in front with a long overhang,
such as a timber lorry, the radar sensor may not de-
tect the end of the vehicle or may detect it
incorrectly.
Responding to warning messages
Always heed any warning and information messages
displayed in the vehicle.
> Please refer to chapter "Warning and information
messages" on page 271.
Operating principle
Adaptive cruise control (ACC) operates between ap-
prox. 30 and 210 km/h (20 and 130 mph) to auto-
matically maintain a selected speed and distance
without you having to use the accelerator pedal.
If a vehicle travelling at less than the selected speed
is detected in the same lane, ACC automatically
maintains a specific distance. Adaptive cruise con-
trol applies the brakes if the distance to the vehicle
ahead becomes too short, and it accelerates if the
distance increases.
If the vehicle in front stops, ACC will slow down to a
stop; it will automatically resume driving again if the
vehicle in front starts moving again within 15 sec-
onds. Otherwise, automatic speed control and dis-
tance control can be resumed by the driver.
The speed of the vehicle can be increased at any
time by pressing the accelerator. The stored desired
speed and distance are retained and restored after
the accelerator pedal is released. The speed of the
vehicle can be reduced at any time by braking. This
will switch the system to passive operating
condition.
Controls
Fig. 11: Control stalk for driver assistance systems
R Switch systems on/off and open the options menu
S Open the options menu (when the system is switched
on)
1 Set/increase the desired speed
2 Reduce the desired speed
3 RESUME: Resume control, adopt speed
4 CANCEL: Interrupt control
Display elements
Fig. 12: ACC display
A Own speed
B Setting the desired speed
C Speed of vehicle in front
D Vehicle detected in front
E Desired distance from the vehicle in front
F Status display and desired speed
Status display symbols
Symbol Meaning
ACC is passive.
ACC is passive at the set desired
speed.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Adaptive Cruise Control (ACC)
37
Symbol Meaning
ACC is active at the set desired
speed.
A vehicle was detected ahead while
the desired speed was set. A vehicle
symbol is displayed instead of the
cruise control symbol.
Operating states
Passive
This mode is set after switching on and when ACC is
active after pressing the brake pedal and after
pressing down the control stalk (CANCEL).
– The status display F is grey.
– There is no control.
– The set desired speed and the set desired dis-
tance are retained.
Active
This mode is set after setting the speed, after re-
suming control (RESUME) and after temporarily
overriding control by pressing the accelerator pedal.
– The status display F is green.
– Speed and distance to the vehicle ahead are
controlled.
Temporarily passive
This mode is set while the accelerator pedal is
pressed when ACC is active.
– A message indicating that ACC is passive ap-
pears in the instrument cluster.
– The status display F is grey.
– There is no control.
– The set desired speed and the set desired dis-
tance are retained.
– Control is active again after releasing the accel-
erator pedal.
Switch ACC on and off
The system that was selected last is always
switched on. The system is initially in passive mode
when switched on. It must first be activated before
the control function starts working.
Switching the ACC on
bb No driver assistance system has been switched
on yet.
1. Press the R button on the control stalk.
The options menu for the driver assistance sys-
tems appears on the instrument cluster.
2. If ACC is not already selected, select ACC using
the rotary knob on the steering wheel and press
to confirm.
ACC is switched on and passive.
Switching from an already activated driver assis-
tance system to ACC
1. Press the S button on the control stalk.
The options menu for the driver assistance sys-
tems appears on the instrument cluster.
2. Select ACC using the rotary knob on the steering
wheel and press to confirm.
ACC is switched on and passive.
Information
The last selected driver assistance system is re-
tained even after switching it off and operational
readiness is restored.
Switching off ACC
e Press the R button on the control stalk.
The set desired speed is deleted.
The desired distance is stored.
Activating ACC
bb ACC switched on.
1. Accelerate or decelerate to the desired speed
using the accelerator pedal.
2. Briefly press the control stalk forward (position
1) and release the accelerator pedal.
ACC is active.
The current driving speed is set as the desired
speed.
The current desired speed is green in the status dis-
play and is automatically maintained unless a slower
vehicle is detected ahead.
Changing the desired speed
The set desired speed can be changed by pressing
the control stalk.
bb ACC is active.
Increasing the speed
e Press the control stalk forward (position 1):
– Brief press = 1 km/h (1 mph) increments
– Press and hold = 10 km/h (6 mph)
increments
Reducing the speed
e Pull the control stalk (position 2):
– Brief pull = 1 km/h (1 mph) increments
– Pull and hold = 10 km/h (6 mph) increments
The set desired speed is indicated by the outer line
at the edge of the speedometer and appears blue in
the status display F. The display turns green as soon
as the set desired speed is reached.
Changing the desired distance
The desired distance from the vehicle in front can be
set in 5 stages. Stage 3 is recommended. The
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Adaptive Cruise Control (ACC)
38
distance depends on the driving speed. It reduces as
the vehicle slows down and increases as it speeds
up.
Fig. 13: Setting the desired distance
Increasing the desired distance
e Press rocker switch Z upwards.
Another segment is shown in desired distance
display E.
Reducing the desired distance
e Press rocker switch Z downwards.
A segment disappears in desired distance display
E.
Information
When the system display is not active, pressing
rocker switch Z for the first time displays the main
menu for the driver assistance system without
changing the desired distance.
Displaying the distance from the vehicle in
front
The shorter the distance from vehicle in front D, the
larger the vehicle displayed in area E. The longer the
distance from vehicle in front D, the smaller the ve-
hicle displayed in area E.
Symbol Suitable for Distance at 120
km/h (75 mph)
Speedy driving in
lines of traffic
approx. 33 m (≙
1 sec.)
Driving in stop-
and-go traffic
approx. 47 m
(≙ ap-
prox. 1.4 sec.)
Corresponds to
"two seconds
time headway"
approx. 60 m
(≙ ap-
prox. 1.8 sec.)
Driving on coun-
try roads
approx. 73 m
(≙ ap-
prox. 2.2 sec.)
Driving in sparse
traffic
approx. 87 m
(≙ ap-
prox. 2.6 sec.)
Overriding speed and distance
control temporarily
Speed and distance control can be overridden tem-
porarily by pressing the accelerator pedal. This is
useful while overtaking, for example.
bb ACC is active.
1. Press the accelerator.
The system is passive while the accelerator
pedal is pressed (operating status temporarily
passive).
2. Take your foot off the accelerator pedal.
The system is active.
Interrupting and resuming speed
and distance control
If the system is interrupted, it switches to passive
standby mode and remains in standby until it is ac-
tivated again manually.
Interrupting control
e Press the brake pedal.
– or –
e Press the control stalk down (CANCEL).
The system is passive. The desired speed and
distance settings remain stored.
The status display changes from green to grey.
Information
When the vehicle is stationary, the speed and dis-
tance control can only be cancelled using the control
stalk.
Resuming control
e Tap the control stalk up (RESUME).
The system is active. The desired speed and
distance settings are applied again.
The status display changes from grey to green.
Information
ACC can be activated even while the vehicle is sta-
tionary by tilting the control stalk upwards.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Adaptive Cruise Control (ACC)
39
Braking to a standstill and driving
off again
If the vehicle in front stops, your vehicle will slow
down and come to a stop within the control limits of
the system if distance control is active.
Information
When distance control is active or while the vehicle
is held, the brake pedal may feel different and you
may hear hydraulic noises. This behaviour is normal
for the system. It is not a fault.
Driving off again automatically
WARNING
Driving off when there is
an obstacle
The vehicle may start driving again in stop-and-go
traffic even if there is an obstacle between your ve-
hicle and the vehicle in front. This can result in a
collision.
e Brake immediately in this case.
After your vehicle is automatically braked to a
standstill, the system assists the driver in driving off
again automatically within 15 seconds.
A message on the instrument cluster informs the
driver that the vehicle is ready to drive off.
Driving off manually
Several seconds after the vehicle is automatically
braked to a standstill, the message indicating read-
iness to drive off disappears. The vehicle must then
be driven off again manually.
Driving off manually when the system is active
bb No obstructions detected in front.
e Press the control stalk up (RESUME).
– or –
e Press the accelerator pedal briefly.
Driving off manually when the system is passive
bb No obstructions detected in front.
e Press the control stalk up (RESUME).

Related Topics

Popular Owner Manuals