2025-2026 Porsche Taycan 2 Door Adaptive Cruise Control (ACC) -> Display elements User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Adaptive Cruise Control (ACC) -> Display elements for Your Porsche Taycan 2 Door Second Generation (2025-2026)

A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Adaptive Cruise Control (ACC)
36
Vehicles with large overhangs
Fig. 10: Vehicles with large overhangs
If there is a vehicle in front with a long overhang,
such as a timber lorry, the radar sensor may not de-
tect the end of the vehicle or may detect it
incorrectly.
Responding to warning messages
Always heed any warning and information messages
displayed in the vehicle.
> Please refer to chapter "Warning and information
messages" on page 271.
Operating principle
Adaptive cruise control (ACC) operates between ap-
prox. 30 and 210 km/h (20 and 130 mph) to auto-
matically maintain a selected speed and distance
without you having to use the accelerator pedal.
If a vehicle travelling at less than the selected speed
is detected in the same lane, ACC automatically
maintains a specific distance. Adaptive cruise con-
trol applies the brakes if the distance to the vehicle
ahead becomes too short, and it accelerates if the
distance increases.
If the vehicle in front stops, ACC will slow down to a
stop; it will automatically resume driving again if the
vehicle in front starts moving again within 15 sec-
onds. Otherwise, automatic speed control and dis-
tance control can be resumed by the driver.
The speed of the vehicle can be increased at any
time by pressing the accelerator. The stored desired
speed and distance are retained and restored after
the accelerator pedal is released. The speed of the
vehicle can be reduced at any time by braking. This
will switch the system to passive operating
condition.
Controls
Fig. 11: Control stalk for driver assistance systems
R Switch systems on/off and open the options menu
S Open the options menu (when the system is switched
on)
1 Set/increase the desired speed
2 Reduce the desired speed
3 RESUME: Resume control, adopt speed
4 CANCEL: Interrupt control
Display elements
Fig. 12: ACC display
A Own speed
B Setting the desired speed
C Speed of vehicle in front
D Vehicle detected in front
E Desired distance from the vehicle in front
F Status display and desired speed
Status display symbols
Symbol Meaning
ACC is passive.
ACC is passive at the set desired
speed.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Adaptive Cruise Control (ACC)
37
Symbol Meaning
ACC is active at the set desired
speed.
A vehicle was detected ahead while
the desired speed was set. A vehicle
symbol is displayed instead of the
cruise control symbol.
Operating states
Passive
This mode is set after switching on and when ACC is
active after pressing the brake pedal and after
pressing down the control stalk (CANCEL).
– The status display F is grey.
– There is no control.
– The set desired speed and the set desired dis-
tance are retained.
Active
This mode is set after setting the speed, after re-
suming control (RESUME) and after temporarily
overriding control by pressing the accelerator pedal.
– The status display F is green.
– Speed and distance to the vehicle ahead are
controlled.
Temporarily passive
This mode is set while the accelerator pedal is
pressed when ACC is active.
– A message indicating that ACC is passive ap-
pears in the instrument cluster.
– The status display F is grey.
– There is no control.
– The set desired speed and the set desired dis-
tance are retained.
– Control is active again after releasing the accel-
erator pedal.
Switch ACC on and off
The system that was selected last is always
switched on. The system is initially in passive mode
when switched on. It must first be activated before
the control function starts working.
Switching the ACC on
bb No driver assistance system has been switched
on yet.
1. Press the R button on the control stalk.
The options menu for the driver assistance sys-
tems appears on the instrument cluster.
2. If ACC is not already selected, select ACC using
the rotary knob on the steering wheel and press
to confirm.
ACC is switched on and passive.
Switching from an already activated driver assis-
tance system to ACC
1. Press the S button on the control stalk.
The options menu for the driver assistance sys-
tems appears on the instrument cluster.
2. Select ACC using the rotary knob on the steering
wheel and press to confirm.
ACC is switched on and passive.
Information
The last selected driver assistance system is re-
tained even after switching it off and operational
readiness is restored.
Switching off ACC
e Press the R button on the control stalk.
The set desired speed is deleted.
The desired distance is stored.
Activating ACC
bb ACC switched on.
1. Accelerate or decelerate to the desired speed
using the accelerator pedal.
2. Briefly press the control stalk forward (position
1) and release the accelerator pedal.
ACC is active.
The current driving speed is set as the desired
speed.
The current desired speed is green in the status dis-
play and is automatically maintained unless a slower
vehicle is detected ahead.
Changing the desired speed
The set desired speed can be changed by pressing
the control stalk.
bb ACC is active.
Increasing the speed
e Press the control stalk forward (position 1):
– Brief press = 1 km/h (1 mph) increments
– Press and hold = 10 km/h (6 mph)
increments
Reducing the speed
e Pull the control stalk (position 2):
– Brief pull = 1 km/h (1 mph) increments
– Pull and hold = 10 km/h (6 mph) increments
The set desired speed is indicated by the outer line
at the edge of the speedometer and appears blue in
the status display F. The display turns green as soon
as the set desired speed is reached.
Changing the desired distance
The desired distance from the vehicle in front can be
set in 5 stages. Stage 3 is recommended. The

Related Topics

Popular Owner Manuals