2025-2026 Porsche Taycan 2 Door Tyres and Wheels -> Changing a wheel User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Tyres and Wheels -> Changing a wheel for Your Porsche Taycan 2 Door Second Generation (2025-2026)

A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tyres and Wheels
254
located in the main tread channels and display the
minimum tread depth of 1.6 mm.
e Check the tyre tread regularly, particularly before
and after long journeys.
Measuring the tyre tread depth
e Insert a commercially available tread depth
gauge or calliper in the tyre tread and measure
the tyre tread depth.
Information
Uneven tyre wear indicates a defect on the vehicle:
e Visit a qualified specialist workshop. Porsche
recommends a Porsche partner as they have
trained workshop personnel and the necessary
parts and tools.
Storing wheels
Tyres must not be more than 6 years old. Chemical
additives, which make the rubber in the tyre elastic,
lose their effect over the course of time and the
rubber becomes brittle. The age of a tyre can be
seen from the DOT code on the tyre sidewall. If the
last four digits are 3016, for example, the tyre was
manufactured in the 30th week of 2016.
e Always store wheels in cool, dry and dark condi-
tions. Tyres without rims should be stored in a
standing position.
e Do not store summer tyres or park vehicles fitted
with summer tyres at ambient temperatures be-
low –15 °C.
e Avoid contact with petrol, oil and grease.
Balancing wheels
As a precaution, have wheels balanced in spring
(summer tyres) and before winter (M+S tyres).
e Visit a qualified specialist workshop. Porsche
recommends a Porsche partner as they have
trained workshop personnel and the necessary
parts and tools.
Changing a wheel
WARNING
Working under the
vehicle
The vehicle can slip off the jack.
e Make sure that no one is in the vehicle when
jacking up and changing a wheel.
e Raise the vehicle only at the prescribed jacking
points on the vehicle underbody.
e Never jack up the vehicle when it is parked on a
surface that slopes up, down or to the side.
e Only use the jack to raise the vehicle for chang-
ing wheels.
e Always place the vehicle on solid supports when
working under the vehicle.
> Please refer to chapter "Jack and Lifting Plat-
form" on page 138.
Information
The tools needed for changing wheels (jack, wheel
bolt wrench, mounting aids, etc.) are not included in
the standard scope of supply for the vehicle.
e For information on the tool required: Contact
your Porsche partner.
Information
The tyre and wheel sizes are different on each of the
two axles. When wheels are removed, mark the di-
rection of rotation and position of each wheel and fit
the wheels in accordance with this marking.
e Only use wheels/tyres with approved dimensions
for each axle.
Vehicle registration documents or Please refer to
chapter "Technical Data" on page 308.
Caring for wheel attachment faces
Fig. 213: Wheel attachment faces
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tyres and Wheels
255
NOTICE
Risk of damage to the wheel and wheel attachment
face.
e The wheel attachment face B on the brake disc
and on the wheel hub itself must not be greased.
e Only the areas A may be greased. Grease these
areas very thinly with Optimoly
®
TA: Contact your
Porsche partner. Do not use any other grease or
paste.
Caring for wheel bolts
e Always clean the wheel bolts before fitting.
e Wheel bolts must not be greased.
e Replace damaged wheel bolts. Only use genuine
Porsche wheel bolts intended for this particular
model or wheel bolts of similar quality which
have been manufactured according to Porsche
specifications and production requirements.
e Tighten wheel bolts to a tightening torque of
160 Nm (118 ftlb.).
e Do not use any force-activated tools such as
impact screwdrivers.
Using security wheel bolts
Fig. 214: Adapter for security wheel bolts
The adapter for the security wheel bolts is located in
the tool kit.
e To loosen and tighten the wheel bolt with an-
titheft protection, the adapter must be used be-
tween the wheel bolt and the wheel bolt wrench.
e When positioning the adapter ensure that it en-
gages fully in the teeth of the wheel bolt.
Changing a wheel
Preparing the vehicle
WARNING
Control operation of the
levelling system
A vehicle on which the levelling system is activated
can move unexpectedly or tip or fall off lifting
equipment, e.g. a jack or lifting platform. This can
result in serious injury and damage.
e Manually set Normal Level and switch off the
levelling system before lifting the vehicle.
e
e Setting e Vehicle e Additional chassis
settings e Deactivate chassis adjustment
before using a jack
1. Activate the electric parking brake.
2. Turn off the vehicle.
3. Secure the vehicle to prevent it from rolling
away, e.g. by placing wheel chocks at the wheels
on the opposite side.
4. Slightly loosen the wheel bolts or wheel nuts on
the wheel to be changed.
5. Lift the vehicle only at the specified jacking
points.
> Please refer to chapter "Jack and Lifting
Platform" on page 138.
6. Raise the vehicle until the wheel lifts off the
ground.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tyres and Wheels
256
Changing a wheel
Fig. 215: Screw in one assembly aid on vehicles without
PCCB
Fig. 216: Screw in two assembly aids on vehicles with PCCB
1. For vehicles without PCCB: Remove one wheel
bolt and screw in one assembly aid.
– or –
1. For vehicles with PCCB: Remove two wheel bolts
and screw in two assembly aids A and B.
NOTICE
The brake discs can become damaged in the case of
improper wheel change, especially in vehicles with
PCCB.
e Screw in assembly aids when changing a wheel.
2. Remove the remaining wheel bolts.
3. Remove the wheel.
4. Fit a new wheel.
5. Insert wheel bolts and tighten slightly in diago-
nally opposite sequence.
6. Remove assembly aids and screw in remaining
wheel bolts. Initially tighten wheel bolts only
slightly in diagonally opposite sequence so that
the wheel is centred.
7. Inflate the tyre if necessary.
8. Lower the vehicle fully and remove the jack.
9. Tighten the wheel bolts in diagonally opposite
sequence. Do not use any force-activated tools
such as impact screwdrivers.
10.Immediately after changing a wheel, use a tor-
que wrench to check the prescribed tightening
torque of the wheel bolts (1600 Nm /
1180 ftlb.).
11.The settings for Tyre Pressure Monitoring (TPM)
are updated.
> Please refer to chapter "Teaching in Tyre
Pressure Monitoring" on page 251.

Related Topics

Popular Owner Manuals