2025-2026 Porsche Taycan 2 Door Tyres and Wheels -> Configuring Tyre Pressure Monitoring (TPM) on the central display User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Tyres and Wheels -> Configuring Tyre Pressure Monitoring (TPM) on the central display for Your Porsche Taycan 2 Door Second Generation (2025-2026)

A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tyres and Wheels
250
or fit the spare wheel.
e Do not continue driving with defective tyres.
Have defective tyres replaced immediately. Visit
a qualified specialist workshop. Porsche recom-
mends a Porsche partner as they have trained
workshop personnel and the necessary parts and
tools.
e Do not drive with tyres in which the tyre pressure
drops again very quickly. In case of doubt, have
tyres checked by a qualified specialist workshop.
Porsche recommends a Porsche partner as they
have trained workshop personnel and the neces-
sary parts and tools.
Faults in the Tyre Pressure Monitoring (TPM)
system
TPM will not function correctly in the following sit-
uations, for example:
– If the Tyre Pressure Monitoring is faulty
– If wheel transmitters for Tyre Pressure Monitor-
ing are missing
– During the learning phase after the tyre settings
have been updated
– After a wheel change without updating the tyre
settings
– If tyre temperatures are too high
Checking the tyre pressure in the instrument
cluster
The individual tyre pressures are only displayed
above a speed of approx. 25 km/h (16 mph) or if the
tyre has been inflated by at least 0.1 bar (1.5 psi).
When the vehicle is turned on after the vehicle has
been stationary for more than approx. 10 minutes,
lines (-.-) will appear instead of the tyre pressures.
e Tyre info e Current press.
> Please refer to chapter "Operating the instru-
ment cluster" on page 129.
The display of the actual pressure is only for infor-
mation. The tyre pressures change depending on the
temperature.
e Under no circumstances should the tyre pres-
sures be changed based on this display.
Checking the pressure deviation in the in-
strument cluster
Fig. 211: Example of pressure difference
bb Vehicle is stationary.
e Tyre info e Pressure deviation
> Please refer to chapter "Operating the instru-
ment cluster" on page 129.
The difference to the required pressure is displayed
on the relevant wheel. Example:
If –0.1 bar (–1.5 psi) is displayed for the rear right
wheel, 0.1 bar (1.5 psi) must be added to this tyre.
The displayed pressures take into account the tyre
temperature.
e Always use the pressure deviation from the dis-
play or from the corresponding tyre pressure
warning to correct the tyre pressure.
Setting tyres
Settings for tyre type, tyre size and load can be ad-
justed via the central display:
> Please refer to chapter "Configuring Tyre Pres-
sure Monitoring (TPM) on the central display" on
page 250.
Configuring Tyre Pressure Moni-
toring (TPM) on the central
display
WARNING
Incorrect settings
Low or high tyre pressure irreparably damages the
tyre and the wheel, lengthens the braking distance
and greatly increases the risk of an accident.
Despite the Tyre Pressure Monitoring system, it is
still the driver’s responsibility to ensure that the
tyres are inflated with the correct tyre pressure and
the vehicle settings are correct. Incomplete or in-
correct settings may affect the accuracy of warnings
and messages.
e Adapt tyre pressure to suit your specific tyres
and the payload.
e Make sure that the settings in the TPM menu
correspond to the tyres fitted on the vehicle and
its payload (especially after a wheel change or
changes in vehicle loading).
e Then select the type and size of fitted tyre again
in the TPM menu, even if the settings for the
newly fitted set of wheels are the same as for the
old wheels.
Accessing filling information
bb Vehicle is stationary.
e
e Setting e Vehicle eTyre pressure
monitoring
Load, tyre type and tyre size settings are displayed:
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Tyres and Wheels
251
If the tyres have not yet been registered dashes (-.-)
are displayed instead of the tyre pressures.
Displaying pressure difference
bb Vehicle is stationary.
e
e Setting e Vehicle eTyre pressure
monitoring e pressure deviation
Displaced are the required pressure and the pressure
deviation from the required pressure for each wheel
along with the load, tyre type and tyre size
information.
Example: If –0.1 bar (–1.5 psi) is displayed for the
rear right wheel, 0.1 bar (1.5 psi) must be added to
this tyre. The displayed pressures take into account
the tyre temperature.
e Always use the pressure deviation from the dis-
play or from the corresponding tyre pressure
warning to correct the tyre pressure.
If the tyres are not yet taught, the new required
pressures are displayed instead of the actual pres-
sure deviations.
Setting tyre type and tyre size
Information
The options available depend on the model and tyre
type. For this reason, some of the selection options
shown here may not be available.
e Before fitting tyres and wheels with dimensions
that are not available for selection in the TPM
menu, the missing information should be added.
Visit a qualified specialist workshop. Porsche
recommends a Porsche partner as they have
trained workshop personnel and the necessary
parts and tools.
e Use only tyres and wheels authorised by Porsche.
e
e Setting e Vehicle eTyre pressure
monitoring e tyre selection
Selecting full load or partial load
e
e Setting e Vehicle eTyre pressure
monitoring e full load
Full load
Full load is activated.
Full load
Partial load is activated.
e Adapt the tyre pressures to the selected load
type.
Information
If the option Full load is not displayed, the specified
tyre pressures are valid for all types of vehicle load.
Teaching in Tyre Pressure Monitoring
Tyre Pressure Monitoring begins to learn the tyres
after a wheel change, wheel transmitter replacement
or update of the tyre settings. During this process,
Tyre Pressure Monitoring recognises the wheels and
their locations. Position and pressure information is
displayed as soon as Tyre Pressure Monitoring has
assigned the wheels recognised as belonging to the
vehicle to the correct wheel positions.
During the learning process, the target pressures for
cold tyres (20 °C) are displayed on the central dis-
play and a message appears on the instrument
cluster.
The tyre pressure warning light
on the instru-
ment cluster remains lit until all the wheels have
been registered.
Inflating tyres
CAUTION
Hot filling hose
The compressor’s filling hose can get hot during the
inflation process and can cause burns.
e Wear gloves.
The compressor is housed in the right-hand box in
the front luggage compartment.
> Please refer to chapter "Luggage compartment"
on page 153.
> Read and follow the operating instructions on the
compressor.
1. Screw the compressor’s filler hose onto the tyre
valve.
2. Connect the compressor to a plug socket in the
vehicle and switch on the compressor.
The tyre is inflated.
3. Check inflation pressure using the pressure
gauge and reduce tyre pressure or add more air if
necessary. Check the inflation pressure again.
4. Switch off compressor.
5. Unscrew the compressor’s filler hose.
Information
The tyre pressure can also be checked at a service
station and the tyres can be inflated.
Reducing inflation pressure
1. Switch off compressor.
2. Open air bleed screw on the filler hose until the
correct inflation pressure is achieved.

Related Topics

Popular Owner Manuals