Get SERVICING AND MAINTENANCE -> Tires and Wheels Guide for Ram Pickup 1500 Light Truck 2023

368 SERVICING AND MAINTENANCE

Side Marker Lamp

FOG LAMPS — IF EQUIPPED

CAUTION!

See the following steps to replace:

1. Open the hood.

Please see an authorized dealer for service on LED and

Halogen front fog lamps.

Do not contaminate the bulb glass by touching it with

your fingers or by allowing it to contact other oily

surfaces. Shortened bulb life will result.

Halogen

2. Disconnect and isolate the negative battery cable.

See the following steps to replace:

3. Locate the side marker lamp, which can be found on

the back side of the headlamps.

1. Reach under and behind the front fascia/bumper to

access the back of the front fog lamp housing.

REAR TAIL/STOP, TURN SIGNAL AND BACKUP

LAMPS

2. Disconnect the fog lamp wiring harness connector

from the fog lamp bulb.

1. Remove the two screws and pushpin retainers that

pass through the bed sheet metal.

Side Marker Lamp

4. Disengage the side marker socket by rotating

counterclockwise a quarter turn.

Fog Lamp Bulb

5. Pull the socket and bulb straight out from the

housing.

Tail Lamp Locations

3. Rotate the bulb counterclockwise a quarter turn to

unlock the bulb from the housing.

1 — Tail Lamp

6. Separate the bulb from the socket without twisting.

2 — Fasteners

4. Pull the bulb straight out from the housing.

7. Reverse the procedure for installation of new bulb

and covers.

3 — Pushpin Retainers

5. Reverse the procedure to install the bulb and cover.

SERVICING AND MAINTENANCE 369

2. Pull the outboard side of the lamp rearward far

enough to unsnap the two receptacles on the

outboard side of the lamp housing from the two

plastic snap post retainers in the outer box side

panel.

4. Rotate the bulb socket counterclockwise a quarter

turn to unlock it from the housing.

2. Separate the connector holding the housing and

wiring harness to the body.

5. Pull the bulb straight out of the socket.

CAUTION!

Do not contaminate the bulb glass by touching it with

your fingers or by allowing it to contact other oily

surfaces. Shortened bulb life will result.

6. Reverse the procedure to install the bulb and

housing.

CENTER HIGH MOUNTED STOP LAMP (CHMSL)

WITH CARGO LAMP

CHMSL Bulb Location

3. Turn the desired bulb socket a quarter turn counter-

clockwise and remove the socket and bulb from

housing.

See the following steps to replace:

Tail Lamp Removal

1. Remove the four screws holding the housing/lens to

the body as shown.

3. Disconnect the wiring harness connectors from the

bulb socket.

4. Pull the desired bulb straight from the socket.

CAUTION!

Do not contaminate the bulb glass by touching it with

your fingers or by allowing it to contract other oily

surfaces. Shortened bulb life will result.

8

 Outside Bulbs: Cargo Lamps

 Inside Bulb: Center High Mounted Stop Lamp

5. Reverse the procedure for installation of bulbs and

housing.

CHMSL Mounting Screw Locations

Wiring Harness Connector

370 SERVICING AND MAINTENANCE

NOTE:

Tire Markings

TIRES

 P (Passenger) — Metric tire sizing is based on US design

standards. P-Metric tires have the letter “P” molded

into the sidewall preceding the size designation.

Example: P215/65R15 95H.

TIRE SAFETY INFORMATION

Tire safety information will cover aspects of the following

information: Tire Markings, Tire Identification Numbers,

Tire Terminology and Definitions, Tire Pressures, and Tire

Loading.

 European — Metric tire sizing is based on European

design standards. Tires designed to this standard have

the tire size molded intothesidewall beginning with the

section width. The letter "P" is absent from this tire size

designation.

Example: 215/65R15 96H.

 LT (Light Truck) — Metric tire sizing is based on US

design standards. The size designation for LT-Metric

tires is the same as for P-Metric tires except for the

letters “LT” that are molded into the sidewall preceding

the size designation.

Tire Markings

1 — US DOT Safety Standards Code

(TIN)

Example: LT235/85R16.

 Temporary spare tires are designed for temporary

emergency use only. Temporaryhigh pressure compact

spare tires have the letter “T” or “S” molded into the

sidewall preceding the size designation.

2 — Size Designation

3 — Service Description

4 — Maximum Load

Example: T145/80D18 103M.

5 — Maximum Pressure

6 — Treadwear, Traction and

Temperature Grades

 High flotation tire sizing is based on US design stan-

dards and it begins with the tire diameter molded into

the sidewall.

Example: 31x10.5 R15 LT.

SERVICING AND MAINTENANCE 371

TIRE SIZING CHART

EXAMPLE:

Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT

P = Passenger car tire size based on US design standards, or

"....blank...." = Passenger car tire based on European design standards, or

LT = Light truck tire based on US design standards, or

T or S = Temporary spare tire or

31 = Overall diameter in inches (in)

215, 235, 145 = Section width in millimeters (mm)

65, 85, 80 = Aspect ratio in percent (%)

 Ratio of section height to section width of tire, or

10.5 = Section width in inches (in)

R = Construction code

 "R" means radial construction, or

 "D" means diagonal or bias construction

15, 16, 18 = Rim diameter in inches (in)

8

Service Description:

95 = Load Index

 A numerical code associated with the maximum load a tire can carry

H = Speed Symbol

 A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions

 The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions

(i.e., tire pressure, vehicle loading, road conditions, and posted speed limits)

372 SERVICING AND MAINTENANCE

Load Identification:

EXAMPLE:

Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire:

 XL = Extra load (or reinforced) tire, or

 LL = Light load tire or

 C, D, E, F, G = Load range associated with the maximum load a tire can carry at a specified pressure

Maximum Load – Maximum load indicates the maximum load this tire is designed to carry

Maximum Pressure – Maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire

Tire Identification Number (TIN)

The Tire Identification Number (TIN) may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN,

including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on

the outboard side, then you will find it on the inboard side of the tire.

EXAMPLE:

DOT MA L9 ABCD 0301

DOT = Department of Transportation

 This symbol certifies that the tire is in compliance with the US Department of Transportation tire safety standards and is approved for highway use

MA = Code representing the tire manufacturing location (two digits)

L9 = Code representing the tire size (two digits)

ABCD = Code used by the tire manufacturer (one to four digits)

SERVICING AND MAINTENANCE 373

EXAMPLE:

03 = Number representing the week in which the tire was manufactured (two digits)

 03 means the 3rd week

01 = Number representing the year in which the tire was manufactured (two digits)

 01 means the year 2001

 Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could represent the 3rd

week of 1981 or 1991

Tire Terminology And Definitions

Term

Definition

B-pillar

The vehicle B-pillar is the structural member of the body located behind the front door.

Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least

three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours. Inflation

pressure is measured in units of psi (pounds per square inch) or kPa (kilopascals).

Cold Tire Inflation Pressure

The maximum inflation pressure is the maximum permissible cold tire inflation pressure for this tire.

The maximum inflation pressure is molded into the sidewall.

Maximum Inflation Pressure

Recommended Cold Tire Inflation Pressure

Tire Placard

The manufacturer’s recommended cold tire inflation pressure as shown on the tire placard.

8

A label permanently attached to the vehicle describing the vehicle’s loading capacity, the original

equipment tire sizes and the recommended cold tire inflation pressures.

374 SERVICING AND MAINTENANCE

This placard tells you important information about the:

1. Number of people that can be carried in the vehicle.

2. Total weight your vehicle can carry.

Tire Loading And Tire Pressure

NOTE:

The proper cold tire inflation pressure is listed on the

driver’s side B-pillar or the rear edge of the driver's side

door.

3. Tire size designed for your vehicle.

4. Cold tire inflation pressures for the front, rear, and

spare tires.

Check the inflation pressure of each tire, including the

spare tire (if equipped), at least monthly and inflate to the

recommended pressure for your vehicle.

Loading

The vehicle maximum load on the tire must not exceed the

load carrying capacity of the tire on your vehicle. You will

not exceed thetire's load carrying capacity if you adhere to

the loading conditions, tire size, and cold tire inflation

pressures specified on the Tire And Loading Information

Placard in Vehicle Loading Ú page 172.

Example Tire Placard Location (B-pillar)

Tire And Loading Information Placard

NOTE:

Under a maximum loaded vehicle condition, Gross Axle

Weight Rating (GAWR) for the front and rear axles must

not be exceeded.

For further information on GAWR, vehicle loading, and

trailer towing Ú page 172.

Example Tire Placard Location (Door)

To determine the maximum loading conditions of your

vehicle, locate the statement “The combined weight of

occupants and cargo should never exceed XXX kg or XXX

lbs” on the Tire And Loading Information Placard. The

combined weight of occupants, cargo/luggage and trailer

tongue weight (if applicable) should never exceed the

weight referenced here.

Tire And Loading Information Placard

SERVICING AND MAINTENANCE 375

Metric Example For Load Limit

Steps For Determining Correct Load Limit—

(5) Determine the combined weight of

luggage and cargo being loaded on the

vehicle. That weight may not safely

exceed the available cargo and luggage

load capacity calculated in Step 4.

For example, if “XXX” amount equals 635 kg and there will

be five 68 kg passengers in your vehicle, the amount of

available cargo and luggage load capacity is 295 kg

(635-340 (5x68) = 295 kg) as shown in step 4.

(1) Locate the statement “The combined

weight of occupants and cargo should

never exceed XXX kg or XXX lbs.” on your

vehicle's placard.

NOTE:

 If your vehicle will be towing a trailer, load from your

trailer will be transferred to your vehicle. The following

table shows examples on how to calculate total load,

cargo/luggage, and towing capacities of your vehicle

with varying seating configurations and number and

size of occupants. This table is for illustration purposes

only and may not be accurate for the seating and load

carry capacity of your vehicle.

(6) If your vehicle will be towing a trailer,

load from your trailer will be transferred

to your vehicle. Consult this manual to

determine how this reduces the

available cargo and luggage load

capacity of your vehicle.

(2) Determine the combined weight of

the driver and passengers that will be

riding in your vehicle.

(3) Subtract the combined weight of the

driver and passengers from XXX kg or

XXX lbs.

 For the following example, the combined weight

of occupants and cargo should never exceed

865 lbs (392 kg).

(4) The resulting figure equals the

available amount of cargo and luggage

load capacity. For example, if “XXX”

amount equals 1400 lbs. and there will

be five 150 lb passengers in your

vehicle, the amount of available cargo

and luggage load capacity is 650 lbs.

(1400-750 (5x150) = 650 lbs.)

8

376 SERVICING AND MAINTENANCE

SERVICING AND MAINTENANCE 377

Ride Comfort And Vehicle Stability

WARNING!

Proper tire inflation contributes to a comfortable ride.

Overinflation produces a jarring and uncomfortable ride.

Overloading of your tires is dangerous. Overloading can

cause tire failure, affect vehicle handling, and increase

your stopping distance. Use tires of the recommended

load capacity for your vehicle. Never overload them.

 Overinflated or underinflated tires can affect vehicle

handling and can fail suddenly, resulting in loss of

vehicle control.

Tire Inflation Pressures

The proper cold tire inflation pressure is listed on the

driver's side B-pillar or rear edge of the driver's side door.

 Unequal tirepressures can cause steering problems.

You could lose control of your vehicle.

At least once a month:

TIRES — GENERAL INFORMATION

 Unequal tire pressures from one side of the vehicle

to the other can cause the vehicle to drift to the right

or left.

 Check and adjust tire pressure with a good quality

pocket-type pressure gauge. Do not make a visual

judgment when determining proper inflation.

Tires may look properly inflated even when they are

underinflated.

Tire Pressure

Proper tire inflation pressure is essential to the safe and

satisfactory operation of your vehicle. Four primary areas

are affected by improper tire pressure:

 Always drive with each tire inflated to the recom-

mended cold tire inflation pressure.

 Inspect tires for signs of tire wear or visible damage.

 Safety

Both underinflation and overinflation affect the stability of

the vehicle and can produce a feeling of sluggish response

or over responsiveness in the steering.

 Fuel Economy

 Tread Wear

CAUTION!

After inspecting or adjusting the tire pressure, always

reinstall the valve stem cap. This will prevent moisture

and dirt from entering the valve stem, which could

damage the valve stem.

NOTE:

 Ride Comfort and Vehicle Stability

Safety

 Unequal tire pressures from side to side may cause

erratic and unpredictable steering response.

WARNING!

 Unequal tire pressure from side to side may cause the

vehicle to drift left or right.

8

Inflation pressures specified on the placard are always

“cold tire inflation pressure”. Cold tire inflation pressure is

defined as the tire pressure after the vehicle has not been

driven for at least three hours, or driven less than 1 mile

(1.6 km) after sitting for a minimum of three hours. The

cold tire inflation pressure must not exceed the maximum

inflation pressure molded into the tire sidewall.

 Improperly inflated tires are dangerous and can

cause collisions.

Fuel Economy

Underinflated tires will increase tire rolling resistance

resulting in higher fuel consumption.

 Underinflation increases tire flexing and can result in

overheating and tire failure.

Tread Wear

 Overinflation reduces a tire's abilityto cushion shock.

Objects on the road and chuckholes can cause

damage that result in tire failure.

Improper cold tire inflation pressures can cause abnormal

wear patterns and reduced tread life, resulting in the need

for earlier tire replacement.

(Continued)

378 SERVICING AND MAINTENANCE

Check tire pressures more often if subject to a wide range

of outdoor temperatures, as tire pressures vary with

temperature changes.

Damaged Run Flat tires, or Run Flat tires that have

experienced a loss of pressure should be replaced

immediatelywith another Run Flat tireof identical sizeand

service description (Load Index and Speed Symbol).

Replace the tire pressure sensor as well as it is not

designed to be reused.

WARNING!

High speed driving with your vehicle under maximum

load is dangerous. The added strain on your tires could

cause them to fail. You could have a serious collision.

Do not drive a vehicle loaded to the maximum capacity

at continuous speeds above 75 mph (120 km/h).

Tire pressures change by approximately 1 psi (7 kPa) per

12°F (7°C) of air temperature change. Keep this in mind

when checking tire pressure inside a garage, especially in

the Winter.

Run Flat Tires — If Equipped

Example: If garage temperature = 68°F (20°C) and the

outside temperature = 32°F (0°C) then the cold tire

inflation pressure should be increased by 3 psi (21 kPa),

which equals 1 psi (7 kPa) for every 12°F (7°C) for this

outside temperature condition.

Run Flat tires allow you the capability to drive 50 miles

(80 km) at 50 mph (80 km/h) after a rapid loss of inflation

pressure. This rapid loss of inflation is referred to as the

Run Flat mode. A Run Flat mode occurs when the tire

inflation pressure is of/or below 14 psi (96 kPa).

Once a Run Flat tire reaches the Run Flat mode it has

limited driving capabilities and needs to be replaced

immediately. A Run Flat tire is not repairable. When a Run

Flat tire is changed after being driven in a Run Flat mode

14psi (96 kPa) condition, please replace the TPMS sensor

as it is not designed to be reused.

Radial Ply Tires

WARNING!

Combining radial ply tires with other types of tires on

your vehicle will cause your vehicle to handle poorly.

The instability could cause a collision. Always use radial

ply tires in sets of four. Never combine them with other

types of tires.

Tire pressure may increase from 2 to 6 psi (13 to 40 kPa)

during operation. DO NOT reduce this normal pressure

build up or your tire pressure will be too low.

Tire Pressures For High Speed Operation

The manufacturer advocates driving at safe speeds and

within posted speed limits. Where speed limits or

conditions are such that the vehicle can be driven at high

speeds, maintaining correct tire inflation pressure is very

important. Increased tire pressure and reduced vehicle

loading may be required for high-speed vehicle operation.

Refer to an authorized tire dealer or original equipment

vehicle dealer for recommended safe operating speeds,

loading and cold tire inflation pressures.

Tire Repair

NOTE:

The TPMS Sensor must be replaced after driving the

vehicle on a flat tire condition.

If your tire becomes damaged, it may be repaired if it

meets the following criteria:

It is not recommended driving a vehicle loaded at full

capacity or to tow a trailer while a tire is in the

Run Flat mode.

 The tire has not been driven on when flat

 The damage is only on the tread section of your tire

(sidewall damage is not repairable)

For more information Ú page 277.

 The puncture is no greater than ¼ of an inch (6 mm)

Consult an authorized tire dealer for tire repairs and

additional information.

SERVICING AND MAINTENANCE 379

Tire Spinning

Life Of Tire

When stuck in mud, sand, snow, or ice conditions, do not

spin your vehicle's wheels above 30 mph (48 km/h) or for

longer than 30 seconds continuously without stopping.

The service life of a tire is dependent upon varying factors

including, but not limited to:

 Driving style

For further information Ú page 329.

 Tire pressure - Improper cold tire inflation pressures

can cause uneven wear patterns to develop across the

tire tread. These abnormal wear patterns will reduce

tread life, resulting in the need for earlier tire

replacement

WARNING!

Fast spinning tires can be dangerous. Forces generated

by excessive wheel speeds may cause tire damage or

failure. A tire could explode and injure someone.

Do not spin your vehicle's wheels faster than 30 mph

(48 km/h) for more than 30 seconds continuously

when you are stuck, and do not let anyone near a

spinning wheel, no matter what the speed.

 Distance driven

Tire Tread

1 — Tread Wear Indicators

 Performance tires, tires with a speed rating of V or

higher, and Summer tires typically have a reduced

tread life. Rotation of these tires per the vehicle

scheduled maintenance is highly recommended

These indicators are molded into the bottom of the tread

grooves. They will appear as bands when the tread depth

becomes 1/16 of an inch (1.6 mm). When the tread is

worn to the tread wear indicators, the tire should be

replaced.

WARNING!

Tread Wear Indicators

Tread wear indicators are in the original equipment tires to

help you in determining when your tires should be

replaced.

Tires and the spare tire should be replaced after six

years, regardless of the remaining tread. Failure to

follow this warning can result in sudden tire failure.

You could lose control and have a collision resulting in

serious injury or death.

For further information Ú page 380.

8

NOTE:

Wheel Valve Stem must be replaced as well when

installing new tires due to wear and tear in existing tires.

Keep dismounted tires in a cool, dry place with as little

exposure to light as possible. Protect tires from contact

with oil, grease, and gasoline.

380 SERVICING AND MAINTENANCE

Replacement Tires

TIRE TYPES

WARNING!

The tires on your new vehicle provide a balance of many

characteristics. They should be inspected regularly for

wear and correct cold tire inflation pressures. The

manufacturer strongly recommends using tires equivalent

to the originals in size, quality and performance when

replacement is needed Ú page 379. Refer to the Tire And

Loading Information Placard or the Vehicle Certification

Label for the size designation of your tire. The Load Index

and Speed Symbol for your tirewill be found on the original

equipment tire sidewall.

All Season Tires — If Equipped

 Do not use a tire, wheel size, load rating, or speed

rating other than that specified for your vehicle.

Some combinations of unapproved tires and wheels

may change suspension dimensions and perfor-

mance characteristics, resulting in changes to

steering, handling, and braking of your vehicle. This

can cause unpredictable handling and stress to

steering and suspension components. You could

lose control and have a collision resulting in serious

injury or death. Use only the tire and wheel sizes with

load ratings approved for your vehicle.

All Season tires provide traction for all seasons (Spring,

Summer, Autumn, and Winter). Traction levels may vary

between different all season tires. All season tires can be

identified by the M+S, M&S, M/S or MS designation on the

tire sidewall. Use all season tires only in sets of four;

failure to do so may adversely affect the safety and

handling of your vehicle.

Summer Or Three Season Tires —

If Equipped

For more information relating totheLoad Index and Speed

Symbol of a tire Ú page 371.

 Never use a tire with a smaller load index or capacity,

other than what was originally equipped on your

vehicle. Using a tire with a smaller load index could

result in tire overloading and failure. You could lose

control and have a collision.

Summer tires provide traction in both wet and dry

conditions, and are notintended tobe driven in snow or on

ice. If your vehicle is equipped with Summer tires, be

aware these tires are not designed for Winter or cold

driving conditions. Install Winter tires on your vehiclewhen

ambient temperatures are less than 40°F (5°C) or if

roads are covered with ice or snow. For more information,

contact an authorized dealer.

It is recommended toreplacethetwo front tires or two rear

tires as a pair. Replacing just one tire can seriously affect

your vehicle’s handling. If you ever replace a wheel, make

sure that the wheel’s specifications match those of the

original wheels.

 Failure to equip your vehicle with tires having

adequate speed capability can result in sudden tire

failure and loss of vehicle control.

It is recommended you contact an authorized tire dealer or

original equipment dealer with any questions you may

have on tire specifications or capability. Failure to use

equivalent replacement tires may adversely affect the

safety, handling, and ride of your vehicle.

Summer tires do not contain the all season designation or

mountain/snowflake symbol on the tire sidewall. Use

Summer tires only in sets of four; failure to do so may

adversely affect the safety and handling of your vehicle.

CAUTION!

Replacing original tires with tires of a different size may

result in false speedometer and odometer readings.

WARNING!

Do not use Summer tires in snow/ice conditions. You

could lose vehicle control, resulting in severe injury or

death. Driving too fast for conditions also creates the

possibility of loss of vehicle control.

SERVICING AND MAINTENANCE 381

Snow Tires

Some areas of the country require the use of snow tires

during the Winter. Snow tires can be identified by a

“mountain/snowflake” symbol on the tire sidewall.

Compact Spare Tire — If Equipped

SPARE TIRES — IF EQUIPPED

The compact spare is for temporary emergency use only.

You can identify if your vehicle is equipped with a compact

spare by looking at the spare tire description on the Tire

And Loading Information Placard located on the driver’s

side door opening or on the sidewall of the tire. Compact

spare tire descriptions begin with the letter “T” or “S”

preceding the size designation. Example: T145/80D18

103M.

NOTE:

For vehicles equipped with Tire Service Kit instead of a

spare tire, please refer to “Tire Service Kit” in “In Case Of

Emergency” for further information.

If you need snow tires, select tires equivalent in

size and type to the original equipment tires.

Use snow tires only in sets of four; failure to do

somay adverselyaffectthe safety and handling

of your vehicle.

CAUTION!

Because of the reduced ground clearance, do not take

your vehicle through an automatic car wash with a

compact or limited use temporary spare installed.

Damage to the vehicle may result.

T, S = Temporary Spare Tire

Snow tires generally have lower speed ratings than what

was originally equipped with your vehicle and should not

be operated at sustained speeds over 75 mph

(120 km/h). For speeds above 75 mph (120 km/h) refer

to original equipment or an authorized tire dealer for

recommended safe operating speeds, loading and cold

tire inflation pressures.

Since this tire has limited tread life, the original equipment

tire should be repaired (or replaced) and reinstalled on

your vehicle at the first opportunity.

For restrictions when towing with a spare tire designated

for temporary emergency use Ú page 179.

Do not install a wheel cover or attempt to mount a

conventional tire on the compact spare wheel, since the

wheel is designed specifically for the compact spare tire.

Do not install more than onecompact spare tireand wheel

on the vehicle at any given time.

Spare Tire Matching Original Equipped Tire

And Wheel — If Equipped

While studded tires improve performance on ice, skid and

traction capability on wet or dry surfaces may be poorer

than that of non-studded tires. Some states prohibit

studded tires; therefore, local laws should be checked

before using these tire types.

Your vehicle may be equipped with a spare tire and wheel

equivalent in look and function to the original equipment

tire and wheel found on the front or rear axle of your

vehicle. This spare tire may be used in the tire rotation for

your vehicle. If your vehicle has this option, refer to an

authorized tire dealer for the recommended tire rotation

pattern.

WARNING!

Compact and collapsible spares are for temporary

emergency use only. With these spares, do not drive

more than 50 mph (80 km/h). Temporary use spares

have limited tread life. When the tread is worn to the

tread wear indicators, the temporary use spare tire

needs to be replaced. Be sure to follow the warnings,

which apply to your spare. Failure to do so could result

in spare tire failure and loss of vehicle control.

8

382 SERVICING AND MAINTENANCE

Collapsible Spare Tire — If Equipped

The collapsiblespare is for temporaryemergency useonly.

You can identify if your vehicle is equipped with a

collapsible spare by looking at the spare tire description

on the Tire And Loading Information Placard located on

the driver’s side door opening or on the sidewall of the tire.

Limited Use Spare — If Equipped

WARNING!

The limited use spare tire is for temporary emergency use

only. This tire is identified by a label located on the limited

use spare wheel. This label contains the driving limitations

for this spare. This tire may look like the original equipped

tire on the front or rear axle of your vehicle, but it is not.

Installation of this limited use spare tire affects vehicle

handling. Since it is not the same as your original

Compact and Collapsible spares are for temporary

emergency use only. With these spares, do not drive

more than 50 mph (80 km/h). Temporary use spares

have limited tread life. When the tread is worn to the

tread wear indicators, the temporary use spare tire

needs to be replaced. Be sure to follow the warnings,

which apply to your spare. Failure to do so could result

in spare tire failure and loss of vehicle control.

Collapsible spare tire description

example: 165/80-17 101P.

equipment tire, replace (or repair) the original equipment

tire and reinstall on the vehicle at the first opportunity.

Since this tirehas limited tread life, the original equipment

tire should be repaired (or replaced) and reinstalled on

your vehicle at the first opportunity.

WARNING!

Full Size Spare — If Equipped

Inflate collapsible tire only after the wheel is properly

installed to the vehicle. Inflate the collapsible tire using

the electric air pump before lowering the vehicle.

Limited use spares are for emergency use only.

The full size spare is for temporary emergency use only.

This tire may look like the originally equipped tire on the

front or rear axle of your vehicle, but it is not. This spare

tire may have limited tread life. When the tread is worn to

the tread wear indicators, the temporary use full size

spare tire needs to be replaced. Since it is not the same as

your original equipment tire, replace (or repair) theoriginal

equipment tire and reinstall on the vehicle at the first

opportunity.

Installation of this limited use spare tire affects vehicle

handling. With this tire, do not drive more than the

speed listed on the limited use spare wheel. Keep

inflated to the cold tire inflation pressures listed on your

Tire And Loading Information Placard located on the

driver’s side B-pillar or the rear edge of the driver’s side

door. Replace (or repair) the original equipment tire at

the first opportunity and reinstall it on your vehicle.

Failure to do so could result in loss of vehicle control.

Do not install a wheel cover or attempt to mount a

conventional tire on the collapsible spare wheel, since the

wheel is designed specifically for the collapsible spare tire.

SERVICING AND MAINTENANCE 383

NOTE:

WHEEL AND WHEEL TRIM CARE

CAUTION!

If you intend parking or storing your vehicle for an

extended period after cleaning the wheels with wheel

cleaner, drive your vehicle and apply the brakes to remove

the water droplets from the brake components. This

activity will remove the red rust on the brake rotors and

prevent vehicle vibration when braking.

All wheels and wheel trim, especially aluminum and

chrome plated wheels, should be cleaned regularly using

mild (neutral Ph) soap and water to maintain their luster

and to prevent corrosion. Wash wheels with the same

soap solution recommended for the body of the vehicle

and remember to always wash when the surfaces are not

hot to the touch.

Avoid products or automatic car washes that use acidic

solutions or strong alkaline additives or harsh brushes.

Many aftermarket wheel cleaners and automatic car

washes may damage the wheel's protective finish. Such

damage is not covered by the New Vehicle Limited

Warranty. Only car wash soap, Mopar® Wheel Cleaner

or equivalent is recommended.

Dark Vapor Chrome, Black Satin Chrome, or Low Gloss

Clear Coat Wheels

Your wheels are susceptible to deterioration caused by

salt, sodium chloride, magnesium chloride, calcium

chloride, etc., and other road chemicals used to melt ice

or control dust on dirt roads. Use a soft cloth or sponge

and mild soap to wipe away promptly. Do not use harsh

chemicals or a stiff brush. They can damage the wheel’s

protective coating that helps keep them from corroding

and tarnishing.

CAUTION!

When cleaning extremely dirty wheels including excessive

brake dust, care must be taken in the selection of tire and

wheel cleaning chemicals and equipment to prevent

damage to the wheels. Mopar® Wheel Treatment or

Mopar® Chrome Cleaner or their equivalent is

recommended or select a non-abrasive, non-acidic

cleaner for aluminum or chrome wheels.

If your vehicle is equipped with these specialty wheels,

DO NOT USE wheel cleaners, abrasives, or polishing

compounds. They will permanently damage this finish

and such damage is not covered by the New Vehicle

Limited Warranty. HAND WASH ONLY USING MILD SOAP

AND WATER WITH A SOFT CLOTH. Used on a regular

basis; this is all that is required to maintain this finish.

CAUTION!

Do not use scouring pads, steel wool, a bristle brush,

metal polishes or oven cleaner. These products may

damage the wheel's protective finish. Such damage is

not covered by the New Vehicle Limited Warranty. Only

car wash soap, Mopar® Wheel Cleaner or equivalent is

recommended.

8

384 SERVICING AND MAINTENANCE

SNOW TRACTION DEVICES

Use of traction devices require sufficient tire-to-body clearance. Due to limited clearance, the following snow traction devices are recommended. Follow these recommendations to

guard against damage:

 Snow traction device must be of proper size for the tire, as recommended by the snow traction device manufacturer.

 No other tire sizes are recommended for use with the snow traction device.

 Please follow the table for the recommended tire size, axle and snow traction device:

Snow Traction Device

(Maximum Projection BeyondTire Profile

Or Equivalent)

4x2 (2WD)

Trim Level

Axle

Rear

Tire/Wheel Size

HFE

Tradesman

Bighorn Lonestar

Laramie

275/65R18

275/55R20

S Class

Longhorn

Sport

Rear

275/55R20

Limited

REBEL

Not Chainable

SERVICING AND MAINTENANCE -> Tires and Wheels for Your Ram Pickup 1500 Light Truck 2023

Related Topics

INTRODUCTION

GETTING TO KNOW YOUR VEHICLE

GETTING TO KNOW YOUR INSTRUMENT PANEL

STARTING AND OPERATING

MULTIMEDIA

SAFETY

IN CASE OF EMERGENCY

SERVICING AND MAINTENANCE

TECHNICAL SPECIFICATIONS

CUSTOMER ASSISTANCE