Get Maintenance Guide for Renault Scenic 4 Door Fifth Generation (2023-2026)

ACCESSING THE ENGINE, LEVELS

Do not press down on

the bonnet as there is a

risk that the bonnet

In the event of even a

slight impact involving

the radiator grille or

Bonnet

Unlocking the bonnet catch

may accidentally close.

bonnet, have the bon-

net lock checked by an ap-

proved Dealer as soon as possi-

ble.

5

To open, pull the handle 1 located on

the left-hand side of the dashboard.

Raise the bonnet by several cen-

timetres and push the lever 2 to the

left.

Do not do any work un-

der the bonnet when

the vehicle is charging

or when the ignition is

switched on.

M a i n t e n a n c e - 3 3 7

ACCESSING THE ENGINE, LEVELS

Opening the bonnet

Closing the bonnet

The vehicle drive sys-

tem in an electric vehi-

cle uses a direct volt-

age of approximately

400 volts.

This system can get hot during

and after switching off the igni-

tion.

Respect warning messages giv-

en on the labels in the vehicle.

Any intervention or modifica-

tion on the vehicle's 400 V elec-

trical system (components, ca-

bles, connectors, traction bat-

tery) is strictly prohibited.

The risk of serious burns or elec-

tric shocks can lead to death.

The engine cooling fan may al-

so start at any moment. The

5

After raising the bonnet and disen-

gaging the strut 4 from its mounting

3 , for your safety you must position

the strut in its placement 5 .

Before closing the bonnet, make

sure that nothing has been left in the

engine compartment.

To close the bonnet, re-engage the

strut 4 in its mounting 3 . Hold the

middle of the bonnet and guide it

down to one foot (30 cm) above the

closed position, then release. It will

latch automatically under its own

weight.

label in the engine com-

partment reminds you of this.

Risk of injury.

3 3 8 - M a i n t e n a n c e

ACCESSING THE ENGINE, LEVELS

ground. For each reservoir, the level

when cold must be between the "MI-

NI" and "MAXI" marks on the coolant

reservoirs1 and 2 .

Top this level up when cold before

the “MINI” mark is reached.

Note: for a new vehicle in the running

in phase: the fluid level may be high-

er than the "MAXI" mark on the

reservoir, then drop between the lev-

el "MINI" and "MAXI". This does not

present a risk.

Coolant level

When working in the

engine compartment,

ensure that the wind-

screen wiper stalk is in

Coolant level

the park position.

Risk of injury.

Ensure that the bonnet

is properly locked.

Ensure that nothing is

preventing locking

5

If there is an abnormal or

repeated drop in the fluid

level, consult an approved

dealer.

(grit, cloths, etc.).

After any procedure in

the engine compart-

ment, make sure that

you do not forget any-

Depending on the vehicle, the loca-

tion of the coolant reservoirs may

vary:

– reservoir 1 is used to cool the en-

gine;

No operations should

be carried out on the

cooling circuit when

the engine is hot.

thing (cloth, tools, etc.).

Otherwise, this may lead to en-

gine damage or cause a fire.

or

Risk of burns.

– reservoir 1 is used to cool the en-

gine and reservoir 2 is used to cool

the traction battery;

or

– reservoir 2 is used to cool the en-

gine and the traction battery.

The level should be read with the en-

gine switched off and on level

M a i n t e n a n c e - 3 3 9

ACCESSING THE ENGINE, LEVELS

If the level needs to be topped up,

Levels, filters

only use products approved by our

Technical Department which en-

sure:

The vehicle drive sys-

tem in an electric vehi-

cle uses a direct volt-

age of approximately

Brake fluid level

– antifreeze protection;

– anti-corrosion protection of the

cooling system.

Replacement intervals

Refer to the maintenance document

for your vehicle.

400 volts.

This system can get hot during

and after switching off the igni-

tion.

Respect warning messages giv-

en on the labels in the vehicle.

Any intervention or modifica-

tion on the vehicle's 400 V elec-

trical system (components, ca-

bles, connectors, traction bat-

tery) is strictly prohibited.

5

Do not do any work un-

der the bonnet when

the vehicle is charging

or when the ignition is

switched on.

The risk of serious burns or elec-

tric shocks can lead to death.

The engine cooling fan may al-

so start at any moment. The

The level should be read with the en-

gine switched off and on level

ground. This should be checked fre-

quently, and immediately if you no-

tice even the slightest loss in braking

efficiency.

When working in the

engine compartment,

ensure that the wind-

screen wiper stalk is in

the park position.

label in the engine com-

partment reminds you of this.

Risk of injury.

Replacement intervals

Risk of injury.

Refer to the maintenance document

for your vehicle.

Frequency of checking coolant level

Check the coolant levels regularly

(very severe damage is likely to be

caused to the engine and battery if

there is insufficient coolant).

3 4 0 - M a i n t e n a n c e

ACCESSING THE ENGINE, LEVELS

Windscreen washer reservoir

If there is an abnormal or

repeated drop in the fluid

level, consult an approved

dealer.

Topping up

After any operation on the hydraulic

circuit, a specialist must replace the

fluid. Only use fluids approved by our

Technical Department (and taken

from a sealed container).

5

Level 2

It is normal for the level to drop as

the brake shoes become worn, but it

must never drop lower than the

warning line "MINI".

If you wish to check the disc wear

yourself, you should obtain the docu-

ment explaining the checking proce-

dure from our Network or from the

manufacturer’s website.

Topping up

Open the cap 3 , fill until you can see

the fluid, then refit the cap.

Fluid

Only use windscreen washer fluid

containing antifreeze.

We advise you to consult an ap-

proved dealer or a qualified profes-

sional.

Note: Do not use hard water (risk of

damage to the priming pump,

limescale building up on the pump

and the jets).

M a i n t e n a n c e - 3 4 1

BATTERY

Maintenance/replacement

The vehicle drive sys-

tem in an electric vehi-

cle uses a direct cur-

rent of approximately

12 V battery

The 12 V battery charge level 1 may

decrease, especially if you use your

vehicle:

– when the outside temperature

drops;

– after extended use of energy-con-

suming devices with the engine

switched off.

"400 V".

This system can get hot during

and after switching off the igni-

tion.

Respect warning messages giv-

en on the labels in the vehicle.

Any operation or modification

on the vehicle's 400 V electrical

system (components, cables,

connectors, traction battery) is

strictly prohibited.

The risk of serious burns or elec-

tric shocks can lead to death.

The engine cooling fan may al-

so start at any moment. The

For your own safety

and to ensure the prop-

er operation of the

5

vehicle's electrical

equipment (lights, windscreen

wipers, braking assistance,

etc.), any operation on the 12 V

battery (removal, disconnec-

tion, etc.) must be performed by

a qualified specialist.

Risk of serious burns or electric

shocks.

You must respect the replace-

ment intervals (without exceed-

ing them) as stated in the main-

tenance document.

The 12 V battery supplies the energy

required to operate vehicle equip-

ment (lights, windscreen wipers, au-

dio system, etc.) and certain safety

systems such as the braking assis-

tance.

warning in the engine

compartment reminds you of

this.

You should not open it or add any

fluid.

Risk of injury.

Do not do any work un-

der the bonnet when

the vehicle is charging

or when the ignition is

switched on.

The battery is a specific type.

Please ensure it is replaced with

the same type.

Call an approved Dealer.

3 4 2 - M a i n t e n a n c e

BATTERY

Label A

Breakdown recovery

To avoid damaging your

vehicle, do not recharge

the 12 V battery using:

– an external battery charger;

– a battery from another vehi-

cle.

Call an approved Dealer.

5

It is prohibited to dis-

connect the 12 V bat-

tery.

Observe the indications on the bat-

tery.

Risk of serious burns or

electric shocks.

2. Naked flames and smoking are

forbidden.

3. Eye protection required.

4. Keep away from children.

5. Explosive materials.

Do not use your electric

vehicle to restart the 12 V

battery in another vehicle.

The 12 V electric power of an

electric vehicle is not enough to

perform such an operation.

Risk of damage to the vehicle.

6. Refer to the manual.

7. Corrosive substances.

M a i n t e n a n c e - 3 4 3

CLEANING

ucts). Rinse thoroughly beforehand

using a jet washer:

– spots of tree resin and industrial

pollution;

– mud in the wheel arches and un-

derneath the body which forms

damp patches;

Observe local regulations about

washing vehicles (e.g. do not wash

your vehicle on a public highway).

When washing the vehicle with a

high-pressure cleaning device,

please take the following precau-

tions:

– make sure that your vehicle's

paintwork, the area or the compo-

nent that you want to clean is com-

patible with this type of washing;

– the pressure delivered by the de-

vice must be less than 100 bar;

– when washing, position the spray

nozzle at least 15 cm from the vehicle

and check that the water flow rate is

less than 3.30 gal (15 l)/min);

– do not persist in washing the same

area, impacted points or the seals

(risk of damage to the paint, seals

becoming detached, etc.).

If mechanical components, hinges,

etc. have been cleaned, they must

be protected again by spraying with

products approved by our Technical

Department.

Bodywork maintenance

A well-maintained vehicle will last

longer. It is therefore recommended

to maintain the exterior of the vehi-

cle regularly.

Your vehicle has been treated with

very effective anti-corrosion prod-

ucts. It is nevertheless subject to var-

ious outside influences.

Corrosive agents in the atmosphere

– atmospheric pollution (in built-up

and industrial areas);

– saline atmospheres (near the sea,

particularly in hot weather);

– seasonal and damp climatic con-

ditions, (e.g.: road salt in winter, wa-

ter from road cleaners, etc.).

Minor impacts

Abrasive action

–

bird droppings, which cause a

chemical reaction with the paint

that rapidly discolours paintwork

and may even cause the paint to

peel off.

5

Wash the vehicle immediately to re-

move these marks as it is impossible

to remove them by polishing;

– salt, particularly in the wheel arch-

es and underneath the body after

driving in areas where the roads

have been gritted.

Withdraw the vegetable falls (resin,

film etc.) from the vehicle regularly.

Observe the vehicle stopping dis-

tances when driving on gravelled

surfaces to prevent paint damage.

Dust and sand in the air, mud, road

grit thrown up by other vehicles, etc.

You should take a number of minor

precautions in order to safeguard

your vehicle against such risks.

Repair, or have repaired quickly, ar-

eas where the paint has been dam-

aged, to prevent corrosion spread-

ing.

You should do the following

Remember to visit the body shop pe-

riodically in order to maintain your

anti-corrosion warranty. Refer to the

maintenance document.

Wash your car frequently, with the

engine off, with cleaning products

recommended by our Technical De-

partment (never use abrasive prod-

3 4 4 - M a i n t e n a n c e

CLEANING

– mechanical components (e.g. en-

gine compartment);

– wheels (e.g. braking system com-

ponents such as brake callipers);

– the underbody;

– the parts with hinges (e.g. inside

the doors);

– the painted plastic external fit-

tings (e.g. bumpers).

We have selected special

products to care for your

vehicle and you can ob-

Washing the vehicle

Never wash the engine

compartment, the

tain these from the

manufacturer's accessory out-

lets.

charging connection or

the traction battery with a high-

pressure jet.

This risks damaging the electric

circuit.

Never wash the vehicle while it

is charging.

Risk of electric shock and a risk

to life.

Doing this could give rise to corro-

sion or operational faults.

Do not do the following

Wash the vehicle in bright sunlight or

freezing temperatures.

Do not scrape off mud or dirt without

pre-wetting.

Allow dirt to accumulate on the exte-

rior.

Allow rust to form following minor

impacts.

5

Using a roller type car wash

Return the wiper stalk to the Park

position ꢀ 163.

Check the mounting of external ac-

cessories, additional lights and rear

view mirrors, and ensure that the

wiper blades are secured with adhe-

sive tape.

Remove the radio aerial mast if your

vehicle is fitted with this equipment.

Cleaning the headlights, sensors

and cameras

Use a soft cloth or cotton wool.

If this is not sufficient, moisten the

cloth with soapy water, always rins-

ing with a soft cloth or cotton wool.

Using solvents not approved by our

Technical Department to remove

stains may damage the paintwork.

Finally, carefully dry off with a soft

dry cloth.

Do not use cleaning products con-

taining alcohol or utensils (e.g. a

scraper).

Do not drive in snow or muddy condi-

tions without washing the vehicle,

particularly under the wheel arches

and body.

Remember to remove the adhesive

and refit the aerial (by screwing it in

fully) once the wash is finished.

Cleaning stickers, decorative

films, etc.

Degrease or clean using high-pres-

sure cleaning equipment or by

spraying products not approved by

our Technical Department:

You should do the following

Use a soft cloth or cotton wool.

M a i n t e n a n c e - 3 4 5

CLEANING

Moisten it slightly with soapy water

then always wipe clean with a soft

cloth or cotton wool.

Finally, carefully dry off with a soft

dry cloth.

Rinse and wipe up excess water.

Multimedia screen

Textiles (seats, door trim, etc)

Vacuum-clean the textiles regularly.

Liquid stain

Use soapy water.

Dab lightly (never rub) with a soft

cloth, rinse and remove the excess.

Solid or pasty stain

Carefully remove the excess solid or

pasty material immediately using a

spatula (working from the edges to

the centre to avoid spreading the

stain).

In the case of a liquid stain, clean as

indicated.

Special instructions for sweets or

chewing gum

Place an ice cube on the stain to so-

lidify it then proceed as for a solid

stain.

Maintenance of the screen may de-

pend on the type of multimedia

equipment. Please refer to the multi-

media instructions for further infor-

mation.

Do not do the following

Use alcohol-based cleaning prod-

ucts.

Use utensils (e.g. a scraper).

Rub too hard.

Glass instrument panel

(e.g. instrument panel, clock, exterior

temperature display, etc.).

Use a soft cloth or cotton wool.

If this does not clean them properly,

use a soft cloth (or cotton wool)

slightly moistened with soapy water

and then wipe clean using another

soft damp cloth or cotton wool.

Finally, dry off carefully with a soft

dry cloth.

Do not use products containing al-

cohol and/or spray fluids on the

area.

5

Wash the vehicle using a high-pres-

sure cleaning device.

Interior trim maintenance

A well-maintained vehicle will last

longer. It is therefore recommended

to maintain the interior of the vehi-

cle regularly.

A stain should always be dealt with

swiftly.

Whatever the type of stain, use cold

(or tepid) soapy water prepared

with natural soap.

Detergents (washing-up liquid, pow-

dered products, alcohol-based

products) should not be used.

For further recommenda-

tions on maintaining the

interior and/or in the

Seat belts

event of unsatisfactory results,

please consult an approved

dealer.

These must be kept clean.

Use products selected by our Tech-

nical Department (approved outlets)

or warm, soapy water and a sponge

and wipe with a dry cloth.

Detergents or dyes must not be used

under any circumstances.

Use a soft cloth.

3 4 6 - M a i n t e n a n c e

CLEANING

ponents in the vehicle, or have other

detrimental effects.

Removal/replacing removable

equipment originally fitted in the

vehicle

If you need to remove equipment in

order to clean the passenger com-

partment (for example, mats), al-

ways ensure that they are correctly

refitted and are the right way

around (the driver's mat should be

fitted on the driver's side, etc.) and fit

them with the components supplied

with the equipment (for example,

the driver mat should always be

fixed using the pre-fitted mounting

components).

5

With the vehicle stationary, always

ensure that nothing will impede dri-

ving (anything obstructing the ped-

als, heel wedged by the mat etc.).

Do not do the following

Position objects such as deodorants,

scents etc. near air vents as this

could damage your dashboard trim.

Use high-pressure cleaning equip-

ment or sprays inside the passenger

compartment:

without careful use, this equipment

could impair the correct functioning

of the electrical or electronic com-

M a i n t e n a n c e - 3 4 7

Maintenance for Your Renault Scenic 4 Door Fifth Generation (2023-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals