Get Safety Guide for Seat Ateca SUV First Generation (2016-2020)

Emergencies

3. Remove the lid, levering it with the flat

Rear bulbs (in the side panel)

Note

side of a screwdriver into the recess

Due to the difficulty of accessing fog light

bulbs, have them replaced at a Technical

Service or specialised workshop.

››› Fig. 114

4. Remove the bulb connector.

5. Unscrew the light securing bolt by hand

or using a screwdriver››› Fig. 114

6. Remove the light from the body, gently

pulling it toward you, and place on a

clean, smooth surface.

Change the rear bulbs

Overview of tail lights

7. Disassemble the bulb holder unlocking

the securing tabs››› Fig. 115

8. Change the damaged bulb.

Tail lights on side panel

Fig. 114 Boot: access to the bolt securing the

Turn signal

PY21W NA LL

P21W LL

tail light unit.

9. To refit follow the steps in reverse order,

taking special care when fitting the bulb

holder. The securing tabs must click into

place.

Side light and brake light

Tail lights on the rear lid

Left side

CAUTION

Side lights

P21W LL

W16W

Take care when removing the rear light unit

to make sure there is no damage to the

paintwork or any of its components.

Fog light/side light

Reverse light

Note

Right side

Fig. 115 Retaining tabs on reverse side of tail

●

Make sure you have a soft cloth ready to

place under the glass on the rear light unit,

to avoid any scratches.

Side lights

2x P21W LL

W16W

light.

Reverse light

Follow the steps indicated:

●

In the case of LED lights, change only the

turn signal bulb.

The table corresponds to a right-hand traffic

vehicle. The position of lights may vary ac-

cording to the country.

Check which of the bulbs is defective.

2. Open the rear lid.

100

Fuses and bulbs

2. Unlock the securing tabs from the bulb

Rear lights (in the rear lid)

Fig. 116 Rear lid open: remove the lid.

Fig. 117 Remove the bulb holder.

Changing number plate light bulbs

holder››› Fig. 117

or turn the bulb

holder to the left

and

3. Remove the bulb holder from its location.

4. Lightly press the defective bulb into the

bulb holder, then turn it to the left and re-

move it.

5. Fit the new bulb, pressing it into the bulb

holder and turn it to the right as far as it

will go.

6. Use a cloth to remove any fingerprints

from the glass part of the bulb.

7. Check that the new bulb works properly.

8. Carry out the same actions in reverse or-

der for assembly and pay special atten-

tion to placing the bulb holder, ensuring

that the tabs are properly secured.

Fig. 118 In the rear bumper: number plate

light.

Note

For LED pilots, you can only change the re-

verse bulb.

Fig. 119 Number plate light: detach the bulb

holder.

The rear lid must be open to change the

bulbs.

Follow the steps indicated:

Press the number plate light in the direc-

Remove the rear lid cover in the direction

indicated››› Fig. 116.

tion of the arrow››› Fig. 118.

2. Remove the number plate light.

101

Emergencies

Side turn signals

3. Turn the connector lock››› Fig. 119 in the

direction of arrow

connector.

and pull on the

4. Rotate the bulb holder in the direction of

arrow

and extract it with the bulb.

5. Replace the defective bulb with a new

bulb with the same features.

6. Insert the bulb holder in the number

plate light and turn in the opposite direc-

tion of arrow

until it stops.

7. Plug the connector into the bulb holder.

Fig. 120 Turn signal integrated in the rear view

Note

mirror

Depending on how equipped the vehicle is,

the number plate lights may be LEDs. LEDs

have an estimated life that exceeds than

that of the car. If a light with LEDs fails, go

to an authorised workshop for replace-

ment.

The side turn signals are LEDS and are inte-

grated in the exterior mirrors.

In case of failure, go to an authorised work-

shop to have them replaced.

102

Safety for Your Seat Ateca SUV First Generation (2016-2020)

Related Topics

Popular Owner Manuals

Latest Owner Manuals