Get Dash panel -> Digital instrument panel display Guide for Seat Ibiza SUV Fourth Generation (2009-2017)

Operation

–

If any of both turn signals fails, the warning

lamp will start flashing twice faster than nor-

mal.

To set the minutes, press button

again

Digital instrument panel

display

and select the minute option. Set from but-

ton

“set”.

For further information on the turn signals,

please see ››› page 93.

Once the operation has been carried out, the

system memorises the time.

Fuel gauge  and reserve indicator

“SAFE” Electronic immobiliser*

Recommended gear display*

This warning lamp flashes if an unauthorised

key is used.

Inside the key there is a chip that deactivates

the electronic immobiliser automatically

when the key is inserted into the ignition.

The electronic immobiliser will be activated

again automatically as soon as you pull the

key out of the ignition lock.

Fig. 72 Instrument panel: fuel gauge

The fuel tank has a capacity of approx. 45 li-

tres.

If the following message* is shown on the in-

strument panel display: SAFE, the vehicle

cannot be started.

Fig. 73 Gear display.

When the gauge reaches the reserve area,

››› Fig. 72 the warning lamp will light up and

an acoustic signal will sound at the same

time, reminding the driver to refuel. At this

point there are still 7 litres of fuel in the tank.

The engine can, however, be started if the

appropriate coded SEAT genuine key is used.

Use the gear display to save fuel. If you are

not in the correct gear, a triangle will appear

next to the gear display indicating whether

you should change up or down ››› Fig. 73. For

further information on the gear change dis-

play, please see the ››› page 134.

Note

The vehicle cannot operate properly if you do

not have a genuine SEAT key.

Digital clock*

Note

–

To set the hour, press button

››› Fig. 70.

The gear change indication should not be tak-

en into account when quick acceleration is re-

quired (for example when overtaking).

The “hour” option flashes on the digital

display and is set using button

“set”

››› Fig. 70.

Dash panel

●

The trip memory 1 collects the travel and

consumption rates from the moment the igni-

tion is switched on until it is switched off. If

the journey is continued within two hours of

switching off the ignition, the new values will

be added to the existing trip recorder memo-

ry. The memory will automatically be deleted

if the journey is interrupted for more than 2

hours.

Speed warning

Multi-function display (MFI)*

km/h - Driving speed

Driving speed is digitally shown in the dis-

play.

min - Journey duration

The display shows the amount of time which

has elapsed since the ignition was switched

on.

The total memory 2 collects the trip data for

any number of individual journeys (even if

the ignition is switched off for longer than

two hours) up to a total of 19 hours and 59

minutes travel time or 1,999 km distance

travelled. The memory will automatically be

deleted if one of the named values is

reached.

The maximum display value in both memo-

ries is 19 hours and 59 minutes. The memory

will automatically be deleted once this value

has been reached.

Fig. 74 Windscreen wiper lever: button

and rocker switch

The multifunction display (MFI) shows you in-

formation on the journey and fuel consump-

tion. It has two automatic memories: 1 - Trip

memory and 2 - Total memory. The selected

memory will be shown in the upper right-

hand corner of the display.

Ø km/h (mph) - Average speed

After turning on the ignition, the average

speed will be shown after travelling a dis-

tance of approximately 100 metres. Until

then dashes will appear in the display. The

display will be updated every 5 seconds

while the vehicle is in motion.

You can switch between the following dis-

plays in the multi-function display (MFI) by

operating rocker switch ››› Fig. 74

windscreen wiper lever:

on the

Selecting a memory

Memory displays

–

With the ignition switched on, briefly press

●

Driving speed

button ››› Fig. 74

on the window wiper

km (miles) - Distance travelled

lever to move from one memory to another.

Journey duration

The display shows the distance travelled

since the ignition was switched on.

Average speed

Resetting a memory

Distance

The maximum display value in both memo-

ries is 1,999 km. The memory will automati-

cally be deleted once this value has been

reached.

–

Select the memory that you would like to

reset.

Operating range

Average fuel consumption

Current fuel consumption

Outside temperature indicator

Press and hold button

on the window

wiper lever for at least 2 seconds.

Operation

RESET

. The set

 Km (miles) - Fuel range

and press button ››› Fig. 74

WARNING

speed is memorised. If the indicated speed is

exceeded at any time, a warning message is

displayed on the screen and an audible warn-

ing sounds.¹⁾

The fuel range is calculated using the figures

for tank content and current fuel consump-

tion. This shows how far the vehicle can trav-

el using the same conditions as a reference.

There could be black ice on the road surface

even if the “snowflake symbol” is not shown.

For this reason you should not rely exclusive-

ly on this display - Risk of accident!

This may be deactivated by pressing the

Ø l/100 km - Average fuel consumption

RESET

button. The speed may be altered us-

Note

ing the rocker switch ››› Fig. 74

in intervals

After turning on the ignition, average fuel

consumption will be shown after travelling

approximately 100 metres. Until then dashes

will appear in the display. The display will be

updated every 5 seconds while the vehicle is

in motion. The amount of fuel used will not

be shown.

When the vehicle is at a standstill or when

travelling at very low speeds, the tempera-

ture displayed may be higher than the true

outside temperature as a result of the heat

produced by the engine.

of 5 km/h within 5 seconds of the initial

memory value being stored.

Outside temperature display

The measurement margin ranges from -45 °C

(-49 °F) to +58 °C (+136 °F). At temperatures

lower than +4°C (+39 °F), an “ice crystal sym-

bol” is displayed and a “warning” is sounded

if the vehicle is moving at more than 10 km/h

(6 mph) (ice warning). This symbol will flash

for about 10 seconds and remains lit until

the outside temperature rises above +4°C

(+39°F), or if you are driving, the temperature

does not rise above +6°C (+43°F) if it was al-

ready lit.

Selector lever position display*

l/100 km o l/h - Current fuel consumption

The display will show the current fuel con-

sumption in ltr/km whilst the vehicle is in

motion or in ltr/hour when the vehicle is at a

standstill with the engine running.

Using this display you can see how your driv-

ing style affects fuel consumption

››› page 134.

The lighting of the ice crystal symbol is in-

tended to warn the driver of the risk of ice,

so that he/she proceeds with due care.

Indicated speed warning

When the required speed has been reached,

enter the “Speed warning” mode in the menu

Fig. 75 Digital display: Gearbox lever position

for automatic gearbox.

Depending on the model version, the message on

the screen may vary and may be represented by the

flashing of the speed indicator or by a speed mes-

sage.

Dash panel

The position of the automatic selector lever

will be shown on the display ››› page 129.

spection Service). The service interval display

only indicates the dates of services that in-

clude engine oil change. The dates of all oth-

er services, such as Inspection Service or

brake fluid change, appear in the sticker on

the door pillar or in the Maintenance Pro-

gramme.

The instrument panel display will show the

“spanner symbol”  and the “km (miles)”

indication, along with a clock symbol with

the days remaining until the date of the next

service. The figure indicated is the maximum

number of kilometres (miles) remaining be-

fore the date of the next service. The indica-

tion changes after a few seconds. A “clock

symbol” appears and the number of days un-

til the service appointment should be carried

out.

Odometer

The upper counter in the display registers the

total mileage covered by the vehicle.

Vehicles with service intervals dependent on

time/distance travelled already have certain

service intervals set.

The lower counter registers the short jour-

neys. The last digit indicates 100-metre sec-

tions. The trip recorder counter may be reset

The intervals are calculated separately in ve-

hicles with LongLife service. Technical pro-

gress has made it possible to considerably

reduce servicing requirements. With the

LongLife System, SEAT ensures that your ve-

hicle only has an interval service when it is

necessary. To calculate this (max. two years),

the conditions under which the vehicle is

used and the individual driving style are also

taken into account. The service pre-warning

will appear at 20 days or less prior to the cor-

responding service. The distance travelled is

rounded off to the nearest 100 km and the

time to full days. The current service message

can only be consulted 500 km or more after

the last service. Until that time, only dashes

are displayed.

by pressing the reset button ››› Fig. 70

Service

If a service is due, an audible warning will

sound and the flashing “spanner”  symbol

will be shown along with the fixed text SERV-

ICE.

Service interval display

If no service is carried out following the indi-

cation on the instrument panel, the excess

distance travelled and the excess time follow-

ing the SERVICE warning will be displayed.

Reading the service message

The current service message can be consul-

ted with the ignition on, the engine switched

off and the vehicle at a standstill:

Fig. 76 Service interval display

●



Press the

button on the instrument pan-

The service indication is shown on the instru-

Service warning

el as often as necessary until the “spanner”

ment panel display ››› Fig. 76.

symbol  is displayed.

A service warning will appear when the igni-

tion is switched on if a service is due soon.

SEAT distinguishes between services with en-

gine oil change (e.g. Interval Service) and

services without engine oil change (e.g. In-

Operation

An overdue service is indicated by a minus

tion.

Resetting service interval display

If the service was not performed by a SEAT

dealership, the display must be reset as fol-

lows:

●

Switch the ignition off.

0.0 / SET

Press and hold the

button.

Switch ignition back on.

0.0 / SET

Release the

button and press the



button within 20 seconds.

Do not reset the display between service in-

tervals, as the display will otherwise be incor-

rect.

If the display is reset manually, the next serv-

ice interval will be indicated after 15,000 km

or one year and will not be calculated individ-

ually.

Note

In LongLife Service vehicles, if the battery is

disconnected for a long period, the days re-

maining until the next service cannot be cal-

culated. Therefore, the service message indi-

cations may be incorrect. In this case, bear in

mind the maximum service intervals permit-

ted in the››› Booklet Maintenance Pro-

gramme.

Dash panel -> Digital instrument panel display for Your Seat Ibiza SUV Fourth Generation (2009-2017)

Related Topics

Popular Owner Manuals

Latest Owner Manuals