Get If and when -> Lamp change Guide for Seat Ibiza SUV Fifth Generation (2018-2026)

204

If and when

Number

Electrical equipment

Multi-terminal voltage supply “30”. Internal fuse box

Amperes

100

F1

G1

H1

Trailer fuse voltage supply in internal fuse box

Vacant

50

Some of the electrical items listed in the table are only fitted on certain

models or are optional extras.

Rear lights on tailgate

small position light 12V/W5W

foglight 12V/P21W

Please note that the above list, while correct at the time of printing, is subject

to alterations.

reverse light 12V/P21W

Single reflector headlamps

Full / dipped beam 12V 60/55W (H4)

indicator 12V/PY21W

Lamp change

position 12/W5W

Double reflector headlamps

dipped beam 12V/55W (H7)

full lights 12V/55W (H3)

indicator 12V/PY21W

General notes

Before changing any lamp first turn off the equipment concerned.

Do not touch the lamp glass. Fingerprints vaporise in the heat, causing a

reduction in the lamp life and condensation on the mirror surface, thus

reducing efficiency.

position 12V/W5W

7)

Xenon headlights

8)

A lamp should only be placed by one of the same type. The designation is

inscribed on the bulb, either on the glass part or on the base.

Dipped beam 12V/35W (D1S)

full beam 12V/55W (H7)

indicator 12V/PY21W

It is highly recommended to keep a box of spare lamps in the vehicle. At the

very least, the lamps that most affect road safety should have spares in the

vehicle.

position lights 12V/W5W

7)

For these type of headlights, the bulbs must be changed by an Authorised Service

Centre, given that complex elements of the vehicle must be removed and that the au-

tomatic control system must be reset.

Rear lights on frame

Brake/position 12V/P21/5W

Indicator 12V/P21W

8)

Xenon discharge lamps emit 2.5 times as much light flux and have a useful life five

times greater than halogen lamps, this means that, except in case of an abnormal

fault, there is no need to change the bulbs during the vehicle life.

If and when

205

Fog lights*

Main headlight lamps

Fog light 12V/55W (H3)

Registration plate light

Registration plate light - C5W

Caution

•

The halogen lamps (H3, H7, H4...) are pressurised and might explode on

changing them.

Therefore protective gloves and glasses should be worn when changing a

•

halogen lamp.

Note

Fig. 140 Main headlight

lamps

•

Due to the difficulty in accessing the lamps, these must be changed by an

Authorised Service Centre. However, we shall explain how to change these

lamps, except for the xenon lights*.

Fig. 141 Main headlight

lamps

A

A ^{Dipped headlights}

B

A ^{Main beam headlights}

Safety First

Operating instructions

Tips and Maintenance

Technical Data

206

If and when

C

A ^{Side lights}

D

A ^{Indicator lights}

Dipped headlight lamp

Fig. 143 Dipped head-

light lamp

–

Raise the bonnet.

2

^{Remove the loops}A⇒ fig. 142 outwards in the direction of the

arrow and remove the cover.

Fig. 142 Dipped head-

light lamp

A

–

^{Remove the lamp cable connector}A ⇒ fig. 143.

Undo the retainer spring and remove.

Remove the lamp and fit the new lamp in the same position,

making sure it sits correctly.

–

Press the retaining spring on the lamp base and clip on.

Plug in the connector.

2

^{Fit the plastic cover and replace the loops}A ⇒ fig. 142.

Check the headlight adjustment

If and when

207

2

–

^{Remove the loops}A⇒ fig. 144 outwards in the direction of the

arrow and remove the cover.

Main beam lights

B

–

^{Remove the lamp cable connector}A ⇒ fig. 145.

Undo the retainer spring and remove.

Remove the lamp and fit the new lamp in the same position,

making sure it sits correctly.

–

Press the retaining spring on the lamp base and clip on.

Plug in the connection cable.

2

^{Fit the plastic cover and replace the loops}A ⇒ fig. 144.

Fig. 144 Main beam lamp

Check the headlight adjustment

Fig. 145 Main beam lamp

–

Raise the bonnet.

Safety First

Operating instructions

Tips and Maintenance

Technical Data

208

If and when

1

–

^{Remove the loops}A⇒ fig. 146 in the direction of the arrow and

remove the cover.

Side beam lights

C

^{Pull on the cables to release the lamp holder from the casing}A

⇒ fig. 147.

–

Pull on the lamp and replace.

To assemble proceed in reverse order.

Fit the plastic cover and secure the loop.

Fig. 146 Side lights

Fig. 147 Side lights

–

Raise the bonnet.

If and when

209

1

–

^{Remove the loops}A⇒ fig. 148 in the direction of the arrow and

remove the cover.

Turn indicator lamps

Turn the lamp holder to the left and remove from casing

D

⇒ ^{fig. 149}A^.

–

Installation is done in the reverse order.

Fit the plastic cover and secure the loop.

Fig. 148 Indicator lights

Fig. 149 Indicator lights

–

Raise the bonnet.

Safety First

Operating instructions

Tips and Maintenance

Technical Data

210

If and when

Fog lights

F

–

^{Undo the two fastening screws}A⇒ fig. 150 and when released

unplug the connector.

–

Turn the headlamp cover to the left a quarter turn.

Unplug the lamp cable.

Undo the lamp retainer spring and remove.

Remove the lamp and fit the new lamp in the same position,

making sure it sits correctly.

–

Press the retaining spring on the lamp base and clip on.

Plug in the lamp cable.

Fig. 150 Fog lights

The assembly of the cover and the headlamp is carried out in

reverse order.

Fig. 151 Fog lights

A

–

^{Remove the grille, taking out the screw}A ⇒ fig. 150, carefully

pull the grille on the side of the screw and release the cover.

If and when

211

Side indicator lamps

Rear lights on the tailgate: Access to the light unit

Fig. 153 Rear light on

tailgate

Fig. 152 Side indicators

–

Press the indicator to the left or to the right to remove the lamp.

Remove the lamp holder from the indicator.

Remove the broken glass bulb and replace with a new bulb.

Insert the lamp holder in the indicator guide until it clicks into

place.

–

First fit the indicator in the opening in the chassis, fastening the

1

^tabsA ⇒ fig. 152, and then fit in the lamp as shown by the

2

^arrowA ⇒ fig. 152

Fig. 154 Rear light on

tailgate

Side light 1/ Fog light/ reverse light

Open the tailgate.

–

Safety First

Operating instructions

Tips and Maintenance

Technical Data

212

If and when

A

–

^{Remove the plastic cover}A ⇒ page 211, fig. 153 and the

B

^{plastic caps}A ⇒ page 211, fig. 153 carefully levering using a

screwdriver using the flat part of a screwdriver; avoid damage to

the paintwork.

C

–

^{Extract the bolts}A ⇒ page 211, fig. 154 and unplug the

connector.

Remove the light from its housing.

Fig. 156 Access to the

lamp

Rear lights on the tailgate: Access to the bulb

Side light 1/ Fog light/ reverse light

D

–

^{Unscrew the bolts}A ⇒ fig. 156 and remove the lampholder.

Press and rotate the large lampholder to the left. In the case of a

small lamp, rotate and extract the lampholder and pull on the

lamp.

–

Remove lamp and replace.

Fit the lampholder and proceed with installation.

Fig. 155 Rear light on

tailgate

B

A

^{Fit the caps}A ^{and the plastic cover}A ⇒ fig. 155.

Note

B

^{Ensure that all joints and rubber elements as well as the plastic caps}A ^are

correctly fitted during installation.

If and when

213

F

–

^{Unscrew the bolts}A ⇒ fig. 157 with the flat part of the screw-

driver.

Rear lights on frame

–

Move the light unit outwards and pull.

If necessary, unplug the connector.

G

^{Unscrew the bolt}A ⇒ fig. 158.

Take out the lampholder.

Press and rotate the lamps to the left.

Extract the faulty lamp and replace it.

Proceed in the reverse order for fitting, pressing gently on the

outer edge of the light unit (area of the metal clips).

Fig. 157 Rear lights on

the bodywork

Note

Make sure that when assembling all seals and rubbers are correctly fitted.

Number plate light

–

Release transparent lamp cover by levering the tab with the flat

part of a screwdriver.

Remove the defective lamp from the lamp holder, holding it in

the centre, press to one side and fit new lamp

Fig. 158 Rear lights on

the bodywork

Fit lamp cover in its space, taking special care when replacing the

rubber seal and press until it clicks into place.

Side light 2/ Brake light/ Indicator light

–

Open the tailgate.

Safety First

Operating instructions

Tips and Maintenance

Technical Data

214

If and when

–

First fit the glass with the fastening tabs over the frame of the

switch. Next press the front part until the two long tabs click on

the support.

Interior light and front reading light

Additional brake lights*

Given the difficulty involved in the replacement of this light it should be done

by the Technical Service.

Glovebox light*

Fig. 159 Front reading

light

–

Insert screwdriver above, between the light and the glove box.

Carefully remove the light Next lift the light out sideways.

Replace the bulb .

To remove glass

–

Insert a fine screwdriver between the casing and the

glass ⇒ fig. 159.

Insert the light on the connector side, first underneath then push

at the top until it clicks into place.

–

Carefully remove the glass, levering it to avoid possible damage.

To replace the lamps

–

Pull the lamps outwards.

Jump-starting

To remove the central lamp, hold and press to one side.

Jump leads

Assembly

Proceed in the reverse order, pressing gently on the outer edge

of the side light.

–

The jump lead must have a sufficient wire cross section.

If the engine fails to start because of a discharged battery, the battery can be

connected to the battery of another vehicle to start the engine.

If and when -> Lamp change for Your Seat Ibiza SUV Fifth Generation (2018-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals