Get Lighting,windscreenwipersandwashers -> Replace light bulbs Guide for Skoda Fabia 4 Door Fourth Generation (2021-2026)

Lighting, windscreen wipers and washers › COMING HOME, LEAVING HOME exterior lighting 39

Beam of light in front of the vehicle has shortened

Headlight defective.

Operation

Switching on

Seek the help of a specialist garage.

›

Push the lever in the

direction of the arrow.

›

Driving lights defective

If a message regarding the failed driving lights is dis-

played, the light will work in emergency mode.

It lights up in the instru-

ment cluster

from

Drive on, exercising appropriate caution.

Seek the help of a specialist garage.

›

the isolation box.

Switching oﬀ

COMING HOME, LEAVING HOME

exterior lighting

Manually switch the high beam on or oﬀ.

›

Functionality

Function restriction

The COMING HOME function turns on the light after

turning oﬀ the ignition and opening the driver's door.

The light switches oﬀ automatically after the set

lighting time has elapsed.

The system may dazzle other road users if their

headlights/lights are not detected for the following

reasons, for example:

The headlights/lights of oncoming vehicles are

covered by crash barriers, for example.

▶

The LEAVING HOME function switches on the light

when unlocking the vehicle with the wireless remote

control.

The headlamps/lights of the oncoming or preced-

ing vehicle are dirty or not functioning.

▶

Operating conditions

Settings

✓ Visibility has worsened.

Activation/deactivation

The function is activated or deactivated as follows in

✓

The light switch is in the

position.

the Infotainment system in the menu

Settings

Replace light bulbs

This function is set in the following menu in the Info-

tainment system:

What you should be mindful of

DIY replacement of the following bulbs is possible.

Have the remaining light sources replaced by a spe-

cialist garage.

Light Assist high-beam assist system

Functionality

The new bulb must conform to the speciﬁcation of

the original light bulb. The name of the bulb is

marked on the bulb socket.

The high beam assist system automatically switches

the high beam on and oﬀ.

After changing a bulb in the low beam light, the main

beam or fog light, have the headlights adjusted by a

specialist garage.

WARNING

Risk of accident!

If necessary, manually switch the high beam on or

CAUTION

▶

oﬀ.

Halogen lamps are pressurised and can burst during

replacement!

Wear gloves and safety goggles.

▶

Operating conditions

NOTICE

Contamination of the halogen lamp reduces the life

of the lamp!

✓ The system is activated.

✓

The light switch is in the

position.

Do not touch the glass of the light bulb with your

▶

✓ The driving speed is higher than 60 km/h (for

bare ﬁngers.

some countries, higher than 40 km/h).

✓ The low beam is switched on.

40 Lighting, windscreen wipers and washers › Replace light bulbs

Replacing the light bulb

NOTICE

Danger of headlight damage due to the ingress of

water and dirt!

Protective caps on the

headlight:

Always ﬁt the protective cap on the headlight cor-

▶

Low beam

Main beam

rectly after changing a bulb.

Conditions for changing a bulb

Remove the associated

protective cap.

›

✓ Ignition oﬀ

✓ Light switched oﬀ

Press the socket with

the light bulb down-

wards and remove it.

›

Low beam and high beam

Before changing the light bulb for the high beam in

the right headlight

Disconnect the washer

ﬂuid reservoir from the

›

bracket.

Change the bulb in the

socket.

›

Insert the socket with

the new light bulb into

the headlight, so that

the ﬁxing lug A is

pointing up.

Insert the socket until

it clicks into place.

Fit the protective cap

›

on the headlight again.

After changing the light bulb for the low beam

light

Insert the cover in the wheel arch and lock into

place.

›

› ^{Insert one ﬁnger into the recess}A and lift the

latch B on the bracket.

After changing the light bulb for the high beam in

the right headlight

Remove the bracket.

›

Reinstall the washer ﬂuid reservoir holder.

›

Before changing the light bulb for the low beam

light

Insert the container nozzle back into the holder.

›

Adjust the front wheels so that the cover cap in

the wheel arch is accessible.

›

Front turn signal

Insert the bracket from

the tool kit into the re-

cess in the cover cap.

Remove the cover by

pulling on the bracket.

›

Before changing the bulb in the right headlight

Disconnect the washer

ﬂuid reservoir from the

bracket.

›

Lighting, windscreen wipers and washers › Replace light bulbs 41

Fog lights

Release the cover with

the bracket from the

tool kit and remove it.

›

› ^{Insert one ﬁnger in the recess}A and lift B the

bracket latch.

Remove the bracket.

› ^Unscrewscrews A.

›

Take out the lamp.

Replacing the light bulb

Release the connector

and remove it from the

bulb.

›

Protective cap: Halogen headlights/LED headlights

Remove the protective cap from the headlight.

›

Turn and remove the

›

socket with the bulb.

Turn the light bulb and

take it out.

›

Push the new light bulb

›

into the light so that

the guide lugs on the

light bulb and the asso-

ciated openings in the

light are in alignment.

Change the bulb in the

socket.

›

Insert the socket with

›

Turn the bulb clock-

wise to secure.

Attach the connector to the bulb, ensuring it clicks

into place.

Reinstall the lamp and screw it on.

›

the light bulb into the

headlight and turn it

clockwise to secure.

Reinstall the protective

cap on the headlight.

After changing the

bulb in the right head-

light, reuse the bracket

›

Replace the cover and push it in until it clicks into

place.

›

for the wash water container nozzle .

42 Lighting, windscreen wipers and washers › Replace light bulbs

Change bulb - Variant 2 (light only with light bulbs)

Taillight

Change the bulb in the

outer part of the lamp.

Loosen and remove the lamp

› ^Unscrewthe screws A .

Turn and remove the

›

Insert the bracket from

the tool kit into the re-

cess in the light.

›

socket with the bulb.

On the left-hand lamp,

the eyelet of the

bracket must point

downwards, and up-

wards on the right

lamp.

Change the bulb in the

socket.

›

Remove the lamp with the bracket.

Push the base with the

›

new light bulb into the

luminaire so that the

guide lugs on the base

and the associated

openings in the lumin-

aire are ﬂush.

› ^Pullthe lock A some-

what out of the plug.

Press the safety button

and pull out the plug.

›

Turn the socket clock-

wise to secure.

›

Change the bulb in the

inner part of the lamp.

Change bulb - Variant 1 (light with LED light sour-

ces)

Unlock and remove the

lamp holder A .

›

Unlock and remove the

lamp holder the lock A .

›

Turn the defective light

bulb and take it out of

the holder.

›

Insert a new light bulb

›

into the socket and se-

cure the light bulb by

turning it in the direc-

Turn the defective light

bulb and take it out of

the holder.

›

tion of

Insert a new light bulb

›

Insert the bulb holder

into the light and snap

into place.

›

into the socket and se-

cure the light bulb by

turning it in the direc-

tion of

Insert and ﬁx the lamp

Insert the connector into the light until it clicks into

place.

›

Check that the con-

nector the lock A is se-

›

Press in the slightly pulled out latch on the connec-

tor.

›

curely connected.

Insert the bulb holder into the light and snap into

place.

›

NOTICE

Risk of damage to the electrical system!

Make sure that no cables are trapped when insert-

ing the holder into the lamp.

▶

Lighting,windscreenwipersandwashers -> Replace light bulbs for Your Skoda Fabia 4 Door Fourth Generation (2021-2026)

Related Topics

Lighting,windscreenwipersandwashers

Popular Owner Manuals

Latest Owner Manuals