2001-2008 Skoda Superb SUV Using the system -> Instruments and Indicator/Warning Lights User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Using the system -> Instruments and Indicator/Warning Lights for Your Skoda Superb SUV First Generation (2001-2008)

Instruments and Indicator/Warning Lights 11  
Instruments and Indicator/Warning Lights  
General view of the instrument cluster  
Fig. 2 Instrument cluster  
1
A Engine revolutions counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
12  
12  
When the lights are switched on, the instrument cluster is illuminated.  
2
A Coolant temperature gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
3
A Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
12  
4
13, 15  
18  
A Digital clock and multi-functional indicator . . . . . . . . . . . . . . . . . . .  
5
A Information display* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
6
A Speedometer  
−
−
−
with counter for distance driven . . . . . . . . . . . . . . . . . . . . . . . . . .  
with trip counter for distance driven . . . . . . . . . . . . . . . . . . . . . . .  
with Service Interval Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
13  
13  
14  
Using the system  
Safety  
Driving Tips  
General Maintenance  
Breakdown assistance  
Technical Data  
12 Instruments and Indicator/Warning Lights  
The operating range  
Engine revolutions counter  
The engine has reached its operating temperature as soon as the pointer moves  
into the mid-range of the scale. The pointer may also move further to the right at  
high engine loads and high outside temperatures. This is not critical provided the  
warning symbol in the instrument cluster does not flash.  
1
The start of the red zone in the revolutions counter A ⇒ page 11, fig. 2 indicates  
the maximum permissible engine speed for all gears for an engine which has been  
run in and operating at a normal temperature. You should shift into the next higher  
gear before this red zone is reached, or move the selector lever into position D if  
your car is fitted with an automatic gearbox.  
If the symbol in the instrument cluster flashes it means that either the coolant  
temperature is too high or the coolant level is too low. Please refer to the guide-  
lines ⇒ page 26, “Coolant temperature, Coolant quantity ”.  
One should shift to the next lower gear at the latest when the engine is no longer  
running “smoothly”.  
Avoid high engine speeds during the running-in period ⇒ page 162.  
WARNING  
Pay attention to the warning notes ⇒ page 185, “Working in the engine  
compartment” before opening the bonnet and inspecting the coolant level.  
Caution  
The needle of the revolutions counter must on no account move into the red zone  
of the scale - risk of engine damage!  
Caution  
Additional headlights and other attached components in front of the fresh air inlet  
impair the cooling efficiency of the coolant. There is then a risk of the engine over-  
heating at high outside temperatures and high engine loads!  
For the sake of the environment  
Shifting up early helps you save fuel and reduce the operating noise of your  
vehicle.  
Fuel gauge  
Coolant temperature gauge  
3
The fuel gauge A⇒ page 11, fig. 2 only operates when the ignition is switched on.  
2
The coolant temperature gauge A ⇒ page 11, fig. 2 operates only when the igni-  
tion is switched on.  
The fuel tank has a capacity of about 62 litres. The warning symbol in the instru-  
ment cluster lights up when the pointer reaches the reserve marking. There are now  
about 8 litres of fuel remaining in the tank. This symbol is a reminder for you, that  
you must refuel.  
In order to avoid any damage to the engine, please pay attention to the following  
notes regarding the temperature ranges:  
The following will be displayed in the information display*:  
PLEASE REFUEL  
Cold range  
If the pointer is in the left-hand area of the scale it means that the engine has not  
yet reached its operating temperature. Avoid running at high engine speeds, at full  
throttle and at severe engine loads.  
A peep sounds as an additional warning signal.  
Instruments and Indicator/Warning Lights 13  
Speedometer with counter for distance driven  
Caution  
Never run the fuel tank completely empty! An irregular fuel supply can result in  
poor ignition or misfiring. Unburnt fuel may get into the exhaust system and  
damage the catalytic converter.  
Digital clock  
Fig. 4 Instrument  
cluster: Counter for  
distance driven  
The distance which you have driven with your vehicle is shown in kilometres (km).  
On certain model versions, the readout is shown in “miles”.  
Bottom counter (trip counter) for distance driven  
Fig. 3 Instrument  
cluster: Digital clock  
The bottom counter indicates the distance which you have driven since this  
counter was last reset - in steps of 100 metres or 1/10 of a mile. It can be reset to  
zero by pressing the reset button next to the trip counter ⇒ fig. 4.  
You can set the time with the reset button at the bottom right next to the  
rev counter.  
Top counter for distance driven  
The top counter for distance driven indicates the total distance in kilometres or  
miles which the vehicle has been driven.  
Set hours  
–
Turn the reset button to the left.  
Fault display  
dEF will appear as a constant text in the display field of the counter for distance  
driven if there is a fault in the instrument cluster. Have the fault rectified as soon as  
possible by a specialist workshop.  
Setting minutes  
–
Turn the reset button to the right.  
Warning against excessive speeds*  
An acoustic warning signal will sound when the vehicle speed exceeds 120 kilome-  
tres per hour. The acoustic warning signal will switch off again when the vehicle  
speed goes below this speed limit.  
WARNING  
The clock should not be adjusted while driving for safety reasons but only  
when the vehicle is stationary!  
This function is only valid for some countries.  
Using the system  
Safety  
Driving Tips  
General Maintenance  
Breakdown assistance  
Technical Data  
14 Instruments and Indicator/Warning Lights  
WARNING  
in information display  
SERVICE NOW  
Never seek to adjust the trip counter for distance driven while driving for  
safety reasons!  
The display disappears within 20 seconds after starting the engine. The trip counter  
is also displayed after pressing the reset button of the trip counter (for more than 1  
second).  
Service Interval Display  
Resetting Service Interval Display  
We recommend having this resetting performed by a specialist garage.  
The specialist garage:  
•
•
•
resets the memory of the display after the appropriate inspection,  
makes an entry in the Service schedule,  
affix the sticker with the entry of the following service interval to the side of the  
dash panel on the driver's side.  
It is also possible for you to reset the Service Interval Display with the reset button  
B
A⇒ fig. 5 as follows (does not apply to models with fixed service intervals - QG2).  
Fig. 5 Instrument  
cluster: Service Interval  
Display  
B
•
Switch off the ignition (if not already off), press the reset button A and hold it  
down.  
Switch the ignition on and release the reset button A. The text Service or  
service now appears in the display.  
Turn the button for resetting the clock A to the right - the display is reset.  
B
•
Depending on the equipment installed in the vehicle, the information appears in  
the display of the counter for distance driven or in the information display ⇒ fig. 5.  
A
•
Service Interval Display  
If the due date for the service is reached, the following text appears after switching  
on the ignition:  
Caution  
We recommend that you do not reset the Service Interval Display yourself other-  
wise this can result in the service interval display being incorrectly set, which may  
also result in problems with operation of your vehicle.  
in the display of the trip counter  
Service 1 500 km  
in information display  
SERVICE in 1500 km  
Note  
•
Never reset the display between service intervals otherwise this may result in  
incorrect readouts.  
information is retained in the Service Interval Display also after the battery of  
the vehicle is disconnected.  
Prior to the due date for the service the kilometre readout decreases in steps of 100  
km. As soon as the due date for the service is reached, the following text appears:  
•
in the display of the trip counter  
Service  
Instruments and Indicator/Warning Lights 15  
•
it is necessary to re-code the Service Interval Display if a new instrument cluster  
is installed during repair work. This work is carried out by a specialist garage.  
Average fuel consumption  
Driving time  
⇒ page 17  
⇒ page 17  
⇒ page 18  
⇒ page 18  
•
After resetting the display with flexible service intervals (QG1) using the reset  
B
button A, the data displayed are the same as for a car with fixed service intervals  
(QG2). We therefore recommend having the Service Interval Display reset only by a  
Škoda Service Partner who is familiar with the procedure for resetting the display  
with a vehicle system tester.  
Distance driven  
Average speed  
•
Please refer to the brochure Service schedule for extensive information about  
the service intervals.  
Note  
In certain national versions the displays appear in the Imperial system of  
measures.  
Multi-functional indicator (onboard computer)  
Memory  
Introduction  
Fig. 7 Multi-functional  
indicator: Memory level  
Fig. 6 Multi-functional  
indicator: Average fuel  
consumption  
The multi-functional indicator is equipped with two automatic memories. You can  
see the memory which is currently being shown in the display from the negatively  
displayed number ⇒ fig. 7.  
The multi-functional indicator appears in the display of the revolutions counter  
⇒ page 11, fig. 2 or in the information display ⇒ fig. 6 depending on the equip-  
ment fitted to your vehicle.  
The data of the single-trip memory (memory 1) is shown if a 1 appears in the  
display. A 2 shown in the display means that data relates to the total distance  
memory (memory 2).  
The multi-functional indicator offers you a range of useful information.  
The outside temperature  
Range  
⇒ page 16  
⇒ page 17  
⇒ page 17  
B
Switching of the memory takes place when the button A ⇒ page 16, fig. 8.  
Current fuel consumption  
Using the system  
Safety  
Driving Tips  
General Maintenance  
Breakdown assistance  
Technical Data  
16 Instruments and Indicator/Warning Lights  
Single-trip memory (memory 1)  
Selecting the memory  
Repeated short-term pressing of the button A allows one to select  
the individual memories.  
The single-trip memory collates the driving information from the moment the igni-  
tion is switched on until it is switched off. New data will also flow into the calcula-  
tion of the current driving information if the trip is continued within 2 hours after  
switching off the ignition. The memory will be is automatically erased, on the other  
hand, if the trip is interrupted for more than 2 hours.  
B
–
Selecting the functions  
Press the rocker switch A up or down. This will cause the individual  
A
–
Total-trip memory (memory 2)  
functions of the multi-functional indicator to appear in the display  
one after the other.  
The total distance driven memory gathers data from any number of individual jour-  
neys up to a total of 99 hours and 59 minutes driving or 9.999 kilometres driven.  
The memory is deleted when either of these limits is reached and the calculation  
starts from anew.  
Setting function to zero  
–
–
Select the memory you want.  
The total-trip memory will not, contrary to the single-trip memory, be deleted after  
a period of interruption of driving of 2 hours.  
B
Press button A for more than 1 second.  
B
The following readouts of the selected memory will be set to zero by button A:  
Note  
•
•
•
•
average fuel consumption,  
distance driven,  
All information in the memory is erased if the battery of the vehicle is  
disconnected.  
average speed,  
Driving time.  
Using the system  
You can only operate the multi-functional indicator when the ignition is switched  
on. After the ignition is switched on, the function displayed is the one which you last  
selected before switching off the ignition.  
The outside temperature indicator will appear with a snowflake symbol and a  
warning signal sounds* when the outside temperature lies between +5°C and -5°C.  
The symbol warns the driver of the possible danger of ice on the road. After the  
A
rocker switch A is pressed, the function displays the one which you last selected  
before switching off the ignition.  
Fig. 8 Multi-functional  
indicator: Control  
elements  
Outside temperature  
The outside temperature appears in the display when the ignition is switched on.  
The correct outside temperature will be indicated with a delay of 5 minutes. If the  
vehicle is stationary (or driven at a very low speed) the temperature indicated may  
A
B
The rocker switch A and the button A are located in the grip of the  
window wiper lever ⇒ fig. 8.  
Instruments and Indicator/Warning Lights 17  
Fuel - present consumption  
be slightly higher than the actual outside temperature because of heat radiated by  
the engine.  
The current fuel consumption level is shown in the display in litres/100 km. This  
information can help you to adapt your style of driving to the fuel consumption you  
wish to achieve.  
The outside temperature indicator will appear with a snowflake symbol (warning  
signal for ice on the road) and a warning signal sounds* when the outside temper-  
ature lies between +5°C and -5°C.  
The display appears in litres/hour if the vehicle is stationary or driving at a low  
speed.  
WARNING  
Do not only rely upon the information given on the outside temperature  
display that there is no ice on the road. Please note that black ice may also be  
present on the road surface even at temperatures around +5°C - warning,  
drive with care!  
Average fuel consumption  
The average fuel consumption since the memory was last erased is shown in the  
display in litres/100 km ⇒ page 15. This information can help you to adapt your  
style of driving to the fuel consumption you wish to achieve.  
Note  
If you wish to determine the average fuel consumption over a certain period of time  
you must first erase the memory at the start of the new measurement using the  
The outside temperature is not indicating when showing navigation data (guidance  
to the destination). It must be called up over the menu (valid for vehicles which  
have a navigation and information display).  
B
button A ⇒ page 16, fig. 8. A zero appears in the display for the first 300 m you  
drive after erasing the memory.  
The indicated value will be updated every 30 metres while you are driving.  
Range  
Note  
The estimated range in kilometres is shown on the display. It indicates the distance  
you can still drive with your vehicle based on the present level of fuel in the tank for  
the same style of driving. The readout is shown in steps of 5 km.  
The amount of fuel consumed will not be indicated.  
The fuel consumption for the last 50 km is taken as a basis for calculating the range.  
If you drive in a more economical manner from this moment on, the range will be  
increased accordingly.  
Driving time  
The driving time which has elapsed since the memory was last erased, appears in  
the display ⇒ page 15. If you wish to calculate the driving time from a particular  
time of day you must first erase the memory at this moment in time by pressing the  
You first drive 50 km if the readout is reset (after disconnecting the battery) before  
a new readout for the range is displayed.  
B
button A ⇒ page 16, fig. 8.  
The maximum time indicated in both switch positions is 99 hours and 59 minutes.  
The indicator is set back to null if this period is exceeded.  
Using the system  
Safety  
Driving Tips  
General Maintenance  
Breakdown assistance  
Technical Data  
18 Instruments and Indicator/Warning Lights  
Distance driven  
The information display provides you with information in a convenient way  
concerning the current operating state of your vehicle. The information system  
also provides you with data (depending on the equipment installed in the vehicle)  
relating to the radio, multi-functional indicator, navigation system and automatic  
gearbox.  
The distance driven since the memory was last erased appears in the display  
⇒ page 15. If you wish to calculate the distance driven from a particular time of day  
you must first erase the memory at this moment in time by pressing the button A  
B
⇒ page 16, fig. 8.  
Certain functions and operating conditions are always being checked on the  
vehicle when the ignition is switched on and also while driving.  
The maximum distance indicated in both switch positions is 9 999 km. The indicator  
is set back to null if this period is exceeded.  
Functional faults, if required repair work and other information are indicated by red  
symbols ⇒ page 21 and yellow symbols ⇒ page 21.  
Lighting up of these symbols is combined with an acoustic warning signal.  
Information and texts giving warnings are also shown in the display ⇒ page 22.  
The display of text is possible in the following languages:  
Average speed  
The average speed since the memory was last erased is shown in the display in  
km/h ⇒ page 15. If you wish to determine the average speed over a certain period  
of time you must first erase the memory at the start of the new measurement using  
Czech, English, German, French, Italian, Spanish, Portuguese.  
You can have the relevant language set by a specialist garage.  
B
the buttonA ⇒ page 16, fig. 8.  
A zero appears in the display for the first 100 m you drive after erasing the  
memory.  
The following information can be shown in the display (depending on the equip-  
ment installed on the vehicle):  
Menu  
⇒ page 19  
⇒ page 19  
Information display*  
Door, luggage compartment door and bonnet ajar  
warning  
Introduction  
Radio display  
⇒ page 20  
⇒ page 116  
⇒ page 14  
⇒ page 110  
Information from the telephone  
Service Interval Display  
Selector lever position for an automatic gearbox  
On models fitted with an automatic gearbox, the information in the display appears  
only after a drive position is engaged.  
Fig. 9 Instrument  
cluster: Information  
display  
Instruments and Indicator/Warning Lights 19  
Menu  
TRIP COMPUTER (AUTO COMPUTER)  
⇒ page 15  
⇒ page 20  
CAR STATUS  
DISPLAY OFF  
NAVIGATION  
⇒ page 22  
After selecting the menu DISPLAY OFF the display is switched off. Press rocker  
A
switch A for at least 1 second to switch the display on again.  
The Information CAR STATUSflashes in the menu if there is something which is not  
in proper order on the vehicle (e.g. warning of a low fuel level). The first warning will  
be displayed after switching over to CAR STATUS. You can then display other oper-  
ating conditions afterwards using the switch-over function (such as water level  
low).  
Fig. 10 Information  
display: Menu  
Door, luggage compartment door and bonnet ajar warning  
Fig. 11 Information  
display: Control  
elements  
A
–
–
You can activate the menu by pressing the rocker switch A ⇒ fig. 11  
Fig. 12 Information  
display: Door warning  
for more than 1 second.  
A
You can select the menu through the rocker switch A. The selected  
B
information is displayed after pressing the button A for a short time  
The door, luggage compartment door and bonnet ajar warning lights up when at  
least one of the three items door, luggage compartment or bonnet are not closed  
when the ignition is turned on. The symbol indicates which door is still open or  
whether the luggage compartment door or bonnet is not closed ⇒ fig. 12.  
A
or after releasing the rocker switch A (after about 4 seconds).  
You can select the following information (depending on the equipment installed on  
the vehicle):  
The symbol goes out as soon as the doors, luggage compartment door and bonnet  
are completely closed.  
Using the system  
Safety  
Driving Tips  
General Maintenance  
Breakdown assistance  
Technical Data  
20 Instruments and Indicator/Warning Lights  
As an additional warning signal, a 3 time peep sounds if the car is driven at a speed  
of more than 6km/hour and if the door is open.  
Investigate the displayed faults as soon as possible. If several operational faults exist  
at the same time, the symbols will appear one after the other and are each visible  
for about 2 seconds.  
The error messages are faded out after 10 seconds or by actuating the rocker switch  
Radio display  
A
A ⇒ page 19, fig. 11 and are stored under the information CAR STATUS.  
There is at least one error message to be read when the term CAR STATUS is  
flashing in the main menu. The display will show STATUS 1/2 (for example) if a  
number of error messages are present. This display indicates that the first of a total  
of two error messages should be displayed.  
A
Actuate the rocker switch A, to call up the individual error messages.  
If a fault occurs, a warning signal will also sound in addition to the symbol and text  
in the display:  
•
•
Priority 1 - three warning signals  
Priority 2 - one warning signal  
Fig. 13 Information  
display: Radio display  
Operational check of the automatic gearbox  
These displays appear in addition to the normal information in the radio display.  
When the ignition is switched on, the Auto Check Control automatically carries out  
an operational check. The following text will appear first if the selector lever is the  
position P or N:  
Auto Check Control  
Car state  
"APPLY FOOT BRAKE WHEN SELECTING GEAR WITH VEHICLE  
STATIONARY." (Apply foot brake when selecting a gear while the vehicle is  
stationary).  
The Auto Check Control carries out a check of certain functions and vehicle compo-  
nents. The check is performed constantly when the ignition is switched on, both  
when the vehicle is stationary, as well as when driving.  
You must depress the brake pedal first and press the Shiftlock button at the same  
time in order to move the selector lever out of these positions.  
Operational faults, urgent repairs, service work or other information appear in the  
display of the instrument cluster. The displays are shown with a red or yellow light  
symbol depending on the priority of the message.  
The text will disappear once you select a drive position (R, D etc.), and the Auto  
Check Control function is displayed.  
If the Auto Check Control detects faults, these will be displayed about 15 seconds  
after starting the engine in place of the text shown above. A warning signal sounds  
at the same time.  
The red symbols indicate danger (priority 1) while the yellow symbols indicate a  
warning (priortity 2). Information for the driver may also appear in addition to the  
symbols ⇒ page 22.  
Instruments and Indicator/Warning Lights 21  
If several operational faults of priority 1 exist, the symbols appear one after the  
other and are each illuminated for about 2 seconds.  
Red symbols  
A red symbol signals danger.  
Yellow symbols  
A yellow symbol signals a warning.  
Fig. 14 Information  
display: Oil pressure is  
low  
Proceed as follows if a red symbol is displayed:  
Fig. 15 Information  
display: Fuel level low  
–
–
–
–
Stop the vehicle.  
Switch the engine off.  
The meaning of the yellow symbols:  
Investigate the function indicated.  
Obtain professional assistance.  
Fuel level low  
⇒ page 27  
⇒ page 27  
⇒ page 26  
⇒ page 28  
⇒ page 28  
⇒ page 28  
Check engine oil level, engine oil sensor faulty  
Brake pad worn  
Meaning of the red symbols:  
Faults in the brake surface  
⇒ page 29  
⇒ page 26  
⇒ page 27  
Washer fluid level low  
Coolant level too low/coolant temperature  
too high  
Light bulb defect  
Engine oil pressure too low  
Light bulb in the brake light defect  
Three successive warning signals will sound if a red symbol appears. The symbol  
continues flashing until the fault is rectified.  
One warning signal will sound if a yellow symbol appears.  
Using the system  
Safety  
Driving Tips  
General Maintenance  
Breakdown assistance  
Technical Data  
22 Instruments and Indicator/Warning Lights  
If several operational faults of priority 2 exist, the symbols appear one after the  
other and are each illuminated for about 2 seconds.  
Navigation system*  
The controls for the navigation system, radio, CD player are located in the centre  
console on both sides of the monitor screen. Navigation data is also shown in the  
information display of the instrument cluster.  
Check the relevant function as soon as possible.  
Information and warning texts are displayed preferentially when the navigation  
system is switched on.  
Operation of the navigation system is described in separate operating instructions  
to be found in the on-board literature.  
Warning lights  
Overview  
The warning lights indicate certain functions or faults.  
Fig. 16 Instrument cluster with warning lights  
Instruments and Indicator/Warning Lights 23  
Open door  
Turn signal lights (to the left)  
Turn signal lights (to the right)  
Main beam  
⇒ page 28  
⇒ page 24  
⇒ page 24  
⇒ page 24  
⇒ page 24  
⇒ page 24  
⇒ page 25  
⇒ page 25  
⇒ page 25  
⇒ page 25  
⇒ page 25  
⇒ page 26  
⇒ page 26  
⇒ page 26  
⇒ page 27  
⇒ page 27  
⇒ page 27  
Fluid level in windshield washer system  
Bulbs  
⇒ page 28  
⇒ page 28  
⇒ page 28  
⇒ page 28  
⇒ page 28  
⇒ page 29  
⇒ page 29  
⇒ page 29  
⇒ page 30  
⇒ page 30  
Control system for exhaust  
Electronic stability programme (ESP)*  
Traction control system (TCS)*  
Antilock brake system (ABS)  
Electronic immobiliser  
Brake system  
Airbag system  
Turn signal system for vehicles towing a trailer  
Low beam  
Fog lights  
Rear fog light  
  
EPC fault light (petrol engine)  
Diesel particle filter (diesel engine)  
Glow plug system (diesel engine)  
Coolant temperature/coolant level  
Brake pad wear  
Dynamo  
Seat belt warning light  
WARNING  
•
If you do not pay attention to the warning lights coming on and the corre-  
sponding descriptions and warning notes, this may result in severe body  
injuries or major vehicle damage.  
Bonnet  
•
The engine compartment of your car is a hazardous area. There is a risk  
Fuel reserve  
of injuries, scalding, accidents and fire when working in the engine  
compartment, e.g. inspecting and replenishing oil and other fluids. It is also  
essential to observe all warnings ⇒ page 185.  
Engine oil  
Using the system  
Safety  
Driving Tips  
General Maintenance  
Breakdown assistance  
Technical Data  
24 Instruments and Indicator/Warning Lights  
Note  
The following text will be displayed in the information display*:  
AIRBAG FAULT  
•
Arrangement of the indicator lights depends on the model and model version.  
The functionality of the airbag system is also monitored electronically, when one  
airbag has been switched off  
The symbols shown in the following functional description are to be found as indi-  
cator lights in the instrument cluster.  
Front, side or head front passenger airbags which have been switched off  
using the vehicle system tester:  
•
Operational faults are shown in the display of the instrument cluster as red  
symbols (priority 1 - danger) or yellow symbols (priority 2 - warning).  
•
The warning light lights up for 3 seconds after switching on the ignition and  
then flashes for 12 seconds afterwards in 2 second intervals.  
Turn signal system   
Front, side or head passenger airbags which have been switched off using the  
switch (for switching off airbags)* in the storage compartment on the front  
passenger side:  
Either the left or right indicator light flashes depending on the position of the  
turn signal lever.  
•
The warning light comes on for 3 seconds after the ignition has been  
switched on.  
The indicator light flashes at twice its normal rate if a turn signal light fails. This does  
not apply when towing a trailer.  
•
Switching off airbags is indicated in the middle of the dash panel by the lighting  
up of the indicator light   (airbag switched off) ⇒ page 144.  
Switching off the hazard warning light system is switched on will cause all of the  
turn signal lights as well as both indicator lights to flash.  
Further information about the turn signal system ⇒ page 49.  
WARNING  
Have the airbag system checked immediately by a specialist garage if a fault  
exists. Otherwise, there is a risk of the airbag not being activated in the event  
of an accident!  
Main beam   
The indicator light comes on when the main beam is selected or also when the  
headlight flasher is operated.  
Note  
Further information about the main beam ⇒ page 49.  
Further information about switching off airbags ⇒ page 144, “Deactivating an  
airbag”.  
Airbag system  
Turn signal system for vehicles towing a trailer  
Monitoring the airbag system  
The warning light comes on for a few seconds when the ignition is switched on.  
The indicator light on vehicles towing a trailer flashes together with the respec-  
tive indicator light for the turn signal system.  
There is a fault in the system if the warning light does not go out or comes on or  
flashes while driving ⇒  
. This also applies if the warning light does not come on  
The indicator light does not flash if a turn signal light on the trailer or on the  
vehicle is not operating.  
when the ignition is switched on.  
Instruments and Indicator/Warning Lights 25  
Always pay attention to the valid speed limits ⇒  
.
Low beam   
The warning light goes out after the successful cleaning of the diesel particle  
filter.  
The indicator light comes on when low beam is selected ⇒ page 46.  
If these conditions are not met, the warning light does not go out and the  
warning light begins to flash. ENGINE WORKSHOP! is shown in the informa-  
tion display*. Afterwards the engine control unit shifts the engine into the emer-  
gency mode, which only has a reduced power output. After switching the ignition  
off and on again the warning light comes on.  
Fog lights   
The warning light comes on when the fog lights are operating ⇒ page 47.  
Have the vehicle inspected without delay by your specialist garage.  
Rear fog light   
WARNING  
The warning light comes on when the rear fog lights are operating ⇒ page 47.  
•
If you do not pay attention to the warning light coming on and the corre-  
sponding descriptions and warning notes, this may result in injuries or  
major vehicle damage.  
EPC fault light  (petrol engine)  
•
Always adjust your speed to suit weather, road, region and traffic condi-  
tions. The route indicated by the warning light must not tempt you to disre-  
gard the national regulations for road traffic.  
The  (Electronic Power Control) warning light comes on for a few seconds when  
the ignition is switched on.  
There is a system fault in the engine control system if the warning light  does not  
go out or comes on or flashes while driving. The engine management system  
selects an emergency programme which enables you to drive to the nearest  
specialist garage by adopting a gentle style of driving.  
Caution  
As long as the warning light lights up, one must take into account an increased  
fuel consumption and in certain circumstances a power reduction of the engine.  
The following text will be displayed in the information display*:  
ENGINE WORKSHOP! (ENGINE FAULT - WORKSHOP!)  
Note  
•
The servicing of the diesel particle filter and the replenishing of the additive are  
performed by a specialist garage in the framework of the regular inspection, see  
Service shedule.  
Diesel particle filter* (diesel engine)  
If the warning light comes on, this means that soot has accumulated in the diesel  
particle filter because of the frequent short distances.  
•
Further information about diesel particle filter ⇒ page 160, “Diesel particle  
filter* (diesel engine)”.  
In order to clean the diesel particle filter, the vehicle should be driven at an even  
speed of at least 60 km/h at engine speeds of 1 800 - 2 500 rpm for 15 minutes or  
until the warning light goes out with the 4th or 5th gear engaged (automatic  
gearbox: position S) when the traffic situation permits it. This increases the exhaust  
temperature and the soot deposited in the diesel particle filter is burnt.  
Using the system  
Safety  
Driving Tips  
General Maintenance  
Breakdown assistance  
Technical Data  
26 Instruments and Indicator/Warning Lights  
obtain professional assistance from a specialist garage, otherwise it could lead to  
severe engine damage.  
Glow plug system (diesel engine)  
The indicator light lights up for a cold engine when switching on the ignition  
(pre-heat position) 2 ⇒ page 100. Start the engine just as soon as the indicator light  
goes out.  
If the coolant is within the specified range, the increased temperature may be  
caused by an operating problem at the coolant fan. Check the fuse for the coolant  
fan, replace it if necessary ⇒ page 220, “Replacing fuses”.  
The glow plug indicator light will come on for about 1 second if the engine is at a  
normal operating temperature or if the outside temperature is above +5°C. This  
means that you can start the engine right away.  
Do not continue driving if the warning light does not go off although the fluid is at  
the correct level and also the fuse of the fan is in proper order. Contact a specialist  
garage to obtain assistance.  
There is a fault in the glow plug system if the indicator light does not come on  
at all or lights up continuously. Contact a specialist garage as soon as possible to  
obtain assistance.  
Please also refer to the additional instructions ⇒ page 190, “Replenishing the  
coolant”.  
The following text will be displayed in the information display*:  
There is a system fault in the engine control system if the warning light has  
started to flash while driving. The engine management system selects an emer-  
gency programme which enables you to drive to the nearest specialist garage by  
adopting a gentle style of driving.  
STOP CHECK COOLANT SERVICE MANUAL (STOP! CHECK COOLANT!  
OWNER'S MANUAL)  
WARNING  
The following text will be displayed in the information display*:  
•
If you must stop for technical reasons, then park the vehicle at a safe  
distance from the traffic and switch off the engine and switch on the hazard  
ENGINE WORKSHOP! (ENGINE FAULT - WORKSHOP!)  
warning light system ⇒ page 48.  
Coolant temperature, Coolant quantity   
•
Take care when opening the coolant expansion bottle. If the engine is hot,  
the cooling system is pressurized - risk of scalding! It is best to allow the  
engine to cool down before removing the cap.  
1)  
The warning light comes on for a few seconds when the ignition is switched on.  
The coolant temperature is too high or the coolant level too low if the warning light  
does not go out after the engine is started or flashes while driving.  
•
Do not touch the coolant fan! The coolant fan may switch on automati-  
cally even if the ignition is off.  
3 peeps sound as an additional warning signal.  
In this case stop and switch the engine off and check the coolant level; top up the  
coolant as necessary. Please also refer to the additional instructions ⇒ page 190,  
“Replenishing the coolant”.  
Thickness of the brake pads   
If the warning light comes on, contact a specialist garage immediately and have  
the brake pads on all of the wheels inspected.  
Do not continue your journey if for some reason it is not possible under the  
conditions prevailing to top up with coolant. Keep the engine switched off and  
A peep sounds as an additional warning signal.  
The following text will be displayed in the information display*:  
CHECK BRAKE PADS  
1)  
The warning light on vehicles fitted with information display does not come on after  
switching the ignition on, but only if the coolant temperature is too high or the coolant level  
is too low.  
Instruments and Indicator/Warning Lights 27  
The following text will be displayed in the information display*:  
Bonnet   
STOP! OIL PRESS. STOP MOTOR! SERVICE MANUAL (STOP! OIL PRESSURE  
STOP ENGINE! OWNER'S MANUAL)  
The warning light comes on when the ignition is switched on if the bonnet is  
unlocked.  
The warning light lights up yellow* (oil quantity too low)  
If the warning light lights up yellow, there is not the correct quantity of oil in the  
engine. Check as soon as possible the oil level or top up ⇒ page 188 with engine  
Fuel reserve   
oil.  
The warning light comes on, if the fuel level is still below 8 litres.  
A peep sounds as an additional warning signal.  
The following text will be displayed in the information display*:  
PLEASE REFUEL  
A peep sounds as an additional warning signal.  
The following text will be displayed in the information display*:  
CHECK OIL LEVEL  
The warning light will go out if the bonnet is left open for more than 30 seconds. If  
no engine oil has been replenished, the warning light will come on again after  
driving about 100 km.  
Engine oil   
The warning light flashes yellow* (engine oil level sensor faulty)  
The warning light lights up red (low oil pressure)  
A fault on the engine oil level sensor is indicated additionally by an audible signal  
and the warning light coming on several times after the ignition has been switched  
on.  
2)  
The warning light comes on for a few seconds when the ignition is switched on.  
Stop the vehicle and switch the engine off if the warning light does not go off  
after the engine has started or flashes while driving. Check the oil level and top up  
with oil as necessary ⇒ page 188.  
In this case have the engine inspected without delay by a specialist garage.  
The following text will be displayed in the information display*:  
OIL SENSOR WORKSHOP! (OIL SENSOR WORKSHOP)  
3 peeps sound as an additional warning signal.  
Do not continue your journey if for some reason it is not possible under the  
conditions prevailing to top up with oil. Keep the engine switched off and obtain  
professional assistance from a specialist garage, otherwise it could lead to severe  
engine damage.  
WARNING  
•
If you must stop for technical reasons, then park the vehicle at a safe  
distance from the traffic and switch off the engine and switch on the hazard  
Do not drive any further if the warning light remains on even if the oil is at the  
correct level. Do not run the engine not at idling speed either. Contact the nearest  
specialist garage to obtain professional assistance.  
warning light system ⇒ page 48.  
•
The red oil pressure light is not an oil level indicator! One should  
therefore check the oil level at regular intervals, preferably after every refu-  
eling stop.  
2)  
The warning light on vehicles fitted with information display does not come on after  
switching the ignition on, but only if a fault exists or the engine oil level is too low.  
Using the system  
Safety  
Driving Tips  
General Maintenance  
Breakdown assistance  
Technical Data  
28 Instruments and Indicator/Warning Lights  
Open door   
Control system for exhaust   
The warning light comes on if one or several doors are opened or if the boot lid  
The warning light comes on after the ignition has been switched on.  
is opened.  
If the warning light does not go out after starting the engine or it lights up or flashes  
when driving, a fault exists in an exhaust relevant component. The engine manage-  
ment system selects an emergency programme which enables you to drive to the  
nearest specialist garage by adopting a gentle style of driving.  
The warning light on vehicles fitted with information display comes on when  
switching the ignition off. The warning light goes out about 15 seconds after locking  
the vehicle.  
The warning light on vehicles fitted with information display goes out after  
switching the ignition off.  
The following text will be displayed in the information display*:  
EMISSIONS WORKSHOP! (EMISSIONS WORKSHOP)!  
Windshield washer fluid level   
Electronic stability programme (ESP)*   
The warning light comes on when the ignition is switched on if there is insuffi-  
cient fluid in the windshield washer system. Top up the fluid ⇒ page 197.  
The warning light comes on for a few seconds when the ignition is switched on.  
Components of the ESP system also include the Traction Control System (TCS),  
Electronic Differential Lock (EDL), the Antilock Brake System ABS and the braking  
assistant  
A peep sounds as an additional warning signal.  
The following text will be displayed in the information display*:  
TOP UP WASH FLUID  
The warning light comes on when driving when a control cycle is activated.  
The warning light will come on and remains on if the ESP is switched off or if there  
is a fault in the system.  
Light bulbs   
The fact that the ESP system operates together with the ABS means that the ESP  
warning light will also come on if the ABS system is not operating properly.  
The warning light comes on if a light bulb is damaged:  
Further information on the ESP ⇒ page 155, “Electronic stability programme  
(ESP)*”.  
•
•
brakes applied (brake light)  
in lighting (low beam and/or rear light)  
A peep sounds as an additional warning signal.  
Traction control system (TCS) *   
The following text will be displayed in the information display*:  
LIGHTS FAILURE  
or  
The warning light comes on for a few seconds when the ignition is switched on.  
The warning light comes on when driving when a control cycle is activated.  
BRAKE LIGHTS FAILURE  
The warning light will come on and remains on if the TCS is switched off or if there  
is a fault in the system.  
Instruments and Indicator/Warning Lights 29  
The fact that the TCS system operates together with the ABS means that the TCS  
warning light will also come on if the ABS system is not operating properly.  
WARNING  
•
If the brake system warning light comes on together with the ABS  
Further information about the TCS ⇒ page 156, “Traction control system (TCS)*”.  
warning light stop the vehicle immediately and check the brake fluid  
level in the reservoir ⇒ page 191, “Brake fluid”. If the brake fluid level has  
dropped below the MIN marking, do not drive any further - risk of accident!  
Contact a Škoda dealer to obtain professional assistance.  
Antilock brake system (ABS)   
The warning light shows the functionality of the ABS and the Electronic Differ-  
ential Lock (EDL).  
•
Pay attention to the following instructions ⇒ page 185, “Working in the  
engine compartment” before checking the brake fluid level and opening the  
bonnet.  
The warning light comes on for a few seconds after the ignition has been switched  
on or when starting the engine. The warning light goes out after an automatic check  
sequence has been completed.  
•
If the brake fluid is at the correct level, the ABS control function has  
failed. The rear wheels may then block very rapidly when braking. In certain  
circumstances, this can result in the rear end of the car breaking away - risk  
of skidding! Drive carefully to the nearest specialist garage and have the  
fault rectified.  
A fault in the ABS  
The system is not functioning properly if the warning lightdoes not go out within  
a few seconds after switching on the ignition, does not light up at all or lights up  
while driving. The vehicle will only be braked by the normal brake system. Visit a  
specialist garage as quickly as possible and adjust your style of driving in the mean-  
time since you will not know how great the damage is.  
Electronic immobiliser   
Data is compared between the ignition key and the control unit when switching on  
the ignition. The indicator light will light up for a few seconds when ignition key  
authorisation is confirmed.  
Three additional warning tones will sound if there is a major fault in the ABS.  
Further information about ABS ⇒ page 159, “Antilock brake system (ABS)”.  
The warning light will start flashing continuously if a non-authorised ignition key  
(for example the wrong ignition key) has been used. The engine cannot be started  
⇒ page 32.  
A fault in the entire brake system  
If the ABS warning light comes on together with the brake system warning light  
(handbrake must be released), there is a fault not only in the ABS but also in  
another part of the brake system ⇒  
.
It is only possible to start the engine of your car with a Genuine Škoda key with the  
matching code.  
The following text will be displayed in the information display*:  
STOP BRAKE FAULT SERVICE MANUAL (STOP! BRAKE FAULT OWNER'S  
MANUAL)  
Brake system   
Electronic Differential Lock (EDL)  
The warning light flashes or comes on if the brake fluid level is too low, if there  
is a fault in the ABS or if the handbrake is applied.  
The EDL is a part of the ABS. A fault in the EDL is indicated by the ABS warning light  
in the instrument cluster. Have the vehicle inspected without delay by a Škoda  
Service Partner. Further information on the EDL ⇒ page 157, “Electronic Differen-  
tial Lock (EDL)”.  
If the warning light flashes (handbrake is not applied), stop and check the brake  
fluid level ⇒  
.
Using the system  
Safety  
Driving Tips  
General Maintenance  
Breakdown assistance  
Technical Data  
30 Instruments and Indicator/Warning Lights  
The following text will be displayed in the information display*:  
Alternator   
STOP BRAKE FLUID SERVICE MANUAL  
The warning light comes on after the ignition has been switched on. It should go  
out after the engine has started.  
If there is a fault in the ABS which also influences the function of the normal brake  
system (e.g. distribution of brake pressure), the ABS warning light comes on  
together with the brake system warning light . Be aware that not only the ABS but  
If the warning light does not come on after the ignition is switched on, drive to  
the nearest specialist garage.  
also another part of th brake system is defective ⇒  
.
If the warning light does not go out after the engine has started, or comes on when  
driving, drive to the nearest specialist garage. The vehicle battery will be discharged  
in this case so switch off all non-essential electrical components.  
3 peeps sound as an additional warning signal.  
One should get used to high pedal forces, long braking distances and long free play  
of the brake pedal when driving to the next specialist garage.  
The following text will be displayed in the information display*:  
The following text will be displayed in the information display*:  
ALTERNATOR WORKSHOP! (ALTERNATOR WORKSHOP!)  
STOP BRAKE FAULT SERVICE MANUAL (STOP! BRAKE FAULT OWNER'S  
MANUAL)  
Caution  
For further information on the brake system ⇒ page 158, “Brakes”.  
If the warning light comes on when driving and in addition the warning light   
(cooling system fault) also comes on in display, you must then stop the car imme-  
diately and switch the engine off - risk of engine damage!  
Handbrake applied  
The warning light also comes on if the handbrake is applied. An audible warning  
is also given if you drive the vehicle for at least 3 seconds at a speed of more than 5  
km/h.  
Seat belt warning light   
The following text will be displayed in the information display*:  
HANDBRAKE ON  
The warning light comes on for a few seconds after the ignition is switched on as  
a reminder to fasten the seat belt.  
If you do not fasten the seat belt, a long warning signal sounds for 6 seconds.  
For further information on the seat belts ⇒ page 130.  
The following text will be displayed in the information display*:  
FASTEN SEATBELT  
WARNING  
•
Pay attention to the following instructions ⇒ page 185, “Working in the  
engine compartment” before checking the brake fluid level and opening the  
bonnet.  
•
If the brake system warning light does not go out a few seconds after  
For further information on the seat belts ⇒ page 130, “Seat belts”.  
switching on the ignition or comes on when driving, stop immediately and  
check the brake fluid in the reservoir ⇒ page 191, “Brake fluid”. If the fluid  
level has dropped below the MIN marking, do not drive any further - risk of  
accident! Contact a Škoda dealer to obtain professional assistance.  

Related Topics

Using the system
Cockpit Unlocking and locking Lights and Visibility Seats and Stowage Heating and air conditioning system Starting-off and Driving Automatic gearbox Communicating and Navigating

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot