Get Keys and doors -> Arming the system Guide for Subaru Outback SUV Third Generation (2005-2009)

Black plate (107,1)

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

. Opening a door, the rear gate or trunk

lid

. Physical impact to the vehicle, such as

forced entry (only vehicles with shock

sensors (dealer option))

& Activating and deactivating

the alarm system

To change the setting of your vehicle’s

alarm system for activation or deactiva-

tion, do the following.

1. Disarm the alarm system (see “Dis-

arming the system” in this section).

2. Sit in the driver’s seat and shut all

doors (and the rear gate if your vehicle is a

Station wagon).

3. Turn the ignition switch to the “ON”

position.

4. Hold down the UNLOCK side of the

driver’s power door locking switch, open

the driver’s door within the following 1

second, and wait 10 seconds without

releasing the switch. The setting will then

be changed as follows:

If the system was previously activated:

For non-turbo models, the odometer/trip

meter screen displays “AL oF”, and for

turbo models, the multi-information display

shows “Security alarm: OFF” and the horn

sounds twice, indicating that the system is

now deactivated.

If the system was previously deactivated:

For non-turbo models, the odometer/trip

meter screen displays “AL on”, and for

turbo models, the multi-information display

shows “Security alarm: ON” and the horn

sounds once, indicating that the system is

now deactivated.

NOTE

You may have the above setting

change done by your SUBARU dealer.

& If you have accidentally trig-

gered the alarm system

! To stop the alarm

Do any of the following operations:

. Insert the key in the door lock of the

driver’s door and turn it to the unlock

position.

. Press any button on the remote trans-

mitter.

. Turn the ignition switch to the “ON”

position.

& Arming the system

! To arm the system using remote

transmitter

1. Close all windows and the moonroof (if

so equipped).

2. Remove the key from the ignition

switch.

3. Open the doors and get out of the

vehicle.

4. Make sure that the engine hood (and

the trunk lid on the Sedan) are locked.

5. Close all doors (and the rear gate on

the Station wagon).

: Press to Arm the system.

: Press to Disarm the system.

Keys and doors

2-15

– CONTINUED –

Black plate (108,1)

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

2-16 Keys and doors

Turbo models

Non-turbo models

6. Briefly press the “ ” button (for less

than two seconds). All doors (and the rear

gate on the Station wagon) will lock, an

electronic chirp will sound once, the turn

signal lights will flash once, and the

indicator lights will start flashing rapidly.

After rapid flashing for 30 seconds (stand-

by time), the indicator lights will then flash

slowly (twice approximately every two

seconds), indicating that the system has

been armed for surveillance.

If any of the doors, (rear gate or trunk lid)

is not fully closed, an electronic chirp

sounds five times, the turn signal lights

flash five times to alert you that the doors

(or the rear gate) are not properly closed.

When you close the door, the system will

automatically arm and doors will automa-

tically lock.

! To arm the system using power

door locking switches

1. Close all windows.

2. Remove the key from the ignition

switch.

3. Open the doors and get out of the

vehicle.

4. Make sure that the engine hood is

locked.

5. Close the doors (and the rear gate on

the station wagon) but leave only the

driver’s door or the front passenger’s door

open.

6. Push the front side (“LOCK” side) of

the power door locking switch to set the

door locks.

7. Close the door. An electronic chirp will

sound once, the turn signal lights will flash

once and the indicator lights will start

flashing rapidly. After rapid flashing for 30

seconds (standby time), the indicator

lights will then flash slowly (twice approxi-

mately every two seconds), indicating that

the system has been armed for surveil-

lance.

NOTE

. The system can be armed even if the

engine hood, the windows and/or

moonroofs are opened. Always make

sure that they are fully closed before

arming the system.

Black plate (109,1)

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

. The 30-second standby time can be

eliminated if you prefer. Have it per-

formed by your SUBARU dealer.

. If your vehicle is a Sedan and you

unlock the trunk using the remote

transmitter ’s “

” button with the

alarm system armed, the system will

be temporarily placed i n a standby

state. The system will go back to the

surveillanc e state upon locking the

trunk.

. The system is in the standby mode

for a 30-second period after locking the

doors with the remote transmitter. The

security indicator li ght will flash at

short intervals during this period.

. If any of the following actions is

done during the standby period, the

system will not switch to the surveil-

lance state.

. Doors are unlocked using the

remote transmitter.

. Any door (including the rear gate

of a Station wagon or the trunk of a

Sedan) is opened.

. Ignition switch is turned to the

“ON” position.

& Disarming the system

Briefly press the “ ” button (for less than

two seconds) on the remote transmitter.

The driver’s door will unlock, an electronic

chirp will sound twice, the turn signal lights

will flash twice and the indicator light will

go off.

To unlock all other doors and the rear gate

(Station wagon), briefly press the “

”

button a second time within 5 seconds.

NOTE

If the interval between the first and

second presses of the “

” button (for

unlocking of all of the doors and the

rear gate) is extremely short, the sys-

tem may not respond.

Or the system can be disarmed by the

following method, too.

. Insert the key in the door lock of the

driver’s door and turn it to the unlock

position.

! Emergency disarming

If you cannot disarm the system using the

transmitter (i.e. the transmitter is lost,

broken or the transmitter battery is too

weak), you can disarm the system without

using the transmitter.

The system can be disarmed if you turn

the ignition switch from the “LOCK” to the

“ON” position with a registered key.

Insert the key in the door lock of the

driver’s door and turn it to the unlock

position.

& Valet mode

When you choose the valet mode, the

alarm system does not operate. In valet

mode, the remote transmitter is used only

for locking and unlocking the doors and

rear gate (Station wagon) and panic

activation.

To enter the valet mode, change the

setting of your vehicle’s alarm system for

deactivation mode. (Refer to “Activating

and deactivating the alarm system” in this

section.) The security indicator light will

continue to flash once every three sec-

onds indicating that the system is in the

valet mode.

To exit valet mode, change the setting of

your vehicle’s alarm system for activation

mode. (Refer to “Activating and deactivat-

ing the alarm system” in this section.)

& Passive arming

When passive arming mode has been

programmed by the dealer, arming of the

system is automatically accomplished

without using the remote transmitter. Note

Keys and doors 2-17

– CONTINUED –

Keys and doors -> Arming the system for Your Subaru Outback SUV Third Generation (2005-2009)

Related Topics

Popular Owner Manuals

Latest Owner Manuals