Get Instruments and Controls -> 3-2. Push-Button Ignition Switch (Models with Push-Button Start System) Guide for Subaru Outback SUV Sixth Generation (2020-2025)

(174,1)

北米Model "A2620BE-A" EDITED: 2022/ 4/ 25

The light gradually turns off under the

following conditions.

. The ignition switch is turned to the “ON”

position.

. The doors are locked using the remote

keyless entry transmitter.

3-2. Push-Button Ignition

Switch (Models with Push-

Button Start System)

s03bg

& Safety Precautions

s03bg04

Refer to “Safety Precautions” �P118.

& Operating Range for Push-

Button Start System

s03bg01

Legacy

1) Antennas

2) Operating range

Outback/Subaru Outback Wilderness

1) Antennas

2) Operating range

NOTE

. If the access key fob is not detected

within the operating range of the anten-

nas inside the vehicle, the push-button

ignition switch and the engine start

cannot be operated.

. Even when the access key fob is

outside the vehicle, if it is placed too

close to the glass, it may be possible to

switch the power or to start the engine.

. Do not leave the access key fob in

the following places. It may become

impossible to operate the push-button

ignition switch and the engine start.

– On the instrument panel

Push-Button Ignition Switch (Models with Push-Button Start System)

172

(175,1)

北米Model "A2620BE-A" EDITED: 2022/ 4/ 25

– On the floor

– Inside the glove box

– Inside the door trim pocket

– On the rear seat

– On the rear shelf (Legacy)

– Inside the trunk (Legacy)

– At the corner of the cargo area

(Outback/Subaru Outback

Wilderness)

. When operating the push-button

ignition switch or starting the engine,

if the access key fob battery is dis-

charged, perform the procedure de-

scribed in “Access Key Fob – If Access

Key Fob Does Not Operate Properly”

�P496. In such a case, replace the

battery immediately. Refer to “Repla-

cing Battery of Access Key Fob”

�P555.

& Switching Power Status

s03bg02

1) Operation indicator

2) Push-button ignition switch

The power status is switched every time

the push-button ignition switch is pressed.

1. Carry the access key fob, and sit in the

driver’s seat.

2. Make sure the select lever is in the “P”

position.

3. Press the push-button ignition switch

without depressing the brake pedal. Every

time the button is pressed, the power is

switched in the sequence of “OFF”, “ACC”,

“ON” and “OFF”. When the engine is

stopped and the push-button ignition

switch is in “ACC” or “ON”, the operation

indicator on the push-button ignition switch

illuminates in orange.

Power

status

Indicator color Operation

OFF Turned off

Power is turned

off.

ACC Orange

The following

systems can be

used:

audio and ac-

cessory power

outlet.

Orange

(while engine is

stopped)

All electrical

systems can be

used.

Turned off

(while engine is

running)

CAUTION

. To prevent the vehicle battery

from discharging, do not leave

the push-button ignition switch

in the “ON” or “ACC” position for

a long time.

. To avoid a malfunction, observe

the following precautions.

– Do not spill drinks or other

liquids on the push-button

ignition switch.

– CONTINUED –

Push-Button Ignition Switch (Models with Push-Button Start System)

173

Instruments and Controls

(176,1)

北米Model "A2620BE-A" EDITED: 2022/ 4/ 25

– Do not touch the push-button

ignition switch with a hand

that is soiled with oil or other

contaminants.

. If the push-button ignition switch

does not operate smoothly, stop

the operation. Contact a SUBARU

dealer immediately.

. If the operation indicator on the

push-button ignition switch does

not illuminate even when the

instrument panel illumination is

turned on, have the vehicle in-

spected at a SUBARU dealer.

. If the vehicle was left in the hot

sun for a long time, the surface of

the push-button ignition switch

may get hot. Be careful not to

burn yourself.

NOTE

. When operating the push-button

ignition switch, firmly press it all the

way.

. If the push-button ignition switch is

pressed quickly, the power may not

turn on or off.

. If the indicator light on the push-

button ignition switch flashes in green

when the push-button ignition switch is

pressed, steering is locked. When this

occurs, press the push-button ignition

switch while turning the steering wheel

left and right.

! Battery drainage prevention func-

tion

s03bg0201

When the push-button ignition switch is left

in the “ACC” or “ON” position for approxi-

mately 1 hour, the push-button ignition

switch will be automatically switched to

“OFF” to prevent the battery from going

dead. This function is activated when the

select lever is in the “P” position.

& When Access Key Fob Does

Not Operate Properly

s03bg03

Refer to “Access Key Fob – If Access Key

Fob Does Not Operate Properly” �P496.

3-3. Hazard Warning Flasher

s03ab

The hazard warning flasher is used to warn

other drivers when you have to park your

vehicle under emergency conditions. The

hazard warning flasher works with the

ignition switch in any position.

To turn on the hazard warning flasher,

press the hazard warning flasher switch on

the instrument panel. All the turn signal

lights and the turn signal indicator lights

will flash. To turn off the flasher, press the

switch again.

NOTE

When the hazard warning flasher is on,

the turn signals do not work.

Hazard Warning Flasher

174

Instruments and Controls -> 3-2. Push-Button Ignition Switch (Models with Push-Button Start System) for Your Subaru Outback SUV Sixth Generation (2020-2025)

Related Topics

Popular Owner Manuals

Latest Owner Manuals