2022-2026 Subaru XV SUV Ignition switch (models without keyless access) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Ignition switch (models without keyless access) for Your Subaru XV SUV Third Generation (2022-2026)

(139,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
S03
Ignition switch (models without “keyless
access with push-button start system”) ............ 3-4
Key positions......................................................... 3-4
Key reminder chime ............................................... 3-5
Ignition switch light (if equipped) ........................... 3-5
Push-button ignition switch (models with
“keyless access with push-button start
system”) ............................................................... 3-6
Safety precautions ................................................. 3-6
Operating range for push-button start system ........ 3-6
Switching power status.......................................... 3-7
When access key fob does not operate properly .... 3-8
Hazard warning flasher .......................................... 3-8
Meters and gauges ................................................. 3-8
Speedometer ......................................................... 3-8
Tachometer............................................................ 3-8
Odometer............................................................... 3-9
Double trip meter ................................................... 3-9
Fuel gauge............................................................3-10
ECO gauge (if equipped) .......................................3-10
Combination meter settings .................................. 3-11
Illumination brightness control............................ 3-12
Auto dimmer cancel function (if equipped) ............3-12
Warning and indicator .......................................... 3-12
Initial illumination for system check ......................3-12
Seatbelt warning light and chime ..........................3-13
SRS airbag system warning light........................... 3-15
Front passenger’s frontal airbag ON and OFF
indicators ...........................................................3-15
CHECK ENGINE warning light/Malfunction
indicator light ..................................................... 3-15
Engine hood open warning light (if equipped) ....... 3-16
Coolant temperature low indicator light/Coolant
temperature high warning light .......................... 3-16
Charge warning light ............................................ 3-17
Oil pressure warning light..................................... 3-17
Engine low oil level warning light.......................... 3-18
Windshield washer fluid warning light................... 3-18
AT OIL TEMP warning light (CVT models).............. 3-18
Low tire pressure warning light (U.S.-spec.
models) ............................................................. 3-18
ABS warning light................................................. 3-20
Brake system warning light (red) .......................... 3-20
Low fuel warning light .......................................... 3-21
Hill start assist warning light/Hill start assist
OFF indicator light............................................. 3-22
Door open warning light ....................................... 3-22
All-Wheel Drive warning light (CVT models) .......... 3-22
Power steering warning light ................................ 3-22
Vehicle Dynamics Control warning light/Vehicle
Dynamics Control operation indicator light ........ 3-23
Vehicle Dynamics Control OFF indicator light ....... 3-24
Warning chimes and warning indicator of
the keyless access with push-button start
system (if equipped) .......................................... 3-24
Security indicator light.......................................... 3-29
SI-DRIVE indicator light (if equipped) .................... 3-30
Select lever/gear position indicator
(CVT models)..................................................... 3-30
Turn signal indicator lights ................................... 3-31
High beam indicator light...................................... 3-31
High beam assist indicator light (if equipped) ....... 3-31
Cruise control indicator light (if equipped) ............ 3-31
Instruments and controls
3
(140,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Cruise control set indicator light (if equipped) .......3-31
Automatic headlight beam leveler warning light
(models with LED headlights)..............................3-32
LED headlight warning light (models with LED
headlights).......................................................... 3-32
Steering Responsive Headlight warning light/
Steering Responsive Headlight OFF indicator
light (if equipped)................................................ 3-32
Front fog light indicator light (if equipped) ............3-32
Headlight indicator light (if equipped)....................3-32
Auto Start Stop warning light/Auto Start Stop
OFF indicator light (yellow) (if equipped) ............. 3-32
Auto Start Stop indicator light (green)
(if equipped) ....................................................... 3-33
Auto Start Stop No Activity Detected indicator
light (if equipped)................................................ 3-33
X-MODE indicator (if equipped) .............................3-33
Hill descent control indicator (if equipped) ............3-34
BSD/RCTA warning indicator (if equipped).............3-34
BSD/RCTA OFF indicator (if equipped) ..................3-34
RAB warning indicator (if equipped)...................... 3-34
RAB OFF indicator (if equipped)............................ 3-34
Icy road surface warning indicator (if equipped) ....3-34
Combination meter display (color LCD)
(if equipped) ....................................................... 3-35
Basic operation.....................................................3-36
Welcome screen (opening animation) and
Good-bye screen (ending animation) ...................3-36
Warning screen.....................................................3-37
Telltale screen.......................................................3-37
Basic screens .......................................................3-38
Menu screens .......................................................3-41
Multi-function display (black and white)............. 3-43
Driving information display................................... 3-43
Outside temperature indicator............................... 3-48
X-MODE indicator (if equipped) ............................. 3-48
Clock.................................................................... 3-48
Climate control screen.......................................... 3-49
Multi-function display (color LCD)
(if equipped)....................................................... 3-49
Features ............................................................... 3-49
Welcome screen ................................................... 3-50
Self-check screen ................................................. 3-50
Interruption screen ............................................... 3-51
Basic operation .................................................... 3-51
Basic screens....................................................... 3-51
Setting screen ...................................................... 3-58
How to get the source code using the open
source............................................................... 3-65
Clock...................................................................... 3-66
Setting the clock manually.................................... 3-66
Setting the clock automatically ............................. 3-67
Regulatory information ......................................... 3-68
Light control switch ............................................. 3-68
Precautions and tips............................................. 3-68
Headlights ............................................................ 3-69
High/low beam change (dimmer) ........................... 3-71
Headlight flasher .................................................. 3-71
High beam assist function (if equipped) ................ 3-72
Daytime running light system ............................... 3-74
Steering Responsive Headlight (SRH)
(if equipped)....................................................... 3-75
Instruments and controls
(141,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Headlight beam leveler (models with LED
headlights).......................................................... 3-76
Fog light switch (if equipped) .............................. 3-76
Turn signal lever ................................................... 3-77
One-touch lane changer ........................................ 3-78
Wiper and washer ................................................. 3-78
Windshield wiper and washer switches .................3-79
Rear window wiper and washer switch .................. 3-81
Mirrors ................................................................... 3-82
Inside mirror......................................................... 3-82
Auto-dimming mirror/compass (if equipped).......... 3-82
Auto-dimming mirror/compass with HomeLink
®
(if equipped) ...................................................... 3-83
Outside mirrors .................................................... 3-90
Defogger and deicer (if equipped) ...................... 3-91
Tilt/telescopic steering wheel .............................. 3-93
Heated Steering Wheel system (if equipped) ......... 3-93
Horn ....................................................................... 3-94
Instruments and controls
(142,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Ignition switch (models with-
out “keyless access with
push-button start system”)
S03AA
WARNING
. Never turn the ignition switch to
the “LOCK” position while the
vehicle is being driven or towed
because that will lock the steer-
ing wheel, preventing steering
control. And when the engine is
turned off, it takes a much greater
effort than usual to steer.
. Before leaving the vehicle, al-
ways remove the key from the
ignition switch for safety and
never allow an unattended child
to remain in the vehicle. Failure to
follow this procedure could re-
sult in injury to a child or others.
Children could operate the power
windows, the moonroof or other
controls or even make the vehicle
move.
CAUTION
Do not attach a large key holder or
key case to either key. If it banged
against your knees or hands while
you are driving, it could turn the
ignition switch from the “ON” posi-
tion to the “ACC” or “LOCK” posi-
tion, thereby stopping the engine.
Also, if the key is attached to a key
holder or to a large bunch of other
keys, centrifugal force may act on it
as the vehicle moves, resulting in
unwanted turning of the ignition
switch.
The ignition switch has four positions:
LOCK, ACC, ON and START.
NOTE
. Keep the ignition switch in the
“LOCK” position when the engine is
not running.
. Using electrical accessories for a
long time with the ignition switch in the
“ON” or “ACC” position can cause the
battery to go dead.
. If the ignition switch will not move
from the “LOCK” position to the “ACC”
position, turn the steering wheel
slightly to the left and right as you turn
the ignition switch.
& Key positions
S03AA11
Position Description
LOCK
The key can only be inserted
or removed in this position.
The ignition switch will lock
the steering wheel when you
remove the key.
ACC
In this position the electrical
accessories (audio, acces-
sory power outlet, etc.) can be
used.
ON
This is the normal operating
position after starting the en-
gine.
START
The engine is started in this
position.
Instruments and controls/Ignition switch (models without “keyless access with push-button start system”)
3-4
(143,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
CAUTION
Do not turn the ignition switch to the
“START” position while the engine
is running.
NOTE
. To turn the key from the “ACC” to
“LOCK” position, the select lever must
be in the “P” position (CVT models) and
the key must be pushed in and turned.
. If your registered key fails to start
the engine, pull out the key once (the
security indicator light will blink), and
then insert the key again and turn it to
the “START” position again to restart
the engine.
. The engine may not start in the
following cases:
– The key grip is touching another
key or a metallic key holder.
– The key is near another key that
contains an immobilizer transpon-
der.
– The key is near or touching
another transmitter.
& Key reminder chime
S03AA05
The reminder chime sounds when the
driver’s door is opened and the ignition
switch is in the “LOCK” or “ACC” position.
The chime stops under the following
conditions.
. The ignition switch is turned to the “ON”
position.
. The key is removed from the ignition
switch.
. The driver’s door is closed.
& Ignition switch light (if
equipped)
S03AA06
For easy access to the ignition switch in
the dark, the ignition switch light illumi-
nates when the driver’s door is opened or
when the driver’s door is unlocked using
the remote keyless entry transmitter.
The light remains illuminated for several
tens of seconds and then gradually turns
off under the following conditions.
. The driver’s door is closed.
. The doors are unlocked using the
remote keyless entry transmitter.
– CONTINUED –
Instruments and controls/Ignition switch (models without “keyless access with push-button start system”)
3-5
3
(144,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
The light turns off immediately under the
following conditions.
. The ignition switch is turned to the “ON”
position.
. All doors and the rear gate are locked
using the remote keyless entry transmitter.
Push-button ignition switch
(models with “keyless access
with push-button start sys-
tem”)
S03BG
& Safety precautions
S03BG04
Refer to “Safety precautions” F2-3.
& Operating range for push-
button start system
S03BG01
1) Antennas
2) Operating range
NOTE
. If the access key fob is not detected
within the operating range of the anten-
nas inside the vehicle, the push-button
ignition switch and the engine start
cannot be operated.
. Even when the access key fob is
outside the vehicle, if it is placed too
close to the glass, it may be possible to
switch the power or to start the engine.
. Do not leave the access key fob in
the following places. It may become
impossible to operate the push-button
ignition switch and the engine start. It
may also cause a false warning to issue
although no malfunction actually oc-
curs, or not to issue a warning when
any malfunction occurs.
– On the instrument panel
– On the floor
– Inside the glove box
– Inside the door trim pocket
– On the rear seat
– In the cargo area
. When operating the push-button
ignition switch or starting the engine,
if the access key fob battery is dis-
charged, perform the procedure de-
scribed in “Access key fob – if access
key fob does not operate properly” F9-
17. In such a case, replace the battery
immediately. Refer to “Replacing bat-
tery of access key fob” F11-46.
Instruments and controls/Push-button ignition switch (models with “keyless access with push-button start system”)
3-6
(145,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& Switching power status
S03BG02
1) Operation indicator
2) Push-button ignition switch
The power is switched every time the
push-button ignition switch is pressed.
1. Carry the access key fob, and sit in the
driver’s seat.
2. Shift the select lever (CVT models)/the
shift lever (MT models) into the “P”/“N”
position.
3. Press the push-button ignition switch
without depressing the brake pedal. Every
time the button is pressed, the power is
switched in the sequence of “OFF”, “ACC”,
“ON” and “OFF”. When the engine is
stopped and the push-button ignition
switch is in “ACC” or “ON”, the operation
indicator on the push-button ignition switch
illuminates in orange.
Power
status
Indicator color Operation
OFF Turned off
Power is turned
off.
ACC Orange
The following
systems can be
used:
audio and ac-
cessory power
outlet.
ON
Orange
(while engine is
stopped)
All electrical
systems can be
used.
Turned off
(while engine is
running)
CAUTION
. When the push-button ignition
switch is left in “ON” (while the
engine is not running) or “ACC”
for a long time, it may result in
vehicle battery discharge.
. Do not spill drinks or other liquids
on the push-button ignition
switch. It may cause a malfunc-
tion.
. Do not touch the push-button
ignition switch with a hand soiled
with oil or other contaminants. It
may cause a malfunction.
. If the push-button ignition switch
does not operate smoothly, stop
the operation. Contact a SUBARU
dealer immediately.
. If the push-button ignition switch
does not illuminate even when
the instrument panel illumination
is turned on, have the vehicle
inspected at a SUBARU dealer.
. If the vehicle was left in the hot
sun for a long time, the surface of
the push-button ignition switch
may get hot. Be careful not to
burn yourself.
NOTE
. When operating the push-button
ignition switch, firmly press it all the
way.
. If the push-button ignition switch is
pressed quickly, the power may not
turn on or off.
– CONTINUED –
Instruments and controls/Push-button ignition switch (models with “keyless access with push-button start system”)
3-7
3
(146,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
. If the indicator light on the push-
button ignition switch flashes in green
when the push-button ignition switch is
pressed, steering is locked. When this
occurs, press the push-button ignition
switch while turning the steering wheel
left and right.
! Battery drainage prevention func-
tion
S03BG0201
When the push-button ignition switch is left
in the “ACC” or “ON” position for approxi-
mately 1 hour, the push-button ignition
switch will be automatically switched to
“OFF” to prevent the battery from going
dead.
& When access key fob does
not operate properly
S03BG03
Refer to “Access key fob – if access key
fob does not operate properly” F9-17.
Hazard warning flasher
S03AB
The hazard warning flasher is used to warn
other drivers when you have to park your
vehicle under emergency conditions. The
hazard warning flasher works regardless
of the position of the ignition switch.
To turn on the hazard warning flasher,
push the hazard warning flasher switch on
the instrument panel. All the turn signal
lights and the turn signal indicator lights
will flash. To turn off the flasher, push the
switch again.
NOTE
When the hazard warning flasher is on,
the turn signals do not work.
Meters and gauges
S03AD
NOTE
Some of the meters and gauges on the
combination meter use liquid-crystal
displays. You will find their indications
hard to see if you wear polarized
glasses.
& Speedometer
S03AD03
The speedometer shows the vehicle
speed.
& Tachometer
S03AD06
The tachometer shows the engine speed
in thousands of revolutions per minute.
CAUTION
Do not operate the engine with the
pointer of the tachometer in the red
zone. In this range, fuel injection will
be cut by the engine control module
to protect the engine from overrev-
ving. The engine will resume run-
ning normally after the engine speed
is reduced below the red zone.
Instruments and controls/Hazard warning flasher
3-8
(147,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& Odometer
S03AD04
1) TRIP RESET switch
2) Type A combination meter
3) Type B combination meter
This meter displays the odometer when
the ignition switch is in the “ON” position.
The odometer shows the total distance
that the vehicle has been driven.
NOTE
If you press the TRIP RESET switch
when the ignition switch is in the
“LOCK”/“OFF” or “ACC” position, the
odometer/trip meter will light up.
The indicators will turn off when:
. The TRIP RESET switch is not oper-
ated for approximately 10 seconds.
. The driver’s door is opened and then
closed.
& Double trip meter
S03AD05
1) TRIP RESET switch
2) Type A combination meter
3) Type B combination meter
This meter displays the two trip meters
when the ignition switch is in the “ON”
position.
The trip meter shows the distance that the
vehicle has been driven since you last set
it to zero.
The display can be switched as shown in
the following sequence by pressing the
TRIP RESET switch.
To set the trip meter to zero, select the A
trip or B trip meter by pressing the TRIP
RESET switch and keep the knob pressed
for more than 2 seconds.
CAUTION
To ensure safety, do not attempt to
change the function of the indicator
during driving, as an accident could
result.
NOTE
. If the connection between the com-
bination meter and battery is broken for
any reason such as vehicle mainte-
nance or fuse replacement, the data
recorded on the trip meter will be lost.
. If you press the TRIP RESET switch
when the ignition switch is in the
“LOCK”/“OFF” or “ACC” position, the
odometer/trip meter will light up. It is
possible to switch between the A trip
meter and B trip meter indications while
the odometer/trip meter is lit up.
In addition, it is possible to reset the trip
meter by pressing and holding the TRIP
– CONTINUED –
Instruments and controls/Meters and gauges
3-9
3
(148,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
RESET switch.
The indicators will turn off when:
– The TRIP RESET switch is not
operated for approximately 10 sec-
onds.
– The driver’s door is opened and
then closed.
& Fuel gauge
S03AD07
1) TRIP RESET switch
2) Type A combination meter
3) Type B combination meter
The fuel gauge is displayed when the
ignition is in the “ON” position, and it shows
the approximate amount of fuel remaining
in the tank.
The gauge indication may change slightly
during braking, turning or acceleration due
to fuel level movement in the tank.
NOTE
. You will see the “
” sign in the fuel
gauge. This indicates that the fuel filler
lid is located on the right side of the
vehicle.
. If you press the TRIP RESET switch
while the ignition switch is in the
“LOCK”/“OFF” or “ACC” position, the
fuel gauge will light up and indicate the
amount of fuel remaining in the tank.
The indicators will turn off when:
– The TRIP RESET switch is not
operated for approximately 10 sec-
onds.
– The driver’s door is opened and
then closed.
& ECO gauge (if equipped)
S03AD12
1) Type A combination meter
2) Type B combination meter
The ECO gauge shows the difference
between the current rate of fuel consump-
tion and the average rate of fuel consump-
tion since the trip meter was last reset.
If the ECO gauge moves towards the +
side, this indicates better fuel efficiency.
NOTE
. The ECO gauge shows only an
approximate indication of fuel effi-
ciency.
. After resetting the trip meter, the
average rate of fuel consumption is not
shown until you have driven for 1 mile
(or 1 km). Before that time, the ECO
Instruments and controls/Meters and gauges
3-10
(149,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
gauge does not operate.
& Combination meter settings
S03AD16
Meter and vehicle settings can be set on
the combination meter.
! Type A combination meter
S03AD1601
Various adjustments can be made, such
as switching units shown on the combina-
tion meter and adjusting the warning tone
volume.
While the ignition switch is in the “OFF”
position, each press of TRIP RESET
switch results in items shown in the table
below being switched.
Item
Combination
meter display
Possible
settings
A trip
—
B trip
—
Gauge
needle
sweep
function
On/Off
Changing
the unit*
mile/km
Warning
volume*
Lv. 1/Lv. 2/Lv. 3
*: If available
NOTE
. If you switch the units on the combi-
nation meter, the units on the multi-
function display (black and white) also
switches accordingly.
. If either of the following conditions
is met, the combination meter setting
mode will be canceled.
– The driver’s door is opened.
– The TRIP RESET switch is not
operated for approximately 10 sec-
onds or more.
! Switching method
S03AD160101
1. Push the ignition switch in the “OFF”
position.
1) TRIP RESET switch
2. Press the TRIP RESET switch repeat-
edly until the item you want to change is
displayed.
3. Press and hold the TRIP RESET
switch while the item to be changed is
displayed, the setting of the item will be
switched.
! Type B combination meter
S03AD1602
Meter and vehicle settings can be set on
the combination meter display (color
LCD). Refer to “Menu screens” F3-41.
Instruments and controls/Meters and gauges
3-11
3
(150,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Illumination brightness con-
trol
S03AJ
The illumination brightness of the instru-
ment panel illuminates under the following
conditions.
For models without “AUTO” position:
. The light switch is in the “
” or “ ”
position.
For models with “AUTO” position:
. The light switch is in the “
” or “ ”
position when the ambient light is dark.
. The light control switch is in the “AUTO”
position and the headlights illuminate
automatically.
You can adjust the illumination brightness
for better visibility.
To brighten, turn the control dial upward.
To darken, turn the control dial downward.
NOTE
. When the control dial is turned fully
upward, the illumination brightness
becomes the maximum and the auto-
matic dimming function does not work
at all.
. The brightness setting is not can-
celed even when the ignition switch is
turned to the “LOCK”/“OFF” position.
& Auto dimmer cancel function
(if equipped)
S03AJ01
When the ambient light is bright, the
illumination brightness is set to the max-
imum regardless of the position of the
control dial. In this case, you cannot adjust
the illumination brightness by using the
control dial. When the ambient light is dark,
you can dim the illumination brightness as
described above.
The operational/non-operational setting
and sensitivity of the auto dimmer cancel
function can be changed by your SUBARU
dealer. Contact your SUBARU dealer for
details.
Warning and indicator
S03AE
& Initial illumination for system
check
S03AE29
Several of the warning and indicator lights
illuminate when the ignition switch is
initially turned to the “ON” position. This
permits checking the operation of the
bulbs.
Apply the parking brake and turn the
ignition switch to the “ON” position. For
the system check, several of the following
lights illuminate and then turn off after
several seconds or after the engine has
started.
: Seatbelt warning light: The seatbelt
warning light turns off only when the
driver fastens the seatbelt.
: Front passenger’s seatbelt warning
light: The seatbelt warning light turns
off only when the front seat passenger
fastens the seatbelt.
: SRS airbag system warning light
: Front passenger’s frontal airbag ON
indicator
: Front passenger’s frontal airbag
OFF indicator
Instruments and controls/Illumination brightness control
3-12
(151,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
: CHECK ENGINE warning light/Mal-
function indicator light
: Coolant temperature low indicator
light/Coolant temperature high warn-
ing light
: Charge warning light
: Oil pressure warning light
: Engine low oil level warning light
: Windshield washer fluid warning light
: AT OIL TEMP warning light
(CVT models)
: Low tire pressure warning light
(U.S.- spec. models)
/ : ABS warning light
/ : Brake system warning light (red)
: Low fuel warning light
: Hill start assist warning light/Hill start
assist OFF indicator light
: AWD warning light (CVT models)
: Power steering warning light
: Vehicle Dynamics Control warning light/
Vehicle Dynamics Control operation
indicator light
: Vehicle Dynamics Control OFF indicator
light
: Auto Start Stop warning light/Auto Start
Stop OFF indicator light (yellow) (if
equipped)
: Auto Start Stop indicator light (green) (if
equipped)
: Auto Start Stop No Activity Detected
indicator light (if equipped)
If any lights fail to illuminate, it indicates a
burned-out bulb or a malfunction of the
corresponding system.
Consult your authorized SUBARU dealer
for repair.
& Seatbelt warning light
and chime
S03AE01
Your vehicle is equipped with a seatbelt
warning device at the driver’s and front
passenger’s seat, as required by current
safety standards.
With the ignition switch turned to the “ON”
position, this device reminds the driver and
front passenger to fasten their seatbelts by
illuminating the warning lights in the loca-
tions indicated in the following illustration
and sounding a chime.
Driver’s warning light
Front passenger’s warning light
– CONTINUED –
Instruments and controls/Warning and indicator
3-13
3
(152,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! Operation
S03AE0101
If the driver and/or front passenger have/
has not yet fastened the seatbelt(s) when
the ignition switch is turned to the “ON”
position, the seatbelt warning light(s) will
flash for several seconds, to warn that the
seatbelt(s) is/are unfastened. If the driver’s
seatbelt is not fastened, a chime will also
sound simultaneously.
NOTE
. If the driver’s and/or front passen-
ger’s seatbelt(s) are/is still not fastened
6 seconds later, the seatbelt warning
device operates as follows according
to the vehicle speed.
– At speeds lower than approxi-
mately 9 mph (15 km/h)
The warning light(s) for unfastened
seatbelt(s) will alternate between
steady illumination and flashing at
15-second intervals. The chime will
not sound.
– At speeds higher than approxi-
mately 9 mph (15 km/h)
The warning light(s) for unfastened
seatbelt(s) will alternate between
flashing and steady illumination at
15-second intervals and the chime
will sound while the warning light(s)
is/are flashing.
. It is possible to cancel the warning
operation that follows the 6-second
warning after turning ON the ignition
switch. When the ignition switch is
turned ON next time, however, the
complete sequence of the warning
operation resumes. For further details
about canceling the warning operation,
please contact your SUBARU dealer.
If there is no passenger on the front
passenger’s seat, the seatbelt warning
device for the front passenger’s seat will
be deactivated. The front passenger’s
seatbelt warning system monitors whether
or not there is a passenger on the front
passenger’s seat.
Observe the following precautions. Failure
to do so may prevent the device from
functioning correctly or cause the device to
fail.
. Do not install any accessory such as a
table or TV onto the seatback.
. Do not store a heavy load in the
seatback pocket.
. Do not allow the rear seat occupant to
place his/her hands or legs on the front
passenger’s seatback, or allow him/her to
pull the seatback.
. Do not use front seats with their back-
ward-forward position and seatback not
being locked into place securely. If any of
them are not locked securely, adjust them
again. For adjusting procedure, refer to
“Manual seat” F1-5.
If the seatbelt warning device for the front
passenger’s seat does not function cor-
rectly (e.g., it is activated even when the
front passenger’s seat is empty or it is
deactivated even when the front passen-
ger has not fastened his/her seatbelt), take
the following actions.
. Ensure that no article is placed on the
seat other than a child restraint system and
its child occupant, although we strongly
recommend that all children sit in the rear
seat properly restrained.
. Ensure that there is no article left in the
seatback pocket.
. Ensure that the backward-forward po-
sition and seatback of front passenger’s
seat are locked into place securely by
moving the seat back and forth.
If still the seatbelt warning device for front
passenger’s seat does not function cor-
rectly after taking relevant corrective ac-
tions described above, immediately con-
tact your SUBARU dealer for an inspec-
tion.
Instruments and controls/Warning and indicator
3-14
(153,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& SRS airbag system
warning light
S03AE02
WARNING
If the warning light exhibits any of
the following conditions, there may
be a malfunction in the seatbelt
pretensioners and/or SRS airbag
system. Immediately take your vehi-
cle to your nearest SUBARU dealer
to have the system checked. Unless
checked and properly repaired, the
seatbelt pretensioners and/or SRS
airbag will not operate properly in
the event of a collision, which may
increase the risk of injury.
. Flashing or flickering of the warn-
ing light
. No illumination of the warning
light when the ignition switch is
first turned to the “ON” position
. Continuous illumination of the
warning light
. Illumination of the warning light
while driving
For details about the components mon-
itored by the warning light, refer to “SRS
airbag system monitors” F1-68.
& Front passenger’s frontal air-
bag ON and OFF indicators
S03AE03
: Front passenger’s frontal airbag ON
indicator
: Front passenger’s frontal airbag OFF
indicator
The front passenger’s frontal airbag ON
and OFF indicators show you the status of
the front passenger’s SRS frontal airbag.
The indicator is displayed near the map
lights.
When the ignition switch is turned to the
“ON” position, both the ON and OFF
indicators illuminate for 6 seconds during
which time the system is checked. Follow-
ing the system check, both indicators turn
off for 2 seconds. After that, one of the
indicators illuminates depending on the
status of the front passenger’s SRS frontal
airbag determined by the SUBARU ad-
vanced frontal airbag system monitoring.
If the front passenger’s SRS frontal airbag
is activated, the passenger’s frontal airbag
ON indicator will illuminate while the OFF
indicator will remain off.
If the front passenger’s SRS frontal airbag
is deactivated, the passenger’s frontal
airbag ON indicator will remain off while
the OFF indicator will illuminate.
With the ignition switch turned to the “ON”
position, if both the ON and OFF indicators
remain illuminated or off simultaneously
even after the system check period, the
system is malfunctioning. Contact your
SUBARU dealer immediately for an in-
spection.
& CHECK ENGINE warn-
ing light/Malfunction
indicator light
S03AE04
CAUTION
If the CHECK ENGINE light illumi-
nates while you are driving, have
your vehicle checked/repaired by
your SUBARU dealer as soon as
possible. Continued vehicle opera-
tion without having the emission
control system checked and re-
paired as necessary could cause
– CONTINUED –
Instruments and controls/Warning and indicator
3-15
3
(154,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
serious damage, which may not be
covered by your vehicle’s warranty.
If this light illuminates steadily or blinks
while the engine is running, it may indicate
that there is at least one problem or
potential problem somewhere in the emis-
sion control system.
! If the light illuminates steadily
S03AE0401
If the light illuminates steadily while driving
or does not turn off after the engine starts,
an emission control system malfunction
has been detected.
You should have your vehicle checked by
an authorized SUBARU dealer immedi-
ately.
NOTE
This light also illuminates when the fuel
filler cap is not tightened until it clicks.
If you have recently refueled your vehicle,
the cause of the CHECK ENGINE warning
light/malfunction indicator light illuminating
could be a loose or missing fuel filler cap.
Remove the cap and retighten it until it
clicks. Make sure nothing is interfering with
the sealing of the cap. Tightening the cap
will not make the CHECK ENGINE warn-
ing light turn off immediately. It may take
several driving trips. If the light does not
turn off, take your vehicle to your author-
ized SUBARU dealer immediately.
! If the light is blinking
S03AE0402
If the light is blinking while driving, an
engine misfire condition has been de-
tected which may damage the emission
control system.
To prevent serious damage to the emis-
sion control system, you should do the
following.
. Reduce vehicle speed.
. Avoid hard acceleration.
. Avoid steep uphill grades.
. Reduce the amount of cargo, if possi-
ble.
. Stop towing a trailer as soon as
possible.
The CHECK ENGINE warning light may
stop blinking and illuminate steadily after
several driving trips. You should have your
vehicle checked by an authorized
SUBARU dealer immediately.
& Engine hood open
warning light (if
equipped)
S03AE98
The warning light illuminates if the engine
hood is not fully closed. This function is
effective even if the ignition switch is in the
“LOCK”/“OFF” or “ACC” position (all mod-
els) or the key is removed from the ignition
switch (models without “keyless access
with push-button start system”). Always
make sure this light is not illuminated
before you start to drive.
& Coolant temperature
low indicator light/
Coolant temperature
high warning light
S03AE48
CAUTION
. After turning the ignition switch
to the “ON” position, if this
indicator light/warning light be-
haves in any of the following
ways, the electrical system may
be malfunctioning. Contact your
SUBARU dealer immediately for
an inspection.
– It remains blinking in RED.
– It remains illuminated in RED
for more than 2 seconds.
Instruments and controls/Warning and indicator
3-16
(155,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
– It remains blinking in RED and
BLUE alternately.
. While driving, if this indicator
light/warning light behaves in
any of the following ways, take
the specified appropriate mea-
sure listed below.
– Blinking or illuminated in
RED:
Safely stop the vehicle as
soon as possible, and refer to
the emergency steps to take in
the case of engine overheat-
ing. After that, have the sys-
tem checked by your nearest
SUBARU dealer. Refer to “En-
gine overheating” F9-12.
– Blinking in RED and BLUE
alternately:
The electrical system may be
malfunctioning. Contact your
SUBARU dealer for an inspec-
tion.
This coolant temperature low indicator
light/coolant temperature high warning
light has the following three functions.
. Illumination in BLUE indicates insuffi-
cient warming up of the engine
. Blinking in RED indicates that the
engine is close to overheating
. Illumination in RED indicates overheat-
ing condition of the engine
For a system check, this indicator light/
warning light illuminates in RED for ap-
proximately 2 seconds when the ignition
switch is turned to the “ON” position. After
that, this indicator light/warning light
changes to BLUE and maintains illumina-
tion in BLUE. This BLUE illuminated light
turns off when the engine is warmed up
sufficiently.
If the engine coolant temperature in-
creases over the specified range, the
indicator light/warning light blinks in RED.
At this time, the engine is close to over-
heating.
If the engine coolant temperature in-
creases further, the indicator light/warning
light illuminates in RED continuously. At
this time, the engine may be overheating.
When the indicator light/warning light
blinks in RED or illuminates in RED, safely
stop the vehicle as soon as possible, and
refer to the emergency steps to take in the
case of engine overheating. Refer to
“Engine overheating” F9-12. After that,
have the system checked by your nearest
SUBARU dealer.
Also, if the indicator light/warning light
often blinks in RED, the electrical system
may be malfunctioning. Contact your
SUBARU dealer for an inspection.
NOTE
If the engine is restarted after a certain
driving condition, this indicator light/
warning light may illuminate in RED.
However, this is not a malfunction if the
indicator light/warning light turns off
after a short time.
& Charge warning light
S03AE05
If this light illuminates when the engine is
running, it may indicate that the charging
system is not working properly.
If the light illuminates while driving or does
not turn off after the engine starts, stop the
engine at the first safe opportunity and
check the alternator belt. If the belt is
loose, broken or if the belt is in good
condition but the light remains illuminated,
contact your nearest SUBARU dealer
immediately.
& Oil pressure warning
light
S03AE06
If this light illuminates when the engine is
running, it may indicate that the engine oil
pressure is low and the lubricating system
– CONTINUED –
Instruments and controls/Warning and indicator
3-17
3
(156,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
is not working properly.
If the light illuminates while driving or does
not turn off after the engine starts, stop the
engine at the first safe opportunity and
contact your nearest SUBARU dealer
immediately.
CAUTION
Do not operate the engine with the
oil pressure warning light illumi-
nated. This may cause serious en-
gine damage.
& Engine low oil level
warning light
S03AE58
This light illuminates when the engine oil
level decreases to the lower limit.
If the warning light illuminates, check the
engine oil level on a level surface. When
the engine oil level is not within the normal
range, refill with engine oil. Refer to
“Engine oil” F11-8. After adding or chan-
ging the engine oil, warm up the engine
and stop it on a level surface, then start the
engine after a lapse of 1 minute or more.
Confirm that the warning light has turned
off after the engine has started. If the
warning light does not turn off after refilling
the engine oil, or the light illuminates even
though the engine oil level is within the
normal range, have the vehicle checked by
a SUBARU dealer.
NOTE
. The oil level will be detected by the
system just after turning the ignition
switch to the OFF position. If the oil
level is below the lower limit when the
ignition switch is turned to the ON
position, the engine low oil level warn-
ing light will turn on.
. When the vehicle is parked on a
steep slope, the engine low oil level
warning light may not illuminate even if
the oil level is below the lower limit to
avoid erroneous lighting.
& Windshield washer
fluid warning light
S03AE42
This light illuminates when the fluid level in
the windshield washer fluid tank de-
creases to the lower limit (approximately
0.6 US qt, 0.6 liter, 0.5 Imp qt).
& AT OIL TEMP warning
light (CVT models)
S03AE07
If this light illuminates when the engine is
running, it may indicate that the transmis-
sion fluid temperature is too hot.
If the light illuminates while driving, im-
mediately stop the vehicle in a safe place
and let the engine idle until the warning
light turns off.
! Transmission control system warn-
ing
S03AE0701
If the “AT OIL TEMP” warning light flashes
after the engine has started, it may indicate
that the transmission control system is not
working properly. Contact your nearest
SUBARU dealer for service immediately.
& Low tire pressure
warning light (U.S.-
spec. models)
S03AE08
When the ignition switch is turned to the
“ON” position, the low tire pressure warn-
ing light will illuminate for approximately 2
seconds to check that the tire pressure
monitoring system (TPMS) is functioning
properly. If there is no problem and all tires
are properly inflated, the light will turn off.
Each tire, including the spare (if provided),
should be checked monthly when cold and
inflated to the inflation pressure recom-
mended by the vehicle manufacturer on
the vehicle placard or tire inflation pres-
sure label. (If your vehicle has tires of a
different size than the size indicated on the
vehicle placard or tire inflation pressure
label, you should determine the proper tire
inflation pressure for those tires.)
Instruments and controls/Warning and indicator
3-18
(157,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
As an added safety feature, your vehicle
has been equipped with a tire pressure
monitoring system (TPMS) that illuminates
a low tire pressure telltale when one or
more of your tires is significantly under-
inflated. Accordingly, when the low tire
pressure telltale illuminates, you should
stop and check your tires as soon as
possible, and inflate them to the proper
pressure. Driving on a significantly under-
inflated tire causes the tire to overheat and
can lead to tire failure. Under-inflation also
reduces fuel efficiency and tire tread life,
and may affect the vehicle’s handling and
stopping ability.
Please note that the TPMS is not a
substitute for proper tire maintenance,
and it is the driver’s responsibility to
maintain correct tire pressure, even if
under-inflation has not reached the level
to trigger illumination of the TPMS low tire
pressure telltale.
Your vehicle has also been equipped with
a TPMS malfunction indicator to indicate
when the system is not operating properly.
The TPMS malfunction indicator is com-
bined with the low tire pressure telltale.
When the system detects a malfunction,
the telltale will flash for approximately one
minute and then remain continuously
illuminated. This sequence will continue
upon subsequent vehicle start-ups as long
as the malfunction exists. When the mal-
function indicator is illuminated, the sys-
tem may not be able to detect or signal low
tire pressure as intended. TPMS malfunc-
tions may occur for a variety of reasons,
including the installation of replacement or
alternate tires or wheels on the vehicle that
prevent the TPMS from functioning prop-
erly. Always check the TPMS malfunction
telltale after replacing one or more tires or
wheels on your vehicle to ensure that the
replacement or alternate tires and wheels
allow the TPMS to continue to function
properly.
Should the warning light illuminate steadily
after blinking for approximately one min-
ute, have the system inspected by your
nearest SUBARU dealer as soon as
possible.
WARNING
If this light does not illuminate
briefly after the ignition switch is
turned ON or the light illuminates
steadily after blinking for approxi-
mately one minute, you should have
your Tire Pressure Monitoring Sys-
tem checked at a SUBARU dealer as
soon as possible.
If this light illuminates while driving,
never brake suddenly and keep
driving straight ahead while gradu-
ally reducing speed. Then slowly
pull off the road to a safe place.
Otherwise an accident involving
serious vehicle damage and serious
personal injury could occur.
If this light still illuminates while
driving after adjusting the tire pres-
sure, a tire may have significant
damage and a fast leak that causes
the tire to lose air rapidly. If you have
a flat tire, replace it with a spare tire
as soon as possible.
When a spare tire is mounted or a
wheel rim is replaced without the
original pressure sensor/transmitter
being transferred, the Low tire pres-
sure warning light will illuminate
steadily after blinking for approxi-
mately one minute. This indicates
the TPMS is unable to monitor all
four road wheels. Contact your
SUBARU dealer as soon as possible
for tire and sensor replacement and/
or system resetting.
If the light illuminates steadily after
blinking for approximately one min-
ute, promptly contact a SUBARU
dealer to have the system inspected.
– CONTINUED –
Instruments and controls/Warning and indicator
3-19
3
(158,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
CAUTION
The tire pressure monitoring system
is NOT a substitute for manually
checking tire pressure. The tire
pressure should be checked peri-
odically (at least monthly) using a
tire gauge. After any change to tire
pressure(s), the tire pressure mon-
itoring system will not re-check tire
inflation pressures until the vehicle
is first driven more than 20 mph (32
km/h). After adjusting the tire pres-
sures, increase the vehicle speed to
at least 20 mph (32 km/h) to start the
TPMS re-checking of the tire infla-
tion pressures. If the tire pressures
are now above the severe low pres-
sure threshold, the low tire pressure
warning light should turn off a few
minutes later. Therefore, be sure to
install the specified size for the front
and rear tires.
& ABS warning light
S03AE09
CAUTION
. If any of the following conditions
occur, we recommend that you
have the ABS repaired at the first
available opportunity by your
SUBARU dealer.
– The warning light does not
illuminate when the ignition
switch is turned to the “ON”
position.
– The warning light illuminates
when the ignition switch is
turned to the “ON” position,
but it does not turn off even
after the vehicle is started.
– The warning light illuminates
during driving.
. When the warning light is on (and
the brake system warning light is
off), the ABS function shuts
down. However, the conventional
brake system continues to oper-
ate normally.
The ABS warning light, Vehicle Dynamics
Control warning light, and brake system
warning light illuminate simultaneously if
the EBD system malfunctions. For further
details of the EBD system malfunction
warning, refer to “Electronic Brake Force
Distribution (EBD) system warning” F3-
21.
NOTE
If the warning light behavior is as
described in the following conditions,
the ABS may be considered normal.
. The warning light illuminates when
the ignition switch is turned to the “ON”
position and turns off approximately 2
seconds after the engine has started.
. The warning light illuminates right
after the engine is started but turns off
immediately, remaining off.
. The warning light remains illumi-
nated after the engine has been started,
but it turns off while driving.
. The warning light illuminates during
driving, but it turns off immediately and
remains off.
When driving with an insufficient battery
voltage such as when the engine is jump
started, the ABS warning light may illumi-
nate. This is due to the low battery voltage
and does not indicate a malfunction. When
the battery becomes fully charged, the
light will turn off.
& Brake system
warning light (red)
S03AE10
This light illuminates with the parking
brake applied while the ignition switch is
in the “ON” position. It turns off when the
parking brake is fully released.
WARNING
. Driving with the brake system
Instruments and controls/Warning and indicator
3-20
(159,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
warning light on is dangerous.
This indicates your brake system
may not be working properly. If
the light remains illuminated,
have the brakes inspected by a
SUBARU dealer immediately.
. If at all in doubt about whether the
brakes are operating properly, do
not drive the vehicle. Have your
vehicle towed to the nearest
SUBARU dealer for repair.
The brake system warning light has the
following functions.
! Brake fluid level warning
S03AE1002
This light illuminates when the brake fluid
level has dropped to near the “MIN” level of
the brake fluid reservoir with the ignition
switch in the “ON” position and with the
parking brake fully released.
If the brake system warning light should
illuminate while driving (with the parking
brake fully released and with the ignition
switch positioned in “ON”), it could be an
indication of leaking of brake fluid or worn
brake pads. If this occurs, immediately
stop the vehicle at the nearest safe
location and check the brake fluid level. If
the fluid level is below the “MIN” mark in
the reservoir, do not drive the vehicle.
Have the vehicle towed to the nearest
SUBARU dealer for repair.
! Electronic Brake Force Distribution
(EBD) system warning
S03AE1003
The EBD system may be malfunctioning if
the brake system warning light
/ ,
Vehicle Dynamics Control warning light
and ABS warning light / illuminate
simultaneously during driving.
Even if the EBD system fails, the conven-
tional braking system will still function.
However, the rear wheels will be more
prone to locking when the brakes are
applied harder than usual and the vehicle’s
motion may therefore become somewhat
harder to control.
If the brake system warning light
/ ,
Vehicle Dynamics Control warning light
and ABS warning light / illuminate
simultaneously, take the following steps.
1. Stop the vehicle in the nearest safe, flat
location.
2. Shut down the engine, apply the
parking brake and then restart it.
3. Fully release the parking brake.
4. Even if all the warning lights do not
come back on, the EBD system may have
a possible malfunction. Drive carefully to
the nearest SUBARU dealer and have the
system inspected.
5. If all the warning lights stay illuminated
or come back on after approximately 2
seconds, shut down the engine, apply the
parking brake and check the brake fluid
level.
. If the brake fluid level is not below the
“MIN” mark, the EBD system may be
malfunctioning. Drive carefully to the
nearest SUBARU dealer and have the
system inspected.
. If the brake fluid level is below the “MIN”
mark, DO NOT drive the vehicle. Instead,
have the vehicle towed to the nearest
SUBARU dealer for repair.
! Vacuum pressure system warning
S03AE1006
The brake system warning light / will
illuminate when the vacuum pressure
sensor is malfunctioning or brake booster
pressure is decreasing.
If the brake warning light continues to
illuminate for several minutes after starting
the engine, there may be a malfunction in
the vacuum system. In this case, drive the
vehicle carefully and have the system
inspected by a SUBARU dealer.
& Low fuel warning light
S03AE11
The low fuel warning light illuminates when
the tank is nearly empty, at approximately
2.5 US gal (9.5 liters, 2.1 Imp gal). It only
operates when the ignition switch is in the
“ON” position.
– CONTINUED –
Instruments and controls/Warning and indicator
3-21
3
(160,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
CAUTION
Promptly put fuel in the tank when-
ever the low fuel warning light
illuminates. Engine misfires as a
result of an empty tank could cause
damage to the engine.
& Hill start assist warning
light/Hill start assist
OFF indicator light
S03AE47
! Hill start assist warning light
S03AE4701
While the engine is running, if there are
any malfunctions in the Hill start assist
system, the warning light will illuminate.
WARNING
When the Hill start assist warning
light illuminates, have the vehicle
inspected at an authorized SUBARU
dealer.
! Hill start assist OFF indicator light
S03AE4702
While the Hill start assist system is
deactivated, the Hill start assist OFF
indicator light illuminates continuously to
inform the driver that the Hill start assist
system is not operational.
& Door open warning
light
S03AE12
The warning light illuminates if any door or
the rear gate is not fully closed. This
function is effective even if the ignition
switch is in the “LOCK”/“OFF” or “ACC”
position, or the key is removed from the
ignition switch.
For some models, only the open doors are
indicated by the warning lights.
Always make sure this light is not illumi-
nated before you start to drive.
& All-Wheel Drive warn-
ing light (CVT models)
S03AE13
This light blinks if the vehicle is driven with
tires of differing diameters fitted on the
wheels or with an excessively low air
pressure in any of the tires.
WARNING
If the AWD warning light flashes,
promptly park in a safe location then
check whether all four tires are the
same diameter and whether any of
the tires has a puncture or has lost
air pressure for some other reason.
Continuing to drive with the AWD
warning light flashing can lead to
powertrain damage.
NOTE
If the temporary spare tire is used, the
AWD warning light may flash. Use of the
temporary spare tire should therefore
be restricted to the minimum time
necessary. Replace the temporary
spare tire with a conventional tire as
soon as possible.
& Power steering warning
light
S03AE53
While the engine is running, this warning
light illuminates when a malfunction has
been detected in the electric power steer-
ing system.
CAUTION
When the power steering warning
light is illuminated, there may be
more resistance when the steering
wheel is operated. Drive carefully to
the nearest SUBARU dealer and
have the vehicle inspected immedi-
ately.
Instruments and controls/Warning and indicator
3-22
(161,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
NOTE
If the steering wheel is operated in the
following ways, the power steering
control system may temporarily limit
the power assist in order to prevent the
system components, such as the con-
trol computer and drive motor, from
overheating.
. The steering wheel is operated fre-
quently and turned sharply while the
vehicle is maneuvered at extremely low
speeds, such as while frequently turn-
ing the steering wheel during parallel
parking.
. The steering wheel remains in the
fully turned position for a long period of
time.
At this time, there will be more resis-
tance when steering. However this is
not a malfunction. Normal steering
force will be restored after the steering
wheel is not operated for a while and
the power steering control system has
an opportunity to cool down. However,
if the power steering is operated in a
non-standard way which causes power
assist limitation to occur too frequently,
that may result in a malfunction of the
power steering control system.
& Vehicle Dynamics Con-
trol warning light/Vehi-
cle Dynamics Control
operation indicator
light
S03AE14
! Vehicle Dynamics Control warning
light
S03AE1401
CAUTION
The Vehicle Dynamics Control sys-
tem provides its ABS control
through the electrical circuit of the
ABS. Accordingly, if the ABS is
inoperative, the Vehicle Dynamics
Control system becomes unable to
provide ABS control. As a result, the
Vehicle Dynamics Control system
also becomes inoperative, causing
the warning light to illuminate.
Although both the Vehicle Dynamics
Control system and ABS are inop-
erative in this case, the ordinary
functions of the brake system are
still available. You will be safe while
driving with this condition, but drive
carefully and have your vehicle
checked at a SUBARU dealer as
soon as possible.
NOTE
. If the electrical circuit of the Vehicle
Dynamics Control system itself mal-
functions, the warning light only illumi-
nates. At this time, the ABS (Anti-lock
Brake System) remains fully opera-
tional.
. The warning light illuminates when
the electronic control system of the
ABS/Vehicle Dynamics Control system
malfunctions.
. The Vehicle Dynamics Control warn-
ing light, ABS warning light, and brake
system warning light illuminate simul-
taneously if the EBD system malfunc-
tions. For further details of the EBD
system malfunction warning, refer to
“Electronic Brake Force Distribution
(EBD) system warning” F3-21.
The Vehicle Dynamics Control system is
probably inoperative under any of the
following conditions. Have your vehicle
checked at a SUBARU dealer immedi-
ately.
. The warning light does not illuminate
when the ignition switch is turned to the
“ON” position.
. The warning light illuminates while the
vehicle is running.
– CONTINUED –
Instruments and controls/Warning and indicator
3-23
3
(163,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
on the combination meter in order to
minimize improper operations and help
protect your vehicle from theft.
When the warning chime sounds and/or
the warning indicator flashes, take the
appropriate action.
WARNING
Never drive the vehicle if the indica-
tor on the push-button ignition
switch is flashing in green when
starting the engine. This indicates
the status that the steering wheel is
not released and could result in an
accident involving serious injury or
death.
CAUTION
. When starting the engine again
after the operation indicator on
the push-button ignition switch
flashes in green, if the operation
indicator is still flashing in green,
there could be a steering lock
malfunction. Contact your
SUBARU dealer as soon as pos-
sible.
. When the operation indicator on
the push-button ignition switch
flashes in orange, contact a
SUBARU dealer immediately.
NOTE
. Even when the access key fob is
within the operating ranges inside the
vehicle, the access key warning for
engine start may be provided depend-
ing on the status of the access key fob
and the environmental conditions.
. When the access key fob is taken out
of the vehicle through an open window,
the access key fob takeout warning or
passenger access key fob takeout
warning will not be provided.
! List of warnings
S03AE5504
CAUTION
When any of the following warnings
occurs even if the access key warn-
ing indicator does not appear, take
the appropriate action.
– CONTINUED –
Instruments and controls/Warning and indicator
3-25
3
(164,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Inside warning
chime
Outside warning
chime
Operation indicator
on push-button igni-
tion switch
Status Action
Ding, ding ...
(intermittent)
— —
The driver’s door was opened while the
push-button ignition switch is “ACC” (in
CVT models, when the select lever is in
the “P” position).
Switch the push-button ignition switch to
“OFF”, or close the driver’s door.
When exiting the vehicle, be sure to
switch the push-button ignition switch to
“OFF”.
The push-button ignition switch was
switched to “OFF” while the driver’s door
is open.
Close the driver’s door.
Ding
Short beep
(2 seconds)
—
Lockout warning:
An attempt was made to lock all doors
while the access key fob is left inside the
vehicle.
Take out the access key fob from the
vehicle, and lock the doors.
The doors cannot be locked while the
access key fob is inside the vehicle.
A chirp sound will be heard, and all doors
will be unlocked.
—
Short beep
(2 seconds)
—
Access key fob lock-in warning:
The door lock sensor was touched while
the push-button ignition switch is “OFF”
and the access key fob is inside the
vehicle.
Take out the access key fob from the
vehicle, and lock the doors.
If the access key fob is inside the vehicle,
the doors cannot be locked.
—
Beep, beep, beep,
beep, beep
(5 times)
—
Door ajar warning:
The door lock sensor is touched while the
ignition switch is in the “OFF” position and
one of the doors including the rear gate is
opened.
Close the doors securely and lock them.
If one of the doors including the rear gate
is opened, the doors cannot be locked.
Ding
Long beep (60
seconds max.)
—
Power warning:
The door lock sensor was touched while
carrying the access key fob, the push-
button ignition switch is in a position other
than “OFF” (in CVT models, when the
select lever is in the “P” position).
Return the access key fob inside the
vehicle, or switch the push-button ignition
switch to “OFF”.
If the push-button ignition switch is not
switched to “OFF”, the doors cannot be
locked.
Ding, ding ...
(7 seconds)
— —
Access key warning:
The vehicle was driven while the access
key fob is not inside the vehicle.
Carry the access key fob, and drive the
vehicle.
Instruments and controls/Warning and indicator
3-26
(165,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Inside warning
chime
Outside warning
chime
Operation indicator
on push-button igni-
tion switch
Status Action
Ding — —
Access key warning for engine start:
The push-button ignition switch was
pressed while the access key fob is not
inside the vehicle.
Carry the access key fob, and press the
push-button ignition switch.
Ding
Beep, beep, beep
(3 times)
—
Access key takeout warning:
The driver exited the vehicle with the
access key fob and closed the driver’s
door while the push-button ignition switch
is in a position other than “OFF” (in CVT
models, when the select lever is in the “P”
position).
Switch the push-button ignition switch to
“OFF”, and get out of the vehicle.
Ding
Beep, beep, beep
(3 times)
—
Passenger access key takeout warn-
ing:
A fellow passenger exited the vehicle with
the access key fob and closed a door
other than the driver’s door while the
push-button ignition switch is in a position
other than “OFF”.
Return the access key fob to inside the
vehicle, or switch the push-button ignition
switch to “OFF”.
Long beep
(continuous)
Long beep
(continuous)
—
Access key takeout without P position
warning (CVT models):
The driver exited the vehicle with the
access key fob and closed the driver’s
door while the push-button ignition switch
is in a position other than “OFF” and the
select lever is in a position other than the
“P” position.
Shift the select lever to the “P” position,
switch the push-button ignition switch to
“OFF” and exit the vehicle.
Long beep
(continuous)
— —
Select lever position warning (CVT
models):
The engine is turned off by pressing the
push-button ignition switch and the select
lever is in a position other than the “P”
position.
Start the engine, shift the select lever to
the “P” position, switch the push-button
ignition switch to “OFF” and exit the
vehicle.
– CONTINUED –
Instruments and controls/Warning and indicator
3-27
3
(166,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Inside warning
chime
Outside warning
chime
Operation indicator
on push-button igni-
tion switch
Status Action
Long beep
(continuous)
— —
Select lever position warning (CVT
models):
The driver’s door was opened while the
push-button ignition switch is in a position
other than “OFF” and the select lever is in
a position other than the “P” position.
Shift the select lever to the “P” position,
switch the push-button ignition switch to
“OFF” and exit the vehicle.
Ding — — The battery of the access key fob is low. Replace the battery of the access key fob.
Ding —
Flashes in green
(15 seconds max.)
Steering lock warning:
The engine start procedure was per-
formed, but the steering is still locked.
While turning the steering wheel right and
left lightly, depress the brake pedal and
press the push-button ignition switch.
Ding —
Flashes in orange
(15 seconds max.)
System malfunction warning:
A malfunction was detected in the power
system or steering lock.
Contact a SUBARU dealer immediately
and have the vehicle inspected.
Instruments and controls/Warning and indicator
3-28
(167,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& Security indicator light
S03AE16
This indicator light shows the status of the
alarm system. It also indicates operation of
the immobilizer system.
! Alarm system
S03AE1601
It blinks to show the driver the operational
status of the alarm system. For detailed
information, refer to “Alarm system” F2-
25.
! Immobilizer system
S03AE1602
The security indicator light starts blinking
in the following conditions.
For models with “keyless access with
push-button start system”:
. Immediately after the push-button igni-
tion switch is turned to the “OFF” position.
. Immediately after the driver’s door is
opened or closed when all of the following
conditions are met.
– The push-button ignition switch is in
the “ON” or “ACC” position.
– The engine is not running.
In the event that an unauthorized key is
used (for example, the key is unregistered
or the ID code does not match), the power
is not switched to “ON” and the security
indicator light continues blinking.
For models without “keyless access
with push-button start system”:
. Immediately after the key is pulled out.
. Approximately 60 seconds after the
ignition switch is turned from the “ON”
position to the “ACC” or “LOCK” position.
If the indicator light does not blink in the
above conditions, it may indicate that
immobilizer system may be malfunction-
ing. Contact your nearest SUBARU dealer
immediately.
In the event that an unauthorized key (for
example, an unauthorized duplicate) is
used to start the engine, the security
indicator light illuminates. For details about
the immobilizer system, refer to “Immobi-
lizer” F2-15.
NOTE
. The security indicator light remains
off in the following conditions. It means
that the matching of the ID code is
completed and the immobilizer system
is deactivated, and it does not indicate
a malfunction.
Models with “keyless access with
push-button start system”:
– While the engine is running
– The push-button ignition switch
has been turned to the “ON” or
“ACC” position and the driver’s
door has not been opened or closed
Models without “keyless access
with push-button start system”:
– While the engine is running
– When the ignition switch is in the
“ON” position
– For approximately 60 seconds
after the ignition switch is turned
from the “ON” position to the “ACC”
or “LOCK” position
. Even if a malfunction occurs, such
as the security indicator light flashes
irregularly, it will not affect the func-
tionality of the immobilizer system.
– CONTINUED –
Instruments and controls/Warning and indicator
3-29
3
(168,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& SI-DRIVE indicator light (if
equipped)
S03AE52
Type A
1) Intelligent (I) mode indicator
2) Sport (S) mode indicator
Type B
1) Intelligent (I) mode indicator
2) Sport (S) mode indicator
This light indicates the current SI-DRIVE
mode.
For details of SI-DRIVE mode, refer to “SI-
DRIVE” F7-32.
& Select lever/gear position in-
dicator (CVT models)
S03AE43
Type A
1) Upshift indicator
2) Downshift indicator
3) Select lever/gear position indicator
Instruments and controls/Warning and indicator
3-30
(169,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Type B
1) Upshift indicator
2) Downshift indicator
3) Select lever/gear position indicator
This indicator shows the position of the
select lever.
For models with manual mode, when the
manual mode is selected, the gear position
indicator (which shows the current gear
selection) and the upshift/downshift indi-
cator light up. Refer to “Continuously
variable transmission” F7-25.
& Turn signal indicator
lights
S03AE20
These lights show the operation of the turn
signal or lane change signal.
If the indicator lights do not blink or blink
rapidly, the turn signal bulb may be burned
out. Replace the bulb as soon as possible.
Refer to “Replacing bulbs” F11-38.
& High beam indicator
light
S03AE21
This light shows that the headlights are in
the high beam mode.
This indicator light also illuminates when
the headlight flasher is operated.
& High beam assist indi-
cator light (if equipped)
S03AE83
This light illuminates when the high beam
assist function is activated. For details
about the high beam assist function, refer
to “High beam assist function” F3-72.
& Cruise control indicator
light (if equipped)
S03AE22
This light illuminates when the cruise
control main button is pressed to activate
the cruise control function. For details,
refer to “To set cruise control” F7-52.
If this light blinks, do not use the cruise
control. In addition, if it blinks frequently,
contact your SUBARU dealer for an
inspection.
CAUTION
If the CHECK ENGINE warning light/
malfunction indicator light illumi-
nates, the cruise control indicator
light flashes at the same time. At this
time, avoid driving at high speed and
have your vehicle inspected at a
SUBARU dealer as soon as possi-
ble.
& Cruise control set indi-
cator light (if equipped)
S03AE23
This light illuminates when vehicle speed
has been set to use the cruise control
function. Refer to “To set cruise control”
F7-52.
– CONTINUED –
Instruments and controls/Warning and indicator
3-31
3
(170,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& Automatic headlight
beam leveler warning
light (models with LED
headlights)
S03AE33
This light illuminates when the automatic
headlight beam leveler does not operate
normally.
If this light illuminates during driving, have
your vehicle inspected at your SUBARU
dealer.
& LED headlight warning
light (models with LED
headlights)
S03AE76
This light illuminates if the LED headlights
malfunction. Have your vehicle inspected
at a SUBARU dealer as soon as possible.
& Steering Responsive
Headlight warning light/
Steering Responsive
Headlight OFF indicator
light (if equipped)
S03AE89
This light illuminates when the Steering
Responsive Headlight OFF switch is
pressed to deactivate the Steering Re-
sponsive Headlight. Also, the light flashes
when a malfunction occurs in the Steering
Responsive Headlight. Refer to “Steering
Responsive Headlight (SRH)” F3-75.
& Front fog light indicator
light (if equipped)
S03AE25
This indicator light illuminates while the
front fog lights are illuminated.
& Headlight indicator
light (if equipped)
S03AE24
This indicator light illuminates under the
following conditions.
. The light switch is turned to the “
” or
“
” position.
. The light control switch is in the “AUTO”
position and the headlights illuminate
automatically.
& Auto Start Stop warning
light/Auto Start Stop
OFF indicator light (yel-
low) (if equipped)
S03AE65
! Auto Start Stop warning light (yel-
low)
S03AE6501
CAUTION
. If the Auto Start Stop warning
light is flashing in yellow, there
may be a malfunction in the Auto
Start Stop system. We recom-
mend that you have your vehicle
inspected at a SUBARU author-
ized dealer as soon as possible.
. If the Auto Start Stop warning
light is illuminated in yellow at
any time other than in the follow-
ing cases and will not turn off
even if the Auto Start Stop OFF
switch is pushed and held, we
recommend that you have your
vehicle inspected at a SUBARU
dealer as soon as possible.
The Auto Start Stop warning light will
illuminate in yellow if you open the engine
hood when the engine has been tempora-
rily stopped by the Auto Start Stop system.
In this case, to ensure safety, the engine
will not be automatically restarted, even if
you release the brake pedal. Use normal
operation to restart the engine.
! Auto Start Stop OFF indicator light
(yellow)
S03AE6502
This light will illuminate in yellow when the
Auto Start Stop OFF switch is pressed to
prevent the Auto Start Stop system from
operating. It will turn off when the Auto
Start Stop OFF switch is pressed once
more to enable operation of the Auto Start
Stop system.
Instruments and controls/Warning and indicator
3-32
(171,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& Auto Start Stop indica-
tor light (green) (if
equipped)
S03AE66
This indicator light illuminates when the
engine has been temporarily stopped by
the Auto Start Stop system. It will turn off
when the engine is restarted.
& Auto Start Stop No
Activity Detected indi-
cator light (if equipped)
S03AEA3
When a vehicle is stopped, the indicator
light illuminates when the operating con-
dition of idling stop are not meet. The light
will turn off when the vehicle starts driving.
& X-MODE indicator (if
equipped)
S03AE68
! Type A combination meter
S03AE6801
X-MODE indicator
! Type B combination meter
S03AE6802
X-MODE indicator (models with 1 mode)
X-MODE indicator (models with 2 modes)
1) DEEP SNOW·MUD mode indicator
2) SNOW·DIRT mode indicator
This indicator appears while the X-MODE
– CONTINUED –
Instruments and controls/Warning and indicator
3-33
3
(172,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
is activated. It will disappear when the X-
MODE is deactivated. Refer to “To acti-
vate/deactivate the X-MODE” F7-43.
& Hill descent control in-
dicator (if equipped)
S03AE69
This indicator appears while the hill des-
cent control function is in standby. It will
flash while the hill descent control function
is operating. It will disappear when the hill
descent control function is not available.
Refer to “Hill descent control function” F7-
44.
& BSD/RCTA warning in-
dicator (if equipped)
S03AE80
This warning indicator appears when the
BSD/RCTA is malfunctioning. In this case
the BSD/RCTA warning indicator will be
shown on the combination meter display
(color LCD). When this indicator appears,
have your vehicle inspected by your
SUBARU dealer as soon as possible.
& BSD/RCTA OFF indica-
tor (if equipped)
S03AE86
The indicator appears when the BSD/
RCTA OFF switch is pressed to deactivate
the BSD/RCTA, or when the BSD/RCTA is
suspended temporarily. In this case the
BSD/RCTA OFF indicator will be shown on
the combination meter display (color
LCD). For details, refer to “BSD/RCTA”
F7-62.
& RAB warning indicator
(if equipped)
S03AE91
This indicator illuminates if the Reverse
Automatic Braking (RAB) system malfunc-
tions. Refer to “Reverse Automatic Brak-
ing (RAB) system” F7-71.
& RAB OFF indicator (if
equipped)
S03AE92
This indicator illuminates when the Re-
verse Automatic Braking (RAB) system is
turned OFF, or when the Reverse Auto-
matic Braking (RAB) system is suspended
temporarily. Refer to “Reverse Automatic
Braking (RAB) system” F7-71.
& Icy road surface warn-
ing indicator (if
equipped)
S03AE82
When the outside temperature is 378F
(38C) or less, the icy road surface warning
will illuminate to inform the driver that the
road surface may be frozen.
NOTE
. The outside temperature indicator
shows the temperature around the
sensor. However, the temperature may
not be indicated correctly or the update
may be delayed in the following condi-
tions.
– While parking or driving at low
speeds
– When the outside temperature
changes suddenly (example: when
going in and out of an underground
parking area or when passing
through a tunnel)
– When starting the engine after
being parked for a certain period of
time
. The icy road surface warning screen
should be treated only as a guide. Be
sure to check the condition of the road
surface before driving.
. Once the icy road surface warning
screen appears, it will not disappear
unless the outside temperature has
increased to 418F (58C) or higher.
Instruments and controls/Warning and indicator
3-34
(173,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Combination meter display
(color LCD) (if equipped)
S03BN
WARNING
Always pay adequate attention to
safe driving when operating the
combination meter display (color
LCD) while the vehicle is in motion.
When operation of the combination
meter display (color LCD) interferes
with your ability to concentrate on
driving, stop the vehicle before
performing operations on the
screen. Also, do not concentrate on
the display while driving. Doing so
may cause you to look away from the
road and could result in an accident.
Various information will be shown on the
combination meter display (color LCD).
Also, a warning message will appear on
the display if a malfunction is detected. In
addition, several settings for the displayed
content can be performed.
Combination meter display (color LCD)
1) ECO gauge (Refer to “ECO gauge” F3-
10.)
2) Warning screen (Refer to “Warning
screen” F3-37.)/Basic screen (Refer to
“Basic screens” F3-38.)
3) EyeSight screen
4) Cruise control information display
5) Telltale screen (Refer to “Telltale screen”
F3-37.)
6) Select lever/gear position indicator (Re-
fer to “Select lever/gear position indicator
(CVT models)” F3-30.)
7) X-MODE indicator (if equipped) (Refer to
“X-MODE indicator” F3-33.)/SI-DRIVE
indicator (if equipped) (Refer to “SI-
DRIVE” F7-32.)
8) Odometer (Refer to “Odometer” F3-9.)/
Double trip meter (Refer to “Double trip
meter” F3-9.)
9) Fuel gauge (Refer to “Fuel gauge” F3-
10.)
A: Deactivating the EyeSight system or
models without the EyeSight system
B: Activating the EyeSight system
– CONTINUED –
Instruments and controls/Combination meter display (color LCD)
3-35
3
(174,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& Basic operation
S03BN01
Control switch
1)
(Up)
2)
/SET (enter)
3)
(Down)
By operating “
” or “ ” of the control
switch, the screens and selection items
can be switched. When the “
/SET”
switch is pulled toward you, the item can
be selected and set.
If there are some useful messages, such
as vehicle information, warning informa-
tion, etc., they will interrupt the current
screen, and appear on the display accom-
panied by a beep. If such a screen is
displayed, take proper action according to
the message shown on the screen.
The warning screen will return to the
original screen after a few seconds. While
the “
” information reminder is shown on
the display, it may be possible to display
the warning screen again. To recall the
message marked with “
” on the display,
pull the “
/SET” switch on the steering
wheel toward you.
NOTE
When the multi-function display (color
LCD) is set to the setting screen, the
combination meter display (color LCD)
cannot be controlled pulling on the
“
”, “ ” and “ /SET” on the control
switch.
& Welcome screen (opening
animation) and Good-bye
screen (ending animation)
S03BN08
When the driver’s door is opened and
closed after unlocking the door, the wel-
come screen (opening animation) will
appear on the combination meter display
(color LCD) for approximately 20 seconds.
When the ignition switch is turned to the
“LOCK”/“OFF” position, the combination
meter display (color LCD) gradually turns
off with showing Good-bye screen (ending
animation).
NOTE
. The welcome screen and the good-
bye screen may differ in the actual
words and appearance.
. Once the welcome screen appears, it
takes a certain period of time to display
it again.
. If the ignition switch is operated
after unlocking the driver’s door, the
welcome screen will not appear even
when the driver’s door is opened and
closed.
. The welcome screen will disappear
when you lock the driver’s door by
using the remote keyless entry system
(all models) or the keyless access
function (if equipped) while the wel-
come screen is displayed.
. The welcome screen including the
multi-function display (color LCD) (if
equipped) and the audio/navigation
unit can be set to on or off. For details,
refer to “Welcome Screen” F3-41.
Instruments and controls/Combination meter display (color LCD)
3-36
(175,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& Warning screen
S03BN05
Example of warning
If there is a warning message or a
maintenance notification, it will appear on
this screen. Take the appropriate actions
based on the messages indicated.
& Telltale screen
S03BN09
1) Telltale screen
When the corresponding situation occurs,
the following telltales will be displayed on
the telltale screen.
NOTE
When there is warning information to
display, it will be displayed in five
warning indicators, starting on the left
in ascending order of severity. If there
are six or more warning information
displayed, pull the “
/SET” switch and
check the item.
Mark Name Page
Door open warning light 3-22
LED headlight warning
light (models with LED
headlights)
3-32
High beam assist indi-
cator light (if equipped)
3-31
Steering Responsive
Headlight warning light
(if equipped)
3-32
Engine low oil level
warning light
3-18
RAB warning indicator
(if equipped)
3-34
RAB OFF indicator (if
equipped)
3-34
BSD/RCTA warning in-
dicator (if equipped)
3-34
BSD/RCTA OFF indi-
cator (if equipped)
3-34
Automatic headlight
beam leveler warning
light (models with LED
headlights)
3-32
– CONTINUED –
Instruments and controls/Combination meter display (color LCD)
3-37
3
(176,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Mark Name Page
Auto Start Stop warning
light/Auto Start Stop
OFF light (yellow) (if
equipped)
3-32
Auto Start Stop No Ac-
tivity Detected indicator
light (if equipped)
3-33
Auto Start Stop indica-
tor light (green) (if
equipped)
3-33
Windshield washer fluid
warning light
3-18
Hill descent control in-
dicator (if equipped)
3-34
Icy road surface warn-
ing indicator (if
equipped)
3-34
Engine hood open
warning light (if
equipped)
3-16
& Basic screens
S03BN06
By operating the “ ” or “ ” switch on the
steering wheel, you can change the screen
that is always displayed.
Average fuel consumption screen:
: Average fuel consumption
: Driving range on remaining fuel
This screen displays the average rate of
fuel consumption since the trip meter was
last reset.
NOTE
The driving range on remaining fuel is
only a guide. The indicated value may
differ from the actual driving range on
remaining fuel, so you must immedi-
ately fill the tank when the low fuel
warning light illuminates.
Current fuel consumption screen:
: Current fuel consumption
: Driving range on remaining fuel
This screen displays the rate of fuel
consumption at the present moment.
NOTE
The driving range on remaining fuel is
only a guide. The indicated value may
differ from the actual driving range on
remaining fuel, so you must immedi-
ately fill the tank when the low fuel
warning light illuminates.
Instruments and controls/Combination meter display (color LCD)
3-38
(177,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Driving information screen:
: Journey time
: Journey distance
This screen displays the journey time (the
time that has elapsed since the ignition
switch was turned to the “ON” position)
and journey distance (the distance that
has been driven since the ignition switch
was turned to the “ON” position).
Digital speed screen:
1) Speed limit indicator (if equipped)
2) Vehicle speed
This screen displays the current vehicle
speed.
Auto Start Stop screen (if equipped):
: The total amount of time that the engine
was stopped by means of the Auto Start
Stop system
: The total amount of fuel saved due to the
engine being stopped by the Auto Start
Stop system
The indicated values are calculated from
the most recent reset of the currently
displayed trip meter to the current time.
The indication ranges are as follows.
. Total amount of time: from 00’00@ to
9999h59’59@
. Total amount of fuel saved: from 0 ml to
9999.999 L
NOTE
. When the trip meter is reset, the
corresponding accumulated time and
the amount of fuel saving are also reset.
– CONTINUED –
Instruments and controls/Combination meter display (color LCD)
3-39
3
(178,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
. The time spent with the engine
stopped by means of the Auto Start
Stop system is also added to the
journey time.
SI-DRIVE mode screen (if equipped):
This screen indicates the current SI-
DRIVE mode with its throttle angle.
TPMS screen (U.S.-spec. models):
This screen displays each tire pressure.
When a tire is deflated, the deflated tire
and the tire pressure will be displayed on
the screen in yellow.
NOTE
. The tire pressure values are dis-
played several minutes after driving.
. You can set the tire pressure units.
For details about setting the units, refer
to “Tire Pressure Units” F3-41.
. Once the tire pressure monitoring
system detects the low tire pressure,
the tire pressure values will display in
yellow until the system detects the
normal tire pressure.
. Immediately adjust the tire pressure
when the warning light illuminates.
When the tire pressure monitoring
system detects the adjusted tire pres-
sure, the warning light will turn off and
the tire pressure values will turn to
white.
. For information about the specified
value of the air pressure, refer to
“Tires” F12-8.
Menu screen entering screen:
While this screen is selected, pull and hold
the “
/SET” switch to enter the menu
screen.
Instruments and controls/Combination meter display (color LCD)
3-40
(179,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& Menu screens
S03BN07
Pull and hold the “ /SET” switch to enter
the menu screens when all of the following
conditions are satisfied.
. The menu screen entering screen is
selected.
. The “
” information reminder is off.
NOTE
. While driving, the setting items
available on the combination meter
display (color LCD) are limited.
. For function settings and adjust-
ments on the combination meter dis-
play, refer to “Function settings and
adjustments on the combination meter
display (color LCD)” F25.
By operating the “
” or “ ” switch on the
steering wheel, you can select the menu.
Pull the “
/SET” switch to enter the
selected menu.
NOTE
If you enter the “Go Back” menu, the
system will return to the previous
screen.
! Screen Settings
S03BN0701
After entering the “Screen Settings” menu,
select one of the following menus.
! Welcome Screen
S03BN070101
The welcome screen can be activated or
deactivated.
! Good-bye Screen
S03BN070106
The good-bye screen can be activated or
deactivated.
! Gauge Initial Movement
S03BN070102
The movement of the meter needles and
gauge needles that occurs when the
ignition switch is turned to the “ON”
position can be activated or deactivated.
! Units
S03BN070108
Changes the units displayed in the combi-
nation meter display (color LCD), the multi-
function display (black and white) and the
multi-function display (color LCD).
! Tire Pressure Units (if equipped)
S03BN070109
Changes the units displayed in the Tire
Pressure Monitoring system.
! Languages
S03BN070103
Changes the language displayed in the
combination meter display (color LCD)
and the multi-function display (color LCD).
! Warning Volume (if equipped)
S03BN0713
Sets the EyeSight warning volume, the
BSD/RCTA warning volume and the Re-
verse Automatic Braking (RAB) warning
volume.
! Rear Seat Reminder (models with
combination meter display (color
LCD))
S03BN0715
The Rear Seat Reminder can be activated
or deactivated.
! EyeSight (models with EyeSight
system)
S03BN0702
NOTE
For models with the EyeSight system,
refer to the Owner’s Manual supple-
ment for the EyeSight system.
! RAB (if equipped)
S03BN0712
The Sonar Audible Alarm can be set to on
or off.
NOTE
For models with Reverse Automatic
Braking (RAB) system, refer to “Re-
verse Automatic Braking (RAB) sys-
tem” F7-71.
! Sonar Audible Alarm
S03BN071204
When the Reverse Automatic Braking
(RAB) system is in operation, the warning
sound to notify that an obstacle is detected
in the rear can be activated or deactivated.
– CONTINUED –
Instruments and controls/Combination meter display (color LCD)
3-41
3
(180,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! Vehicle Setting
S03BN0708
After entering the “Vehicle Setting” menu,
select one of the following menus.
! Keyless Entry System
S03BN070801
Sets the settings used when the keyless
access function was operated.
. Audible Signal (if equipped)
Sets the electronic chirp that sounds when
the door is locked or unlocked.
. Hazard Warning Flasher
Sets the operation of the hazard warning
flasher that blinks when the door is locked
or unlocked.
. Driver Door Unlock (if equipped)
Select only the driver’s door to unlock or all
doors to unlock simultaneously when the
driver’s door is unlocked.
. Rear Gate/Trunk Unlock (if equipped)
Select only the rear gate to unlock or all
doors to unlock simultaneously when
accessing from the cargo area.
! Defogger
S03BN070802
Sets and customizes the operation of the
defogger.
! Interior Light
S03BN070803
Sets and customizes the interior light off
delay timer.
! Auto Door Lock and Unlock
S03BN070808
Setting conditions for Auto Door Lock and
Unlock
. Auto Door Lock:
Set the condition of the following items to
lock the door automatically.
– Vehicle Speed: When the vehicle
speed reaches more than 12 mph (20
km/h).
– Shift Into or Out of PARK: When the
select lever is shifted into a position
other than the “P” position (CVT
models).
– Off: When the function is set to OFF.
. Auto Door Unlock:
Set the conditions of the following items to
unlock the door automatically.
– Shift Into or Out of PARK: When the
select lever is shifted into the “P”
position (CVT models).
– Ignition OFF: When the ignition
switch is turned to OFF.
– Driver Door Open: When the dri-
ver’s door is open.
– Off: When the function is set to OFF.
! Auto Light Sensor (if equipped)
S03BN070804
Sets and customizes the sensitivity of the
auto light sensor.
! Welcome Lighting (if equipped)
S03BN070806
Sets the leaving time and approaching
time.
. Approaching time set
Sets the illumination time of the headlights
that illuminate when you approach the
vehicle.
. Leaving time set
Sets the time until the headlights turn off
when you have moved away from the
vehicle.
! One-touch lane changer
S03BN070807
Sets the one-touch lane changer on/off.
! Default Settings
S03BN0704
Select “Yes” to use the menu screen to
restore customized settings to the factory
default settings. Select “No” to return to the
previous screen without restoring to the
factory default settings.
Instruments and controls/Combination meter display (color LCD)
3-42
(181,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Multi-function display (black
and white)
S03BO
NOTE
For models with multi-function display
(color LCD), refer to “Multi-function
display (color LCD)” F3-49.
Multi-function display (black and white)
type A
1) Clock
2) Auto Start Stop system (if equipped)
3) Outside temperature indicator
4) Driving information display
5) Climate control screen
Multi-function display (black and white)
type B
1) Outside temperature indicator
2) X-MODE indicator (if equipped)
3) Driving information display
4) Clock
With the ignition switch in the “ACC”
position, the clock appears on the display.
With the ignition switch in the “ON” posi-
tion, the outside temperature indicator,
driving information display and clock all
appear on the display.
NOTE
The indicated values vary in accor-
dance with changes in the vehicle’s
running conditions. Also, the indicated
values may differ slightly from the
actual values and should thus be
treated only as a guide.
& Driving information display
S03BO09
NOTE
You can set the units for both the multi-
function display (black and white) and
the combination meter at the same
time. For details about setting the
language and units, refer to “Type A
combination meter” F3-11 or “Menu
screens” F3-41.
! How to change the information dis-
play
S03BO0910
1) INFO button
Pressing the INFO button on the steering
wheel switches the display in the following
sequence.
– CONTINUED –
Instruments and controls/Multi-function display (black and white)
3-43
3
(182,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
*1: Models without combination meter display
(color LCD)
*2: If equipped
! Driving range on remaining fuel
S03BO0903
1) When setting the displayed unit as MPH
2) When setting the displayed unit as km/h
The driving range indicates the distance
that can be driven taking into account the
amount of fuel remaining in the tank and
the average rate of fuel consumption.
1) When setting the displayed unit as MPH
2) When setting the displayed unit as km/h
If the driving range is shown as “
”, there
is only a tiny amount of fuel left in the tank.
NOTE
The driving range on remaining fuel is
only a guide. The indicated value may
differ from the actual driving range on
remaining fuel, so you must immedi-
ately fill the tank when the low fuel
warning light illuminates.
Instruments and controls/Multi-function display (black and white)
3-44
(183,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! Average fuel consumption
S03BO0902
1) Displays the driving range per gallon of
fuel
2) Displays the driving range per liter of fuel
3) Displays the fuel consumption per 100
km
This display shows the average rate of fuel
consumption since the trip meter was last
reset.
1) TRIP RESET switch
Press the TRIP RESET switch to switch
between the displays for the average fuel
consumption that corresponds to the A trip
meter mileage and the average fuel con-
sumption that corresponds to the B trip
meter mileage.
When the trip meter displays is reset, the
corresponding average fuel consumption
value is also reset.
NOTE
. When the trip meter display is reset,
the average fuel consumption corre-
sponding to that trip meter display is
not shown until the vehicle has subse-
quently covered a distance of 1 mile (or
1 km).
. The units for measuring average fuel
consumption cannot be changed.
! Current fuel consumption
S03BO0901
1) Displays the driving range per gallon of
fuel
2) Displays the driving range per liter of fuel
3) Displays the fuel consumption per 100
km
This indication shows the rate of fuel
consumption at the present moment.
– CONTINUED –
Instruments and controls/Multi-function display (black and white)
3-45
3
(184,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! Journey time (models without com-
bination meter display (color LCD))
S03BO0904
The journey time shows the time that has
elapsed since the ignition switch was
turned to the “ON” position.
The journey time indication flashes each
time a complete hour has elapsed. If the
display is giving a reading other than the
journey time, the display switches to the
journey time, flashes for 5 seconds, and
returns to its original reading each time a
complete hour has elapsed.
NOTE
The journey time is reset when the
ignition switch is turned to the “ACC”
or “LOCK”/“OFF” position.
! Average vehicle speed
S03BO0905
1) When units in miles is selected
2) When units in km is selected
This display shows the average vehicle
speed since the trip meter was last reset.
Pressing the TRIP RESET switch toggles
the display between the average vehicle
speed corresponding to the A trip meter
display and the average vehicle speed
corresponding to the B trip meter display.
When either of the trip meter displays is
reset, the corresponding average vehicle
speed value is also reset.
NOTE
When either trip meter display is reset,
the average vehicle speed correspond-
ing to that trip meter display is not
shown until the vehicle has subse-
quently covered a distance of 1 mile
(or 1 km).
! Auto Start Stop time (if equipped)
S03BO0907
1) Total time in conjunction with the trip
meter
2) Total time in conjunction with the ignition
switch
Instruments and controls/Multi-function display (black and white)
3-46
(185,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
This display shows the total time that the
engine was stopped by the Auto Start Stop
system in the following ways.
Total time in conjunction with the trip
meter: Displays the total time that the
engine was stopped by the Auto Start Stop
system, from the last time the currently
displayed trip meter was reset until the
current time. By pressing the TRIP RESET
switch, you can toggle the display between
the time the engine was stopped for trip A
and the time the engine was stopped for
trip B.
NOTE
When the trip meter mileage is reset,
the total time in conjunction with the
trip meter is not shown until the vehicle
has subsequently covered a distance
of 1 mile (or 1 km).
Total time in conjunction with the igni-
tion switch: Displays the total time that
the engine was stopped by the Auto Start
Stop system, from the time when the
ignition switch was turned to the “ON”
position to the current time.
! How to switch the display
S03BO090701
Perform the following operation to toggle
the display between the total time in
conjunction with the trip meter and the
total time in conjunction with the ignition
switch.
1. Press and hold the “+” button located
on the side of the information display. The
stopped time will then flash.
2. Within 5 seconds after the stopped
time starts flashing, press and hold the “−”
button located on the side of the informa-
tion display. The display will then change
and after flashing for 3 seconds, the
stopped time selected will be displayed.
3. Each time the “−” button is pressed and
held during the 3 seconds that the display
is flashing, the display will change and
flash for 3 seconds. If the “−” button is not
pressed and held during the 3-second
period that the display is flashing, the
stopped time selected will be displayed.
! Turn off display of driving informa-
tion display
S03BO0906
Select the blank space in the menu to exit
the driving information display selection.
NOTE
. The average fuel consumption and
average vehicle speed are calculated
even while the driving information dis-
play has been turned off.
. Even if you turn off the driving
information display, the display will
automatically turn on when the battery
voltage is disconnected and then re-
connected for battery replacement or
fuse replacement.
– CONTINUED –
Instruments and controls/Multi-function display (black and white)
3-47
3
(186,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& Outside temperature indica-
tor
S03BO01
1) U.S.-spec. models
2) Except U.S.-spec. models
NOTE
. The outside temperature indicator
shows the temperature around the
sensor. However, the temperature may
not be indicated correctly or the update
may be delayed in the following condi-
tions.
– While parking or driving at low
speeds
– When the outside temperature
changes suddenly (example: when
going in and out of an underground
parking area or when passing
through a tunnel)
– When starting the engine after
being parked for a certain period of
time
. The temperature unit cannot be
changed.
! Road surface freeze warning indi-
cation
S03BO0101
1) U.S.-spec. models
2) Except U.S.-spec. models
When the outside temperature drops to a
certain temperature or lower, the tempera-
ture indication flashes for 5 seconds to
show that the road surface may be frozen.
If the display is already indicating that the
outside temperature is low when the
ignition switch is turned to the “ON”
position, the indication does not flash.
NOTE
The outside temperature indication
may differ from the actual outside
temperature. The road surface freeze
warning indication should be treated
only as a guide. Be sure to check the
condition of the road surface before
driving.
& X-MODE indicator (if
equipped)
S03BO12
This indicator will be shown while the X-
MODE is activated. It will turn off when the
X-MODE is deactivated.
& Clock
S03BO10
For details about clock setting, refer to
“Clock” F3-66.
Instruments and controls/Multi-function display (black and white)
3-48
(187,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& Climate control screen
S03BO13
The climate control status is displayed on
the multi-function display (black and white)
type A.
Climate control screen
1) Set temperature indicator
2) FULL AUTO indicator
3) AUTO indicator
4) Air conditioner ON indicator
5) Airflow mode indicator
6) Air inlet selection indicator
7) Fan speed indicator
When operating the climate control sys-
tem, the basic screen switches to the
climate control screen. For details about
climate control operation, refer to “Climate
control panel” F4-2.
Multi-function display (color
LCD) (if equipped)
S03BP
NOTE
For models with multi-function display
(black and white), refer to “Multi-func-
tion display (black and white)” F3-43.
WARNING
Always pay adequate attention to
safe driving when operating the
multi-function display (color LCD)
while the vehicle is in motion. When
operation of the multi-function dis-
play (color LCD) is disturbing your
awareness and ability to concen-
trate on driving, stop the vehicle in
a safe place before performing op-
erations on the screen. Also, do not
concentrate on the display while
driving. Doing so may cause you to
look away from the road and could
result in an accident.
& Features
S03BP25
The multi-function display (color LCD) has
the following functions.
Description Page
Displays useful messages, such
as notification, etc.
3-51
Displays basic screens (e.g. fuel
consumption screen, etc.)
3-51
Sets and adjusts maintenance
notification
3-64
Also, the multi-function display (color LCD)
can also be used to set and initialize the
multi-function display (color LCD) itself.
NOTE
. When the vehicle is in motion,
certain functions and selections may
not be available.
. You can set the language and units
for both the multi-function display
(color LCD) and the combination meter
at the same time. For details about
setting the language and units, refer to
“Menu screens” F3-41.
. The images displayed in this Own-
er’s Manual are sample images. The
actual image may vary depending on
the market and vehicle specifications.
– CONTINUED –
Instruments and controls/Multi-function display (color LCD)
3-49
3
(188,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& Welcome screen
S03BP07
When the driver’s door is opened and
closed, the welcome screen will appear for
a short time.
NOTE
. The welcome screen will disappear
when the ignition switch is turned to the
“ON” position while the welcome
screen is displayed.
. The welcome screen can be set to on
or off. For details, refer to “Screen
Settings” F3-41.
. For a certain period of time after the
welcome screen has once appeared, it
may not appear again even when the
driver’s door is opened and closed
again. This does not indicate a mal-
function.
& Self-check screen
S03BP09
NOTE
When the setting is “On”, the self-
check screen appears. For details
about this setting, refer to “On/Off
setting” F3-64.
When the ignition switch is turned to the
“ON” position, the vehicle self-check will
be performed. The screens corresponding
to the following items will appear one after
another for several seconds each.
1) Engine oil: Checks the interval of engine
oil replacement.
2) Oil filter: Checks the interval of oil filter
replacement.
3) Tires: Checks the interval of tire rotation.
4) Inspection and maintenance: Checks the
interval of inspection and maintenance.
When the checks are performed, the color
of the icon corresponding to the checked
item will change.
If there is a notification, the message will
be displayed. Take the appropriate actions
based on the message indicated.
After the self-check is completed, today’s
date, the stored birthday or the stored
anniversary is displayed.
NOTE
. After performing the maintenance,
change the setting of the correspond-
ing maintenance item. For details, refer
to “Maintenance settings” F3-64.
. The maintenance notification screen
will be displayed under either of the
following conditions.
– The period of time remaining until
the registered notification date is 15
days or less.
– The total driving distance remain-
ing until the registered notification
distance is approximately 311 miles
(500 km) or less.
. The maintenance notification screen
will be displayed until either of the
following conditions is satisfied.
– The period of time passed after
the registered notification date is 15
days or more.
– The total distance driven after the
registered notification distance is
approximately 311 miles (500 km) or
more.
Instruments and controls/Multi-function display (color LCD)
3-50
(189,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& Interruption screen
S03BP19
Example
Useful messages, such as reminder in-
formation, weather information (if
equipped) and traffic information (if
equipped) may interrupt the current screen
and appear on the display accompanied
by a beep. Take proper action according to
the message.
The interruption screen will return to the
original screen after a few seconds. Also,
you can press the INFO button to skip the
interruption screen.
& Basic operation
S03BP06
Control switch
1) INFO button
2)
3) /SET
4)
Press the INFO button on the steering
wheel to switch the item displayed on the
basic screen. You can operate the items
on the setting screen by using the “
”,
“
” and “ /SET” switches.
& Basic screens
S03BP10
1) Clock
2) Climate control*
3) Outside temperature
4) Information screen
*: This is not displayed on the multi-function
display (color LCD) when the ignition switch
– CONTINUED –
Instruments and controls/Multi-function display (color LCD)
3-51
3
(190,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
is in the “ACC” position.
While the ignition switch is in the “ACC” or
“ON” position, the basic screen will be
displayed.
! Outside temperature indicator
S03BP1016
The outside temperature is displayed on
the multi-function display (color LCD).
NOTE
. The outside temperature indicator
shows the temperature around the
sensor. However, the temperature may
not be indicated correctly or the update
may be delayed in the following condi-
tions.
– While parking or driving at low
speeds
– When the outside temperature
changes suddenly (example: when
going in and out of an underground
parking area or when passing
through a tunnel)
– When starting the engine after
being parked for a certain period of
time
. The temperature unit cannot be
changed.
! Climate control screen
S03BP1017
The climate control status is displayed on
the multi-function display (color LCD).
Climate control screen
1) Set temperature indicator (left-hand side)
2) FULL AUTO indicator
3) AUTO indicator
4) Airflow mode indicator
5) Set temperature indicator (right-hand
side)*
1
6) Air inlet selection indicator
7) SYNC indicator*
1
8) Fan speed indicator
9) Air conditioner ON indicator
*1: Models with the SYNC function only
When operating the climate control sys-
tem, the basic screen switches to the
climate control screen. For details about
climate control operation, refer to “Climate
control panel” F4-2.
! Clock
S03BP1018
The clock can be displayed in either 12-
hour display or 24-hour display. For details
about the setting, refer to “Clock” F3-66.
Instruments and controls/Multi-function display (color LCD)
3-52
(191,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! Information screen
S03BP1019
Press the INFO button on the steering wheel to switch the item displayed on the information screen.
Content Description Page
Electric components operating status screen
Displays the operating status of the electric components and equipment. 3-54
Prevention safety screen Displays the status of your vehicle. 3-54
EyeSight screen*
1
Displays the operating status of EyeSight. 3-55
Favorite screen Displays up to 3 optional items. 3-55
Weather information screen*
2
Displays weather information. 3-56
Traffic information*
2
/Navigation*
3
screen Displays information linked with the navigation system. 3-56
Audio screen Displays audio system information. 3-57
Fuel consumption screen Displays fuel consumption information. 3-57
Clock/date screen Displays the clock. 3-57
Guidance screen Moves to the setting screen.
3-58
*1: Models with EyeSight system
*2: Models with SiriusXM Satellite Radio
*3: Models with navigation system
– CONTINUED –
Instruments and controls/Multi-function display (color LCD)
3-53
3
(192,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! Electric components operation
screen
S03BP101901
1) Lane Departure Warning indicator*
1
2) Pre-Collision Braking System indicator*
1
3) Stop lights
4) Reverse Automatic Braking (RAB)*
1
5) BSD/RCTA*
1
6) Headlights*
2
7) Front fog lights*
2
8) Turn signals
9) Auto on/off headlights*
1
*1: If equipped
*2: The daytime running lights are not dis-
played.
This screen displays the electric compo-
nents operation status of the vehicle.
NOTE
. Indicators do not display for func-
tions that are not equipped to the
vehicle.
. The indicators of functions that are
not operating are displayed in gray.
. For models with auto on/off head-
lights; If the multi-function display
(color LCD) unit, battery, or fuse is
removed, the Auto on/off headlights
indicator turns off on the multi-function
display (color LCD). After reinstalling
the removed multi-function display
(color LCD) unit, battery, or fuse to the
vehicle, the Auto on/off headlights
indicator will appear once more if the
light control switch is turned to the
“AUTO” position.
. The exterior lights indicators on the
screen do not notify the driver when the
bulbs burn out. The indicators on the
screen still illuminate.
! Prevention safety screen
S03BP101902
1) Telltale screen
2) Steering angle
3) Vehicle posture
4) Running condition
This screen displays the driving status of
the vehicle and the operation status func-
tions. For functions that are operating, the
indicator will illuminate or flash.
NOTE
. The vehicle posture indication may
differ from the actual vehicle posture.
. When X-MODE has turned on, the
screen of the multi-function display is
switched to the prevention safety
screen.
Instruments and controls/Multi-function display (color LCD)
3-54
(193,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! EyeSight screen (models with
EyeSight system)
S03BP101903
1) Lead vehicle indicator
2) Your own vehicle indicator
3) Stop lights
4) Road line indicator
5) Lane indicator
This screen displays the status of the
EyeSight system. The lead vehicle indica-
tor moves forward and backward depend-
ing on the distance with the vehicle in front.
For details, refer to the Owner’s Manual
supplement for the EyeSight system.
! Favorite screen
S03BP101904
Favorite screen (display example)
This screen displays up to three optional
pieces of information that can be selected
from the following items.
Item Details
The engine coolant temperature is
displayed.
The engine oil temperature is
displayed.
The average vehicle speed is
displayed.
The accelerator opening ratio is
displayed.
The vehicle posture is displayed.
The current rate of fuel consump-
tion is displayed.
The direction of the vehicle is
displayed.*
1
The weather information is dis-
played.*
2
– CONTINUED –
Instruments and controls/Multi-function display (color LCD)
3-55
3
(194,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Item Details
The posted speed limit of the road
you are currently driving on is
displayed.*
1
The calendar is displayed.
Nothing is displayed.
*1: If equipped
*2: Models with SiriusXM Satellite Radio
NOTE
Some displayed items may be not
displayed depending on the model
and specifications.
The items shown in the favorite screen can
be changed. For details, refer to “Favorite
setting” F3-62.
! Weather information screen (if
equipped)
S03BP101905
1) Weather information for the destination*
2) Weather information for the current loca-
tion
*: Only when a destination is set in the
navigation system
The weather information is displayed on
the screen.
NOTE
. When all of the following conditions
are satisfied, weather information is
displayed.
– The vehicle is equipped with an
audio and navigation system for
SiriusXM satellite radio.
– You have a current SiriusXM
satellite radio subscription.
. The weather forecast for the set
destination remains displayed until a
new destination is set or until you reach
the destination.
. Depending on the reception timing
of XM, the display of weather informa-
tion may be delayed.
! Navigation screen (models with
navigation system)
S03BP101906
The navigation system information to the
destination is displayed on the screen.
NOTE
When a destination is not set in the
navigation system, the compass orien-
tation, name, route sign and speed limit
of the road the vehicle is traveling on
remain displayed on the screen.
Instruments and controls/Multi-function display (color LCD)
3-56
(195,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! Audio screen
S03BP101907
The screen of the currently selected audio
source is displayed.
For details about how to use the audio set,
refer to the separate navigation/audio
Owner’s Manual.
! Fuel consumption screen
S03BP101908
1) Driving range on remaining fuel
2) Average fuel consumption corresponding
to the driving distance of each trip meter
3) Current fuel consumption
The fuel consumption information is dis-
played on the screen.
NOTE
The driving range on remaining fuel is
only a guide. The indicated value may
differ from the actual driving range on
remaining fuel, so you must immedi-
ately fill the tank when the low fuel
warning light illuminates.
! Clock/date screen
S03BP101909
The time and date are displayed.
You can adjust the time and date. For
details, refer to “Clock” F3-66.
– CONTINUED –
Instruments and controls/Multi-function display (color LCD)
3-57
3
(196,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! Guidance screen
S03BP101910
When the INFO button on the steering
wheel is pressed and held on this screen,
the setting screen can be displayed.
For details, refer to “Setting screen” F3-
58.
NOTE
When the combination meter display
(color LCD) is displaying the menu
screen entering screen, the system will
not move to the setting screen even if
the INFO button is pressed and held.
& Setting screen
S03BP28
1. Press and hold the INFO button on the
guidance screen. The top menu is dis-
played.
2. Operate the “
” or “ ” switch to
select the preferred menu from the top
menu.
3. Pull the “
/SET” switch to enter the
selected menu.
4. Operate the “
” or “ ” switch to
select the preferred menu from the 2nd
menu.
5. Pull the “
/SET” switch to enter the
selected menu.
Instruments and controls/Multi-function display (color LCD)
3-58
(197,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
The menu lists are as follows.
Items that can be set when stopped:
Top menu 2nd menu Description Page
Date
Birthday Set a birthday. 3-61
Anniversary Set an anniversary day. 3-61
Go Back Return to the 1st menu. —
Display/Beep
Screen Off Turn the screen on or off. Yes or No 3-61
Favorite Set and customize the triple meter. 3-62
Bypass Screen Set the bypass screen for each item. On or Off 3-62
Beep Adjust the beep sound volume. High, Low or Off 3-62
Go Back Return to the 1st menu. —
Camera Set-
tings
Brightness Set and adjust the brightness of a display. 3-63
Contrast Set and adjust the contrast of a display. 3-63
Camera Shift Link Set the camera shift link. On or Off 3-63
Go Back Return to the 1st menu. —
Maintenance
Engine Oil Set and adjust the oil maintenance notification date. 3-64
Oil Filter Set and adjust the oil filter maintenance notification date. 3-64
Tires Set and adjust the tire maintenance notification date. 3-64
Maintenance Schedule Set and adjust the vehicle maintenance notification date. 3-64
ON/OFF
Turn on or off the self-check screen that is
activated when the ignition switch is turned to the
“ON” position.
On or Off 3-64
Clear All Settings Clear all settings for maintenance items. Yes or No 3-65
Go Back Return to the 1st menu.
—
– CONTINUED –
Instruments and controls/Multi-function display (color LCD)
3-59
3
(198,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Top menu 2nd menu Description Page
Initialize — Reset all settings to the default settings. Yes or No 3-65
Go Back — Return to the setting screen.
—
Items that can be set while driving:
Menu Description Page
Screen Off Turn the screen on or off. 3-61
Go Back Return to the settings screen.
—
For safety reasons, we recommend stopping the vehicle in a safe location while setting.
Instruments and controls/Multi-function display (color LCD)
3-60
(199,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! Date and time settings
S03BP2801
You can set the date, time and 12h or 24h
format settings.
! Current date and time setting
S03BP280101
For details about clock setting, refer to
“Clock” F3-66.
! Birthday setting
S03BP280102
If a birthday or anniversary is approaching,
a message will be displayed when the
ignition switch is turned to the “ON”
position. This function can be set to on or
off. For details, refer to “Bypass screen
setting” F3-62.
1. Select “Birthday” from the 2nd menu in
the setting screen. Refer to “Setting
screen” F3-58.
2. Select from the list the number that you
want to register.
3. Enter the date and the text by using the
control switches.
4. Select “Set” to exit settings. Select “Go
Back” to return to the previous screen
without applying the setting changes.
NOTE
You can store a maximum of 5 birth-
days.
! Anniversary setting
S03BP280103
1. The procedure for setting an anniver-
sary is the same as “Birthday setting” F3-
61, except that in step 1 “Anniversary” is
selected.
NOTE
You can store a maximum of 5 anniver-
saries.
! Display/Beep settings
S03BP2805
You can set the display settings and
volume settings.
! Screen OFF setting
S03BP280501
1. Select “Screen Off” from the 2nd menu
in setting screen. Refer to “Setting screen”
F3-58.
2. Select “Yes” to turn off the screen.
Select “No” to return to the previous
screen.
Restoring the screen
When the INFO button is operated after
– CONTINUED –
Instruments and controls/Multi-function display (color LCD)
3-61
3
(200,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
the ignition switch is turned to the “ON” or
“ACC” position, the screen will be restored.
The screen will be restored with the basic
screen that was displayed when the
screen was turned off.
NOTE
While the screen is off, the screen
switches to the climate control screen
only when the climate control system is
operated.
! Favorite setting
S03BP280502
1. Select the “Favorite” from the 2nd
menu in setting screen. Refer to “Setting
screen” F3-58.
2. Set the desired items by using the
control switches. For details about items,
refer to “Favorite screen” F3-55.
3. Select “Set” to exit settings. Select “Go
Back” to return to the previous screen
without applying the setting changes.
NOTE
. You can display a maximum of the 3
items.
. The same item cannot be selected
for the left, center or right location.
. Weather information for 3 hours
later or 6 hours later can be displayed.
! Bypass screen setting
S03BP280503
1. Select “Bypass Screen” from the 2nd
menu in the setting screen. Refer to
“Setting screen” F3-58.
2. Select “On” or “Off” to turn the display
of items on or off by using the control
switches.
3. Select “Set” to exit settings. Select “Go
Back” to return to the previous screen
without applying the setting changes.
NOTE
Traffic information setting is only dis-
played for the audio unit with SiriusXM
satellite radio.
! Beep setting
S03BP280504
1. Select “Beep” from the 2nd menu in the
setting screen. Refer to “Setting screen”
F3-58.
2. Set the beep volume by using the
control switches.
3. Select “Set” to exit settings. Select “Go
Back” to return to the previous screen
Instruments and controls/Multi-function display (color LCD)
3-62
(201,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
without applying the setting changes.
! Camera Settings (if equipped)
S03BP2809
You can set the front camera display
settings.
! Brightness setting
S03BP280901
1. Select “Brightness” from the 2nd menu
in the setting screen. Refer to “Setting
screen” F3-58.
2. Select the brightness level by using the
control switches.
3. Press the “
/SET” button to confirm
the setting.
! Contrast setting
S03BP280902
1. Select “Contrast” from the 2nd menu in
the setting screen. Refer to “Setting
screen” F3-58.
2. Select the contrast level by using the
control switches.
3. Press the “
/SET” button to confirm
the setting.
! Camera shift link setting
S03BP280903
1. Select “Camera Shift Link” from the
2nd menu in the setting screen. Refer to
“Setting screen” F3-58.
2. Select “On” or “Off” by using the control
switches.
3. Select “Set” to exit settings. Select “Go
Back” to return to the previous screen
without applying the setting changes.
– CONTINUED –
Instruments and controls/Multi-function display (color LCD)
3-63
3
(202,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! Maintenance settings
S03BP2803
You can set maintenance reminders.
! Engine oil setting
S03BP280301
1. Select “Engine Oil” from the 2nd menu
in the setting screen. Refer to “Setting
screen” F3-58.
2. Set the date and distance of the
reminder by using the control switches.
3. Select “Set” to exit settings. Select
“Update” to change the notification dis-
tance to the default value. Select “Go
Back” to return to the previous screen
without applying the setting changes.
NOTE
. The reminder will be displayed by
either date or distance in accordance
with the setting.
. Even when either “Day” or “Dis-
tance” are displayed as “_ _” a pop-up
screen will appear.
. The reminder will be displayed until
either of the following conditions is
satisfied.
– The period of time passed after
the registered notification date is 15
days or more.
– The total distance driven after the
registered notification distance is
approximately 311 miles (500 km) or
more.
! Oil filter setting
S03BP280302
The setting procedure is the same as
“Engine oil setting” F3-64, but select the
“Oil Filter” item in step 1.
! Tires setting
S03BP280303
The setting procedure is the same as
“Engine oil setting” F3-64, but select the
“Tires” item in step 1.
! Maintenance schedule setting
S03BP280304
The setting procedure is the same as
“Engine oil setting” F3-64, but select the
“Maintenance Schedule” item in step 1.
! On/Off setting
S03BP280305
1. Select “On/Off” from the 2nd menu on
the setting screen. Refer to “Setting
screen” F3-58.
2. Select “On” or “Off” to turn the opening
screen on or off by using the control
switches.
3. Select “Set” to exit settings. Select “Go
Back” to return to the previous screen
without applying the setting changes.
Instruments and controls/Multi-function display (color LCD)
3-64
(203,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! Clear setting
S03BP280306
1. Select “Clear All Settings” from the 2nd
menu on the setting screen. Refer to
“Setting screen” F3-58.
2. Select “Yes” or “No” by using the
control switches.
! Initialize
S03BP2804
You can initialize the items that have been
set to your preference.
1. Select “Initialize” from the 2nd menu on
the setting screen. Refer to “Setting
screen” F3-58.
2. Select “Yes” or “No” by using the
control switches.
& How to get the source code
using the open source
S03BP29
Free/Open Source Software Information
This product contains Free/Open Source
Software (FOSS).
The license information and/or the source
code of such FOSS can be found at the
following URL.
.
source/ivi/subaru/
Instruments and controls/Multi-function display (color LCD)
3-65
3
(204,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Clock
S03AF
For models with a SUBARU genuine
navigation and/or audio system, the clock
can be adjusted using either auto mode or
manual mode.
. Auto mode: automatic clock adjustment
. Manual mode: manual clock adjust-
ment
CAUTION
The clock in the multi-function dis-
play (color LCD) cannot be adjusted,
if the SUBARU genuine navigation
and/or audio system is removed.
& Setting the clock manually
S03AF03
! Multi-function display (black and
white)
S03AF0309
1. Turn the ignition switch to “ON”.
2. Press the button.
3. Select “Settings”.
4. Select “Vehicle”.
5. Select “Clock adjustment” and then
select “Manual”.
6. Press the “+” button or the “−” button
beside the clock.
! Setting 12-hour or 24-hour dis-
play
S03AF030901
The clock can be set to 12-hour or 24-hour
display. Perform the following procedure to
switch the display format.
1. Turn the ignition switch in the “LOCK”/
“OFF” position.
2. Press and hold the “−” button located
near the clock display for approximately 5
seconds. The clock display will then start
to flash.
3. While the clock display is flashing,
press and hold the “+” button for approxi-
mately 2 seconds. The clock format will
then change.
Instruments and controls/Clock
3-66
(205,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
4. The clock display will continue to flash
for approximately 3 seconds to indicate
that the clock display has been changed.
! Multi-function display (color LCD)
S03AF0310
1. Turn the ignition switch to “ON”.
2. Press the button.
3. Select “Settings”.
4. Select “Vehicle”.
5. Select “Time/Date” and then select
“Manual”.
6. Set the each items plus and minus.
7. Select
to complete the clock
setting.
Select “Back” to return to the previous
screen without saving settings.
NOTE
. Adjust the time, then select 12h
display or 24h display from the format.
. The Birthday/Anniversary and main-
tenance reminder system function are
based on the time and date on the
multifunction display (color LCD).
& Setting the clock automati-
cally
S03AF02
1. Turn the ignition switch to “ON”.
2. Press the button.
3. Select “Settings”.
4. Select “Vehicle”.
5. Select “Time/Date”.
6. Select “Auto”.
– CONTINUED –
Instruments and controls/Clock
3-67
3
(206,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! Models with navigation system
S03AF0201
The clock will be set automatically where a
GPS signal is available.
! Models without navigation system
S03AF0202
The clock will be set and adjusted auto-
matically when a smartphone is connected
via Bluetooth
®
for transferring phonebook
data.
1. Register the smartphone to the audio
system. For details, refer to “Bluetooth
SETTINGS” in the supplemental Owner’s
Manual for the audio/navigation system.
2. Transfer phonebook data to the sys-
tem. For details, refer to “Bluetooth SET-
TINGS” in the supplemental Owner’s
Manual for the audio/navigation system.
The clock will be adjusted automatically.
NOTE
Depending on the model of smart-
phone, the settings of the connected
smartphone may need to be changed.
(ex: For iOS or other models, notifica-
tion settings may need to be activated.)
For details, check the instructions on
connecting smartphones.
& Regulatory information
S03AF04
The Bluetooth
®
word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc.
Light control switch
S03AH
& Precautions and tips
S03AH06
CAUTION
. Use of any lights for a long period
of time while the engine is not
running can cause the battery to
discharge.
. Before leaving the vehicle, make
sure that the lights are turned off.
If the vehicle is left unattended
for a long time with the lights
illuminated, the battery may be
discharged.
NOTE
. Even if the key is removed from the
ignition switch, the lights can be illumi-
nated by operating the light control
switch from the “
” (off) position to the
“
” or “ ” position (models without
“keyless access with push-button sys-
tem”).
. Even if the push-button ignition
switch is turned off, the lights can be
illuminated by operating the light con-
trol switch from the “
” (off) position to
the “
” or “ ” position (models with
“keyless access with push-button start
Instruments and controls/Light control switch
3-68
(207,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
system”).
. If the driver’s door is opened while
the lights are illuminated and the key is
removed from the ignition switch, the
chirp sound will inform the driver that
the lights are illuminated.
& Headlights
S03AH01
Except for Canada models
For Canada models
To turn on the headlights, turn the knob on
the end of the turn signal lever.
“
” position:
Instrument panel illumination, headlights,
parking lights, front side marker lights, rear
side marker lights, tail lights and license
plate lights are on.
“
” position:
Instrument panel illumination, parking
lights, front side marker lights, rear side
marker lights, tail lights and license plate
lights are on.
“
” position (if equipped):
Auto on/off headlights
When the ignition switch is in the “ON”
position, the instrument panel illumination,
headlights, parking lights, front side mar-
ker lights, rear side marker lights, tail lights
and license plate lights are automatically
on or off depending on the level of the
ambient light.
NOTE
. The sensitivity of the auto on/off
headlights can be changed by a
SUBARU dealer. Consult your SUBARU
dealer for details. Also, for models with
a combination meter display (color
LCD), the setting can be changed using
the display. For details, refer to “Vehicle
Setting” F3-42.
. If the light control switch is in the
“AUTO” position and the headlights do
not turn on when it becomes dark
outside, turn the light switch to the
“
” position. When this happens, have
your vehicle inspected by your
SUBARU dealer as soon as possible.
Auto-on/off wiper-linked headlights
While the light control switch is in the
“AUTO” position, the headlights will auto-
matically turn on when the windshield
wipers operate several times. The head-
lights will automatically turn off when the
wipers stop.
– CONTINUED –
Instruments and controls/Light control switch
3-69
3
(208,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
NOTE
The ON/OFF setting of this function can
be changed by a SUBARU dealer.
Consult your SUBARU dealer for de-
tails.
“
” position (except for Canada mod-
els):
The headlights are all off.
“OFF” position (for Canada models):
The headlights are all off *
1
*
2
.
*1: When the light switch is switched to the
“OFF” position while the vehicle is stopped,
the lights turn off. Then the light switch will
automatically return to the “AUTO” position.
*2: The headlights will automatically change to
the AUTO mode when the following condi-
tions are met:
. The engine is running.
. The parking brake is fully released.
. For CVT models, the select lever is in a
position other than the “P” position.
! Welcome lighting function (if
equipped)
S03AH0103
The welcome lighting function turns on the
low beam headlight for smooth approach-
ing to or exiting from the vehicle at night or
in a dark place.
The function is activated while all of the
following conditions are met.
. The light control switch is in the “AUTO”
position.
. It is dark enough to turn on the auto on/
off headlights.
NOTE
If the engine is turned off after turning
off the light switch, the welcome light-
ing function may not operate (for
Canada models).
When approaching:
While the welcome lighting function is
activated, the low beam headlights, park-
ing lights, front side marker lights, rear side
marker lights, tail lights and license plate
lights will automatically illuminate when
unlocking the doors and the rear gate by
using the remote keyless entry system.
The lights will remain illuminated for 30
seconds*
1
and then turn off. However, if
any of the following operations is done, the
light will turn off.
. The doors are locked.
. The light control switch is turned to a
position other than “AUTO”.
. The ignition switch is turned to the “ON”
position.
When exiting:
While the welcome lighting function is
activated, the low beam headlights, park-
ing lights, front side marker lights, rear side
marker lights, tail lights and license plate
lights will remain illuminated even when
either of the following operation is done.
. The push-button ignition switch is
turned to the “OFF” status (models with
“keyless access with push-button start
system”).
. The key is pulled out from the ignition
switch (models without “keyless access
with push-button start system”).
The lights will turn off under any of the
following conditions.
. 3 minutes have passed since the light
were illuminated by the welcome lighting
function.
. 30 seconds have passed since the door
is opened and closed.*
1
. The light control switch is turned to a
position other than “AUTO”.
. The locking procedure is performed
twice. When performing the unlocking
procedure after performing the locking
procedure, perform the locking procedure
twice again.
*1: The setting for the period of time in which the
lights remain on by the welcome lighting
function can be changed by a SUBARU
Instruments and controls/Light control switch
3-70
(209,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
dealer. Contact your SUBARU dealer for
details.
! Sensor for the auto on/off head-
lights (if equipped)
S03AH0101
The sensor is on the instrument panel as
shown in the illustration.
CAUTION
If any object is placed on or near the
sensor, the sensor may not detect
the level of the ambient light cor-
rectly and the auto on/off headlights
may not operate properly.
& High/low beam change (dim-
mer)
S03AH02
1) High beam
2) Low beam
When the headlights are on high beam, the
high beam indicator light “
” on the
combination meter is also on.
& Headlight flasher
S03AH03
CAUTION
Do not hold the lever in the flashing
position for more than just a few
seconds.
To flash the headlights, pull the lever
toward you and then release it. The high
beam will stay on for as long as you hold
the lever.
When the headlights are on high beam, the
high beam indicator light “
” on the
combination meter also illuminates.
– CONTINUED –
Instruments and controls/Light control switch
3-71
3
(210,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& High beam assist function (if
equipped)
S03AH07
NOTE
. The high beam assist function uti-
lizes the stereo camera installed at the
position of the front map lights.
. For details on how to handle the
stereo camera, refer to the Owner’s
Manual supplement for the EyeSight
system.
The high beam assist function automati-
cally changes the headlight from high
beam to low beam (or vice versa).
When all of the following conditions are
met, the headlight will change to high
beam.
. When the vehicle speed increases to or
above 20 mph (32 km/h).
. There is no preceding or oncoming
vehicle.
. The forward area of the vehicle is dark.
. The road does not have a sharp curve.
When any of the following conditions is
met, the headlight will change to low beam.
. When the vehicle speed decreases to
or below 10 mph (16 km/h).
. When the forward area of the vehicle is
bright.
. When there is a preceding or oncoming
vehicle.
. When the EyeSight system is malfunc-
tioning or is temporarily stopped.
NOTE
. Do not overestimate the capacity of
the high beam assist function. The
driver always has the responsibility to
understand the surrounding situation,
to drive safely, and to change the
headlight mode manually if necessary.
. The factory setting (default setting)
for this function is set as “operational”.
This setting can be changed to OFF
(non-operation) at SUBARU dealers.
For more details, contact a SUBARU
dealer.
! How to use the high beam assist
function
S03AH0701
The high beam assist function will be
activated when all the following conditions
are met.
. The light control switch is in the “AUTO”
position and the low beam headlights are
on automatically.
. The turn signal lever is pushed forward.
High beam assist indicator light
When the high beam assist function is
activated, the high beam assist indicator
light on the combination meter will illumi-
nate.
NOTE
If the high beam assist function is
malfunctioning or is temporarily
stopped, the headlight will be fixed at
low beam.
Instruments and controls/Light control switch
3-72
(211,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! How to temporarily lower the sensi-
tivity of the high beam assist func-
tion
S03AH0704
The sensitivity of the high beam assist
function can be lowered by performing the
following operations.
1. Before turning the ignition switch to the
“ON” position, set the light control switch to
the “AUTO” position and push the signal
lever forward (high beam position).
2. Turn the ignition switch to the “ON”
position and within approximately 15 sec-
onds, press the “
/ ” (following distance
setting) switch more than 10 times con-
secutively.
When the sensitivity of the high beam
assist function is lowered, the high beam
assist indicator light “
” on the combina-
tion meter will flash.
NOTE
. The sensitivity of the high beam
assist function cannot be lowered in
the following conditions.
– Cruise control or Adaptive Cruise
Control indicator is illuminated.
– The EyeSight warning indicator
(yellow) is illuminated.
. The sensitivity of the high beam
assist function returns to normal level
the next time the ignition switch is
turned to the “LOCK”/“OFF” position
and the engine is restarted.
! How to change the headlight mode
manually
S03AH0702
Change to the low beam:
When you return the turn signal lever to the
center position, the high beam assist
function will turn off and the high beam
assist indicator light will turn off.
Change to the high beam:
When you turn the light control switch to
the “
” position, the headlight mode will
be changed to the high beam.
At this time, the high beam assist function
will turn off, the high beam assist indicator
light will turn off and the high beam
indicator light will turn on.
NOTE
. After manually changing the head-
light mode to the high beam, if you turn
on the high beam assist function,
return the light control switch to the
“AUTO” position.
. When manually changing the head-
light mode to the high beam, if you turn
the light control switch to the “
”
position, the instrument panel illumina-
tion, parking lights, front side marker
lights, rear side marker lights, tail lights
and license plate lights will be on.
! Tips for the high beam assist sys-
tem
S03AH0703
. The high beam assist function recog-
nizes the conditions surrounding the ve-
hicle based on the brightness of illumina-
tion ahead of your vehicle, etc. Therefore,
the headlight mode may switch in some
situations that do not match to the driver’s
sense.
. A bicycle or cargo cycle may not be
detected.
. Under the following situations, the
brightness of ambient illumination may
not be detected correctly and the high
beam assist function may not work prop-
erly. As a result, the glare of the high beam
may disturb the oncoming vehicle or
vehicle ahead. Also, the low beam mode
may continue although there are no
oncoming vehicles and vehicles ahead.
In the such cases, change the headlight
mode manually.
– In bad weather (fog, snow, sand
storm, heavy rain, etc.).
– When the windshield glass is dirty or
fogged.
– When the windshield is cracked or
damaged.
– When the stereo camera is de-
formed or the stereo camera lenses
– CONTINUED –
Instruments and controls/Light control switch
3-73
3
(212,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
are dirty.
– If there are lights similar to the
headlights or the tail lights in the
surrounding area.
– When an oncoming vehicle or ve-
hicle ahead is driven without its head-
lights and tail lights on.
– If the headlights of an oncoming
vehicle or the tail lights of a vehicle
ahead are dirty or discolored, or if the
light beams are not aimed correctly.
– When a rapid change of brightness
continues while driving.
– When driving on a road with many
ups and downs or uneven surfaces.
– When driving on a road with many
curves.
– When there are some objects that
reflect light strongly, such as a road
sign or a mirror in vehicle ahead.
– When the rear part of the vehicle
ahead, such as a container, reflects
light strongly.
– When the headlights of your vehicle
are damaged or dirty.
– When your vehicle is tilted, such as
in case the vehicle has a flat tire or is
being towed.
– Immediately after the engine has
started.
. In the following conditions, the head-
light mode will not be automatically chan-
ged from the high beam to the low beam.
– When your vehicle passes an on-
coming vehicle suddenly in a blind
curve.
– When another vehicle passes in
front of your vehicle.
– When an oncoming vehicle or ve-
hicle ahead comes in and out of view
because of continuous curves, median
strips, roadside trees, etc.
. If the stereo camera detects the light of
the front fog lights of an oncoming vehicle,
the headlight mode may change from the
high beam to the low beam automatically.
. The headlight mode may change from
the high beam to the low beam, or the low
beam mode may continue, when affected
by a street light, traffic signal, illumination
of an advertisement board, or a reflective
object such as a road sign and signboard.
. The timing of the change of headlight
mode may differ due to the following
factors.
– Color or brightness of the headlights
of an oncoming vehicle or the tail lights
of a vehicle ahead.
– The headlights of the oncoming
vehicle or the tail lights of the vehicle
ahead are covered with mud, snow,
etc.
– Movement and direction of an on-
coming vehicle or a vehicle ahead.
– When the headlights of an oncom-
ing vehicle or the tail lights of a vehicle
ahead illuminate on only one side.
– When the oncoming vehicle or
vehicle ahead is a motorcycle.
– Conditions of a road (slope, curve,
road surface, etc.).
– Number of passengers and weight
of loaded cargo.
– Limitation of the detection ability of
the stereo camera.
& Daytime running light system
S03AH04
WARNING
When the daytime running lights are
illuminated, the tail lights do not
illuminate. When it becomes dark
outside, turn the light switch to the
“
” position to illuminate the head-
lights and tail lights. This will im-
prove visibility and allow other dri-
vers to see your vehicle more easily.
The daytime running lights will automati-
cally illuminate when the following condi-
tions are fulfilled.
. The engine is running.
. The parking brake is fully released.
. The light control switch is in “AUTO” (if
equipped), “
” or “ ” (except for
Instruments and controls/Light control switch
3-74
(213,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Canada models).
. The light control switch is in “AUTO”,
“
” or “OFF” (for Canada models).
. For CVT models, the select lever is in a
position other than the “P” position.
NOTE
When the light switch is in the “
”
position, the instrument panel illumina-
tion, front side marker lights, tail lights
and license plate lights are also illumi-
nated.
Steering Responsive Head-
light (SRH) (if equipped)
S03BL
1) The target area of illumination when SRH
is activated
2) The target area of illumination when SRH
is not activated
SRH is a function that automatically moves
the headlight beam to the left or right in
accordance with the steering angle and
vehicle speed. This function helps to
improve the visibility at night by illuminat-
ing the road ahead at corners and inter-
sections.
You can turn the SRH function on or off by
pressing the SRH OFF switch.
1) SRH OFF indicator light
The SRH OFF indicator light on the
combination meter turns off when SRH is
turned on.
– CONTINUED –
Instruments and controls/Steering Responsive Headlight (SRH)
3-75
3
(214,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
The SRH OFF indicator light on the
combination meter illuminates when SRH
is turned off.
If SRH is malfunctioning, the SRH OFF
indicator light on the combination meter
flashes when the ignition switch is in the
“ON” position. It indicates that SRH has
been deactivated. Contact a SUBARU
dealer for an inspection.
NOTE
. If you turn the ignition switch to the
“OFF” position with SRH turned off and
then start the engine again, SRH will
automatically turn on.
. When you turn the ignition switch to
the “ON” position, the SRH OFF indi-
cator light will illuminate and turn off
after several seconds.
. SRH only activates when the vehicle
is traveling forward at the speed of
approximately 5 mph (8 km/h) or more.
. SRH may not activate when the shift
lever (MT models) is selected in 1st
gear.
Headlight beam leveler
(models with LED headlights)
S03AT
The LED headlights produce more light
than conventional halogen headlights.
When the vehicle is carrying a heavy load
and the headlight beams are angled
upwards, the driver of an oncoming vehicle
may experience glare.
To prevent this, the automatic headlight
beam leveler adjusts the headlights to the
optimum height automatically depending
on the load the vehicle is carrying.
CAUTION
For CVT models, in certain circum-
stances, the headlights may become
misaligned, and the headlight beam
leveler will not reset them to the
proper angle. This may occur after
transporting your vehicle on a flat-
bed truck, or if the vehicle is parked
and restarted on different angles. In
such cases, have the headlight
alignment checked by a SUBARU
dealer.
Fog light switch (if equipped)
S03BA
Except for Canada models
1) Headlight switch
2) Fog light switch
Instruments and controls/Headlight beam leveler (models with LED headlights)
3-76
(215,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
For Canada models
1) Headlight switch
2) Fog light switch
The front fog lights will turn on when the
fog light switch is placed in the “
” position
while the headlights are in the following
condition.
. The headlight switch is in the “
”
position with the low beam mode selected.
. For models with the auto on/off head-
lights, while the headlight switch is in the
“AUTO” position and the low beam head-
lights turn on automatically.
To turn off the front fog lights, perform the
following.
. Turn the switch to “
” (except for
Canada models).
. Turn the switch to “OFF” (for Canada
models).
Indicator light
The indicator light on the combination
meter will illuminate when the front fog
lights are illuminated.
Turn signal lever
S03AI
1) Right turn
2) Lane change right signal
3) Lane change left signal
4) Left turn
If the lever does not return after cornering,
return the lever to the neutral position by
hand.
To signal a lane change, push the turn
signal lever up or down slightly and hold it
during the lane change. The lever will
return automatically to the neutral position
when you release it.
– CONTINUED –
Instruments and controls/Turn signal lever
3-77
3
(216,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& One-touch lane changer
S03AI01
To flash the turn signal and turn signal
indicator light three times, push the turn
signal lever up or down slightly and
immediately release it.
NOTE
The operational/non-operational
setting of the one-touch lane changer
can be changed by a SUBARU dealer.
Contact the nearest SUBARU dealer for
details. For models with the combina-
tion meter display (color LCD), the
setting can also be changed by operat-
ing the combination meter display
(color LCD). For details, refer to “Vehi-
cle Setting” F3-42.
Wiper and washer
S03AM
WARNING
In freezing weather, do not use the
windshield washer until the wind-
shield is sufficiently warmed by the
defroster.
Otherwise the washer fluid can
freeze on the windshield, blocking
your view.
CAUTION
. Do not operate the washer con-
tinuously for more than 10 sec-
onds, or when the washer fluid
tank is empty. This may cause
overheating of the washer motor.
Check the washer fluid level fre-
quently, such as at fuel stops.
. Do not operate the wipers when
the windshield or rear window is
dry. This may scratch the glass,
damage the blade rubbers and
might cause the wiper motor to
fail. Before operating the wiper
on a dry windshield or rear win-
dow, always use the windshield
washer.
. In freezing weather, be sure that
the blade rubbers are not frozen
to the windshield or rear window
before switching on the wipers.
Attempting to operate the wiper
with the blades frozen to the
window glass could cause not
only the blade rubbers to be
damaged but also might cause
the wiper motor to fail. If the blade
rubbers are frozen to the window
glass, be sure to operate the
defroster, windshield wiper dei-
cer (if equipped) or rear window
defogger before turning on the
wiper.
. If the wipers stop during opera-
tion because of ice or some other
obstruction on the window, this
might cause the wiper motor to
fail even if the wiper switch is
turned off. If this occurs,
promptly stop the vehicle in a
safe place, turn the ignition
switch to the “LOCK”/“OFF” po-
sition and clean the window glass
to allow proper wiper operation.
. Use clean water if windshield
washer fluid is unavailable. In
areas where water freezes in
winter, use SUBARU Windshield
Washer Fluid or the equivalent.
Instruments and controls/Wiper and washer
3-78
(217,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Refer to “Windshield washer
fluid” F11-29.
. Do not clean the blade rubbers
with gasoline or a solvent, such
as paint thinner or benzine. This
will cause deterioration of the
blade rubbers.
NOTE
. The windshield wiper motor is pro-
tected against overloads by a circuit
breaker. If the motor operates continu-
ously under an unusually heavy load,
the circuit breaker may trip to stop the
motor temporarily. If this happens, park
your vehicle in a safe place, turn off the
wiper switch, and wait for approxi-
mately 10 minutes. The circuit breaker
will reset itself, and the wipers will
again operate normally.
. Clean your blade rubbers and win-
dow glass periodically with a washer
solution to prevent streaking, and to
remove accumulations of road salt or
road film. Operate the windshield
washer for at least 1 second so that
washer solution will be sprinkled all
over the windshield or rear window.
. Grease, wax, insects or other mate-
rial on the windshield or the blade
rubbers results in jerky wiper operation
and streaking on the glass. If you
cannot remove those streaks after
operating the washer or if the wiper
operation is jerky, clean the outer sur-
face of the windshield or rear window
and the blade rubbers using a sponge
or soft cloth with a neutral detergent or
mild-abrasive cleaner. After cleaning,
rinse the window glass and blade
rubbers with clean water. The glass is
clean if no beads form on the glass
when you rinse with water.
. If you cannot eliminate the streaking
even after following this procedure,
replace the blade rubbers with new
ones. For replacement instructions,
refer to “Replacement of wiper blades”
F11-30.
& Windshield wiper and washer
switches
S03AM01
The wiper operates only when the ignition
switch is in the “ON” position.
! Operating the wiper lever
S03AM0106
: Mist operation (for a single wipe)
: Off
: Intermittent operation
: Low speed operation
:
High speed operation
For a single wipe of the wipers, push the
lever up. The wipers operate until you
release the lever.
– CONTINUED –
Instruments and controls/Wiper and washer
3-79
3
(218,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! Wiper intermittent time control
S03AM0103
When the wiper switch is in the “ ”
position, turn the dial to adjust the operat-
ing interval of the wiper. The operating
interval can be adjusted in several steps
from the shortest interval to the longest.
! Windshield washer
S03AM0104
To wash the windshield, pull the wiper
control lever toward you. The washer fluid
sprays until you release the lever. The
wipers operate while you pull the lever.
NOTE
Windshield washer fluid warning light
The windshield washer fluid warning
light illuminates when the washer fluid
level in the tank has dropped to the
lower limit. If the warning light illumi-
nates, refill the tank with fluid. For the
refilling procedure, refer to “Wind-
shield washer fluid” F11-29.
Instruments and controls/Wiper and washer
3-80
(219,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
& Rear window wiper and
washer switch
S03AM02
:
Washer operation (accompanied by
wiper operation)
:
Continuous operation
:
Intermittent operation
:
Off
:
Washer operation (accompanied by
wiper operation)
! Rear wiper
S03AM0201
With the switch turned to the “ ” position,
the rear wiper will operate intermittently at
intervals corresponding to the vehicle
speed. In this position, when you move
the select lever to the “R” position (CVT
models) or the shift lever to the reverse
position (MT models), the rear wiper will
switch to continuous operation. When you
move the select lever/shift lever from the
“R” (reverse) position to another position,
the rear wiper will return to intermittent
operation.
Reverse gear interlocked rear wiper:
Even if the rear wiper switch is in the off
“
” position, if the front windshield wiper is
operating continuously, the rear wiper will
operate intermittently when you move the
select lever/shift lever to the “R” (reverse)
position.
The factory setting (default setting) of the
reverse gear interlocked rear wiper is as
follows.
. U.S.-spec. models: Non-operational
. Other models: Operational
This setting can be changed by a SUBARU
dealer. Consult your SUBARU dealer for
details.
CAUTION
Do not attach anything that disturbs
the rear wiper operation on the rear
gate. Doing so may damage the rear
wiper when it operates.
! Washer
S03AM0202
To wash the rear window, turn the knob to
the “
” position. The washer fluid sprays
and the wiper operates until you release
the knob.
Instruments and controls/Wiper and washer
3-81
3
(220,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Mirrors
S03AP
Always check that the inside and outside
mirrors are properly adjusted before you
start driving.
& Inside mirror
S03AP01
1) Normal position
2) Anti-glare position
Push the tab on the mirror for normal use.
To reduce glare from the headlights of the
vehicle behind you, pull the tab to the anti-
glare position.
& Auto-dimming mirror/com-
pass (if equipped)
S03AP02
1) Display
2) Switch
During nighttime driving, the auto-dimming
feature senses distracting glare from
vehicle headlights behind you and auto-
matically dims to eliminate the glare and
preserve your vision.
! To Operate the Auto-Dimming Fea-
ture
S03AP0205
Press the “ ” switch to turn the auto-
dimming feature on/off. The auto-dimming
feature is enabled when the switch’s green
LED indicator is on. The auto-dimming
feature will default to on with each ignition
cycle.
! To Operate the Compass Feature
S03AP0206
1. To turn the compass feature on/off,
press and hold the “
” switch for more
than 3 seconds or until the display turns
on/off. The compass feature will default to
on with each ignition cycle.
2. If the display reads “C”, slowly drive the
vehicle in circles until compass is cali-
brated.
Compass calibration zones
Instruments and controls/Mirrors
3-82
(221,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
3. To adjust for compass zone variance:
(1) Find your current location and
zone number on the map.
(2) Press and hold the “
” switch for
more than 6 seconds or until a zone
number appears in the display.
(3) Once the zone number appears in
the display, toggle the “
” switch
again until your current location zone
number appears. After you stop press-
ing the switch, your new zone number
will be saved. Within a few seconds,
the display will show a compass direc-
tion.
4. If the vehicle’s magnetics have chan-
ged or if the compass appears inaccurate,
recalibrate the compass. Press and hold
the “
” switch for more than 9 seconds or
until a “C” appears in the display. Once a
“C” appears in the display, slowly drive the
vehicle in circles until compass is cali-
brated.
& Auto-dimming mirror/com-
pass with HomeLink
®
(if
equipped)
S03AP07
1) Display
2) HomeLink Buttons
3) Switch
During nighttime driving, the auto-dimming
feature senses distracting glare from
vehicle headlights behind you and auto-
matically dims to eliminate the glare and
preserve your vision.
! To Operate the Auto-Dimming Fea-
ture
S03AP0705
Press the “ ” switch to turn the auto-
dimming feature on/off. The auto-dimming
feature is enabled when the switch’s green
LED indicator is on. The auto-dimming
feature will default to on with each ignition
cycle.
! To Operate the Compass Feature
S03AP0706
1. To turn the compass feature on/off,
press and hold the “
” switch for more
than 3 seconds or until the display turns
on/off. The compass feature will default to
on with each ignition cycle.
2. If the display reads “C”, slowly drive the
vehicle in circles until compass is cali-
brated.
Compass calibration zones
3. To adjust for compass zone variance:
(1) Find your current location and
zone number on the map.
(2) Press and hold the “
” switch for
more than 6 seconds or until a zone
number appears in the display.
(3) Once the zone number appears in
– CONTINUED –
Instruments and controls/Mirrors
3-83
3
(222,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
the display, toggle the “ ” switch
again until your current location zone
number appears. After you stop press-
ing the switch, your new zone number
will be saved. Within a few seconds,
the display will show a compass direc-
tion.
4. If the vehicle’s magnetics have chan-
ged or if the compass appears inaccurate,
recalibrate the compass. Press and hold
the “
” switch for more than 9 seconds or
until a “C” appears in the display. Once a
“C” appears in the display, slowly drive the
vehicle in circles until compass is cali-
brated.
! HomeLink
®
Wireless Control Sys-
tem
S03AP0704
The HomeLink
®
Wireless Control System
provides a convenient way to replace up to
three hand-held radio-frequency remotes
used to activate devices such as gate
operators, garage door openers, entry
door locks, security systems, even home
lighting. The below steps are generic
programming instructions; for Genie and
Sommer garage door openers please go
directly to the HomeLink website. Addi-
tional information and programming vi-
deos can be found at
www. and
www.
CAUTION
. Before programming HomeLink
to a garage door opener or gate
operator, make sure that people
and objects are out of the way of
the device to prevent potential
harm or damage.
. When programming a garage
door opener, it is advised to park
outside of the garage.
. Do not use HomeLink with any
garage door opener that lacks
safety stop and reverse features
as required by U.S. federal safety
standards (this includes any gar-
age door opener model manufac-
tured before April 1, 1982). A
garage door that cannot detect
an object signaling the door to
stop and reverse does not meet
current U.S. federal safety stan-
dards.
. It is also recommended that a new
battery be placed in the hand-
held remote (garage door opener
remote) of the device for quicker
and more accurate training.
. Some vehicles may require the
ignition switch to be turned to the
“ON” or “ACC” position for pro-
gramming and/or operation of
HomeLink.
. Keep the hand-held remote (gar-
age door opener remote) of the
device you are programming for
use in other vehicles as well as
for future HomeLink program-
ming. It is also suggested that
upon the sale of the vehicle, the
programmed HomeLink buttons
be erased for security purposes.
Refer to “Erasing HomeLink But-
tons” F3-87.
! Programming a New HomeLink
Button
S03AP070409
1) Indicator Light
2) HomeLink Buttons
Instruments and controls/Mirrors
3-84
(223,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
1. Press and release the HomeLink but-
ton that you would like to program. The
HomeLink indicator light will flash orange
slowly (if not, refer to “Erasing HomeLink
Buttons” F3-87).
1) Garage door opener remote
2. Position the hand-held remote (garage
door opener remote) 1 to 3 inches (2 to 8
cm) away from the HomeLink button that
you would like to program.
NOTE
Some hand-held remotes (garage door
opener remotes) may actually train
better at a distance of 6 to 12 inches
(15 to 30 cm). Keep this in mind if you
have difficulty with the programming
process.
3. While the HomeLink indicator light is
flashing orange, press and hold the hand-
held remote button. Continue pressing the
hand-held remote button until the
HomeLink indicator light changes from
orange to green. You may now release
the hand-held remote button.
NOTE
Some devices may require you to re-
place this “Programming a New
HomeLink Button” step 3 with proce-
dures noted in the “Gate Operator /
Canadian Programming” section. Refer
to “Gate Operator / Canadian Program-
ming” F3-87.
1) Indicator Light
4. Press the HomeLink button that you
would like to program and observe the
indicator light.
. If the indicator light remains constant
green, your device should operate
when the HomeLink button is pressed.
At this point, if your device operates,
programming is complete.
. If the indicator light rapidly flashes
green, firmly press, hold for two sec-
onds and release the HomeLink button
up to three times to complete the
programming process. At this point if
your device operates, programming is
complete. If the device does not
operate, continue with the next step
of the programming instructions.
– CONTINUED –
Instruments and controls/Mirrors
3-85
3
(224,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
1) “Learn” button
5. At the garage door opener motor,
(security gate motor, etc.) locate the
“Learn”, “Smart”, or “Program” button. This
can usually be found where the hanging
antenna wire is attached to the motor-head
unit (see the device’s manual to identify
this button). The name and color of the
button may vary by manufacturer.
NOTE
A ladder and/or second person may
simplify the following steps.
6. Firmly press and release the “Learn”,
“Smart”, or “Program” button. You now
have 30 seconds in which to complete step
7.
7. Return to the vehicle and firmly press,
hold for two seconds and release the
HomeLink button up to three times. At this
point programming is complete and your
device should operate when the HomeLink
button is pressed and released.
1) Status Indicators
8. If status indicator arrows appear next
to the indicator light, please refer to
“Garage Door Two-Way Communication”
F3-87.
In the event that there are still program-
ming difficulties or questions, additional
HomeLink information and programming
videos can be found at
www. and
www. For
Genie and Sommer garage door openers
please go directly to the HomeLink web-
site.
Instruments and controls/Mirrors
3-86
(225,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
! Gate Operator / Canadian Pro-
gramming
S03AP070410
Canadian radio-frequency laws require
transmitter remote signals to “time-out”
(or quit) after several seconds of transmis-
sion, which may not be long enough for
HomeLink to pick up the signal during
programming. Similar to this Canadian
law, some U.S. gate operators are de-
signed to “time-out” in the same manner.
The indicator LED on the hand-held
remote will go off when the device times
out, indicating that it has finished transmit-
ting.
If you live in Canada or you are having
difficulties programming a gate operator or
garage door opener by using the program-
ming procedures, replace “Programming a
New HomeLink Button” step 3 with the
following:
While the HomeLink indicator light is
flashing orange, press and release (“cy-
cle”) your device’s hand-held remote every
two seconds until the HomeLink indicator
light changes from orange to green. You
may now release the hand-held remote
button.
NOTE
If programming a garage door opener
or gate operator, it is advised to unplug
the device during the “cycling” process
to prevent possible overheating.
Proceed with “Programming a New
HomeLink Button” step 4 to complete.
! Using HomeLink
S03AP070411
To operate, simply press and release the
programmed HomeLink button. Activation
will now occur for the trained device (i.e.
garage door opener, gate operator, secur-
ity system, entry door lock, home/office
lighting, etc.). For convenience, the hand-
held remote of the device may also be
used at any time.
! Erasing HomeLink Buttons
S03AP070412
To erase programming from the three
buttons (individual buttons cannot be
erased but can be “reprogrammed” as
outlined below), follow the step noted:
Press and hold the two outer HomeLink
buttons for at least 10 seconds. The LED
indicator will change from continuously lit
to rapidly flashing. Release both buttons.
Do not hold for longer than 20 seconds.
HomeLink is now ready to be programmed
at any time beginning with “Programming a
New HomeLink Button” - step 1.
! Reprogramming a Single
HomeLink Button
S03AP070406
To program a previously trained button,
follow these steps:
1. Press and hold the desired HomeLink
button. DO NOT release the button.
2. The indicator light will begin to slowly
flash orange after 20 seconds. The
HomeLink button can be released at this
point. Proceed with “Programming a New
HomeLink Button” - step 3.
3. If you do not complete the program-
ming of a new device to the button, it will
revert to the previously stored program-
ming.
! Garage Door Two-Way Commu-
nication
S03AP070413
HomeLink has the capability of commu-
nicating with your garage door opener.
HomeLink can receive and display “clos-
ing” or “opening” status messages from
compatible garage door opener systems.
At any time, HomeLink can also recall and
display the last recorded status commu-
nicated by the garage door opener to
indicate your garage door being “closed”
or “opened”.
HomeLink has the capability of receiving
this communication from the garage door
opener at a range up to 820 feet (250 m).
– CONTINUED –
Instruments and controls/Mirrors
3-87
3
(226,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Range may be reduced by obstacles such
as houses or trees. You may have to slow
your vehicle speed to successfully receive
the garage door opener communication.
! Programming Two-Way Commu-
nication
S03AP070414
1) Status Indicators
Within five seconds after programming a
new HomeLink button, both of HomeLink’s
garage door status indicators will flash
rapidly green indicating that the garage
door two-way communication has been
enabled. If your garage door status in-
dicators flashed, two-way communication
programming is complete.
If the garage door status indicators do not
flash, additional HomeLink information
and programming videos can be found
online at www. and
www.
! Using Two-Way Communication
S03AP070415
1) Status Indicators
Recall and display (at any time) the last
recorded garage door status message
communicated to HomeLink by simulta-
neously pressing HomeLink buttons 1 and
2 for two seconds. HomeLink will display
the last recorded status for three seconds.
1) Garage Door Opener CLOSING (Blinking
Orange)
2) Garage Door Opener CLOSED (Solid
Green)
3) Garage Door Opener OPENING (Blink-
ing Orange)
4) Garage Door Opener OPENED (Solid
Green)
If two-way communication programming is
successful, HomeLink will display the
status of your garage door opener with
arrow indicators.
! Certification
S03AP070416
In the event that there are still program-
ming difficulties or questions, additional
HomeLink information and programming
videos can be found at
www.,
www. or
Instruments and controls/Mirrors
3-88
(227,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
by calling the toll-free HomeLink-hotline at
1-800-355-3515.
. U.S.-spec. models
CAUTION
FCC WARNING
Changes or modifications not ex-
pressly approved by the party re-
sponsible for compliance could void
the user’s authority to operate the
equipment.
. Canada-spec. models
– CONTINUED –
Instruments and controls/Mirrors
3-89
3
(228,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
HomeLink
®
and the HomeLink
®
house are
registered trademarks of Gentex Corpora-
tion.
WARNING
. When programming the
HomeLink
®
Wireless Control Sys-
tem, you may be operating a
garage door opener or other
device. Make sure that people
and objects are out of the way of
the garage door or other device
to prevent potential harm or da-
mage.
. Do not use the HomeLink
®
Wire-
less Control System with a gar-
age door opener that lacks the
safety stop and reverse feature
as required by applicable safety
standards. A garage door opener
which cannot detect an object,
signaling the door to stop and
reverse, does not meet these
safety standards. Using a garage
door opener without these fea-
tures increases risk of serious
injury or death. For more infor-
mation, consult the HomeLink
®
website at or
call 1-800-355-3515.
& Outside mirrors
S03AP03
! Convex mirror (passenger side)
S03AP0301
WARNING
Objects look smaller in a convex
mirror and farther away than when
viewed in a flat mirror. Do not use the
convex mirror to judge the distance
of vehicles behind you when chan-
ging lanes. Use the inside mirror (or
glance backwards) to determine the
actual size and distance of objects
that you view in convex mirror.
! Remote control mirror switch
S03AP0302
: Select side to adjust
: Direction control
Instruments and controls/Mirrors
3-90
(229,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
The remote control mirrors operate only
when the ignition switch is in the “ON” or
“ACC” position.
1. Turn the control switch to the side that
you want to adjust. “L” is for the left mirror,
“R” is for the right mirror.
2. Move the control switch in the direction
you want to move the mirror.
3. Return the control switch to the neutral
position to prevent unintentional opera-
tion.
The mirrors can also be adjusted manu-
ally.
Defogger and deicer (if
equipped)
S03BI
1) Rear window defogger
2) Outside mirror defogger (if equipped)
3) Windshield wiper deicer (if equipped)
The vehicle is equipped with the defogger
and the deicer (if equipped) system. The
defogger and deicer system is activated
only when the ignition switch is in the “ON”
position.
Climate control system type A
– CONTINUED –
Instruments and controls/Defogger and deicer
3-91
3
(230,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Climate control system type B and C
1) Models without outside mirror defogger
2) Models with outside mirror defogger
To activate simultaneously the rear win-
dow defogger, outside mirror defogger (if
equipped) and windshield wiper deicer (if
equipped), press the control button that is
located on the climate control panel. The
indicator light on the control button illumi-
nates while the defogger and deicer
system is activated.
To turn them off, press the control button
again. They also turn off when the ignition
switch is turned to the “ACC” or “LOCK”/
“OFF” position.
The defogger and deicer system will
automatically shut off after approximately
15 minutes. If the rear window and the
outside mirrors have been cleared and the
windshield blade rubbers have been
deiced completely before that time, press
the control button to turn them off.
For climate control system (type B and
C), it is possible for the defogger and
deicer system to be set to continuous
operation mode by a SUBARU dealer.
Consult your SUBARU dealer for details.
Also, for models with a combination meter
display (color LCD), it is possible to set the
defogger and deicer system for the con-
tinuous operation mode. For details, refer
to “Vehicle Setting” F3-42.
CAUTION
. To prevent the battery from being
discharged, do not operate the
defogger and deicer system con-
tinuously for any longer than
necessary.
. Do not use sharp instruments or
window cleaner containing abra-
sives to clean the inner surface of
the rear window. They may da-
mage the conductors printed on
the window.
NOTE
. Turn on the defogger and deicer
system if the wipers are frozen to the
windshield.
. If the windshield is covered with
snow, remove the snow so that the
windshield wiper deicer works effec-
tively.
. While the defogger and deicer sys-
tem is in the continuous operation
mode:
– If the vehicle speed remains at 9
mph (15 km/h) or lower for 15
minutes, the windshield wiper dei-
cer system automatically stops op-
erating. However, the rear window
defogger system and outside mirror
defogger system maintain continu-
ous operation in this condition.
– If the vehicle battery voltage
drops below the permissible level,
continuous operation of the defog-
ger system and deicer system is
canceled and the system stops
operating.
Instruments and controls/Defogger and deicer
3-92
(231,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
Tilt/telescopic steering wheel
S03BF
WARNING
. Do not adjust the steering wheel
tilt/telescopic position while driv-
ing. This may cause loss of
vehicle control and result in per-
sonal injury.
. If the lever cannot be raised to the
fixed position, adjust the steering
wheel again. It is dangerous to
drive without locking the steering
wheel. This may cause loss of
vehicle control and result in per-
sonal injury.
1) Tilt adjustment
2) Telescopic adjustment
3) Tilt/telescopic lock lever
1. Adjust the seat position. Refer to “Front
seats” F1-5.
2. Pull the tilt/telescopic lock lever down.
3. Move the steering wheel to the desired
level.
4. Pull the lever up to lock the steering
wheel in place.
5. Make sure that the steering wheel is
securely locked by moving it up and down,
and forward and backward.
& Heated Steering Wheel sys-
tem (if equipped)
S03BF01
The Heated Steering Wheel system
warms the steering wheel at a constant
temperature.
1) Heated Steering Wheel switch
2) Indicator light
3) Heated area
To turn on the Heated Steering Wheel
system, pull the Heated Steering Wheel
switch when the ignition switch is in the
“ON” or “ACC” position. Then the steering
wheel will be warmed and the indicator
light on the switch will illuminate. To turn off
the Heated Steering Wheel system, pull
the switch again. Then the indicator light
will turn off.
– CONTINUED –
Instruments and controls/Tilt/telescopic steering wheel
3-93
3
(232,1)
北米Model "A1410BE-B" EDITED: 2020/ 9/ 16
CAUTION
. Use the Heated Steering Wheel
system with the engine running.
Otherwise, the battery voltage
may drop below the permissible
level and it may not be possible to
start the engine.
. There is a possibility that people
with delicate skin may suffer
slight burns even at low tempera-
tures if they use the Heated
Steering Wheel for a long period
of time. When using the Heated
Steering Wheel, always be sure to
warn the persons concerned.
. Do not cover the Heated Steering
Wheel with an object such as a
steering wheel cover. Doing so
may cause the Heated Steering
Wheel to overheat.
NOTE
. If the surface temperature of the
steering wheel is approximately above
1048F (408C) when the switch is turned
on, the system will not heat the steering
wheel. Then, the indicator light will
continue to illuminate.
. The Heated Steering Wheel system
will automatically turn off approxi-
mately 30 minutes after the system
has been turned on.
Horn
S03AR
To sound the horn, push the horn pad.
Instruments and controls/Horn
3-94

Related Topics

Key positions Key reminder chime Ignition switch light (if equipped)

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot