Get Before Driving -> Instrument cluster (Type A) (if equipped) Guide for Suzuki Baleno 4 Door First Generation (1995-2002)

2-60

BEFORE DRIVING

68PM2-01E

Instrument cluster (Type A) (if equipped)

1. Speedometer

2. Fuel gauge

3. Information display

4. Trip meter selector knob

5. Indicator selector knob

6. Warning and indicator lights

68PM00248

EXAMPLE

324 5

2-61

BEFORE DRIVING

68PM2-01E

Speedometer

The speedometer indicates vehicle speed.

Fuel gauge

68PH02202

When the ignition switch is in “ON” posi-

tion, this gauge gives an approximate indi-

cation of the amount of fuel in the fuel tank.

“F” stands for full and “E” stands for empty.

If the fuel meter indicator shows only one

segment to “E”, refill the tank as soon as

possible.

NOTE:

If the last segment blinks, it means that the

fuel is almost empty.

If the low fuel warning light (1) comes on,

fill the fuel tank immediately.

NOTE:

The activation point of the low fuel warning

light (1) varies depending on road condi-

tions (for example, slope or curve) and

driving conditions because of fuel moving

in the tank.

Refer to “Low fuel warning light” in “Warn-

ing and indicator lights” in this section for

details.

The mark (2) indicates that the fuel filler

door is located on the left side of the vehi-

cle.

(1)

(2)

EXAMPLE

2-62

BEFORE DRIVING

68PM2-01E

Brightness control

68PH02203

When the ignition switch is turned to “ON”

position, the instrument cluster lights come

on.

Your vehicle has a system to automatically

dim the brightness of the instrument panel

lights when the position lights or headlights

are on.

When the position lights and/or headlights

are ON, you can control the meter illumina-

tion intensity.

To increase the brightness of the instru-

ment panel lights, turn the brightness con-

trol knob (1) clockwise.

To reduce the brightness of the instrument

panel lights, turn the brightness control

knob (1) counterclockwise.

NOTE:

• If you do not turn the knob within several

seconds of activating, the brightness

control display will be canceled automat-

ically.

• When you reconnect the battery, the

brightness of the instrument panel lights

will be reinitialized. Readjust the bright-

ness according to your preference.

NOTE:

If you select the maximum brightness level

when the position lights or headlights are

on, the following functions will be can-

celled.

• The function which automatically dims

the brightness of instrument cluster

lights

• The function which operates with the

brightness control, except maximum

brightness level

Information display

68PH02204

(1) Trip meter selector knob

(2) Indicator selector knob

(1)

EXAMPLE

WARNING

If you attempt to adjust the display

while driving, you could lose control

of the vehicle.

Do not attempt to adjust the display

while driving.

(2)(1)

EXAMPLE

2-63

BEFORE DRIVING

68PM2-01E

68PM00249

(3) Information display

When the ignition switch is in “ON” posi-

tion, the information display shows the fol-

lowing information.

Display (A)

Clock

Display (B)

Fuel gauge

Display (C)

Trip meter / Odometer / Fuel consumption /

Driving range / Oil indicator

Display (D)

Gearshift indicator

Display (E)

Thermometer

Clock

When the ignition switch is in “ON” posi-

tion, the display (A) shows the time.

To change the time indication:

1) Push the trip meter selector knob (1)

and the indicator selector knob (2)

together.

2) To change the hour indication, turn the

indicator selector knob (2) left or right

repeatedly when the hour indication

blinks. To change the hour indication

quickly, turn and hold the indicator

selector knob (2). To set the hour indi-

cation, push the indicator selector knob

(2) and the minute indication will blink.

3) To change the minute indication, turn

the indicator selector knob (2) left or

right repeatedly when the minute indi-

cation blinks. To change the minute

indication quickly, turn and hold the

indicator selector knob (2). To set the

minute indication, push the indicator

selector knob (2).

NOTE:

When you reconnect the negative (–) ter-

minal to the battery, the clock indication will

be reinitialized. Change the indication

again to your preference.

Fuel gauge

When the ignition switch is in “ON” posi-

tion, the display (B) shows the fuel gauge.

Refer to “Fuel gauge” in this section.

Trip meter / Odometer / Fuel con-

sumption / Driving range / Oil indi-

cator

When the ignition switch is in “ON” posi-

tion, the display (C) shows one of the fol-

lowing indications, trip meter A, trip meter

B, odometer, instantaneous fuel consump-

tion, average fuel consumption, driving

range or oil indicator.

To switch the display indication (C), push

the trip meter selector knob (1) or the indi-

cator selector knob (2) quickly.

(3)

(A) (E)

(B) (C)(D)

EXAMPLE

WARNING

If you attempt to adjust the display

while driving, you could lose control

of the vehicle.

Do not attempt to adjust the display

while driving.

2-64

BEFORE DRIVING

68PM2-01E

68PM20201

(a) Trip meter A

(b) Trip meter B

(d) Instantaneous fuel consumption

(e) Average fuel consumption

(f) Driving range

NOTE:

• Indications will change when you push

and release a knob.

• The display shows estimated values.

Indications may not be the same as

actual values.

Trip meter

The trip meter can be used to measure the

distance traveled on short trips or between

fuel stops.

You can use the trip meter A or trip meter B

independently.

To reset the trip meter to zero, push and

hold the trip meter selector knob (1) for a

while when the display shows the trip

meter.

NOTE:

The indicated maximum value of the trip

meter is 9999.9. When you run past the

maximum value, the indicated value will

return to 0.0.

Odometer

The odometer records the total distance

the vehicle has been driven.

Push the trip meter selector

knob (1).

Push the indicator selector

knob (2).

(a)

(b)

(c)

(d)

(e)

(f)

EXAMPLE

WARNING

If you attempt to adjust the display

while driving, you could lose control

of the vehicle.

Do not attempt to adjust the display

while driving.

NOTICE

Keep track of your odometer reading

and check the maintenance sched-

ule regularly for required services.

Increased wear or damage to certain

parts can result from failure to per-

form required services at the proper

mileage intervals.

2-65

BEFORE DRIVING

68PM2-01E

Instantaneous fuel consumption

The display shows the value of instanta-

neous fuel consumption only when the

vehicle is moving.

NOTE:

• The display does not show the value

unless the vehicle is moving.

• Depending on the vehicle’s specification,

the fuel consumption units of initial set-

ting are indicated as L/100km, km/L or

MPG.

• For “L/100km” or “km/L” setting, the indi-

cated maximum value of instantaneous

fuel consumption is 30. No more than 30

will be indicated on the display even if

the actual instantaneous fuel consump-

tion is higher.

• For “MPG” setting, the indicated maxi-

mum value of instantaneous fuel con-

sumption is 80. No more than 80 will be

indicated on the display even if the

actual instantaneous fuel consumption is

higher.

• The indication on the display may be

delayed if fuel consumption is greatly

affected by driving conditions.

• The display shows estimated values.

Indications may not be the same as

actual values.

• For “L/100km” or “km/L” setting, you can

change the units that instantaneous fuel

consumption is displayed in. Refer to

“Average fuel consumption” in this sec-

tion.

Average fuel consumption

If you selected average fuel consumption

the last time you drove the vehicle, the dis-

play shows the last value of average fuel

consumption from previous driving when

the ignition switch is turned to “ON” posi-

tion. Unless you reset the value of average

fuel consumption, the display indicates the

value of average fuel consumption which

includes average fuel consumption during

previous driving.

To reset the average fuel consumption to

zero, push and hold the indicator selector

knob (2) for a while when the display

shows the average fuel consumption.

NOTE:

When you reset the indication or reconnect

the negative (–) terminal to the battery, the

value of average fuel consumption will be

shown after driving for a while.

(For “L/100km” or “km/L” setting)

To change the unit of average fuel con-

sumption, while pushing and holding the

trip meter selector knob (1), turn the indica-

tor selector knob (2).

68PH02207

NOTE:

• When you change the units that average

fuel consumption is displayed in, the

instantaneous fuel consumption units will

be changed automatically.

• When you reconnect the negative (–)

terminal to the battery, the unit of the

average fuel consumption will be reini-

tialized. Change the unit again to your

preference.

EXAMPLE

(Initial

setting)

2-66

BEFORE DRIVING

68PM2-01E

Driving range

If you selected driving range the last time

you drove the vehicle, the display indicates

“---” for a few seconds and then indicates

the current driving range when the ignition

switch is turned to “ON” position.

The driving range shown in the display is

the approximate distance you can drive

until the fuel gauge indicates “E”, based on

current driving conditions.

When the low fuel warning light comes on,

the display “---” will appear.

If the low fuel warning light comes on, fill

the fuel tank immediately regardless of the

value of driving range shown in the display.

As the driving range after refueling is cal-

culated based on the most recent driving

condition, the value is different each time

you refuel.

NOTE:

• If you refuel when the ignition switch is in

“ON” position, the driving range may not

indicate the correct value.

• When you reconnect the negative (–)

terminal to the battery, the value of driv-

ing range will be shown after driving for a

while.

Oil indicator

If either of odometer reading or time is

reached to the value which is set by the oil

life monitoring system, the oil change

request light comes on when the ignition

switch is in “ON” position. The “Oil” indica-

tion is shown on the Information Display

engine oil and oil filter.

68PM00269

For instructions on how to change the

engine oil and filter, refer to “Changing

engine oil and filter” in “INSPECTION AND

MAINTENANCE” section or consult your

SUZUKI dealer for advice on appropriate

procedure of engine oil and oil filter main-

tenance.

To monitor the next oil and oil filter change

timing properly, it is necessary to reset the

odometer reading and the time for the

light. The light will go out after the reset.

For the resetting procedure, it is recom-

mended to consult your SUZUKI dealer. If

you reset it by yourself, follow the proce-

dure described below:

To reset the engine oil life monitoring sys-

tem:

1) Turn the ignition key to “ON” position.

2) Push and hold the indicator selector

knob (2) for a while when the display

shows the oil change request light and

oil indicator.

68PM00270

EXAMPLE

(2)

EXAMPLE

2-67

BEFORE DRIVING

68PM2-01E

3) Push and hold the indicator selector

knob (2), display will change as follows.

When the oil life monitoring system is

reset, the oil change request light and

oil indicator will go out and then the dis-

play indicates odometer.

68PM20204

Gearshift indicator

Refer to “Gearshift indicator” in “OPERAT-

ING YOUR VEHICLE” section.

Thermometer

When the ignition switch is in “ON” posi-

tion, the display (E) shows the thermome-

ter.

The thermometer indicates the outside

temperature.

76MH0A042

If the outside temperature drops to freez-

ing, the mark (g) will appear on the display.

NOTE:

• The outside temperature indication is not

the actual outside temperature when

driving at low speed, or when stopped.

• If there is something wrong with the ther-

mometer, or just after the ignition switch

is turned to “ON” position, the display

may not indicate the outside tempera-

ture.

When the display (C) shows the driving

range, you can change the unit of tem-

perature.

To change the unit of temperature, while

pushing and holding the trip meter selector

knob (1), turn the indicator selector knob

(2).

76MH0A043

NOTE:

When you reconnect the negative (–) ter-

minal to the battery, the unit of temperature

will be reinitialized. Change the unit again

to your preference.

EXAMPLE

(g)

EXAMPLE

(Initial

setting)

2-68

BEFORE DRIVING

68PM2-01E

Setting mode

In the setting mode, you can set up the following functions.

Indication Functions

Time indication of clock “ ”

Central door locking system “ ”

Additional flashes of the turn signal “ ”

Oil change request light reset setting “ ”

Tire pressure monitoring system setting

Initialization setting “ ”

Exit the setting mode “ ”

2-69

BEFORE DRIVING

68PM2-01E

NOTE:

Depending on vehicle’s specifications,

some items may not be displayed.

How to operate the setting mode:

1) When the ignition switch is in “ON”

position and the vehicle is stationary,

push the trip meter selector knob (1) to

switch the information display indication

2) Push and hold the indicator selector

knob (2) until the display shows

“ ”.

3) Turn and/or push the indicator selector

knob (2) to select a function that you

want to set up according to the above

chart.

4) Turn and/or push the indicator selector

knob (2) to register settings of the fol-

lowing functions.

Time indication of clock “ ”

• : 12-hour format (default set-

ting)

• : 24-hour format

Central door locking system “ ”

• : Unlock all doors by turning

the key once

• : Unlock all doors by turning

the key twice (default setting)

Additional flashes

of the turn signal “ ”

• : Turn signal flashes three

times after the turn signal

lever is returned (default set-

ting)

• : Disable the additional flashes

of turn signal

Oil change request light reset setting

“ ”

• : Reset of the oil life monitoring

system

Tire pressure monitoring system set-

ting

(For EU countries)

• : Comfort Mode (default set-

ting)

• : Eco Mode

• : Load Mode

(Except for EU countries)

• : Comfort Mode (default set-

ting)

• : Load Mode

Refer to “Tire pressure monitoring system

(TPMS)” in “OPERATING YOUR VEHI-

CLE” section for details.

Initialization setting “ ”

• : Initialize all settings

68PM00272

NOTE:

• As shown in the above illustration, “ ”

indicates on the display of currently set-

ting item.

• To go back to the higher level display

during operation, turn the indicator

selector knob (2) to display “ ” or

“ ” and then push the indicator

selector knob (2).

5) To exit the setting mode, switch the dis-

play to show “ ” and then push the

indicator selector knob (2).

Turn the indicator selector knob

(2).

Push the indicator selector

knob (2).

EXAMPLE

Before Driving -> Instrument cluster (Type A) (if equipped) for Your Suzuki Baleno 4 Door First Generation (1995-2002)

Related Topics

Popular Owner Manuals

Latest Owner Manuals