Get Before Driving -> Instrument cluster (Type C) (if equipped) Guide for Suzuki Baleno 4 Door First Generation (1995-2002)

2-83

BEFORE DRIVING

68PM2-01E

Instrument cluster (Type C) (if equipped)

1. Speedometer

2. Tachometer

3. Fuel gauge

4. Temperature gauge

5. Information display

6. Trip meter selector knob

7. Indicator selector knob

8. Warning and indicator lights

68PM00252

EXAMPLE

34 886 75

2 8

2-84

BEFORE DRIVING

68PM2-01E

Speedometer

The speedometer indicates vehicle speed.

Tachometer

The tachometer indicates engine speed in

revolutions per minute.

Fuel gauge

68PH02223

When the ignition mode is “ON”, this

gauge gives an approximate indication of

the amount of fuel in the fuel tank. “F”

stands for full and “E” stands for empty.

If the indicator approaches a low level

(near “E”) on fuel gauge, refill the tank as

soon as possible.

NOTE:

The indicator moves a little depending on

road conditions (for example, slope or

curve) and driving conditions because of

fuel moving in the tank.

If the low fuel warning light (1) comes on,

fill the fuel tank immediately.

Refer to “Low fuel warning light” in “Warn-

ing and indicator lights” in this section for

details.

The mark (2) indicates that the fuel filler

door is located on the left side of the vehi-

cle.

NOTICE

Never drive the vehicle with the

engine revving in the red zone or

severe engine damage can result.

Keep the engine speed below the red

zone even when downshifting to a

lower gear position.

Refer to “Downshifting maximum

allowable speeds” in “OPERATING

YOUR VEHICLE” section.

(1)

(2)

EXAMPLE

2-85

BEFORE DRIVING

68PM2-01E

Temperature gauge

68PH02224

When the ignition mode is “ON”, this

gauge indicates the engine coolant tem-

perature. Under normal driving conditions,

the indicator should stay within the normal,

acceptable temperature range between

“H” and “C”. If the indicator approaches

“H”, overheating is indicated. Follow the

instructions for “Engine trouble: Overheat-

ing” in “EMERGENCY SERVICE” section.

Brightness control

68PH02225

When the engine switch is pressed to

change the ignition mode to “ON”, the

instrument cluster lights come on.

Your vehicle has a system to automatically

dim the brightness of the instrument clus-

ter lights when the position lights or head-

lights are on.

You can change the brightness of the

instrument cluster lights regardless of

whether the position lights or headlights

are off or on.

To increase the brightness of the instru-

ment cluster lights, turn the indicator selec-

tor knob (1) clockwise.

To reduce the brightness of the instrument

cluster lights, turn the indicator selector

knob (1) counterclockwise.

NOTE:

• If you do not turn the knob within several

seconds of activating, the brightness

control display will be canceled automat-

ically.

• When you reconnect the battery, the

brightness of the instrument cluster

lights will be reinitialized. Readjust the

brightness according to your preference.

NOTE:

If you select the maximum brightness level

when the position lights or headlights are

on, the following functions will be can-

celled.

• The function which automatically dims

the brightness of instrument cluster

lights

• The function which operates with the

brightness control, except maximum

brightness level

NOTICE

Continuing to drive the vehicle when

engine overheating is indicated can

result in severe engine damage.

EXAMPLE

(1)

EXAMPLE

WARNING

Do not adjust the brightness of the

instrument panel lights while driving.

Otherwise, you could lose control of

the vehicle.

2-86

BEFORE DRIVING

68PM2-01E

Information display

The information display is shown when the

ignition mode is “ON”.

68PH02226

(1) Information display

68PM00253

(2) Indicator selector knob

(3) Trip meter selector knob

The information display shows the follow-

ing information.

Display (A)

Clock

Display (B)

Thermometer

Display (C)

Warning and indicator messages /

Fuel consumption / Driving range /

Average speed / Driving time /

Clock and date / Motion /

Torque and power / Accelerator and brake /

Energy flow (if equipped)

Display (D)

Selector position (for automatic transaxle

or CVT vehicles) / Gearshift indicator (if

equipped)

Display (E)

Trip meter

Display (F)

Odometer

68PM00279

When the engine switch is pressed to

change the ignition mode to “ON”, the

clock display shown in the above illustra-

tion will appear on the display for several

seconds.

Some warning and indicator messages

may appear on the display when the igni-

tion mode is “ACC” or “LOCK” (OFF).

(1)

(A) (B)

(C)

(D)

(E)

(F)

(2)(3)

EXAMPLE

2-87

BEFORE DRIVING

68PM2-01E

Clock

The display (A) shows the time.

To set the clock, follow “Setting mode”

instructions in this section.

Thermometer

The display (B) shows the thermometer.

The thermometer indicates the outside

temperature.

68PM00277

If the outside temperature nears freezing,

the message shown in the above illustra-

tion will appear on the display.

NOTE:

The outside temperature indication is not

the actual outside temperature when driv-

ing at low speed, or when stopped.

Fuel consumption / Driving range /

Average speed / Driving time /

Clock and date / Motion / Torque

and power / Accelerator and brake /

Energy flow (if equipped)

When there are no warning or indicator

messages on the display (C), you can

select one of the following indications to

appear on the display: instantaneous fuel

consumption, average fuel consumption,

driving range, average speed, driving time,

clock and date, motion, torque and power,

accelerator and brake, energy flow (if

equipped) or no indication.

EXAMPLE

WARNING

If you attempt to adjust the display

while driving, you could lose control

of the vehicle.

Do not attempt to adjust the display

while driving.

2-88

BEFORE DRIVING

68PM2-01E

68PM00254

(a) Instantaneous fuel consumption / Average fuel consumption / Driving range

(b) Instantaneous fuel consumption / Average fuel consumption / 5-minute average fuel consumption

(d) Clock and date

(e) Motion

(f) Torque and power

(g) Accelerator and brake

(h) Energy flow (if equipped)

(i) No indication

(a) (b) (c)

(g)(h)

(i)

(f)

(e)

(d)

EXAMPLE

To switch the display indication, push the

indicator selector knob (2) quickly.

NOTE:

The value of instantaneous fuel consump-

tion, average fuel consumption, driving

range, average speed, motion, torque and

power, accelerator and brake and energy

flow (if equipped) shown on the display are

affected by the following conditions;

• road condition

• surrounding traffic condition

• driving condition

• vehicle condition

• a malfunction which causes the malfunc-

tion indicator light to come on or blink

2-89

BEFORE DRIVING

68PM2-01E

Instantaneous fuel consumption

The display shows instantaneous fuel con-

sumption with a bar graph only when the

vehicle is moving.

68PM00280

(4) Instantaneous fuel consumption

NOTE:

• The display does not show the bar graph

unless the vehicle is moving.

• Depending on the vehicle’s specification,

the fuel consumption units of initial set-

ting are indicated as L/100km, km/L or

MPG.

• For L/100km or km/L setting, the indi-

cated maximum value of instantaneous

fuel consumption is 50. No more than 50

will be indicated on the display even if

the actual instantaneous fuel consump-

tion is higher.

• For MPG setting, the indicated maxi-

mum value of instantaneous fuel con-

sumption is 80. No more than 80 will be

indicated on the display even if the

actual instantaneous fuel consumption is

higher.

• The indication on the display may be

delayed if fuel consumption is greatly

affected by driving conditions.

• The display shows estimated values.

Indications may not be the same as

actual values.

Average fuel consumption / 5-minute

average fuel consumption

Average fuel consumption from previous

reset and 5-minute average fuel consump-

tion are shown.

(Average fuel consumption)

68PM00281

(5) Average fuel consumption

If you selected average fuel consumption

the last time you drove the vehicle, the dis-

play shows the last value of average fuel

consumption from previous driving when

the engine switch is pressed to change the

ignition mode to “ON”. Unless you reset

the value of average fuel consumption, the

display indicates the value of average fuel

consumption based on the average fuel

consumption during previous driving.

NOTE:

When you reconnect the negative (–) ter-

minal to the battery, the value of average

fuel consumption will be shown after driv-

ing for a period of time.

You can select when the value of average

fuel consumption is reset from among the

following two methods;

• Reset after refuel: the value of average

fuel consumption will be reset automati-

cally by refueling.

• Reset with trip meter A: the value of

average fuel consumption will be reset

automatically by resetting trip meter A.

To change when the value of average fuel

consumption is reset, refer to “Setting

mode” in this section.

NOTE:

If you add only a small amount of fuel

when you select “Reset after refuel”, the

average fuel consumption value may not

be reset.

(4)

EXAMPLE

(5)

EXAMPLE

2-90

BEFORE DRIVING

68PM2-01E

(5-minute average fuel consumption)

68PM00282

(6) 5-minute average fuel consumption

You can check transition of 5-minute aver-

age fuel consumption every 5 minutes

from 15 minutes before up to now. Time

indication and driving cycle indication can

be changed. For details, refer to “Setting

mode” in this section.

Driving range

68PM00283

(7) Driving range

If you selected driving range the last time

you drove the vehicle, the display indicates

“---” for a few seconds and then indicates

the current driving range when the engine

switch is pressed to change the ignition

mode to “ON”.

The driving range shown in the display is

the approximate distance you can drive

until the fuel gauge indicates “E”, based on

current driving conditions.

When the low fuel warning light comes on,

the display “---” will appear.

If the low fuel warning light comes on, fill

the fuel tank immediately regardless of the

value of driving range shown in the display.

As the driving range after refueling is cal-

culated based on the most recent driving

condition, the value is different each time

you refuel.

NOTE:

• If you refuel when the ignition mode is

“ON”, the driving range may not indicate

the correct value.

• When you reconnect the negative (–)

terminal to the battery, the value of driv-

ing range will be shown after driving for a

period of time.

Average speed / 5-minute average

speed

Average speed from previous reset and 5-

minute average speed are shown.

(Average speed)

68PM00284

(8) Average speed

(6)

EXAMPLE

(7)

EXAMPLE

(8)

EXAMPLE

2-91

BEFORE DRIVING

68PM2-01E

If you selected average speed the last time

you drove the vehicle, the display indicates

the last value of average speed from previ-

ous driving when the engine switch is

pressed to change the ignition mode to

“ON”. Unless you reset the value of aver-

age speed, the display indicates the value

of average speed which includes average

speed during previous driving.

To reset the value of average speed, push

and hold the indicator selector knob (2) for

about 2 seconds when the display indi-

cates an average speed. The display

shows “---” and then indicates a new aver-

age speed after driving for a short time.

NOTE:

When you reconnect the negative (–) ter-

minal to the battery, the value of average

speed will be shown after driving for a

period of time.

(5-minute average speed)

68PM00285

(9) 5-minute average speed

You can check transition of 5-minute aver-

age speed every 5 minutes from 10 min-

utes before up to now.

Driving time

68PM00286

(10) Driving time

Driving time from previous reset is shown.

To reset the driving time, push and hold the

indicator selector knob (2) for about 2 sec-

onds when the display indicates a driving

time. The display shows “---” and then indi-

cates a new driving time after driving for a

short time.

NOTE:

Disconnection of the battery negative (-)

terminal will reset the indication of the driv-

ing time.

(9)

EXAMPLE

(10)

EXAMPLE

2-92

BEFORE DRIVING

68PM2-01E

Clock and date

Date and time are shown. For the setting

procedure, refer to “Setting mode” in this

section.

Motion

68PM00287

The indication is used differently for the

vehicle running and stopped.

G (acceleration of gravity) position applied

to the vehicle body while driving is shown

by a globe (11).

When the vehicle is stopped, historical

data of G positions applied to the vehicle

body during the driving is shown as a

graph (12).

G position history graph at the vehicle

stopped can be changed to indicate or

hide. For details, refer to “Setting mode” in

this section.

NOTE:

• If G position history graph at the vehicle

stopped has been set in indication

mode, the graph (12) is shown for sev-

eral seconds when you change the igni-

tion mode to “LOCK” (OFF) after driving.

• The graph is shown approximately and

the actual movement may differ.

Torque and power

Present engine torque and power are

shown.

Accelerator and brake

Present accelerator pedal depressing

degree and brake line pressure are shown.

The display is selectable to indicate or not

to indicate. For details, refer to “Setting

mode” in this section.

(11) (12)

EXAMPLE

WARNING

Do not look in the display while driv-

ing. Doing so may result in an unex-

pected accident.

2-93

BEFORE DRIVING

68PM2-01E

Energy flow (if equipped)

The state of SHVS operation can be checked looking at the information display. For

details, refer to “SHVS (Smart Hybrid Vehicle by Suzuki)” in “OPERATING YOUR VEHI-

CLE”.

information display Description

68PM00288

When the vehicle is running, ISG assists engine power as

a motor

68PM00289

When the vehicle is powered by the engine

68PM00290

When decelerating your vehicle, the ISG generates elec-

tricity without engine power.

68PM00291

When the engine auto stop by the ENG A-STOP system

Information of after driving

When you press the engine switch to

change the ignition mode to “LOCK”

(OFF), the following information appears

for several seconds on the information dis-

play.

68PM00292

EXAMPLE

(if equipped)

2-94

BEFORE DRIVING

68PM2-01E

Selector position (for automatic

transaxle or CVT vehicles) / Gear-

shift indicator (if equipped)

68PM00255

Selector position

When the engine switch is pressed to

change the ignition mode to “ON”, the dis-

play (D) indicates the gear position (j).

For details on how to use the transaxle,

refer to “Using transaxle” in the “OPERAT-

ING YOUR VEHICLE” section.

Gearshift indicator

Refer to “Gearshift indicator” in the

“OPERATING YOUR VEHICLE” section.

Trip meter

The display (E) shows the trip meter.

The trip meter can be used to measure the

distance traveled on short trips or between

fuel stops.

You can use trip meter A or trip meter B

independently.

To reset the trip meter to zero, push and

hold the trip meter selector knob (3) for

about 2 seconds when the display shows

the trip meter.

Odometer

The display (F) shows the odometer.

The odometer records the total distance

the vehicle has been driven.

Setting mode

When the ignition mode is “ON” and the

vehicle is stationary, you can enter the set-

ting mode of the information display by

pushing and holding the indicator selector

knob (2) for more than 3 seconds.

• To select the setting that you want to

change, turn the indicator selector knob

(2) left or right.

• To change the setting, push the indicator

selector knob (2).

• To exit the setting mode, select “Back”

and push the indicator selector knob (2).

68PM00256

NOTE:

The currently selected setting item is sur-

rounded by a frame.

(j)

EXAMPLE

NOTICE

Keep track of your odometer reading

and check the maintenance sched-

ule regularly for required services.

Increased wear or damage to certain

parts can result from failure to per-

form required services at the proper

mileage intervals.

EXAMPLE

2-95

BEFORE DRIVING

68PM2-01E

NOTE:

• If you push and hold the indicator selec-

tor knob (2) to enter the setting mode

when the display (C) shows average fuel

consumption or average speed, the

value will be reset simultaneously. If you

do not want to reset the value, push the

indicator selector knob quickly to switch

the indication of the display.

• If you turn the ignition switch, press the

engine switch or start to move the vehi-

cle when the display is in the setting

mode, the setting mode will be canceled

automatically.

Distance unit

(Odometer / trip meter distance unit set-

ting)

You can change the units in which odome-

ter / trip meter distance is displayed.

NOTE:

When you change the units in which odom-

eter / trip meter distance is displayed, the

trip meter will be reset automatically.

Fuel economy

(Fuel consumption unit setting)

You can change the units that fuel con-

sumption is displayed in.

Language

You can change the language of the infor-

mation display.

Fuel reset (Average fuel consumption

reset setting)

You can change when the value of aver-

age fuel consumption is reset.

Temperature

(Temperature unit setting)

You can change the units that temperature

is displayed in.

NOTE:

When you change the units that tempera-

ture is displayed in, the automatic heating

and air conditioning system (if equipped)

temperature display units will be changed

automatically.

Set Sensors

(Parking sensors (if equipped) setting)

The parking sensor can be switched

between the normal mode and trailer

mode.

Clock setting

(Adjusting the clock)

• To change the hour indication, turn the

indicator selector knob (2) left or right

repeatedly when the hour indication

appears as reversed color. To change

the hour indication quickly, turn and hold

the indicator selector knob (2). To set the

hour indication, push the indicator selec-

tor knob (2) and the minute indication

appears as reversed color.

• To change the minute indication, turn the

indicator selector knob (2) left or right

repeatedly when the minute indication

appears as reversed color. To change

the minute indication quickly, turn and

hold the indicator selector knob (2). To

set the minute indication, push the indi-

cator selector knob (2).

You can also switch the time indication

between 12-hour and 24-hour format.

(Adjusting the date)

Adjust year, month, and day by operating

the indicator selector knob (2) in the same

way as the adjusting the clock.

2-96

BEFORE DRIVING

68PM2-01E

Door lock (Door lock setting)

You can choose either once or twice oper-

ation(s) to unlock all doors (including the

tailgate) or release the dead lock system (if

equipped) by turning the key, or operating

keyless push start system remote control-

ler or request switch.

You can also turn off or on the buzzer

sound when the door(s) is(are) locked or

unlocked.

Lights

(Lane change setting)

The turn signal and its indicator can be set

whether they flash three times even if you

return the turn signal control lever immedi-

ately after moving it.

Guide me light setting

(Light setting)

You can change the lighting time of “To

car” function or “To home” function.

Oil change

(Oil life monitoring system reset setting)

The oil life monitoring system must be

reset after changing the engine oil and oil

filter.

TPMS

(Tire pressure monitoring system set-

ting)

• You can check the current tire inflation

pressure on the information display.

• You can set one of the initial values of

tire pressure below that are indicated on

the tire information label.

– Comfort Mode

– Eco Mode

– Load Mode

Refer to “Tire pressure monitoring system

(TPMS)” in “OPERATING YOUR VEHI-

CLE” section for details.

IS A/C (ENG A-STOP system setting)

(if equipped)

• When using the automatic heating and

air conditioning system (if equipped),

you can select one of the following

engine auto stop settings.

– Standard

– Economy

– Comfort

• When “Economy” is selected, engine

auto stop condition is eased, compared

with “Standard”. Engine auto stop condi-

tion will occur more frequently, the stop

time will be longer, leading to reduction

of fuel consumption.

• When “Comfort” is selected, engine auto

stop condition becomes severe, com-

pared with “Standard”. Engine auto stop

condition will occur less frequently, the

stop time will be shorter, leading to more

comfortable cabin condition by air condi-

tioner.

2-97

BEFORE DRIVING

68PM2-01E

Display item

(Car color setting)

You can change the car color of the infor-

mation display.

(Calendar dis setting)

You can change the on/off of the calendar.

(Calendar form setting)

You can change the calendar form of the

information display.

(Fuel eco hist setting)

Transitional indication of average fuel con-

sumption can be switched to timed indica-

tion and driving cycle indication.

(Motion hist setting)

Indication of G position history graph at the

vehicle stopped can be selected to enable

or disable.

(Idling dsp setting)

Display of ENG A-STOP operation with

ignition mode “LOCK” (OFF) is selectable

to indicate or not to indicate.

(Pedal op dsp setting)

Display of “Accelerator and brake” is

selectable to indicate or not to indicate.

Default (initialization setting)

If you select “YES” and push the indicator

selector knob (2), all settings will be reini-

tialized.

Warning and Indicator Messages

The display shows warning and indicator

messages to let you know about certain

vehicle problems.

A tone may also sound to alert you.

If warning and indicator messages appear

on the display, follow the messages.

Master warning indicator light

68PM00278

When the display shows warning and indi-

cator messages, the master warning indi-

cator light may also blink.

NOTE:

• When the problem that causes a mes-

sage to appear is corrected, the mes-

sage will disappear.

• If a message is displayed, and other

problems requiring a message occur, the

message for each of the problems will

be alternately displayed about every 5

seconds.

• When you push and hold the indicator

selector knob (2) for about 2 seconds

while a message is displayed, the mes-

sage will disappear temporarily. If the

problem that caused the message is not

corrected, the message will appear

again after 5 seconds.

2-98

BEFORE DRIVING

68PM2-01E

Warning and indicator messages

All model

(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected.

Warning and indicator

message

Master warning

indicator light

Sound Cause and remedy

68PH02232

Blinks

(only while vehicle

is in motion)

Beep (one time from interior

buzzer; only while vehicle is

in motion)

A door or tailgate is not properly closed.

Stop the vehicle in a safe place and close

the door or tailgate properly. (#1)

68PH02233

Blinks Continuous beep (from inte-

rior buzzer)

The headlights and/or the position lights are

left on. Turn them off.

2-99

BEFORE DRIVING

68PM2-01E

(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected.

Warning and indicator

message

Master warning

indicator light

Sound Cause and remedy

68PH02234

Off Beep (one time from interior

buzzer)

Fuel is low. Refill it immediately. (#1)

68PH02235

Off Off The road may be icy. Drive very carefully.

(#1)

2-100

BEFORE DRIVING

68PM2-01E

Warning and indicator

message

Master warning

indicator light

Sound Cause and remedy

68PH02236

Blinks Beep (one time from interior

buzzer)

If this message is displayed, have your

vehicle inspected by an authorized SUZUKI

dealer.

2-101

BEFORE DRIVING

68PM2-01E

(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected.

Warning and indicator

message

Master warning

indicator light

Sound Cause and remedy

68PH02237

Off Off This message is displayed when “ACC”

position is selected as the power supply

position. (#1)

68PH02238

Off Off The brake pedal (for automatic transaxle or

CVT models) or the clutch pedal (for man-

ual transaxle models) is depressed. Press

the engine switch to start the engine.

2-102

BEFORE DRIVING

68PM2-01E

Warning and indicator

message

Master warning

indicator light

Sound Cause and remedy

68PH02239

Blinks Beep (one time from interior

buzzer)

There is a problem with the steering lock

system.

Have your vehicle inspected by an autho-

rized SUZUKI dealer.

68PH02240

Blinks Beep (one time from interior

buzzer)

There is a problem with the keyless push

start system.

Have your vehicle inspected by an autho-

rized SUZUKI dealer.

2-103

BEFORE DRIVING

68PM2-01E

Warning and indicator

message

Master warning

indicator light

Sound Cause and remedy

68PH02241

Blinks Series of beeps under cer-

tain conditions (for about 2

seconds from exterior and/or

interior buzzers)

The remote controller may be outside the

vehicle or its battery may have become dis-

charged. Locate the remote controller or

touch the engine switch with the remote

controller.

If the message still appears, replace the

remote controller battery.

68PH02242

2-104

BEFORE DRIVING

68PM2-01E

(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected.

Warning and indicator

message

Master warning

indicator light

Sound Cause and remedy

68PH02243

Off Off This message is displayed when “ON” posi-

tion is selected as the power supply posi-

tion. (#1)

68PH02244

Blinks Beep (one time from interior

buzzer)

The steering lock is not disengaged. While

lightly turning the steering wheel in both

directions, press the engine switch again.

2-105

BEFORE DRIVING

68PM2-01E

(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected.

Warning and indicator

message

Master warning

indicator light

Sound Cause and remedy

68PH02245

Blinks Beep (one time from interior

buzzer)

The remote controller battery is about to

become flat. Replace the battery. (#1)

Manual transaxle

68PH02246

Off Off The engine switch is pressed without

depressing the brake and clutch pedals. Try

again as instructed by the message.

2-106

BEFORE DRIVING

68PM2-01E

Warning and indicator

message

Master warning

indicator light

Sound Cause and remedy

Automatic transaxle or CVT

68PM00293

Off Off The engine switch is pressed with the gear-

shift lever in a position other than “P” or “N”

and/or without depressing the brake pedal.

Try again as instructed by message.

Automatic transaxle or CVT

68PM00294

Off Off The engine switch is pressed with the gear-

shift lever in a position other than “P”. Try

again as instructed by the message.

2-107

BEFORE DRIVING

68PM2-01E

Warning and indicator

message

Master warning

indicator light

Sound Cause and remedy

68PM00295

Blinks Beep (one time from interior

buzzer)

Change the engine oil and oil filter immedi-

ately.

The oil life monitoring system must be reset

after changing the engine oil and oil filter.

Refer to “Oil change request light” in this

section.

2-108

BEFORE DRIVING

68PM2-01E

CVT model

Warning and indicator

message

Master warning

indicator light

Sound Cause and remedy

68PM00296

Blinks “Beep” (one time from inte-

rior buzzer)

The CVT fluid temperature becomes too

high.

Stop the vehicle in a safe place and let the

fluid cool down.

2-109

BEFORE DRIVING

68PM2-01E

Vehicle with ESP

system

Warning and indicator

message

Master warning

indicator light

Sound Cause and remedy

68PM00297

Blinks Beep (one time from interior

buzzer)

There may be a problem with ESP

sys-

tem.

Have your vehicle inspected by an autho-

rized SUZUKI dealer.

Hill Hold Control System

68PM00298

Blinks Beep (one time from interior

buzzer)

There may be a problem with hill hold con-

trol system (if equipped).

Have your vehicle inspected by an autho-

rized SUZUKI dealer.

2-110

BEFORE DRIVING

68PM2-01E

NOTE:

• If your vehicle is equipped with the ENG A-STOP system, the information display also indicates warning and indicator messages

related to the system. For information on these messages, refer to “ENG A-STOP system (engine auto stop start system) (if

equipped)” in “OPERATING YOUR VEHICLE” section.

• If your vehicle is equipped with the radar brake support system, the information display also indicates warning and indicator messages

related to the system. For information on these messages, refer to “Radar brake support system (if equipped)” in “OPERATING YOUR

VEHICLE” section.

• If your vehicle is equipped with the adaptive cruise control system, the information display also indicates warning and indicator mes-

sages related to the system. For information on these messages, refer to “Adaptive cruise control system (if equipped)” in “OPERAT-

ING YOUR VEHICLE” section.

• If your vehicle is equipped with a parking sensor system, the information display also indicates warning and indicator messages

related to the system. For information on these messages, refer to “Parking sensors (if equipped)” in “OPERATING YOUR VEHICLE”

section.

Before Driving -> Instrument cluster (Type C) (if equipped) for Your Suzuki Baleno 4 Door First Generation (1995-2002)

Related Topics

Popular Owner Manuals

Latest Owner Manuals