Get Other Controls and Equipment Guide for Suzuki Baleno 4 Door Second Generation (2015-2021)

OTHER CONTROLS AND EQUIPMENT

68PM5002

OTHER CONTROLS AND EQUIPMENT

Fuel Filler Cap ..................................................................... 5-1

Engine Hood ........................................................................ 5-2

Sun Visor ............................................................................. 5-4

Interior Light ........................................................................ 5-5

Accessory Socket ............................................................... 5-8

AUX/USB Socket (if equipped) ........................................... 5-9

Assist Grips ......................................................................... 5-9

Glove Box ............................................................................ 5-10

Cup Holder and Storage Area ............................................ 5-11

Footrest ................................................................................ 5-13

Floor Mats (if equipped) ..................................................... 5-13

Luggage Compartment Hook ............................................. 5-14

Luggage Compartment Cover ............................................ 5-14

Frame Hooks ....................................................................... 5-15

Heating and Air Conditioning System ............................... 5-16

Manual Heating and Air Conditioning System ................. 5-19

Automatic Heating and Air Conditioning System

(Climate Control) ................................................................. 5-24

Radio Antenna ..................................................................... 5-30

Installation of Radio Frequency Transmitters .................. 5-30

Audio System (if equipped) ................................................ 5-31

5-1

OTHER CONTROLS AND EQUIPMENT

Fuel Filler Cap

68PH00501

68PH00574

The fuel filler cap is located on the left rear

side of the vehicle. The fuel filler door can

be unlocked by pulling up the opener lever

located on the outboard side of the driver’s

seat and locked by simply closing the door.

57L51093

To remove the fuel filler cap:

1) Open the fuel filler door.

2) Remove the cap by turning it counter-

clockwise.

68PH00502

NOTE:

The cap holder (1) holds the fuel filler cap

(2) by hooking the groove (3) when refuel-

ing.

To reinstall the fuel filler cap:

1) Turn the cap clockwise until you hear

several clicks.

2) Close the fuel filler door.

EXAMPLE

CAUTION

Remove the fuel filler cap slowly. The

fuel may be under pressure and may

spray out, causing injury.

Open

EXAMPLE

WARNING

Fuel is extremely flammable. Do not

smoke when refueling, and make

sure there are no open flames or

sparks in the area.

(1)

(2)

(3)

(1)

EXAMPLE

5-2

OTHER CONTROLS AND EQUIPMENT

Engine Hood

68PH00503

To open the engine hood:

1) Pull the hood release handle located on

the outboard side of the driver’s side of

the instrument panel. This will disen-

gage the engine hood lock halfway.

68PH00504

2) Push the under-hood release lever

sideways with your finger, as shown in

the illustration. While pushing the lever,

lift up the engine hood.

WARNING

If you need to replace the fuel cap,

use a MARUTI genuine cap. Use of an

improper cap can result in a malfunc-

tion of the fuel system or emission

control system. It may also result in

fuel leakage in the event of an acci-

dent.

EXAMPLE

CAUTION

The release lever can be hot enough

to burn your finger right after driving.

Touch the lever after it becomes cool

enough.

NOTICE

Make sure that the wiper arms are not

raised before you lift up the engine

hood to avoid damaging the wiper

arms and the engine hood.

EXAMPLE

5-3

OTHER CONTROLS AND EQUIPMENT

68PH00505

3) While holding the hood, pull the prop

rod out from the holding clip, then insert

the end of the rod into the designated

hole.

To close the engine hood:

1) Lift the hood up slightly and remove the

prop rod from the hole. Put the prop rod

back to the holding clip.

68PH00506

2) Lower the hood to about 20 cm above

the hood latch, then let it drop down.

Make sure the hood is securely latched

after closing.

CAUTION

• The prop rod can be hot enough to

burn your finger right after driving.

Touch the rod after it becomes cool

enough.

• Insert the end of the rod into the

hole securely. If the rod drops off,

your body may be caught in the

hood.

• The rod may drop off when the

hood is hit by a wind. Be careful on

windy days.

EXAMPLE

WARNING

Make sure the hood is fully closed

and latched before driving. If it is not,

it can fly up unexpectedly during

driving, obstructing your view and

resulting in an accident.

CAUTION

To avoid injury, be sure no part of the

occupant’s body such as hands or

head is in the path of the hood when

closing it.

NOTICE

Pressing the hood from above may

damage the hood.

5-4

OTHER CONTROLS AND EQUIPMENT

Sun Visor

68PH00507

The sun visors can be pulled down to block

glare coming through the windshield, or

they can be unhooked and turned to the

side to block glare coming through the side

window.

Card holder (if equipped)

Type1

68PH00508

Type2

68PH00509

(1) Card holder

(2) Mirror cover

You can put a card in the card holder (1) on

the back of the sun visor.

Vanity mirror (if equipped)

68PH02501

(3) Vanity mirror

(4) Vanity mirror light (if equipped)

To use the vanity mirror (3) on the back of

the sun visor, pull up the mirror cover (2).

The vanity mirror light (4) comes on when

the mirror cover (2) is opened.

NOTICE

When unhooking and hooking a sun

visor, be sure to handle it by the hard

plastic parts or the sun visor can be

damaged.

(1)

EXAMPLE

(1)

(2)

EXAMPLE

NOTICE

When you park your vehicle outdoors

in direct sunlight or in hot weather,

do not leave plastic cards in the

holder. The heat may distort them.

(4)

(3)

EXAMPLE

5-5

OTHER CONTROLS AND EQUIPMENT

Interior Light

68PH00511

(1) Glove box light (if equipped)

(2) Footwell lights (if equipped)

68PH00512

(3) Front (if equipped)

(4) Center

(5) Courtesy Lights (if equipped)

(6) Luggage compartment (if equipped)

WARNING

• Do not use the mirror while driving

your vehicle or could lose control

of the vehicle.

• When using the vanity mirror, do

not move too close to a front air

bag location or lean against it. If

the front air bag is accidentally

inflated, it could hit you hard.

NOTICE

If the vanity mirror has the light, do

not leave the mirror cover open for a

long time, or the battery will dis-

charge.

(2)(2)(1)

EXAMPLE

(3)

(4)

(5) (5)

(6)

EXAMPLE

5-6

OTHER CONTROLS AND EQUIPMENT

Glove Box Light (if equipped) (1)

Refer to “Glove Box” in this section.

Footwell Lights (if equipped) (2)

A footwell light is provided in the leg space

in front of each front seat. The light comes

on when the door is opened. After closing

all doors, the light will remain on for about

15 seconds and then fade out. If you press

the engine switch to change the ignition

mode to “ACC” or “ON” during this time,

the light will start to fade out immediately.

NOTE:

• You can change the footwell lights oper-

ation via the information display. Refer to

“Information Display” in the “BEFORE

DRIVING” section.

• If you leave any door open, the light will

automatically be turned off after about

15 minutes to prevent the battery from

discharging.

Front (if equipped) (3)

68PH00513

Push the switch to turn on the light and

push it again to turn off the light.

NOTE:

If your vehicle is equipped with the keyless

push start system or the keyless entry sys-

tem, the light will automatically be turned

off to prevent the battery from discharging

when the following conditions are simulta-

neously met:

• The ignition switch is in the “LOCK” posi-

tion, or the ignition mode is “LOCK” (OFF).

• The hazard warning lights, the position

lights and the headlights are off.

• After 15 minutes of the light on.

Center (4)

68PH00514

This light switch has three positions which

function as described below:

ON (a)

The light comes on and stays on regard-

less of whether the door is open or closed.

NOTE:

If your vehicle is equipped with the keyless

push start system or the keyless entry sys-

tem, the light will automatically be turned

off to prevent the battery from discharging

when the following conditions are simulta-

neously met:

• The ignition switch is in the “LOCK” posi-

tion, or the ignition mode is “LOCK” (OFF).

• The hazard warning lights, the position

lights and the headlights are off.

• After 15 minutes of the light on.

EXAMPLE

(a)(b)(c)

EXAMPLE

5-7

OTHER CONTROLS AND EQUIPMENT

DOOR (b)

The light comes on when the door is

opened. After closing all doors, the light

will remain on for about 15 seconds and

then fade out. If you insert the key, or press

the engine switch to change the ignition

mode to “ACC” or “ON” during this time,

the light will start to fade out immediately.

After removing the key from the ignition

switch or press the engine switch to

change the ignition mode to “LOCK”, the

light will turn on for about 15 seconds and

then fade out.

NOTE:

If you leave any door open, the light will

automatically be turned off after about 15

minutes to prevent the battery from dis-

charging.

OFF (c)

The light remains off even when the door is

opened.

Courtesy Lights (if equipped) (5)

68PH00515

Each front door has a courtesy light on its

inside bottom. It lights automatically when

the door is opened.

NOTE:

If you leave any door open, the light will

automatically be turned off after about 15

minutes to prevent the battery from dis-

charging.

Luggage Compartment

(if equipped) (6)

68PH00516

When you open the tailgate with the lug-

gage compartment light switch in the “ON”

position (1), the light comes on for about

15 minutes.

When the luggage compartment light

switch is in the “OFF” position (2), the light

remains off regardless of whether the tail-

gate is open or close.

EXAMPLE

(1) (2)

EXAMPLE

5-8

OTHER CONTROLS AND EQUIPMENT

68PH00517

NOTE:

The number of doors involved in the light-

ing operation of the interior light depends

on the vehicle specification. If there is a

switch (rubber projection) at the door

opening as shown, the door is involved in

the lighting operation. The tailgate is also

involved in this operation even without the

rubber projection.

Accessory Socket

Center console

68PH00518

Floor console

68PH00519

The accessory socket will work when the

ignition switch is in the “ACC” or “ON” posi-

tion, or the ignition mode is “ACC” or “ON”.

Each socket can be used to provide 12

volt/120 watt/10 ampere power for electri-

cal accessories when used alone. Make

sure that the cap remains on the socket

when the socket is not in use.

EXAMPLE

NOTICE

• To prevent the fuse from being

blown, when using sockets at the

same time, do not exceed the total

combined power capacity of 12

volt/120 watt/10 ampere.

• Use of inappropriate electrical

accessories can cause damage to

your vehicle’s electrical system.

Make sure that any electrical

accessories you use are designed

to plug into this type of socket.

5-9

OTHER CONTROLS AND EQUIPMENT

AUX/USB Socket (if equipped)

68PH00520

Connect your portable digital music player,

etc. to this socket to enjoy music through

the vehicle’s audio system using it as a

source. Refer to “Audio System” in this sec-

tion

Assist Grips

68PH00521

Assist grips are provided for convenience.

Coat Hooks

68PH00522

You can hang clothing on the coat hooks.

These hooks are not designed for large or

heavy items and are located with rear right

assist grip.

NOTICE

Always close the lid when not in use,

since entry of foreign material, dust,

water, conductive liquids may dam-

age the audio system or USB device.

EXAMPLE

NOTICE

To avoid damaging the assist grip

and the molded headlining, do not

hang down the assist grip.

5-10

OTHER CONTROLS AND EQUIPMENT

Glove Box

68PH00523

To open the glove box, pull the latch lever.

To close it, push the lid until it latches

securely.

68PH00524

The glove box light (if equipped) stays on

while the lid is open.

WARNING

Never drive with the glove box lid

open. It could cause injury if an acci-

dent occurs.

EXAMPLE

5-11

OTHER CONTROLS AND EQUIPMENT

Cup Holder and Storage Area

68PM5004

(1) Driver’s pocket (2) Front cup holders

(3) Front bottle holder (4) Front armrest with console box

(if equipped)

(5) Rear cup holder (if equipped) (6) Front seat back pocket (if equipped)

(7) Rear bottle holder

(1)

(2)

(3)

(4)/(5)

(6)

(7)

EXAMPLE

Driver’s Pocket (1)

WARNING

Do not place any objects which may

fall out from the pocket when the

vehicle is moving.

Failure to take the precaution may

result in an object interfering with the

pedals and causing a loss of vehicle

control or an accident.

5-12

OTHER CONTROLS AND EQUIPMENT

Front Cup Holders (2) /

Rear Cup Holder (if equipped) (5)

Front Bottle Holder (3) /

Rear Bottle Holder (7)

Always place the bottle with its cap closed

in the bottle holder.

Front Armrest with Console Box

(if equipped) (4)

Console box

Use this stowage for keeping small items.

Open the compartment by raising the top

lid while keeping the lever (1) up.

61MM0B030

NOTE:

Always close the lid after you put some-

thing into or take something out of the box.

WARNING

Failure to take the precautions listed

below could cause personal injury or

vehicle damage.

• Be careful when you are using the

cup holders to hold a cup contain-

ing hot liquid. Spilling out hot liq-

uid can cause burn injury.

• Do not use the bottle holders to

hold sharp-edged, hard, or break-

able objects. Objects in the bottle

holders may be thrown about

during a sudden stop or impact,

and could cause personal injury.

• Be careful not to spill liquid or

insert any foreign materials into the

moving part of the gearshift lever,

or any electrical components. Liq-

uid or foreign materials may dam-

age these parts.

NOTICE

To avoid damage to the armrest, do

not lean on it or allow a child to sit on

it.

(1)

(

)

EXAMPLE

5-13

OTHER CONTROLS AND EQUIPMENT

Front Seat Back Pocket

(if equipped) (6)

68PH00528

This pocket is provided for holding light

and soft things such as gloves, newspa-

pers or magazines.

Footrest

68PH00529

Use the footrest (1) as a support for your

left foot.

Floor Mats (if equipped)

68PH00530

To prevent the driver’s side floor mat from

sliding forward and possibly interfering with

the operation of the pedals, MARUTI genu-

ine floor mats are recommended.

Whenever you put the driver’s side floor

mat back in the vehicle after it has been

removed, be sure to hook the floor mat

grommets to the fasteners and position the

floor mat properly in the footwell.

When you replace the floor mats in your

vehicle with a different type such as all-

weather floor mats, we highly recommend

using MARUTI genuine floor mats for

proper fitting.

CAUTION

Do not put sharp-edged hard or

breakable objects in the pocket. If an

accident occurs, objects such as bot-

tles, cans, etc. can injure the occu-

pants in the rear seat.

EXAMPLE

(1)

EXAMPLE

5-14

OTHER CONTROLS AND EQUIPMENT

Luggage Compartment Hook

68PH00531

You can hang the shopping bag or other

suitable objects on the hook.

This hook is not designed for large or

heavy items.

Luggage Compartment Cover

68PH00532

Luggage or other cargo placed in the lug-

gage compartment is hidden from view by

a luggage compartment cover.

WARNING

Failure to take the following precau-

tions may result in the driver’s side

floor mat interfering with the pedals

and causing a loss of vehicle control

or an accident.

• Make sure that the floor mat grom-

mets are hooked to the fasteners.

• Never place additional floor mats

on top of the existing floor mat.

NOTICE

To avoid breaking the hook, do not

hang items heavier than following

weight.

Shopping hook: 2 kg (4.4 lbs)

EXAMPLE

WARNING

Do not carry items on top of the lug-

gage compartment cover, even if they

are small and light. Objects on top of

the cover could be thrown about in

an accident, causing injury, or could

obstruct the driver’s rear view.

EXAMPLE

5-15

OTHER CONTROLS AND EQUIPMENT

Frame Hooks

Front

68PH00533

The towing hook (1) is provided on the

front of the vehicle for use in emergency

situations only.

To install the hook (1), follow the procedure

below.

61MM0B039

1) Pick up the towing hook (1), jack handle

(A) and wheel brace (B) that are stowed

in the luggage compartment.

68PH00534

2) Remove the cover (C) by using a jack

handle (A) covered with a soft cloth as

shown in the illustration.

68PH00535

3) Install the towing hook (1) by hand.

(1)

EXAMPLE

(1)

(A)

(B)

(

)

(

)

(

)

EXAMPLE

(A)

(C)

EXAMPLE

(1)

EXAMPLE

5-16

OTHER CONTROLS AND EQUIPMENT

68PH00536

4) To tighten the towing hook (1), turn it

clockwise by using a wheel brace (B)

until the hook (1) is securely installed.

To remove the towing hook (1), reverse the

procedure used to install the towing hook.

Rear

68PH00537

The frame hook (2) is provided on the rear

of the vehicle.

To tow your vehicle on the road or high-

way, follow the instruction of “Towing” in

“EMERGENCY SERVICE” section.

Heating and Air Conditioning

System

There are two of heating and air condition-

ing systems as follows:

• Manual Heating and Air Conditioning

System

• Automatic Heating and Air Conditioning

System (Climate Control)

WARNING

Use extreme caution when you use

the towing hook (1). Avoid pulling the

vehicle to get out of severe snowy,

muddy or sandy conditions, sudden

starts or erratic driving maneuvers

which would give excessive stress

on the towing hook. The towing hook

or vehicle body may break and cause

serious injury or damage.

(1)

(B)

EXAMPLE

WARNING

Use extreme caution when you use

the frame hook (2). Avoid towing the

vehicle heavier than your vehicle,

pulling the vehicle to get out out of

severe snowy, muddy or sandy con-

ditions, sudden starts or erratic driv-

ing maneuvers which would give

excessive stress on the frame hook.

The towing hooks or vehicle body

may break and cause serious injury

or damage.

(2)

EXAMPLE

5-17

OTHER CONTROLS AND EQUIPMENT

Air Outlet

68PH00538

(1)

(2)

(5)

(3)

(4)

EXAMPLE

(1) Windshield defroster outlet

(2) Side defroster outlet

(3) Side outlet

(4) Center outlet

(5) Floor outlet

5-18

OTHER CONTROLS AND EQUIPMENT

Center outlet

68PH00539

Move the knob (1) vertically or horizontally, to adjust the direction of airflow as desired.

(1)(1)

Side outlet

68PH00540

Move the knob (1) vertically or horizontally,

to adjust the direction of airflow as desired.

The side outlet opens when you turn the

dial (2) upward and closes when you turn it

downward.

(1)(2)

5-19

OTHER CONTROLS AND EQUIPMENT

Manual Heating and Air

Conditioning System

Description of Controls

68PH02502

Temperature selector (1)

This is used to select the temperature by

turning the selector.

Blower speed selector (2)

This is used to turn on the blower and to

select blower speed by turning the selec-

tor.

Air flow selector (3)

68PH00542

This is used to select one of the functions

described below.

Ventilation (a)

68PH00543

Temperature-controlled air comes out of

the center and side outlets.

Bi-level (b)

68PH00544

Temperature-controlled air comes out of

the floor outlets and cooler air comes out

of the center and side outlets. When the

temperature selector (1) is in the fully

COLD position or fully HOT position, how-

ever, the air from the floor outlets and the

air from the center and side outlets will be

the same temperature.

(1) (2) (3)

(4) (5)

(

)

(

)

(

)

(

)

(

)

(a)

(b)

(c)

(d)

(e)

5-20

OTHER CONTROLS AND EQUIPMENT

Heat (c)

68PH00545

Temperature-controlled air comes out of

the floor outlets and the side outlets, also

comes out of the windshield defroster out-

lets and also comes slightly out of the side

defroster outlets.

Heat & defrost (d)

68PH00546

Temperature-controlled air comes out of

the floor outlets, the windshield defroster

outlets, the side defroster outlets and the

side outlets.

Defrost (e)

68PH00547

Temperature-controlled air comes out of

the windshield defroster outlets, the side

defroster outlets and the side outlets.

5-21

OTHER CONTROLS AND EQUIPMENT

Air intake selector (4)

68PH00548

This selector is used to select the following

modes.

Fresh Air (f)

When this mode is selected, the indicator

light will go off and outside air is used.

Recirculated Air (g)

When this mode is selected, the indicator

light will come on, outside air is shut out

and inside air is recirculated. This mode is

suitable when driving through dusty or pol-

luted air such as in a tunnel, or when

attempting to quickly cool down the inte-

rior.

“FRESH AIR” and “RECIRCULATED AIR”

are switched alternately each time the air

intake selector is pushed.

NOTE:

If you select “RECIRCULATED AIR” for an

extended period of time, the air in the vehi-

cle can become contaminated. Therefore,

you should occasionally select “FRESH

AIR”.

Air conditioning switch (5)

To turn on the air conditioning system, set

the blower speed selector to a position

other than off and push in the “A/C” switch.

With this “A/C” switch operation, a indica-

tor light will come on when the air condi-

tioning system is on. To turn off the air

conditioning system, push the “A/C” switch

again.

During operation of the air conditioner, you

may notice slight changes in engine

speed. These changes are normal, the

system is designed so that the compressor

turns on or off to maintain the desired tem-

perature.

Less operation of the compressor results

in better fuel economy.

System Operating Instructions

Natural ventilation

Select “VENTILATION” and “FRESH AIR”,

the temperature selector to the desired

temperature position, and the blower

speed selector to off. Fresh air will flow

through the vehicle during driving.

Forced ventilation

The control settings are the same as for

natural ventilation except you set the

blower speed selector to a position other

than off.

Normal heating (using outside air)

Select “HEAT” and “FRESH AIR”, the tem-

perature selector to the desired tempera-

ture position and the blower speed selector

to the desired blower speed position. Set-

ting the blower speed selector to a higher

blower speed position increases heating

efficiency.

Quick heating (using recirculated air)

The control settings are the same as for

normal heating except you select “RECIR-

CULATED AIR”. If you use this heating

method for an extended period of time, the

air in the vehicle can become contami-

nated and the windows can become misty.

Therefore, use this method only for quick

heating and change to the normal heating

method as soon as possible.

(f) (g)

5-22

OTHER CONTROLS AND EQUIPMENT

Head cooled/Feet warmed heating

Select “BI-LEVEL” and “FRESH AIR”, the

temperature selector to the desired tem-

perature position, and the blower speed

selector to the desired blower speed posi-

tion. Unless the temperature selector is in

the fully COLD position or fully HOT posi-

tion, the air that comes out of the center

and side outlets will be cooler than the air

that comes out of the floor outlets.

Normal cooling

Set the air flow selector to “VENTILATION”,

the temperature selector to the desired tem-

perature position and the blower speed

selector to the desired blower speed posi-

tion, and turn on the “A/C” switch. Setting

the blower speed selector to a higher

blower speed position increases cooling

efficiency.

You can switch the air intake selector to

either “FRESH AIR” or “RECIRCULATED

AIR” as you desire. Choosing “RECIRCU-

LATED AIR” increases cooling efficiency.

Quick cooling (using recirculated air)

The control settings are the same as for

normal cooling except you select “RECIR-

CULATED AIR” and the highest blower

speed.

NOTE:

• If you select “RECIRCULATED AIR” for

an extended period of time, the air in the

vehicle can become contaminated.

Therefore, you should occasionally

select “FRESH AIR”.

• If your vehicle has been left in the sun

with the windows closed, it will cool

faster if you open the windows briefly

while you operate the air conditioner with

the air intake selector at “FRESH AIR”

and the blower at high speed.

Dehumidifying

Set the air flow selector to a desired air

flow selector position, the temperature

selector to the desired temperature posi-

tion and the blower speed selector to the

desired blower speed position. Also select

“FRESH AIR” and turn on the “A/C” switch.

NOTE:

Because the air conditioner dehumidifies

the air, turning it on will help keep the win-

dows clear, even when blowing heated air

using the “DEFROST” or “HEAT &

DEFROST” functions.

68PH00549

NOTE:

If you need maximum defrosting:

• select “DEFROST” and “FRESH AIR”,

• set the blower speed selector to HIGH,

• adjust the temperature selector to the

HOT end,

• turn on the “A/C” switch, and

• adjust the side outlets so the air blows

on the side windows.

EXAMPLE

5-23

OTHER CONTROLS AND EQUIPMENT

Maintenance

If you do not use the air conditioner for a

long period, such as during winter, it may

not give the best performance when you

start using it again. To help maintain opti-

mum performance and durability of your air

conditioner, it needs to be run periodically.

Operate the air conditioner at least once a

month for one minute with the engine

idling. This circulates the refrigerant and oil

and helps protect the internal components.

If your air conditioner is equipped with air

filters, clean or replace them as specified

in the “Maintenance Schedule” in the

“INSPECTION AND MAINTENANCE” sec-

tion.

NOTE:

Your vehicle uses the air conditioning

refrigerant HFC-134a, commonly called

“R-134a”. R-134a replaced R-12 around

1993 for automotive applications. Other

refrigerants are available, including recy-

cled R-12, but only R-134a should be used

in your vehicle.

NOTICE

Using the wrong refrigerant may

damage your air conditioning sys-

tem. Use R-134a only. Do not mix or

replace the R-134a with other refrig-

erants.

5-24

OTHER CONTROLS AND EQUIPMENT

Automatic Heating and Air Conditioning System

(Climate Control)

Description of Controls

68PH00550

(1)(2)

(3)(4)

(5)

(6) (7)(8)

(9)

(1) Temperature selector

(2) Blower speed selector

(3) Air intake selector

(4) Air flow selector

(5) Defrost switch

(6) Air conditioning switch

(7) “OFF” switch

(8) “AUTO” switch

(9) Display

5-25

OTHER CONTROLS AND EQUIPMENT

Temperature selector (1)

68PH00551

Push the temperature selector (1) to adjust

the temperature.

Blower speed selector (2)

68PH00552

Air flows out at a higher rate when you

press the upper switch and at a lower rate

when you press the lower switch.

If the “AUTO” switch (8) is pushed, the

blower speed will vary automatically as the

climate control system maintains the

selected temperature.

Air intake selector (3)

68PH00553

Push the air intake selector (3) to change

between the following modes.

If the “AUTO” switch (8) is pushed, the air

intake will vary automatically as the climate

control system maintains the selected tem-

perature.

NOTE:

When you select the recirculated air mode,

the automatic operation system is deacti-

vated if you push the “AUTO” switch (8).

RECIRCULATED AIR (a)

When this mode is selected, outside air is

shut off and inside air is recirculated. This

mode is suitable when driving through an

area with polluted air such as a tunnel, or

when attempting to quickly cool down the

vehicle.

(1)

(2)

(3)(a)

(b)

5-26

OTHER CONTROLS AND EQUIPMENT

FRESH AIR (b)

When this mode is selected, outside air is

introduced.

“FRESH AIR” and “RECIRCULATED AIR”

are selected alternately each time the air

intake selector is pushed.

NOTE:

If you select “RECIRCULATED AIR” for an

extended period of time, the air in the vehi-

cle can become contaminated. Therefore,

you should occasionally select “FRESH

AIR”.

Air flow selector (4)

68PH00554

Push the air flow selector (4) to change

among the following functions. The indica-

tion of the selected mode appears on the

display.

If the “AUTO” switch (8) is pushed, the air

flow will vary automatically as the climate

control system maintains the selected tem-

perature.

Ventilation (c)

68PH00543

Temperature-controlled air comes out of

the center and side outlets.

Bi-level (d)

68PH00544

Temperature-controlled air comes out of

the floor outlets and cooler air comes out

of the center and side outlets. When the

temperature selector (1) is in the fully

COLD position or fully HOT position, how-

ever, the air from the floor outlets and the

air from the center and side outlets will be

the same temperature.

(4)

(c)

(d)

(e)

(f)

5-27

OTHER CONTROLS AND EQUIPMENT

Heat (e)

68PH00545

Temperature-controlled air comes out of

the floor outlets and the side outlets, a

small amount of air comes out of the wind-

shield defroster outlets and also comes

slightly out of the side defroster outlets.

Heat & defrost (f)

68PH00546

Temperature-controlled air comes out of

the floor outlets, the windshield defroster

outlets, the side defroster outlets and the

side outlets.

Defrost switch (5)

68PH00555

Push the defrost switch (5) to turn on the

defroster.

(5)

5-28

OTHER CONTROLS AND EQUIPMENT

Defrost

68PH00547

Temperature-controlled air comes out of

the windshield defroster outlets, the side

defroster outlets and the side outlets.

NOTE:

When the defrost switch (5) is pushed to

turn on the defroster, the air conditioning

system will come on and the “FRESH AIR”

mode will be selected automatically. In

very cold weather, however, the air condi-

tioning system will not turn on.

Air conditioning switch (6)

68PH00556

The air conditioning switch (6) is used to

turn on and off the air conditioning system

only when the blower is on. To turn on the

air conditioning system, push in the switch

and “A/C” will appear on the display. To

turn off the air conditioning system, push in

the switch again and “A/C” will go off.

System Operating Instructions

Automatic operation

68PH00557

You can let the climate control system work

automatically. To set the system for fully-auto-

matic operation, follow the procedure below.

1) Start the engine.

2) Push the “AUTO” switch (8).

3) Set the desired temperature by turning

the temperature selector (1).

The blower speed, air intake and air flow are

controlled automatically to maintain the set

temperature. However, the air flow is not

changed to the “Defrost” position automatically.

NOTE:

When you select the recirculated air mode,

the automatic operation system is deacti-

vated if you push the “AUTO” switch (8).

(6)

(1)(6) (7)(8)

5-29

OTHER CONTROLS AND EQUIPMENT

You can use the air conditioning switch (6)

to manually turn the air conditioner on or off

according to your preference. When you

turn the air conditioning switch off, the cli-

mate control system cannot lower the

inside temperature below outside tempera-

ture.

To turn the climate control system off, push

the “OFF” switch (7).

NOTE:

If the “AUTO” on the display blinks, there is

a problem in the heating system and/or air

conditioning system. You should have the

system inspected by an authorised Maruti

Suzuki workshop.

NOTE:

• To find the temperature at which you are

most comfortable, start with the 25°C

(75°F) setting.

• If you turn the temperature selector (1)

until “HI” or “LO” appears on the display,

the climate control system will operate at

maximum heating or cooling and the

blower will run at full speed.

• To avoid blowing cold air in cold weather

or hot air in hot weather, the system will

delay turning on the blower until warmed

or chilled air is available.

• If your vehicle has been left in the sun

with the windows closed, it will cool

faster if you open the windows briefly.

• Even under the automatic operation, you

can set individual selectors to the man-

ual mode. The manually selected func-

tions are maintained, and the other

functions remain under automatic opera-

tion.

• If the windshield and/or the front door

windows are fogged, push the defrost

switch (5) to turn on the defroster, or

push the air flow selector (4) to change

the air flow to the “Heat & defrost” posi-

tion to defog the windows.

• To return the blower speed selector (2),

air intake selector (3), and air flow selec-

tor (4) to automatic operation, push the

“AUTO” switch (8).

68PH00558

Be careful not to cover the interior tem-

perature sensor (10) located between the

steering wheel and the climate control

panel, or the solar sensor (11) located at

the top of the driver’s side dashboard.

These sensors are used by the automatic

system to regulate temperature.

Manual operation

You can manually control the climate con-

trol system. Set the selectors to the

desired positions.

68PH00549

NOTE:

If you need maximum defrosting:

• push the defrost switch (5) to turn on the

defroster (the air conditioning system will

come on and the “FRESH AIR” mode will

be selected automatically),

• set the blower speed selector to HIGH,

• adjust the temperature selector to the

“HI” indication on the display, and

• adjust the side outlets so the air blows

on the side windows.

(10)

(11)

EXAMPLE

5-30

OTHER CONTROLS AND EQUIPMENT

Maintenance

If you do not use the air conditioner for a

long period, such as during winter, it may

not give the best performance when you

start using it again. To help maintain opti-

mum performance and durability of your air

conditioner, it needs to be run periodically.

Operate the air conditioner at least once a

month for one minute with the engine

idling. This circulates the refrigerant and oil

and helps protect the internal components.

If your air conditioner is equipped with air

filters. Clean or replace them as specified

in the “Maintenance Schedule” in the

“INSPECTION AND MAINTENANCE”

section. Have this job done by your autho-

rised Maruti Suzuki workshop as the lower

glove box must be lowered for this job.

NOTE:

Your vehicle uses the air conditioning

refrigerant HFC-134a, commonly called

“R-134a”. R-134a replaced R-12 around

1993 for automotive applications. Other

refrigerants are available, including recy-

cled R-12, but only R-134a should be used

in your vehicle.

Radio Antenna

68PH00559

The radio antenna on the roof is remov-

able. To remove the antenna, turn it coun-

terclockwise. To reinstall the antenna, turn

it clockwise firmly by hand.

Installation of Radio

Frequency Transmitters

We recommend that you always ask a

authorised Maruti Suzuki workshop about

frequency band, max output power,

antenna position at vehicle and specific

conditions for installation and/or use before

installing a radio transmitter in your vehi-

cle. Such equipments may cause the elec-

tronic control system to malfunction if they

are incorrectly installed or they are not

suited for the vehicle.

NOTICE

Using the wrong refrigerant may

damage your air conditioning sys-

tem. Use R-134a only. Do not mix or

replace the R-134a with other refrig-

erants.

NOTICE

To avoid damage to the radio

antenna:

• Remove the antenna when using an

automatic car wash.

• Remove the antenna when the

antenna hits anything such as a

low ceiling in a parking garage or

putting a car cover over your vehi-

cle.

EXAMPLE

5-31

OTHER CONTROLS AND EQUIPMENT

Audio System (if equipped)

AM/FM CD PLAYER

68PH00575

NOTE:

For vehicle equipped with SMARTPLAY INFOTAINMENT SYSTEM, refer to audio manual available with the vehicle.

5-32

OTHER CONTROLS AND EQUIPMENT

Safety Information Notes on Discs

Precautions

• When the inside of the vehicle is very

cold and the player is used soon after

switching on the heater, condensation

may form on the disc or the optical parts

of the player and proper playback may

not be possible. If condensation forms

on the disc, wipe it off with a soft cloth. If

condensation forms on the optical parts

of the player, do not use the player for

about one hour. This will allow the con-

densation to disappear normally.

• Driving on extremely bumpy roads which

cause severe vibrations may cause

sound to skip.

• This unit uses a precision mechanism.

Even in the event that trouble arises,

never open the case, disassemble the

unit, or lubricate the rotating parts.

Please bring the unit to an authorised

Maruti Suzuki workshop.

Cautions on Handling

52D274

This unit has been designed specifically for

playback of compact discs bearing mark

(A) shown above.

No other discs can be played.

52D275

To remove the compact disc from its stor-

age case, press down on the center of the

case and lift the disc out, holding it care-

fully by the edges.

Always handle the compact disc by the

edges.

Never touch the surface.

WARNING

If you pay extended attention to oper-

ating the audio system or viewing the

audio system display while driving,

an accident can occur. If you set the

sound volume too loud, it could pre-

vent you from being aware of road

and traffic conditions.

• Keep your eyes on the road and

your mind on the drive. Avoid pay-

ing extended attention to operating

the audio system or viewing the

audio system display.

• Familiarize yourself with the audio

system controls and operation of

the audio system before driving.

• Preset your favorite radio stations

before driving so that you can

quickly tune to them using the pre-

sets.

• Set the sound volume to a level

that will allow you to continue to be

aware of road and traffic conditions

while driving.

(A)

(

)

Removing the disc

Proper way to hold

the compact disc

5-33

OTHER CONTROLS AND EQUIPMENT

52D347

To remove fingermarks and dust, use a

soft cloth, and wipe in a straight line from

the center of the compact disc to the cir-

cumference.

52D277

New discs may have some roughness

around the edges. The unit may not work

or the sound may skip if such discs are

used. Use a ball-point pen (B), etc. to

remove the roughness (C) from the edges

of the disc before inserting it into the unit.

52D348

Never stick labels on the surface of the

compact disc or write on the surface with a

pencil or pen.

52D349

Do not use any solvents such as commer-

cially available cleaners, anti-static spray,

or thinner to clean compact discs.

52D350

Do not use compact discs that have large

scratches, are misshaped, or cracked, etc.

Use of such discs will cause damage or

prevent the system from operating prop-

erly.

52D351

Do not expose compact discs to direct sun-

light or any heat source.

NOTE:

• Do not use commercially available CD

protection sheets or discs equipped with

stabilizers, etc.

These may get caught in the internal

mechanism and damage the disc.

• It may be impossible to play CD-R discs

with this unit due to the recording condi-

tions.

• CD-RW discs cannot be played with this

unit.

(B)

(C)

(

)

(

)

(C)

5-34

OTHER CONTROLS AND EQUIPMENT

The Bluetooth

word mark and logo are

registered trademarks and are owned by

the Bluetooth SIG, Ink.

Stop using this unit and a Bluetooth

ready device whenever requested.

This unit shares the communication fre-

quency with other private or public wireless

communication equipment such as a wire-

less LAN and other wireless communica-

tion radios.

You should stop using this unit whenever

you are notified that your unit disturbs

other wireless communication immediately.

WARNING

This is a class I laser product. Use of

controls or adjustments or perfor-

mance of procedures other than

those specified herein may result in

hazardous radiation exposure.

Do not open covers and do not

attempt to repair this unit by yourself.

Refer servicing to qualified person-

nel.

5-35

OTHER CONTROLS AND EQUIPMENT

Basic Operations

68PH00560

(1) VOL PUSH POWER knob

(2) TUNE FOLDER PUSH SOUND knob

(1)

(2)

Turning power on/off

Press the VOL PUSH POWER knob (1).

The unit starts in the function mode it was

in when the power was turned off last.

Adjusting the volume

Turn the VOL PUSH POWER knob (1).

Turning it clockwise increases the volume;

turning it counterclockwise decreases the

volume.

NOTE:

While driving, adjust the volume to an

extent that sound and/or noise coming

from outside the vehicle can be heard.

5-36

OTHER CONTROLS AND EQUIPMENT

Adjusting bass/treble/balance /fader

1) Press the TUNE FOLDER PUSH

SOUND knob (2).

Each time the knob is pressed, sound

adjustment will change as follows:

2) Turn the TUNE FOLDER PUSH

SOUND knob (2) to adjust the sound.

Adjusting the AVC (Auto volume con-

trol)

The Auto Volume Control (AVC) function

automatically adjusts (increases/

decreases) the sound volume in accor-

dance with vehicle speed. The AVC control

is provided with three selectable levels

(LEVEL OFF, 1, 2, 3). The range of volume

adjustment increases together with the

LEVEL number.

1) Press the TUNE FOLDER PUSH

SOUND knob (2) until the AVC adjust-

ment mode is selected.

2) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select the desired

AVC adjustment level. (Initial setting:

LEVEL 2)

Preset-EQ

Preset-EQ calls up various sound types in

accordance with the listening music type.

1) Press the TUNE FOLDER PUSH

SOUND knob (2) several times until

“PRESET-EQ” appears.

2) Turn the TUNE FOLDER PUSH

SOUND knob (2).

Each time the knob is turned, preset

EQ mode will change as follows:

Preset-EQ (EQ OFF)

Bass adjustment (BASS 0)

Treble adjustment (TREBLE 0)

Balance adjustment (BALANCE 0)

Fader adjustment (FADER 0)

AVC adjustment (AVC LEVEL 2)

OFF (FLAT)

JAZZ

ROCK

POP

CLASSIC

HIP-HOP

5-37

OTHER CONTROLS AND EQUIPMENT

Listening to the Radio

68PH00561

(7)

(1)

(2)

(5)

(4)

(3)

(6)

Display

(1) FM button

(2) AM button

(3) Up button

(4) Down button

(5) TUNE FOLDER PUSH SOUND knob

(6) Preset buttons ([1] to [6])

(7) AS button

(A) Band

(B) Frequency

(A)

(B)

5-38

OTHER CONTROLS AND EQUIPMENT

Selecting the FM band

Press the FM button (1).

Each time the button is pressed, the recep-

tion band will change as follows:

Selecting the AM band

Press the AM button (2).

Seek tuning

Press the seek Up button (3) or the seek

Down button (4).

The unit stops searching for a station at a

frequency where a broadcast station is

available.

Manual tuning

Turn the TUNE FOLDER PUSH SOUND

knob (5).

The frequency being received is displayed.

Preset memory

1) Select the desired station.

2) Hold down a desired button ([1] to [6])

of the Preset buttons (6) to which you

want to store the station for 2 seconds

or longer.

Auto store

Hold down the AS button (7) for 2 seconds

or longer.

Six stations in good reception will automat-

ically be stored to the Preset buttons (6) in

order, starting from a station whose fre-

quency is the lowest.

NOTE:

• Auto store can be released by pressing

AS button (7) while auto store is under

way.

• When the auto store is performed, the

station previously stored in the memory

at the position is overwritten.

• When there are fewer than 6 stations

that can be stored even if 1 round of

auto store operation is performed, no

station will be stored at the remaining

Preset buttons (6).

• 6 stations can be preset for FM1 and

FM2 in common, and 6 stations for AM

in auto store mode.

Auto store mode on/off

Press the AS button (7).

Each time the button is pressed, the mode

is switched as follows:

Radio Reception

Radio reception can be affected by envi-

ronment, atmospheric conditions, or radio

signal’s power and distance from the sta-

tion. Nearby mountains and buildings may

interfere or deflect radio reception, causing

poor reception. Poor reception or radio

static can also be caused by electric cur-

rent from overhead wires or high voltage

power lines.

FM1 FM2

AS mode on AS mode off

5-39

OTHER CONTROLS AND EQUIPMENT

Listening to a CD

68PH00562

(8)

(6)

(5)

(4)

(2)

(7)

(3)

(1)

Display

(1) Insertion slot

(2) Eject button

(3) CD button

(4) Up button

(5) Down button

(6) RPT button

(7) RDM button

(8) DISP button

(A) Track number

(B) Play time

NOTE:

This product does not support 8 cm CD

(sometimes called as “mini single CD”, “3-

inch CD”, “CD3”, etc.).

(B)

(A)

5-40

OTHER CONTROLS AND EQUIPMENT

52D274

• CDs or CD-ROMs carrying no mark (A)

cannot be used.

• Some discs recorded in CD-R/CD-RW

format may sometimes be impossible to

use.

52D291

• A CD is to be inserted with its label side

up.

• When there is a CD already in the unit, it

is impossible to insert another CD with-

out ejecting the CD in the unit. Do not

use force to insert a CD into the CD

insertion slot.

Loading a CD

Insert a CD in the Insertion slot (1).

When a CD is loaded, It begins to play.

Ejecting a CD

Press the Eject button (2).

When the ignition mode is “LOCK”, the CD

remained ejected for around 15 seconds or

longer will automatically be drawn inside

the unit. (Auto reload function)

The backup eject function:

This function allows you to eject a CD by

pressing the Eject button (2) even when

the ignition mode is off.

Listening to a CD

When a CD is inserted, playback will auto-

matically start.

When a CD is already inside the unit,

press the CD button (3) to start playback.

Selecting a track

• Press the Up button (4) to listen to the

next track.

• Press the Down button (5) twice to listen

to the previous track.

When the Down button (5) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/Rewinding a track

• Hold down the Up button (4) to fast for-

ward the track.

• Hold down the Down button (5) to fast

rewind the track.

(A)

(

)

NOTICE

• Never insert your finger or hand

into the CD insertion slot. Never

insert foreign objects.

• Never insert a CD with glue coming

out from adhesive tape or a rental

CD label or with a trace indicating

that adhesive tape or a rental CD

label has been removed. This may

cause the CD not to eject or result

in a malfunction.

NOTICE

If you forcefully try to push an

ejected CD inside the unit before auto

reloading, the disc surface might be

scratched.

When reloading a CD, remove it from

the unit completely before reloading.

5-41

OTHER CONTROLS AND EQUIPMENT

Random playback

Press the RDM button (7).

Each time the button is pressed, the mode

will change as follows:

• TRACK RANDOM

The random indicator “RDM” will light.

The tracks in the loaded disc will be

played in random order.

Repeat playback

Press the RPT button (6).

Each time the button is pressed, the mode

will change as follows:

• TRACK REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

Display change

Press the DISP button (8).

Each time the button is pressed, display

will change as follows:

NOTE:

• “NO TITLE” will be displayed when there

is no text information in the disc currently

being played.

• If text data contains more than 16 char-

acters, the “>” mark will appear at the

right end. Holding down the DISP button

(8) for 1 second or longer can display the

next page.

OFF TRACK RANDOM

OFF TRACK REPEAT

Play time

Disc title

Track title

5-42

OTHER CONTROLS AND EQUIPMENT

Listening to an MP3/WMA/AAC Disc

68PH00563

(6)

(4)

(3)

(1)

(2)

(5)

Display

(1) TUNE FOLDER PUSH SOUND knob

(2) Up button

(3) Down button

(4) RPT button

(5) RDM button

(6) DISP button

(A) Folder number

(B) Track number

(D) DISC type

(C)

(B)(A)

(D)

5-43

OTHER CONTROLS AND EQUIPMENT

Selecting a folder

Turn the TUNE FOLDER PUSH SOUND

knob (1) to select a folder.

Selecting a track

• Press the Up button (2) to listen to the

next track.

• Press the Down button (3) twice to listen

to the previous track.

When the Down button (3) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/Rewinding a track

• Hold down the Up button (2) to fast for-

ward the track.

• Hold down the Down button (3) to fast

rewind the track.

Random playback

Press the RDM button (5).

Each time the button is pressed, the mode

will change as follows:

• FOLDER RANDOM

The random indicator “F.RDM” will light.

The tracks in the current folder will be

played in random order.

• ALL RANDOM

The random indicator “RDM” will light.

The tracks in the loaded disc will be

played in random order.

Repeat playback

Press the RPT button (4).

Each time the button is pressed, the mode

will change as follows:

• FILE REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

• FOLDER REPEAT

The repeat indicator “F.RPT” will light.

All tracks in the currently selected folder

will be played repeatedly.

OFF FOLDER RANDOM ALL RANDOM

OFF FILE REPEAT FOLDER REPEAT

5-44

OTHER CONTROLS AND EQUIPMENT

Display change

Press the DISP button (6).

Each time the button is pressed, display

will change as follows:

NOTE:

• “NO TITLE” will be displayed when there

is no text information in the disc currently

being played.

• If text data contains more than 16 char-

acters, the “>” mark will appear at the

right end. Holding down the DISP button

(6) for 1 second or longer can display the

next page.

Notes on MP3/WMA/AAC

What is MP3?

• MP3 (MPEG audio layer3) is an audio

compression format that has become

the standard format among PC users. Its

merit is that the original audio data is

compressed to approximately 1/10 and

high sound quality is maintained. This

means that it is possible to store the data

of approximately 10 music CDs on a sin-

gle CD-R/RW disc, which in turn makes

it possible to play music for a long time

without having to change the disc.

What is WMA?

• An abbreviation of “Windows Media

Audio,” WMA is an audio compression

format developed by Microsoft.

• WMA files for which the DRM (Digital

Rights Management) function is ON can-

not be played.

• Windows Media

and the Windows

logo are trademarks or registered trade-

marks of Microsoft Corporation in the

United States and other countries.

What is AAC?

• An abbreviation of “Advanced Audio

Coding,” AAC is an audio compression

format used by MPEG2 and MPEG4.

Points to remember when making MP3/

WMA/AAC files

Common

• High bit rate and high sampling fre-

quency are recommended for high qual-

ity sounds.

• Selecting VBR (Variable Bit Rate) is not

recommended. Selecting VBR may

cause display of incorrect playing time

and jumpiness of playback.

• Playback sound quality varies depend-

ing on the encoding environment. For

details, refer to the user manual of the

encoding software and the writing soft-

ware in use.

Recording MP3/WMA/AAC files on a CD

media

• It is recommended not to write both CD-

DA files and MP3/WMA/AAC files on a

disc.

• If both CD-DA files and MP3/WMA/AAC

files are on the same disc, tracks may

not be played in the correct order or

some tracks may not be played at all.

Play time

Folder name

File name

Album name (MP3, AAC only)

Track title

Artist name

NOTICE

Never assign the “.mp3”, “.wma”, or

“.m4a” file name extension to a file if

it is not in the MP3/WMA/AAC format

file. Failure to observe this may result

in damage to the speaker due to

noise production.

5-45

OTHER CONTROLS AND EQUIPMENT

• When storing both MP3 data and WMA

data on the same disc, sort and place

them in different folders.

• Do not write files other than MP3/WMA/

AAC files and unnecessary folders on a

disc.

• MP3/WMA/AAC files should be named

to meet the standards and the file sys-

tem specifications as shown below.

• The file extension “.mp3”, “.wma” or

“.m4a” should be assigned to files based

on their format independently.

• You may encounter a trouble in playing

MP3/WMA/AAC files or displaying infor-

mation of MP3/WMA/AAC files depend-

ing on the writing software or CD

recorder in use.

• This unit does not have a play list func-

tion.

• It is recommended to write discs in Disc-

at-Once mode even though Multi-ses-

sion mode is supported.

Compression formats

MP3

• Bit rate

MPEG1 Audio Layer III: 32 k - 320 kbps

MPEG2 Audio Layer III: 8 k - 160 kbps

MPEG2.5 Audio Layer III: 8 k - 160 kbps

• Sampling frequency

MPEG1 Audio Layer III: 32 k/44.1 k/

48 kHz

MPEG2 Audio Layer III: 16 k/22.05 k/

24 kHz

MPEG2.5 Audio Layer III: 8 k/11.025 k/

12 kHz

WMA (Ver. 7, Ver. 8, Ver. 9*)

• Bit rate: CBR 32 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* WMA 9 Professional/LossLess/Voice are

not supported.

AAC*

• Bit rate: ABR 16 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* Apple Lossless is not supported.

Supported file systems

ISO 9660 Level 1/Level 2, Joliet, Romeo

Maximum number of files/folders

• Maximum number of files: 512

• Maximum number of files in a folder: 255

• Maximum depth of tree structure: 8

• Maximum number of folders: 255

(Root folder is included.)

5-46

OTHER CONTROLS AND EQUIPMENT

Listening to files stored in a USB device

68PH00560

(6)

(1)

(7)

(5)

(4)

(2)

(3)

Display

(1) MEDIA button

(2) TUNE FOLDER PUSH SOUND knob

(3) Up button

(4) Down button

(5) RPT button

(6) RDM button

(7) DISP button

(A) Folder number

(B) Track number

(D) File type

NOTICE

Do not connect any USB device other

than a USB memory or a USB audio

player. Do not connect multiple USB

devices to the USB connector using a

USB hub, etc. Supplying power to

multiple USB devices from the con-

nector could cause overheating and

smoking.

(C)

(B)(A)

(D)

5-47

OTHER CONTROLS AND EQUIPMENT

Selecting a USB device mode

Press the MEDIA button (1).

Each time the button is pressed, the mode

will change as follows:

Selecting a folder

Turn the TUNE FOLDER PUSH SOUND

knob (2) to select the desired folder.

Selecting a track

• Press the Up button (3) to listen to the

next track.

• Press the Down button (4) twice to listen

to the previous track.

When the Down button (4) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/Rewinding a track

• Hold down the Up button (3) to fast for-

ward the track.

• Hold down the Down button (4) to fast

rewind the track.

Random playback

Press the RDM button (6).

Each time the button is pressed, the mode

will change as follows:

• FOLDER RANDOM

The random indicator “F.RDM” will light.

The tracks in the currently selected

folder will be played in random order.

• ALL RANDOM

The random indicator “RDM” will light.

The tracks in the connected USB device

will be played in random order.

Repeat playback

Press the RPT button (5).

Each time the button is pressed, the mode

will change as follows:

• FILE REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

• FOLDER REPEAT

The repeat indicator “F.RPT” will light.

All the tracks in the folder currently

selected will be played repeatedly.

Display change

Press the DISP button (7).

Each time the button is pressed, display

will change as follows:

NOTE:

• “NO TITLE” will be displayed when there

is no text information in the disc currently

being played.

• If text data contains more than 16 char-

acters, the “>” mark will appear at the

right end. Holding down the DISP button

(7) for 1 second or longer can display the

next page.

USB (iPod

) (if equipped)

Bluetooth

audio (if equipped)

AUX (if equipped)

OFF FOLDER RANDOM ALL RANDOM

OFF FILE REPEAT FOLDER REPEAT

Play time

Folder name

File name

Album name (MP3, AAC only)

Track title

Artist name

5-48

OTHER CONTROLS AND EQUIPMENT

Notes on USB device

Compatible USB devices

• USB Mass Storage Class

For details as to whether your USB

memory/USB Audio is compatible with

USB Mass Storage Class, please con-

tact the USB memory/USB Audio manu-

facturer.

• USB Standard Compatibility 1.1/2.0 Full

Speed

• File System FAT12/16/32, VFAT

• Maximum current less than 1.0 A

• If devices such as USB hub, extension

cable are connected to the audio sys-

tem, it may not be recognized. In such

case connect the USB device directly to

the audio system.

• Devices such as MP3 player/Mobile

phone/digital camera may not be recog-

nized by the audio system for playing

music.

USB device connection

• When connecting a USB device, make

sure that the connector is pushed all the

way into the port.

• Do not leave the USB device for long

periods of time in places inside the vehi-

cle where the temperature can rise too

high.

• Back up any important data beforehand.

We cannot accept responsibility for any

lost data.

• It is recommended not to connect a USB

device that contains data files other than

MP3/WMA/AAC format.

Recording MP3/WMA/AAC files on a

USB device

• Playback or display may not be possible

depending on the type of USB device in

use or the condition of the recording.

• Depending on the connected USB mem-

ory, the files may be played in different

order from the order that the files were

stored.

Compression formats

MP3

• Bit rate

MPEG1 Audio Layer III: 32 k - 320 kbps

MPEG2 Audio Layer III: 8 k - 160 kbps

MPEG2.5 Audio Layer III: 8 k - 160 kbps

• Sampling frequency

MPEG1 Audio Layer III: 32 k/44.1 k/48 kHz

MPEG2 Audio Layer III: 16 k/22.05 k/24 kHz

MPEG2.5 Audio Layer III: 8 k/11.025 k/12 kHz

WMA (Ver. 7, Ver. 8, Ver. 9*)

• Bit rate: CBR 32 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* WMA 9 Professional/LossLess/Voice are

not supported.

AAC*

• Bit rate: ABR 16 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* Apple Lossless is not supported.

Maximum number of files/folders

• Maximum number of files: 2500

• Maximum number of files in a folder: 255

• Maximum depth of tree structure: 8

• Maximum number of folders: 255

(Root folder is included.)

5-49

OTHER CONTROLS AND EQUIPMENT

Listening to an iPod

68PH00565

(6)

(1)

(8)

(7)

(4)

(2)

(3)

(5)

Display

(1) MEDIA button

(2) TUNE FOLDER PUSH SOUND knob

(3) Up button

(4) Down button

(5) RPT button

(6) RDM button

(7) DISP button

(8) Preset buttons ([1] to [6])

(A) Track title

(B) Track number

(C)

(A)

(B)

5-50

OTHER CONTROLS AND EQUIPMENT

Selecting an iPod

mode

Press the MEDIA button (1).

Each time the button is pressed, the mode

will change as follows:

Selecting a track

• Press the Up button (3) to listen to the

next track.

• Press the Down button (4) twice to listen

to the previous track.

When the Down button (4) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/Rewinding a track

• Hold down the Up button (3) to fast for-

ward the track.

• Hold down the Down button (4) to fast

rewind the track.

Random playback

Press the RDM button (6).

Each time the button is pressed, the mode

will change as follows:

• SONG RANDOM

The random indicator “RDM” will light.

The tracks in the iPod

will be played in

random order.

• ALBUM RANDOM

The random indicator “F.RDM” will light.

The albums in the iPod

will be played in

random order.

Repeat playback

Press the RPT button (5).

Each time the button is pressed, the mode

will change as follows:

• SONG REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

Display change

Press the DISP button (7).

Each time the button is pressed, display

will change as follows:

NOTE:

If text data contains more than 16 charac-

ters, the “>” mark will appear at the right

end. Holding down the DISP button (7) for

1 second or longer can display the next

page.

USB (iPod

) (if equipped)

Bluetooth

audio (if equipped)

AUX (if equipped)

OFF SONG RANDOM ALBUM RANDOM

OFF SONG REPEAT

Playlist name /

Track title (Playlist mode only)

Artist name /

Track title

Album name /

Track title

Track title /

Play time

5-51

OTHER CONTROLS AND EQUIPMENT

Playing Mode selection

1) Press the button numbered [1] of the

Preset buttons (8) for 1 second or lon-

ger.

2) Turn the TUNE FOLDER PUSH

SOUND knob (2).

Each time the knob is turned, the mode

will change as follows:

3) Press the TUNE FOLDER PUSH

SOUND knob (2) to select the desired

mode.

NOTE:

• When the button numbered [1] of the

Preset buttons (8) is pressed, the previ-

ous mode will be displayed.

Notes on iPod

Supported iPod

• iPod

touch (5th generation)

• iPod

touch (4th generation)

• iPod

touch (3rd generation)

• iPod

touch (2nd generation)

• iPod

touch (1st generation)

• iPod

classic

• iPod

nano (7th generation)

• iPod

nano (6th generation)

• iPod

nano (5th generation)

• iPod

nano (4th generation)

• iPod

nano (3rd generation)

• iPod

nano (2nd generation)

• iPod

nano (1st generation)

• iPhone

3GS

• iPhone

* Some functions may not be available

depending on the model of iPod

* iPod

is a trademark of Apple Inc., regis-

tered in the U.S. and other countries.

* iPhone

is a trademark of Apple Inc.,

registered in the U.S. and other coun-

tries.

* Apple is not responsible for the opera-

tion of this device or its compliance with

safety and regulatory standards.

iPod

connection

• Make sure to detach the iPod

after

pressing the engine switch to change the

ignition mode to LOCK. The iPod

may

not be shut down when it is being con-

nected and may result in battery deple-

tion.

• Please do not connect iPod

accesso-

ries such as an iPod

remote control or

headphones while connecting the iPod

with the unit. The unit may not operate

correctly.

PLAYLIST

ARTIST

ALBUM

SONGS

GENRE

5-52

OTHER CONTROLS AND EQUIPMENT

AUX Function

68PH00566

(1) MEDIA button

(1)

AUX connection

To listen to auxiliary audio sources (sold

separately) through the unit, follow the

instruction below.

1) Connect the auxiliary audio source to

the AUX/USB socket (separately

attached) with an AUX cable.

2) Press the MEDIA button (1).

Each time the button is pressed, the

mode will change as follows:

CAUTION

• Before connection, mute the unit,

and also keep the volume of the

auxiliary audio source within a

range that will not cause distortion.

• When the audio source is turned

off, noise may be emitted. Be sure

to turn off the unit or switch to

another mode before turning off the

audio source.

USB (iPod

) (if equipped)

Bluetooth

audio (if equipped)

AUX (if equipped)

5-53

OTHER CONTROLS AND EQUIPMENT

NOTE:

• Please consult your place of purchase

for details about whether a given auxil-

iary audio source can be connected and

the proper auxiliary cord to use.

• The volume and tone controls of the

auxiliary audio source can be adjusted

on the unit.

• In AUX mode, the volume setting is dif-

ferent from another mode.

5-54

OTHER CONTROLS AND EQUIPMENT

Bluetooth

Hands-Free (if equipped)

68PH00567

(1) TUNE FOLDER PUSH SOUND knob

(2) VOL PUSH POWER knob

(3) Preset buttons

(4) Back button

(5) Bluetooth

setup button (on control panel)

(2)

(4)

(1)

(5)

(3)

Bluetooth

Steering switch

68PH00568

68PH00569

(6) Bluetooth

setup button (on steering

wheel)

(7) Off Hook button

(8) On Hook button

(9) MUTE switch

(10) VOL switch

(6)

(7)

(8)

(10)

(9)

5-55

OTHER CONTROLS AND EQUIPMENT

Phone registration

NOTE:

• Up to 5 phones can be registered.

• To set up a new phone, disconnect the

audio player from the unit. Connect the

audio player again after phone setup is

completed if necessary.

• When failed to establish the pairing

within 120 seconds, the connecting

operation will be canceled. Please try

again or refer to the manual of the phone

in use for how to establish the pairing

with the phone.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Blue-

tooth”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Pairing”,

and press the knob (1) to determine the

selection.

4) Select “MY CAR” from the Bluetooth

menu of the phone and establish the

pairing.

Refer to the manual of the phone in use

for further information.

5) Enter the Passkey displayed on the unit

to the phone.

6) When the pairing with the phone is

established, automatic transfer of the

phonebook and the call history

becomes selectable. The automatic

transfer starts with “Yes” and it does not

with “No”.

7) Press the On Hook button (8).

NOTE:

• When selecting “Go Back” or pressing

the back button (4), the previous menu

will be displayed.

• When additionally registering a phone,

operate the same step from 1).

Receiving a call

Press the Off Hook button (7) to receive a

call.

Ending a call

Press the On Hook button (8) to end a call.

Rejecting a call (only for supported

models)

Press the On Hook button (8) to reject a

incoming call.

Mute of Hands-free Microphone

Press the MUTE switch (9) to mute the

microphone. To cancel the mute, press the

MUTE switch (9) again.

Adjusting the listening volume

• Turn the VOL PUSH POWER knob (2)

during a call.

Turning it clockwise increases the vol-

ume; turning it counterclockwise

decreases the volume.

• Press the VOL switch (10) during a call.

Pressing “+” of the switch increases the

volume, pressing “-” of the switch

decreases the volume.

Adjusting the ring volume

• Turn the VOL PUSH POWER knob (2)

while a call coming in.

Turning it clockwise increases the vol-

ume; turning it counterclockwise

decreases the volume.

• Press the VOL switch (10) during a call.

Pressing “+” of the switch increases the

volume, pressing “-” of the switch

decreases the volume.

Adjusting the call or ringtone volume

Follow the instructions below to adjust the

call or ringtone volume.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Tele-

phone”, and press the knob (1) to deter-

mine the selection.

To use the hands-free function with this

unit, it is required to register the phone

in advance.

5-56

OTHER CONTROLS AND EQUIPMENT

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Sound Set-

ting”, and press the knob (1) to deter-

mine the selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Call Vol-

ume” or “Ringtone Volume”, and press

the knob (1) to determine the selection.

The current call or ringtone volume will

be displayed.

5) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select desired call

or ringtone volume, and press the knob

(1) to determine the selection.

NOTE:

When selecting “Go Back” or pressing the

back button (4), the previous menu will be

displayed.

Dialing using Missed/Incoming/

Outgoing Calls

Follow the instructions below to dial to the

last dialed number again.

NOTE:

Up to 30 phone numbers of the latest calls

can be stored. (30 calls including missed,

received and dialed call)

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Tele-

phone”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “All Calls”,

“Missed Calls”, “Incoming Calls” or

“Outgoing Calls”, and press the knob

(1) to determine the selection.

To dial from the dialed history or the

received history, select “All Calls”,

“Missed Calls”, “Incoming Calls” or

“Outgoing Calls” respectively.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select the desired

number, and press the knob (1) to

determine the selection.

5) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Dial”, and

press the knob (1) or the Off Hook but-

ton (7) to dial to the selected number.

NOTE:

• When selecting “Go Back” or pressing

the back button (4), the previous menu

will be displayed.

• Pressing “Confirm” after selecting “Add

Speed Dial” can register the selected

number in the speed dial.

• Pressing “Confirm” after selecting

“Delete” can delete the selected number

from the call history.

Deletion of call history

Follow the instructions below to delete a

missed/incoming/outgoing call history.

1) Press the Bluetooth® setup button (5)

or (6). The Bluetooth® setup menu will

be displayed.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Tele-

phone”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup

Phonebook”, and press the knob (1) to

determine the selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Delete His-

tory”, and press the knob (1) to deter-

mine the selection.

5) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Missed

Calls”, “Incoming Calls”, or “Outgoing

Calls”, and press the knob (1) to deter-

mine the selection.

6) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select a number to

5-57

OTHER CONTROLS AND EQUIPMENT

be deleted or “ALL”, and press the knob

(1) to determine the selection.

7) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Delete?” or

“Delete All?”, and press the knob (1) to

determine the selection.

8) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Confirm”,

and press the knob (1) to complete the

deletion.

NOTE:

When selecting “Go Back” or pressing the

back button (4), the previous menu will be

displayed.

Registration in Phonebook

Registration of numbers in the phonebook.

Follow the instructions below to register

phone numbers in the Phonebook of the

unit.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Tele-

phone”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup

Phonebook”, and press the knob (1) to

determine the selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Add Con-

tacts”, and press the knob (1) to deter-

mine the selection.

5) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Overwrite

All” or “Add One Contact”, and press

the knob (1) to determine the selection.

The “Rest of Memory XXXX: Ok?” will

be displayed.

6) Press or turn the TUNE FOLDER

PUSH SOUND knob (1) to select “Con-

firm”, and press the knob (1) to deter-

mine the selection.

7) Transfer contacts from the phone.

When the registration is completed, the

“Setup Phonebook” will be displayed.

NOTE:

• When selecting “Go Back” or pressing

the back button (4), the previous menu

will be displayed.

• Up to 1000 numbers can be registered in

Phonebook.

Transfer of call history (Call History)

Follow the instructions below to transfer

call history of the registered phone.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Tele-

phone”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Call His-

tory”, and press the knob (1) to deter-

mine the selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Overwrite

call History”, and press the knob (1) to

determine the selection.

5) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Confirm”,

and press the knob (1) to transfer the

call history from the phone.

NOTE:

When selecting “Go Back” or pressing the

back button (4), the previous menu will be

displayed.

Automatic transfer of phonebook/call

history

You can select whether or not the device

transfers the phonebook and the call his-

tory automatically when the phone is regis-

tered. Follow the instructions below to

select.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Tele-

phone”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “A.Transfer”,

and press the knob (1) to determine the

selection.

5-58

OTHER CONTROLS AND EQUIPMENT

4) Pressing the TUNE FOLDER PUSH

SOUND knob (1) switches between

“ On” and “ Off”.

NOTE:

Selecting “Go Back” or pressing the back

button (4) stores displayed setting and the

previous menu is displayed.

Making a call by Phonebook

Follow the instructions below to dial a num-

ber registered in Phonebook.

1) Press the Off Hook button (7).

The Bluetooth

phonebook menu will

be displayed.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Phone-

book”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select the initial of

the name you would like to make a call,

and press the knob (1) to determine the

selection.

The registered numbers will be dis-

played in sequence. If names have

been registered together with numbers,

the names will be displayed.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Dial”, and

press the knob (1) to determine the

selection.

5) Press the Off Hook button (7).

The displayed number or the contact

registered with the displayed name will

be dialed.

NOTE:

The system can only access the contacts

that are stored in the phone memory.

Deletion of registered data (Delete

Entry)

Follow the instructions below to delete a

number registered in Phonebook.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Tele-

phone”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup

Phonebook”, and press the knob (1) to

determine the selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Delete Con-

tacts”, and press the knob (1) to deter-

mine the selection.

5) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select a contact to

be deleted, and press the knob (1) to

determine the selection.

6) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Delete?”,

and press the knob (1) to determine the

selection.

7) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Confirm”,

and press the knob (1) to complete the

deletion.

NOTE:

When selecting “Go Back” or pressing the

back button (4), the previous menu will be

displayed.

Registration in speed dial

Follow the instructions below to assign a

number to one of the Preset buttons to use

as the speed dial.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Tele-

phone”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup

Phonebook”, and press the knob (1) to

determine the selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Add Speed

Dial”, and press the knob (1) to deter-

mine the selection.

5) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select a contact to

be assigned, and press the knob (1) to

determine the selection.

6) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Choose

5-59

OTHER CONTROLS AND EQUIPMENT

Preset”, and press the knob (1) to

determine the selection.

7) Press one of the Preset buttons (3) to

which the selected contact is to be

assigned. If a contact is already

assigned to the selected button, a con-

firmation message will be displayed.

Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Overwrite”,

and press the knob (1) to complete the

selection.

8) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Confirm”,

and press the knob (1) to complete the

assignment.

When the assignment is completed, the

“Setup Phonebook” will be displayed.

NOTE:

When selecting “Go Back” or pressing the

back button (4), the previous menu will be

displayed.

Registration in speed dial (Alternate

Method)

1) Press the Off Hook button (7).

The Bluetooth

phonebook menu will

be displayed.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “All Calls”,

”Missed Call” or “Outgoing Call”, and

press the knob (1) to determine the

selection. To select a contact / number

to be assigned from the dialed history

or the received history, select “All Calls”

,“Missed Call”, “Incoming Calls “or “Out-

going Calls” respectively.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select desired con-

tact/number, and press the knob (1) to

determine the selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Add to

speed dials”, and press the knob (1) to

assign to the selected contact/number.

5) Press one of the Preset buttons (3) to

which the selected contact is to be

assigned. If a number is already

assigned to the selected button, a con-

firmation message will be displayed.

Turn the TUNE FOLDER PUSSH

SOUND knob (1) to select “Overwrite?”,

and press the knob (1) to determine the

selection.

6) Turn the TUNE FOLDER PUSSH

SOUND knob (1) to select “Confirm”,

and press the knob (1) to complete the

assignment.

NOTE:

When selecting “Go Back” or pressing the

back button (4), the previous menu will be

displayed.

One-touch call (Speed dial)

Follow the instructions below to dial the

number assigned to each of the Preset

buttons (3).

1) Press the Off Hook button (7).

The Bluetooth

phonebook menu will

be displayed.

Pressing one of the Preset buttons (3)

can skip step 2) and the 1st line of step

3).

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Speed

Dials”, and press the knob (1) to deter-

mine the selection.

3) Press one of the Preset buttons (3).

The assigned number/contact will be

displayed. When no number is

assigned, “No Entry” is displayed.

4) Press the Off Hook button (7).

The selected number will be dialed.

5-60

OTHER CONTROLS AND EQUIPMENT

Deletion of speed dial (Del Speed Dial)

To delete a number assigned for the speed

dial, follow the instructions below.

1) Press the Off Hook button (7).

The Bluetooth

phonebook menu will

be displayed.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Speed

Dials”, and press the knob (1) to deter-

mine the selection.

3) Press one of the Preset buttons (3) to

which the number to be deleted is

assigned.

“No Entry” appears if the number is not

registered.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Delete”, and

press the knob (1) to determine the

selection.

5) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Del Speed

Dial”, and press the knob (1) to deter-

mine the selection.

6) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Confirm”,

and press the knob (1) to complete the

deletion.

NOTE:

When selecting “Go Back” or pressing the

back button (4), the previous menu will be

displayed.

Display of device data (Device Name)

Follow the instructions below to display the

BD (Bluetooth

Device) address and

device name.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Blue-

tooth”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Bluetooth

Info”, and press the knob (1) to deter-

mine the selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Device

Name” or “Device Address”, and press

the knob (1) to display the device name

or the BD (Bluetooth

Device) address.

NOTE:

When selecting “Go Back” or pressing the

back button (4), the previous menu will be

displayed.

Reset to the factory defaults

Follow the instructions below to reset all

the settings to the factory defaults.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Blue-

tooth”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Initialize”,

and press the knob (1) to determine the

selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “All Initial-

ize”, and press the knob (1) to deter-

mine the selection.

5) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Confirm”,

and press the knob (1) to start the

reset.

NOTE:

When selecting “Go Back” or pressing the

back button (4), the previous menu will be

displayed.

5-61

OTHER CONTROLS AND EQUIPMENT

Selection of phone (Select Phone)

Follow the instructions below to select a

phone to be paired with from the registered

phones.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Blue-

tooth”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “List Phone”,

and press the knob (1) to determine the

selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select a phone to

be paired with, and press the knob (1)

to determine the selection.

5) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Select”, and

press the knob (1) to determine the

selection.

NOTE:

• When selecting “Go Back” or pressing

the back button (4), the previous menu

will be displayed.

• The Bluetooth

ready audio device will

be disconnected when the phone is

selected.

List of phones (List Phones)

Follow the instructions below to display the

names of the registered phones in

sequence.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Blue-

tooth”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “List Phone”,

and press the knob (1) to determine the

selection.

The names of the registered phones

are displayed in sequence.

NOTE:

When selecting “Go Back” or pressing the

back button (4), the previous menu will be

displayed.

Passkey setting (Set Passkey)

Follow the instructions below to set the

security number (Passkey).

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Blue-

tooth”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Passkey”,

and press the knob (1) to determine the

selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “New Pass-

key”, and press the knob (1) to deter-

mine the selection.

5) Press or turn the TUNE FOLDER

PUSH SOUND knob (1) to select “Con-

firm”.

6) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select a number for

the first digit, and press the knob (1) to

determine the selection. Select and

determine numbers for the second,

third and fourth digits in order in the

same manner. When not entering up to

the eighth digit, enter blanks for the

successive digits.

7) Turn the TUNE FOLDER PUSH

SOUND knob (1) to determine the

passkey setting.

NOTE:

When selecting “Go Back” or pressing the

back button (4), the previous menu will be

displayed.

5-62

OTHER CONTROLS AND EQUIPMENT

Deletion of phone information (Delete

Phone)

Follow the instructions below to delete the

registered information of the phone.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Blue-

tooth”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “List Phone”,

and press the knob (1) to determine the

selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select a phone to

be deleted, and press the knob (1) to

determine the selection.

5) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Delete

Phone”, and press the knob (1) to

determine the selection.

6) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Delete?”,

and press the knob (1) to determine the

selection.

7) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Confirm”,

and press the knob (1) to determine the

selection.

NOTE:

When selecting “Go Back” or pressing the

back button (4), the previous menu will be

displayed.

BT function on/off (BT Power)

Follow the instructions below to turn on/off

the Bluetooth

function.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “Setup Blue-

tooth”, and press the knob (1) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (1) to select “BT Power”,

and press the knob (1) to determine the

selection.

4) Press the TUNE FOLDER PUSH

SOUND knob (1) to select “BT Power

On” or “BT Power Off”.

NOTE:

• When the BT function is turned off, the

connection between this unit and the

registered phone in use will be discon-

nected.

• When selecting “Go Back” or pressing

the back button (4), the previous menu

will be displayed.

5-63

OTHER CONTROLS AND EQUIPMENT

Bluetooth

audio (if equipped)

68PH00570

(1)

(2)

(4)

(3)

(5)

(6)

(7)

Bluetooth

Steering switch

68PH00571

Display

(1) MEDIA button

(2) TUNE FOLDER PUSH SOUND knob

(3) Up button

(4) Down button

(5) DISP button

(6) Back button

(7) Bluetooth

setup button (on control

panel)

(8) Bluetooth

setup button (on steering

wheel)

(A) Track number

(B) Play time

(8)

(B)

(A)

5-64

OTHER CONTROLS AND EQUIPMENT

Registration of audio devices

NOTE:

• To set up a new audio player, disconnect

the phone from the unit. Connect the

phone after audio player setup is com-

pleted if necessary.

• When failed to establish the connection

within 120 seconds, the connecting

operation will be canceled. Please try

again or refer to the audio player manual

for assistance with the pairing process.

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “Setup Blue-

tooth”, and press the knob (2) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “Pairing”,

and press the knob (2) to determine the

selection.

4) Select “My Car” from the Bluetooth

menu of the audio player and establish

the pairing.

Refer to the manual of the audio player

in use for further information.

5) Enter the Passkey displayed on the unit

to the audio player.

NOTE:

• When selecting “Go Back” or pressing

the back button (6), the previous menu

will be displayed.

• When additionally registering audio

devices, operate the same step from 1).

Selecting the Bluetooth

audio mode

Press the MEDIA button (1).

Each time the button is pressed, the mode

will change as follows:

Selecting a group (only for supported

models)

Turn the TUNE FOLDER PUSH SOUND

knob (2) to select a group.

Selecting a track

• Press the Up button (3) to listen to the

next track.

• Press the Down button (4) twice to listen

to the previous track.

When the Down button (4) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/Rewinding a track

• Hold down the Up button (3) to fast for-

ward the track.

• Hold down the Down button (4) to fast

rewind the track.

NOTE:

Some functions may not be available

depending on Bluetooth

audio.

Display change

Press the DISP button (5).

Each time the button is pressed, display

will change as follows:

NOTE:

If text data contains more than 16 charac-

ters, the “>” mark will appear at the right

end. Holding down the DISP button (5) for

1 second or longer can display the next

page.

To use Bluetooth

ready audio devices

with this unit, it is required to register the

devices.

USB (iPod

) (if equipped)

Bluetooth

audio (if equipped)

AUX (if equipped)

Play time

Track name

Artist name

Album name

5-65

OTHER CONTROLS AND EQUIPMENT

Selection of audio device (Select Audio)

Follow the instructions below to select an

audio device to be paired with from the

registered audio devices.

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “Setup Blue-

tooth”, and press the knob (2) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “List Audio”,

and press the knob (2) to determine the

selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select an audio

device to be used, and press the knob

(2) to determine the selection.

5) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “Select”, and

press the knob (2) to determine the

selection.

6) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “Confirm”,

and press the knob (2) to complete the

pairing.

NOTE:

• When selecting “Go Back” or pressing

the back button (6), the previous menu

will be displayed.

• The phone will be disconnected when

the Bluetooth

ready audio device is

selected.

List of audio devices (List Audio)

Follow the instructions below to display the

names of the registered audio devices in

sequence.

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “Setup Blue-

tooth”, and press the knob (2) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “List Audio”,

and press the knob (2) to determine the

selection. The names of registered

audio devices will be displayed in

sequence.

NOTE:

When selecting “Go Back” or pressing the

back button (6), the previous menu will be

displayed.

Passkey setting (Set Passkey)

Follow the instructions below to set the

security number (Passkey).

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “Setup Blue-

tooth”, and press the knob (2) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “Passkey”,

and press the knob (2) to determine the

selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “New Pass-

key”, and press the knob (2) to deter-

mine the selection.

5) Press or turn the TUNE FOLDER

PUSH SOUND knob (2) to select “Con-

firm”.

6) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select a number for

the first digit, and press the knob (2) to

determine the selection. Select and

determine numbers for the second,

third and fourth digits in order in the

same manner. When not entering up to

the eighth digit, enter blanks for the

successive digits.

7) Turn the TUNE FOLDER PUSH

SOUND knob (2) to determine the

passkey setting.

NOTE:

When selecting “Go Back” or pressing the

back button (6), the previous menu will be

displayed.

5-66

OTHER CONTROLS AND EQUIPMENT

Deletion of audio device information

(Delete Audio)

Follow the instructions below to delete the

registered information of audio device.

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “Setup Blue-

tooth”, and press the knob (2) to deter-

mine the selection.

3) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “List Audio”,

and press the knob (2) to determine the

selection.

4) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select an audio

device to be deleted, and press the

knob (2) to determine the selection.

5) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “Delete”, and

press the knob (2) to determine the

selection.

6) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “Delete?”,

and press the knob (2) to determine the

selection.

7) Turn the TUNE FOLDER PUSH

SOUND knob (2) to select “Confirm”,

and press the knob (2) to complete the

deletion.

NOTE:

When selecting “Go Back” or pressing the

back button (6), the previous menu will be

displayed.

Disclaimer for Bluetooth

function

• Depending on the mobile phone models,

some phones may not be compatible

fully or partially (some function may be

restricted).

• Connectivity or voice quality may get

affected depending on circumstances.

• After the ignition switch is turned to the

“ON” position, the audio system takes

few seconds to detect and connect to

the Bluetooth

device (if already paired).

Remote Audio Controls

(if equipped)

Controlling of basic functions of the audio

system is available using the switches on

the steering wheel.

68PH00572

(1)

(2) (3)

(4)

5-67

OTHER CONTROLS AND EQUIPMENT

Adjusting the volume

• To increase the volume, hold down “+” of

the VOL switch (1). The volume will keep

on being increased until the switch is

released.

• To decrease the volume, hold down “-” of

the VOL switch (1). The volume will keep

on being decreased until the switch is

released.

• To mute the sound, press the switch (2).

Selecting the mode

Press the switch (3).

Each time the button is pressed, the mode

will change as follows:

It is possible to turn on the audio system

by pressing the switch (3).

Selecting the radio station (FM1, FM2,

AM mode)

• To select the next preset station, press

“ ” of the switch (4) only for a moment.

• To select the previous preset station,

press “ ” of the switch (4) only for a

moment.

• To scan a higher frequency radio station,

press “ ” of the switch (4) for 1 second

or longer.

• To scan a lower frequency radio station,

press “ ” of the switch (4) for 1 second

or longer.

Selecting the track (CD, USB (iPod

Bluetooth

audio mode)

• To skip to the next track, press “ ” of the

switch (4) only for a moment.

• To skip to the previous track, press “ ” of

the switch (4) twice only for a moment.

When the switch (4) is pushed down

once only for a moment, the track cur-

rently being played will start from the

beginning again.

Fast forwarding/Rewinding a track

• To fast forward, press “ ” of the switch

(4) for 1 second or longer.

• To fast rewind, press “ ” of the switch (4)

for 1 second or longer.

FM1 (Radio)

FM2 (Radio)

Bluetooth

audio (if equipped)

AUX (if equipped)

USB (iPod

) (if equipped)

AM (Radio)

5-68

OTHER CONTROLS AND EQUIPMENT

Anti-Theft Feature

68PH00573

(1)

(4)

(3)

(2)

(1) VOL PUSH POWER knob

(2) Preset buttons ([1] to [6])

(3) Up button

(4) TUNE FOLDER PUSH SOUND knob

5-69

OTHER CONTROLS AND EQUIPMENT

The anti-theft function is intended to dis-

courage thefts, such as that the audio sys-

tem becomes inoperable when it is

installed on other vehicles.

This function works by entering a Personal

Identification Number (PIN).

When the unit is disconnected from its

power source, such as when the audio

system is removed or the battery is discon-

nected, the unit will become inoperable

until the PIN is reentered.

Setting the Anti-Theft Function

1) Press the VOL PUSH POWER knob (1)

to power off.

2) Hold down the buttons numbered [1]

and [6] of the Preset buttons (2) and

press the VOL PUSH POWER knob (1).

“SECURITY” will be displayed.

3) Press the Up button (3) and the button

numbered [1] of the Preset buttons (2)

simultaneously.

4) Enter a 4-digit number to be registered

as PIN using the buttons numbered [1] -

[4] of the Preset buttons (2).

5) Hold down the TUNE FOLDER PUSH

SOUND knob (4) for 1 second or longer

to set the anti-theft function.

NOTE:

Take a note of the registered PIN and keep

it for the future use.

Canceling the anti-theft feature

To cancel the anti-theft function, delete the

registered PIN.

1) Press the VOL PUSH POWER knob (1)

to power off.

2) Hold down the buttons numbered [1]

and [6] of the Preset buttons (2) and

press the VOL PUSH POWER knob (1).

“PIN ENTRY” will be displayed.

3) Press the Up button (3) and the button

numbered [1] of the Preset buttons (2)

simultaneously.

4) Enter a 4-digit number to be registered

as PIN using the buttons numbered [1] -

[4] of the Preset buttons (2).

5) Hold down the TUNE FOLDER PUSH

SOUND knob (4) for 1 second or longer

to delete the registered PIN. The indi-

cation “----” will be displayed and the

anti-theft function will be canceled.

NOTE:

To change your PIN, first delete your cur-

rent PIN, then set a new one.

Confirming the Personal Identification

Number (PIN)

When the main power source is discon-

nected such as when the battery is

replaced, etc, it is required to enter the PIN

to make the unit operable again.

1) Set the ignition switch to the “ACC”

position.

“SECURITY” will be displayed.

2) Press the Up button (3) and the button

numbered [1] of the Preset buttons (2)

simultaneously.

3) Enter a 4-digit number to be registered

as PIN using the buttons numbered [1] -

[4] of the Preset buttons (2).

4) Hold down TUNE FOLDER PUSH

SOUND knob (4) for 1 second or lon-

ger.

When the PIN same as registered is

entered, the power of the audio system

will be turned off automatically and it

will become operable again.

NOTE:

If an incorrect PIN is entered, “ERROR”

and the total number of incorrect entry

attempts will be displayed.

If an incorrect PIN is entered 10 times,

“HELP” will be displayed and the audio

system will become inoperable.

5-70

OTHER CONTROLS AND EQUIPMENT

Battery Installation

Install a lithium battery (CR2025) with the poles facing the correct direction.

68PM5001

Battery replacement timing

• When battery power is depleted, the button may not be operable. If the remote controller

does not operate, replace the battery and check the operation.

Caution on battery

• Be sure to follow the instructions to prevent battery leakage, over-heating, ignition or

explosion.

If battery leakage has occurred, wipe the

container first then install a new battery. If

the battery solution contacts the skin, wash

off with water completely.

WARNING

• Do not expose the battery to flame.

Do not short circuit, disassemble,

or heat the battery.

• Do not charge the battery.

• Use the specified type battery.

• Keep the button-shaped battery

away from children to prevent acci-

dental swallowing.

If the battery is swallowed, contact a

doctor immediately.

CAUTION

• Install the battery with the poles

facing the correct direction.

• When not in use for a long period

of time, or if the battery is dead,

remove the battery from the remote

controller.

5-71

OTHER CONTROLS AND EQUIPMENT

Caution on Remote Controller

• Do not leave the remote controller in an

area exposed to direct sunlight, such as

on the dashboard or steering wheel. The

remote controller may deform because

of the heat, (Be especially careful of the

dashboard exposed to direct sunlight in

the summer, as it will become extremely

hot).

• When the vehicle is parked in an area

exposed to direct sunlight, Ensure the

remote controller is placed in an area not

exposed to direct sunlight. For example:

Glove box.

Under direct sunlight, signal reception

from the remote controller weakens. If

this happens, hold the remote controller

close to the signal receptor on the front

panel.

5-72

OTHER CONTROLS AND EQUIPMENT

Remote Controller

Common operations

In Sound Mode

Press to adjust the sound.(bass/treble/balance/fader)

In Preset-EQ Mode

The Preset-EQ setting switches as follows:

In AVC Mode

The AVC setting switches

as follows:

TUNE FOLDER UP/DOWN button

OFF (FLAT)

JAZZ

ROCK

POP

CLASSIC

HIP-HOP

OFF

LEVEL 1

LEVEL 2

LEVEL 3

Power ON / OFF

POWER button

Press to adjust volume.

(including at AUX mode)

VOLUME button

Press to mute the sound. Press it again to cancel

the mute.

MUTE button

While playback, the sound

mode switches as follows

(including at AUX mode,

except while displaying

iPod

menu):

SOUND button

Preset-EQ

BASS

TREBLE

BALANCE

FADER

AVC

The mode switches as

follows:

MODE button

FM1

FM2

Bluetooth

audio

(if equipped)

AUX (if equipped)

USB (iPod

)

(if equipped)

5-73

OTHER CONTROLS AND EQUIPMENT

Radio operations

NOTE:

When there are fewer than 6 stations that can be stored even if 1 round of auto store operation is performed, no station will be

stored at the remaining preset buttons.

Press to return to the last received fre-

quency in the previous auto store mode.

Press it for 2 seconds or longer. It selects

the stations with the stronger signals and

stores them in order.

AS button

Press to select the radio station.

SEEK TRACK UP/DOWN button

Press to select the desired preset station.

PRESET buttons (1-6)

5-74

OTHER CONTROLS AND EQUIPMENT

CD operations

Press to play the current track randomly.

Press it again to cancel.

RDM button

Press to plays the current track repeatedly.

Press it again to cancel.

RPT button

Press to skip to the next/previous track.

Press it for 1 second or longer to fast-forward/

fast-rewind the track.

SEEK TRACK UP/DOWN button

The display switches as follows:

Press it for 1 second or longer to display the

next page.

DISP button

Play time

Disc title

Track title

5-75

OTHER CONTROLS AND EQUIPMENT

MP3/WMA/AAC Disc operations

The repeat mode switches as follows:

RPT button

OFF

FILE REPEAT

FOLDER REPEAT

The display switches as follows:

Press it for 1 second or longer to display the next

page.

DISP button

Play time

Folder name

File name

Album name (MP3, AAC only)

Track title

Artist name

Press to skip to the next/previous track.

Press it for 1 second or longer to fast-forward/fast-

rewind the track.

SEEK TRACK UP/DOWN button

The random mode switches as follows:

RDM button

OFF

FOLDER RANDOM

ALL RANDOM

Press to skip to the next/previous folder.

TUNE FOLDER UP/DOWN button

5-76

OTHER CONTROLS AND EQUIPMENT

USB operations

The repeat mode switches as follows:

RPT button

OFF

FILE REPEAT

FOLDER REPEAT

The display switches as follows:

Press it for 1 second or longer to display the next

page.

DISP button

Play time

Folder name

File name

Album name (MP3, AAC only)

Track title

Artist name

Press to skip to the next/previous folder.

TUNE FOLDER UP/DOWN button

Press to skip to the next/previous file.

Press it for 1 second or longer to fast-forward/fast-

rewind the file.

SEEK TRACK UP/DOWN button

The random mode switches as follows:

RDM button

OFF

FOLDER RANDOM

ALL RANDOM

5-77

OTHER CONTROLS AND EQUIPMENT

iPod

operations

The random mode switches as follows:

RDM button

OFF

SONG RANDOM

ALBUM RANDOM

Press to play the current track repeatedly.

Press it again to cancel.

RPT button

The display switches as follows:

Press it for 1 second or longer to display the next

page.

DISP button

Playlist name /

Track title (Playlist mode only)

Artist name / Track title

Album name / Track title

Track title / Play time

While displaying iPod

menu, press to select the

desired item and display the list. When a track is

selected from the list, the playback starts.

ENT button

During playback

• Press to display iPod

menu.

• Press it for 1 second or longer to display the top menu.

While iPod

menu is displayed

• Press to display the folder in one layer upper.

• Press it for 1 second or longer to display the top menu.

MENU button

While displaying iPod

menu, press to dis-

play the next/previous list in the same layer.

TUNE FOLDER UP/DOWN button

Press to skip to the next/previous file.

Press it for 1 second or longer to fast-forward/fast-

rewind the file.

SEEK TRACK UP/DOWN button

5-78

OTHER CONTROLS AND EQUIPMENT

Troubleshooting

When encountered a problem, check and follow the instructions as described below.

If the described suggestions do not solve the problem, it is recommended to take the unit to your authorised Maruti Suzuki workshop.

Problem Possible cause Possible solution

Common

Unable to operate The security function is on.

When “SECURITY” is displayed, enter

the ID.

When “HELP” is displayed, contact your

authorised Maruti Suzuki workshop.

Unable to turn on the power (no sound).

(No sound is produced)

Fuse is blown.

Contact your authorised Maruti Suzuki

workshop.

Radio

Much noise

It may not be exactly tuned in to the sta-

tion.

Tune it in exactly to the station.

Unable to receive by auto tuning

There may be no station emitting signals

powerful enough.

Pick up a station by manual tuning.

Sound skips or noise produced

The disc is dirty. Wipe the disc with a soft cloth.

The disc has a major scratch or is

warped.

Replace the disc with the one with no

scratch and also not warped.

5-79

OTHER CONTROLS AND EQUIPMENT

MP3/WMA/AAC

No playback

The disc contains unsupported formatted

data.

Check the file format.

Sound skips or noise produced

Sound skipping may occur when playing

VBR (Variable Bit Rate) files.

It is not recommended to play VBR files.

USB

Playback does not start when the USB

device is connected.

There is no supported format file to play

on this unit.

Check the file format.

The current consumption of the USB

device exceeds 1.0 A.

Use an USB device with a current con-

sumption lower than 1.0 A.

Bluetooth

Pairing failed

The distance between this unit and the

Bluetooth

ready device is too far, or a

metallic object may be located between

the Bluetooth

ready device and this unit.

Change the location of the Bluetooth

ready device.

The Bluetooth

function of the Blue-

tooth

ready device is off.

Refer to the manual of the Bluetooth

ready device. (Some devices have the

power saving function that automatically

activates after a certain time.)

Unable to receive a call.

Your current location may be out of ser-

vice area.

Drive your vehicle to the service area of

the phone.

The voice quality of hands-free is low

(Distortion, noise etc.).

Another wireless device may be located

near the unit.

Switch off the wireless device or keep it

away from the unit.

Problem Possible cause Possible solution

5-80

OTHER CONTROLS AND EQUIPMENT

Error Display Messages

Display Possible cause Possible solution

ERROR 1 The disc cannot be read.

Insert the disc with its label side up.

Check the disc if it is not warped or is free of flaws.

When ERROR 1 does not disappear even when a nor-

mal disc is inserted, contact your authorised Maruti

Suzuki workshop.

ERROR 3

The player developed an error of an

unidentified cause.

When the CD is in the unit, press the CD eject button to

remove the disc.

When the disc cannot be ejected, contact your autho-

rised Maruti Suzuki workshop.

USB/iPod

ERROR 1 The USB device is disconnected. Check the connection of the USB device.

ERROR 2

Impossible to communicate correctly with

the USB device.

Unplug the USB device and plug it again.

Check the USB device.

ERROR 3 Inoperable due to an unidentified cause.

Unplug the USB device and plug it again.

When ERROR 3 does not disappear, contact your autho-

rised Maruti Suzuki workshop.

ERROR 4

The current consumption of the USB

device exceeds 1.0 A.

Check the USB device.

5-81

OTHER CONTROLS AND EQUIPMENT

Bluetooth

ERROR 1

The player developed an error of an

unidentified cause.

Disconnect the Bluetooth

ready device and connect it

again.

When ERROR 1 does not disappear, contact your autho-

rised Maruti Suzuki workshop.

Connection

Failed

Failed to establish pairing or connection Try to establish the pairing or connection again.

Memory Full

Reached the limit for the number of phone-

book data in transfer

Delete registered data of unnecessary number in phone-

book and try to transfer the register phone numbers in

the phonebook again.

Not Available Inoperable during driving Operate the system after pulling over your car.

Display Possible cause Possible solution

Other Controls and Equipment for Your Suzuki Baleno 4 Door Second Generation (2015-2021)

Related Topics

Popular Owner Manuals

Latest Owner Manuals