2015-2021 Suzuki Baleno 4 Door Other Controls and Equipment -> Audio System (if equipped) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Other Controls and Equipment -> Audio System (if equipped) for Your Suzuki Baleno 4 Door Second Generation (2015-2021)

5-31
OTHER CONTROLS AND EQUIPMENT
Audio System (if equipped)
AM/FM CD PLAYER
68PH00575
NOTE:
For vehicle equipped with SMARTPLAY INFOTAINMENT SYSTEM, refer to audio manual available with the vehicle.
5-32
OTHER CONTROLS AND EQUIPMENT
Safety Information Notes on Discs
Precautions
• When the inside of the vehicle is very
cold and the player is used soon after
switching on the heater, condensation
may form on the disc or the optical parts
of the player and proper playback may
not be possible. If condensation forms
on the disc, wipe it off with a soft cloth. If
condensation forms on the optical parts
of the player, do not use the player for
about one hour. This will allow the con-
densation to disappear normally.
• Driving on extremely bumpy roads which
cause severe vibrations may cause
sound to skip.
• This unit uses a precision mechanism.
Even in the event that trouble arises,
never open the case, disassemble the
unit, or lubricate the rotating parts.
Please bring the unit to an authorised
Maruti Suzuki workshop.
Cautions on Handling
52D274
This unit has been designed specifically for
playback of compact discs bearing mark
(A) shown above.
No other discs can be played.
52D275
To remove the compact disc from its stor-
age case, press down on the center of the
case and lift the disc out, holding it care-
fully by the edges.
Always handle the compact disc by the
edges.
Never touch the surface.
WARNING
If you pay extended attention to oper-
ating the audio system or viewing the
audio system display while driving,
an accident can occur. If you set the
sound volume too loud, it could pre-
vent you from being aware of road
and traffic conditions.
• Keep your eyes on the road and
your mind on the drive. Avoid pay-
ing extended attention to operating
the audio system or viewing the
audio system display.
• Familiarize yourself with the audio
system controls and operation of
the audio system before driving.
• Preset your favorite radio stations
before driving so that you can
quickly tune to them using the pre-
sets.
• Set the sound volume to a level
that will allow you to continue to be
aware of road and traffic conditions
while driving.
(A)
(
A
)
Removing the disc
Proper way to hold
the compact disc
5-33
OTHER CONTROLS AND EQUIPMENT
52D347
To remove fingermarks and dust, use a
soft cloth, and wipe in a straight line from
the center of the compact disc to the cir-
cumference.
52D277
New discs may have some roughness
around the edges. The unit may not work
or the sound may skip if such discs are
used. Use a ball-point pen (B), etc. to
remove the roughness (C) from the edges
of the disc before inserting it into the unit.
52D348
Never stick labels on the surface of the
compact disc or write on the surface with a
pencil or pen.
52D349
Do not use any solvents such as commer-
cially available cleaners, anti-static spray,
or thinner to clean compact discs.
52D350
Do not use compact discs that have large
scratches, are misshaped, or cracked, etc.
Use of such discs will cause damage or
prevent the system from operating prop-
erly.
52D351
Do not expose compact discs to direct sun-
light or any heat source.
NOTE:
• Do not use commercially available CD
protection sheets or discs equipped with
stabilizers, etc.
These may get caught in the internal
mechanism and damage the disc.
• It may be impossible to play CD-R discs
with this unit due to the recording condi-
tions.
• CD-RW discs cannot be played with this
unit.
(B)
(B)
(C)
(
B
)
(
B
)
(C)
5-34
OTHER CONTROLS AND EQUIPMENT
The Bluetooth
®
word mark and logo are
registered trademarks and are owned by
the Bluetooth SIG, Ink.
Stop using this unit and a Bluetooth
®
ready device whenever requested.
This unit shares the communication fre-
quency with other private or public wireless
communication equipment such as a wire-
less LAN and other wireless communica-
tion radios.
You should stop using this unit whenever
you are notified that your unit disturbs
other wireless communication immediately.
WARNING
This is a class I laser product. Use of
controls or adjustments or perfor-
mance of procedures other than
those specified herein may result in
hazardous radiation exposure.
Do not open covers and do not
attempt to repair this unit by yourself.
Refer servicing to qualified person-
nel.
5-35
OTHER CONTROLS AND EQUIPMENT
Basic Operations
68PH00560
(1) VOL PUSH POWER knob
(2) TUNE FOLDER PUSH SOUND knob
(1)
(2)
Turning power on/off
Press the VOL PUSH POWER knob (1).
The unit starts in the function mode it was
in when the power was turned off last.
Adjusting the volume
Turn the VOL PUSH POWER knob (1).
Turning it clockwise increases the volume;
turning it counterclockwise decreases the
volume.
NOTE:
While driving, adjust the volume to an
extent that sound and/or noise coming
from outside the vehicle can be heard.
5-36
OTHER CONTROLS AND EQUIPMENT
Adjusting bass/treble/balance /fader
1) Press the TUNE FOLDER PUSH
SOUND knob (2).
Each time the knob is pressed, sound
adjustment will change as follows:
2) Turn the TUNE FOLDER PUSH
SOUND knob (2) to adjust the sound.
Adjusting the AVC (Auto volume con-
trol)
The Auto Volume Control (AVC) function
automatically adjusts (increases/
decreases) the sound volume in accor-
dance with vehicle speed. The AVC control
is provided with three selectable levels
(LEVEL OFF, 1, 2, 3). The range of volume
adjustment increases together with the
LEVEL number.
1) Press the TUNE FOLDER PUSH
SOUND knob (2) until the AVC adjust-
ment mode is selected.
2) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select the desired
AVC adjustment level. (Initial setting:
LEVEL 2)
Preset-EQ
Preset-EQ calls up various sound types in
accordance with the listening music type.
1) Press the TUNE FOLDER PUSH
SOUND knob (2) several times until
“PRESET-EQ” appears.
2) Turn the TUNE FOLDER PUSH
SOUND knob (2).
Each time the knob is turned, preset
EQ mode will change as follows:
Preset-EQ (EQ OFF)
Bass adjustment (BASS 0)
Treble adjustment (TREBLE 0)
Balance adjustment (BALANCE 0)
Fader adjustment (FADER 0)
AVC adjustment (AVC LEVEL 2)
OFF (FLAT)
JAZZ
ROCK
POP
CLASSIC
HIP-HOP
5-37
OTHER CONTROLS AND EQUIPMENT
Listening to the Radio
68PH00561
(7)
(1)
(2)
(5)
(4)
(3)
(6)
Display
(1) FM button
(2) AM button
(3) Up button
(4) Down button
(5) TUNE FOLDER PUSH SOUND knob
(6) Preset buttons ([1] to [6])
(7) AS button
(A) Band
(B) Frequency
(A)
(B)
5-38
OTHER CONTROLS AND EQUIPMENT
Selecting the FM band
Press the FM button (1).
Each time the button is pressed, the recep-
tion band will change as follows:
Selecting the AM band
Press the AM button (2).
Seek tuning
Press the seek Up button (3) or the seek
Down button (4).
The unit stops searching for a station at a
frequency where a broadcast station is
available.
Manual tuning
Turn the TUNE FOLDER PUSH SOUND
knob (5).
The frequency being received is displayed.
Preset memory
1) Select the desired station.
2) Hold down a desired button ([1] to [6])
of the Preset buttons (6) to which you
want to store the station for 2 seconds
or longer.
Auto store
Hold down the AS button (7) for 2 seconds
or longer.
Six stations in good reception will automat-
ically be stored to the Preset buttons (6) in
order, starting from a station whose fre-
quency is the lowest.
NOTE:
• Auto store can be released by pressing
AS button (7) while auto store is under
way.
• When the auto store is performed, the
station previously stored in the memory
at the position is overwritten.
• When there are fewer than 6 stations
that can be stored even if 1 round of
auto store operation is performed, no
station will be stored at the remaining
Preset buttons (6).
• 6 stations can be preset for FM1 and
FM2 in common, and 6 stations for AM
in auto store mode.
Auto store mode on/off
Press the AS button (7).
Each time the button is pressed, the mode
is switched as follows:
Radio Reception
Radio reception can be affected by envi-
ronment, atmospheric conditions, or radio
signal’s power and distance from the sta-
tion. Nearby mountains and buildings may
interfere or deflect radio reception, causing
poor reception. Poor reception or radio
static can also be caused by electric cur-
rent from overhead wires or high voltage
power lines.
FM1 FM2
AS mode on AS mode off
5-39
OTHER CONTROLS AND EQUIPMENT
Listening to a CD
68PH00562
(8)
(6)
(5)
(4)
(2)
(7)
(3)
(1)
Display
(1) Insertion slot
(2) Eject button
(3) CD button
(4) Up button
(5) Down button
(6) RPT button
(7) RDM button
(8) DISP button
(A) Track number
(B) Play time
NOTE:
This product does not support 8 cm CD
(sometimes called as “mini single CD”, “3-
inch CD”, “CD3”, etc.).
(B)
(A)
5-40
OTHER CONTROLS AND EQUIPMENT
52D274
• CDs or CD-ROMs carrying no mark (A)
cannot be used.
• Some discs recorded in CD-R/CD-RW
format may sometimes be impossible to
use.
52D291
• A CD is to be inserted with its label side
up.
• When there is a CD already in the unit, it
is impossible to insert another CD with-
out ejecting the CD in the unit. Do not
use force to insert a CD into the CD
insertion slot.
Loading a CD
Insert a CD in the Insertion slot (1).
When a CD is loaded, It begins to play.
Ejecting a CD
Press the Eject button (2).
When the ignition mode is “LOCK”, the CD
remained ejected for around 15 seconds or
longer will automatically be drawn inside
the unit. (Auto reload function)
The backup eject function:
This function allows you to eject a CD by
pressing the Eject button (2) even when
the ignition mode is off.
Listening to a CD
When a CD is inserted, playback will auto-
matically start.
When a CD is already inside the unit,
press the CD button (3) to start playback.
Selecting a track
• Press the Up button (4) to listen to the
next track.
• Press the Down button (5) twice to listen
to the previous track.
When the Down button (5) is pressed
once, the track currently being played
will start from the beginning again.
Fast forwarding/Rewinding a track
• Hold down the Up button (4) to fast for-
ward the track.
• Hold down the Down button (5) to fast
rewind the track.
(A)
A
NOTICE
• Never insert your finger or hand
into the CD insertion slot. Never
insert foreign objects.
• Never insert a CD with glue coming
out from adhesive tape or a rental
CD label or with a trace indicating
that adhesive tape or a rental CD
label has been removed. This may
cause the CD not to eject or result
in a malfunction.
NOTICE
If you forcefully try to push an
ejected CD inside the unit before auto
reloading, the disc surface might be
scratched.
When reloading a CD, remove it from
the unit completely before reloading.
5-41
OTHER CONTROLS AND EQUIPMENT
Random playback
Press the RDM button (7).
Each time the button is pressed, the mode
will change as follows:
• TRACK RANDOM
The random indicator “RDM” will light.
The tracks in the loaded disc will be
played in random order.
Repeat playback
Press the RPT button (6).
Each time the button is pressed, the mode
will change as follows:
• TRACK REPEAT
The repeat indicator “RPT” will light.
The track currently being played will be
played repeatedly.
Display change
Press the DISP button (8).
Each time the button is pressed, display
will change as follows:
NOTE:
• “NO TITLE” will be displayed when there
is no text information in the disc currently
being played.
• If text data contains more than 16 char-
acters, the “>” mark will appear at the
right end. Holding down the DISP button
(8) for 1 second or longer can display the
next page.
OFF TRACK RANDOM
OFF TRACK REPEAT
Play time
Disc title
Track title
5-42
OTHER CONTROLS AND EQUIPMENT
Listening to an MP3/WMA/AAC Disc
68PH00563
(6)
(4)
(3)
(1)
(2)
(5)
Display
(1) TUNE FOLDER PUSH SOUND knob
(2) Up button
(3) Down button
(4) RPT button
(5) RDM button
(6) DISP button
(A) Folder number
(B) Track number
(C) Play time
(D) DISC type
(C)
(B)(A)
(D)
5-43
OTHER CONTROLS AND EQUIPMENT
Selecting a folder
Turn the TUNE FOLDER PUSH SOUND
knob (1) to select a folder.
Selecting a track
• Press the Up button (2) to listen to the
next track.
• Press the Down button (3) twice to listen
to the previous track.
When the Down button (3) is pressed
once, the track currently being played
will start from the beginning again.
Fast forwarding/Rewinding a track
• Hold down the Up button (2) to fast for-
ward the track.
• Hold down the Down button (3) to fast
rewind the track.
Random playback
Press the RDM button (5).
Each time the button is pressed, the mode
will change as follows:
• FOLDER RANDOM
The random indicator “F.RDM” will light.
The tracks in the current folder will be
played in random order.
• ALL RANDOM
The random indicator “RDM” will light.
The tracks in the loaded disc will be
played in random order.
Repeat playback
Press the RPT button (4).
Each time the button is pressed, the mode
will change as follows:
• FILE REPEAT
The repeat indicator “RPT” will light.
The track currently being played will be
played repeatedly.
• FOLDER REPEAT
The repeat indicator “F.RPT” will light.
All tracks in the currently selected folder
will be played repeatedly.
OFF FOLDER RANDOM ALL RANDOM
OFF FILE REPEAT FOLDER REPEAT
5-44
OTHER CONTROLS AND EQUIPMENT
Display change
Press the DISP button (6).
Each time the button is pressed, display
will change as follows:
NOTE:
• “NO TITLE” will be displayed when there
is no text information in the disc currently
being played.
• If text data contains more than 16 char-
acters, the “>” mark will appear at the
right end. Holding down the DISP button
(6) for 1 second or longer can display the
next page.
Notes on MP3/WMA/AAC
What is MP3?
• MP3 (MPEG audio layer3) is an audio
compression format that has become
the standard format among PC users. Its
merit is that the original audio data is
compressed to approximately 1/10 and
high sound quality is maintained. This
means that it is possible to store the data
of approximately 10 music CDs on a sin-
gle CD-R/RW disc, which in turn makes
it possible to play music for a long time
without having to change the disc.
What is WMA?
• An abbreviation of “Windows Media
Audio,” WMA is an audio compression
format developed by Microsoft.
• WMA files for which the DRM (Digital
Rights Management) function is ON can-
not be played.
• Windows Media
TM
and the Windows
®
logo are trademarks or registered trade-
marks of Microsoft Corporation in the
United States and other countries.
What is AAC?
• An abbreviation of “Advanced Audio
Coding,” AAC is an audio compression
format used by MPEG2 and MPEG4.
Points to remember when making MP3/
WMA/AAC files
Common
• High bit rate and high sampling fre-
quency are recommended for high qual-
ity sounds.
• Selecting VBR (Variable Bit Rate) is not
recommended. Selecting VBR may
cause display of incorrect playing time
and jumpiness of playback.
• Playback sound quality varies depend-
ing on the encoding environment. For
details, refer to the user manual of the
encoding software and the writing soft-
ware in use.
Recording MP3/WMA/AAC files on a CD
media
• It is recommended not to write both CD-
DA files and MP3/WMA/AAC files on a
disc.
• If both CD-DA files and MP3/WMA/AAC
files are on the same disc, tracks may
not be played in the correct order or
some tracks may not be played at all.
Play time
Folder name
File name
Album name (MP3, AAC only)
Track title
Artist name
NOTICE
Never assign the “.mp3”, “.wma”, or
“.m4a” file name extension to a file if
it is not in the MP3/WMA/AAC format
file. Failure to observe this may result
in damage to the speaker due to
noise production.
5-45
OTHER CONTROLS AND EQUIPMENT
• When storing both MP3 data and WMA
data on the same disc, sort and place
them in different folders.
• Do not write files other than MP3/WMA/
AAC files and unnecessary folders on a
disc.
• MP3/WMA/AAC files should be named
to meet the standards and the file sys-
tem specifications as shown below.
• The file extension “.mp3”, “.wma” or
“.m4a” should be assigned to files based
on their format independently.
• You may encounter a trouble in playing
MP3/WMA/AAC files or displaying infor-
mation of MP3/WMA/AAC files depend-
ing on the writing software or CD
recorder in use.
• This unit does not have a play list func-
tion.
• It is recommended to write discs in Disc-
at-Once mode even though Multi-ses-
sion mode is supported.
Compression formats
MP3
• Bit rate
:
MPEG1 Audio Layer III: 32 k - 320 kbps
MPEG2 Audio Layer III: 8 k - 160 kbps
MPEG2.5 Audio Layer III: 8 k - 160 kbps
• Sampling frequency
:
MPEG1 Audio Layer III: 32 k/44.1 k/
48 kHz
MPEG2 Audio Layer III: 16 k/22.05 k/
24 kHz
MPEG2.5 Audio Layer III: 8 k/11.025 k/
12 kHz
WMA (Ver. 7, Ver. 8, Ver. 9*)
• Bit rate: CBR 32 k - 320 kbps
• Sampling frequency: 32 k/44.1 k/48 kHz
* WMA 9 Professional/LossLess/Voice are
not supported.
AAC*
• Bit rate: ABR 16 k - 320 kbps
• Sampling frequency: 32 k/44.1 k/48 kHz
* Apple Lossless is not supported.
Supported file systems
ISO 9660 Level 1/Level 2, Joliet, Romeo
Maximum number of files/folders
• Maximum number of files: 512
• Maximum number of files in a folder: 255
• Maximum depth of tree structure: 8
• Maximum number of folders: 255
(Root folder is included.)
5-46
OTHER CONTROLS AND EQUIPMENT
Listening to files stored in a USB device
68PH00560
(6)
(1)
(7)
(5)
(4)
(2)
(3)
Display
(1) MEDIA button
(2) TUNE FOLDER PUSH SOUND knob
(3) Up button
(4) Down button
(5) RPT button
(6) RDM button
(7) DISP button
(A) Folder number
(B) Track number
(C) Play time
(D) File type
NOTICE
Do not connect any USB device other
than a USB memory or a USB audio
player. Do not connect multiple USB
devices to the USB connector using a
USB hub, etc. Supplying power to
multiple USB devices from the con-
nector could cause overheating and
smoking.
(C)
(B)(A)
(D)
5-47
OTHER CONTROLS AND EQUIPMENT
Selecting a USB device mode
Press the MEDIA button (1).
Each time the button is pressed, the mode
will change as follows:
Selecting a folder
Turn the TUNE FOLDER PUSH SOUND
knob (2) to select the desired folder.
Selecting a track
• Press the Up button (3) to listen to the
next track.
• Press the Down button (4) twice to listen
to the previous track.
When the Down button (4) is pressed
once, the track currently being played
will start from the beginning again.
Fast forwarding/Rewinding a track
• Hold down the Up button (3) to fast for-
ward the track.
• Hold down the Down button (4) to fast
rewind the track.
Random playback
Press the RDM button (6).
Each time the button is pressed, the mode
will change as follows:
• FOLDER RANDOM
The random indicator “F.RDM” will light.
The tracks in the currently selected
folder will be played in random order.
• ALL RANDOM
The random indicator “RDM” will light.
The tracks in the connected USB device
will be played in random order.
Repeat playback
Press the RPT button (5).
Each time the button is pressed, the mode
will change as follows:
• FILE REPEAT
The repeat indicator “RPT” will light.
The track currently being played will be
played repeatedly.
• FOLDER REPEAT
The repeat indicator “F.RPT” will light.
All the tracks in the folder currently
selected will be played repeatedly.
Display change
Press the DISP button (7).
Each time the button is pressed, display
will change as follows:
NOTE:
• “NO TITLE” will be displayed when there
is no text information in the disc currently
being played.
• If text data contains more than 16 char-
acters, the “>” mark will appear at the
right end. Holding down the DISP button
(7) for 1 second or longer can display the
next page.
USB (iPod
®
) (if equipped)
Bluetooth
®
audio (if equipped)
AUX (if equipped)
OFF FOLDER RANDOM ALL RANDOM
OFF FILE REPEAT FOLDER REPEAT
Play time
Folder name
File name
Album name (MP3, AAC only)
Track title
Artist name
5-48
OTHER CONTROLS AND EQUIPMENT
Notes on USB device
Compatible USB devices
• USB Mass Storage Class
For details as to whether your USB
memory/USB Audio is compatible with
USB Mass Storage Class, please con-
tact the USB memory/USB Audio manu-
facturer.
• USB Standard Compatibility 1.1/2.0 Full
Speed
• File System FAT12/16/32, VFAT
• Maximum current less than 1.0 A
• If devices such as USB hub, extension
cable are connected to the audio sys-
tem, it may not be recognized. In such
case connect the USB device directly to
the audio system.
• Devices such as MP3 player/Mobile
phone/digital camera may not be recog-
nized by the audio system for playing
music.
USB device connection
• When connecting a USB device, make
sure that the connector is pushed all the
way into the port.
• Do not leave the USB device for long
periods of time in places inside the vehi-
cle where the temperature can rise too
high.
• Back up any important data beforehand.
We cannot accept responsibility for any
lost data.
• It is recommended not to connect a USB
device that contains data files other than
MP3/WMA/AAC format.
Recording MP3/WMA/AAC files on a
USB device
• Playback or display may not be possible
depending on the type of USB device in
use or the condition of the recording.
• Depending on the connected USB mem-
ory, the files may be played in different
order from the order that the files were
stored.
Compression formats
MP3
• Bit rate
:
MPEG1 Audio Layer III: 32 k - 320 kbps
MPEG2 Audio Layer III: 8 k - 160 kbps
MPEG2.5 Audio Layer III: 8 k - 160 kbps
• Sampling frequency
:
MPEG1 Audio Layer III: 32 k/44.1 k/48 kHz
MPEG2 Audio Layer III: 16 k/22.05 k/24 kHz
MPEG2.5 Audio Layer III: 8 k/11.025 k/12 kHz
WMA (Ver. 7, Ver. 8, Ver. 9*)
• Bit rate: CBR 32 k - 320 kbps
• Sampling frequency: 32 k/44.1 k/48 kHz
* WMA 9 Professional/LossLess/Voice are
not supported.
AAC*
• Bit rate: ABR 16 k - 320 kbps
• Sampling frequency: 32 k/44.1 k/48 kHz
* Apple Lossless is not supported.
Maximum number of files/folders
• Maximum number of files: 2500
• Maximum number of files in a folder: 255
• Maximum depth of tree structure: 8
• Maximum number of folders: 255
(Root folder is included.)
5-49
OTHER CONTROLS AND EQUIPMENT
Listening to an iPod
®
68PH00565
(6)
(1)
(8)
(7)
(4)
(2)
(3)
(5)
Display
(1) MEDIA button
(2) TUNE FOLDER PUSH SOUND knob
(3) Up button
(4) Down button
(5) RPT button
(6) RDM button
(7) DISP button
(8) Preset buttons ([1] to [6])
(A) Track title
(B) Track number
(C) Play time
(C)
(A)
(B)
5-50
OTHER CONTROLS AND EQUIPMENT
Selecting an iPod
®
mode
Press the MEDIA button (1).
Each time the button is pressed, the mode
will change as follows:
Selecting a track
• Press the Up button (3) to listen to the
next track.
• Press the Down button (4) twice to listen
to the previous track.
When the Down button (4) is pressed
once, the track currently being played
will start from the beginning again.
Fast forwarding/Rewinding a track
• Hold down the Up button (3) to fast for-
ward the track.
• Hold down the Down button (4) to fast
rewind the track.
Random playback
Press the RDM button (6).
Each time the button is pressed, the mode
will change as follows:
• SONG RANDOM
The random indicator “RDM” will light.
The tracks in the iPod
®
will be played in
random order.
• ALBUM RANDOM
The random indicator “F.RDM” will light.
The albums in the iPod
®
will be played in
random order.
Repeat playback
Press the RPT button (5).
Each time the button is pressed, the mode
will change as follows:
• SONG REPEAT
The repeat indicator “RPT” will light.
The track currently being played will be
played repeatedly.
Display change
Press the DISP button (7).
Each time the button is pressed, display
will change as follows:
NOTE:
If text data contains more than 16 charac-
ters, the “>” mark will appear at the right
end. Holding down the DISP button (7) for
1 second or longer can display the next
page.
USB (iPod
®
) (if equipped)
Bluetooth
®
audio (if equipped)
AUX (if equipped)
OFF SONG RANDOM ALBUM RANDOM
OFF SONG REPEAT
Playlist name /
Track title (Playlist mode only)
Artist name /
Track title
Album name /
Track title
Track title /
Play time
5-51
OTHER CONTROLS AND EQUIPMENT
Playing Mode selection
1) Press the button numbered [1] of the
Preset buttons (8) for 1 second or lon-
ger.
2) Turn the TUNE FOLDER PUSH
SOUND knob (2).
Each time the knob is turned, the mode
will change as follows:
3) Press the TUNE FOLDER PUSH
SOUND knob (2) to select the desired
mode.
NOTE:
• When the button numbered [1] of the
Preset buttons (8) is pressed, the previ-
ous mode will be displayed.
Notes on iPod
®
Supported iPod
®
• iPod
®
touch (5th generation)
• iPod
®
touch (4th generation)
• iPod
®
touch (3rd generation)
• iPod
®
touch (2nd generation)
• iPod
®
touch (1st generation)
• iPod
®
classic
• iPod
®
nano (7th generation)
• iPod
®
nano (6th generation)
• iPod
®
nano (5th generation)
• iPod
®
nano (4th generation)
• iPod
®
nano (3rd generation)
• iPod
®
nano (2nd generation)
• iPod
®
nano (1st generation)
• iPhone
®
5S
• iPhone
®
5C
• iPhone
®
5
• iPhone
®
4S
• iPhone
®
4
• iPhone
®
3GS
• iPhone
®
3G
• iPhone
®
* Some functions may not be available
depending on the model of iPod
®
.
* iPod
®
is a trademark of Apple Inc., regis-
tered in the U.S. and other countries.
* iPhone
®
is a trademark of Apple Inc.,
registered in the U.S. and other coun-
tries.
* Apple is not responsible for the opera-
tion of this device or its compliance with
safety and regulatory standards.
iPod
®
connection
• Make sure to detach the iPod
®
after
pressing the engine switch to change the
ignition mode to LOCK. The iPod
®
may
not be shut down when it is being con-
nected and may result in battery deple-
tion.
• Please do not connect iPod
®
accesso-
ries such as an iPod
®
remote control or
headphones while connecting the iPod
®
with the unit. The unit may not operate
correctly.
PLAYLIST
ARTIST
ALBUM
SONGS
GENRE
5-52
OTHER CONTROLS AND EQUIPMENT
AUX Function
68PH00566
(1) MEDIA button
(1)
AUX connection
To listen to auxiliary audio sources (sold
separately) through the unit, follow the
instruction below.
1) Connect the auxiliary audio source to
the AUX/USB socket (separately
attached) with an AUX cable.
2) Press the MEDIA button (1).
Each time the button is pressed, the
mode will change as follows:
CAUTION
• Before connection, mute the unit,
and also keep the volume of the
auxiliary audio source within a
range that will not cause distortion.
• When the audio source is turned
off, noise may be emitted. Be sure
to turn off the unit or switch to
another mode before turning off the
audio source.
USB (iPod
®
) (if equipped)
Bluetooth
®
audio (if equipped)
AUX (if equipped)
5-53
OTHER CONTROLS AND EQUIPMENT
NOTE:
• Please consult your place of purchase
for details about whether a given auxil-
iary audio source can be connected and
the proper auxiliary cord to use.
• The volume and tone controls of the
auxiliary audio source can be adjusted
on the unit.
• In AUX mode, the volume setting is dif-
ferent from another mode.
5-54
OTHER CONTROLS AND EQUIPMENT
Bluetooth
®
Hands-Free (if equipped)
68PH00567
(1) TUNE FOLDER PUSH SOUND knob
(2) VOL PUSH POWER knob
(3) Preset buttons
(4) Back button
(5) Bluetooth
®
setup button (on control panel)
(2)
(4)
(1)
(5)
(3)
Bluetooth
Steering switch
68PH00568
68PH00569
(6) Bluetooth
®
setup button (on steering
wheel)
(7) Off Hook button
(8) On Hook button
(9) MUTE switch
(10) VOL switch
(6)
(7)
(8)
(10)
(9)
5-55
OTHER CONTROLS AND EQUIPMENT
Phone registration
NOTE:
• Up to 5 phones can be registered.
• To set up a new phone, disconnect the
audio player from the unit. Connect the
audio player again after phone setup is
completed if necessary.
• When failed to establish the pairing
within 120 seconds, the connecting
operation will be canceled. Please try
again or refer to the manual of the phone
in use for how to establish the pairing
with the phone.
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Blue-
tooth”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Pairing”,
and press the knob (1) to determine the
selection.
4) Select “MY CAR” from the Bluetooth
®
menu of the phone and establish the
pairing.
Refer to the manual of the phone in use
for further information.
5) Enter the Passkey displayed on the unit
to the phone.
6) When the pairing with the phone is
established, automatic transfer of the
phonebook and the call history
becomes selectable. The automatic
transfer starts with “Yes” and it does not
with “No”.
7) Press the On Hook button (8).
NOTE:
• When selecting “Go Back” or pressing
the back button (4), the previous menu
will be displayed.
• When additionally registering a phone,
operate the same step from 1).
Receiving a call
Press the Off Hook button (7) to receive a
call.
Ending a call
Press the On Hook button (8) to end a call.
Rejecting a call (only for supported
models)
Press the On Hook button (8) to reject a
incoming call.
Mute of Hands-free Microphone
Press the MUTE switch (9) to mute the
microphone. To cancel the mute, press the
MUTE switch (9) again.
Adjusting the listening volume
• Turn the VOL PUSH POWER knob (2)
during a call.
Turning it clockwise increases the vol-
ume; turning it counterclockwise
decreases the volume.
• Press the VOL switch (10) during a call.
Pressing “+” of the switch increases the
volume, pressing “-” of the switch
decreases the volume.
Adjusting the ring volume
• Turn the VOL PUSH POWER knob (2)
while a call coming in.
Turning it clockwise increases the vol-
ume; turning it counterclockwise
decreases the volume.
• Press the VOL switch (10) during a call.
Pressing “+” of the switch increases the
volume, pressing “-” of the switch
decreases the volume.
Adjusting the call or ringtone volume
Follow the instructions below to adjust the
call or ringtone volume.
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Tele-
phone”, and press the knob (1) to deter-
mine the selection.
To use the hands-free function with this
unit, it is required to register the phone
in advance.
5-56
OTHER CONTROLS AND EQUIPMENT
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Sound Set-
ting”, and press the knob (1) to deter-
mine the selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Call Vol-
ume” or “Ringtone Volume”, and press
the knob (1) to determine the selection.
The current call or ringtone volume will
be displayed.
5) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select desired call
or ringtone volume, and press the knob
(1) to determine the selection.
NOTE:
When selecting “Go Back” or pressing the
back button (4), the previous menu will be
displayed.
Dialing using Missed/Incoming/
Outgoing Calls
Follow the instructions below to dial to the
last dialed number again.
NOTE:
Up to 30 phone numbers of the latest calls
can be stored. (30 calls including missed,
received and dialed call)
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Tele-
phone”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “All Calls”,
“Missed Calls”, “Incoming Calls” or
“Outgoing Calls”, and press the knob
(1) to determine the selection.
To dial from the dialed history or the
received history, select “All Calls”,
“Missed Calls”, “Incoming Calls” or
“Outgoing Calls” respectively.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select the desired
number, and press the knob (1) to
determine the selection.
5) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Dial”, and
press the knob (1) or the Off Hook but-
ton (7) to dial to the selected number.
NOTE:
• When selecting “Go Back” or pressing
the back button (4), the previous menu
will be displayed.
• Pressing “Confirm” after selecting “Add
Speed Dial” can register the selected
number in the speed dial.
• Pressing “Confirm” after selecting
“Delete” can delete the selected number
from the call history.
Deletion of call history
Follow the instructions below to delete a
missed/incoming/outgoing call history.
1) Press the Bluetooth® setup button (5)
or (6). The Bluetooth® setup menu will
be displayed.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Tele-
phone”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup
Phonebook”, and press the knob (1) to
determine the selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Delete His-
tory”, and press the knob (1) to deter-
mine the selection.
5) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Missed
Calls”, “Incoming Calls”, or “Outgoing
Calls”, and press the knob (1) to deter-
mine the selection.
6) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select a number to
5-57
OTHER CONTROLS AND EQUIPMENT
be deleted or “ALL”, and press the knob
(1) to determine the selection.
7) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Delete?” or
“Delete All?”, and press the knob (1) to
determine the selection.
8) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Confirm”,
and press the knob (1) to complete the
deletion.
NOTE:
When selecting “Go Back” or pressing the
back button (4), the previous menu will be
displayed.
Registration in Phonebook
Registration of numbers in the phonebook.
Follow the instructions below to register
phone numbers in the Phonebook of the
unit.
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Tele-
phone”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup
Phonebook”, and press the knob (1) to
determine the selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Add Con-
tacts”, and press the knob (1) to deter-
mine the selection.
5) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Overwrite
All” or “Add One Contact”, and press
the knob (1) to determine the selection.
The “Rest of Memory XXXX: Ok?” will
be displayed.
6) Press or turn the TUNE FOLDER
PUSH SOUND knob (1) to select “Con-
firm”, and press the knob (1) to deter-
mine the selection.
7) Transfer contacts from the phone.
When the registration is completed, the
“Setup Phonebook” will be displayed.
NOTE:
• When selecting “Go Back” or pressing
the back button (4), the previous menu
will be displayed.
• Up to 1000 numbers can be registered in
Phonebook.
Transfer of call history (Call History)
Follow the instructions below to transfer
call history of the registered phone.
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Tele-
phone”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Call His-
tory”, and press the knob (1) to deter-
mine the selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Overwrite
call History”, and press the knob (1) to
determine the selection.
5) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Confirm”,
and press the knob (1) to transfer the
call history from the phone.
NOTE:
When selecting “Go Back” or pressing the
back button (4), the previous menu will be
displayed.
Automatic transfer of phonebook/call
history
You can select whether or not the device
transfers the phonebook and the call his-
tory automatically when the phone is regis-
tered. Follow the instructions below to
select.
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Tele-
phone”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “A.Transfer”,
and press the knob (1) to determine the
selection.
5-58
OTHER CONTROLS AND EQUIPMENT
4) Pressing the TUNE FOLDER PUSH
SOUND knob (1) switches between
“ On” and “ Off”.
NOTE:
Selecting “Go Back” or pressing the back
button (4) stores displayed setting and the
previous menu is displayed.
Making a call by Phonebook
Follow the instructions below to dial a num-
ber registered in Phonebook.
1) Press the Off Hook button (7).
The Bluetooth
®
phonebook menu will
be displayed.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Phone-
book”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select the initial of
the name you would like to make a call,
and press the knob (1) to determine the
selection.
The registered numbers will be dis-
played in sequence. If names have
been registered together with numbers,
the names will be displayed.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Dial”, and
press the knob (1) to determine the
selection.
5) Press the Off Hook button (7).
The displayed number or the contact
registered with the displayed name will
be dialed.
NOTE:
The system can only access the contacts
that are stored in the phone memory.
Deletion of registered data (Delete
Entry)
Follow the instructions below to delete a
number registered in Phonebook.
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Tele-
phone”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup
Phonebook”, and press the knob (1) to
determine the selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Delete Con-
tacts”, and press the knob (1) to deter-
mine the selection.
5) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select a contact to
be deleted, and press the knob (1) to
determine the selection.
6) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Delete?”,
and press the knob (1) to determine the
selection.
7) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Confirm”,
and press the knob (1) to complete the
deletion.
NOTE:
When selecting “Go Back” or pressing the
back button (4), the previous menu will be
displayed.
Registration in speed dial
Follow the instructions below to assign a
number to one of the Preset buttons to use
as the speed dial.
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Tele-
phone”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup
Phonebook”, and press the knob (1) to
determine the selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Add Speed
Dial”, and press the knob (1) to deter-
mine the selection.
5) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select a contact to
be assigned, and press the knob (1) to
determine the selection.
6) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Choose
5-59
OTHER CONTROLS AND EQUIPMENT
Preset”, and press the knob (1) to
determine the selection.
7) Press one of the Preset buttons (3) to
which the selected contact is to be
assigned. If a contact is already
assigned to the selected button, a con-
firmation message will be displayed.
Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Overwrite”,
and press the knob (1) to complete the
selection.
8) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Confirm”,
and press the knob (1) to complete the
assignment.
When the assignment is completed, the
“Setup Phonebook” will be displayed.
NOTE:
When selecting “Go Back” or pressing the
back button (4), the previous menu will be
displayed.
Registration in speed dial (Alternate
Method)
1) Press the Off Hook button (7).
The Bluetooth
®
phonebook menu will
be displayed.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “All Calls”,
”Missed Call” or “Outgoing Call”, and
press the knob (1) to determine the
selection. To select a contact / number
to be assigned from the dialed history
or the received history, select “All Calls”
,“Missed Call”, “Incoming Calls “or “Out-
going Calls” respectively.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select desired con-
tact/number, and press the knob (1) to
determine the selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Add to
speed dials”, and press the knob (1) to
assign to the selected contact/number.
5) Press one of the Preset buttons (3) to
which the selected contact is to be
assigned. If a number is already
assigned to the selected button, a con-
firmation message will be displayed.
Turn the TUNE FOLDER PUSSH
SOUND knob (1) to select “Overwrite?”,
and press the knob (1) to determine the
selection.
6) Turn the TUNE FOLDER PUSSH
SOUND knob (1) to select “Confirm”,
and press the knob (1) to complete the
assignment.
NOTE:
When selecting “Go Back” or pressing the
back button (4), the previous menu will be
displayed.
One-touch call (Speed dial)
Follow the instructions below to dial the
number assigned to each of the Preset
buttons (3).
1) Press the Off Hook button (7).
The Bluetooth
®
phonebook menu will
be displayed.
Pressing one of the Preset buttons (3)
can skip step 2) and the 1st line of step
3).
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Speed
Dials”, and press the knob (1) to deter-
mine the selection.
3) Press one of the Preset buttons (3).
The assigned number/contact will be
displayed. When no number is
assigned, “No Entry” is displayed.
4) Press the Off Hook button (7).
The selected number will be dialed.
5-60
OTHER CONTROLS AND EQUIPMENT
Deletion of speed dial (Del Speed Dial)
To delete a number assigned for the speed
dial, follow the instructions below.
1) Press the Off Hook button (7).
The Bluetooth
®
phonebook menu will
be displayed.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Speed
Dials”, and press the knob (1) to deter-
mine the selection.
3) Press one of the Preset buttons (3) to
which the number to be deleted is
assigned.
“No Entry” appears if the number is not
registered.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Delete”, and
press the knob (1) to determine the
selection.
5) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Del Speed
Dial”, and press the knob (1) to deter-
mine the selection.
6) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Confirm”,
and press the knob (1) to complete the
deletion.
NOTE:
When selecting “Go Back” or pressing the
back button (4), the previous menu will be
displayed.
Display of device data (Device Name)
Follow the instructions below to display the
BD (Bluetooth
®
Device) address and
device name.
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Blue-
tooth”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Bluetooth
Info”, and press the knob (1) to deter-
mine the selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Device
Name” or “Device Address”, and press
the knob (1) to display the device name
or the BD (Bluetooth
®
Device) address.
NOTE:
When selecting “Go Back” or pressing the
back button (4), the previous menu will be
displayed.
Reset to the factory defaults
Follow the instructions below to reset all
the settings to the factory defaults.
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Blue-
tooth”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Initialize”,
and press the knob (1) to determine the
selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “All Initial-
ize”, and press the knob (1) to deter-
mine the selection.
5) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Confirm”,
and press the knob (1) to start the
reset.
NOTE:
When selecting “Go Back” or pressing the
back button (4), the previous menu will be
displayed.
5-61
OTHER CONTROLS AND EQUIPMENT
Selection of phone (Select Phone)
Follow the instructions below to select a
phone to be paired with from the registered
phones.
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Blue-
tooth”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “List Phone”,
and press the knob (1) to determine the
selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select a phone to
be paired with, and press the knob (1)
to determine the selection.
5) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Select”, and
press the knob (1) to determine the
selection.
NOTE:
• When selecting “Go Back” or pressing
the back button (4), the previous menu
will be displayed.
• The Bluetooth
®
ready audio device will
be disconnected when the phone is
selected.
List of phones (List Phones)
Follow the instructions below to display the
names of the registered phones in
sequence.
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Blue-
tooth”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “List Phone”,
and press the knob (1) to determine the
selection.
The names of the registered phones
are displayed in sequence.
NOTE:
When selecting “Go Back” or pressing the
back button (4), the previous menu will be
displayed.
Passkey setting (Set Passkey)
Follow the instructions below to set the
security number (Passkey).
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Blue-
tooth”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Passkey”,
and press the knob (1) to determine the
selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “New Pass-
key”, and press the knob (1) to deter-
mine the selection.
5) Press or turn the TUNE FOLDER
PUSH SOUND knob (1) to select “Con-
firm”.
6) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select a number for
the first digit, and press the knob (1) to
determine the selection. Select and
determine numbers for the second,
third and fourth digits in order in the
same manner. When not entering up to
the eighth digit, enter blanks for the
successive digits.
7) Turn the TUNE FOLDER PUSH
SOUND knob (1) to determine the
passkey setting.
NOTE:
When selecting “Go Back” or pressing the
back button (4), the previous menu will be
displayed.
5-62
OTHER CONTROLS AND EQUIPMENT
Deletion of phone information (Delete
Phone)
Follow the instructions below to delete the
registered information of the phone.
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Blue-
tooth”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “List Phone”,
and press the knob (1) to determine the
selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select a phone to
be deleted, and press the knob (1) to
determine the selection.
5) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Delete
Phone”, and press the knob (1) to
determine the selection.
6) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Delete?”,
and press the knob (1) to determine the
selection.
7) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Confirm”,
and press the knob (1) to determine the
selection.
NOTE:
When selecting “Go Back” or pressing the
back button (4), the previous menu will be
displayed.
BT function on/off (BT Power)
Follow the instructions below to turn on/off
the Bluetooth
®
function.
1) Press the Bluetooth
®
setup button (5)
or (6).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “Setup Blue-
tooth”, and press the knob (1) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (1) to select “BT Power”,
and press the knob (1) to determine the
selection.
4) Press the TUNE FOLDER PUSH
SOUND knob (1) to select “BT Power
On” or “BT Power Off”.
NOTE:
• When the BT function is turned off, the
connection between this unit and the
registered phone in use will be discon-
nected.
• When selecting “Go Back” or pressing
the back button (4), the previous menu
will be displayed.
5-63
OTHER CONTROLS AND EQUIPMENT
Bluetooth
®
audio (if equipped)
68PH00570
(1)
(2)
(4)
(3)
(5)
(6)
(7)
Bluetooth
Steering switch
68PH00571
Display
(1) MEDIA button
(2) TUNE FOLDER PUSH SOUND knob
(3) Up button
(4) Down button
(5) DISP button
(6) Back button
(7) Bluetooth
®
setup button (on control
panel)
(8) Bluetooth
®
setup button (on steering
wheel)
(A) Track number
(B) Play time
(8)
(B)
(A)
5-64
OTHER CONTROLS AND EQUIPMENT
Registration of audio devices
NOTE:
• To set up a new audio player, disconnect
the phone from the unit. Connect the
phone after audio player setup is com-
pleted if necessary.
• When failed to establish the connection
within 120 seconds, the connecting
operation will be canceled. Please try
again or refer to the audio player manual
for assistance with the pairing process.
1) Press the Bluetooth
®
setup button (7)
or (8).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Setup Blue-
tooth”, and press the knob (2) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Pairing”,
and press the knob (2) to determine the
selection.
4) Select “My Car” from the Bluetooth
®
menu of the audio player and establish
the pairing.
Refer to the manual of the audio player
in use for further information.
5) Enter the Passkey displayed on the unit
to the audio player.
NOTE:
• When selecting “Go Back” or pressing
the back button (6), the previous menu
will be displayed.
• When additionally registering audio
devices, operate the same step from 1).
Selecting the Bluetooth
®
audio mode
Press the MEDIA button (1).
Each time the button is pressed, the mode
will change as follows:
Selecting a group (only for supported
models)
Turn the TUNE FOLDER PUSH SOUND
knob (2) to select a group.
Selecting a track
• Press the Up button (3) to listen to the
next track.
• Press the Down button (4) twice to listen
to the previous track.
When the Down button (4) is pressed
once, the track currently being played
will start from the beginning again.
Fast forwarding/Rewinding a track
• Hold down the Up button (3) to fast for-
ward the track.
• Hold down the Down button (4) to fast
rewind the track.
NOTE:
Some functions may not be available
depending on Bluetooth
®
audio.
Display change
Press the DISP button (5).
Each time the button is pressed, display
will change as follows:
NOTE:
If text data contains more than 16 charac-
ters, the “>” mark will appear at the right
end. Holding down the DISP button (5) for
1 second or longer can display the next
page.
To use Bluetooth
®
ready audio devices
with this unit, it is required to register the
devices.
USB (iPod
®
) (if equipped)
Bluetooth
®
audio (if equipped)
AUX (if equipped)
Play time
Track name
Artist name
Album name
5-65
OTHER CONTROLS AND EQUIPMENT
Selection of audio device (Select Audio)
Follow the instructions below to select an
audio device to be paired with from the
registered audio devices.
1) Press the Bluetooth
®
setup button (7)
or (8).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Setup Blue-
tooth”, and press the knob (2) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “List Audio”,
and press the knob (2) to determine the
selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select an audio
device to be used, and press the knob
(2) to determine the selection.
5) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Select”, and
press the knob (2) to determine the
selection.
6) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Confirm”,
and press the knob (2) to complete the
pairing.
NOTE:
• When selecting “Go Back” or pressing
the back button (6), the previous menu
will be displayed.
• The phone will be disconnected when
the Bluetooth
®
ready audio device is
selected.
List of audio devices (List Audio)
Follow the instructions below to display the
names of the registered audio devices in
sequence.
1) Press the Bluetooth
®
setup button (7)
or (8).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Setup Blue-
tooth”, and press the knob (2) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “List Audio”,
and press the knob (2) to determine the
selection. The names of registered
audio devices will be displayed in
sequence.
NOTE:
When selecting “Go Back” or pressing the
back button (6), the previous menu will be
displayed.
Passkey setting (Set Passkey)
Follow the instructions below to set the
security number (Passkey).
1) Press the Bluetooth
®
setup button (7)
or (8).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Setup Blue-
tooth”, and press the knob (2) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Passkey”,
and press the knob (2) to determine the
selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “New Pass-
key”, and press the knob (2) to deter-
mine the selection.
5) Press or turn the TUNE FOLDER
PUSH SOUND knob (2) to select “Con-
firm”.
6) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select a number for
the first digit, and press the knob (2) to
determine the selection. Select and
determine numbers for the second,
third and fourth digits in order in the
same manner. When not entering up to
the eighth digit, enter blanks for the
successive digits.
7) Turn the TUNE FOLDER PUSH
SOUND knob (2) to determine the
passkey setting.
NOTE:
When selecting “Go Back” or pressing the
back button (6), the previous menu will be
displayed.
5-66
OTHER CONTROLS AND EQUIPMENT
Deletion of audio device information
(Delete Audio)
Follow the instructions below to delete the
registered information of audio device.
1) Press the Bluetooth
®
setup button (7)
or (8).
The Bluetooth
®
setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Setup Blue-
tooth”, and press the knob (2) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “List Audio”,
and press the knob (2) to determine the
selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select an audio
device to be deleted, and press the
knob (2) to determine the selection.
5) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Delete”, and
press the knob (2) to determine the
selection.
6) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Delete?”,
and press the knob (2) to determine the
selection.
7) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Confirm”,
and press the knob (2) to complete the
deletion.
NOTE:
When selecting “Go Back” or pressing the
back button (6), the previous menu will be
displayed.
Disclaimer for Bluetooth
®
function
• Depending on the mobile phone models,
some phones may not be compatible
fully or partially (some function may be
restricted).
• Connectivity or voice quality may get
affected depending on circumstances.
• After the ignition switch is turned to the
“ON” position, the audio system takes
few seconds to detect and connect to
the Bluetooth
®
device (if already paired).
Remote Audio Controls
(if equipped)
Controlling of basic functions of the audio
system is available using the switches on
the steering wheel.
68PH00572
(1)
(2) (3)
(4)
5-67
OTHER CONTROLS AND EQUIPMENT
Adjusting the volume
• To increase the volume, hold down “+” of
the VOL switch (1). The volume will keep
on being increased until the switch is
released.
• To decrease the volume, hold down “-” of
the VOL switch (1). The volume will keep
on being decreased until the switch is
released.
• To mute the sound, press the switch (2).
Selecting the mode
Press the switch (3).
Each time the button is pressed, the mode
will change as follows:
It is possible to turn on the audio system
by pressing the switch (3).
Selecting the radio station (FM1, FM2,
AM mode)
• To select the next preset station, press
“ ” of the switch (4) only for a moment.
• To select the previous preset station,
press “ ” of the switch (4) only for a
moment.
• To scan a higher frequency radio station,
press “ ” of the switch (4) for 1 second
or longer.
• To scan a lower frequency radio station,
press “ ” of the switch (4) for 1 second
or longer.
Selecting the track (CD, USB (iPod
®
),
Bluetooth
®
audio mode)
• To skip to the next track, press “ ” of the
switch (4) only for a moment.
• To skip to the previous track, press “ ” of
the switch (4) twice only for a moment.
When the switch (4) is pushed down
once only for a moment, the track cur-
rently being played will start from the
beginning again.
Fast forwarding/Rewinding a track
• To fast forward, press “ ” of the switch
(4) for 1 second or longer.
• To fast rewind, press “ ” of the switch (4)
for 1 second or longer.
FM1 (Radio)
FM2 (Radio)
CD
Bluetooth
®
audio (if equipped)
AUX (if equipped)
USB (iPod
®
) (if equipped)
AM (Radio)
<
<
<
<
<
<
<
<
5-68
OTHER CONTROLS AND EQUIPMENT
Anti-Theft Feature
68PH00573
(1)
(4)
(3)
(2)
(1) VOL PUSH POWER knob
(2) Preset buttons ([1] to [6])
(3) Up button
(4) TUNE FOLDER PUSH SOUND knob
5-69
OTHER CONTROLS AND EQUIPMENT
The anti-theft function is intended to dis-
courage thefts, such as that the audio sys-
tem becomes inoperable when it is
installed on other vehicles.
This function works by entering a Personal
Identification Number (PIN).
When the unit is disconnected from its
power source, such as when the audio
system is removed or the battery is discon-
nected, the unit will become inoperable
until the PIN is reentered.
Setting the Anti-Theft Function
1) Press the VOL PUSH POWER knob (1)
to power off.
2) Hold down the buttons numbered [1]
and [6] of the Preset buttons (2) and
press the VOL PUSH POWER knob (1).
“SECURITY” will be displayed.
3) Press the Up button (3) and the button
numbered [1] of the Preset buttons (2)
simultaneously.
4) Enter a 4-digit number to be registered
as PIN using the buttons numbered [1] -
[4] of the Preset buttons (2).
5) Hold down the TUNE FOLDER PUSH
SOUND knob (4) for 1 second or longer
to set the anti-theft function.
NOTE:
Take a note of the registered PIN and keep
it for the future use.
Canceling the anti-theft feature
To cancel the anti-theft function, delete the
registered PIN.
1) Press the VOL PUSH POWER knob (1)
to power off.
2) Hold down the buttons numbered [1]
and [6] of the Preset buttons (2) and
press the VOL PUSH POWER knob (1).
“PIN ENTRY” will be displayed.
3) Press the Up button (3) and the button
numbered [1] of the Preset buttons (2)
simultaneously.
4) Enter a 4-digit number to be registered
as PIN using the buttons numbered [1] -
[4] of the Preset buttons (2).
5) Hold down the TUNE FOLDER PUSH
SOUND knob (4) for 1 second or longer
to delete the registered PIN. The indi-
cation “----” will be displayed and the
anti-theft function will be canceled.
NOTE:
To change your PIN, first delete your cur-
rent PIN, then set a new one.
Confirming the Personal Identification
Number (PIN)
When the main power source is discon-
nected such as when the battery is
replaced, etc, it is required to enter the PIN
to make the unit operable again.
1) Set the ignition switch to the “ACC”
position.
“SECURITY” will be displayed.
2) Press the Up button (3) and the button
numbered [1] of the Preset buttons (2)
simultaneously.
3) Enter a 4-digit number to be registered
as PIN using the buttons numbered [1] -
[4] of the Preset buttons (2).
4) Hold down TUNE FOLDER PUSH
SOUND knob (4) for 1 second or lon-
ger.
When the PIN same as registered is
entered, the power of the audio system
will be turned off automatically and it
will become operable again.
NOTE:
If an incorrect PIN is entered, “ERROR”
and the total number of incorrect entry
attempts will be displayed.
If an incorrect PIN is entered 10 times,
“HELP” will be displayed and the audio
system will become inoperable.
5-70
OTHER CONTROLS AND EQUIPMENT
Battery Installation
Install a lithium battery (CR2025) with the poles facing the correct direction.
68PM5001
Battery replacement timing
• When battery power is depleted, the button may not be operable. If the remote controller
does not operate, replace the battery and check the operation.
Caution on battery
• Be sure to follow the instructions to prevent battery leakage, over-heating, ignition or
explosion.
If battery leakage has occurred, wipe the
container first then install a new battery. If
the battery solution contacts the skin, wash
off with water completely.
WARNING
• Do not expose the battery to flame.
Do not short circuit, disassemble,
or heat the battery.
• Do not charge the battery.
• Use the specified type battery.
• Keep the button-shaped battery
away from children to prevent acci-
dental swallowing.
If the battery is swallowed, contact a
doctor immediately.
CAUTION
• Install the battery with the poles
facing the correct direction.
• When not in use for a long period
of time, or if the battery is dead,
remove the battery from the remote
controller.
5-71
OTHER CONTROLS AND EQUIPMENT
Caution on Remote Controller
• Do not leave the remote controller in an
area exposed to direct sunlight, such as
on the dashboard or steering wheel. The
remote controller may deform because
of the heat, (Be especially careful of the
dashboard exposed to direct sunlight in
the summer, as it will become extremely
hot).
• When the vehicle is parked in an area
exposed to direct sunlight, Ensure the
remote controller is placed in an area not
exposed to direct sunlight. For example:
Glove box.
Under direct sunlight, signal reception
from the remote controller weakens. If
this happens, hold the remote controller
close to the signal receptor on the front
panel.
5-72
OTHER CONTROLS AND EQUIPMENT
Remote Controller
Common operations
In Sound Mode
Press to adjust the sound.(bass/treble/balance/fader)
In Preset-EQ Mode
The Preset-EQ setting switches as follows:
In AVC Mode
The AVC setting switches
as follows:
TUNE FOLDER UP/DOWN button
OFF (FLAT)
JAZZ
ROCK
POP
CLASSIC
HIP-HOP
OFF
LEVEL 1
LEVEL 2
LEVEL 3
Power ON / OFF
POWER button
Press to adjust volume.
(including at AUX mode)
VOLUME button
Press to mute the sound. Press it again to cancel
the mute.
MUTE button
While playback, the sound
mode switches as follows
(including at AUX mode,
except while displaying
iPod
®
menu):
SOUND button
Preset-EQ
BASS
TREBLE
BALANCE
FADER
AVC
The mode switches as
follows:
MODE button
FM1
FM2
CD
Bluetooth
®
audio
(if equipped)
AUX (if equipped)
USB (iPod
®
)
(if equipped)
AM
5-73
OTHER CONTROLS AND EQUIPMENT
Radio operations
NOTE:
When there are fewer than 6 stations that can be stored even if 1 round of auto store operation is performed, no station will be
stored at the remaining preset buttons.
Press to return to the last received fre-
quency in the previous auto store mode.
Press it for 2 seconds or longer. It selects
the stations with the stronger signals and
stores them in order.
AS button
Press to select the radio station.
SEEK TRACK UP/DOWN button
Press to select the desired preset station.
PRESET buttons (1-6)
5-74
OTHER CONTROLS AND EQUIPMENT
CD operations
Press to play the current track randomly.
Press it again to cancel.
RDM button
Press to plays the current track repeatedly.
Press it again to cancel.
RPT button
Press to skip to the next/previous track.
Press it for 1 second or longer to fast-forward/
fast-rewind the track.
SEEK TRACK UP/DOWN button
The display switches as follows:
Press it for 1 second or longer to display the
next page.
DISP button
Play time
Disc title
Track title
5-75
OTHER CONTROLS AND EQUIPMENT
MP3/WMA/AAC Disc operations
The repeat mode switches as follows:
RPT button
OFF
FILE REPEAT
FOLDER REPEAT
The display switches as follows:
Press it for 1 second or longer to display the next
page.
DISP button
Play time
Folder name
File name
Album name (MP3, AAC only)
Track title
Artist name
Press to skip to the next/previous track.
Press it for 1 second or longer to fast-forward/fast-
rewind the track.
SEEK TRACK UP/DOWN button
The random mode switches as follows:
RDM button
OFF
FOLDER RANDOM
ALL RANDOM
Press to skip to the next/previous folder.
TUNE FOLDER UP/DOWN button
5-76
OTHER CONTROLS AND EQUIPMENT
USB operations
The repeat mode switches as follows:
RPT button
OFF
FILE REPEAT
FOLDER REPEAT
The display switches as follows:
Press it for 1 second or longer to display the next
page.
DISP button
Play time
Folder name
File name
Album name (MP3, AAC only)
Track title
Artist name
Press to skip to the next/previous folder.
TUNE FOLDER UP/DOWN button
Press to skip to the next/previous file.
Press it for 1 second or longer to fast-forward/fast-
rewind the file.
SEEK TRACK UP/DOWN button
The random mode switches as follows:
RDM button
OFF
FOLDER RANDOM
ALL RANDOM
5-77
OTHER CONTROLS AND EQUIPMENT
iPod
®
operations
The random mode switches as follows:
RDM button
OFF
SONG RANDOM
ALBUM RANDOM
Press to play the current track repeatedly.
Press it again to cancel.
RPT button
The display switches as follows:
Press it for 1 second or longer to display the next
page.
DISP button
Playlist name /
Track title (Playlist mode only)
Artist name / Track title
Album name / Track title
Track title / Play time
While displaying iPod
®
menu, press to select the
desired item and display the list. When a track is
selected from the list, the playback starts.
ENT button
During playback
• Press to display iPod
®
menu.
• Press it for 1 second or longer to display the top menu.
While iPod
®
menu is displayed
• Press to display the folder in one layer upper.
• Press it for 1 second or longer to display the top menu.
MENU button
While displaying iPod
®
menu, press to dis-
play the next/previous list in the same layer.
TUNE FOLDER UP/DOWN button
Press to skip to the next/previous file.
Press it for 1 second or longer to fast-forward/fast-
rewind the file.
SEEK TRACK UP/DOWN button
5-78
OTHER CONTROLS AND EQUIPMENT
Troubleshooting
When encountered a problem, check and follow the instructions as described below.
If the described suggestions do not solve the problem, it is recommended to take the unit to your authorised Maruti Suzuki workshop.
Problem Possible cause Possible solution
Common
Unable to operate The security function is on.
When “SECURITY” is displayed, enter
the ID.
When “HELP” is displayed, contact your
authorised Maruti Suzuki workshop.
Unable to turn on the power (no sound).
(No sound is produced)
Fuse is blown.
Contact your authorised Maruti Suzuki
workshop.
Radio
Much noise
It may not be exactly tuned in to the sta-
tion.
Tune it in exactly to the station.
Unable to receive by auto tuning
There may be no station emitting signals
powerful enough.
Pick up a station by manual tuning.
CD
Sound skips or noise produced
The disc is dirty. Wipe the disc with a soft cloth.
The disc has a major scratch or is
warped.
Replace the disc with the one with no
scratch and also not warped.
5-79
OTHER CONTROLS AND EQUIPMENT
MP3/WMA/AAC
No playback
The disc contains unsupported formatted
data.
Check the file format.
Sound skips or noise produced
Sound skipping may occur when playing
VBR (Variable Bit Rate) files.
It is not recommended to play VBR files.
USB
Playback does not start when the USB
device is connected.
There is no supported format file to play
on this unit.
Check the file format.
The current consumption of the USB
device exceeds 1.0 A.
Use an USB device with a current con-
sumption lower than 1.0 A.
Bluetooth
®
Pairing failed
The distance between this unit and the
Bluetooth
®
ready device is too far, or a
metallic object may be located between
the Bluetooth
®
ready device and this unit.
Change the location of the Bluetooth
®
ready device.
The Bluetooth
®
function of the Blue-
tooth
®
ready device is off.
Refer to the manual of the Bluetooth
®
ready device. (Some devices have the
power saving function that automatically
activates after a certain time.)
Unable to receive a call.
Your current location may be out of ser-
vice area.
Drive your vehicle to the service area of
the phone.
The voice quality of hands-free is low
(Distortion, noise etc.).
Another wireless device may be located
near the unit.
Switch off the wireless device or keep it
away from the unit.
Problem Possible cause Possible solution
5-80
OTHER CONTROLS AND EQUIPMENT
Error Display Messages
Display Possible cause Possible solution
CD
ERROR 1 The disc cannot be read.
Insert the disc with its label side up.
Check the disc if it is not warped or is free of flaws.
When ERROR 1 does not disappear even when a nor-
mal disc is inserted, contact your authorised Maruti
Suzuki workshop.
ERROR 3
The player developed an error of an
unidentified cause.
When the CD is in the unit, press the CD eject button to
remove the disc.
When the disc cannot be ejected, contact your autho-
rised Maruti Suzuki workshop.
USB/iPod
®
ERROR 1 The USB device is disconnected. Check the connection of the USB device.
ERROR 2
Impossible to communicate correctly with
the USB device.
Unplug the USB device and plug it again.
Check the USB device.
ERROR 3 Inoperable due to an unidentified cause.
Unplug the USB device and plug it again.
When ERROR 3 does not disappear, contact your autho-
rised Maruti Suzuki workshop.
ERROR 4
The current consumption of the USB
device exceeds 1.0 A.
Check the USB device.
5-81
OTHER CONTROLS AND EQUIPMENT
Bluetooth
®
ERROR 1
The player developed an error of an
unidentified cause.
Disconnect the Bluetooth
®
ready device and connect it
again.
When ERROR 1 does not disappear, contact your autho-
rised Maruti Suzuki workshop.
Connection
Failed
Failed to establish pairing or connection Try to establish the pairing or connection again.
Memory Full
Reached the limit for the number of phone-
book data in transfer
Delete registered data of unnecessary number in phone-
book and try to transfer the register phone numbers in
the phonebook again.
Not Available Inoperable during driving Operate the system after pulling over your car.
Display Possible cause Possible solution

Related Topics

Other Controls and Equipment
Fuel Filler Cap Engine Hood Sun Visor Interior Light Accessory Socket AUX/USB Socket (if equipped) Assist Grips Glove Box Cup Holder and Storage Area Footrest Floor Mats (if equipped) Luggage Compartment Hook Luggage Compartment Cover Frame Hooks Heating and Air Conditioning System Manual Heating and Air Conditioning System Automatic Heating and Air Conditioning System (Climate Control) Radio Antenna Installation of Radio Frequency Transmitters

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot