Get Inspection and Maintenance -> Bulb replacement Guide for Suzuki Ignis SUV First Generation (2000-2008)

7-26

INSPECTION AND MAINTENANCE

81A283

Headlight aiming

Since special procedures are required, ask

your authorised Maruti Suzuki workshop

for this job.

Bulb replacement

Interior light

Remove the lens by using a flat-bladed

screwdriver covered with a soft cloth as

shown. To install it, simply push it back in.

Front

76MH0A139

WARNING

Always replace a blown fuse with a

fuse of the correct amperage. Never

use a substitute such as aluminum

foil or wire to replace a blown fuse. If

you replace a fuse and the new one

blows in a short period of time, you

may have a major electrical problem.

Have your vehicle inspected immedi-

ately by your authorised Maruti

Suzuki workshop.

BLOWNOK

EXAMPLE

CAUTION

• Light bulbs can be hot enough to

burn your finger right after turning

off lights. This is true especially for

halogen headlight bulbs. Replace

the bulbs after they become cool

enough.

• The halogen headlight bulbs are

filled with pressurized halogen gas.

They can burst and injure you if

they are hit or dropped. Handle

them carefully.

• To avoid injury by sharp-edged

parts of the body, wear gloves and

a long-sleeved shirt when replacing

light bulbs.

NOTICE

• The oils from your skin may cause

a halogen bulb to overheat and

burst when the lights are on. Grasp

a new bulb with a clean cloth.

• During bulb replacement, always

use same bulb number as used in

the vehicle.

NOTICE

Frequent bulb replacement indicates

the need for an inspection of the elec-

trical system. This should be carried

out by your authorised Maruti Suzuki

workshop.

EXAMPLE

7-27

INSPECTION AND MAINTENANCE

Luggage compartment (if equipped)

81PN162

Courtesy light (if equipped)

66RH140

Headlights

LED headlights (if equipped)

Since special procedures are required, we

recommend you take your vehicle to your

authorised Maruti Suzuki workshop for

bulb replacement.

Halogen headlights (if equipped)

66RH151

1) Open the engine hood. Disconnect the

coupler (1). Remove the sealing rubber

(2).

75RM068S

2) Push the retaining spring (3) forward

and unhook it. Then remove the bulb.

Install a new bulb in the reverse order

of removal.

75RM069

NOTE:

You can see the position of retaining spring

from the hole (4) of headlight.

EXAMPLE

(1)

(2)

EXAMPLE

(3)

EXAMPLE

(4)

EXAMPLE

7-28

INSPECTION AND MAINTENANCE

Front fog light (if equipped)

1) Start the engine. Turn the steering

wheel to the opposite side of the fog

light to be replaced to replace the bulb

easily. Then turn off the engine.

75RM094

2) Remove the clip (1) by prying it off with

a flat-bladed screwdriver as shown in

the illustration.

68PH00736

3) Open the end of the cover inside the

fender. Disconnect the coupler by push-

ing the lock release. Turn the bulb

holder counterclockwise and remove it.

Other general lights

Bulb holder

54G123

(1) Removal

(2) Installation

To remove a bulb holder from a light hous-

ing, turn the holder counterclockwise and

pull it out. To install the holder, push the

holder in and turn it clockwise.

(1)

EXAMPLE

(1)

(2)

EXAMPLE

7-29

INSPECTION AND MAINTENANCE

Bulb

54G124

(3) Removal

(4) Installation

There are two types of bulb, full glass type

(1) and glass/metal type (2).

To remove and install a full glass type bulb

(1), simply pull out or push in the bulb.

To remove a glass metal type bulb (2) from

a bulb holder, push in the bulb and turn it

counterclockwise. To install a new bulb,

push it in and turn it clockwise.

You can access the individual bulb or bulb

holders as follows.

Front turn signal light (1)

Front position light (2)

Models with halogen headlights

75RM066

Models with LED headlights

62R0306

Side turn signal light (if equipped)

68PH00729

1) Remove the light housing (1) by sliding

to left with your finger.

68PH00760

2) Turn the bulb holder (2) clockwise and

pull it out from the light housing.

(1)

(2)

(3)

(4)

EXAMPLE

(1)

(2)

EXAMPLE

(1)

EXAMPLE

(1)

EXAMPLE

(2)

EXAMPLE

7-30

INSPECTION AND MAINTENANCE

Rear combination light

75RM070

Remove the bolts (1) and pull the light

housing (2) straight.

NOTE:

When reinstalling the light housing, check

that the clips (3) are properly attached.

Reversing light

62R0122

1) Open the tailgate and remove the trim

(1) of the tailgate.

• Insert a flat blade screwdriver cov-

ered with a soft cloth between the trim

and the tailgate to make a space for

fingers, and then pull out the trim with

your fingers.

62R0378

2) Disconnect the coupler (2) by pushing

the lock release. Turn the bulb holder of

the reversing light (3) counterclockwise

and remove it.

(3)

(2)

(1)

EXAMPLE

(1)

EXAMPLE

(2)

(3)

EXAMPLE

7-31

INSPECTION AND MAINTENANCE

License plate light

75RM071

Wiper blades

54G129

If the wiper blades become brittle or dam-

aged, or make streaks when wiping,

replace the wiper blades.

To install new wiper blades, follow the pro-

cedures below.

NOTE:

Some wiper blades may be different from

the ones described here depending on

vehicle specifications. If so, consult your

authorised Maruti Suzuki workshop for

proper replacement method.

For windshield wipers:

70G119

1) Hold the wiper arm away from the win-

dow.

NOTE:

When raising both of the front wiper arms,

pull the driver’s side wiper arm up first.

When returning the wiper arms, lower the

passenger’s side wiper arm first.

Otherwise, the wiper arms may interfere

with each other.

EXAMPLE

NOTICE

To avoid scratching or breaking the

window, do not let the wiper arm

strike the window while replacing the

wiper blade.

EXAMPLE

Inspection and Maintenance -> Bulb replacement for Your Suzuki Ignis SUV First Generation (2000-2008)

Related Topics

Popular Owner Manuals

Latest Owner Manuals