2016-2024 Suzuki Ignis SUV Before Driving -> Child restraint system for countries applied for UN Regulation No.16 User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Before Driving -> Child restraint system for countries applied for UN Regulation No.16 for Your Suzuki Ignis SUV Second Generation (2016-2024)

2-43
BEFORE DRIVING
75RM4-01E
Child restraint system for countries applied for UN Regulation No.16
Child restraint
The suitability of each passenger’s seat position for carriage of children and fitting of child restraint system is shown in the table below.
Whenever you carry children under 12 years of age or smaller than 150 cm, properly use the child restraints which conform to UN Regu-
lation No. 44, the standard for child restraints, referring to the table.
Installation suitability of child restraint systems (For models with front passenger air bag deactivation system)
CAUTION
Adjust the height of the rear head restraint or remove it for fitting the child restraint, as necessary. However, if a booster
cushion not equipped with the head restraint is fitted, the rear seat head restraint should not be removed. If the rear head
restraint is removed for fitting the child restraint, you need to install it again after removing the child restraint.
If the child restraint is fitted improperly, a child sitting in it could be injured in a crash. (Refer to “Installation with lap-shoul-
der seat belts” section, “Installation with ISOFIX type anchorages” section and “Installation of child restraint with top tether”
section in this section for details.)
Mass Group
Seating position (or other site)
Front Passenger
Rear Outboard Rear Center
2)
Intermediate
Outboard
Intermediate
Center
Front passenger
airbag is
activated
Front passenger
airbag is
deactivated
group 0 up to 10 kg X U U U N.A. N.A.
group 0+ up to 13 kg X U
1)
U
1)
U
1)
N.A. N.A.
group I 9 to 18 kg X U U U N.A. N.A.
group II 15 to 25 kg X UF UF UF N.A. N.A.
group III 22 to 36 kg X UF UF UF N.A. N.A.
2-44
BEFORE DRIVING
75RM4-01E
Installation suitability of child restraint systems (For models without front passenger air bag deactivation system)
Key of letters to be inserted in the above table:
U =Suitable for ‘universal’ category restraints approved for use in this mass group
UF =Suitable for forward-facing ‘universal’ category restraints approved for use in this mass group
L =Suitable for particular child restraints given on attached list.
These restraints may be of the ‘specific vehicle’, ‘restricted’ or ‘semi-universal’ categories.
B =Built-in restraint approved for this mass group
X =Seat position not suitable for children in this mass group
NOTE:
1) SUZUKI recommends “Britax Römer Baby Safe i-Size” child seat.
This child restraint system is SUZUKI Genuine Accessory, refer to the accessories catalog. However, there are countries which do not
sell this child restraint system.
2) Child restraint system with support leg is prohibited in this seating position.
NOTE:
‘universal’ is the category in UN Regulation No. 44.
Mass Group
Seating position (or other site)
Front Passenger Rear Outboard Rear Center
2)
Intermediate
Outboard
Intermediate
Center
group 0 up to 10 kg X U U N.A. N.A.
group 0+ up to 13 kg X U
1)
U
1)
N.A. N.A.
group I 9 to 18 kg UF U U N.A. N.A.
group II 15 to 25 kg UF UF UF N.A. N.A.
group III 22 to 36 kg UF UF UF N.A. N.A.
2-45
BEFORE DRIVING
75RM4-01E
Installation suitability of ISOFIX child restraint systems (For models with front passenger air bag deactivation system)
Mass Group
Size
class
Fixture
Vehicle ISOFIX positions
Front
Passenger
Rear
Outboard
Rear
Center
Intermediate
Outboard
Intermediate
Center
Others
sites
carrycot
F ISO/L1 N.A. X N.A. N.A. N.A. N.A.
G ISO/L2 N.A. X N.A. N.A. N.A. N.A.
group 0 up to 10 kg E ISO/R1 N.A. IL N.A. N.A. N.A. N.A.
group 0+ up to 13 kg
E ISO/R1 N.A. IL N.A. N.A. N.A. N.A.
D ISO/R2 N.A. IL N.A. N.A. N.A. N.A.
C ISO/R3 N.A. IL N.A. N.A. N.A. N.A.
group I 9 to 18 kg
D ISO/R2 N.A. IL N.A. N.A. N.A. N.A.
C ISO/R3 N.A. IL N.A. N.A. N.A. N.A.
B ISO/F2 N.A. IL,IUF N.A. N.A. N.A. N.A.
B1 ISO/F2X N.A. IL,IUF
1)
N.A. N.A. N.A. N.A.
A ISO/F3 N.A. IL,IUF N.A. N.A. N.A. N.A.
group II 15 to 25 kg N.A. IL
2)
N.A. N.A. N.A. N.A.
group III 22 to 36 kg N.A. IL
2)
N.A. N.A. N.A. N.A.
2-46
BEFORE DRIVING
75RM4-01E
Installation suitability of ISOFIX child restraint systems (For models without front passenger air bag deactivation system)
Mass Group
Size
class
Fixture
Vehicle ISOFIX positions
Front
Passenger
Rear
Outboard
Rear
Center
Intermediate
Outboard
Intermediate
Center
Others
sites
carrycot
F ISO/L1 N.A. X N.A. N.A. N.A. N.A.
G ISO/L2 N.A. X N.A. N.A. N.A. N.A.
group 0 up to 10 kg E ISO/R1 N.A. IL N.A. N.A. N.A. N.A.
group 0+ up to 13 kg
E ISO/R1 N.A. IL N.A. N.A. N.A. N.A.
D ISO/R2 N.A. IL N.A. N.A. N.A. N.A.
C ISO/R3 N.A. IL N.A. N.A. N.A. N.A.
group I 9 to 18 kg
D ISO/R2 N.A. IL N.A. N.A. N.A. N.A.
C ISO/R3 N.A. IL N.A. N.A. N.A. N.A.
B ISO/F2 N.A. IL,IUF N.A. N.A. N.A. N.A.
B1 ISO/F2X N.A. IL,IUF
1)
N.A. N.A. N.A. N.A.
A ISO/F3 N.A. IL,IUF N.A. N.A. N.A. N.A.
group II 15 to 25 kg N.A. X N.A. N.A. N.A. N.A.
group III 22 to 36 kg N.A. X N.A. N.A. N.A. N.A.
2-47
BEFORE DRIVING
75RM4-01E
Key of letters to be inserted in the above table
IUF =Suitable for ISOFIX forward child restraints systems of universal category approved for use in this mass group
IL =Suitable for particular ISOFIX CRS are those of “specific vehicle”, “restricted” or “semi-universal” categories.
X =ISOFIX position not suitable for ISOFIX child restraint systems in this mass group and/or this size class.
NOTE:
1) SUZUKI recommends “Britax Römer Duo Plus” child seat.
2) SUZUKI recommends “Britax Römer KidFix XP” child seat.
These child restraint systems are SUZUKI Genuine Accessory, refer to the accessories catalog. However, there are countries which do
not sell these child restraint system.
NOTE:
‘universal’ is the category in UN Regulation No. 44.
Installation suitability of i-Size child restraint systems
Key of letters to be inserted in the above table
i-U =Suitable for i-Size “universal” Child Restraint Systems forward and rearward facing.
i-UF =Suitable for forward-facing i-Size “universal” Child Restraint Systems only.
X =Seating position not suitable for i-Size “universal” Child Restraint Systems.
NOTE:
‘universal’ is the category in UN Regulation No. 44.
Seating position
Front
Passenger
Outboard
Rear
Outboard
Left
Rear
Outboard
Right
Rear
Center
Intermediate
Outboard
Left
Intermediate
Outboard
Right
Intermediate
Center
i-Size Child
Restraint
N.A. i-U i-U N.A. N.A. N.A. N.A.
2-48
BEFORE DRIVING
75RM4-01E
Installation with lap-shoulder seat
belts
NOTE:
Stow the removed head restraint in the lug-
gage compartment so it will not cause
inconvenience to the occupants.
ELR type belt
80JC021
(For models with front passenger air bag
deactivation system)
Whenever possible, SUZUKI recom-
mends that child restraint systems be
installed on the rear seat. According to
accident statistics, children are safer when
properly restrained in rear seating posi-
tions than in front seating positions.
• If you must install the child restraint sys-
tem on the front passenger’s seat, follow
instructions below.
– Deactivate the front passenger’s front
air bag by the front passenger air bag
deactivation system.
– Slide the seat to the most rear position
by the seat position adjustment lever.
– Adjust the seatback at the 5th step
inclined position (counted from most
upright position) with the seatback
angle adjustment lever.
– If your vehicle is equipped with the
seat height adjustment lever, raise the
seat to the uppermost position by the
seat height adjustment lever.
Install your child restraint system accord-
ing to the instructions provided by the child
restraint system manufacturer.
Check that the seat belt is securely
latched.
Move the child restraint system in all direc-
tions to check that it is securely installed.
When you put your child in the child
restraint system, appropriately slide the
front seat forward not to touch a part of
your child’s body.
CAUTION
Adjust the height of the rear head
restraint or remove it for fitting the
child restraint, as necessary. How-
ever, if a booster cushion not
equipped with the head restraint is
fitted, the rear seat head restraint
should not be removed. If the rear
head restraint is removed for fitting
the child restraint, you need to install
it again after removing the child
restraint.
If the child restraint is fitted improp-
erly, a child sitting in it could be
injured in a crash.
EXAMPLE
2-49
BEFORE DRIVING
75RM4-01E
Installation with ISOFIX type
anchorages
75RM040
Your vehicle is equipped with the lower
anchorages in the rear seat outboard seat-
ing positions for securing a ISOFIX type of
child restraints with the connecting bars.
The lower anchorages are located where
the rear of the seat cushion meets the bot-
tom of the seatback.
Install the ISOFIX type child restraint sys-
tem according to the instructions provided
by the child restraint system manufacturer.
After installation, try moving the child
restraint system in all directions especially
forward to check that connecting bars are
securely latched to the anchorages.
84MM00252
Your vehicle is equipped with the top tether
anchorages. Use the top tether strap of the
child restraint according to the instructions
provided by the child restraint system man-
ufacturer.
Here is a general instruction:
NOTE:
Stow the removed head restraint in the lug-
gage compartment so it will not cause
inconvenience to the occupants.
WARNING
Install the ISOFIX type of child
restraint(s) in the only outboard seat-
ing positions, not in the central posi-
tion for the rear seat.
EXAMPLE
EXAMPLE
CAUTION
Adjust the height of the rear head
restraint or remove it for fitting the
child restraint, as necessary. How-
ever, if a booster cushion not
equipped with the head restraint is
fitted, the rear seat head restraint
should not be removed. If the rear
head restraint is removed for fitting
the child restraint, you need to install
it again after removing the child
restraint.
If the child restraint is fitted improp-
erly, a child sitting in it could be
injured in a crash.
2-50
BEFORE DRIVING
75RM4-01E
78F114
1) Place the child restraint in the rear seat,
inserting the connecting bars to the
anchorages between the seat cushion
and the seatback.
68LM268
2) Use your hands to carefully align the
connecting bar tips with the anchor-
ages. Take care not to pinch your fin-
gers.
54G184
3) Push the child restraint toward the anchor-
ages so that the connecting bar tips are
partially hooked to the anchorages. Use
your hands to confirm the position.
54G185
4) Grasp the front of the child restraint and
push the child restraint forcefully to
latch the connecting bars. Check that
they are securely latched by trying to
move the child restraint system in all
directions, especially forward.
5) Attach the top tether strap referring to
“Installation of child restraint with top
tether” section below.
When you put your child in the child
restraint system, appropriately slide the
front seat forward not to touch a part of
your child’s body.
EXAMPLE
EXAMPLE
EXAMPLE
EXAMPLE
2-51
BEFORE DRIVING
75RM4-01E
Installation of child restraint with
top tether
75RM105
Some child restraint systems require the
use of a top tether strap. Top tether anchor-
age brackets are provided in your vehicle at
the locations shown in the illustrations.
The number of the top tether anchorage
brackets provided in your vehicle depends
on the vehicle specification. Install the child
restraint system as follows:
1) Remove the luggage compartment cover
(if equipped).
2) Secure the child restraint on the rear
seat using the procedure described
above for securing a restraint system
that does not require a top tether strap.
3) Hook the top tether strap to the top
tether anchorage bracket and tighten
the top tether strap according to the
instructions provided by the child
restraint system manufacturer. Attach
the top tether strap to the correspond-
ing top tether anchorage bracket
located directly behind the child
restraint. Do not attach the top tether
strap to the luggage restraint loops (if
equipped).
54P000264
4) When routing the top tether strap, pass
the top tether strap as shown in the
illustration. (Refer to “Head restraints”
section for details on how to remove the
head restraint.)
5) Check that cargo does not interfere
with routing of the top tether strap.
NOTE:
For Australia:
For additional information, refer to the
“SUPPLEMENT” section at the end of this
book.
NOTICE
When installing a child restraint sys-
tem to the rear seat, adjust the front
seat position so that the front seat
does not interfere with the child
restraint system.
EXAMPLE
Front
WARNING
Do not attach the child restraint top
tether strap to the luggage restraint
loops (if equipped). Incorrectly
attached top tether strap will reduce
the intended effectiveness of the
child restraint system.
NOTICE
When installing a child restraint sys-
tem to the rear seat, adjust the front
seat position so that the front seat
does not interfere with the child
restraint system.
EXAMPLE

Related Topics

Before Driving
Keys Door locks Keyless push start system remote controller / Keyless entry system transmitter (if equipped) Theft deterrent alarm system (if equipped) Theft deterrent light (if equipped) Windows Mirrors Front seats Rear seats Seat belts and child restraint systems Seat belt pretensioner system Supplemental restraint system (air bags) Instrument cluster Speedometer Tachometer (if equipped) Fuel gauge Brightness control Information display (instrument cluster with tachometer) Information display (instrument cluster without tachometer) Warning and indicator lights Lighting control lever Headlight leveling switch (if equipped) Turn signal control lever Hazard warning switch Windshield wiper and washer lever Tilt steering lock lever Horn Heated rear window switch / heated outside rearview mirror switch (if equipped)

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot