Get Emergency Service -> Jacking instructions Guide for Suzuki Ignis SUV Second Generation (2016-2024)

8-1

EMERGENCY SERVICE

75RM4-01E

Tire changing tool

75RM076

(1) Jack (if equipped)

(2) Wheel brace

(3) Jack handle

The tire changing tools are stowed in the

luggage compartment.

Refer to “LUGGAGE COMPARTMENT” in

the “ILLUSTRATED TABLE OF CON-

TENTS” section.

75RM374

To remove the spare tire (if equipped), turn

its bolt (4) counterclockwise and remove it.

Jacking instructions

75F062

1) Place the vehicle on level, hard ground.

2) Set the parking brake firmly and shift

into “P” (Park) if your vehicle has a

CVT, or shift into “R” (Reverse) if your

vehicle has a manual transaxle/Auto

Gear Shift.

(3)

(2)

(1)

EXAMPLE

WARNING

After using the tire changing tools,

stow them securely or they can

cause injury if an accident occurs.

CAUTION

The jack should be used only to

change wheels. It is important to read

the jacking instructions in this sec-

tion before attempting to use the

jack.

(4)

WARNING

• Be sure to shift into “P” (Park) for a

CVT vehicle, or into “R” (Reverse)

for a manual transaxle/Auto Gear

Shift vehicle when you jack up the

vehicle.

• Never jack up the vehicle with the

transaxle in “N” (Neutral). Other-

wise, unstable jack may cause an

accident.

8-2

EMERGENCY SERVICE

75RM4-01E

3) Turn on the hazard warning flasher if

your vehicle is near traffic.

4) Block the front and rear of the wheel

diagonally opposite of the wheel being

lifted.

5) Place the spare wheel near the wheel

being lifted as shown in the illustration

in case the jack slips.

54G253

75RM077

75RM078

6) Position the jack at an angle as shown

in the illustration and raise the jack by

turning the jack handle clockwise until

the jack-head groove fits around the

jacking bar beneath the vehicle body.

7) Continue to raise the jack slowly and

smoothly until the tire clears the

ground. Do not raise the vehicle more

than necessary.

WARNING

• Use the jack only to change wheels

on level, hard ground.

• Never jack up the vehicle on an

inclined surface.

• Never raise the vehicle with the

jack in a location other than the

specified jacking point (shown in

the illustration) near the wheel to

be changed.

• Check that the jack is raised at

least 25 mm (1 inch) before it con-

tacts the flange. Use of the jack

when it is within 25 mm (1 inch) of

being fully collapsed may result in

failure of the jack.

• Never get under the vehicle when it

is supported by the jack.

• Never run the engine when the

vehicle is supported by the jack

and never allow passengers to

remain in the vehicle.

8-3

EMERGENCY SERVICE

75RM4-01E

Raising vehicle with garage jack

• Apply the garage jack to one of the

points indicated below.

• Always support the raised vehicle with

jack stands (commercially available) at

the points indicated below.

75RM360

(1) Front

(2) Jack stand

(3) Garage jack

(4) Rear

(5) Rear (4WD)

(6) Rear (2WD)

(7) Jacking point for garage jack

(4)

(1)

(2)

(7)

(1)

(3) (3) (3)

(5) (6)(7) (7)

8-4

EMERGENCY SERVICE

75RM4-01E

NOTE:

For more details, contact an authorized

SUZUKI dealer.

Changing wheels

To change a wheel, use the following pro-

cedure:

1) Remove the jack (if equipped), tools

and spare wheel from the vehicle.

2) Loosen, but do not remove the wheel

nuts.

3) Jack up the vehicle (follow the jacking

instructions in this section).

4) Remove the wheel nuts and wheel.

65J4033

5) Clean any mud or dirt off from the sur-

face of the wheel (1), hub (2), thread

part (3) and surface of the wheel nuts

(4) with a clean cloth. Clean the hub

carefully; it may be hot from driving.

6) Install the new wheel and replace the

wheel nuts with their cone shaped end

facing the wheel. Tighten each nut

snugly by hand until the wheel is

securely seated on the hub.

54G116

Tightening torque for wheel nut

85 Nm (8.7 kg-m, 62.7 lb-ft)

7) Lower the jack and fully tighten the nuts

with a wrench in numerical order as

shown in the illustration.

WARNING

• Be sure to shift into “P” (Park) in

CVT, or shift into “R” (Reverse) in

manual transaxle/Auto Gear Shift

when you jack up the vehicle.

• Never jack up the vehicle with the

transaxle in “N” (Neutral). Other-

wise, unstable jack may cause an

accident.

(2)

(

)

(1)

(3)

WARNING

Use genuine wheel nuts and tighten

them to the specified torque as soon

as possible after changing wheels.

Incorrect wheel nuts or improperly

tightened wheel nuts may come

loose or fall off, which can result in

an accident. If you do not have a

torque wrench, have the wheel nut

torque checked by an authorized

SUZUKI dealer.

8-5

EMERGENCY SERVICE

75RM4-01E

Full wheel cover (if equipped)

60G309

(1) or (2) Flat end tool

Your vehicle includes two tools, a wheel

brace and a jack crank, one of which has a

flat end.

Use the tool with the flat end to remove the

full wheel cap, as shown above.

54P000803

Install the full wheel cover not to cover or

foul the air valve.

Flat tire repair kit (if equipped)

The flat tire repair kit is stowed in the lug-

gage compartment.

Refer to “LUGGAGE COMPARTMENT” in

the “ILLUSTRATED TABLE OF CON-

TENTS” section.

EXAMPLE

WARNING

Failure to follow the instructions in

this section for using the flat tire

repair kit can result in an increased

risk of loss of control and an acci-

dent.

Carefully read and follow the instruc-

tions in this section.

Emergency Service -> Jacking instructions for Your Suzuki Ignis SUV Second Generation (2016-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals